DATA SHEET FOR VALVE

Document No. Rev. : A

DED EXPANSION NICKEL HEAP
Page:
BMR-PIP-DTS-ST-0001 LEACH 5,000 T/Y
Page 1 of 5

CLIENT : PT. BUKIT MAKMUR RESOURCES

CONSULTANT : PT. SIKO TECHNO
PROJECT NAME : DED EXPANSION NICKEL HEAP LEACH 5,000 T/Y
LOCATION : KABAENA ISLAND, SOUTH- EAST SULAWESI, INDONESIA
CONTRACT NO. : BMR/PRC/2022/VI/048/SKLR

A 09/09/2022 IFA AG VAN YYT

PREPARED BY CHECKED BY REVIEWED BY APPROVED BY

PT. BUKIT MAKMUR

Rev DATE DESCRIPTION PT. SIKO TECHNO RESOURCES
 DATA SHEET FOR VALVE

Document No. Rev. : A

DED EXPANSION NICKEL HEAP
Page:
BMR-PIP-DTS-ST-0001 LEACH 5,000 T/Y
Page 2 of 5

REVISION SHEET

REV DATE DESCRIPTION

 DATA SHEET FOR VALVE

Document No. Rev. : A

DED EXPANSION NICKEL HEAP
Page:
BMR-PIP-DTS-ST-0001 LEACH 5,000 T/Y
Page 3 of 5

TABLE OF CONTENT

SCOPE .......................................................................................................................................................... 4
REFERENCE ................................................................................................................................................ 4
2.1 Codes ...................................................................................................................................................... 4
2.2 Standard and Specification ...................................................................................................................... 4
2.3 General .................................................................................................................................................... 4
2.4 Line Numbering ....................................................................................................................................... 5
ATTACHMENT DATA SHEET VALVE ......................................................................................................... 5
 DATA SHEET FOR VALVE

Document No. Rev. : A

DED EXPANSION NICKEL HEAP
Page:
BMR-PIP-DTS-ST-0001 LEACH 5,000 T/Y
Page 4 of 5

SCOPE

The purpose of this Data sheet is for providing guidelines during field application works of selection
valve to be executed for project DED EXPANSION NICKEL HEAP LEACH 5.000 T/Y.
The CONTRACTOR shall ensure that all equipment and services supplied meet the requirements
of this specification, and the codes, standards and specifications nominated herein, and shall be
applies to the following project :

Client : PT. Bukit Makmur Resources

Consultant : PT. Siko Techno
Project Name : DED Expansion Nickel Heap Leach 5,000 T/Y
Location : Kabaena Island, South East Sulawesi, Indonesia
Contract No : BMR/PRC/2022/VI/048/SKLR

REFERENCE

The latest edition of following publications shall be considered as an integral part of this
specification. If there are any conflicts between these codes and other related documents,
the more stringent requirement shall govern.

2.1 Codes

Applicable code for this project accordance with ASME B31.3 Process Piping.

2.2 Standard and Specification

ASME American Society of Mechanical Engineer

JIS Japanese Industrial Standard
ASTM American Society for Testing and Materials
NFPA National Fire Protection Association
ISO International Organization for Standardization
BS British Standard

2.3 General

a. Process & Instrument Diagram (P&ID)

The Piping shall be design as per P&ID and PFD
b. Piping Design
The metric system for dimensioning shall be adopted throughout this project. Pipe sizes
shall however be expressed in inches. And all design requirements must comply with this
document.
 DATA SHEET FOR VALVE

Document No. Rev. : A

DED EXPANSION NICKEL HEAP
Page:
BMR-PIP-DTS-ST-0001 LEACH 5,000 T/Y
Page 5 of 5

2.4 Line Numbering

The pipe line numbering system shall be formatted as per stated on P&ID.

ATTACHMENT DATA SHEET VALVE

 Attachment 1 Data Sheet Ball Valve

 Attachment 2 Data Sheet Butterfly Valve
 Attachment 3 Data Sheet Check Valve
 Attachment 4 Data Sheet Gate Valve
 Attachment 5 Data Sheet Globe Valve
DATA SHEET FOR VALVES
BMR-PIP-DTS-ST-0001 Rev. A
DED EXPANSION NICKEL HEAP LEACH 5,000 T/Y

ATTACHMENT - 1
Data Sheet Ball Valve
 Client : Contractor :

DED EXPANSION NICKEL HEAP LEACH 5,000 T/Y

Doc. No
DATA SHEET FOR BALL VALVE Page Rev.
BMR-PIP-DTS-ST-0001
1 of 2 A

LINE CLASS 5K - 20K

1 Valve Type : BALL VALVE PARTS DESCRIPTION AND MATERIAL LIST :

2 JIS Class : 800# 1 Body : A105

3 Size Range : 1/2" - 1-1/2" 2 Stem : A 479 316

4 Material : CARBON STEEL 3 Hand Lever : MANUFACTURER STANDARD

5 Material Class/Line Class : 5K - 20K 4 Seat Ring : NYLON / PTFE

5 Name Plate : MANUFACTURER STANDARD

6 Ball : A 479 316

VALVE DESIGN : 7 Packing : FLEXIBLE GRAPHITE

1 Design Code : MSS SP 110 / BS 5351 / MANUFACTURER STANDARD 8 Bolt : A193 - B7

2 Pressure-Temp. Rating : BS 5351 9 Nut : A194 - 2H

(6)
3 End Connection : SW X SW / SW x FNPT / FNPT X FNPT (ASME B16.11 & B1.20.1)

4 Face to Face Dimension : MANUFACTURER STANDARD

5 Body Configuration : BOLTED BODY, FLOATING, THREE PIECES BODY, ANTI BLOWOUT

: FORGED STEEL CONSTRUCTION, ANTI STATIC DEVICE

6 Port Type : FULL PORT

7 Valve Operation : MANUAL LEVER OPERATED

8 Fire Test : MANUFACTURER STANDARD

9 Service : ACID, FIRE WATER, STEAM, GASES, OIL, WATER, SEA WATER

TECHNICAL DELIVERY REQUIREMENTS :

1 Inspection and Testing : JIS B2003

2 Visual Inspection : JIS B2003 / MSS SP-55

3 Marking : MSS SP-25 / JIS B2004

4 Documentation : ASSEMBLY DRAWING

MILL CERTIFICATE

CERTIFICATE OF COMPLIANCE

PRESSURE TEST REPORT

5 Certification : BS EN 10204 3.1 / 3.2

6 Painting : -

NOTES :

1 ALL VALVES SHALL BE SUPPLIED IN ACCORDANCE WITH THE APPLICABLE ASME CODES & STANDARD STATED IN THIS DOCUMENT

2 IN ADDITION TO THE NAME PLATES. EACH VALVE SHALL BE SUPPLIED WITH 316SS VALVE TAG STAMP SECURELY FIXED TO THE VALVE WITH 316SS WIRE

3 TEST DURATION AND LEAKAGE RATES SHALL BE IN ACCORDANCE WITH JIS 2003

4 GASKET / PACKING SHALL BE SUITABLE FOR THE SERVICE AND DESIGN CONDITIONS AS STATED ABOVE

5 TAGGING VALVE NUMBER REFER TO P&ID

6 IN ADDITION TO. EACH SW CONNECTION SHOULD BE EQUIPED PIPE NIPPLE WITH 3" LENGTH

7 IF THERE ARE DIFFERENCES IN MATERIAL SPECIFICATIONSOF PARTS, VENDORS MUST ENSURE THE QUALITY OF THE PARTS MUST BE EQUIVALENT OR ABOVE

8 ALL OTHER ITEMS NOT MENTIONED IN THE MATERIAL LIST ABOVE, AS PER MANUFACTURING STANDARDS
 Client : Contractor :

DED EXPANSION NICKEL HEAP LEACH 5,000 T/Y

Doc. No
DATA SHEET FOR BALL VALVE Page Rev.
BMR-PIP-DTS-ST-0001
2 of 2 A

LINE CLASS 5K - 20K

1 Valve Type : BALL VALVE

2 JIS Class : 5K - 20K

3 Size Range : 2" - 24"

4 Material : CARBON STEEL PARTS DESCRIPTION AND MATERIAL LIST :

5 Material Class/Line Class : LINE CLASS 5K - 20K 1 Body : A216 WCB

2 Ball : A182 F304

3 Stem : A182 F304

4 Body Bolts : A193 - B7

5 Body Nuts : A194 - 2H

VALVE DESIGN : 6 Seat Ring : RPTFE / NYLON

1 Design Code : JIS B2071 & B2081 7 Body Gasket : 304SS + GRAPHITE

2 Pressure-Temp. Rating : JIS B2071 & B2081 8 Gland : A182 F304

3 End Connection : RF x RF AS PER JIS B2002 9 O Ring : VITON

4 End-to-End Dimension : JIS B2002 10 Handwheel / Gear Operation : MANUFACTURER STANDARD

5 Body Configuration : BOLTED BODY, ANTI STATIC DEVICE

6 Port Type : FULL BORE

(Note 6)
7 Valve Operator : LEVER OPERATED / GEAR OPERATED

8 Fire Test : MANUFACTURER STANDARD

(7)
9 Body Design Type : FLOATING / TRUNION

TECHNICAL DELIVERY REQUIREMENTS :

1 Inspection and Testing : JIS B2003

2 Visual Inspection : JIS B2003 / MSS SP-55

3 Marking : MSS SP-25 / JIS B2004

4 Fabrication Welding : JIS B 8285

5 Documentation : ASSEMBLY DRAWING, MILL CERTIFICATE,

CERTIFICATE OF COMPLIANCE, FIRE TEST CERTIFICATED

PRESSURE TEST REPORT: HYDRO AND PNEUMATIC TEST

6 Certification : BS EN 10204 3.1 / 3.2

7 Painting : REFER TO DOC. BMR-QAC-PRC-ST-0002

PAINTING PROCEDURE

8 Service : ACID, FIRE WATER, STEAM, GASES, OIL, WATER, SEA WATER

NOTES :

1 ALL VALVES SHALL BE SUPPLIED IN ACCORDANCE WITH THE APPLICABLE ASME CODES & STANDARD STATED IN THIS DOCUMENT

2 IN ADDITION TO THE NAME PLATES, EACH VALVE SHALL BE SUPPLIED WITH 316SS VALVE TAG STAMP SECURELY FIXED TO THE VALVE WITH 316SS WIRE

3 TEST DURATION AND LEAKAGE RATES SHALL BE IN ACCORDANCE WITH JIS B2003

4 GASKET / PACKING SHALL BE SUITABLE FOR THE SERVICE AND DESIGN CONDITIONS AS STATED ABOVE

5 TAGGING VALVE NUMBER REFER TO P&ID

6 LEVER OPEARTION USED FOR SIZE 2" - 4" AND GEAR OPEARTION USED 6" ABOVE

7 FLOATING DESIGN USED FOR 2" - 4" AND TRUNION DESIGN USED FOR 6" ABOVE

8 IF THERE ARE DIFFERENCES IN MATERIAL SPECIFICATIONSOF PARTS, VENDORS MUST ENSURE THE QUALITY OF THE PARTS MUST BE EQUIVALENT OR ABOVE

9 ALL OTHER ITEMS NOT MENTIONED IN THE MATERIAL LIST ABOVE, AS PER MANUFACTURING STANDARDS
DATA SHEET FOR VALVES
BMR-PIP-DTS-ST-0001 Rev. A
DED EXPANSION NICKEL HEAP LEACH 5,000 T/Y

ATTACHMENT - 2
Data Sheet Butterfly Valve
 Client : Contractor :

DED EXPANSION NICKEL HEAP LEACH 5,000 T/Y

Doc. No
DATA SHEET FOR BUTTERFLY VALVE Page Rev.
BMR-PIP-DTS-ST-0001
1 of 1 A

LINE CLASS 5K - 20K

1 Valve Type : BUTTERFLY VALVE PARTS DESCRIPTION AND MATERIAL LIST :

2 ANSI Class : 5K - 20K 1 Body : A216 WCB

3 Size Range : 2" - 12" 2 Seat : VITON

4 Material : CARBON STEEL 3 Hand Wheel : MANUFACTURER STANDARD

5 Material Class/Line Class : 5K - 20K 4 Stem : A182 F304

5 O Ring : VITON

6 Disc : A182 F304

7 Bolt : A193 Gr. B7

VALVE DESIGN : 8 Nut : A194 Gr. 2H

1 Design Code : MANUFACTURER STANDARD

2 Pressure-Temp. Rating : JIS B2071 / JIS B2064

3 End Connection : RF x RF AS PER JIS B2002

4 Face to Face Dimension : JIS B2002

5 Body Configuration : FLANGED TYPE

8 Valve Operation : LEVER

9 Service : FIRE WATER, ACID, SEA WATER

10 Fire Test : MANUFACTURER STANDARD

TECHNICAL DELIVERY REQUIREMENTS :

1 Inspection and Testing : JIS B2003

2 Visual Inspection : JIS B2003 / MSS SP-55

3 Marking : MSS SP-25 / JIS B2004

4 Documentation : ASSEMBLY DRAWING

: MILL CERTIFICATE

: CERTIFICATE OF COMPLIANCE

: PRESSURE TEST REPORT

5 Certification : BS EN 10204 3.1 / 3.2

6 Painting : MANUFACTURER STANDARD

NOTES :

1 ALL VALVES SHALL BE SUPPLIED IN ACCORDANCE WITH THE APPLICABLE ASME CODES, ASTM STANDARDS, API STANDARDS AND PERTAMINA SPECIFICATIONS

2 IN ADDITION TO THE NAME PLATES, EACH VALVE SHALL BE SUPPLIED WITH 316SS VALVE TAG STAMP SECURELY FIXED TO THE VALVE WITH 316SS WIRE

3 TEST DURATION AND LEAKAGE RATES SHALL BE IN ACCORDANCE WITH JIS B2003

4 GASKET / PACKING SHALL BE SUITABLE FOR THE SERVICE AND DESIGN CONDITIONS AS STATED ABOVE

5 TAGGING VALVE NUMBER REFER TO P&ID

DATA SHEET FOR VALVES
BMR-PIP-DTS-ST-0001 Rev. A
DED EXPANSION NICKEL HEAP LEACH 5,000 T/Y

ATTACHMENT - 3
Data Sheet Check Valve
 Client : Contractor :

DED EXPANSION NICKEL HEAP LEACH 5,000 T/Y

Doc. No
DATA SHEET FOR CHECK VALVE Page Rev.
BMR-PIP-DTS-ST-0001
1 of 2 A

LINE CLASS 800#

1 Valve Type : CHECK VALVE

2 ANSI Class : CLASS 800#

3 Size Range : 1/2" - 1 1/2"

4 Material : CARBON STEEL

5 Material Class/Line Class : 5K - 20K PARTS DESCRIPTION AND MATERIAL LIST :

1 Pin : MANUFACTURER STANDARD

2 Bolts : A193 B7

3 Name Plate : MANUFACTURER STANDARD

VALVE DESIGN : 5 Cap : A105

1 Design Code : MSS SP 110 / BS 5351 / MANUFACTURER STANDARD 6 Gasket : FLEXIBLE GRAPHITE + SS WIRE

2 Pressure-Temp. Rating : BS 5351 7 Piston : A276 316

(6)
3 End Connection : SW X SW / SW x FNPT / FNPT X FNPT (ASME B16.11 & B1.20.1) 8 Seat : Int. + HF

4 End-to-End Dimension : MANUFACTURER STANDARD 9 Body : A105

5 Body Configuration : PISTON, BOLTED CAP 10 Disc Nut : A194 - 2H

11 Spring : AISI 316

6 Valve Operation : -

7 Service : ACID, FIRE WATER, STEAM, GASES, OIL, WATER, SEA WATER

TECHNICAL DELIVERY REQUIREMENTS :

1 Inspection and Testing : API 598 / API 6D

2 Visual Inspection : MSS SP-55

3 Marking : MSS SP-25

4 Documentation : ASSEMBLY DRAWING

: MILL CERTIFICATE

: CERTIFICATE OF COMPLIANCE

: PRESSURE TEST REPORT

5 Certification : BS EN 10204 3.1

6 Painting : -

NOTES :

1 ALL VALVES SHALL BE SUPPLIED IN ACCORDANCE WITH THE APPLICABLE ASME CODES & STANDARD STATED IN THIS DOCUMENT

2 IN ADDITION TO THE NAME PLATES, EACH VALVE SHALL BE SUPPLIED WITH 316SS VALVE TAG STAMP SECURELY FIXED TO THE VALVE WITH 316SS WIRE

3 TEST DURATION AND LEAKAGE RATES SHALL BE IN ACCORDANCE WITH JIS 2003

4 GASKET / PACKING SHALL BE SUITABLE FOR THE SERVICE AND DESIGN CONDITIONS AS STATED ABOVE

5 TAGGING VALVE NUMBER REFER TO P&ID

6 IF THERE ARE DIFFERENCES IN MATERIAL SPECIFICATIONSOF PARTS, VENDORS MUST ENSURE THE QUALITY OF THE PARTS MUST BE EQUIVALENT OR ABOVE

7 ALL OTHER ITEMS NOT MENTIONED IN THE MATERIAL LIST ABOVE, AS PER MANUFACTURING STANDARDS
 Client : Contractor :

DED EXPANSION NICKEL HEAP LEACH 5,000 T/Y

Doc. No
DATA SHEET FOR CHECK VALVE Page Rev.
BMR-PIP-DTS-ST-0001
2 of 2 A

LINE CLASS 5K - 20K

1 Valve Type : CHECK VALVE

2 JIS Class : 5K - 20K

3 Size Range : 2" - 24"

4 Material : CARBON STEEL

5 Material Class/Line Class : LINE CLASS 5K - 20K PARTS DESCRIPTION AND MATERIAL LIST :

1 Body : A216 WCB

2 Cover : A216 WCB

3 Disc : A216 WCB 13 % Cr

VALVE DESIGN : 4 Seat : A105 + Stellite

1 Design Code : JIS B2071 & B2081 5 Hinge : A216 WCB

2 Pressure-Temp. Rating : JIS B2071 & B2081 6 Hinge Pin : A182 F6a

3 End Connection : RF x RF AS PER JIS B2002 7 Gasket : SS304 + Graphite

4 End-to-End Dimension : JIS B2002 8 Cover Bolt : A193 - B7

5 Body Configuration : SWING TYPE 9 Cover Nut : A194 - 2H

: 10 Plug : A105

6 Valve Operation : -

7 Service : ACID, FIRE WATER, STEAM, GASES, OIL, WATER, SEA WATER

8 Fire Test : MANUFACTURER STANDARD

TECHNICAL DELIVERY REQUIREMENTS :

1 Inspection and Testing : JIS B2003

2 Visual Inspection : JIS B2003 / MSS SP-55

3 Marking : MSS SP-25 / JIS B2004

4 Documentation : ASSEMBLY DRAWING

: MILL CERTIFICATE

: CERTIFICATE OF COMPLIANCE

: PRESSURE TEST REPORT

5 Certification : BS EN 10204 3.1 / 3.2

6 Painting : REFER TO DOC. BMR-QAC-PRC-ST-0002

PAINTING PROCEDURE

NOTES :

1 ALL VALVES SHALL BE SUPPLIED IN ACCORDANCE WITH THE APPLICABLE ASME CODES & STANDARD STATED IN THIS DOCUMENT

2 IN ADDITION TO THE NAME PLATES, EACH VALVE SHALL BE SUPPLIED WITH 316SS VALVE TAG STAMP SECURELY FIXED TO THE VALVE WITH 316SS WIRE

3 TEST DURATION AND LEAKAGE RATES SHALL BE IN ACCORDANCE WITH JIS B2003

4 GASKET / PACKING SHALL BE SUITABLE FOR THE SERVICE AND DESIGN CONDITIONS AS STATED ABOVE

5 TAGGING VALVE NUMBER REFER TO P&ID

6 IF THERE ARE DIFFERENCES IN MATERIAL SPECIFICATIONSOF PARTS, VENDORS MUST ENSURE THE QUALITY OF THE PARTS MUST BE EQUIVALENT OR ABOVE

7 ALL OTHER ITEMS NOT MENTIONED IN THE MATERIAL LIST ABOVE, AS PER MANUFACTURING STANDARDS
DATA SHEET FOR VALVES
BMR-PIP-DTS-ST-0001 Rev. A
DED EXPANSION NICKEL HEAP LEACH 5,000 T/Y

ATTACHMENT - 4
Data Sheet Gate Valve
 Client Contractor

PALU MINING POWER PLANT 20 MW

Doc. No
DATA SHEET FOR GATE VALVE Page Rev.
BMR-PIP-DTS-ST-0001
1 of 2 A

LINE CLASS 5K - 20K

1 Valve Type : GATE VALVE PARTS DESCRIPTION AND MATERIAL LIST :

2 JIS Class : 800# 1 Body : ASTM A105

3 Size Range : 1/2" - 1 1/2" 2 Name plate : MANUFACTURER STANDARD

4 Material : CARBON STEEL 3 Hand Whell : MANUFACTURER STANDARD

5 Material Class/Line Class : LINE CLASS 5K - 20K 4 Stem : 410

5 Bonnet Bolt : A193 B7 + HOT DIP GALVANIZED

6 Bonnet : A105

VALVE DESIGN : 7 Gasket : FLEXIBLE GRAPHITE + SS WIRE

1 Design Code : MSS SP 110 / BS 5351 / MANUFACTURER STANDARD 8 Wedge : 410

2 Pressure-Temp. Rating : BS 5351 9 Seat Ring : 410 + STL

3 End Connection : SW X SW / SW x FNPT / FNPT X FNPT (ASME B16.11 & B1.20.1) 10 Gland Nut : A194-2H + HOT DIP GALVANIZED

4 Face to Face Dimension : MANUFACTURER STANDARD 11 Gland Flange : A105

5 Body Configuration : BOLTED BONNET, OS&Y, RISSING STEM

6 Disc Type : SOLID WEDGE

7 Bore Type : FULL

8 Valve Operation : MANUAL HANDWHEEL

9 Service : FIRE WATER, STEAM, GASES, OIL, WATER

10 Fire Test : MANUFACTURER STANDARD

TECHNICAL DELIVERY REQUIREMENTS :

1 Inspection and Testing : JIS B2003 / MANUFACTURER STANDARD

2 Visual Inspection : JIS B2003 / MSS SP-55

3 Marking : MSS SP-25 / JIS B2004

4 Documentation : ASSEMBLY DRAWING

: MILL CERTIFICATE

: CERTIFICATE OF COMPLIANCE

: PRESSURE TEST REPORT

5 Certification : BS EN 10204 3.1 / 3.2

6 Painting : -

NOTES :

1 ALL VALVES SHALL BE SUPPLIED IN ACCORDANCE WITH THE APPLICABLE ASME CODES & STANDARD STATED IN THIS DOCUMENT

2 IN ADDITION TO THE NAME PLATES, EACH VALVE SHALL BE SUPPLIED WITH 316SS VALVE TAG STAMP SECURELY FIXED TO THE VALVE WITH 316SS WIRE

3 TEST DURATION AND LEAKAGE RATES SHALL BE IN ACCORDANCE WITH JIS 2003

4 GASKET / PACKING SHALL BE SUITABLE FOR THE SERVICE AND DESIGN CONDITIONS AS STATED ABOVE

5 TAGGING VALVE NUMBER REFER TO P&ID

6 IF THERE ARE DIFFERENCES IN MATERIAL SPECIFICATIONSOF PARTS, VENDORS MUST ENSURE THE QUALITY OF THE PARTS MUST BE EQUIVALENT OR ABOVE

7 ALL OTHER ITEMS NOT MENTIONED IN THE MATERIAL LIST ABOVE, AS PER MANUFACTURING STANDARDS
 Client : Contractor :

DED EXPANSION NICKEL HEAP LEACH 5,000 T/Y

Doc. No
DATA SHEET FOR GATE VALVE Page Rev.
BMR-PIP-DTS-ST-0001
2 of 2 A

LINE CLASS 5K - 20K

1 Valve Type : GATE VALVE PARTS DESCRIPTION AND MATERIAL LIST :

2 JIS Class : 5K - 20K 1 Body : A216-WCB

3 Size Range : 2" - 24" 2 Bonnet : A216-WCB

4 Material : CARBON STEEL 3 Stem : A182 F6

5 Material Class/Line Class : LINE CLASS 5K - 20K 4 Disc / Wedge : A216 WCB + 13 % Cr

5 Seat : A105 + STELLITE

6 Hand Weel : MANUFACTURER STANDARD

VALVE DESIGN : 7 Packing : FLEXIBLE GRAPHITE

1 Design Code : JIS B2071 & B2081 8 Bonet Stud : A193-B7

2 Pressure-Temp. Rating : JIS B2071 & B2081 9 Bonet Nut : A194-2H

3 End Connection : RF x RF AS PER JIS B2002 10 Gland : A276 410

4 Face to Face Dimension : JIS B2002

5 Body Configuration : BOLTED BONNET, OS&Y, RISING STEM

6 Disc Type : FLEXIBLE WEDGE

7 Bore Type : FULL

Valve Operation (Note 6)

8 : HANDWHEEL / GEAR OPERATION

9 Service : ACID, FIRE WATER, STEAM, GASES, OIL, WATER, SEA WATER

10 Fire Test : MANUFACTURER STANDARD

TECHNICAL DELIVERY REQUIREMENTS :

1 Inspection and Testing : JIS B2003

2 Visual Inspection : JIS B2003 / MSS SP-55

3 Marking : MSS SP-25 / JIS B2004

4 Documentation : ASSEMBLY DRAWING

: MILL CERTIFICATE

: CERTIFICATE OF COMPLIANCE

: PRESSURE TEST REPORT

5 Certification : BS EN 10204 3.1 / 3.2

6 Painting : REFER TO DOC. BMR-QAC-PRC-ST-0002

PAINTING PROCEDURE

NOTES :

1 ALL VALVES SHALL BE SUPPLIED IN ACCORDANCE WITH THE APPLICABLE ASME CODES & STANDARD STATED IN THIS DOCUMENT

2 IN ADDITION TO THE NAME PLATES, EACH VALVE SHALL BE SUPPLIED WITH 316SS VALVE TAG STAMP SECURELY FIXED TO THE VALVE WITH 316SS WIRE

3 TEST DURATION AND LEAKAGE RATES SHALL BE IN ACCORDANCE WITH JIS B2003

4 GASKET / PACKING SHALL BE SUITABLE FOR THE SERVICE AND DESIGN CONDITIONS AS STATED ABOVE

5 TAGGING VALVE NUMBER REFER TO P&ID

6 MANUAL HANDWHEEL USED FOR SIZE 2" - 12 " AND GEAR OPEARTION USED 14" ABOVE

7 IF THERE ARE DIFFERENCES IN MATERIAL SPECIFICATIONSOF PARTS, VENDORS MUST ENSURE THE QUALITY OF THE PARTS MUST BE EQUIVALENT OR ABOVE

8 ALL OTHER ITEMS NOT MENTIONED IN THE MATERIAL LIST ABOVE, AS PER MANUFACTURING STANDARDS
DATA SHEET FOR VALVES
BMR-PIP-DTS-ST-0001 Rev. A
DED EXPANSION NICKEL HEAP LEACH 5,000 T/Y

ATTACHMENT - 5
Data Sheet Globe Valve
 Client : Contractor :

DED EXPANSION NICKEL HEAP LEACH 5,000 T/Y

Doc. No
DATA SHEET FOR GLOBE VALVE Page Rev.
BMR-PIP-DTS-ST-0001
1 of 2 A

LINE CLASS 5K - 20K

1 Valve Type : GLOBE VALVE PARTS DESCRIPTION AND MATERIAL LIST :

2 JIS Class : 800# 1 Body : A105

3 Size Range : 1/2" - 1-1/2" 2 Name Plate : MANUFACTURER STANDARD

4 Material : CARBON STEEL 3 Hand Wheel : MANUFACTURER STANDARD

5 Material Class/Line Class : CLASS 150# & 300# 4 Stem : A276 316

5 Bonnet : A105

6 Bonnet Bolts : A193-B7

7 Gasket : FLEXIBLE GRAPHITE

VALVE DESIGN : 8 Disc : A351 CF8M

1 Design Code : MSS SP 110 / BS 5351 / MANUFACTURER STANDARD 9 Seat : INTEGRAL HARDFACE STELLITE

2 Pressure-Temp. Rating : BS 5351 10 Gland Flange : A105

3 End Connection : SW X SW / SW x FNPT / FNPT X FNPT (ASME B16.11 & B1.20.1)

4 Face to Face Dimension : MANUFACTURER STANDARD

5 Body Configuration : BOLTED BONNET, OS&Y, RISING STEM

6 Disc Type : SOLID DISC

7 Bore Type : FULL

8 Valve Operation : MANUAL HANDWHEEL

9 Service : ACID, FIRE WATER, STEAM, GASES, OIL, WATER, SEA WATER

10 Fire Test : MANUFACTURER STANDARD

TECHNICAL DELIVERY REQUIREMENTS :

1 Inspection and Testing : JIS B2003 / MANUFACTURER STANDARD

2 Visual Inspection : JIS B2003 / MSS SP-55

3 Marking : MSS SP-25 / JIS B2004

4 Documentation : ASSEMBLY DRAWING

: MILL CERTIFICATE

: CERTIFICATE OF COMPLIANCE

: PRESSURE TEST REPORT

5 Certification : BS EN 10204 3.1 / 3.2

6 Painting : -

NOTES :

1 ALL VALVES SHALL BE SUPPLIED IN ACCORDANCE WITH THE APPLICABLE ASME CODES & STANDARD STATED IN THIS DOCUMENT

2 IN ADDITION TO THE NAME PLATES, EACH VALVE SHALL BE SUPPLIED WITH 316SS VALVE TAG STAMP SECURELY FIXED TO THE VALVE WITH 316SS WIRE

3 TEST DURATION AND LEAKAGE RATES SHALL BE IN ACCORDANCE WITH JIS 2003

4 GASKET / PACKING SHALL BE SUITABLE FOR THE SERVICE AND DESIGN CONDITIONS AS STATED ABOVE

5 TAGGING VALVE NUMBER REFER TO P&ID

6 IF THERE ARE DIFFERENCES IN MATERIAL SPECIFICATIONSOF PARTS, VENDORS MUST ENSURE THE QUALITY OF THE PARTS MUST BE EQUIVALENT OR ABOVE

7 ALL OTHER ITEMS NOT MENTIONED IN THE MATERIAL LIST ABOVE, AS PER MANUFACTURING STANDARDS
 Client : Contractor :

DED EXPANSION NICKEL HEAP LEACH 5,000 T/Y

Doc. No
DATA SHEET FOR GLOBE VALVE Page Rev.
BMR-PIP-DTS-ST-0001
2 of 2 A

LINE CLASS 5K - 20K

1 Valve Type : GLOBE VALVE PARTS DESCRIPTION AND MATERIAL LIST :

2 JIS Class : 5K - 20K 1 Body : ASTM A216-WCB

3 Size Range : 2" - 24" 2 Bonnet : ASTM A216-WCB

4 Material : CARBON STEEL 3 Stem : A182 F6

5 Material Class/Line Class : LINE CLASS 5K - 20K 4 Disc : A216 WCB + 13% Cr

5 Seat : A105 + SteLlite

6 Bonnet Bolt : A193-B7

7 Bonnet Nut : A194-2H

VALVE DESIGN : 8 Handwheel : MANUFACTURER STANDARD

1 Design Code : JIS B2071 & B2081 9 Gland : A2176 40

2 Pressure-Temp. Rating : JIS B2071 & B2081 10 Gasket : SS304 + GRAPHITE

3 End Connection : RF x RF AS PER JIS B2002

4 Face to Face Dimension : JIS B2002

5 Body Configuration : BOLTED BONNET, OS&Y, RISING STEM

6 Disc Type : CONICAL PLUG

7 Bore Type : FULL

Valve Operation (Note 6)

8 : HANDWHEEL / GEAR OPERATION

9 Service : ACID, FIRE WATER, STEAM, GASES, OIL, WATER, SEA WATER

10 Fire Test : MANUFACTURER STANDARD

TECHNICAL DELIVERY REQUIREMENTS :

1 Inspection and Testing : JIS B2071 & B2081

2 Visual Inspection : JIS B2071 & B2081

3 Marking : RF x RF AS PER JIS B2002

4 Documentation : JIS B2002

: MILL CERTIFICATE

: CERTIFICATE OF COMPLIANCE

: PRESSURE TEST REPORT

5 Certification : BS EN 10204 3.1 / 3.2

6 Painting : REFER TO DOC. BMR-QAC-PRC-ST-0002

PAINTING PROCEDURE

NOTES :

1 ALL VALVES SHALL BE SUPPLIED IN ACCORDANCE WITH THE APPLICABLE ASME CODES & STANDARD STATED IN THIS DOCUMENT

2 IN ADDITION TO THE NAME PLATES, EACH VALVE SHALL BE SUPPLIED WITH 316SS VALVE TAG STAMP SECURELY FIXED TO THE VALVE WITH 316SS WIRE

3 TEST DURATION AND LEAKAGE RATES SHALL BE IN ACCORDANCE WITH JIS B2003

4 GASKET / PACKING SHALL BE SUITABLE FOR THE SERVICE AND DESIGN CONDITIONS AS STATED ABOVE

5 TAGGING VALVE NUMBER REFER TO P&ID

6 MANUAL HANDWHEEL USED FOR SIZE 2" - 6 " AND GEAR OPEARTION USED 8" ABOVE

7 IF THERE ARE DIFFERENCES IN MATERIAL SPECIFICATIONSOF PARTS, VENDORS MUST ENSURE THE QUALITY OF THE PARTS MUST BE EQUIVALENT OR ABOVE

8 SEE APPENDIX 1 FOR TOP COAT & APPENDIX 2 FOR PAINTING SYSTEM (RECOMEND USING SP2)

9 ALL OTHER ITEMS NOT MENTIONED IN THE MATERIAL LIST ABOVE, AS PER MANUFACTURING STANDARDS