Objective 1-100
Objective 1-100
Objective 1-100
Q2- According to maximum moving dimensions for BG track maximum overall height at top
center can be
a) 4470 mm
b) 4115 mm
c) 4213 mm
d) None of the above
Q3- According to maximum moving dimensions for BG track maximum height of OHE from rail
level can be
(a) 4470 mm
(b) 4115 mm
(c) 4444 mm
(d) 4000 mm
Q4- According to maximum moving dimensions for BG track maximum overall height at the side
can be
(a) 3405 mm
(b) 3505 mm
(c) 3000 mm
(d) None of these
Q5- According to maximum moving dimensions for BG track maximum overall width of eight
wheeler
(a) 3250 mm
(b) 4000 mm
(c) 3350 mm
(d) None of the above
Q6- According to maximum moving dimensions for BG track maximum height of floor from rail
level is
(a) 102 mm
(b) 200 mm
(c) 109 mm
(d) None of the above
1 of 34 | P a g e
Q7- According to maximum moving dimensions for BG track the maximum overall width at
bottom will be
(a) 1600 mm
(b) 1605 mm
(c) 1610 mm
(d) None of the above
Q9- Which of the following is not a type of clearance for ODC point of view
(a) Net clearance
(b) Gross clearance
(c) Cumulative clearance
(d) All of the above
2 of 34 | P a g e
Q14-Which of the following is correct
(a) Net clearance is greater than gross clearance
(b) Gross clearance is greater than net clearance
(c) Both are same
(d) None of the above
3 of 34 | P a g e
Q22- If there is AC traction and gaph between wire and ODC is more than 390 mm the maximum
speed allowed is
a) 40 kmph
b) 60 kmph
c) 70 kmph
d) 100 kmph
Q23- If there is DC traction and gaph between wire and ODC is between 170 mm and 75 mm
the maximum speed allowed is
a) 15 kmph
b) 60 kmph
c) 70 kmph
d) 100 kmph
4 of 34 | P a g e
Q29- Which of the following is component of WILD
a) Instrumented tracks
b) Signal conditioning unit
c) Train trigger sensor
d) All of the above
Q33- If the signal is audio visual critical alarm then what does it indicates
a) Train is ok
b) Train needs attention
c) Affected coach /wagon should be examined at next TXR point
d) None of the above
5 of 34 | P a g e
Q37- Which of the following system is a combination of weighbridge and WILD
a) HBD
b) TBMS
c) WCM
d) None of the above
Q38-In WILD system in instrumented track the sleeper spacing from sleeper to sleeper should be
a) 60 cm
b) 50 cm
c) 90 cm
d) 110 cm
Q41- Wayside Hot box detection in a rolling stock can be done using
a) HBD system
b) WILD system
c) WCM
d) None of the above
Q42- Which of the following is not a feature of hot box detector system
(a) It automatic identifies the train
(b) It uses pyrometers to measure temperature of axle box
(c) It uses audio visual alarm for given alarm condition
(d) All of the above
Q43- Time elapsed from the date of realization of need of recoupment to the physical receipt of
material is termed as
a) Buffer time
b) Interim period
c) Contract period
d) Lead time
6 of 34 | P a g e
Q44- EOQ is the Quantity at which –
a) Inventory carrying cost is maximum
b) Warehousing cost is minimum
c) Inventory carrying cost + ordering cost is maximum
d) Inventory carrying cost + ordering cost is minimum
Q49- Height of compartment floor from rail level under tare condition of LHB coaches?
a) 1320mm
b) 1389mm
c) 1305mm
d) 1345mm
Q51- What is Maximum height of centre line of side CBC above rail for empty vehicle?
a) 1108mm
b) 1107mm
c) 1105mm
d) 1103mm
7 of 34 | P a g e
Q52- What is minimum height of centre line of CBC above rail level for loaded vehicle?
a) 1030mm
b) 1039mm
c) 1025mm
d) 1015mm
8 of 34 | P a g e
Q61- What is the diameter of brake disc?
a) 650 mm
b) 630 mm
c) 640 mm
d) 645 mm
Q65- How many types of shock absorbers are used in LHB Coaches?
a) 6
b) 5
c) 4
d) 3
Q67- What is the name of shock absorber connected between bogie and car body?
a) Primary
b) Secondary
c) Yaw
d) None of these
9 of 34 | P a g e
Q70- What is the height over roof of LHB Coaches?
a) 4200 mm
b) 4390 mm
c) 4039 mm
d) 4190 mm
Q74- Maximum permissible buffer drop under gross load and worn condition is -
a) 65 mm
b) 70 mm
c) 75 mm
d) 80 mm
10 of 34 | P a g e
Q79- ‘SS-II’ of LHB coach is done –
a) 1 year
b) 2 years
c) 1.5 year/ 6 lakhs Kms earned whichever is earlier
d) 3 years/ 12 lakhs Kms earned whichever is earlier
Q85- Brake power of air brake for Rajdhani coaches from out station is -
a) 90%
b) 100%
c) 85%
d) 95%
Q87- To protect vertical sliding between engine and power car, the device is known as -
a) Vertical slide protector
b) Restrictor
c) Protecting device.
d) None of these
11 of 34 | P a g e
Q88- What is the wheel base of LHB bogie?
a) 2440 mm
b) 2696 mm
c) 2560 mm
d) 2570 mm
Q93- Cross members of under frame of LHB Coaches are manufactured from -
a) Austenitic steel (SS 304)
b) IRSM-41
c) Ferritic steel (SS-409)
d) IRSM-44
12 of 34 | P a g e
Q97- Sole bar of LHB Coaches are manufactured from -
a) Austenitic steel (SS 304)
b) IRSM-41
c) Ferritic steel (SS-409)
d) IRSM-44
13 of 34 | P a g e
Q105- Barrel length of BTPN tank wagon is –
(a) 11460 mm
(b) 11550 mm
(c) 11458 mm
(d) 12100 mm
Q108- During Hydraulic testing of master valve of tank wagon, the water to be filled up to be –
(a) 130 Cm
(b) 150 Cm
(c) 180 Cm
(d) 200 Cm
Q111- What is the inside barrel diameter of the TPGLR tank wagon?
(a) 2100 mm
(b) 2230 mm
(c) 2300 mm
(d) 2330 mm
14 of 34 | P a g e
Q113- Tare weight of the TPGLR tank wagon is -
(a) 17.82 t
(b) 17.32
(c) 18.2 t
(d) 17.1 t
Q114- The mechanical code of bogie Patrol tank wagon fitted with pneumatic brake is -
(a) BTPAN
(b) LBM
(c) LBM
(d) LCT
Q115- The mechanical code of bogie Liquefied anhydrous ammonia gas tank wagon is -
(a) BTAL &BTALN
(b) TBS & BTSA
(c) AST & TSMBA
(d) TBT& MBTOX
15 of 34 | P a g e
Q121- No. of safety valve fitted in liquefied petroleum gas tank is -
(a) One
(b) Two
(c) Three
(d) None of the above
Q123- No of safety vent with frangible disc fitted in sulphuric acid tank wagon is -
(a) One
(b) Two
(c) Three
(d) None of the above
Q124- How many no of safety vent with frangible disc fitted in liquid chlorine tank wagon is -
(a) One
(b) Two
(c) Three
(d) None of the above
Q125- What is the hydraulic test pressures in a barrel of LPG tanks wagon?
(a) 26.36 kg/ Cm2
(b) 23.7 kg/ Cm2
(c) 28.33 kg/ Cm2
(d) 33.23 kg/ Cm2
Q127- In the tank wagon, close the vapour extractor cock after -
(a) Un loading
(b) Loading
(c) Running
(d) None of the above
16 of 34 | P a g e
Q129- The diameter of master valve of BTPN tank wagon is –
(a) 90 mm
(b) 100 mm
(c) 110 mm
(d) 200 mm
Q131- Thickness of barrel plate (Cylindrical portion) of BTPGL tank barrel is-
(a) 10 mm
(b) 12 mm
(c) 15 mm
(d) 18 mm
17 of 34 | P a g e
Q137- Length of over Headstock to Headstock for A-car of BLC wagon is–
(a) 13650 mm
(b) 13625 mm
(c) 13555mm
(d) 13365mm
Q138- In BLC wagon, height of slackness drowbar system from Rail level is–
(a) 890 mm
(b) 848 mm
(c) 845mm
(d) 910mm
Q139- At the time of load distribution what is the percentage of load that comes on centre pivot?
(a) 10%
(b) 15%
(c) 20%
(d) 25%
Q140- Length of over Slack less draw bar for B-car of BLC wagon is–
(a) 14566 mm
(b) 13156 mm
(c) 12212mm
(d) 14763mm
Q142- The standard height of platform for BLC wagon from Rail level is–
(a) 1010 mm
(b) 1015 mm
(c) 1009mm
(d) 1100mm
18 of 34 | P a g e
Q146- Condemning limit of BLC wheel set is–
(a) 900 mm
(b) 800 mm
(c) 670mm
(d) 780mm
Q147- Maximum height of side frame from Rail level of container bogie type LCCF 20 (C) trolley
is–
(a) 851 mm
(b) 715 mm
(c) 932mm
(d) 786mm
Q148- In BLC wagon, width over sole bar at centre line wagon is–
(a) 2200 mm
(b) 2100 mm
(c) 2150mm
(d) 2180mm
Q149- For lifting the container, force required to lift the container on automatic twist lock is-
(a) 1050 Kg
(b) 1000 Kg
(c) 1100 Kg
(d) 11590Kg
Q152- In place of empty load box what device is used in BLC wagon?
a) BSD
b) LSD
c) SDF
d) SAB
Q153- As per RDSO standard what shall be the Max. Allowed speed of BFKI?
(a) 75Km/h
(b) 80Km/h
(c) 100 Km/h
(d)110Km/h
19 of 34 | P a g e
Q155- Who is PHOD of store department at zonal level?
a) Chief Material Manager
b) Chief Store Manager
c) Controller of Stores
d) None of these
Q157- The items which are not required frequently but are still necessary to maintain a stock
ready for use, this type of stores are termed as;
a) Special stores
b) Miscellaneous stores
c) Ordinary stores
d) Emergency stores
Q158- In how many MAJOR groups are the railway stores CODIFIED?
a) 10
b) 20
c) 50
d) 75
Q159- In how many SUB groups are the railway stores CODIFIED?
a) 10
b) 75
c) 99
d) None of these
Q160- Under which of the following groups C & W parts are listed?
a) 00-08
b) 10-19
c) 21-28
d) 30-39
20 of 34 | P a g e
Q163- Which of the following is not the source of material in railways?
a) Indigenous purchase
b) Imports
c) Loan of stores from other railways
d) None of the above
DISASTER MANAGEMENT
Q165- Which of the following parameter is not considered under Technical knowledge of a loco
pilot?
a) Knowledge regarding C & W fittings
b) Knowledge regarding traction fittings
c) Knowledge regarding track fittings
d) Troubleshooting capabilities of DSL/Elect traction
Q166- As per accident manual accidents are classified in 16 categories from A to R excluding
a) B & D
b) I & O
c) P & Q
d) C & O
Q167- As per the accident manual, which of the following is not class of railway property;
a) Rolling stock
b) Locomotives
c) Luggage
d) Permanent way
Q168- Which of the following does not cover under definition of cattle as per accident manual?
a) Cow
b) Elephant
c) Buffalo
d) Donkey
21 of 34 | P a g e
Q169- Which of the following is the duty of engine crew during accident?
a) Note down the time of accident
b) Arranging protection of front portion of the train in accordance with rule in force
c) Provide assistance to guard in assessment of damage to rolling stock
d) All of the above
Q171- The horizontal distance from centre line of the lifting hook to the head stock(under
carriage), is called
a) Hoisting
b) Slewing
c) Derricking
d) Outreach
22 of 34 | P a g e
Q176- How is B class ART different for A class ART?
a) Diesel crane is not provided in B class ART
b) Bulldozer is not provided in B class ART
c) Diesel crane & Bulldozer is not provided in B class ART
d) Diesel crane is not provided in A class ART
Q177- For how much time the records of class A & B accidents shall be preserved
a) 5 years
b) 3 years
c) 10 years
d) 2 years
Q180- The effective span or area of the supporting base when outriggers are used to increase
stability by virtue of making contact with the ground at points further from the ventre line of the
crane than the normal wheels/track position, is called
a) Tail radius
b) Prop base
c) Outreach
d) Working radius
Q181- Which of the following is useful in embankements where the soil cannot take heavy loads?
a) Small prop base
b) Large prop base
c) Small outreach
d) Small tail radius
Q182- The mobvement of the hook, main or auxilliary, with or without load, when being raised or
lowered vertically, is known as;
a) Hoisting
b) Slewing
c) Derricking
d) Outreach
23 of 34 | P a g e
Q183- The movement of jib rotating around the vertical axis, is called;
a) Hoisting
b) Slewing
c) Derricking
d) Outreach
TRAIN PARTING
Q184- What is the slot of draft key in drawbar hook in ICF coach?
a) 36.0 mm
b) 37.0 mm
c) 38.0 mm
d) 39.0 mm
Q189 - The projection of the shoulder on the draw hook from headstock is within;
a) 80 to 100 mm
b) 90 to 110 mm
c) 92 to 120 mm
d) 100 to 120 mm
24 of 34 | P a g e
Q190- Enhance capacity of buffer specification No: IRS-M 10 are fitted in all BG maintenance
coach is-
a) 910 kg.m
b) 1030 kg.m
c) 1210kg.m
d) 1290 kg.m
Q194- Maximum nominal thickness of plunger faceplate in ICF type buffer is-
a) 19.0 mm
b) 22.0 mm
c) 24.0 mm
d) 26.0 mm
Q195- In buffer causing, the vertically distance of holes from center of buffer is-
a) 60.3±0.2 mm
b) 62.3±0.5 mm
c) 59.3±0.2 mm
d) 61±0.4 mm
Q196- In buffer easing, the horizontal distance of holes from center of buffer is-
a) 163.5±0.2 mm
b) 169.3±0.4 mm
c) 174.5±0.2 mm
d) 176.3±0.2 mm
25 of 34 | P a g e
Q198- What is the weakest link of the ‘H’ type tight lock center buffer coupler?
a) Draft gear
b) Knuckle
c) Lock
d) Yoke pin
Q199- The minimum tensile stress of ‘H’ type tight lock center buffer coupler is-
a) 6560 kg/cm2
b) 6112 kg/cm2
c) 6327 kg/cm2
d) 6720 kg/cm2
Q200- The minimum yield stress of ‘H’ type tight lock center buffer coupler is-
a) 3890 kg/cm2
b) 4218 kg/cm2
c) 4310 kg/cm2
d) 4560 kg/cm2
Q201- Minimum elongation in 51.0 mm of ‘H’ type tight lock center buffer coupler is-
a) 10%
b) 15%
c) 18%
d) 22%
26 of 34 | P a g e
Q206- What type of gear is used in Brake Van Goods?
a) Screw coupling
b) CBC
c) HT coupling
d) NT coupling
Q208- At present all new coaches are being manufactured with bogie mounted aire brake system
and-
a) Enhance capacity drew gear
b) Load sensing device
c) Dual brake system
d) None of the above
Q210- Which RDSO’s technical pamphlet is reffered, for maintenance of Alliance-II coupler?
a) G-45
b) G-78
c) G-62
d) G-40
Q211- The minimum permissible buffer height above rail line to center of H/Stock under loaded
condition is-
a) 1105 mm
b) 1145 mm
c) 1115 mm
d) 1030 mm
27 of 34 | P a g e
Q213- Min permissible buffer projection from headstock is-
a) 635 mm
b) 6605 mm
c) 590 mm
d) 584 mm
Q218- Standard dimension of shank wear plate for AAR coupler is-
a) 12 mm
b) 8 mm
c) 6 mm
d) 14 mm
Q219- Standard dimension of distance between the nose of knuckle and guard arm is-
a) 140 mm
b) 150 mm
c) 127 mm
d) 12 mm
Q220- Wear limit of distance between the nose of knuckle and guard arm is-
a) 140 mm
b) 155 mm
c) 125 mm
d) 130 mm
28 of 34 | P a g e
Q221- For goods train, max. Buffer Height from level is-
a) 1105 mm
b) 1115 mm
c) 1015 mm
d) 1100 mm
Q222- The maximum permissible free slack in the draft gear in service is-
a) 35 mm
b) 30 mm
c) 25 mm
d) 20 mm
Q223- For short case, what shall be the max buffer projection from the headstock on BG wagon.
a) 480 mm
b) 456 mm
c) 460 mm
d) 510 mm
Q224- For short case, what shall be the max buffer projection from the headstock on BG wagon?
a) 420 mm
b) 440 mm
c) 410 mm
d) 406 mm
Q225- What is the max. Permissible wears in Draw Bars shackle pinhole?
a) 5.23 mm
b) 6.35 mm
c) 7.21 mm
d) 6.69 mm
Q226- What is the max. Permissible wears in Draw Bars shackle pinhole?
a) 10.7 mm
b) 12.3 mm
c) 12.7 mm
d) 13.1 mm
29 of 34 | P a g e
Q229- To adjust buffer height for 930 mm wheel diameter on BCN wagon except CASNUB 22
W, packing piece used is-
a) 38 mm
b) 37 mm
c) 33 mm
d) 32 mm
Q231- What type of head and shank are used in AAR type center buffer coupler?
a) E & G Type
b) E & F Type
c) F & E Type
d) H & F Type
Q232- The yield strength of knuckle of material AAR-M-201 Grade ‘C’ (STD) is-
a) 180t
b) 171t
c) 142t
d) 132t
Q233- The yield strength of knuckle of material AAR-M-201 Grade ‘E’ (HT) is-
a) 180t
b) 171t
c) 142t
d) 132t
Q234- The yield strength of coupler body of AAR Grade ‘C’ (STD) is-
a) 180t
b) 169t
c) 179t
d) 159t
30 of 34 | P a g e
Q237- The tensile stroke of CBC is -
a) 53-58 mm
b) 45-50 mm
c) 60-65 mm
d) 35-40 mm
31 of 34 | P a g e
Q245- During coupling operation the coaches should be -
a) On a curved track
b) On a straight track
c) Either a or b.
d) None of these
32 of 34 | P a g e
Q254- To keep the coupler in level, the maximum distance between centre of coupler and lower
edge of socket should be
a) 250mm
b) 260mm
c) 240mm
d) 255 mm
33 of 34 | P a g e
Q262- Permissible diameter of knuckle pivot pin is -
(a) 41 mm
(b) 38.5 mm
(c) 39.5 mm
(d) 40.5 mm
Q266- Wear limit of distance between the nose of Knuckle and guard arm is –
(a) 140 mm
(b) 155 mm
(c) 125 mm
(d) 130 mm
Q267- For goods train, max. Buffer height from rail level is -
(a) 1105 mm
(b) 1115 mm
(c) 1015 mm
(d) 1100 mm
34 of 34 | P a g e