ACCELERATOR CONTROL, FUEL &

EXHAUST SYSTEMS GI

SECTION FE MA

EM

LC

EC

CONTENTS
PREPARATION ...............................................................2 FUEL SYSTEM ................................................................4
CL
Special Service Tool ....................................................2 Removal and Installation .............................................4
Commercial Service Tool.............................................2 FUEL TANK ...............................................................5 MT
ACCELERATOR CONTROL SYSTEM ...........................3 FUEL PUMP AND GAUGE .........................................6
Removal and Installation .............................................3 EXHAUST SYSTEM ........................................................8
Adjusting Accelerator Wire ..........................................3 Removal and Installation .............................................8 AT

TF

PD

AX

SU

BR

ST

RS

BT

HA

SC

EL

IDX
 PREPARATION
Special Service Tool

Special Service Tool NGFE0001

The actual shapes of Kent-Moore tools may differ from those of special service tools illustrated here.

Tool number
(Kent-Moore No.) Description
Tool name

KV10114400 (J38365) Loosening or tightening rear heated oxy-

Heated oxygen sensor gen sensor
wrench a: 22 mm (0.87 in)

NT636

Commercial Service Tool NGFE0007

Tool name Description

(J-43897-18) Reconditioning the exhaust system

(J-43897-12) threads before installing a new oxygen
Oxygen sensor thread sensor. Use with anti-seize lubricant
cleaner shown in Commercial Service Tools.
a: J-43897-18 18mm diameter, for Zir-
conia Oxygen Sensor
b: J-43897-12 12mm diameter, for Tita-
nia Oxygen Sensor

AEM488

Anti-seize lubricant Lubricating oxygen sensor thread cleaning

Permatex 133AR or tool when reconditioning exhaust system
equivalent meeting MIL threads.
specification MIL-A-907

AEM489

FE-2
 ACCELERATOR CONTROL SYSTEM
Removal and Installation

Removal and Installation NGFE0002

CAUTION:
When removing accelerator wire, make a mark to indicate lock nuts initial position. GI
Check that throttle valve opens fully when accelerator pedal is fully depressed. Also check that it
returns to idle position when pedal is released.
MA
Check accelerator control parts for improper contact with any adjacent parts.
When connecting accelerator wire, be careful not to twist or scratch its inner wire.
Refer to EL-170 (AUTOMATIC SPEED CONTROL DEVICE) for ASCD wire adjustment. EM

LC

EC

CL

MT

AT

AFE090 TF

PD

AX

Adjusting Accelerator Wire NGFE0003 SU

NOTE:
Adjust accelerator wire with the engine warmed up to normal
operating temperature and ignition switch turned to OFF. BR
1. Loosen lock nut, and tighten adjusting nut until throttle drum
starts to move.
2. From that position, turn back adjusting nut 1.5 to 2 turns, and ST
secure lock nut.
RS
SFE249AE

BT

HA

SC

EL

IDX
FE-3
 FUEL SYSTEM
Removal and Installation

Removal and Installation NGFE0004

WARNING:
When replacing fuel line parts, be sure to observe the follow-
ing:
Put a CAUTION: INFLAMMABLE sign in workshop.
Do not smoke while servicing fuel system. Keep open
flames and sparks away from work area.
Be sure to furnish the workshop with a CO2 fire extin-
guisher.
CAUTION:
Before removing fuel line parts, carry out the following
procedures:
a) Put drained fuel in an explosion-proof container and put
lid on securely.
b) Release fuel pressure from fuel line. Refer to MA-20
(KA24DE engine) or MA-29 (VG33E engine) (Changing
Fuel Filter).
c) Disconnect battery ground cable.
Always replace O-ring with a new one.
Do not kink or twist hoses and tubes when installed.
Do not tighten hose clamps excessively to avoid damag-
ing hoses.
When installing fuel check valve, be careful of its desig-
nated direction. Refer to EC-34 (EVAPORATIVE EMISSION
SYSTEM).
After installation, run engine and check for fuel leaks at
connections.

AFE131

FE-4
 FUEL SYSTEM
Removal and Installation (Contd)
FUEL TANK NGFE0004S01
1. Release fuel pressure from fuel line.
Refer to MA-20 (KA24DE engine) or MA-29 (VG33E engine) GI
(Changing Fuel Filter).
2. Disconnect battery ground cable.
3. Remove back seat bottom. Refer to BT-38.
MA
4. Remove inspection hole cover located under rear seat.
5. Drain fuel from fuel tank. EM
6. Disconnect electrical connectors.
7. Remove filler protector.
AFE123 LC
8. Remove the quick connectors as follows.
1) Put mating marks on the connectors for correct installation.
EC
2) Hold the sides of the connector, push in tabs, and pull out the
tube inserted in the retainer.
CAUTION:
The tube can be removed when the push in tabs are com-
pletely depressed. Do not use any tolls to remove the quick
connector. CL

AFE108
MT
9. Disconnect filler hose, vent and evaporation hose at fuel tank
side. AT

TF

PD

AX
SFE421A

10. Remove fuel tank protector.

SU

BR

ST

RS
AFE096

11. Remove fuel tank mounting bolts while supporting fuel tank. BT
12. Remove fuel tank.

HA

SC

EL
SFE423A
IDX
FE-5
 FUEL SYSTEM
Removal and Installation (Contd)
To install, reverse the removal procedure. Connect the quick con-
nectors as follows.
Align push in tabs with retainer openings.
Insert tube into the center of the connector until you hear a
click.

AFE110

After connecting quick connectors, make sure the connection is

firmly made using the following method.
Pull on the fuel tube and connector to make sure they are firmly
connected.
Start the engine, increase engine speed and verify that there
are no leaks.

AFE109

FUEL PUMP AND GAUGE NGFE0004S02

AFE132

FE-6
 FUEL SYSTEM
Removal and Installation (Contd)
1. Remove fuel tank. Refer to FUEL TANK, FE-5.
For removal of quick connectors, refer to step 6 of FUEL
TANK, FE-5. GI
2. Remove the six screws.
3. Remove fuel level sensor retainer and fuel level sensor.
4. Remove fuel pump with bracket while lifting the pawl of the fuel
MA
pump bracket upward.
EM

SFE425A LC
5. Remove fuel level sensor assembly.
Installation procedure is the reverse order of removal. EC
Install fuel level sensor as shown.
CAUTION:
Tighten bolts to specified torque.
: 2.0 - 2.5 Nm (0.20 - 0.26 kg-m, 17.4 - 22.6 in-lb)
Always replace O-ring with a new one.
CL
After installation, run engine and check for leaks at connec-
tions.
AFE095
MT

AT

TF

PD

AX

SU

BR

ST

RS

BT

HA

SC

EL

IDX
FE-7
 EXHAUST SYSTEM
Removal and Installation

Removal and Installation NGFE0005

CAUTION:
Always replace exhaust gaskets with new ones when reassembling.
With engine running, check all tube connections for exhaust gas leaks, and entire system for
unusual noises.
Check to ensure that mounting brackets and mounting insulators are installed properly and free
from undue stress. Improper installation could result in excessive noise or vibration.
Discard any heated oxygen sensor which has been dropped from a height of more than 0.5 m (19.7
in) onto a hard surface such as a concrete floor; use a new one.
Do not overtorque the oxygen sensor. Doing so may cause damage to the oxygen sensor, result-
ing in the MIL coming on.

FE-8
 EXHAUST SYSTEM
Removal and Installation (Contd)
KA24DE Models

GI

MA

EM

LC

EC

CL

MT

AT

TF

PD

AX

SU

BR

ST

RS

BT

HA

SC

AFE122 EL

IDX
FE-9
 EXHAUST SYSTEM
Removal and Installation (Contd)
VG33E Models

AFE129

1. Gasket- 4. Gasket 7. Mounting bracket

2. Front tube 5. Mounting rubber 8. Center muffler
3. Rear heated oxygen sensor 6. Clamp 9. Rear muffler

FE-10
 EXHAUST SYSTEM
Removal and Installation (Contd)
VG33E Models

GI

MA

EM

LC

EC

CL

MT

AT

TF

PD

AX

SU

BR

ST
AFE099
RS
1. Gasket 4. Gasket 7. Mounting bracket
2. Front tube 5. Mounting rubber 8. Center muffler
3. Rear heated oxygen sensor 6. Clamp 9. Rear muffler
BT

HA

SC

EL

IDX
FE-11
NOTES