Combivert f5 Series

COMBIVERT
GB INSTRUCTION MANUAL Control Circuit from V3.2
Mat.No. Rev.
00F5SEB-K320 2E
Downloaded from www.Manualslib.com manuals search engine

This Instruction Manual describes the control circuit of the KEB COMBIVERT F5 - Series. It
GB is only valid together with the Instruction Manuals Part 1 and Part 2. Both Instruction Manuals
must be made available to the user. Prior to performing any work on the unit the user must
familiarize himself with the unit. This includes especially the knowledge and observance of the
safety and warning directions of Part 1. The pictographs used in this instruction manual have
following meaning:
GB - 3.......GB - 38 Danger Attention Information
Warning observe at Help
Caution all costs Tip

Table of Contents
1. Intended use.................................................... 4
2. Installation and Connection........................... 5

2.1 Summary.......................................................................5
2.1.1 Housing Size D - E.........................................................5
2.1.2 Housing Size >= G..........................................................5
2.2 Control board Servo.....................................................6
2.2.1 Assignment of Terminal Strip X2A..................................6
2.2.2 Connection of the control circuit.....................................7
2.2.3 Digital Inputs...................................................................7
2.2.4 Analog Inputs..................................................................7
2.2.5 Voltage Input / External Power Supply...........................8
2.2.6 Digital Outputs................................................................8
2.2.7 Relay Outputs.................................................................8
2.2.8 Analog Outputs...............................................................8
2.2.9 Voltage Output................................................................8
2.2.10 Motor connection............................................................9
2.2.11 Resolver connection X3A..............................................10
2.2.12 incremental encoder simulation X3B............................10
2.2.13 Cable............................................................................11
2.3 Operator.......................................................................12
3. Operation of the Unit..................................... 13

3.1 Keyboard.....................................................................13
3.2 Parameter Summary...................................................14
3.2.1 Password Input.............................................................15
3.2.2 Operating Display.........................................................15
3.2.4 Special Adjustments.....................................................20
3.3 Motor data (factory setting).......................................26
3.4 The drive mode...........................................................27
3.4.1 Start / stop drive.............................................................27
3.4.2 Changing the direction of rotation.................................27
3.4.3 Presetting the setpoint..................................................27
3.4.4 Leaving the drive mode................................................27
4. Error Assistance............................................ 28
5. Initial Start-up................................................ 34
6. Adjustment Speed Controller....................... 35
7. Quick Reference............................................ 36
8. Passwords...................................................... 39
GB - 3
General
1. Intended use
The digital servo controller KEB COMBIVERT F5-SERVO serves exclusively for the control and regulation of the
servo motors KEB COMBIVERT SM.
On delivery the controllers are tuned to the servo motors supplied by KEB. So you receive a highly dynamic drive
which is connected and ready for operation within the shortest time for standard applications.
The operation of other motors requires an adaption of the amplifier and is to be recommended only with special
knowledge of control technology.
KEB COMBIVERT F5-SERVO has very extensive programming options. To make the operation and start-up
simpler for the user, a special operator level was created in which the most important parameters are found.
However, if the parameters pre-defined by KEB are not sufficient for your application an application manual is
available.
GB - 4
Installation and Connection
2. Installation and Connection

2.1 Summary
2.1.1 Housing Size D - E
Optional Operator
with 9-pole Sub-D Socket
Parameter Interface

X2A
Connection

Connection of control terminal

X3B
9-pole Sub-D Socket
Incremental encoder simulation
X3A
15-pole Sub-D Socket
Closed-loop resolver system
2.1.2 Housing Size >= G
Optional Operator
with 9-pole Sub-D Socket

Parameter Interface

X3B
9-pole Sub-D Socket
Incremental encoder simulation

X3A
15-pole Sub-D Socket
Closed-loop resolver system
X2A
Connection
Connection of control terminal

Observe the maximal width of

connectors for X3A and X3B
GB - 5
2.2 Control board Servo X2A

2.2.1 Assignment of 1 2 3 4 5 6 7 8 9 10 11 12 13 14 15 16 17 18 19 20 21 22 23 24 25 26 27 28 29
Terminal Strip X2A
PIN Function Name Description

Analog inputs
1 + Set value input 1 AN1+
0...±10 VDC ^ 0...±CP.22
2 - Set value input 1 AN1- Resolution 12 Bit
3 + Analog input 2 AN2+ Scan time 1 ms
0...±10 VDC ^ 0...±100 %
4 - Analog input 2 AN1-
Analog outputs 5 mA; Ri=100 Ω
Analog output of the real speed Resolution 12 Bit
5 Analog output 1 ANOUT1
0…±10 VDC ^ 0…±3000 rpm PWM frequency 3,4 kHz
Analog output of the apparent current Limiting frequency
6 Analog output 2 ANOUT2
0…10 VDC ^ 0…2 x IN Filter 1. Harmonic 178 Hz
Voltage supply
7 +10 V Output CRF Reference voltage for setpoint potentiometer +10 VDC +5% / max. 4 mA
8
Analog Mass COM Mass for analog in- and outputs
9
Digital inputs
10 Fixed Speed 1 I1 I1+I2 = fixed speed 3 (default: 0 rpm)
11 Fixed speed 2 I2 no input = analog set value
1)
12 External fault I3 Input for external fault stopping mode
13 - I4 No function deposited in the CP-Mode 13…30 V DC ±0 % stabilized
14 Limit switch forward F 1) Ri=2,1 kΩ
Software limit switch
15 Limit switch reverse R Scan time 1 ms
Power modules are enabled;
16 Control release / Reset ST
Error Reset at opening
17 reset RST Reset; only when an error occurs
Transistor outputs
18 Speed dependent O1 Transistor output switched at actual speed = set speed
19 Ready signal O2 Transistor output switched, as long as no error occurs
Voltage supply
20 24 V-Output Uout Approx. 24V output (max.100 mA))
21 20...30 V-Input Uin Voltage input for external supply
22
Digital Mass 0V Potential for digital in-/outputs
23
Relay Outputs
24 NO contact 1 RLA
Fault relay (default);
25 NC contact 1 RLB
Function can be changed with CP.33 at maximum
26 Switching contact 1 RLC
30 V DC
27 NO contact 2 FLA
Run-Signal (default); 0.01…1 A
28 NC contact 2 FLB
Function can be changed with CP.34
29 Switching contact 2 FLC
1) The reaction can be adjusted with CP.35 and CP. 36.. If the unit is defective there is no
guarantee that the software protective function will work.
GB - 6
2.2.2 Connection of the control circuit

In order to prevent a malfunction caused by interference voltage supply on the control inputs, the following
directions should be observed:
• Use shielded / drilled cables
• Lay shield on one side of the inverter onto earth potential
• Lay control and power cable separately (about 10...20 cm apart); Lay crossings in a right angle (in
EMC case it cannot be prevented)
2.2.3 Digital Inputs

Using of the internal voltage supply
X2A 10 11 12 13 14 15 16 17 20 21 22 23 PE
Using of an external voltage supply
X2A 10 11 12 13 14 15 16 17 23 PE
13…30 V DC ±0 %
stabilized
Ri = 2,1 kΩ +
20…30 V DC
2.2.4 Analog Inputs

Connect unused analog inputs to common, to prevent set value fluctuations !
Analog set value setting in speed regulated operation (CP.10 = 4):
external internal
Ri = 55 k
X2A 1 2 3 4 5 6 7 8 9 PE X2A 1 2 3 4 5 6 7 8 9 PE
*)
+
0...±10 VDC
R = 3...10 k
Analog set value setting in torque regulated operation (CP.10 = 5) and reference source CP.28 = 1: 
Ri = 55 k
X2A 1 2 3 4 5 6 7 8 9 PE
*)
+
0...±10 VDC
*) Connect potential equalizing line only if a potential difference of >30 V exists between the controls.
The internal resistance is reduced to 30 kΩ.
GB - 7
2.2.5 Voltage Input / External Power Supply

The supply of the control circuit through an external voltage source keeps the control in operational condition even
if the power stage is switched off. To prevent undefined conditions at external power supply the basic procedure
is to first switch on the power supply and after that the inverter.
X2A 10 11 17 18 19 20 21 22 23 PE
+
20…30 V ±0 % / 1 A DC
stabilized
2.2.6 Digital Outputs
X2A 10 18 19 20 21 22 23 PE
max. 50 mA DC
for both outputs
2.2.7 Relay Outputs

In case of inductive load on the relay outputs a protective wiring must be provided (e.g. free-wheeling diode)!
X2A 24 25 26 27 28 29 PE
max. 30 VDC / 1 A
2.2.8 Analog Outputs

2.2.9 Voltage Output
The voltage output serves for the setting of the digital inputs as well as for the supply of external control elements.
Do no exceed the maximum output current of 100 mA.
X2A 10 18 19 20 21 22 23 PE
+ -
ca. 24 VDC / max. 100 mA
GB - 8
2.2.10 Motor connection

The power connector may only be connected / disconnected when the device and the power
supply are disconnected !
Observe correct phase sequence of the servo motor !
2 PE PE
1 U U
B C
4 V V
3 W W
A D
4 PA
1 3 PB
2 C PTC-connection T1
D PTC-connection T2
Servo motor A Brake + external brake supply

Power connector
B Brake – unit with own voltage
supply
Motor housing / Connect shielding at both

screw connection sides
with large surface !
Connector Cable
Name
Pin No. Core No.
1 U 1
4 V 2
3 W 3
2 PE green-yellow
A Brake + 5
B Brake – 6
C PTC-Contact 7
D PTC-Contact 8
GB - 9
2.2.11 Resolver connection X3A

Motor SERVO
7 6 Resolver X3A
8 12 5 4 3 2 1
5
9 11 10 9 8 7 6
15 14 13 12 11
1 10 4
2 3
housing housing
Signal PIN PIN Core color
– – 14 -
SIN - 1 3 red
SIN+ 10 8 blue
REF- 5 5 yellow
REF+ 7 10 green
COS- 2 4 pink
COS+ 11 9 gray
2.2.12 incremental encoder simulation X3B

The increments of the emulation are fixed to 1024 for units with resolver interface. The 20...30 V voltage supply
at X3A and X3B is loadable with altogether 170 mA. If higher voltages / currents are needed for the supply of the
incremental encoder, then the control must be supplied with an external voltage.
The +5 V voltage is a stabilized voltage, which at X3A and X3B is loadable with altogether 500 mA. Since the +5,2
V are generated from Uvar, the current from Uvar decreases in accordance with following formula:
5,2 V • I+5 V
Ivar = 170 mA - –––––––––
Uvar
X3B PIN No. Signal

1 A+
2 B+
3 N+
4 +5,2 V
5 4 3 2 1 1)
5 Uvar 20…30 V
6 A-
9 8 7 6
7 B-
8 N-
9 GND
1)
depending on power circuit
The tracks A+/A-, B+/B- and N+/N- must be fitted with a terminating resistor of approx. 150 Ω !
The plug may only be connected / disconnected when the inverter and supply voltage are
disconnected!
GB - 10
2.2.13 Cable
For the servo system KEB COMBIVERT F5-SERVO factory-assembled motor and resolver cables are available
in the lengths 5 m, 10 m, 15 m and 20 m.
00.S4 . 019 - 0005

0005 = 5 m
0010 = 10 m
Cable length
0015 = 15 m
0020 = 20 m
019 = Motor cable 1,5 mm²

Part
119 = Motor cable 2,5 mm²
Type designation
00.F5 . 0C1 - 1005

1005 = 5 m
1010 = 10 m
Cable length
1015 = 15 m
1020 = 20 m
Part 0C1 = Resolver cable
Type designation
Max. Encoder cable lenght 50 m. Longer encoder cables on request.
GB - 11
2.3 Operator
As an accessory to the local or external (option: cable 00.F5.0C0-1xxx) operation an operator is necessary. To
prevent malfunctions, the inverter must be brought into nOP status before connecting / disconnecting the operator
(open control release terminal). When starting the inverter, it is started with the last stored values or factory
setting.
Digital operator (part number 00.F5.060‑1000)

Interface operator (part number 00.F5.060‑2000)
x x 5-digit LED Display
x x Operating-/Error display
Normal "LED on"
Error "LED blinks"
- x Interface control
Transmit "LED on"
START
ENTER FUNC.
F/R SPEED
x x Double function keyboard

STOP
- x X6B HSP5 programming and diagnostic

interface
- x X6C RS232/RS485 X6B
COMBIVERT
X6C X6D
Only use the operator interface for the serial data transfer to RS232/485. The direct
connection, PC to the inverter is only valid with a cable (part number 00.F5.0C0‑0010),
otherwise, it would lead to the destruction of the PC-interface !
X6C PIN RS485 Signal Meaning

5 4 3 2 1 1 - - reserved
5 4 3 2 1 2 - TxD transmission signal RS232
3 - RxD receive signal RS232
9 8 7 6
9 8 7 6 4 A‘ RxD-A receive signal A RS485
5 B‘ RxD-B receive signal B RS485
6 - VP Voltage supply +5 V (Imax=50 mA)
7 C/C‘ DGND Data reference potential
8 A TxD-A transmission signal A RS485
9 B TxD-B transmission signal B RS485
9-pole Sub-D socket 9-pole SUB-D connector
RS 232 cable 2 2
Part number PC 3 3 Operator
0058025-001D
5 7
Length 3 m
Housing (PE)
GB - 12

Operation of the Unit
3. Operation of the Unit

3.1 Keyboard
When switching on KEB COMBIVERT F5 the value of parameter CP.1 appears (see Drive mode to switch the
keyboard function).
The function key (FUNC) changes between the parameter

value and parameter number.
With UP (▲) and DOWN (▼) the value of the parameter

number is increased/decreased with changeable
parameters.
Principally during a change, parameter values are immediately accepted and stored non-volatile. However, with
some parameters it is not useful that the adjusted value is accepted immediately. In these cases (CP.28, CP.32,
CP.33, CP.34) the adjusted value is accepted and stored non-volatile by pressing ENTER.
If a malfunction occurs during operation, then the actual display is overwritten by the alarm message. The alarm
message in the display is reset by ENTER.
== Error ==>
With ENTER only the error message in the display is reset. In the inverter status display (CP.3) the
error is still displayed. In order to reset the error itself, the cause must be removed or a power-on
reset must be made.
GB - 10

3.2 Parameter Summary

Displ. Parameter Setting range Resolution Default Unit ↵ Based on
CP.00 Password Input 0…9999 1 - - - ud.1
CP.01 Encoder 1 speed ±4000 0.125 0 rpm - ru.9
CP.02 Setpoint display ±4000 0.125 0 rpm - ru.1
CP.03 Inverter state 0…255 1 0 - - ru.0
CP.04 Apparent current 0…6553.5 0.1 0 A - ru.15
CP.05 Peak apparent current 0…6553.5 0.1 0 A - ru.16
CP.06 Actual torque ±10000.00 0.01 0 Nm - ru.12
CP.07 Actual DC voltage 0…1000 1 0 V - ru.18
CP.08 Peak DC voltage 0…1000 1 0 V - ru.19
CP.09 Output voltage 0…778 1 0 V - ru.20
CP.10 Speed control configuration 4…5 1 0 - - cs.0
CP.11 DSM rated torque 0,1…6553,5 0.1 LTK Nm - dr.27
CP.12 DSM rated speed 0…32000 1 LTK rpm - dr.24
CP.13 DSM rated frequency 0,0…1600,0 0.1 LTK Hz - dr.25
CP.14 DSM rated current 0,0…710,0 0.1 LTK A - dr.23
CP.15 DSM EMK 0…1000 1 LTK V - dr.26
CP.16 DSM winding inductance 0,01…500,00 0.01 LTK mH - dr.31
CP.17 DSM winding resistance 0,000…50,000 0.001 LTK Ohm - dr.30
CP.18 DSM current for zero speed 0,0…700,0 0.1 LTK A - dr.28
CP.19 Load motor dependent parameter 1…2 1 1 - E fr.10
CP.20 System position 0…65535 1 57057 - - ec.2
CP.21 Rotation change 0…19 1 0 - - ec.6
CP.22 Maximum speed 0…4000 0.125 2100 rpm - op.10
CP.23 Fixed Speed 1 ±4000 0.125 100 rpm - op.21
CP.24 Fixed speed 2 ±4000 0.125 -100 rpm - op.22
CP.25 Acceleration time 0.00…300.00 0.01 5,00 s - op.28
CP.26 Deceleration time -0.01…300.00 0.01 5,00 s - op.30
CP.27 S-curve time 0.00…5.00 0.01 0,00 s - op.32
CP.28 Torque reference source 0…5 1 2 - E cs.15
CP.29 Absolute torque reference ±10000.00 0.01 LTK Nm - cs.19
CP.30 KP speed 0…32767 1 300 - - cs.6
CP.31 KI speed 0…32767 1 100 - - cs.9
CP.32 Switching frequency 2/4/8/12/16 - LTK kHz E uf.11
CP.33 Relay output 1 / Function 0…84 1 4 - E do.2
CP.34 Relay output 2 / Function 0…84 1 2 - E do.3
CP.35 Reaction to limit switch 0…6 1 6 - - pn.7
CP.36 Response of external fault 0…6 1 0 - - pn.3
LTK) depending on power circuit or on size (see 3.7 „Standard motor data“)
Due to the calculation / measuring accuracies, tolerances with the current and torque displays as well as with
the switching levels and limitations, must be taken into consideration.
Dependent on the data from the motor manufacturer, larger tolerances at the torque displays are possible, due
to the usual variations in the machine parameters and temperature drifts.
GB - 14
3.2.1 Password Input

CP.00 Password Input
Ex works the frequency inverter is supplied without password protection, this means that all changeable parameters
can be adjusted. After parameterizing the unit can be barred against unauthorized access (Passwords: see last
but one page). The adjusted mode is stored.
ENTER
Password
Barring the CP-Parameter

UP
FUNC
ENTER
Password
Enabling the CP-Parameter

UP
FUNC
3.2.2 Operating Display

The parameters below serve for the controlling of the frequency inverter during operation.
CP.01 Encoder 1 speed
Co-domain Description
0…±4000 rpm Display of actual motor speed ( incremental encoder 1). For control reasons the set speed
is displayed, even if the control release or direction of rotation are not switched. A counter-
clockwise rotating field (reverse) is represented by a negative sign. Precondition for the
correct display value is the in-phase connection of the motor and the correct setting of the
encoder line number (CP.20) as well as the direction of rotation (CP.21).
CP.02 Setpoint display
0…±4000 rpm Display of actually set value. For control reasons the set speed is displayed, even if the
control release or direction of rotation are not switched. If no direction of rotation is set,
the set speed for clockwise rotation (forward) is displayed.
CP.03 Inverter status

The status display shows the actual working conditions of the inverter. Possible displays and their meanings are:
„no Operation“ control release not bridged; modulation switched off; output voltage = 0 V; drive
is not controlled.
„Low Speed“ no direction of rotation preset; modulation switched off; output voltage = 0 V; drive
is not controlled.
"Forward Acceleration" drive accelerates with direction of rotation forward.
further on next side
GB - 15
„Forward Deceleration“ drive decelerates with direction of rotation forward.
"Reverse Acceleration" drive accelerates with direction of rotation reverse.
"Reverse Deceleration" drive decelerates with direction of rotation reverse.
"Forward Constant" drive runs with a constant speed and direction of rotation forward.
"Reverse Constant" drive runs with constant speed and direction of rotation reverse.
Other status messages are described at the parameters, where they occur (see chapter 4 „Error diagnosis“).
CP.04 Apparent current
0…±6553.5 A Display of the actual apparent current in ampere.
CP.05 Apparent current / peak value
0…±6553.5 A CP.5 makes is possible to recognize the max. apparent current. For that the highest value
of CP.4 is stored in CP.5 . The peak value memory can be cleared by pressing the UP,
DOWN or ENTER key or over bus by writing any value you like to the address of CP.5.
The switch off of the inverter also clears the memory.
CP.06 Actual torque
0.0…±10000.00 A The displayed value corresponds to the actual motor torque in Nm. The value is calculated
from the active current. Because of normal type differences and temperature deviations of
the motors, tolerances of up to 30 % are possible in the base speed range (see reference
at 3.2).
Requirement for the torque display is the adjustment of the motor data (CP.11...CP.16).
If the real motor data deviate strongly from the data on the name plate the operating
performance can be optimized by entering the real data. The adjustment of the name
plate data is sufficient for a start-up.
CP.07 Intermediate circuit voltage
Display Description
0…1000 V Display of actual DC-link voltage in volt. Typical values:
V-class Normal operation Overvoltage (E.OP) Undervoltage (E.UP)
230 V 300…330 V DC approx. 400 V DC approx. 216 V DC
400 V 530…620 V DC approx. 800 V DC approx. 240 V DC
CP.08 DC-link voltage / peak value
Display Description
0…1000 V CP.8 makes it possible to recognize short-time voltage rises within an operating cycle. For
that the highest value of CP.7 is stored in CP.8. The peak value memory can be cleared
by pressing the UP, DOWN or ENTER key or over bus by writing any value you like to the
address of CP.8. The switch off of the inverter also clears the memory.
GB - 16
CP.09 Output voltage
0…778 V Display of the actual output voltage in volt.
3.2.3 Basic Adjustment of the Drive

The following parameters determine the fundamental operating data of the drive and must be adjusted for the
initial commissioning (see chapter 5 "Start-up" ). They should be checked and/or adapted to the application.
CP.10 Speed control configuration
Input Setting Function Description

4 x Speed control (closed loop operation) With this parameter the basic setting of
5 Torque control (closed loop operation) the speed controller is determined.
CP.11…CP.18 Motor data

Under these parameters the motor data can be read off and adjusted. If you have purchased the servo controller
with motor from KEB, the optimal motor data are already adjusted and do not need to be changed anymore. The
parameter data can be taken from the parameter survey.
CP.19 Load motor dependent parameter

Ex factory the frequency inverter is adapted to the supplied motor (see chapter 3.3). If the motor data in CP.11…18
are changed, then CP.19 must be activated once. This re-adjusts the current controller, torque curve and torque
limit. With this, the torque limit is set at the value, that is maximally possible in the speed range (depending on
inverter rated current), but not above the rated motor torque x 3.
Co-domain Setting Description
1 x Pre-adjustment of the motor-dependent control-parameters.
The voltage class of the inverter is taken as input voltage.
2 Pre-adjustment of the motor-dependent control-parameters.
The measured DC-link voltage divided by √2 measured at switch on is taken
as input voltage. Thus the frequency inverter can be adapted to the actually
available mains voltage (e.g. USA with 460 V).
When control release is active the adjustment was not completed. „nco“ appears in the
display.
GB - 17
CP.20 System position

The system position of the attached resolver system is adjusted at this parameter (factory setting). With this
parameter it is possible to adjust the controller to a not aligned motor. If the ystem position of the motor is unknown
an automatic trimming can be done.
Before starting with the trimming, the direction of rotation must be checked. The speed display at CP.1 must be
positive when the engine runs manual in clockwise direction. If that is not the case, the direction of rotation can
be exchanged as described with CP.21. If the correct direction of rotation is displayed, it can be started with the
adjustment:
• the connected motor must be able to rotate freely

• open control release (terminal X2A.16)
• set CP.20 = 2206
• close control release (terminal X2A.16)
Now the motor is excited with its rated current and aligned to its zero position. The adjustment is finished when
the displayed system position at CP.20 does not change for approx. 5 s. In this case open control release and
switch off the unit.
If the error message E.EnC is displayed during trimming the direction of rotation must be checked (CP.21). In this
case the position trimming must be repeated.
In case that motors with aligned encoder system are used, the value which has been established by the automatic
trimming, can be entered under CP.20 as well. The adjustment values of known motors of the KEB COMBIVERT
S4 series must be multiplied by the pole-pair number of the motor.
Setting range Description

0…65535 The input value is a decimal value. The factory setting is 0.
Example 1:
6-pole motor (3 pole pairs) has a system position of 19.019 dec. with a S4-servo controller.
19019 dec. = 4A4Bh

4A4Bh x 3 pole pairs = DEE1h
DEE1h = 57057 dec.
If the value exceeds 65535 dec., the lower 16 bit of the hexadecimal result must be entered.
Example 2:
6-pole motor (3 pole pairs) has a system position of 23497 dec. with a S4-servo controller.
23497 dec. = 5BC9h
5BC9h x 3 pole pairs = 1135Bh
1135Bh = 70491 dec.
135Bh = 4955 dec.
GB - 18
CP.21 Rotation change
Value Setting Function Description

Encoder rotation The speed display at CP.1 must be positive when the engine runs
0 x no change manual in clockwise direction. The signals SIN+ and SIN- of the
1 track exchanged resolver have to be changed, if the sign is wrong. Please ensure
Options that the signals are not short-circuited with the internal shield (see
0 x no change connection resolver). The signals A(+) and A(-) must be changed for
2…15 reserved units with SIN/COS encoder.
Should this involve too much effort then you can achieve a rotation
Encoder system
reversal of encoder 1 by means of this parameter.
0 x no change
16 inverted
GB - 19
Parameter description
3.2.4 Special Adjustments

The following parameters serve for the optimization of the drive and the adaption to certain applications. These
adjustments can be ignored at the initial start-up.
CP.22 Maximum speed

0…4000 rpm 2100 rpm In order to limit the setpoint value a maximum speed must be preset. This limit
value is the basis for further setpoint calculations and for the determination
of setpoint characteristics. The maximum speed limits the setpoint speed
only. Because of speed ripples, speed overshoot or hardware defects (e.g.
defective encoder) the actual speed may exceed these limits.
CP.23 Fixed speed 1 (input 1)
CP.24 Fixed speed 2 (input 2)
Co-domain SettingDescription
CP.23 100 rpm Two fixed speeds can be adjusted. The selection is made by the
0…±4000 rpm inputs I1 and I2. If adjustments are made that are outside the fixed
CP.24 -100 rpm limit of CP.22, then the speed is internally limited.
Input I1 + input I2 = fixed speed 3 (factory setting = 0 rpm)
The Step speed 3 cannot adjusted in the CP-mode.
CP.25 Acceleration time

0.00…300.00 s 5.00 s Defines the time needed to accelerate from 0 to 1000 rpm. The actual
acceleration time is proportional to the speed change (∆n).
∆n Speed change n [rpm]
∆t Acceleration time for ∆n
1000
800
∆n
300
∆t
0 t [s]
0,5 1 1,5 2
CP.25
Example The drive should accelerate from 300 rpm auf 800 rpm in 1 s.
∆n = 800 rpm - 300 rpm = 500 rpm

∆t = 1 s
∆t 1s
CP.25 = –––– x 1000 rpm = –––––––– x 1000 rpm = 2 s
∆n 500 rpm
GB - 20

CP.26 Deceleration time

-0.01…300.00 s 5.00 s Defines the time needed to accelerate from 1000 to 0 rpm. The actual
deceleration time is proportional to the speed change (∆n). At a
deceleration time of -1 the value from CP.25 is used (Display „=Acc“) !
∆n Speed change n [rpm]
∆t Deceleration time for ∆n
1000
∆t
800
∆n
300
0 t [s]
0,5 1 1,5 2
CP.26
Example The drive should decelerate from 800 rpm to 300 rpm in 1 s.
∆n = 800 rpm - 300 rpm = 500 rpm

∆t = 1 s
∆t 1s
CP.26 = –––– x 1000 rpm = –––––––– x 1000 rpm = 2 s
∆n 500 rpm
CP.27 S‑curve time

0.00 (off)…5.00 s 0.00 s (off) For some applications it is of advantage when the drive starts and stops
t1 S-curve time (CP.27) jerk-free. This is achieved through a straightening of the acceleration and
t2 Acceleration time (CP.25) deceleration ramps. The straightening time, also called S-curve time, can
t3 Deceleration time (CP.26) be adjusted with CP.27.
+n [rpm]
t2 t3
t1 t1 t1 t1
t [s]
t1 t1 t1 t1
t2 t3
-n [rpm]
In order to drive defined ramps with activated S‑curve time, the acceleration and deceleration times
(CP.25 and CP.26) must be adjusted higher than the S‑curve time (CP.27).
GB - 21

CP.28 Torque reference source
Value Source Setting range Description

0 AN1+ / AN1- 0 %…±100 % = 0…±CP.29
1 AN2+ / AN2- 0 %…±100 % = 0…±CP.29 With this parameter the required setpoint source
2 digital absolute CP.29 for torque control can be adjusted.
3…5 only application mode
The values must be confirm by „ENTER“.
CP.29 Absolute torque reference

+10000.00 Nm see 3.3 The absolute torque reference of the drive is adjusted with parameter CP.29 in
torque controlled operation (CP.10 = 5) and with digital setpoint setting (CP.28
= 2). The sign stands for direction of rotation to be active.
In speed controlled operation (CP.10 = 4) the parameter works as torque limit
in all quadrants. The sign has no effect at that.
The factory setting depends on the unit size (see 3.3 „Factory Settings“).
During controlled operation (CP....10) this parameter has no function.
Because of normal type differences and temperature deviations of the motors, tolerances
of up to 30% are possible in the base speed range (see reference on page 13).
CP.30 KP speed

0…32767 300 The proportional factor of the speed controller is adjusted in these parameters
(see chapter 5 „Start-up“).
CP.31 KI speed

0…32767 100 The integral factor of the speed controller is adjusted in these parameters (see
chapter 5 „Start-up“).
CP.32 Switching frequency

2 / 4 / 8 / 12 / 16 kHz dependend The switching frequency with which the power modules are clocked can
of the be changed depending on the application. The employed power stage
power determines the maximum switching frequency as well as the factory setting
circuit (see manual:part 2). The values must be confirm by „ENTER“.
Refer to following list to learn low switching frequency high switching frequency
about influences and effects of the less inverter heating less noise development
switching frequency. less discharge current improved sine-wave simulation
less switching losses less motor losses
less radio interferences improved controller characteristics
improved concentricity with low
speed (only open loop!)
At switching frequencies above 4 kHz pay absolute attention to the max. motor line length
in the technical data of the power circuit manual (Part 2).
CP.33 Relay output 1 / function
CP.34 Relay output 2 / function

CP.33 and CP.34 determine the function of the two relay outputs (terminals X2A.24…26 and X2A.27…29). The
values must be confirm by „ENTER“.
GB - 22

Value Function
0 No function (generally off)
1 Generally on
2 Run signal; also by DC-braking
3 Ready signal (no error)
4 Fault relay
5 Fault relay (not at under voltage error)
6 Warning or error message at abnormal stopping
7 Overload alert signal
8 Overtemperature alert signal power modules
9 External overtemperature alert signal motor
10 Only application mode
11 Overtemperature alert signal interior OHI
12…19 Only application mode
20 Actual value = set value (CP.3 = Fcon; rcon; not at noP, LS, error, SSF)
21 Accelerate (CP.3 = FAcc, rAcc, LAS)
22 Decelerate (CP.3 = FdEc, rdEc, LdS)
23 Real direction of rotation = set direction of rotation
24 Utilization > switching level 1)
25 Active current > switching level 1)
27 Real value (CP.1) > switching level 1)
28 Setpoint (CP.2) > switching level 1)
31 Absolute setpoint at AN1 > switching level 1)
32 Absolute setpoint at AN2 > switching level 1)
34 Setpoint at AN1 > switching level 1)
35 Setpoint at AN2 > switching level 1)
40 Hardware current limit activated
41 Modulation on-signal
47 Ramp output value > switching level 1)
48 Apparent current (CP.4) > switching level 1)
49 Forward running (not at nOP, LS, abnormal stopping or error)
50 Reverse running (not at nOP, LS, abnormal stopping or error)
51 Warning E.OL2
52 Current regulator limit reached
53 Speed regulator limit reached
63 Absolute value ANOUT1 > switching level 1)
64 Absolute value ANOUT2 > switching level 1)
65 ANOUT1 > switching level 1)
66 ANOUT2 > switching level 1)
70 Driving current active (safety relay)
73 Absolut active power > switching level 1)
74 Active power > switching level 1)
80 Active current > switching level 1)
GB - 23

Value Function
81 Real value channel 1 > switching level 1)
82 Real value channel 2 > switching level 1)
83 HSP5 bus synchronized
1) Switching level of CP.33 = 100; switching level of CP.34 = 4
GB - 24

CP.35 Limit switch / stopping mode

This parameter determines the reaction of the drive, to terminal X2A.14 (F) and/or X2A.15 (R). These terminals
are programmed as limit switches. The reaction of the drive is shown in the table below.
Value Setting Display Reaction Restart
0 E.PRx Immediate disabling of modulation
Quick stopping / disabling of modulation after reaching Remove fault,
1 A.PRx
speed 0 reset
2 A.PRx Quick stopping / holding torque at speed 0
3 A.PRx Immediate disabling of modulation
Quick stopping / disabling of modulation after reaching Autoreset, if no fault
4 A.PRx
speed 0 is present
6 x — No effect to the drive, fault is ignored ! —
CP.36 Reaction to external fault

With the external error monitoring external units can take direct influence on the drive. This parameter determines
the response of the drive to a signal at terminal X2A.12 (I3) according to following table.
Value Setting Display Reaction Restart
0 x E.PRx Immediate disabling of modulation
Quick stopping / disabling of modulation after reaching Remove fault,
1 A.PRx
speed 0 reset
3 A.PRx Immediate disabling of modulation
Quick stopping / disabling of modulation after reaching Autoreset, if no fault
4 A.PRx
speed 0 is present
6 — No effect to the drive, fault is ignored ! —
GB - 25

3.3 Motor data (factory setting)

The following table contains the motor data of standard motors.
Parameter CP.11 CP.12 CP.13 CP.14 CP.15 CP.16 CP.17 CP.18 CP.29
DSM EMK voltage constant
DSM winding inductance
DSM winding resistance

Rated motor frequency
Rated motor current

Rated motor torque
Rated motor speed
Stand still current
Maximum torque
Default motor
voltage class
Unit size/
[Nm] [rpm] [Hz] [A] [V/1000rpm] mH Ω [A] [Nm]

09/200V C3.SM.000-3200 3,9 3000 150 4,20 69 6,9 2,0 5,1 22,09
10/200V C4.SM.000-3200 5 3000 150 5,7 68 4.5 1,2 7,1 30,68
12/200V D2.SM.000-3200 6,1 3000 150 8,1 67 4 1 8,5 53,53
13/200V D3.SM.000-3200 8,4 3000 150 10,9 69 2.8 0,6 12,4 69,92
14/200V E4.SM.000-3200 15,5 3000 150 16 89 1,3 0,29 27,8 93,40
09/400V C3.SM.000-3400 3,9 3000 150 2,4 118 20,6 5,9 2.9 22,47
10/400V C4.SM.000-3400 5 3000 150 3,4 113 13,1 3,4 4,2 30,81
12/400V D2.SM.000-3400 6,1 3000 150 4.5 119 12,8 3.2 4,8 53,21
13/400V D4.SM.000.3400 9,9 3000 150 7,3 121 1,5 1,4 8,5 73,26
14/400V E2.SM.000-3400 11 3000 150 7 136 8.2 2 9 80,12
15/400V E4.SM.000-3400 15,5 3000 150 9,9 143 3,4 0,81 17,3 118,83
16/400V F1.SM.000-3400 20 1465 150 13,8 130 7 0,58 17 165,99
17/400V F2.SM.000-3400 31 3000 150 20,6 135 3.6 0,23 32,2 213,37
18/400V F3.SM.000-3400 33 3000 150 22,9 131 1,7 0,13 46,2 253,27
GB - 26
Drive mode
3.4 Drive mode

The Drive Mode is an operating mode of KEB COMBIVERT that permits the manual starting of the drive by the
operator (with exception of the LCD Operator). After switching the control release the set value and rotation setting
are effected exclusively over the keyboard. In order to activate the drive mode the corresponding password (see
last but one page) must be entered in CP. 0. The display switches over as follows:
Direction of rotation Status

F = clockwise rotation noP = no control release
r = counter clockwise rotation LS = neutral position
3.4.1 Start / stop drive Modulation blocked

Drive decreases to 0
rpm and switches the
Drive not controlled
modulation off
Drive accelerates onto the Drive operates with

adjusted set value adjusted set value
3.4.2 Changing the
Drive changes
direction of direction of rotation
rotation
3.4.3 Presetting the Display changes when

setpoint key is pressed to set value
display/presetting
Set value can be changed
with UP/DOWN at pressed
FUNC/SPEED key
3.4.4 Leaving the drive To exit the drive mode the inverter must be in status “stop” (Display noP or LS).
mode Press the FUNC and ENTER keys simultaneously for about 3 seconds to leave the
drive mode. The CP-parameters appear in the display.
+ for 3 seconds
GB - 24

Error Assistance
4. Error Assistance
At KEB COMBIVERT error messages are always represented with an "E." and the appropriate error in the
display. Error messages cause the immediate deactivation of the modulation. Restart possible only after reset or
autoreset.
Malfunction are represented with an „A.“ and the appropriate message. Reactions to malfunctions can vary. In the
following the display and their cause are described.
Display COMBIVIS Value Meaning

Status Messages
bbL base block 76 Power modules for motor de-excitation locked
bon close brake 85 Brake control, brake engaged (see chapter 6.9)
boFF open brake 86 Brake control, brake released (see chapter 6.9)
Cdd calculate drive 82 Measurement of the motor stator resistance.
dcb DC brake 75 Motor is decelerated by a DC-voltage at the output.
Modulation is switched off after DC-braking (see chapter 6.9 "DC-
dLS low speed / DC brake 77
Braking“).
FAcc forward acceleration 64 Acceleration with the adjusted ramps in clockwise direction of rotation.
Acceleration / deceleration phase is completed and it is driven with
Fcon forward constant 66
constant speed / frequency in clockwise direction of rotation.
It is stopped with the adjusted ramp times in clockwise direction of
FdEc forward deceleration 65
rotation.
The message is output if the output current reaches the hardware
HCL hardware current limit 80
current limit.
This message is displayed if during acceleration the load is limited to the
LAS LA stop 72
adjusted load level.
This message is displayed if during deceleration the load is limited to the
LdS Ld stop 73
adjusted load level or the DC-link current to the adjusted voltage level.
LS low speed 70 No direction of rotation pre-set, modulation is off.
nO_PU power unit not ready 13 Power circuit not ready or not identified by the control.
noP no operation 0 Control release (terminal ST) is not switched.
PA positioning active 122 This message is displayed during a positioning process.
PLS low speed / power off 84 No modulation after Power-Off.
The specified position cannot be reached within the pre-set ramps. The
PnA position not reachable 123
abort of the positioning can be programmed.
Depending on the programming of the function (see chapter 6.9 „Power-
POFF power off function 78 off Function) the inverter restarts automatically upon system recovery or
after a reset.
POSI positioning 83 Positioning function active (F5-G).
Acceleration with the adjusted ramp times in anti-clockwise direction of
rAcc reverse acceleration 67
rotation.
Acceleration / deceleration phase is completed and it is driven with
rcon reverse constant 69
constant speed / frequency in clockwise direction of rotation.
It is stopped with the adjusted ramp times in anti-clockwise direction of
rdEc reverse deceleration 68
rotation.
rFP ready for positioning 121 The drive signals that it is ready to start the positioning process.
This message is displayed if during constant operation the load is limited
SLL stall 71
to the adjusted current limit.
SrA search for ref. active 81 Search for reference point approach active.
Speed search function active, that means that the inverter attempts to
SSF speed search 74
synchronize onto a running down motor.
The message is output if as response to a warning signal the quick-stop
STOP quick stop 79
function becomes active.
GB - 25

Error Assistance

Error Messages
Error: can occur in the case of switched on brake control (see chapter
6.9.5), if
E. br Error ! brake 56 the load is below the minimum load level (Pn.43) at start up or the
absence of an engine phase was detected
the load is too high and the hardware current limit is reached
Adjusted monitoring time (Watchdog) of communication between
E.buS Error ! Watchdog 18
operator and PC / operator and inverter has been exceeded.
E.Cdd Error ! calc. drive data 60 Error: During the automatic motor stator resistance measurement.
E.co1 Error ! counter overrun 1 54 Counter overflow encoder channel 1.
E.co2 Error ! counter overrun 2 55 Counter overflow encoder channel 2.
Error: Overtemperature of motor PTC. Error can only be reset at E.ndOH,
if PTC is again low-resistance. Causes:
E.dOH Error ! drive overheat 9 resistance at the terminals T1/T2 >1650 Ohm
motor overloaded
line breakage to the temperature sensor
Error: Driver relay. Relay for driver voltage on power circuit has not
E.dri Error ! driver relay 51
picked up even though control release was given.
After reset the operation is again possible (without storage in the
E.EEP Error ! EEPROM defective t 21
EEPROM)
Error: External error. Is triggered, if a digital input is being programmed
E. EF Error ! external fault 31
as external error input and trips.
E.EnC Error ! Encoder cable 32 Cable breakage at the resolver or incremental encoder
E.Hyb Error ! hybrid 52 Invalid encoder interface identifier.
Error: Encoder interface identifier has changed, it must be confirmed
E.HybC Error ! hybrid changed 59
over ec.0 or ec.10.
Hardware failure at the NPN/PNP change-over or at the start/stop
E.iEd Error ! input error detect 53
measurement.
E.InI Error ! initialisation MFC 57 MFC not booted.
Load-shunt relay has not picked up. occurs for a short time during the
switch-on phase, but must automatically be reset immediately. If the
error message remains the following causes may be applicable:
load-shunt defective
E.LSF Error ! load shunt fault 15
input voltage wrong or too low
high losses in the supply cable
braking resistor wrongly connected or damaged
braking module defective
Motor temperature switch or PTC at the terminals T1/T2 is again in the
E.ndOH no ERROR drive overheat 11
normal operating range. The error can be reset now.
Temperature of the heat sink is again in the permissible operating range.
E.nOH no E. over heat pow.mod. 36
The error can be reset now.
No longer overheating in the interior E.OHI, interior temperature has
E.nOHI no ERROR overheat int. 7
fallen by at least 3°C
No more overload, OL-counter has reached 0%; after the error E.OL a
cooling phase must elapse. This message appears upon completion of
E.nOL no ERROR overload 17
the cooling phase. The error can be reset now. The inverter must remain
switched on during the cooling phase.
E.nOL2 no ERROR overload 2 20 The cooling time has elapsed. The error can be reset.
GB - 26

Error Assistance

Occurs, if the specified peak current is exceeded. Causes:
acceleration ramps too short
the load is too big at turned off acceleration stop and turned off constant
current limit
short-circuit at the output
E. OC Error ! overcurrent 4
short-circuit at the output
deceleration ramp too short
motor cable too long
EMC
DC brake at high ratings active (see 6.9.3)
Error: Overtemperature of power module. Error can only be reset at
E.nOH. Causes:
E. OH Error ! overheat pow.mod. 8 insufficient air flow at the heat sink (soiled)
ambient temperature too high
ventilator clogged
E.OH2 Error ! motor protection 30 Electronic motor protective relay has tripped.
Error: Overheating in the interior: error can only be reset at E.nOHI, if
E.OHI Error ! overheat internal 6
the interior temperature has dropped by at least 3 °C.
Error: Overload error can only be reset at E.nOL, if OL-counter reaches
0% again. Occurs, if an excessive load is applied longer than for the
permissible time (see technical data). Causes:
poor control adjustment (overshooting)
E. OL Error ! overload (Ixt) 16
mechanical fault or overload in the application
inverter not correctly dimensioned
motor wrongly wired motor wrongly wired
encoder damaged
Occurs if the standstill constant current is exceeded (see technical data
E.OL2 Error ! overload 2 19 and overload characteristics). The error can only be reset if the cooling
time has elapsed and E.nOL2 is displayed.
Voltage in the DC-link circuit too high. Occurs when the DC bus voltage
rises above the permissible value. Causes:
poor controller adjustment (overshooting)
E. OP Error ! Overvoltage 1 input voltage too high
interference voltages at the input
deceleration ramp too short
braking resistor defective or too small
E.OS Error ! over speed 58 Real speed is bigger than the max. output speed.
E.PFC Error ! Power factor control 33 Error in the power factor control
The drive has driven onto the right limit switch. Programmed response
E.PrF Error ! prot. rot. for. 46 „Error, restart after reset” (see chapter 6.7 „Response to errors or
warning messages”).
The drive has driven onto the left limit switch. Programmed response
E.Prr Error ! prot. rot. rev. 47 „Error, restart after reset” (see chapter 6.7 „Response to errors or
warning messages”).
E. Pu Error ! power unit 12 Error: General power circuit fault
Error: During the initialization the power circuit could not be recognized
E.Puci Error ! Unknown power unit 49
or was identified as invalid.
GB - 27

Error Assistance

Error: Power circuit identification was changed; with a valid power circuit
this error can be reset by writing to SY.3. If the value displayed in SY.3
E.Puch Error ! power unit changed 50 is written, only the power-circuit dependent parameters are reinitialized.
If any other value is written, then the default set is loaded. On some
systems after writing Sy.3 a Power-On-Reset is necessary.
Error ! Power unit Error: Parameter value could not be written to the power circuit.
E.PUCO 22
communication Acknowledgement from LT <> OK
Error: Software version for power circuit and control card are different.
E.PUIN Error ! Power unit invalid 14
Error cannot be reset (only at F5-G B-housing)
Sychronization over sercos-bus not possible. Programmed response
E.SbuS Error ! bus synchron 23
„Error, restart after reset”.
It has been attempted to select a locked parameter set. Programmed
E.SEt Error ! set 39
response „Error, restart after reset”.
Error ! Software limit switch The target position lies outside of the limit defined with the right software
E.SLF 44
forward limit switch. Programmed response „Error, restart after reset”.
Error ! Software limit switch The target position lies outside of the limit defined with the left software
E.SLr 45
reverse limit switch. Programmed response „Error, restart after reset”.
Error: Undervoltage (DC-link circuit) Occurs, if DC-link voltage falls
below the permissible value. Causes:
input voltage too low or instable
inverter rating too small
voltage losses through wrong cabling
the supply voltage through generator / transformer breaks down at very
E. UP Error ! underpotential 2
short ramps
at F5-G housing B E.UP is also displayed if no communication takes
place between power circuit and control card.
jump factor (Pn.56) too small
if a digital input was programmed as external error input with error
message E.UP (Pn.65).
E.UPh Error ! Phase failure 3 One phase of the input voltage is missing (ripple-detection)
Warning Messages
Warning: Watchdog for communication between operator/control card
A.buS Warning ! Watchdog 93 or operator/PC has responded. The response to this warning can be
programmed.
The motor temperature has exceeded an adjustable warning level.
The switch off time is started. The response to this warning can be
A.dOH Warning ! drive overheat 96
programmed. This warning can be generated only with a special power
circuit.
This warning is triggered via an external input. The response to this
A. EF Warning ! external fault 90
warning can be programmed.
The motor temperature is again below the adjusted warning level. The
A.ndOH All-clear ! drive overheat 91
switch off time is stopped.
All-clear ! overheat pow.
A.nOH 88 The heat sink temperature is again below the adjusted warning level.
mod.
The temperature in the interior of the inverter is again below the warning
A.nOHI All-clear ! overheat internal 92
threshold.
A.nOL All-clear ! overload 98 OL counter has reached 0 %, the warning “overload“ can be reset.
The cooling time after “Warning ! Overload during standstill" has elapsed.
A.nOL2 All-clear ! overload 2 101
The warning message can be reset.
Warning ! overheat pow. A level can be defined, when it is exceeded this warning is output. The
A. OH 89
mod. response to this warning can be programmed.
GB - 28

Error Assistance

Warning: electronic motor protective relay has tripped. The response to
A.OH2 Warning ! motor protection 97
this warning can be programmed.
The temperature in the interior of the inverter lies above the permissible
A.OHI Warning ! overheat internal 87 level. The switch off time was started. The programmed response to this
warning message is executed.
A level between 0 and 100 % of the load counter can be adjusted, when
A. OL Warning ! overload 99 it is exceeded this warning is output. The response to this warning can
be programmed.
The warning is output when the standstill continuous current is exceeded
(see technical data and overload characteristics). The response to this
A.OL2 Warning ! overload 2 100
warning can be programmed. The warning message can only be reset
after the cooling time has elapsed and A.nOL2 is displayed.
The drive has driven onto the right limit switch. The response to this
A.PrF Warning ! prot. rot. for. 94
The drive has driven onto the left limit switch. The response to this
A.Prr Warning ! prot. rot. rev. 95
Sychronization over sercos-bus not possible. The response to this
A.SbuS Warning ! synchron 103
It has been attempted to select a locked parameter set. The response to
A.SEt Warning ! set 102
this warning can be programmed.
Warning ! Software limit The target position lies outside of the limit defined with the right software
A.SLF 104
switch forward limit switch. The response to this warning can be programmed.
Warning ! Software limit The target position lies outside of the limit defined with the left software
A.SLr 105
switch reverse limit switch. The response to this warning can be programmed.
GB - 29

Error Assistance
GB - 30

Start-up
5. Initial Start-up
The speed controller must be adjusted when the KEB COMBIVERT F5-SERVO is taken into operation. By using
the software COMBIVIS a setvalue jump can be recorded. With the examples on the following page the speed
controller can be adjusted.
• Install COMBIVIS on the PC and startup. Select and startup the programm SCOPE.
• Parameterize SCOPE:
Operating mode: Offline

Time reference: 2ms
Trigger position: 5%
Trigger condition: Fixed speed input
Channel A: ru.01 Set speed
Channel B: ru.07 Actual speed
• Go in the operating mode of SCOPE, calibrate channels and adjust time reference (e.g. 50ms/DIV).
• Switch control release X2A.16
• Preset fixed speed (e.g.: 50% nominal)
• Activate a fixed speed with an programmable input, the KEB COMBIVERT executes a setpoint step change.
• Subsequently the data are read out with the aid of SCOPE and compare recorded step change with the examp-
les on the following page and adjust speed controller.
• Repeat step change and record again until a satisfying initial response and an optimal controller adjustment is
found.
Rough adjustment of the speed controller without using the SCOPE:

• Increase P-part to the stability limit (system starts to oscillate) and then decrease by 30%.
• Repeat the same procedure with the I-part
GB - 34

Start-up
6. Adjustment Speed Controller

With the PC software KEB COMBIVIS (Scope) set and real speed can be displayed. If one of the following real
speed curves occurs at acceleration, the speed controller (CP.30, CP.31) should be adjusted according to the
notes.
Problem Very long transient process Problem Very long speed overshoot
Solution Increase KP speed (CP.30); eventually Solution Increase KP speed (CP.30);
reduce KI speed (CP.31) eventually reduce KI speed (CP.31)
Problem Sustained oscillation short billowy, Problem Transient too slow / remaining system
noises, vibes deviation
Solution Decrease KP speed (CP.30) Solution Increase KI speed (CP.31)
Problem Overshoot too long, strong speed Problem Sustained oscillation long billowy
decreases at load change
Solution Increase KI speed (CP.31) Solution Reduce KI speed (CP.31) and / or

reduce KP speed (CP.30)
GB - 35

Quick Reference
7. Quick Reference
Displ. Parameter Setting range Resolution ↵ Customer setting

CP.00 Password Input 0…9999 1 -
CP.01 Encoder 1 speed ±4000 rpm 0.125 rpm -
CP.02 Setpoint display ±4000 rpm 0.125 rpm -
CP.03 Inverter state 0…255 1 -
CP.04 Apparent current 0…6553.5 A 0.1 A -
CP.05 Peak apparent current 0…6553.5 A 0.1 A -
CP.06 Actual torque ±10000.00 Nm 0.01 Nm -
CP.07 Actual DC voltage 0…1000 V 1 V -
CP.08 Peak DC voltage 0…1000 V 1 V -
CP.09 Output voltage 0…778 V 1 V -
CP.10 Speed control configuration 4…5 1 -
CP.11 DSM rated torque 0.1…6553.5 A 0.1 Nm -
CP.12 DSM rated speed 0…32000 rpm 1 rpm -
CP.13 DSM rated frequency 0.0…1600.0 Hz 0.1 Hz -
CP.14 DSM rated current 0.0…710.0 A 0.1 A -
CP.15 DSM EMK voltage constant 0…1000 V 1 V -
CP.16 DSM winding inductance 0.01…500.00 mH 0.01 mH -
CP.17 DSM winding resistance 0.000…50.000 Ω 0.001 Ω -
CP.18 DSM current for zero speed 0.0…700.0 A 0.1 A -
CP.19 Load motor dependent parameter 1…2 1 E
CP.20 System position 0…65535 1 -
CP.21 Rotation change 0…19 1 -
CP.22 Maximum speed 0…4000 rpm 0.125 rpm -
CP.23 Fixed Speed 1 ±4000 rpm 0.125 rpm -
CP.24 Fixed speed 2 ±4000 rpm 0.125 rpm -
CP.25 Acceleration time 0.00…300.00 s 0.01 s -
CP.26 Deceleration time -0.01…300.00 s 0.01 s -
CP.27 S-curve time 0.00…5.00 s 0.01 s -
CP.28 Torque reference source 0…5 1 E
CP.29 Absolute torque reference ±10000.00 Nm 0,01 Nm -
CP.30 KP speed 0…32767 1 -
CP.31 KI speed 0…32767 1 -
CP.32 Switching frequency 2/4/8/12/16 kHz - E
CP.33 Relay output 1 / Function 0…84 1 E
CP.34 Relay output 2 / Function 0…84 1 E
CP.35 Reaction to limit switch 0…6 1 -
CP.36 Reaction to external fault 0…6 1 -
GB - 36
Notes
GB - 37

Notes
GB - 38

Passwords
8. Passwords
Read only Read/Write Drive mode
100 200 500
GB - 35

Karl E. Brinkmann GmbH
Försterweg 36-38 • D-32683 Barntrup
fon: +49 5263 401-0 • fax: +49 5263 401-116
net: www.keb.de • mail: info@keb.de
KEB worldwide…
KEB Antriebstechnik Austria GmbH KEB (UK) Ltd.

Ritzstraße 8 • A-4614 Marchtrenk Morris Close, Park Farm Industrial Estate
fon: +43 7243 53586-0 • fax: +43 7243 53586-21 GB-Wellingborough, NN8 6 XF
net: www.keb.at • mail: info@keb.at fon: +44 1933 402220 • fax: +44 1933 400724
net: www.keb-uk.co.uk • mail: info@keb-uk.co.uk
KEB Antriebstechnik
Herenveld 2 • B-9500 Geraadsbergen KEB Italia S.r.l.
fon: +32 5443 7860 • fax: +32 5443 7898 Via Newton, 2 • I-20019 Settimo Milanese (Milano)
mail: vb.belgien@keb.de fon: +39 02 3353531 • fax: +39 02 33500790
net: www.keb.de • mail: kebitalia@keb.it
KEB Power Transmission Technology (Shanghai) Co.,Ltd.
No. 435 Qianpu Road, Chedun Town, Songjiang District, KEB Japan Ltd.
CHN-Shanghai 201611, P.R. China 15–16, 2–Chome, Takanawa Minato-ku
fon: +86 21 37746688 • fax: +86 21 37746600 J-Tokyo 108-0074
net: www.keb.de • mail: info@keb.cn fon: +81 33 445-8515 • fax: +81 33 445-8215
mail: info@keb.jp
KEB Antriebstechnik Austria GmbH
Organizační složka KEB Korea Seoul
K. Weise 1675/5 • CZ-370 04 České Budějovice Room 1709, 415 Missy 2000
fon: +420 387 699 111 • fax: +420 387 699 119 725 Su Seo Dong, Gang Nam Gu
mail: info.keb@seznam.cz ROK-135-757 Seoul/South Korea
fon: +82 2 6253 6771 • fax: +82 2 6253 6770
KEB Antriebstechnik GmbH mail: vb.korea@keb.de
Wildbacher Str. 5 • D–08289 Schneeberg
fon: +49 3772 67-0 • fax: +49 3772 67-281 KEB RUS Ltd.
mail: info@keb-drive.de Lesnaya Str. House 30, Dzerzhinsky (MO)
RUS-140091 Moscow region
KEB España fon: +7 495 632 0217 • fax: +7 495 632 0217
C/ Mitjer, Nave 8 - Pol. Ind. LA MASIA net: www.keb.ru • mail: info@keb.ru
E-08798 Sant Cugat Sesgarrigues (Barcelona)
fon: +34 93 897 0268 • fax: +34 93 899 2035 KEB Sverige
mail: vb.espana@keb.de Box 265 (Bergavägen 19)
S-43093 Hälsö
Société Française KEB fon: +46 31 961520 • fax: +46 31 961124
Z.I. de la Croix St. Nicolas • 14, rue Gustave Eiffel mail: vb.schweden@keb.de
F-94510 LA QUEUE EN BRIE
fon: +33 1 49620101 • fax: +33 1 45767495 KEB America, Inc.
net: www.keb.fr • mail: info@keb.fr 5100 Valley Industrial Blvd. South
USA-Shakopee, MN 55379
fon: +1 952 224-1400 • fax: +1 952 224-1499
net: www.kebamerica.com • mail: info@kebamerica.com
More and latest addresses at http://www.keb.de
© KEB
Mat.No. 00F5SEB-K320
Rev. 2E
Date 06/2014

Combivert f5 Series

Uploaded by

Copyright:

Available Formats

Combivert f5 Series

Uploaded by

Document Information

Original Title

Copyright

Available Formats

Share this document

Share or Embed Document

Sharing Options

Did you find this document useful?

Is this content inappropriate?

Copyright:

Available Formats

Combivert f5 Series

Uploaded by

Copyright:

Available Formats

COMBIVERT

GB INSTRUCTION MANUAL Control Circuit from V3.2

Downloaded from www.Manualslib.com manuals search engine

Downloaded from www.Manualslib.com manuals search engine

2. Installation and Connection........................... 5

3. Operation of the Unit..................................... 13

6. Adjustment Speed Controller....................... 35

2. Installation and Connection

2.1.2 Housing Size >= G

Observe the maximal width of

2.2 Control board Servo X2A

PIN Function Name Description

2.2.2 Connection of the control circuit

2.2.3 Digital Inputs

Using of an external voltage supply

2.2.4 Analog Inputs

2.2.5 Voltage Input / External Power Supply

2.2.6 Digital Outputs

2.2.7 Relay Outputs

2.2.8 Analog Outputs

2.2.10 Motor connection

Observe correct phase sequence of the servo motor !

Servo motor A Brake + external brake supply

Motor housing / Connect shielding at both

2.2.11 Resolver connection X3A

2.2.12 incremental encoder simulation X3B

X3B PIN No. Signal

00.S4 . 019 - 0005

019 = Motor cable 1,5 mm²

00.F5 . 0C1 - 1005

Part 0C1 = Resolver cable

Max. Encoder cable lenght 50 m. Longer encoder cables on request.

Digital operator (part number 00.F5.060‑1000)

x x Double function keyboard

- x X6B HSP5 programming and diagnostic

X6C PIN RS485 Signal Meaning

9-pole Sub-D socket 9-pole SUB-D connector

Downloaded from www.Manualslib.com manuals search engine

3. Operation of the Unit

The function key (FUNC) changes between the parameter

With UP (▲) and DOWN (▼) the value of the parameter

Downloaded from www.Manualslib.com manuals search engine

3.2 Parameter Summary

3.2.1 Password Input

Barring the CP-Parameter

Enabling the CP-Parameter

3.2.2 Operating Display

CP.01 Encoder 1 speed

CP.02 Setpoint display

CP.03 Inverter status

further on next side

„Forward Deceleration“ drive decelerates with direction of rotation forward.

"Reverse Acceleration" drive accelerates with direction of rotation reverse.

"Reverse Deceleration" drive decelerates with direction of rotation reverse.

CP.04 Apparent current

CP.05 Apparent current / peak value

CP.06 Actual torque

CP.07 Intermediate circuit voltage

CP.08 DC-link voltage / peak value