LINDE STANDARD

Oxygen Service
Visual Cleanliness Inspection Guide LS 141-76
Bright Light - UV Light
Page 1 of 73

Contents

1 Scope ................................................................2
2 Normative references ........................................2
3 Abbreviations and definitions ............................2
4 General..............................................................2
5 Cleanliness requirements..................................2
6 Visual Cleanliness Inspection Methods ............3
6.1 Inspection with bright-light (white light) .............3
6.2 Inspection with UV-light (black light) .................3
7 Application of this LS .........................................3
8 Equipment used (for information only) ..............3
9 Summary - UV-Bright-Light Inspection
Results ..............................................................4
10 Photo documentation ........................................5

Remarks on the current issue:

Revision: First issue
Previous issues: -
Responsible functional unit(s) for the technical content: GCQ, ENM, RDC

Hock, ENQ
X 01 08.2015 Henn, GCQ Meilinger, RDC Helmreich, GCQ
Pelz, DQ
Status Issue Date Prepared Reviewed Approved

The reproduction, distribution and utilization of this document as well as the communication of its contents to others without express
authorization are prohibited. Offenders will be held liable for the payment of damages.
All rights reserved in the event of the grant of a patent, utility model or design.

LS 141-76 (EN)
 Linde AG, Engineering Division Issue 01/08.2015 LS 141-76 Page 2 of 73

1 Scope
This Linde Standard (LS) serves as a guide for visual cleanliness inspections at Construction Sites and defines
inspection/verification acceptance criteria for piping construction component surfaces in O2-service.
The LS may be used by inspection personnel for comparing inspected surface conditions, indications and
appearances in correlation with the provided reference samples in this LS.

2 Normative references
This LS contains undated references to incorporate provisions of other publications. The normative references are
cited at the respective place in the text and the publications are listed below. Issues valid at the effective date of
contract shall apply.
LS 141-74 Part 13 Cleanliness of surfaces in air separation plants and components - Process piping and tanks
at construction sites

3 Abbreviations and definitions

COMPANY Linde AG, Engineering division, resp. party responsible for Construction Management
Construction Site Site for prefabrication or field assembly as well existing plants where construction work is
carried out
AL Aluminium
CS Carbon Steel
SS Stainless Steel
BL Bright Light (White Light)
UV Ultra Violet (Black Light)

4 General
Complementary to LS 141-74 Part 13 this LS presents photos of a variety of contaminated inner pipe surfaces
which were taken under bright white light and UV light conditions.
The type and concentration of contamination has been applied on 3 different material types each:
 Aluminium pipe 10” (surface as delivered),
 Stainless Steel Pipe 10” (surface as delivered),
 Carbon Steel Pipe 10” (internally grid blasted).
The contaminated surfaces were inspected and evaluated by expert inspection personnel. The actual reference
photos are displayed with reference number in Para.10. Para. 9 summarize the inspection results indicating the
acceptance status and the reference number.

5 Cleanliness requirements
The inner surface of process piping components and tanks shall meet following cleanliness requirements and
related acceptance criteria for visual inspection:
 Organic material such as oil, grease, paint, etc. not ascertainable,
 Cleaning agents including detergents not ascertainable,
 Rust and loose scale, weld spatters, particles dust, fibres or other foreign material > 1 mm not
ascertainable. No accumulation of any particles.
 Moisture, liquids not ascertainable.
Adequate methods for cleaning, inspection and preservation of O2-components at Construction Sites are defined
in LS 141-74 Part 13.

LS 141-76 (EN)
 Linde AG, Engineering Division Issue 01/08.2015 LS 141-76 Page 3 of 73

6 Visual Cleanliness Inspection Methods

6.1 Inspection with bright-light (white light)
This method will detect without magnification small particulate material such as dust, oil, grease, moisture etc. It
may be used in conjunction with other methods. A sufficiently bright level of artificial or natural light is essential for
interpretation of surfaces. In general a light intensity of 500 LUX [Lx] will be sufficient for a bright-light inspection.
6.2 Inspection with UV-light (black light)
Many common but not all hydrocarbons or organic oils fluoresce under UV-light (e.g. fluorocarbon oils) and can be
detected by this method, also some vegetable and chemical oils do not fluoresce. As can be seen on the sample
photos the intensity of the fluorescent reflection from various oils differs.
Therefore it is important not to rely solely on the result of the UV-test in evaluating the cleanliness of components
cleaned for oxygen service.
The UV light method might indicate fluorescent areas to be further inspected by other tests such as wipe test. An
UV-light with a wave length between 320 and 370 nm and an UV intensity of 800mW/cm2 shall be used in
darkness or subdue light (near darkness) at a distance of about 10 to 20 cm from the surface being examined.
Note:
The inspection distance may also depend on the recommendation of the Black Light Manufacturer. In case of
doubts, an external test sample shall be prepared as reference.
UV-Light reflections may occur on inspected surface depending on radiation angle of lamp (see Figure 1). Those
reflections shall not be interpreted as fluorescing indication.

Light Reflection

Figure 1: UV-Light reflections

7 Application of this LS
The attached photos which serve as a guide to the inspector may differ in colour intensity, brightness and contrast
depending on the type of printer used. In case of doubts the electronical version provides the most accurate photo
quality.
Note:
The acceptance criteria listed in Para.5 and stipulated in LS 141-74 Part 13 apply obligatory and overruling
independent from visual appearance of contamination shown in attached photo documentation in Para.10
(fluorescent or non-fluorescent).
Any lubricants used at Construction Sites where O2-components are manufactured and/or installed shall be
approved by COMPANY in writing prior to application. This applies for fluorescing and non-fluorescing lubricants.

8 Equipment used (for information only)

Bright Light Inspection: Manufacturer VARTA, Type Daylight

LED 7x5mm
Intensity 58 lumens
Range 63 m

LS 141-76 (EN)
 Linde AG, Engineering Division Issue 01/08.2015 LS 141-76 Page 4 of 73

UV-Light Inspection: Manufacturer UVECO

UV Lamp Xenon 35W High Intensity (ozonfree)
Start-up Time Maximum UV-Intensity in between 15 sec
Quick Re-start After min. cooling time of 5 sec
Filterglass Black– spectral Transmission 315 – 405nm, 140mm
diameter
Reflectormaterial aluminium
Reflectorsize 135mm diameter

Photo Equipment: Manufacturer CANON

Type EOS 600D
Lens EFS 17-55 mm
Focal Distance 500mm
Aperture 8

9 Summary - UV-Bright-Light Inspection Results

1)
Grouping Contamination Ref-No. Result Remark

BL-B-1
Cloth Fibres accept fluorescent
UV-B-1
BL-B-2
AL Chips reject non-fluorescent
UV-B-2
BL-B-3
Solids etc. [B] Perlite reject non-fluorescent
UV-B-3
Lime BL-B-4
accept fluorescent
accumulation UV-B-4
Adsorbent BL-B-5
reject non-fluorescent
MS13X UV-B-5
BL-C-1
Rain accept non-fluorescent
UV-C-1
BL-C-2
Dried waterdrops [C] Tap accept non-fluorescent
UV-C-2
BL-C-3
Salt (NaCl) reject non-fluorescent
UV-C-3
BL-D-1
Butter reject non-fluorescent
UV-D-1
Food [D]
Smudged Salami BL-D-2
reject non-fluorescent
Slice UV-D-2
BL-E-1
Detergent/Soap reject fluorescent
UV-E-1
BL-E-2
Sun Lotion reject reject non-fluorescent
UV-E-2
Silicon oil BL-E-3
reject reject non-fluorescent
(OKS 1360) UV-E-3
Detergent, Used compressor BL-E-4
reject reject fluorescent
Grease and Oil [E] oil (LOX 50) UV-E-4
Sliding agent BL-E-5
reject reject fluorescent
(Oxigenoex S4) UV-E-5
Sliding agent BL-E-6
reject reject fluorescent
(Gleitmo 599) UV-E-6
Sliding agent BL-E-7
reject reject fluorescent
(Glisseal) UV-E-7
Film thickness thick thin
1) Result applies for Al, CS, SS materials

LS 141-76 (EN)
 Linde AG, Engineering Division Issue 01/08.2015 LS 141-76 Page 5 of 73

10 Photo documentation

AL-BL-B-1 (Cloth Fibres)

AL-UV-B-1 (Cloth Fibres)

Acceptable: Yes ■ / No □

LS 141-76 (EN)
 Linde AG, Engineering Division Issue 01/08.2015 LS 141-76 Page 6 of 73

AL-BL-B-2 (AL Chips)

AL-BL-B-2 (AL Chips)

Acceptable: Yes □ / No ■

LS 141-76 (EN)
 Linde AG, Engineering Division Issue 01/08.2015 LS 141-76 Page 7 of 73

AL-BL-B-3 (Perlite)

AL-UV-B-3 (Perlite)
Acceptable: Yes □ / No ■

LS 141-76 (EN)
 Linde AG, Engineering Division Issue 01/08.2015 LS 141-76 Page 8 of 73

AL-BL-B-4 (Lime accumulation)

AL-UV-B-4 (Lime accumulation)

Acceptable: Yes ■ / No □

LS 141-76 (EN)
 Linde AG, Engineering Division Issue 01/08.2015 LS 141-76 Page 9 of 73

AL-BL-B-5 (Adsorbent MS13X)

AL-UV-B-5 (Adsorbent MS13X)

Acceptable: Yes □ / No ■

LS 141-76 (EN)
 Linde AG, Engineering Division Issue 01/08.2015 LS 141-76 Page 10 of 73

AL-BL-C-1 (Dried waterdrops - Rain)

AL-UV-C-1 (Dried waterdrops - Rain)

Acceptable: Yes ■ / No □

LS 141-76 (EN)
 Linde AG, Engineering Division Issue 01/08.2015 LS 141-76 Page 11 of 73

AL-BL-C-2 (Dried waterdrops - Tap)

AL-UV-C-2 (Dried waterdrops - Tap)

Acceptable: Yes ■ / No □

LS 141-76 (EN)
 Linde AG, Engineering Division Issue 01/08.2015 LS 141-76 Page 12 of 73

AL-BL-C-3 (Dried waterdrops - SALt)

AL-UV-C-3 (Dried waterdrops - Salt (NaCl))

Acceptable: Yes □ / No ■

LS 141-76 (EN)
 Linde AG, Engineering Division Issue 01/08.2015 LS 141-76 Page 13 of 73

AL-BL-D-1 (Butter)

AL-UV-D-1 (Butter)
Acceptable: Yes □ / No ■

LS 141-76 (EN)
 Linde AG, Engineering Division Issue 01/08.2015 LS 141-76 Page 14 of 73

AL-BL-D-2 (Smudged Salami Slice)

AL-UV-D-2 (Smudged Salami Slice)

Acceptable: Yes □ / No ■

LS 141-76 (EN)
 Linde AG, Engineering Division Issue 01/08.2015 LS 141-76 Page 15 of 73

AL-BL-E-1 (Detergent/Soap)

AL-UV-E-1 (Detergent/Soap)
Acceptable: Yes □ / No ■

LS 141-76 (EN)
 Linde AG, Engineering Division Issue 01/08.2015 LS 141-76 Page 16 of 73

AL-BL-E-2.1 (Sun Lotion-Thick)

AL-UV-E-2.1 (Sun Lotion-Thick)

Acceptable: Yes □ / No ■

LS 141-76 (EN)
 Linde AG, Engineering Division Issue 01/08.2015 LS 141-76 Page 17 of 73

AL-BL-E-2.2 (Sun Lotion-Thin)

AL-UV-E-2.2 (Sun Lotion-Thin)

Acceptable: Yes □ / No ■

LS 141-76 (EN)
 Linde AG, Engineering Division Issue 01/08.2015 LS 141-76 Page 18 of 73

AL-BL-E-3.1 (Silicon oil OKS 1360-Thick)

AL-UV-E-3.1 (Silicon oil OKS 1360-Thick)

Acceptable: Yes □ / No ■

LS 141-76 (EN)
 Linde AG, Engineering Division Issue 01/08.2015 LS 141-76 Page 19 of 73

AL-BL-E-3.2 (Silicon oil OKS 1360-Thin)

AL-UV-E-3.2 (Silicon oil OKS 1360-Thin)

Acceptable: Yes □ / No ■

LS 141-76 (EN)
 Linde AG, Engineering Division Issue 01/08.2015 LS 141-76 Page 20 of 73

AL-BL-E-4.1 (Used compressor oil LOX 50-Thick)

AL-UV-E-4.1 (Used compressor oil LOX 50-Thick)

Acceptable: Yes □ / No ■

LS 141-76 (EN)
 Linde AG, Engineering Division Issue 01/08.2015 LS 141-76 Page 21 of 73

AL-BL-E-4.2 (Used compressor oil LOX 50-Thin)

AL-UV-E-4.2 (Used compressor oil LOX 50-Thin)

Acceptable: Yes □ / No ■

LS 141-76 (EN)
 Linde AG, Engineering Division Issue 01/08.2015 LS 141-76 Page 22 of 73

AL-BL-E-5.1 (Sliding agent Oxigenoex S4-Thick)

AL-UV-E-5.1 (Sliding agent Oxigenoex S4-Thick)

Acceptable: Yes □ / No ■

LS 141-76 (EN)
 Linde AG, Engineering Division Issue 01/08.2015 LS 141-76 Page 23 of 73

AL-BL-E-5.2 (Sliding agent Oxigenoex S4-Thin)

AL-UV-E-5.2 (Sliding agent Oxigenoex S4-Thin)

Acceptable: Yes □ / No ■

LS 141-76 (EN)
 Linde AG, Engineering Division Issue 01/08.2015 LS 141-76 Page 24 of 73

AL-BL-E-6.1 (Sliding agent Gleitmo 599-Thick)

AL-UV-E-6.1 (Sliding agent Gleitmo 599-Thick)

Acceptable: Yes □ / No ■

LS 141-76 (EN)
 Linde AG, Engineering Division Issue 01/08.2015 LS 141-76 Page 25 of 73

AL-BL-E-6.2 (Sliding agent Gleitmo 599-Thin)

AL-UV-E-6.2 (Sliding agent Gleitmo 599-Thin)

Acceptable: Yes □ / No ■

LS 141-76 (EN)
 Linde AG, Engineering Division Issue 01/08.2015 LS 141-76 Page 26 of 73

AL-BL-E-7.1 (Sliding agent Glisseal-Thick)

AL-UV-E-7.1 (Sliding agent Glisseal-Thick)

Acceptable: Yes □ / No ■

LS 141-76 (EN)
 Linde AG, Engineering Division Issue 01/08.2015 LS 141-76 Page 27 of 73

AL-BL-E-7.2 (Sliding agent Glisseal-Thin)

AL-UV-E-7.2 (Sliding agent Glisseal-Thin)

Acceptable: Yes □ / No ■

LS 141-76 (EN)
 Linde AG, Engineering Division Issue 01/08.2015 LS 141-76 Page 28 of 73

CS-BL-B-1 (Cloth Fibres)

CS-UV-B-1 (Cloth Fibres)

Acceptable: Yes ■ / No □

LS 141-76 (EN)
 Linde AG, Engineering Division Issue 01/08.2015 LS 141-76 Page 29 of 73

CS-BL-B-2 (AL Chips)

CS-UV-B-2 (AL Chips)

Acceptable: Yes □ / No ■

LS 141-76 (EN)
 Linde AG, Engineering Division Issue 01/08.2015 LS 141-76 Page 30 of 73

CS-BL-B-3 (Perlite)

CS-UV-B-3 (Perlite)
Acceptable: Yes □ / No ■

LS 141-76 (EN)
 Linde AG, Engineering Division Issue 01/08.2015 LS 141-76 Page 31 of 73

CS-BL-B-4 (Lime accumulation)

CS-UV-B-4 (Lime accumulation)

Acceptable: Yes ■ / No □

LS 141-76 (EN)
 Linde AG, Engineering Division Issue 01/08.2015 LS 141-76 Page 32 of 73

CS-BL-B-5 (Adsorbent MS13X)

CS-UV-B-5 (Adsorbent MS13X)

Acceptable: Yes □ / No ■

LS 141-76 (EN)
 Linde AG, Engineering Division Issue 01/08.2015 LS 141-76 Page 33 of 73

CS-BL-C-1 (Dried waterdrops - Rain)

CS-UV-C-1 (Dried waterdrops - Rain)

Acceptable: Yes ■ / No □

LS 141-76 (EN)
 Linde AG, Engineering Division Issue 01/08.2015 LS 141-76 Page 34 of 73

CS-BL-C-2 (Dried waterdrops - Tap)

CS-UV-C-2 (Dried waterdrops - Tap)

Acceptable: Yes ■ / No □

LS 141-76 (EN)
 Linde AG, Engineering Division Issue 01/08.2015 LS 141-76 Page 35 of 73

CS-BL-C-3 (Dried waterdrops - Salt (NaCl))

CS-UV-C-3 (Dried waterdrops - Salt (NaCl))

Acceptable: Yes □ / No ■

LS 141-76 (EN)
 Linde AG, Engineering Division Issue 01/08.2015 LS 141-76 Page 36 of 73

CS-BL-D-1 (Butter)

CS-UV-D-1 (Butter)
Acceptable: Yes □ / No ■

LS 141-76 (EN)
 Linde AG, Engineering Division Issue 01/08.2015 LS 141-76 Page 37 of 73

CS-BL-D-2 (Smudged Salami Slice)

CS-UV-D-2 (Smudged Salami Slice)

Acceptable: Yes □ / No ■

LS 141-76 (EN)
 Linde AG, Engineering Division Issue 01/08.2015 LS 141-76 Page 38 of 73

CS-BL-E-1 (Detergent/Soap)

CS-UV-E-1 (Detergent/Soap)
Acceptable: Yes □ / No ■

LS 141-76 (EN)
 Linde AG, Engineering Division Issue 01/08.2015 LS 141-76 Page 39 of 73

CS-BL-E-2.1 (Sun Lotion-Thick)

CS-UV-E-2.1 (Sun Lotion-Thick)

Acceptable: Yes □ / No ■

LS 141-76 (EN)
 Linde AG, Engineering Division Issue 01/08.2015 LS 141-76 Page 40 of 73

CS-BL-E-2.2 (Sun Lotion-Thin)

CS-UVE-2.2 (Sun Lotion-Thin)

Acceptable: Yes □ / No ■

LS 141-76 (EN)
 Linde AG, Engineering Division Issue 01/08.2015 LS 141-76 Page 41 of 73

CS-BL-E-3.1 Silicon Oil (OKS1360)-Thick

CS-UV-E.3.1 Silicon Oil (OKS1360)-Thick

Acceptable: Yes □ / No ■

LS 141-76 (EN)
 Linde AG, Engineering Division Issue 01/08.2015 LS 141-76 Page 42 of 73

CS-BL-E-3.2 -Silicon Oil (OKS1360)-Thin

CS-UV-E- 3.2 Silicon Oil (OKS1360)-Thin

Acceptable: Yes □ / No ■

LS 141-76 (EN)
 Linde AG, Engineering Division Issue 01/08.2015 LS 141-76 Page 43 of 73

CS-BL-E-4.1 Used compressor oil (LOX 50 )thick

CS-UV-E-4.1 Used compressor oil (LOX 50) thick

Acceptable: Yes □ / No ■

LS 141-76 (EN)
 Linde AG, Engineering Division Issue 01/08.2015 LS 141-76 Page 44 of 73

CS-BL-E-4.2 Used compressor oil (LOX 50) thin

CS-UV-E-4.2 Used compressor oil (LOX 50) thin

Acceptable: Yes □ / No ■

LS 141-76 (EN)
 Linde AG, Engineering Division Issue 01/08.2015 LS 141-76 Page 45 of 73

CS-BL-E-5.1 Sliding agent (Oxigenoex S4) thick

CS-UV-E-5.1 Sliding agent (Oxigenoex S4) thick

Acceptable: Yes □ / No ■

LS 141-76 (EN)
 Linde AG, Engineering Division Issue 01/08.2015 LS 141-76 Page 46 of 73

CS-BL-E-5.2 Sliding agent (Oxigenoex S4) thin

CS-UV-E-5.2 Sliding agent (Oxigenoex S4) thin

Acceptable: Yes □ / No ■

LS 141-76 (EN)
 Linde AG, Engineering Division Issue 01/08.2015 LS 141-76 Page 47 of 73

CS-BL-E-6.1 Sliding agent (Gleitmo 599) thick

CS-UV-E-6.1 Sliding agent (Gleitmo 599) thick

Acceptable: Yes □ / No ■

LS 141-76 (EN)
 Linde AG, Engineering Division Issue 01/08.2015 LS 141-76 Page 48 of 73

CS-BL-E-6.2 Sliding agent (Gleitmo 599) thin

CS-UV-E-6.2 Sliding agent (Gleitmo 599) thin

Acceptable: Yes □ / No ■

LS 141-76 (EN)
 Linde AG, Engineering Division Issue 01/08.2015 LS 141-76 Page 49 of 73

CS-BL-E-7.1 Sliding agent (Glisseal) thick

CS-UV-E-7.1 Sliding agent (Glisseal) thick

Acceptable: Yes □ / No ■

LS 141-76 (EN)
 Linde AG, Engineering Division Issue 01/08.2015 LS 141-76 Page 50 of 73

CS-BL-E-7.2 Sliding agent (Glisseal) thin

CS-UV-E-7.2 Sliding agent (Glisseal) thin

Acceptable: Yes □ / No ■

LS 141-76 (EN)
 Linde AG, Engineering Division Issue 01/08.2015 LS 141-76 Page 51 of 73

SS-BL-B-1 Cloth Firbres

SS-UV-B-1 Cloth Fibres

Acceptable: Yes ■ / No □

LS 141-76 (EN)
 Linde AG, Engineering Division Issue 01/08.2015 LS 141-76 Page 52 of 73

SS-BL-B-2 AL Chips

SS-UV-B-2 AL Chips
Acceptable: Yes □ / No ■

LS 141-76 (EN)
 Linde AG, Engineering Division Issue 01/08.2015 LS 141-76 Page 53 of 73

SS-BL-B-3 Perlite

SS-UV-B-3 Perlite
Acceptable: Yes □ / No ■

LS 141-76 (EN)
 Linde AG, Engineering Division Issue 01/08.2015 LS 141-76 Page 54 of 73

SS-BL-B-4 Lime

SS-UV-B-4 Lime
Acceptable: Yes ■ / No □

LS 141-76 (EN)
 Linde AG, Engineering Division Issue 01/08.2015 LS 141-76 Page 55 of 73

SS-BL-B-5 Adsorbent MS13X

SS-UV-B-5 Adsorbent MS13X

Acceptable: Yes □ / No ■

LS 141-76 (EN)
 Linde AG, Engineering Division Issue 01/08.2015 LS 141-76 Page 56 of 73

SS-BL-C-1 Rain Water dried

SS-UV-C-1 Rain Water dried

Acceptable: Yes ■ / No □

LS 141-76 (EN)
 Linde AG, Engineering Division Issue 01/08.2015 LS 141-76 Page 57 of 73

SS-BL-C-2 Tap Water dried

SS-UV-C-2 Tap Water dried

Acceptable: Yes ■ / No □

LS 141-76 (EN)
 Linde AG, Engineering Division Issue 01/08.2015 LS 141-76 Page 58 of 73

SS-BL-C-3 Salt (NaCl) Water dried

SS-UV-C-3 Salt (NaCl) Water dried

Acceptable: Yes □ / No ■

LS 141-76 (EN)
 Linde AG, Engineering Division Issue 01/08.2015 LS 141-76 Page 59 of 73

SS-BL-D-1 Butter

SS-UV-D-1 Butter
Acceptable: Yes □ / No ■

LS 141-76 (EN)
 Linde AG, Engineering Division Issue 01/08.2015 LS 141-76 Page 60 of 73

SS-BL-D-2 (Smudged Salami Slice)

SS-UV-D-2 (Smudged Salami Slice)

Acceptable: Yes □ / No ■

LS 141-76 (EN)
 Linde AG, Engineering Division Issue 01/08.2015 LS 141-76 Page 61 of 73

SS-BL-E-1 (Detergent/Soap)

SS-UV-E-1 (Detergent/Soap)
Acceptable: Yes □ / No ■

LS 141-76 (EN)
 Linde AG, Engineering Division Issue 01/08.2015 LS 141-76 Page 62 of 73

SS-BL-E-2.1 Sun Lotion thick

SS-UV-E-2.1 Sun Lotion thick

Acceptable: Yes □ / No ■

LS 141-76 (EN)
 Linde AG, Engineering Division Issue 01/08.2015 LS 141-76 Page 63 of 73

SS-BL-E-2.2 Sun Lotion thin

SS-UV-E-2.2 Sun Lotion thin

Acceptable: Yes □ / No ■

LS 141-76 (EN)
 Linde AG, Engineering Division Issue 01/08.2015 LS 141-76 Page 64 of 73

SS-BL-E-3.1 Silicon Oil OKS 1360 thick

SS-UV-E-3.1 Silicon Oil OKS 1360 thick

Acceptable: Yes □ / No ■

LS 141-76 (EN)
 Linde AG, Engineering Division Issue 01/08.2015 LS 141-76 Page 65 of 73

SS-BL-E-3.2 Silicon Oil OKS 1360 thin

SS-UV-E-3.2 Silicon Oil OKS 1360 thin

Acceptable: Yes □ / No ■

LS 141-76 (EN)
 Linde AG, Engineering Division Issue 01/08.2015 LS 141-76 Page 66 of 73

SS-BL-E-4.1 Used Compressor Oil LOX 50 thick

SS-UV-E-4.1 Used Compressor Oil LOX 50 thick

Acceptable: Yes □ / No ■

LS 141-76 (EN)
 Linde AG, Engineering Division Issue 01/08.2015 LS 141-76 Page 67 of 73

SS-BL-E-4.2 Used Compressor Oil LOX 50 thin

SS-UV-E-4.2 Used Compressor Oil LOX 50 thin

Acceptable: Yes □ / No ■

LS 141-76 (EN)
 Linde AG, Engineering Division Issue 01/08.2015 LS 141-76 Page 68 of 73

SS-BL-E-5.1 Sliding agent (Oxigenoex S4) thick

SS-UV-E-5.1 Sliding agent (Oxigenoex S4) thick

Acceptable: Yes □ / No ■

LS 141-76 (EN)
 Linde AG, Engineering Division Issue 01/08.2015 LS 141-76 Page 69 of 73

SS-BL-E-5.2 Sliding agent (Oxigenoex S4) thin

SS-UV-E-5.2 Sliding agent (Oxigenoex S4) thin

Acceptable: Yes □ / No ■

LS 141-76 (EN)
 Linde AG, Engineering Division Issue 01/08.2015 LS 141-76 Page 70 of 73

SS-BL-E-6.1 Sliding agent (Gleitmo 599) thick

SS-UV-E-6.1 Sliding agent (Gleitmo 599) thick

Acceptable: Yes □ / No ■

LS 141-76 (EN)
 Linde AG, Engineering Division Issue 01/08.2015 LS 141-76 Page 71 of 73

SS-BL-E-6.2 Sliding agent (Gleitmo 599) thin

SS-UV-E-6.2 Sliding agent (Gleitmo 599) thin

Acceptable: Yes □ / No ■

LS 141-76 (EN)
 Linde AG, Engineering Division Issue 01/08.2015 LS 141-76 Page 72 of 73

SS-BL-E-7.1 Sliding agent (Glisseal) thick

SS-UV-E-7.1 Sliding agent (Glisseal) thick

Acceptable: Yes □ / No ■

LS 141-76 (EN)
 Linde AG, Engineering Division Issue 01/08.2015 LS 141-76 Page 73 of 73

SS-BL-E-7.2 Sliding agent (Glisseal) thin

SS-UV-E-7.2 Sliding agent (Glisseal) thin

Acceptable: Yes □ / No ■

LS 141-76 (EN)