A320M-M.

2 PRO V15
B450M-K PRO V14
Colorful Technology Website:
http://www.colorful.cn
Thanks for purchasing Colorful series motherboard. This series of motherboards provides excellent performance and quality
assurance.

A320M-M.2 PRO V15/B450M-K PRO V14 motherboard based on AMD A320/B450 Chipset,support AM4 AMD processors, support
dual channel DDR4 3200（OC）/3000（OC）/2800（OC）/2666/2400/2133MHz memory, support PCI-E 3.0 standard.

The motherboard provides 1*HDMI port,1*VGA port,2*DDR4 memory slots,4*SATA3.0 6Gb/s ports,4*USB3.0 and 6*USB2.0 ports
(include headers),onboard 6-CH audio chipset,onboard 1000M LAN chipset, it’s a Cost-effective motherboard ！

The motherboard provides 1*PCI Express3.0 x16 slot,1*PCI Express 3.0 x1 slot,1*M.2 slot,it had good extensibility ！

1.1.Packing Contents
1* Colorful A320M-M.2 PRO V15/B450M-K PRO V14 motherboard
2* SATA cables
1* Driver/Utility CD
1* User's Guide
1* I/O shield

1.2.MOTHERBOARD SPEC
·Supports Socket AM4
CPU ·1*24-pin ATX Power connector
·Support AMD AM4 CPUs
·1* 4-pin ATX 12V Power connector
Chipset ·A320M-M.2 PRO V15 uses AMD A320 ·1*Front panel audio connector（F_PANEL）
·B450M-K PRO V14 uses AMD B450 ·1*System panel connector（F_AUDIO）
·Offer 2 DIMM slots ·1*USB2.0 header（FUSB20_1）
·Support DDR4 3200（OC）/3000（OC）/2800（OC）/2666/2400 ·1*USB3.0 header（FUSB30_1）
Main ·1*PC speaker connector（SPEAK）
/2133 MHz Other
Memory ·1*Debug header（DEBUG）
·Tips:the frequency of memory overclocking also depends Connectors
on the performance of matching CPU and memory itself! ·1*SPDIF header（JSPDIF）
·2*Fan header（CPU_FAN，SYS_FAN）
·1*PCI Express 3.0 x16 slot ·1*12V 4Pin RGB fan header（FAN_RGB_HEADER）
Slots ·1*PCI Express 3.0 x1 slot ·1*Flash BIOS header（JBIOS1）
·1*M.2 slot ·1*The power off charging and PS2 mouse/keyboard
Storage ·4*SATA3.0 port wake up jumper（JKB）
·1*Clear CMOS jumper（CLR_CMOS）
USB ·4*USB3.0+6*USB2.0(including the headers)
High ·Onboard 6-channel High Definition audio chipset
Definition
·1*PS/2 Mouse or Keyboard port ·Support 3D surround sound
Audio
·1*LAN(RJ45) port
·4*USB 2.0 ports
Rear IO Onboard ·Onboard 1000M LAN
·2*USB3.0 ports
Connector LAN ·Provides 10/100/1000Mb Ethernet
·3*Audio ports(audio in,audio out, microphone)
·1*VGA port
·1*HDMI port
 1.3.Motherboard Layout
1、PS/2 Mouse/Keyboard and USB2.0 ports
2、Connect to HDMI monitor
3、Connect to VGA monitor
4、Connect to USB3.0 devices
5、Connect to USB2.0 devices and LAN
6、Connect to audio devices
7、Power off charging and PS2 mouse
/keyboard wake up jumper
8、4-pin Power connector
9、AMD AM4 socket
10、CPU fan connector
11、DIMM slots (DDR4)
12、24-pin ATX Power connector
13、SATA3.0 ports
14、Flash Bios header
15、12V 4Pin RGB FAN header
16、System fan connector
17、PCI Express 3.0 X16 slot, for VGA Card
18、DEBUG header 27
19、Clear CMOS jumper
20、PCI Express 3.0 X1 slot
21、Front panel audio connector
22、SPDIF header
23、Speaker connector
24、USB 3.0 header
25、USB 2.0 headers
26、Front power on / off , restart ,
indicator light header
27、M.2 slot 21 24 25 26
22 23

This section will guide you through the installation of the motherboard. The topics covered in this section are:
Preparing the motherboard
Installing the CPU
Installing the CPU fan
Installing the memory
Installing the motherboard
Connecting cables and setting switches

2.1.Safety Instructions
To reduce the risk of fire, electric shock, and injury, always follow basic safety precautions.
Remember to remove power from your computer by disconnecting the AC main source before removing or installing any equip-
ment from/to the computer chassis.
2.2.Preparing the Motherboard
The motherboard shipped in the box does not contain a CPU or memory. You need to purchase a CPU, a CPU fan assembly, and
memory to complete this installation.

2.2.1.Installing the CPU

When installing a CPU, always remember to install a CPU heatsink. An CPU heatsink is necessary to prevent overheating and main-
tain system stability. Follow the steps below to ensure correct APU and heatsink installation. Wrong installation can damage both
the APU and the motherboard.
1. Pull the lever sideways away from the socket. Make sure to raise the lever up to a 90-degree angle.
2. Locate the pin one (denoted by a small triangle) of the CPU socket and the CPU..
3. If the CPU is correctly installed, the pins should be completely embedded into the socket and can not be seen. Please note that
any violation of the correct installation procedures may cause permanent damages to your motherboard.
4. Press the CPU down firmly into the socket and close the lever. As the CPU is likely to move while the lever is being closed, always
close the lever with your fingers pressing tightly on top of the CPU to make sure the CPU is properly and completely embedded
into the socket.
5. Locate the CPU fan connector on the motherboard.
6. Position the cooling set onto the retention mechanism. Hook one end of the clip to hook first.
7. Then press down the other end of the clip to fasten the cooling set on the top of the retention mechanism. Locate the Fix Lever
and lift up it.
8. Fasten down the lever.
9. Attach the CPU Fan cable to the CPU fan connector on the motherboard.

2.3.Installing Memory DIMMs

Your new motherboard has 2 slots for DDR4 memory. They support dual channel DDR4 memory technology. There must be at least
one memory bank populated to ensure normal operation. Use the following the recommendations for installing memory.
One DIMM: Install into DIMM1 or DIMM2. You can install the DIMM into any slot, however, slot 1 is preferred.
Two DIMMs: Install into DIMM1 & DIMM2,to build dual channel.

Use the following procedure to install memory DIMMs into the slots on the motherboard. Note that there is only one gap near the
center of the DIMM slot. This slot matches the slot on the memory DIMM to ensure the component is installed properly.
Unlock a DIMM slot by pressing the module clips outward.
Align the memory module to the DIMM slot, and insert the module vertically into the DIMM slot. The plastic clips at both sides
of the DIMM slot automatically lock the DIMM into the connector.
2.4.Installing the Motherboard
The sequence of installing the motherboard into the chassis depends on the chassis you are using and if you are replacing an
existing motherboard or working with an empty chassis. Determine if it would be easier to make all the connections prior to
this step or to secure the motherboard and then make all the connections. Use the following procedure to install the I/O
shield and secure the motherboard into the chassis.

Be sure that the CPU fan assembly has enough clearance for the chassis covers to lock into place and for the expansion
cards. Also make sure the CPU Fan assembly is aligned with the vents on the covers.

2.5.Installing the I/O Shield

The motherboard kit comes with an I/O shield that is used to block radio frequency transmissions, protects internal compo-
nents from dust and foreign objects, and promotes correct airflow within the chassis.
Before installing the motherboard, install the I/O shield from the inside of the chassis. Press the I/O shield into place and
make sure it fits securely. If the I/O shield does not fit into the chassis, you would need to obtain the proper size from the
chassis supplier.

2.6.Securing the Motherboard into the Chassis

Most computer chassis have a base with mounting studs or spacers to allow the mother board to be secured to the chassis
and help to prevent short circuits. If there are studs that do not align with a mounting hole on the motherboard, it is recom-
mended that you remove that stud to prevent the possibility of a short circuit.
1.Carefully place the motherboard onto the studs/spacers located inside the chassis.
2.Align the mounting holes with the studs/spacers.
3.Align the connectors to the I/O shield.
4.Ensure that the fan assembly is aligned with the chassis vents according to the fan assembly instruction.
5.Secure the motherboard with a minimum of eight-to-ten screws.
 2.7.Connecting Cables and Setting Switches
This section takes you through all the connections and switch settings necessary on the motherboard. This will include:
Power Connections
24-pin ATX power
4-pin ATX 12V power
Internal Headers
Front panel
USB Headers
Audio
Serial ATA III
Chassis Fans
Rear panel USB 2.0 Adapter
Expansion slots
2.7.1.ATX power connectors (24-pin ATXPWR, 4-pin ATX12V)
These connectors are for an ATX power supply. The plugs from the power supply are designed to fit these connectors in only
one orientation. Find the proper orientation and push down firmly until the connectors completely fit.

2.7.2.Power off charging and PS2 mouse/keyboard wake up jumper

Only the PS2+USB ports on the back panel can support the shutdown charging function.You can open this function by short-
ing 2-3pin.
Note: the white silk-screen "1" on the PCB is the first needle of jumper.
2.7.3.Serial ATA 3.0 6Gb/s connectors (7-pin)
These connectors connect to Serial ATA 3.0 6Gb/s
hard disk drives and optical drives via Serial ATA 3.0
6Gb/s signal cables.

2.7.4.USB2.0 connectors
These connectors are for USB 2.0 ports. Connect the USB module cable to any of these connectors, then install the module to a
slot opening at the back of the system chassis. These USB connectors comply with the USB 2.0 specification that supports up to
480Mbps connection speed.

2.7.5.SPEAK header：
This SPEAK header is for Speaker serial devices
2.7.6.System panel connector
This connector supports several chassis-mounted functions.

Short circuit these two pins to

power on

Short circuit these two pins to

restart

2.7.7.PCI Express3.0 x16 and PCI Express x1 slots

The PCI Express x1 slots that are designed to accommodate less bandwidth-intensive cards, such as a modem or LAN card. The x1
slot provides 250 MB/sec bandwidth.
The PCI Express3.0 x16 slot is reserved for a graphics or video card. The bandwidth of the x16 slot is up to 4GB/sec (8GB/sec
concurrent).
When installing a PCI Express3.0 x16 card, be sure the retention clip snaps and locks the card into place. If the card is not seated
properly, it could cause a short across the pins. Secure the card’s metal bracket to the chassis back panel with the screw used
to hold the blank cover.

PCI Express3.0 x16 Slot

PCI Express x1 Slot

2.7.8.Front panel audio connector

This connector is for a chassis-mounted front panel audio I/O module that supports either High Definition Audio or AC`97 audio
standard. Connect one end of the front panel audio I/O module cable to this connector.
2.7.9.Clear CMOS Jumper: CLR_CMOS
There is a CMOS RAM on board that has a power supply from external battery to keep the system configuration data. With the
CMOS RAM, the system can automatically boot OS every time it is turned on. If you want to clear the system configuration, use
the CLR_CMOS Jumper to clear data.
Clear CMOS PROCEDURE
You can clear CMOS by shorting 1-2 pin. Before you clearing the CMOS, following next procedure:
1.Turn off the AC power supply and connect pins 1 and 2 together using the jumper cap.
2.Return the jumper setting to normal (pin 1 or 2) or Remove the jumper cap
3.Turn the AC power supply back on.

1-2 clear CMOS 1or2 normal

Clear CMOS settings

2.7.10.M.2 slot
The motherboard has one M.2 slot,support PCI-e x4 and SATA SSD,support 2242/2280 size SSD.
Please install M.2 SSD correctly in the slot following the following steps:
1. please use a screwdriver to remove the screws and studs in order, and then lock the stud first when the actual M.2 SSD is found
to be suitable for the screw hole position.
2. insert the M.2 SSD into the slot in a inclined angle.
3. press M.2 SSD, then lock the screw.
2.7.11.CPU, Chassis, and Power fan connectors
Connect the fan cables to the fan connectors on the motherboard, making sure that the black wire of each cable matches the
ground pin of the connector.

2.7.12.12V 4-pin RGB Fan/ LED header

The motherboard offer two 12V 4-pin RGB LED Fan/Strip headers. During installation, the 12V pin on the RGB fan is aligned with
the 12V pin on the motherboard.
*Note: RGB LED Fan/Strip is optional equipment, please purchase separately.

2.7.13.USB 3.0 connectors

This connector is for USB 3.0 devices.
2.7.14.Back Panel IO Connector

<Backboard of A320M-M.2 PRO V15/B450M-K PRO V14>

Parts Use

PS/2 Mouse or Keyboard Connector This connector is for a PS/2 mouse or Keyboard.

The standard RJ-45 jack is for connection to single Local Area Network (LAN).
LAN Jack
You can connect a network cable to it
Lie-In(Blue) Used for external CD player, tape player or other audio devices.

Line Out(Green) This connector for speakers or headphones.

Side R/L(Gray) Side surround speakers connector

VGA Onboard VGA, connect to Monitor

HDMI Onboard HDMI port, connect to HDMI Monitor

These connectors are for attaching USB devices such as keyboard, mouse,
USB Ports
or other USB-compatible devices.

3.BIOS setup
The chapter contains the following:
·Main（System Information）
·Advanced（Advanced BIOS Features）
·Chipset（Chipset Settings）
·Security（Security Settings）
·Boot（Startup Settings）
·OC Drive（OverClock Settings）
Entering BIOS Setup
Power on the computer and the system will start the Power On Self Test (POST)process. When the message below appears on the
screen, press <DEL> key to enter BIOS:

Press F1 to Run Setup

Press F2 to Load default values and continue

(Press the <F1> key to enter BIOS Setup,press the <F2> key to load default values and continue)

If the boot self test (POST) program information is disappeared before you respond,you can turn it off and then turn on,or press
the Reset button on the chassis to restart your computer, can also press < Ctrl > + < Alt > + < Delete > to restart the computer.
BIOS Setup Program Function Keys
< ↑↓ > Upward and downward move to select a setup menu
< ← → > To the left and right move to select a setup menu
< Enter > Execute command or enter a menu
< Esc > Main Menu: Exit the BIOS Setup program
Submenus: Exit current submenu
< F1 > Help topic(Only the status display menu and select Settings menu are valid)
< F7 > Restore the previous CMOS settings
< F9 > Load Optimized Defaults
< F10 > Save all the changes and exit the BIOS setup program
The BIOS settings can be operated with the mouse.

BIOS Main Menu

Main Advanced Chipset Security Boot OC Drive

BIOS Information
BIOS Vendor American Megatrends
Core Version 5.14
Compliancy UEFI 2.7；PI 1.6
Project Version AM40A05-904
→←Select Screen
Build Date and Time 07/25/2020 10:41:47
↑↓:Choose Item
Access Level Administrator
Enter: Select
Total Memory 4096MB(DDR4)
+/-: Change Opt
Memory Speed 2400MHZ
F1: General Help
F7: Previous Values
System Language English
F8：Print Screen
System Date 07/30/2020
F9: Optimized Defaults
System Time 13: 45: 49
F10: Save & Exit
ESC: Exit

Boot（Startup Settings）
Boot Option Priorities（how to install operating system）
Boot device Priority Setting.If user will install operating system, please put“Boot Option #1”set to your CD-ROM or
your USB device, After setting, press "F10" key to save and exit,System boot from CD-ROM or U disk.
4.Copyright Notice
Copyright
This motherboard manual belongs to Colorful Technology and Development CO, LTD. No one is permitted to copy,
change, or translate without our written permission.
Disclaimer
The products name we mentioned in this manual is only for identifying, all of the brands belong to other company.
The registered trademarks of IBM, VGA and PS/2 belong to International Business Machines.
The registered trademarks of Intel, Pentium, Pentium Ⅱ, Celeron, Pentium III and Pentium 4 belong to Intel.
The registered trademark of Athlon belongs to Advanced Micro Devices, Inc.
The registered trademarks of Microsoft, MS-DOS, Windows 95/98/NT, Windows2000/XP etc. belong to Microsoft.
All of the trademarks in this manual have been registered.

Trademarks

5.Technical Support