BODY & TRIM GI

BT
MA

EM
SECTION
LC
MODIFICATION NOTICE:
I The instrument panel has been changed. EC
I The body side trim has been changed.
I The headlining has been changed.
I A jump seat has been added. FE
I An auto reverse function has been added to the driver’s door window.

CL
CONTENTS MT
PRECAUTIONS ...............................................................2 INTERIOR TRIM ..............................................................7
Supplemental Restraint System (SRS) ″AIR Side and Floor Trim .....................................................7 AT
BAG″ and ″SEAT BELT PRE-TENSIONER″...............2 Roof Trim ...................................................................10
DOOR...............................................................................3 SEAT ..............................................................................12
Front Door Limit Switch Reset (Driver side only)........3 Jump Seat - King Cab Model ....................................12 TF
INSTRUMENT PANEL.....................................................4

PD

FA

RA

BR

ST

RS

HA

EL

IDX

BT-1
 PRECAUTIONS

Supplemental Restraint System (SRS) “AIR

BAG” and “SEAT BELT PRE-TENSIONER”
The Supplemental Restraint System such as “AIR BAG” and “SEAT BELT PRE-TENSIONER” used along with
a seat belt, helps to reduce the risk or severity of injury to the driver and front passenger in a frontal collision.
The SRS system composition which is available to NISSAN MODEL D22 is as follows (The composition var-
ies according to the destination and optional equipment.):
Driver air bag module (located in the center of the steering wheel), front passenger air bag module (located
on the instrument panel on passenger side), seat belt pre-tensioner, a diagnosis sensor unit, warning lamp,
wiring harness and spiral cable.
Information necessary to service the system safely is included in the RS section of this Service Manual.
WARNING:
I To avoid rendering the SRS inoperative, which could increase the risk of personal injury or death
in the event of a collision which would result in air bag inflation, all maintenance must be performed
by an authorized NISSAN dealer.
I Improper maintenance, including incorrect removal and installation of the SRS, can lead to per-
sonal injury caused by unintentional activation of the system. For removal of Spiral Cable and Air
Bag Module, see the RS section.
I Do not use electrical test equipment on any circuit related to the SRS unless instructed to in this
Service Manual. Spiral Cable and wiring harnesses (except “SEAT BELT PRE-TENSIONER”) cov-
ered with yellow insulation either just before the harness connectors or for the complete harness
are related to the SRS.

BT-2
 DOOR

Front Door Limit Switch Reset (Driver side

only) GI
RESET CONDITIONS
After each of the following operations are performed, reset the limit MA
switch (with built-in motor).
I Regulator removal and installation
I Removal of motor from regulator EM
I Operation of regulator as a single unit
I Door glass removal and installation
I Glass run removal and installation LC
RESET PROCEDURES
After installing parts, proceed as follows: EC
1. Close the door window completely.
2. Press the reset switch and open the door window completely.
3. Release the reset switch. After making sure the reset switch FE
has returned to the original position, close the door window
completely.
4. The limit switch is now reset. CL
CAUTION:
Be sure to manually open or close the door window. (Do not
use the automatic open-close procedures.) MT
SBT845

AT

TF

PD

FA

RA

BR

ST

RS

HA

EL

IDX

BT-3
 INSTRUMENT PANEL

CAUTION:
I Disconnect both terminals from battery in advance.
I Disconnect air bag module connector in advance.
I Be careful not to scratch finishers and other parts.
I Never tamper with or force air bag lid open, as this may adversely affect air bag performance.
REMOVAL — Instrument panel assembly
Instrument panel assembly Combination meter Audio control Heater and A/C control

Remove driver’s air bag module and steering wheel. Tilt steering column down
Refer to “SUPPLEMENTAL RESTRAINT SYSTEM” in RS fully
section for details.

q
1 Steering column cover
I Remove screws.

q
2 Instrument lower panel driver side.
I Remove screws and bolts.

q
3 Cluster lid A
I Remove screws.

q
4 Combination meter
I Remove screws, then disconnect harness connectors.

q
5 Glove box assembly
I Remove screws.
I Then disconnect passenger air bag module connec-
tor.
I Then remove passenger air bag module bracket.
Refer to “SUPPLEMENTAL RESTRAINT SYSTEM” in
RS section for details.

q
6 Remove ashtray.

q
7 Cluster lid C
I Remove screws, then disconnect harness connectors.

q
8 Audio and deck pocket
I Remove screws, then disconnect harness connectors.

q
9 Heater and A/C control
I Disconnect temperature control cable and harness connectors.

q
10 Instrument stay cover lower center
I Remove screws.

q
11 Ventilator grille driver side

q
12 Defroster grille

Remove front pillar garnish.

Refer to “Side and Floor Trim” in “INTERIOR TRIM” for
details, BT-7.

q
13 Instrument panel assembly
I Remove screws and bolts.

q
14 Air duct passenger side
I Remove screws.

q
15 Passenger air bag module
I Refer to “SUPPLEMENTAL RESTRAINT SYSTEM” in
RS section for details.

BT-4
INSTRUMENT PANEL

GI

MA

EM

LC

EC

FE

CL

MT

AT

TF

PD

FA

RA

BR

ST

RS

HA

EL

IDX

SBT830

BT-5
INSTRUMENT PANEL

SBT831

BT-6
 INTERIOR TRIM

Side and Floor Trim

CAUTION: GI
Wrap the tip of flat-bladed screwdriver with a cloth when removing metal clips from garnishes.
REMOVAL — Body side trim MA
q
1 Remove front and rear seats. Refer to “SEAT” for details, in BT section of Service Manual Pub. No.
SM7E-0D22G1.
q
2 Remove front and rear seat belts. Refer to “SEAT BELTS” in RS section details. EM
q
3 Remove front and rear kicking plate.
q
4 Remove dash side lower finishers.
q
5 Remove front and rear body side welts. LC
q
6 Remove front pillar garnishes.
q
7 Remove center pillar lower garnishes.
q
8 Remove center pillar upper garnishes.
EC
q
9 Remove lock pillar garnishes.
FE

CL

MT

AT

TF

PD

FA

RA

BR

ST

RS

HA

EL

IDX

BT-7
INTERIOR TRIM
Side and Floor Trim (Cont’d)

SBT832

BT-8
INTERIOR TRIM
Side and Floor Trim (Cont’d)

GI

MA

EM

LC

EC

FE

CL

MT

AT

TF

PD

FA

RA

BR

ST

RS

HA

EL

IDX

SBT833

BT-9
 INTERIOR TRIM

Roof Trim
REMOVAL — Headlining
q
1 Remove front and rear seats. Refer to “SEAT” for details, in BT section of Service Manual Pub. No.
SM7E-0D22G1.
q
2 Remove front and rear seat belts. Refer to “SEAT BELTS” in RS section for details.
q
3 Remove body side trim. Refer to “Side and Floor Trim” for details, BT-7.
q
4 Remove sun visors.
q
5 Remove spot lamp assembly.
q
6 Remove inside mirror assembly.
q
7 Remove interior lamp assembly.
q
8 Remove assist grips.
q
9 Remove rear window weatherstrip and remove rear window glass.
q
10 Remove clips, then remove headlining.

SBT834

BT-10
INTERIOR TRIM
Roof Trim (Cont’d)

GI

MA

EM

LC

EC

FE

CL

MT

AT

TF

PD

FA

RA

BR

ST

RS

HA

EL

IDX

SBT835

BT-11
 SEAT

Jump Seat — King Cab Model

SBT836

BT-12