AFS Series

Interface Terminal Block (screw type)

Features
● Compact interface terminal blocks with 7mm terminal pitch
● Optimized for connector type PLCs and input/output of
dedicated controllers
● Compact, space-saving design
● 2 mounting methods (DIN rail, screw mount)

※Autonics I/O cable CJ Series is recommended.

Please refer to ‘I/O cable’ in the I/O terminal block catalogue.
Please read “Safety Considerations” in instruction
manual before using.

Ordering Information
Model Item Terminal type Connector type The number of connector pin
AFS-H20 20-pin
Interface Hirose
AFS-H40 Screw 40-pin
terminal block connector
AFS-H50 50-pin

Terminal Specifications
B B
A A
D
C
D
C

<Spade terminal> <Ring terminal>

(unit: mm)
A B C D Applicable wire
Spade terminal ≥4.1 ≥16.0 ≥3.0 ≤5.9 AWG 22-16
Ring terminal ≥4.1 ≥16.0 ≥3.0 ≤5.9 (0.30 to 1.25mm2)

※ Please use UL certified terminals.

Specifications
Model AFS-H20 AFS-H40 AFS-H50
Power supply ≤125VDCᜡ, 125VACᜠ 50/60Hz
Rated current ≤1A
The number of connector pin 20-pin 40-pin 50-pin
The number of terminal 20 40 50
Terminal pitch 7.0mm
Applicable wire AWG22-16 (0.30 to 1.25mm²)
Insulation resistance ≥1,000MΩ (at 500VDC megger)
Dielectric strength 600VAC 50/60Hz for 1 min
Vibration 0.75mm amplitude at frequency of 10 to 55 Hz (for 1 min) in each X, Y, Z direction for 2 hours
Shock 150m/s2 (approx. 15G)in each X, Y, Z direction for 3 times

Environ- Ambient temperature -15 to 55℃, storage: -25 to 65℃

ment
Ambient humidity 35 to 85%RH, storage: 35 to 85%RH
Material Case: MPPO, terminal pin: Brass
Tightening torque 0.5 to 0.6 N·m
Approval
※1
Weight Approx. 103g (approx. 71g) Approx. 175g (approx. 133g) Approx. 211g (approx. 163g)

※1: The weight includes packaging. The weight in parenthesis is for unit only.
※Environment resistance is rated at no freezing or condensation.

A-6
 Interface Terminal Block

Dimensions I/O Terminal Blocks

Interface
● AFS-H20 (unit: mm) Terminal Blocks
Common
Terminal Blocks

80 2-Ø3.5 Sensor Connector

Terminal Blocks
62.5 Relay
Terminal Blocks

I/O Cables

10.5

41.8
39.5
Remote I/O
11

Others

20-M3
7 39.7
5.9

45.8
32.5

35.2

● AFS-H40 / AFS-H50

2-Ø3.5
A
B
AFS Series
AFS-H40 AFS-H50
AFL Series
A 150 184
10.5

AFR Series
B 89 104
39.5

41.8

C 45.8 48.9
11

D 39.7 34.8

7 40-M3, D
5.9 50-M3
C
32.5

35.2

● Jumper bar (sold separately)

7 2.7
3.2 0.8
9.5

10.9

[N]

Model JB-7-04 JB-7-10

The number of Jumper bar pin 4 10
[ N ] size 27.5 69.5

A-7
AFS Series

Wire Connections
● AFS-H20
※Hirose connector 2 4 6 8 10 12 14 16 18 20
: HIF3BA-20PA-2.54DSA Connector
1 3 5 7 9 11 13 15 17 19
2 20

1 19 B1 B2 B3 B4 B5 B6 B7 B8 B9 B10
Terminal
block A1 A2 A3 A4 A5 A6 A7 A8 A9 A10

● AFS-H40 / AFS-H50
※Hirose connector ※Hirose connector model
: HIF3BA-40PA-2.54DSA : HIF3BA-50PA-2.54DSA
2 40 2 50

39 49
1 1

2 4 6 8 10 12 14 16 18 20 22 24 26 28 30 32 34 36 38 40 42 44 46 48 50
Connector
1 3 5 7 9 11 13 15 17 19 21 23 25 27 29 31 33 35 37 39 41 43 45 47 49

B1 B2 B3 B4 B5 B6 B7 B8 B9 B10 B11 B12 B13 B14 B15 B16 B17 B18 B19 B20 B21 B22 B23 B24 B25
Terminal
block A1 A2 A3 A4 A5 A6 A7 A8 A9 A10 A11 A12 A13 A14 A15 A16 A17 A18 A19 A20 A21 A22 A23 A24 A25

※Dot line part is only for AFS-H50 model.

Installation
Mounting and removal at DIN rail Mounting with screws
● Mounting 1)The unit can be mounted on panels using the
1)Pull the rail lock towards direction ①. mounting holes next to the hirose connector.
2)Attach the DIN rail connection hook onto the DIN 2)M3 × 30mm spring washer screws are
rail. recommended for installation. When using flat
washers, use Ø6mm diameter washers. The
3)Push the unit towards direction ②, then push the rail
tightening torque should be from 0.5 to 0.7 N·m.
lock in to lock into position.
DIN rail
connection part Mounting holes

DIN rail

① Rail lock ②

● Removal
1)Insert a screwdriver into the rail lock hole and pull it
towards direction ①.
2)Remove the unit by pulling the unit towards
direction ②.
①
②

Rail lock

A-8
 Interface Terminal Block

Installing Jumper Bars I/O Terminal Blocks

Interface
1)Cut the jumper bar to the user's desired length by 2)Unfasten all the screws of the terminals you wish to Terminal Blocks

cutting at the V dent using a nipper. commonize. Common

Terminal Blocks
Sensor Connector
Terminal Blocks
Relay
Terminal Blocks

I/O Cables

Remote I/O

Others

V dent

3)Insert the jumper bar below the unfastened screws. 4)Tighten all the screws above the jumper bar.

AFS Series

AFL Series

AFR Series

Cautions during Use

1. Do not use the product outside of rated temperature and humidity.
2. Check to make sure that voltage fluctuation in the power supply is within the rated range.
3. When connecting PLC or other controllers, check the power polarity before wiring.
4. Use AWG 16 (1.25mm2) wire and use appropriate connectors for the terminals.
5. Do not connect or disconnect the connector or perform any wiring work while supplied with power.
6. Do not use the unit in the following environments.
① Environments with high vibration or shock
② Environments where strong alkalis or acids are used
③ Environments with exposure to direct sunlight
④ Near machinery which produce strong magnetic force or electric noise
7. This unit may be used in the following environments.
① Indoors
② Altitude max. 2,000m
③ Pollution degree 2
④ Installation category II

A-9