Omm D8GC

3/27/23, 7:08 PM SIS 2.
2022/03/28 Maintenance Interval Schedule (M0131047-01)
SMCS - 7000 i08778917

Ensure that all safety information, warnings, and instructions are read and understood
PC
before any operation or any maintenance procedures are performed.
P-0
The user is responsible for the performance of maintenance. All adjustments, the use of proper
202 00
lubricants, fluids, filters, and the replacement of components due to normal wear and aging are
3 3
02: /03/2 785E
included. Failure to adhere to proper maintenance intervals and procedures may result in diminished
performance of the product and/or accelerated wear of components.
0
M0 8:21- 8
Use mileage, fuel consumption, service hours, or calendar time, WHICH EVER OCCURS FIRST, to
determine the maintenance intervals. Products that operate in severe operating conditions may require
1 3
© 2 104 7:00 0
more frequent maintenance. Refer to the maintenance procedure for any other exceptions that may
change the maintenance intervals.
023 7
Note: The aftertreatment system can be expected to function properly for the useful life of the engine
Cat
(emissions durability period), as defined by regulation. All prescribed maintenance requirements must
be followed.
erp
illa
Note: Before each consecutive interval is performed, all maintenance from the previous interval must
be performed.
r In
c.
The following guidelines should be followed if the service hours are not met:
Items listed between 10 and 100 service hours should be performed at least every 3 months.
Items listed between 250 and 500 service hours should be performed at least every 6 months.
Items listed between 1000 service hours and 2500 service hours should be performed at least every
year.
When Required
Battery, Battery Cable or Battery Disconnect Switch - Replace
Bottom Guards - Clean
Cooling System Water Temperature Regulator - Replace
Cutting Edges and End Bits - Inspect/Replace
Engine Air Filter Primary Element - Clean/Replace
Engine Air Filter Secondary Element - Replace
Engine Air Precleaner - Clean
Engine Crankcase Breather - Clean
Ether Starting Aid Cylinder - Replace
https://sis2.cat.com/#/print-preview/service/%257B%2522title%2522%253A%2522Maintenance%2520Interval%2520Schedule%2520(M0131047-01)… 1/4
3/27/23, 7:08 PM SIS 2.0
Fuel System - Prime

Fuel Tank Cap Filter and Strainer - Replace/Clean
Fuses and Circuit Breakers - Replace/Reset
Oil Filter - Inspect
Radiator Core - Clean
Radiator Pressure Cap - Clean/Replace
Ripper Tip and Shank Protector - Inspect/Replace
Winch Wire Rope - Install
Window Washer Reservoir - Fill
Window Wipers - Inspect/Replace
Windows - Clean
Every 10 Service Hours or Daily

Air Filter Restriction Indicator - Check
Backup Alarm - Test
Braking System - Test
Cab Filter (Fresh Air) - Clean/Inspect/Replace
Cooling System Level - Check
Engine Oil Level - Check
Fuel System Primary Filter (Water Separator) - Drain
Horn - Test
Hydraulic System Oil Level - Check
Indicators and Gauges - Test
Pivot Shaft Oil Level - Check
Seat Belt - Inspect
Transmission System Oil Level - Check
Every 50 Service Hours

Cab Filter (Recirculation) - Clean/Inspect/Replace
Ripper Linkage and Cylinder Bearings - Lubricate
Track Pins - Inspect

Air Conditioner Belt - Inspect/Adjust/Replace
Alternator and Fan Belts - Inspect/Adjust/Replace
Coolant Sample (DEAC) - Obtain
Cooling System (DEAC) Additive - Add
Engine Oil Sample - Obtain
Equalizer Bar End Pins Oil Level - Check
3/27/23, 7:08 PM SIS 2.0
Fan Drive Pulley and Idler - Lubricate

Final Drive Oil Level - Check
Fuel Tank Water and Sediment - Drain
Track - Check/Adjust
Winch Fairlead Rollers - Lubricate
Winch Oil Level - Check
Initial 500 Service Hours

Winch Oil and Breather - Change/Clean
Initial 500 Hours (for New Systems, Refilled Systems, and

Converted Systems)
Coolant Sample (Level 2) - Obtain

Engine Oil and Filter - Change
Final Drive Seal Guard - Inspect/Clean
Fuel System Primary Filter - Clean/Replace
Fuel System Secondary Filter - Replace
Hydraulic System Oil Sample - Obtain
Recoil Spring Compartment Oil Level - Check
Transmission System Oil Sample - Obtain
Winch Filter and Magnetic Strainer (57H) - Replace/Clean
Initial 1000 Service Hours

Engine Valve Lash - Adjust
Engine Valve Rotators - Inspect

Battery - Inspect
Hydraulic System Oil Filters - Replace
Lift Cylinder Yoke Bearings - Lubricate
Rollover Protective Structure (ROPS) and Falling Object Protective Structure (FOPS) - Inspect
Transmission Breather - Clean
Transmission Oil and Screen - Change/Clean
Transmission System Oil Filter - Replace
Winch Oil and Breather - Change/Clean
3/27/23, 7:08 PM SIS 2.0

Engine Air Filter Primary Element - Replace
Engine Air Filter Secondary Element - Replace
Engine Mounts and Equalizer Bar - Inspect
Final Drive Oil - Change
Radiator Guard Pin Joint - Inspect
Refrigerant Dryer - Replace
Track Roller Frame Guides - Inspect

Cooling System (DEAC) Coolant - Change
Engine Valve Lash - Adjust
Engine Valve Rotators - Inspect
Every 3 Years
Seat Belt - Replace

Cooling System (ELC) Extender - Add
Hydraulic System Oil - Change
Every 12 000 Service Hours

Cooling System (ELC) Coolant - Change
PCP-0003785E
2023/03/28
02:08:18-07:00
i08699252
© 2023 Caterpillar Inc.

Omm D8GC

Uploaded by

Copyright:

Available Formats

Omm D8GC

Uploaded by

Document Information

Original Title

Copyright

Available Formats

Share this document

Share or Embed Document

Sharing Options

Did you find this document useful?

Is this content inappropriate?

Copyright:

Available Formats

Omm D8GC

Uploaded by

Copyright:

Available Formats

3/27/23, 7:08 PM SIS 2.

2022/03/28 Maintenance Interval Schedule (M0131047-01)

SMCS - 7000 i08778917

Fuel System - Prime

Every 10 Service Hours or Daily

Every 50 Service Hours

Every 250 Service Hours

Fan Drive Pulley and Idler - Lubricate

Initial 500 Service Hours

Initial 500 Hours (for New Systems, Refilled Systems, and

Every 500 Service Hours

Initial 1000 Service Hours

Every 1000 Service Hours

Every 2000 Service Hours

Every 3000 Service Hours

Every 6000 Service Hours

Every 12 000 Service Hours

You might also like