ABS Series Relay Terminal Block

Relay terminal block

▣Features (A)
I/O
Terminal
Suitable to drive various loads using output signals of PLC
(B)
Easy check for operation status and for cable break by I/O Cable

adopting LED signal

Available 2 types of relay[TAKAMISAWA(Fujitsu) NYP/
MATSUSHITA(Panasonic) PA]
- Supports TWO WAY EJECTOR(for relay replacement)
Two ways of mounting(DIN Rail, bolt fix)

▣Ordering information

AB S H 16 PA N N

Varistor installation
N No install

Input logic
C Non-COM
N NPN (COM+)
P PNP (COM-)
Relay type TN TAKAMISAWA (Fujitsu) NYP
AFS
PA MATSUSHITA (Panasonic) PA
04 04pcs
Number of relays ACS
16 16pcs
32 32pcs
AFE
Connector type S Screw
H Hirose connector
Terminal type ABS
S Screw
Item
AB Relay terminal block
Relay

▣Applicable crimp terminal

B B
A A
D
C
D
C

<Forked> <Round>
(Unit:mm)
A B C D Applicable wires
Forked Min. 4.1 Max. 16.0 Min. 3.0 Max. 5.9 AWG 22-16
Round Min. 4.1 Max. 16.0 Min. 3.0 Max. 5.9 (0.30 to 1.25mm2)

A-13
ABS Series

▣Specifications
ABS-S04PA-CN ABS-H16PA-NN(PN) ABS-H32PA-NN(PN)
Model
ABS-S04TN-CN ABS-H16TN-NN(PN) ABS-H32TN-NN(PN)
Rated voltage 24VDC ±10%
Rated load voltage & 250VAC 2A, 30VDC 2A※1
current 250VAC 3A, 30VDC 3A※1
(2A/1point, 8A/1COM)
Power PA type Max. 10.5mA ※2 Max. 10.5mA ※1/Max. 15.5mA ※3
consumption TN type Max. 8.5mA ※2 Max. 8.5mA ※1/Max. 13.5mA ※3
Output type 1a contact relay output
Number of output 4point 16point 32point(8point/1COM)
Number of connectors ─ 20pin 40pin
Number of terminals 8ea 34ea 40ea
Terminal pitch 7.62mm
Applicable wire Min. 1.25mm2
Insulation resistance Min. 1,000㏁ (at 500VDC megger)
2000VAC 50/60Hz for 1 minute (coil and contacts)
Dielectric strength
1000VAC(Fujitsu relay: 750VAC) 50/60Hz for 1 minute (open contacts)※4
Vibra- Vibration 0.75mm amplitude at frequency of 10 to 55Hz in each X,Y,Z direction for 2 hour
resistance
tion Malfunction 0.75mm amplitude at frequency of 10 to 55Hz in each X,Y,Z direction for 10 minutes
Shock 500m/s2(50G) in X, Y, Z directions for 3 times
Shock resistance
Malfunction 147m/s2(15G) in X, Y, Z directions for 3 times
Ambient -15 to 55℃, Storage: -25 to 65℃
Environ- temperature
ment Ambient 35 to 85%RH, Storage: 35 to 85%RH
humidity
CASE & BASE: MPPO, CASE: MPPO, BASE: PA66(G25%)
Material
TERMINAL PIN: Brass TERMINAL PIN: Brass
Tightening torque 0.4 to 0.6 N.m
Accessory ※5 Jumper Bar: 2EA (Model No: JB-7.62-04) Jumper Bar: 2EA (Model No: JB-7.62-08) ─
Unit weight PA: Approx. 68g, TN: Approx. 71g PA: Approx. 224g, TN: Approx. 235g PA: Approx. 345g, TN: Approx. 370g
※1: Relay contact capacity for resistive load. ※4: For TN type(Fujitsu relay), dielectric strength is 750VAC.
※2: The power consumption including LED current by one relay. ※5: ABS-H32□□-NN(PN) does not provide Jumper Bar.
※3: The power consumption including LED current of power. ※Environment resistance is rated at no freezing or condensation.

▣Dimensions
ABS-S04PA-CN / ABS-S04TN-CN Jumper Bar
2-Φ4.5
7.62 2.7

3.2 0.8
9.5
79

10.9
35.2
70
72
10

[N]
7.62 5.9 16-M3
32
Model JB-7.62-04 JB-7.62-08
Number of pins 4ea 8ea
38

[ N ] Size 29.5 60.0

ABS-H16PA-□N / ABS-H16TN-□N ABS-H32PA-□N / ABS-H32TN-□N

A
B 4-Φ4.5
84
79

35.2
70
72
11

34-M3 (ABS-H16) 34
5.9 7.62 40-M3 (ABS-H32)

ABS-H16 type ABS-H32 type

A 140 173
37

B 70 100
(Unit:mm)

A-14
 Relay Terminal Block

▣Wire connections
ABS-S04PA-CN / ABS-S04TN-CN (A)
I/O
(-) (-) (-) (-) Terminal
4 3 2 1
(B)
INPUT (+) (+) (+) (+) I/O Cable
8 7 6 5

RY4 RY3 RY2 RY1

OUTPUT 12 11 10 9

16 15 14 13

ABS-H16□-NN 2 20
※Hirose connector model no.
19 : HIF3BA-20PA-2.54DSA
1
Connectors

3 4 1 2 20 18 16 14 12 10 8 6 19 17 15 13 11 9 7 5

Terminals

24VDC R1+ R2+ R3+ R4+ R5+ R6+ R7+ R8+ R9+ R10+ R11+ R12+ R13+ R14+ R15+ R16+
GND R1- R2- R3- R4- R5- R6- R7- R8- R9- R10- R11- R12- R13- R14- R15- R16-

ABS-H16□-PN
Connectors
3 4 1 2 20 18 16 14 12 10 8 6 19 17 15 13 11 9 7 5

AFS

ACS
Terminals

GND R1+ R2+ R3+ R4+ R5+ R6+ R7+ R8+ R9+ R10+ R11+ R12+ R13+ R14+ R15+ R16+
AFE
24VDC R1- R2- R3- R4- R5- R6- R7- R8- R9- R10- R11- R12- R13- R14- R15- R16-

ABS
ABS-H32□-NN 2 40
※Hirose connector model no.
39 : HIF3BA-40PA-2.54DSA
1 Relay
1 3 2 4 40 38 36 34 32 30 28 26 24 22 20 18 16 14 12 10 39 37 35 33 31 29 27 25 23 21 19 17 15 13 11 9
Connectors

Terminals +24V +24V COM1 R2 R4 R6 R8 R9 R11 R13 R15 COM3 R18 R20 R22 R24 R25 R27 R29 R31
GND GND R1 R3 R5 R7 COM2 R10 R12 R14 R16 R17 R19 R21 R23 COM4 R26 R28 R30 R32

ABS-H32□-PN

Connectors 1 3 2 4 40 38 36 34 32 30 28 26 24 22 20 18 16 14 12 10 39 37 35 33 31 29 27 25 23 21 19 17 15 13 11 9

GND GND COM1 R2 R4 R6 R8 R9 R11 R13 R15 COM3 R18 R20 R22 R24 R25 R27 R29 R31
Terminals
+24V +24V R1 R3 R5 R7 COM2 R10 R12 R14 R16 R17 R19 R21 R23 COM4 R26 R28 R30 R32

A-15
ABS Series

▣How to install jumper bar

1)Cut the jumper bar for the desired length to fit 2)Unfasten the terminal screws for common.
cutting V groove with nipper, etc.

Jumper bar cutting

V groove

3)Put jumper bar under the unfastened terminal 4)Tighten all of screws upside the jumper bar.
screws.

▣How to replace relay

The position of Two way ejector for relay replacement
TAKAMISAWA(Fujitsu) RELAY replace position

MATSUSHITA(Panasonic) RELAY replace position

< TWO WAY EJECTOR >

TWO WAY EJECTOR

for relay replacement

TWO WAY EJECTOR

for relay replacement

< ABS-S04 type > < ABS-H16 / ABS-H32 type >

Mount and Remove TAKAMISAWA(Fujitsu) relay Mount and Remove MATSUSHITA(Panasonic) relay

< Remove FUJITSU relay > < Mount FUJITSU relay > < Remove FUJITSU relay > < Mount FUJITSU relay >

※Relay socket can be used both TAKAMISAWA(Fujitsu) relay (NYP24W-K) and MATSUSHITA(Panasonic)
relay (PA1a-24V).

A-16
 Relay Terminal Block

▣Installation
◎Mounting to and Removing from DIN Rail ◎Fixing with bolt (A)
I/O
Mounting 1)Screw insertion holes are used for mounting Terminal
1)Push Rail Lock to the direction “①”. the unit on panel.
(B)
2)Hook DIN Rail connector onto DIN Rail. 2)It is recommended to use M4×15mm of spring I/O Cable
3)Push the unit down to the direction “②” and washer screws and to use flat washers which
then push up the Rail Lock to the opposite are diameter Ø6.
direction “①”. The tightening torque should be 0.7 to 1.0N·m.

DIN Rail
connector

DIN Rail

②
Rail Lock

① ①

Removing
1)Insert a screwdriver into hole of Rail Lock
and pull the lock out to the direction “①”.
2)Remove the unit by pulling to the direction “②”.
①

Rail Lock

▣Caution for using AFS

1. Use the product within the specified ratings for operating temperature and humidity.
ACS
2. Maintain voltage fluctuations in the power supply within specified range.
3. Check the polarity of power and wrong wiring.
AFE
4. Use AWG 16(1.25mm2)wire and applicable crimp terminals to the terminal block.
5. Always turn OFF the power supply before wiring or removing connectors.
ABS
6. Power shall be disconnected before replacing relay.
7. Do not use this unit at below places.
Relay
(1) Place where there is severe vibration or impact.
(2) Place where strong alkalis or acids are used.
(3) Place where there are direct ray of the sun.
(4) Place where strong magnetic field or electric noise are generated.
8. Installation environment.
(1) It shall be used indoor (2) Altitude Max. 2000m
(3) Pollution Degree 2 (4) Installation Category II

A-17
POWER RELAY

TAKAMISAWA(Fujitsu) Power relay 1 POLE-5A NYP24W-K

▣Features
Slim type with 5mm thickness (Useful to density mounting)
Low power consumption and high sensitivity
Semipermanent life cycle (Suitable for a lot of switching frequency)

▣Coil ratings
Model Nominal voltage Must operate voltage Must release voltage Nominal current Coil resistance Power consumption
NYP24W-K 24VDC 16.1V 2.4V 5mA 4,800Ω 120mW
※All values in the table are measured at 20℃ with a tolerance of ±20%

▣Contact ratings
Maker TAKAMISAWA(Fujitsu)
Model NYP24W-K
Arrangement 1 Form A (SPST-1a)
Contact Material Gold overlay silver alloy
Resistance(inital) 30mΩ (6VDC 1A)
Rating (resistive) 3A 250VAC 3A 30VDC
Max. switching power 750VA 90W
Rating Min. switching capacity 5VDC 1mA
Max. switching voltage 270VAC 150VDC
Max. switching currrnt 5A
Insulation resistance Min. 1,000㏁ (at 500VDC megger)
coil and
Dielectric contacts 3,000VAC 50/60Hz for 1 minute
Electrical strength
character- open contacts 750VAC 50/60Hz for 1 minute
istics Surge voltage 5,080V
Operate time Max. 10ms
Release time Max. 5ms
Vibration
5.0mm amplitude at frequency of 10 to 55Hz in each X,Y,Z direction for 1 hour
Vibration resistance
Mechanical Malfunction 1.5mm amplitude at frequency of 10 to 55Hz in each X,Y,Z direction for 10 minutes
character-
istics Shock
1000m/s2 (100G) in X, Y, Z directions for 3 times
Shock resistance
Malfunction 100m/s2 (10G) in X, Y, Z directions for 3 times
Expected Mechanical 20,000,000 operations min. (at 180 times/min)
life Electrical※1 100,000 operations min. (3A 250VAC, 30VDC resistive load)
Ambient temperature -40 to 90℃
Environment
Ambient humidity 35 to 80%RH
Unit weight Approx. 3.5g
※1: 50,000 operations min.-5A 250VAC, 30VDC resistive load.(at 20times/min)
※Environment resistance is rated at no freezing or condensation.

▣Dimensions
22.9
+0.08
20.1
17.5+0.2

0.98
(Unit:mm)

A-18
 POWER RELAY

MATSUSHITA(Panasonic) Power relay 1 POLE-5A PA1a-24V

▣Features (A)
I/O
Terminal
Slim type with 5mm thickness (Enable to density mounting)
(B)
Excellent durability resistance against vibration and shock I/O Cable

Semipermanent life cycle (Suitable for a lot of switching frequency)

▣Coil ratings
Model Nominal voltage Must operate voltage Must release voltage Nominal current Coil resistance Power consumption
70% max. of 5% min. of
PA1a-24V 24VDC 7.5mA 3,200Ω 180mW
Nominal voltage Nominal voltage
※All values in the table are measured at 20℃ with a tolerance of ±20%

▣Contact ratings
Maker MATSUSHITA(Panasonic)
Model PA1a-24V
Arrangement 1 Form A (SPST-1a)
Contact Material Au-clad AgNi type
Resistance(inital) 30mΩ (6VDC 1A)
Rating (resistive) 5A 250VAC 5A 30VDC
Max. switching power 1,250VA 150W
Rating Min. switching capacity 100mVDC 100uA
Max. switching voltage 250VAC 110VDC
Max. switching currrnt 5A
Insulation resistance Min. 1,000㏁ (at 500VDC megger)
coil and
Dielectric contacts 2,000VAC 50/60Hz for 1 minute
Electrical strength
character- open contacts 1,000VAC 50/60Hz for 1 minute AFS
istics Surge voltage 4,000V
Operate time Max. 10ms ACS
Release time Max. 5ms
Vibration
13.5mm amplitude at frequency of 10 to 55Hz in each X,Y,Z direction for 1 hour AFE
Vibration resistance
Mechanical Malfunction 2.5mm amplitude at frequency of 10 to 55Hz in each X,Y,Z direction for 10 minutes
character- ABS
istics Shock
980m/s2 (100G) in X, Y, Z directions for 3 times
Shock resistance
Malfunction 147m/s2 (15G) in X, Y, Z directions for 3 times Relay

Expected Mechanical 20,000,000 operations min. (at 180 times/min)

life Electrical※1 100,000 operations min. (3A 250VAC, 30VDC resistive load)
Ambient temperature -40 to 70℃
Environment
Ambient humidity 5 to 85%RH
Unit weight Approx.3g
※1: 50,000 operations min.-5A 250VAC, 30VDC resistive load.(at 20times/min)
※Environment resistance is rated at no freezing or condensation.

▣Dimensions
0.5 Schematic (Bottom view)

1.2
(12.8 max.)

2.9
12.5
1.3
8.8

4.8

N.O COM
6

Coil
3.5

5 0.5 0.8 0.25

2.54 10.16 5.08 1.11 1.18
20 (Unit:mm)
※Allowance : ±0.3

A-19