Seals
Seals
Seals
Busak+ Shamban
1
Busak+ Shamban
2
Piston Seals
Contents
Choice of Sealing Element . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . Design Instructions . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . Installation of Piston Seals . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . TurconR Glyd RingR . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . TurconR Glyd RingR T . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . TurconR AQ-SealR 5 . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . TurconR AQ-SealR . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . POLYPACR PHD Seal . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . TurconR StepsealR 2K .................................................................... 4 8 10 15 23 31 39 47 53 61 69 77 83 93 99
TurconR StepsealR K . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . TurconR Double DeltaR . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . TurconR VarisealR M2 . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . ZurconR U-Cup PUA . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . ZurconR Wynseal . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . POLYPACR PHD/P . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .
Compact Seal DAS Type A/B - POLYPACR DBM . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 105 ZurconR Compact Seals PU DAS - POLYPACR EUD . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 113 Rubber Fabric Compact Seal POLYPACR DUOPAC DPS/DPC . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 119 POLYPACR Veepac CH/G1 . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 127 POLYPACR Selemaster DSM . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 131 Non Standard Seals . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 137
Busak+ Shamban
3
Piston Seals
Busak+ Shamban
4
Piston Seals
Field of Application
Heavy Double Light Single
Type
Page
Medium
ISO/DIN
mm
oC
m/s
MPa max.
D D D D
D D D D
60 60 20 8-2300 -45/ +100 -45/ 45/ +200 X 8-2300 -45/ +100 2 2 80 60 15 25 80 60 40-700 40 700 X -45/ +200 3 60
Turcon T46 Turcon T29 Turcon T05 Zurcon Z51 Turcon T46 Turcon T40 Zurcon Z51 Turcon T46 Turcon T10 Turcon T46 Turcon T10 PTFE Bronze + NBR + POM Turcon T46 Turcon T29 Zurcon Z51 Turcon T46 Turcon T29 Zurcon Z51
Mobile hydraulics Standard cylinders Machine tools Injection moulding machines Presses P Automotive industry Mobile hydraulic Holding cylinders Piston accumulators
D D D D D D
D D D D D D D D D
D D D D D D D D D 7425/1
8-2700 8 2700
Turcon AQ-Seal 5 31
Turcon AQ-Seal 39
D D
40 -45/ +200 2 40
D D D
D D D
Turcon Stepseal 2K 53
Mobile hydraulics Standard cylinders Machine tools Injection moulding machines Presses
D D D D D
D D D D D
D D D D D 7425/1
70 15 70 2 80 60 15 60 2 80
Turcon Stepseal K 61
Mobile hydraulics Standard cylinders Machine tools Injection moulding machines Presses
D D D D D
D D D D D
D D D D D 7425/1
-45/ +100
* The data below are maximum values and cannot be used at the same time. The max. pressure depends on temperature and gap dimension. ** Temperature Range is depending on choise of elastomer material and Media. In the case of Turcon seals in unpressurized applications in temperatures below 0C please contact our application engineers for assistance !
Busak+ Shamban
5
Piston Seals
Technical Data* Seal S l Application A li i Standard S d d Size Range Action A i Temp. Range** Speed Pressure Recommended Seal Material
Field of Application
Heavy Double Light Single
Type
Page
Medium
ISO/DIN
mm
oC
m/s
MPa max.
69
D D D D
20 35 25
Turcon T05 Turcon T46 Turcon T24 Turcon T40 Turcon T05
Turcon VarisealM2 77
D D D
D D D
45 -70/ +260 15 20
D D D
D D D
16-250 16 250
-35/ +110
0.5 05
40
Zurcon Z20
Zurcon Wynseal
D D
D D -35/ +110
25
93
7425/1
12-300
0.5 40
D D D
D D D
Zurcon Z20 + NBR + POM NBR + TPE + POM Zurcon Z20 + NBR + POM
D D D
D D D
D D D
D D D
6547
40-270 40 270
-35/ +110
0.5 05
40
* The data below are maximum values and cannot be used at the same time. The max. pressure depends on temperature and gap dimension. ** Temperature Range is depending on choise of elastomer material and Media.
Busak+ Shamban
6
Piston Seals
Technical Data* Seal S l Application A li i Standard S d d Size Range Action A i Temp. Range** Speed Pressure Recommended Seal Material
Field of Application
Heavy Double Light Single
Type
Page
Medium
ISO/DIN
mm
oC
m/s
MPa max.
D D D D
D D D D
D D D D
40-250 40 250
-30/ +130
0.5 05
40
D D D D
D D D D
D D D D
40-250 40 250
-30/ +200
0.5 05
40
D D D D
D D D D
D D D D
45-360
-30/ +130
0.5
70
* The data below are maximum values and cannot be used at the same time. The max. pressure depends on temperature and gap dimension. ** Temperature Range is depending on choise of elastomer material and Media.
Busak+ Shamban
7
Piston Seals
Design Instructions
Lead in chamfers Piston seals are always fitted with an interference fit. In order to avoid damage during installation, lead-in chamfers and rounded edges must be provided on the cylinder barrel (Figure 1). If this is not possible for design reasons, a separate installation tool must be used. The minimum lead-in chamfer depends on the profile size of the seal and can be seen from the following tables. Additionally it is recommended that the diameter increase D exceeds 0.015 x bore diameter. Table III Compact Seal and VarisealR
Compact Seal Groove Depth* 3.5 4.0 5.0 7.5 10.0 12.5 15.0 20.0 PVA4 PVA5 PVA3 PVA0 PVA1,PVA2 TurconR VarisealR M2 Series
Lead-in Chamfer Diameter increase DN min. 1.1 1.1 1.4 2.2 2.7 3.5 4.0 5.5 6.5 9.5
* The groove depth is calculated as (D - D1)/2. The dimensions for D and D1 can be found in the tables Installation dimensions, from chapter Compact Seal DAS and DBM.
Table IV
Double DeltaR
O-Ring Cross Section** d2 1.78 2.40 3.00 5.33 7.00 2.62 3.53 5.70 8.40
Lead-in Chamfer* Diameter increase DN min. 1.1 1.4 1.9 2.7 3.5
* Though not less than 1.5 % of service diameter (bore/rod diameter). **The O-Ring cross section d2 can be found in the in the appropriate table Installation Dimensions, from chapter Double DeltaR.
* The groove width can be found in table Installation dimensions for TurconR Glyd RingR T, TurconR AQ-SealR5, TurconR StepsealR K, ZurconR Wynseal and TurconR AQ-SealR.
Busak+ Shamban
8
Piston Seals
Surface Roughness DIN EN ISO 4287 The functional reliability and service life of a seal depend to a very great extent on the quality and surface finish of the mating surface to be sealed. Scores, scratches, pores, concentric or spiral machining marks are not permitted. Higher demands must be made on the surface finish of dynamic surfaces than of static mating surfaces. The characteristics most frequently used to describe the surface microfinish Ra, Rz and Rmax are defined in DIN EN ISO 4287. These characterics alone, however, are not sufficient for assessing the suitability in seal technology. In addition the material contact area of the surface roughness profile Rmr in accordance with DIN EN ISO 4287 should be demanded. The significance of this surface specification is illustrated in Fig. 2. It shows clearly that specification of Ra and Rz alone does not describe the surface roughness profile accurately enough for the seal technology and is thus not sufficient for assessing the suitability. The material contact area Rmr is essential for assessing surfaces, as this parameter is determined by the specific surface roughness profile. This in turn is directly dependent on the machining process employed. Busak+Shamban recommends that the following surface finishes be observed: Table V Surface Roughness
Surface Roughness m Mating Surface Parameter Rmax Rz DIN Ra TurconR Materials 0.63 - 2.50 0.40 - 1.60 0.05 - 0.20 ZurconR and Rubber 1.00 - 4.00 0.63 - 2.50 0.10 - 0.40 Groove G Surface < 16.0 < 10.0 < 1.6
Ra
Rz
Rmr
0.1
1.0
70%
Figure 2 Profile forms of surfaces Figure 2 shows two surface profiles, both of which exhibit nearly the same value for Rz in the test procedure. The difference becomes obvious only when the material contact area of the surface roughness profiles are compared. These show that the upper roughness profile with Rmr = 70% has the better seal/mating surface ratio.
The material contact area Rmr should be approx. 50 to 70%, determined at a cut depth c = 0.25 x Rz, relative to a reference line of Cref. 5%.
Busak+ Shamban
9
Piston Seals
Figure 3 Installation in a split groove Installation in Closed Grooves - Without installation aids Observing the instructions in the chapter General installation instructions, installation of Compact Seal and Wynseal seal elements in closed grooves is relatively simple. Figure 5 Sizing of the installed seal
Busak+ Shamban
10
Piston Seals
Installation in Closed Grooves - With installation aids Use of a three-piece installation tool is recommended for the series production installation of TurconR and ZurconR seal elements. The tool consists of: - Installation sleeve - Expanding sleeve - Sizing sleeve All these parts should be made of a polymer material (e.g. PA6) with good sliding characteristics and low abrasiveness to avoid damage to the seals.
In view of the wide range of sizes and the applicationspecific installation conditions, these installation tools cannot be supplied as standard by Busak+Shamban. On request, however, we will gladly provide specimen drawings to allow you to manufacture these tools. The sequence of installation is illustrated in Fig. 6 to 8. Note, however, that the installation of TurconR seal elements should be performed quickly in order to ensure optimum recovery of the seal ring.
Figure 6 Expanding the TurconR or ZurconR sealing element using an expanding sleeve over the installation sleeve
Busak+ Shamban
11
Piston Seals
Installation of TurconR Double DeltaR Installation in closed grooves is possible from 8 mm bore diameter. For diameters smaller than 50 mm a loading mandrel (Fig. 9) is recommended. After installation the seal must be calibrated, this may be done with the lead-in chamfer of the cylinder tube or by means of a separate calibration sleeve. - TurconR piston seals can be installed more easily by heating to approx. 80_C to 100_C (expanding and then shrinking back to the original form).
Busak+ Shamban
12
Piston Seals
Installation of Spring Energized Seals TurconR seals should preferably be installed in split grooves. Installation in half-open grooves is possible with a snap fitting. Figure 10 shows the design of the groove. Polished 15d-20d y VarisealR
30_
In exceptional cases or with existing designs, an installation in closed grooves is also possible. The details in Table VII should be regarded as guide values for installation. Table VII Installation in closed grooves
DN
Installation of the Compact Seal The Compact Seal can be installed in one-piece or split pistons. On one-piece pistons, the inner rubber- elastic sealing element is first installed in the middle of the groove diameter by expanding over the piston. Then the cut Back-up Ring are fitted on both sides of the sealing element and then the two cut guide rings are installed. On split pistons the individual parts are installed in the following order: Guide ring, Back-up Ring, sealing element, Back-up Ring, Guide ring. Before installation all seal parts, including piston and cylinder, should be oiled or greased.
Busak+ Shamban
13
Piston Seals
Busak+ Shamban
14
- Double Acting - Rubber Energised Plastic Faced Seal - Material - TurconR, ZurconR and Elastomer -
Busak+ Shamban
15
Busak+ Shamban
16
Figure 12
Busak+ Shamban
17
Technical Data Operating conditions: The TurconR Glyd RingR is recommended for reciprocating (with a length of stroke at least twice the groove width) and helical movements. Pressure: Speed: Frequency: Temperature: Media: up to 80MPa up to 15m/s up to 5 Hz. -45C to +200C *) (depending on O-Ring Material) Mineral oil based hydraulic fluids, barely flammable hydraulic fluids, environmentally safe hydraulic fluids (biological degradable oils), water, air and others. Depending on the O-Ring material compatibility. the maximum permissible radial clearance Smax is shown in the table IX, as a function of the operating pressure and functional diameter.
Special Application: H Short stroke movements, non-lubricating fluids or pneumatic applications require self-lubricating sealing materials. Therefore we recommend: TurconR Seal: Energiser: TurconR T29 O-Ring NBR 70 Shore A or FKM 70 Shore A depending on the temperature T29N or T29V
Set reference:
H If low friction coefficient is required, we recommend: TurconR Seal: Energiser: TurconR T 05 O-Ring NBR 70 Shore A or FKM 70 Shore A depending on the temperature. For special requirements other elastomers are available on request T05N or T05V
Clearance:
Set reference:
If rougher surface finish must be sealed, we recommend: ZurconR Seal: Energiser: Set reference: ZurconR Z51 O-Ring NBR 70 Shore A Z51N
Important Note: The above data are maximum values and cannot be used at the same time. e.g. the maximum operating speed depends on material type, pressure, temperature and gap value. Temperature range also dependent on medium. *) In the case of unpressurized applications in temperatures below 0C please contact our application engineers for assistance ! Materials Standard Application: H For hydraulic components in mineral oils containing zinc or medium with good lubricating performance. TurconR seal: Energiser: TurconR T 46 O-Ring NBR 70 shore A or FKM 70 Shore A depending on the temperature T46N or T46V
Set reference.
Busak+ Shamban
18
T46
N T
-10 to +200 -30 to +100 -45 to +80 -10 to +200 -30 to +100 -45 to +80 -10 to +200 -45 to +145 -30 to +100 -45 to +80 -10 to +200 -45 to +145 -30 to +100 -45 to +80 -10 to +200 -30 to +100 -45 to +80 -10 to +200 -30 to +100 -45 to +80 -10 to +200 -45 to +145 -30 to +100 -45 to +80 Steel Steel, hardened Cast i C t iron Ceramic coating Stainless steel 80 Steel Stainless steel St i l t l 60 Steel tubes Steel, Steel hardened Cast iron 30 Steel tubes Steel, hardened S l h d d 20 0 Steel Cast iron Stainless steel Aluminium Bronze B 60 Steel Cast iron Stainless steel Aluminium Bronze B Alloys 25 S ee ubes Steel tubes Steel, hardened S l h d d Cast iron 80
ZurconR Z80 Z80 NBR - 70 Shore A N -30 to +80 Steel 40 Stainless steel For lubricating and non-lubricating hydraulic Aluminium fluids, high abrasion resistance, very good Bronze chemical resistance, limited temperature NBR - Low temp. T -45 to +80 Ceramic coating resistance. 70 Shore A Ultra high molecular weight polyethylen Colour: White to off-white * The O-Ring Operation Temperature is only valid in mineral hydraulic oil. BAM: Tested by Bundes Anstalt Materialprfung, Germany. Highlighted materials are standard. **Material not suitable for mineral oils. *** max. 2300 mm
Busak+ Shamban
19
Installation Recommendations
8 - 14.9 15 - 39.9 40 - 79.9 80 - 132.9 133 - 329.9 330 - 669.9 670 - 999.9
15 - 39.9 40 - 79.9 80 - 132.9 133 - 329.9 330 - 669.9 670 - 999.9 > 1000
* At pressures > 40 MPa use diameter tolerance H8/f8 (bore/piston) in area of the seal.
Ordering Example TurconR Glyd RingR, complete with O-Ring, standard application, Series PG44 (from Table IX ). Bore diameter: DN = 80.0 mm Part No.: PG4400800 (from Table X) Select the material from Table VIII. The corresponding code numbers are appended to the Part No. Preferred Series (Table X). Together they form the order number. The order number for all intermediate sizes not shown in Preferred Series (Table X) can be determined following the example opposite. ** For diameters 1000.0 mm multiply only by factor 1. Example: PG44 for diameter 1200.0 mm. Order no.: PG44X1200 - T46N.
PG44 0 0800 -
T46
Type (Standard) Bore diameter x 10** Quality Index (Standard) Material code (Seal ring) Material code (O-Ring)
Busak+ Shamban
20
Table X
Bore Dia. DN H9 8.0 10.0 12.0 14.0 15.0 16.0 16.0 18.0 18.0 19.05 20.0 20.0 21.0 22.0 22.0 24.0 25.0 25.0 25.0 25.4 28.0 30.0 32.0 32.0 32.0 35.0 35.0 36.0 38.0 40.0 40.0 42.0 44.45 45.0 48.0 50.0 50.0 50.0 50.8 50.8 52.0 53.0
Busak+ Shamban
21
Bore Dia. DN H9 127.0 130.0 130.0 132.0 135.0 140.0 140.0 145.0 145.0 150.0 150.0 155.0 160.0 160.0 165.0 170.0 175.0 180.0 180.0 190.0 194.0 200.0 200.0 205.0 210.0 215.0 220.0 230.0 230.0 240.0 250.0 250.0 250.0 254.0 260.0 265.0 268.0 270.0 280.0 290.0 300.0 300.0
Groove Dia. d1 h9 111.5 114.5 109.0 121.0 114.0 124.5 119.0 129.5 124.0 134.5 129.0 134.0 144.5 139.0 144.0 149.0 154.0 164.5 159.0 169.0 178.5 184.5 179.0 184.0 189.0 194.0 199.0 214.5 209.0 219.0 134.5 229.0 225.5 233.0 239.0 244.0 247.0 249.0 259.0 269.0 279.0 275.5
Groove Width L1 +0.2 6.3 6.3 8.1 4.2 8.1 6.3 8.1 6.3 8.1 6.3 8.1 8.1 6.3 8.1 8.1 8.1 8.1 6.3 8.1 8.1 6.3 6.3 8.1 8.1 8.1 8.1 8.1 6.3 8.1 8.1 6.3 8.1 8.1 8.1 8.1 8.1 8.1 8.1 8.1 8.1 8.1 8.1
Part No.
O-Ring Dimensions 110.49 x 5.33 113.67 x 5.33 108 x 7.0 120.24 x 3.53 113.67 x 7.0 123.19 x 5.33 116.84 x 7.0 126.37 x 5.33 123.19 x 7.0 132.72 x 5.33 126.37 x 7.0 132.72 x 7.0 142.24 x 5.33 135.89 x 7.0 142.24 x 7.0 145.42 x 7.0 151.77 x 7.0 164.47 x 5.33 158.12 x 7.0 164.47 x 7.0 177.17 x 5.33 183.52 x 5.33 177.17 x 7.0 183.52 x 7.0 183.52 x 7.0 189.87 x 7.0 196.22 x 7.0 208.92 x 5.33 208.92 x 7.0 215.27 x 7.0 234.32 x 5.33 227.97 x 7.0 215.27 x 7.0 227.97 x 7.0 240.67 x 7.0 240.67 x 7.0 240.67 x 7.0 240.67 x 7.0 253.37 x 7.0 266.07 x 7.0 278.77 x 7.0 266.07 x 7.0
Bore Dia. DN H9 304.8 310.0 320.0 320.0 330.0 340.0 350.0 360.0 370.0 380.0 400.0 420.0 430.0 440.0 450.0 460.0 480.0 500.0 555.0 600.0 640.0 660.0 700.0 710.0 740.0 780.0 800.0 900.0 1000.0 1000.0 1050.0 1065.0 1070.0 1200.0 1200.0 1225.0 1500.0 2000.0 2700.0
Groove Dia. d1 h9 283.8 289.0 299.0 295.5 305.5 315.5 325.5 335.5 345.5 355.5 375.5 395.5 405.5 415.5 425.5 435.5 455.5 475.5 530.5 575.5 615.5 635.5 672.0 682.0 712.0 752.0 772.0 872.0 972.0 962.0 1022.0 1027.0 1032.0 1172.0 1162.0 1187.0 1462.0 1962.0 2662.0
Groove Width L1 +0.2 8.1 8.1 8.1 8.1 8.1 8.1 8.1 8.1 8.1 8.1 8.1 8.1 8.1 8.1 8.1 8.1 8.1 8.1 8.1 8.1 8.1 8.1 9.5 9.5 9.5 9.5 9.5 9.5 9.5 13.8 9.5 13.8 13.8 9.5 13.8 13.8 13.8 13.8 13.8
Part No.
O-Ring Dimensions 278.77 x 7.0 278.77 x 7.0 291.47 x 7.0 291.47 x 7.0 304.17 x 7.0 316.87 x 7.0 316.87 x 7.0 329.57 x 7.0 342.27 x 7.0 354.97 x 7.0 367.67 x 7.0 393.07 x 7.0 405.26 x 7.0 405.26 x 7.0 417.96 x 7.0 430.66 x 7.0 456.06 x 7.0 468.76 x 7.0 506.86 x 7.0 557.66 x 7.0 608.08 x 7.0 633.48 x 7.0 670 x 8.4 680 x 8.4 710 x 8.4 750 x 8.4 770 x 8.4 870 x 8.4 970 x 8.4 960 x 12.0 1020 x 8.4 1025 x 12.0 1030 x 12.0 1170 x 8.4 1160 x 12.0 1185 x 12.0 1460 x 12.0 1960 x 12.0 2660 x 12.0
PG4401270 PG4401300 PG4201300 PG4601320 PG4401350 PG4601400 PG4401400 PG4601450 PG4401450 PG4601500 PG4401500 PG4401550 PG4601600 PG4401600 PG4401650 PG4401700 PG4401750 PG4601800 PG4401800 PG4401900 PG4601940 PG4602000 PG4402000 PG4402050 PG4402100 PG4402150 PG4402200 PG4602300 PG4402300 PG4402400 PG4602500 PG4402500 PG4202500 PG4402540 PG4402600 PG4402650 PG4402680 PG4402700 PG4402800 PG4402900 PG4403000 PG4203000
PG4403048 PG4403100 PG4403200 PG4203200 PG4403300 PG4403400 PG4403500 PG4403600 PG4403700 PG4403800 PG4404000 PG4404200 PG4404300 PG4404400 PG4404500 PG4404600 PG4404800 PG4405000 PG4405550 PG4406000 PG4406400 PG4406600 PG4407000 PG4407100 PG4407400 PG4407800 PG4408000 PG4409000 PG46X1000 PG44X1000 PG46X1050 PG44X1065 PG44X1070 PG46X1200 PG44X1200 PG44X1225 PG44X1500 PG44X2000 PG44X2700
All dimensions in bold type are suitable for installation in grooves to ISO 7425/1, bore dia. in accordance with ISO 3320.Other dimensions and all intermediate sizes up to 2700 mm dia. including inch sizes can be supplied. All O-Rings with 12 mm cross section are delivered as special Profilring.
Busak+ Shamban
22
- Double Acting - Rubber Energised Plastic Faced Seal - Material - TurconR, ZurconR and Elastomer -
Busak+ Shamban
23
Busak+ Shamban
24
TurconRGlyd RingR T *
Description TurconR Glyd RingR T is a further technical development of the TurconR Glyd RingR seal which has been successfully used for decades. It is fully interchangeable with the earlier Glyd RingR seals in all new applications. Glyd RingR T meets all the market demands for a function-specific seal solution, observing economic and ecological aspects. The benefits of the patented seal concept are provided by the innovative functional principle of the trapezoidal profile cross-section. Both lateral profile flanks are inclined so that the seal profile tapers towards the seal surface. The profile can thus retain the robust and compact form typical of piston seals without losing any of the flexibility required to achieve a pressure-related maximum compression (Figure 14). Advantages The benefits offered to date by the Glyd RingR are still retained in full, and are now complemented by a number of further important advantages: - Very good static leak-tightness - Increased clearance possible (approx. +50%), depending on the operating conditions - Due to the larger extrusion gap, safe use even with soiled media - Low friction, no stick-slip effect - Simple groove design, one-piece pistons possible - Installation grooves to ISO 7425/1 - Adaptable to the operating conditions due to a wide range of possible materials (TurconR, ZurconR) - Suitable for new environmentally safe hydraulic fluids p
Turconr Seal ring O-Ring
- Available for all cylinder diameters up to 2.700 mm. Application Examples The TurconR Glyd RingR T is the recommended sealing element for double acting pistons of hydraulic components such as: S Injection moulding machines S Machine tools S Presses S Excavators S Forklifts & handling machinery S Agriculture S Valves for hydraulic & pneumatic circuits. It is particularly recommended for heavy duty and large diameter applications.
Figure 14 TurconRGlyd RingR T The edge angle created by the special Glyd RingR T crosssectional form permits an additional degree of freedom and enables a slight tilting movement of the seal. The maximum compression is thus always shifted towards the area of the seal edge directly exposed to the pressure. On the low-pressure edge of the seal, on the other hand, the Glyd RingR T exhibits only zones with neutral strains without compressive or shearing loads, thus effectively reducing the danger of gap extrusion. The resulting benefits for the user can be seen in the following list.
Busak+ Shamban
25
Technical Data Operating conditions pressure: Up to 80 MPa Speed: Temperature: Media: Up to 15 m/s -45C to +200C *) (depending on O-Ring material). Mineral oil-based hydraulic fluids, barely flammable hydraulic fluids, environmentally safe hydraulic fluids (bio-oils), water, air and others, depending on the O-Ring material The maximum permissible radial clearance smax is shown in Table XII, as a function of the operating pressure and functional diameter.
Materials Standard Application: H For hydraulic components with reciprocating movement in mineral oils containing zinc or medium with good lubricating performance. TurconR Seal: Energiser: Set reference: TurconR T46 O-Ring NBR 70 shore A or FKM 70 Shore A depending on the temperature T46N or T46V
Clearance:
Special Application: H Non-lubricating fluids or pneumatic applications require self-lubricating sealing materials. Therefore we recommend: TurconR Seal: Energiser: TurconR T40 O-Ring NBR 70 Shore A or FKM 70 Shore A depending on the temperature T40N or T40V
Important Note: The above data are maximum values and cannot be used at the same time. e.g. the maximum operating speed depends on material type, pressure, temperature and gap value. Temperature range also dependent on medium. *) In the case of unpressurized applications in temperatures below 0C please contact our application engineers for assistance !
Set reference:
H If rougher surface finish must be sealed, we recommend: ZurconR Seal: Energiser: Set reference: ZurconR Z51 O-Ring NBR 70 Shore A Z51N
Mating Surface Material Steel tubes Steel, hardened Cast iron MPa max. 60
T46
N T
V N T V E** N T
-10 to +200 -30 to +100 -45 to +80 -10 to +200 -45 to +145 -30 to +100 -45 to +80 Steel Steel, hardened Cast i C t iron Ceramic coating Stainless steel 80 Steel Cast iron Stainless steel Aluminium Bronze B 25
T40
NBR - 70 Shore A NBR - Low temp. 70 Shore A FKM - 70 Shore A EPDM - 70 Shore A
Z51
* The O-Ring Operation Temperature is only valid in mineral hydraulic oil. BAM: Tested by Bundes Anstalt Materialprfung, Germany. Highlighted materials are standard. **Material not suitable for mineral oils. *** max. 2300 mm
Busak+ Shamban
26
Installation Recommendation
8 - 14.9 15 - 39.9 40 - 79.9 80 - 132.9 133 - 329.9 330 - 669.9 670 - 999.9
15 - 39.9 40 - 79.9 80 - 132.9 133 - 329.9 330 - 669.9 670 - 999.9 - 1000
* At pressures > 40 MPa use diameter tolerance H8/f8 (bore/piston) in area of the seal.
Ordering example TurconR Glyd RingR T, complete with O-Ring, standard application, series PT03 (from Table XII). Bore diameter: DN = 80.0 mm Part No.: PT0300800 (from Table XIII) Select the material from Table XI. The corresponding code numbers are appended to the Part No. (from Table XIII). Together they form the Order No. For all intermediate sizes not shown in Table XIII, the Order No. can be determined from the example opposite. *** For diameters 1000.0 mm multiply only by factor 1. Example: PT06 for diameter 1200.0 mm. Order no.: PT06X1200 - T46N.
PT03
0 0800 -
T46
Type (Standard) Cylinder diameter x 10*** Quality Index (Standard) Material code (Seal ring) Material code (O-Ring)
Busak+ Shamban
27
Table XIII
Bore Dia. DN H9 8.0 10.0 12.0 14.0 15.0 16.0 16.0 18.0 18.0 19.05 20.0 20.0 21.0 22.0 22.0 24.0 25.0 25.0 25.0 25.4 28.0 30.0 32.0 32.0 32.0 35.0 35.0 36.0 38.0 40.0 40.0 42.0 44.45 45.0 48.0 50.0 50.0 50.0 50.8 50.8 52.0 53.0
Groove Dia. d1 h9 3.1 5.1 7.1 9.1 7.5 11.1 8.5 13.1 10.5 11.55 15.1 12.5 13.5 17.1 14.5 16.5 20.1 17.5 14.0 20.5 20.5 22.5 27.1 24.5 21.0 27.5 24.0 28.5 30.5 32.5 29.0 31.0 36.95 34.0 37.0 42.5 39.0 34.5 43.3 39.8 41.0 42.0
Busak+ Shamban
28
Bore Dia. DN H9 127.0 130.0 130.0 132.0 135.0 140.0 140.0 145.0 145.0 150.0 150.0 155.0 160.0 160.0 165.0 170.0 175.0 180.0 180.0 190.0 194.0 200.0 200.0 205.0 210.0 215.0 220.0 230.0 230.0 240.0 250.0 250.0 250.0 254.0 260.0 265.0 268.0 270.0 280.0 290.0 300.0 300.0
Groove Dia. d1 h9 111.5 114.5 109.0 121.0 114.0 124.5 119.0 129.5 124.0 134.5 129.0 134.0 144.5 139.0 144.0 149.0 154.0 164.5 159.0 169.0 178.5 184.5 179.0 184.0 189.0 194.0 199.0 214.5 209.0 219.0 134.5 229.0 225.5 233.0 239.0 244.0 247.0 249.0 259.0 269.0 279.0 275.5
Groove Width L1 +0.2 6.3 6.3 8.1 4.2 8.1 6.3 8.1 6.3 8.1 6.3 8.1 8.1 6.3 8.1 8.1 8.1 8.1 6.3 8.1 8.1 6.3 6.3 8.1 8.1 8.1 8.1 8.1 6.3 8.1 8.1 6.3 8.1 8.1 8.1 8.1 8.1 8.1 8.1 8.1 8.1 8.1 8.1
Part No.
O-Ring Dimensions 110.49 x 5.33 113.67 x 5.33 108 x 7.0 120.24 x 3.53 113.67 x 7.0 123.19 x 5.33 116.84 x 7.0 126.37 x 5.33 123.19 x 7.0 132.72 x 5.33 126.37 x 7.0 132.72 x 7.0 142.24 x 5.33 135.89 x 7.0 142.24 x 7.0 145.42 x 7.0 151.77 x 7.0 164.47 x 5.33 158.12 x 7.0 164.47 x 7.0 177.17 x 5.33 183.52 x 5.33 177.17 x 7.0 183.52 x 7.0 183.52 x 7.0 189.87 x 7.0 196.22 x 7.0 208.92 x 5.33 208.92 x 7.0 215.27 x 7.0 234.32 x 5.33 227.97 x 7.0 215.27 x 7.0 227.97 x 7.0 240.67 x 7.0 240.67 x 7.0 240.67 x 7.0 240.67 x 7.0 253.37 x 7.0 266.07 x 7.0 278.77 x 7.0 266.07 x 7.0
Bore Dia. DN H9 304.8 310.0 320.0 320.0 330.0 340.0 350.0 360.0 370.0 380.0 400.0 420.0 430.0 440.0 450.0 460.0 480.0 500.0 555.0 600.0 640.0 660.0 700.0 710.0 740.0 780.0 800.0 900.0 1000.0 1000.0 1050.0 1065.0 1070.0 1200.0 1200.0 1225.0 1500.0 2000.0 2700.0
Groove Dia. d1 h9 283.8 289.0 299.0 295.5 305.5 315.5 325.5 335.5 345.5 355.5 375.5 395.5 405.5 415.5 425.5 435.5 455.5 475.5 530.5 575.5 615.5 635.5 672.0 682.0 712.0 752.0 772.0 872.0 972.0 962.0 1022.0 1027.0 1032.0 1172.0 1162.0 1187.0 1462.0 1962.0 2662.0
Groove Width L1 +0.2 8.1 8.1 8.1 8.1 8.1 8.1 8.1 8.1 8.1 8.1 8.1 8.1 8.1 8.1 8.1 8.1 8.1 8.1 8.1 8.1 8.1 8.1 9.5 9.5 9.5 9.5 9.5 9.5 9.5 13.8 9.5 13.8 13.8 9.5 13.8 13.8 13.8 13.8 13.8
Part No.
O-Ring Dimensions 278.77 x 7.0 278.77 x 7.0 291.47 x 7.0 291.47 x 7.0 304.17 x 7.0 316.87 x 7.0 316.87 x 7.0 329.57 x 7.0 342.27 x 7.0 354.97 x 7.0 367.67 x 7.0 393.07 x 7.0 405.26 x 7.0 405.26 x 7.0 417.96 x 7.0 430.66 x 7.0 456.06 x 7.0 468.76 x 7.0 506.86 x 7.0 557.66 x 7.0 608.08 x 7.0 633.48 x 7.0 670 x 8.4 680 x 8.4 710 x 8.4 750 x 8.4 770 x 8.4 870 x 8.4 970 x 8.4 960 x 12.0 1020 x 8.4 1025 x 12.0 1030 x 12.0 1170 x 8.4 1160 x 12.0 1185 x 12.0 1460 x 12.0 1960 x 12.0 2660 x 12.0
PT0301270 PT0301300 PT0401300 PT0201320 PT0401350 PT0301400 PT0401400 PT0301450 PT0401450 PT0301500 PT0401500 PT0401550 PT0301600 PT0401600 PT0401650 PT0401700 PT0401750 PT0301800 PT0401800 PT0401900 PT0301940 PT0302000 PT0402000 PT0402050 PT0402100 PT0402150 PT0402200 PT0302300 PT0402300 PT0402400 PT0302500 PT0402500 PT0802500 PT0402540 PT0402600 PT0402650 PT0402680 PT0402700 PT0402800 PT0402900 PT0403000 PT0803000
PT0403048 PT0403100 PT0403200 PT0803200 PT0803300 PT0803400 PT0803500 PT0803600 PT0803700 PT0803800 PT0804000 PT0804200 PT0804300 PT0804400 PT0804500 PT0804600 PT0804800 PT0805000 PT0805550 PT0806000 PT0806400 PT0806600 PT0507000 PT0507100 PT0507400 PT0507800 PT0508000 PT0509000 PT05X1000 PT06X1000 PT05X1050 PT06X1065 PT06X1070 PT05X1200 PT06X1200 PT06X1225 PT06X1500 PT06X2000 PT06X2700
All dimensions in bold type are suitable for installation in grooves to ISO 7425/1, bore dia. in accordance with ISO 3320.Other dimensions and all intermediate sizes up to 2700 mm dia. including inch sizes can be supplied. All O-Rings with 12 mm cross section are delivered as special profilring.
Busak+ Shamban
29
Busak+ Shamban
30
R AQ-SEALR 5 TURCON
- Double Acting - Rubber Energised Plastic Faced Seal - Material - TurconR and Elastomer -
Busak+ Shamban
31
Busak+ Shamban
32
TurconR AQ-SealR 5
TurconR AQ-SealR 5*
Description The TurconR AQ-SealR 5 is a patented development of the proven standard TurconR AQ-SealR. The seal profile of the TurconR ring has been redesigned on both the dynamic and static sealing surface. Two O-Rings are used to energize the seal instead of one. Application Examples The TurconR AQ-SealR 5 is the recommended sealing element for double acting pistons of accumulators and positioning and holding cylinders for: S Machine tools S Presses S Rolling mills S Off shore S Accumulators S Heavy duty suspension cylinders It is particularly recommended for heavy duty and large diameter applications. Technical Data Operating conditions pressure: Figure 16 TurconR AQ-SealR 5 The AQ-SealR 5 combines the benefits of a low-friction TurconR slipper seal with the high sealing characteristics of an elastomeric seal by incorporating a limited foot print QUAD-RINGR Seal in the dynamic sealing face. This optimizes leakage control while minimizing friction. The particular characteristics of the AQ-SealR 5 are the special seal profile with a defined seal edge and the use of two O-Rings as energizing elements to optimize the pressure profile and to reduce the force of attack at gas permeability. Speed: Temperature: 60 MPa Up to 3 m/s -30C to +200C *) (depending on O-Ring and QUAD-RINGR Seal material) (For applications at low temperatures below -30C, please contact us). For all common hydraulic fluids, including bio-oils and gases The maximum permissible radial clearance Smax is shown in Table XV, as a function of the operating pressure and functional diameter.
Media: Clearance:
* Patent-No. EP 0 424 372 Advantages - High sealing effect in applications requiring media separation, e.g. fluid/fluid or fluid/gas - Double security through the combination of low-friction special materials with elastomer seals - Low gas permeation rate - Higher pressure application, higher sliding speed compared to the AQ-SealR - Outstanding sliding properties, no stick-slip effect.
Important Note: The above data are maximum values and cannot be used at the same time. e.g. the maximum operating speed depends on material type, pressure, temperature and gap value. Temperature range also dependent on medium. *) In the case of unpressurized applications in temperatures below 0C please contact our application engineers for assistance !
Busak+ Shamban
33
TurconR AQ-SealR 5
Materials Standard Application: H For hydraulic components in mineral oils or medium with good lubricating performance. H Mineral oils and gases TurconR Seal: Energiser: TurconR T46 O-Ring and QUAD-RING Seal in NBR 70 Shore A (code N)
Code O-Ring Material NBR - 70 Shore A Code O-Ring Operating Temp.* C -30 to +100 Mating Surface Material Steel tubes Steel, hardened Cast iron MPa max. 60
Special Application: H For special applications requiring other material combinations, please contact your local Busak+Shamban Company.
T46
FKM - 70 Shore A
-10 to +200
T40
N V E**
25
Turcon T10 T10 NBR - 70 Shore A N -30 to +100 60 Steel For oil hydraulic and pneumatic for Stainless steel all lubricating and non-lubricating FKM - 70 Shore A V -20 to +200 fluids, high extrusion resistance, good chemical resistance BAM tested resistance, tested. EPDM-70 Shore A E** -45 to +145 Carbon, graphite filled Colour: Black * The O-Ring Operation Temperature is only valid in mineral hydraulic oil. BAM: Tested by Bundes Anstalt Materialprfung, Germany. Highlighted materials are standard. **Material not suitable for mineral oils.
Busak+ Shamban
34
TurconR AQ-SealR 5
Installation Recommendation
d2
*At pressures > 30 MPa use diameter tolerance H8/f8 (bore/piston) in area of the seal.
Ordering example TurconRAQ-SealR5, complete with O-Ring and QUAD-RINGR Seal, recommended range, Series PQ02 (from Table XV). Bore diameter: DN = 80.0 mm Part No. PQ0200800 (from Table XVI) Select the material from Table XIV. The corresponding code numbers are appended to the Part No. (from Table XVI). Together they form the Order No. For all intermediate sizes not shown in Table XVI, the Order No. can be determined from the example opposite.
PQ02 0 0800 -
T46
Type (Standard) Cylinder diameter x 10 Quality Index (Standard) Material code (Seal ring) Material code (O-Ring)/(QUAD-RINGR Seal)
Busak+ Shamban
35
TurconR AQ-SealR 5
Table XVI
Bore Diameter DN H9 40.0 42.0 45.0 48.0 50.0 52.0 55.0 60.0 63.0 65.0 70.0 75.0 80.0 85.0 90.0 95.0 100.0 105.0 110.0 115.0 120.0 125.0 130.0 135.0 140.0 150.0 160.0 170.0 180.0 190.0 200.0 210.0 220.0 230.0 240.0 250.0 280.0 300.0 320.0
Bore diameters in bold type comply with the recommendations of ISO 3320.
All intermediate sizes up to 700 mm diameter can be supplied. Sizes > 700 mm diameter with special elastomers on request.
Busak+ Shamban
36
TurconR AQ-SealR 5
Bore Diameter DN H9 350.0 400.0 420.0 450.0 480.0 500.0 600.0 700.0
Groove Diameter d1 h9 332.0 382.0 402.0 432.0 449.0 469.0 569.0 669.0
Groove Width L1 +0.2 12.3 12.3 12.3 12.3 16.3 16.3 16.3 16.3
Part No.
O-Ring Dimensions 329.57 x 5.33 380.37 x 5.33 405.26 x 5.33 430.66 x 5.33 443.36 x 7.0 468.76 x 7.0 557.66 x 7.0 658.88 x 7.0
QUAD-RING Dimensions 329.79 x 3.53 380.59 x 3.53 380.59 x 3.53 430.66 x 3.53 456.06 x 5.33 456.06 x 5.33 557.58 x 5.33 658.88 x 5.33
Bore diameters in bold type comply with the recommendations of ISO 3320.
All intermediate sizes up to 700 mm diameter can be supplied. Sizes > 700 mm diameter with special elastomers on request.
Busak+ Shamban
37
TurconR AQ-SealR 5
Busak+ Shamban
38
R AQ-SEALR TURCON
- Double Acting - Rubber Energised Plastic Faced Seal - Material - TurconR and Elastomer -
Busak+ Shamban
39
Busak+ Shamban
40
TurconR AQ-SealR
TurconRAQ-SealR
Description The TurconR AQ-SealR is a double-acting seal consisting of a seal ring of high-grade modified TurconR material, a QUAD-RINGR Seal and an O-Ring as energizing element. The TurconR seal ring and the QUAD-RINGR Seal together assume the dynamic sealing function whilst the O-Ring performs the static sealing function. Design The AQ-SealR is supplied as standard with radial notches on both sides. These ensure direct pressurizing of the seal under all operating conditions. QUAD-RINGR Seal ring TurconR Seal Application Examples The TurconR AQ-SealR is the recommended sealing element for double acting pistons of accumulators and positioning and holding cylinders for: S S S S S Machine tools Presses Accumulators Stabilisers Heavy duty suspension cylinders
Technical Data Operating pressure: Speed: Temperature: 40 MPa Up to 2 m/s -45C to +200C *) (depending on O-Ring and QUAD-RINGR Seal material) (For applications at low temperatures below -30C, please contact us). For all common hydraulic fluids, including bio-oils and gases The maximum permissible radial clearance Smax is shown in Table XVIII, as a function of the operating pressure and functional diameter.
Notches
Important Note: The above data are maximum values and cannot be used at the same time. e.g. the maximum operating speed depends on material type, pressure, temperature and gap value. Temperature range also dependent on medium. *) In the case of unpressurized applications in temperatures below 0C please contact our application engineers for assistance !
Figure 18 TurconRAQ-SealR Advantages - High sealing effect in applications requiring media separation, e.g. fluid/fluid or fluid/gas - Double security through the combination of low-friction special materials with elastomer seals - Simple groove design, small installation space, interchangeable with TurconR Glyd RingR, TurconR Glyd RingR T and TurconR StepsealRK installation according to ISO 7425/1 - Outstanding sliding properties, no stick-slip effect.
Busak+ Shamban
41
TurconR AQ-SealR
Materials Standard Application: H For hydraulic components in mineral oils or medium with good lubricating performance. H Mineral oils and gases TurconR Seal: Energiser: Table XVII
Material, Applications, Properties Turcon T46 Standard material for hydraulics, high compressive strength, good sliding and wear properties, good extrusion resistance, BAM tested. Bronze filled Colour: Greyish to dark brown Turcon T40 For all lubricating and non-lubricating hydraulic fluids, hydraulic oils without zinc, a e yd au c, soft a g surfaces. water hydraulic, so mating su aces. Carbon fibre filled b f b f ll d Colour: Grey
Special Application: H For special applications requiring other material combinations, please contact your local Busak+Shamban Company.
TurconR T46 O-Ring and QUAD-RINGR Seal in NBR 70 Shore A (code N) Turcon Materials for Turcon AQ-Seal
Code O-Ring Material NBR - 70 Shore A NBR - Low temp. 70 Shore A FKM - 70 Shore A T40 NBR - 70 Shore A NBR - Low temp. 70 Shore A FKM - 70 Shore A EPDM-70 Shore A Code O-Ring Operating Temp.* C -30 to +100 -45 to +80 Mating Surface Material Steel tubes Steel, hardened Cast iron MPa max. 40
T46
N T
V N T V E** N T V E**
-10 to +200 -30 to +100 -45 to +80 -10 to +200 -45 to +145 -30 to +100 -45 to +80 -10 to +200 -45 to +145 Steel Stainless steel St i l t l 40 Steel Cast iron Stainless steel, Aluminium Bronze B Alloys 25
Turcon T10 For il hydraulic and pneumatic f F oil h d li d ti for all lubricating and non-lubricating fluids, high extrusion resistance, good chemical resistance, BAM tested. Carbon, Carbon graphite filled Colour: Black
T10
NBR - 70 Shore A NBR - Low temp. 70 Shore A FKM - 70 Shore A EPDM-70 Shore A
* The O-Ring Operation Temperature is only valid in mineral hydraulic oil. BAM: Tested by Bundes Anstalt Materialprfung, Germany. Highlighted materials are standard. **Material not suitable for mineral oils.
Busak+ Shamban
42
TurconR AQ-SealR
Installation Recommendation
Ordering example TurconR AQ-SealR, complete with O-Ring and QUAD-RINGR Seal, recommended range, Series PQ22 (from Table XVIII). Bore diameter: DN = 80.0 mm Part No. PQ2200800 (from Table XIX) Select the material from Table XVII. The corresponding code numbers are appended to the Part No. (from Table XIX). Together they form the Order No. For all intermediate sizes not shown in Table XIX, the Order No. can be determined from the example opposite.
PQ22 0 0800 -
T46
Type (Standard) Cylinder diameter x 10 Quality Index (Standard) Material code (Seal ring) Material code (O-Ring)/(QUAD-RINGR Seal)
Busak+ Shamban
43
TurconR AQ-SealR
The dimensions in bold type are suitable for grooves to ISO 7425/1. bore diameter in accordance with ISO 3320.
All intermediate sizes up to 700 mm diameter can be supplied.Sizes > 700 mm diameter with special elastomers on request.
Busak+ Shamban
44
TurconR AQ-SealR
Bore Diameter DN H9 115.0 120.0 120.0 125.0 125.0 130.0 130.0 135.0 140.0 150.0 160.0 170.0 180.0 190.0 200.0 210.0 220.0 230.0 240.0 250.0 250.0 280.0 300.0 310.0 320.0 350.0 400.0 420.0 450.0 480.0 500.0 600.0 700.0
Groove Diameter d1 h9 94.0 104.5 99.0 109.5 104.0 114.5 109.0 114.0 119.0 129.0 139.0 149.0 159.0 169.0 179.0 189.0 199.0 209.0 219.0 229.0 225.5 252.0 272.0 282.0 292.0 322.0 372.0 392.0 422.0 445.0 465.0 565.0 665.0
Groove Width L1 +0.2 8.1 6.3 8.1 6.3 8.1 6.3 8.1 8.1 8.1 8.1 8.1 8.1 8.1 8.1 8.1 8.1 8.1 8.1 8.1 8.1 8.1 9.5 9.5 9.5 9.5 9.5 9.5 9.5 9.5 11.5 11.5 11.5 11.5
Part No.
O-Ring Dimensions 93 x 7.0 100.97 x 5.33 98 x 7.0 107.32 x 5.33 103 x 7.0 113.67 x 5.33 108 x 7.0 113.67 x 7.0 116.84 x 7.0 126.37 x 7.0 135.89 x 7.0 145.42 x 7.0 158.12 x 7.0 164.47 x 7.0 177.17 x 7.0 183.52 x 7.0 196.22 x 7.0 208.92 x 7.0 215.27 x 7.0 227.97 x 7.0 227.97 x 7.0 250 x 8.4 270 x 8.4 280 x 8.4 290 x 8.4 320 x 8.4 370 x 8.4 390 x 8.4 420 x 8.4 444 x 10.0 464 x 10.0 564 x 10.0 664 x 10.0
QUAD-RING Dimensions 107.62 x 2.62 114.02 x 1.78 107.62 x 2.62 114.02 x 1.78 113.97 x 2.62 120.37 x 1.78 120.32 x 2.62 126.67 x 2.62 126.67 x 2.62 139.37 x 2.62 145.72 x 2.62 158.42 x 2.62 171.11 x 2.62 177.47 x 2.62 190.17 x 2.62 196.52 x 2.62 202.87 x 2.62 215.57 x 2.62 221.92 x 2.62 234.62 x 2.62 234.62 x 2.62 266.29 x 3.53 278.99 x 3.53 291.69 x 3.53 304.39 x 3.53 329.79 x 3.53 380.59 x 3.53 380.59 x 3.53 430.66 x 3.53 456.06 x 5.33 456.06 x 5.33 557.58 x 5.33 658.88 x 5.33
PQ2201150 PQ1401200 PQ2201200 PQ1401250 PQ2201250 PQ1401300 PQ2201300 PQ2401350 PQ2401400 PQ2401500 PQ2401600 PQ2401700 PQ2401800 PQ2401900 PQ2402000 PQ2402100 PQ2402200 PQ2402300 PQ2402400 PQ2402500 PQ2202500 PQ3202800 PQ3203000 PQ3203100 PQ3203200 PQ3203500 PQ3204000 PQ3204200 PQ3204500 PQ5204800 PQ5205000 PQ5206000 PQ5207000
The dimensions in bold type are suitable for grooves to ISO 7425/1. bore diameter in accordance with ISO 3320.
All intermediate sizes up to 700 mm diameter can be supplied.Sizes > 700 mm diameter with special elastomers on request.
Busak+ Shamban
45
TurconR AQ-SealR
Busak+ Shamban
46
- Double Acting - Heavy Duty, High Pressure - Material - PTFE, NBR Elastomer, POM -
Busak+ Shamban
47
Busak+ Shamban
48
PHD Seal
Description The PHD Seal is a high-pressure heavy-duty piston seal with excellent leakage control and superior extrusion and wear resistance The PHD seal is a combination of a PTFE based slipper seal energised by an elastomer profile ring and completed with two Back-up rings (POM). It is manufactured with a predefined interference fit, which together with the squeeze of the elastomer part ensures a good sealing effect even at low system pressure. At higher pressures the elastomer part is energised by the system pressure and consequently activates the slipper seal in the radial direction. The Back-up rings prevent the slipper seal from extrusion and ensure a long service life even under harsh conditions. Application Examples The PHD Seal is the recommended sealing element for double acting pistons of hydraulic cylinders working in very harsh conditions such as: S Excavators S Heavy duty hydraulic cylinders Technical Data Operating conditions pressure: Up to 40 MPa Peak pressure up to 60 MPa Speed: Temperature: Media: Clearance: p Slipper seal Back-up ring Elastomer Up to 1.5 m/s -45C to +135C Mineral oil based hydraulic fluids, water/oil and glycol/oil emulsions The maximum permissible radial clearance Smax is shown in Table XXI, as a function of the operating pressure and functional diameter.
Important Note: The above data are maximum values and cannot be used at the same time. e.g. the maximum operating speed depends on material type, pressure, temperature and gap value. Temperature range also dependent on medium. Materials Standard Application: For hydraulic components:
Figure 20 PHD Seal Advantages - Simple groove design - No stick-slip effect when starting for smooth operation - Minimum static and dynamic coefficient of friction - Increased clearance possible - Due to larger extrusion gap, safe use even with soiled media - Long service life
H In mineral oils or medium with good lubricating performance H in water /oil and water/glycol emulsions Slipper Seal: Energiser: Back-up rings: Bronze filled PTFE NBR 80 Shore A POM
Material code for the set: PTNO4 Special Application: For special applications requiring other combinations, please contact your local Busak+Shamban Company. material
Busak+ Shamban
49
N T V N T V N T V N T V E**
# Limited high temperature due to POM Back-up Ring. * The Energiser Operation Temperature is only valid in mineral hydraulic oil. Highlighted material is standard. **Material not suitable for mineral oils. Material Code definition: PHD seal with slipper seal material TR55 and NBR energiser: PTN04
Busak+ Shamban
50
Installation Recommendation
R max. 0.2 S
15d-20d
DN
d1
r1
Busak+ Shamban
51
Ordering Example PHD Seal, complete. Bore diameter: DN = 80.0 mm Part No.: PKP000800 (from Table XXI) Seal: PTFE TR55 Energiser: NBR Back-up ring: POM Material set-code: PTN04 Polypac Ref. No.: PHD 8065
PKP0 0 0800 -
PTN04
Busak+ Shamban
52
R STEPSEALR 2K TURCON
- Single Acting - Rubber Energised Plastic Faced Seal - Material - TurconR, ZurconR and Elastomer -
Busak+ Shamban
53
Busak+ Shamban
54
TurconR StepsealR 2K
Operating conditions pressure: Up to 80 MPa Speed: Temperature: Media: Up to 15 m/s, frequency up to 5 Hz -45C to +200C *) Mineral oil-based hydraulic fluids, flame retardant hydraulic fluids, environmentally safe hydraulic fluids (bio-oils), water, air and others, depending on the O-Ring material (see Table XXIII) The maximum permissible radial clearance Smax is shown in Table XXIV, as a function of the operating pressure and functional diameter.
Figure 22 TurconR StepsealR 2K Advantages - High static and dynamic sealing effect - Stick-slip free operation for precise control - High abrasion resistance and high resistance to extrusion - Long service life - Simple groove design, one-piece piston possible - Wide range of application temperatures and high resistance to chemicals, depending on the choice of O-Ring material - Simple installation without seal edge deformation - Available for all diameters up to 2.700 mm - Low friction Clearance:
Important Note: The above data are maximum values and cannot be used at the same time. e.g. the maximum operating speed depends on material type, pressure, temperature and gap value. Temperature range also dependent on medium. *) In the case of unpressurized applications in temperatures below 0C please contact our application engineers for assistance !
Busak+ Shamban
55
TurconR StepsealR 2K
Materials Standard Application: H For hydraulic components in mineral oils containing zinc or medium with good lubricating performance. TurconR Seal: Energiser: TurconR T46 O-Ring NBR 70 Shore A or FKM 70 Shore A depending on the temperature T46 N or T46 V
Series Different cross-section sizes are recommended as a function of the seal diameters. These are the criteria for these recommendations. Table XXIV, shows the relationship between the series number according to the seal diameter range and the different application class sizes. These application classes are: Standard application: General applications in which no exceptional operating conditions exist. Applications with demands for reduced friction or for smaller grooves.
Set reference:
Special Application: H Non-lubricating fluids or pneumatic applications require self-lubricating sealing materials. Therefore we recommend: TurconR Seal: Energiser: TurconR T29 O-Ring NBR 70 Shore A or FKM 70 Shore A depending on the temperature T29 N or T29 V
Light application:
Heavy-duty application: For exceptional operating loads such as high pressures, pressure peaks, etc. Table XXII Available range
Series No. PSK00 PSK10 PSK20 PSK30 PSK40 PSK80 PSK50 PSK5X PSK60 PSK6X Bore Diameter DN H9 6.0 - 140.0 10.0 - 140.0 18.0 - 320.0 40.0 - 400.0 50.0 - 700.0 133.0 - 999.9 250.0 - 999.9 1000.0 - 1200.0 750.0 - 999.9 1000.0 - 2700.0
Set reference:
H Rough mating surface finish and improved leakage control ZurconR Seal: Energiser: Set reference: ZurconR Z51 O-Ring NBR 70 Shore A Z51 N
For the recommended range see Table XXIV Groove StepsealR 2K are also available on request for the groove sizes to ISO 7425/1.
Busak+ Shamban
56
TurconR StepsealR 2K
T46
N T
-10 to +200 -30 to +100 -45 to +80 -10 to +200 -30 to +100 -45 to +80 -10 to +200 -45 to +145 -30 to +100 -45 to +80 -10 to +200 -45 to +145 -30 to +100 -45 to +80 -10 to +200 -30 to +100 -45 to +80 -10 to +200 -30 to +100 -45 to +80 -10 to +200 -45 to +145 -30 to +100 -45 to +80 Steel Steel, hardened Cast iron C ti Ceramic coating Stainless steel 80 Steel Stainless steel S i l l 70 Steel tube Steel, Steel hardened Cast iron 40 Steel tube Steel, hardened 25 Steel Cast iron Stainless steel Aluminium Bronze 70 Steel Cast iron Stainless steel Aluminium Bronze Alloys 30 Steel tube Steel, hardened S l h d d Cast iron 80
ZurconR Z80 Z80 NBR-70 Shore A N -30 to +80 Steel Stainless steel For lubricating and non-lubricating hydraulic g g y Aluminium Al i i fluids, high b i fl id hi h abrasion resistance, very good it d NBR-Low temp. T -45 to +80 Bronze chemical resistance, limited temp. resistance. 70 Shore A Ceramic coating Ultra high molecular weight polyethylen Colour: White to off-white * The O-Ring Operation Temperature is only valid in mineral hydraulic oil. BAM: Tested by Bundes-anstalt Materialprfung, Highlighted materials are standard. ** Material not suitable for mineral oils. *** max. 2300 mm
45
Germany.
Busak+ Shamban
57
TurconR StepsealR 2K
Installation Recommendation
R max. 0.3 d2 S r1 d1 DN L1 Figure 23 Installation drawing Table XXIV Installation dimensions - Standard recommendations
Series No. Standard Application PSK0 PSK1 PSK2 PSK3 PSK4 PSK8 PSK5 PSK6 8 - 16.9 17 - 26.9 27 - 59.9 60 - 199.9 200 - 255.9 256 - 669.9 670 - 999.9 1000** Bore Diameter DN H9 Light Application 17 - 26.9 27 - 59.9 60 - 199.9 200 - 255.9 256 - 669.9 670 - 999.9 1000 -Heavy-Duty Application --17 - 26.9 27 - 59.9 60 - 199.9 200 - 255.9 256 - 669.9 670 - 999.9 Groove Diameter Groove Width Radius Radial Clearance S max* r1 0.4 0.6 1.0 1.3 1.8 1.8 2.5 3.0 10 MPa 0.30 0.40 0.50 0.70 0.80 0.90 1.00 1.20 20 MPa 0.20 0.25 0.30 0.40 0.60 0.70 0.80 0.90 40 MPa 0.15 0.15 0.20 0.25 0.35 0.40 0.50 0.60 O-Ring CrossSection d2 1.78 2.62 3.53 5.33 7.00 7.00 8.40 12.00 d1 h9 DN-4.9 DN-7.3 DN-10.7 DN-15.1 DN-20.5 DN-24.0 DN-27.3 DN-38.0 L1 +0,2 2.2 3.2 4.2 6.3 8.1 8.1 9.5 13.8 * At pressures > 40 MPa use diameter tolerance H8/f8 (bore/piston) in area of seal ** Energiser has a special shape.
Ordering example TurconR StepsealR 2K, complete with O-Ring, standard application, Series PSK3 (from Table XXIV). Bore diameter: DN = 80.0 mm Part No. PSK300800 (from Table XXV) Select the material from Table XXIII. The corresponding code numbers are appended to the Part No. (from Table XXV). Together they form the Order No. For all intermediate sizes not shown in Table XXV, the Order No. can be determined from the example opposite. *** For diameters 1000.0 mm multiply only by factor 1. Example: PSK6 for diameter 1200.0 mm. Order no.: PSK6X1200 - T46N.
PSK3 0 0800
T46
Type (Standard) Cylinder diameter x 10*** Quality Index (Standard) Material code (Seal ring) Material code (O-Ring)
Busak+ Shamban
58
TurconR StepsealR 2K
Table XXV
Bore Dia. DN H9 9.0 10.0 12.0 14.0 15.0 16.0 18.0 20.0 20.0 22.0 25.0 25.0 28.0 30.0 30.0 32.0 32.0 35.0 40.0 40.0 42.0 45.0 48.0 50.0 50.0 52.0 55.0 60.0 63.0 63.0 65.0 70.0 70.0 75.0 80.0 80.0 85.0 85.0 90.0 90.0 95.0 95.0
Groove Dia. d1 h9 4.1 5.1 7.1 9.1 10.1 11.1 10.7 15.1 12.7 14.7 17.7 14.3 17.3 22.7 19.3 24.7 21.3 24.3 32.7 29.3 31.3 34.3 37.3 39.3 34.9 41.3 44.3 44.9 52.3 47.9 49.9 59.3 54.9 59.9 64.9 59.5 69.9 64.5 74.9 69.5 79.9 74.5
Busak+ Shamban
59
TurconR StepsealR 2K
Bore Dia. DN H9 280.0 300.0 306.0 310.0 320.0 320.0 330.0 340.0 345.0 350.0 360.0 370.0 380.0 400.0 420.0 430.0 440.0 450.0 480.0 500.0 520.0 540.0 600.0 650.0 700.0 800.0 860.0 900.0 920.0 1000.0 1000.0 1200.0 1200.0 1500.0 2000.0 2700.0
Groove Dia. d1 h9 256.0 276.0 285.5 286.0 299.5 296.0 306.0 316.0 324.5 326.0 336.0 346.0 356.0 376.0 396.0 406.0 416.0 426.0 456.0 476.0 499.5 516.0 576.0 626.0 672.7 772.7 832.7 872.7 892.7 972.7 962.0 1172.7 1162.0 1462.0 1962.0 2662.0
Groove Width L1 +0.2 8.1 8.1 8.1 8.1 8.1 8.1 8.1 8.1 8.1 8.1 8.1 8.1 8.1 8.1 8.1 8.1 8.1 8.1 8.1 8.1 8.1 8.1 8.1 8.1 9.5 9.5 9.5 9.5 9.5 9.5 13.8 9.5 13.8 13.8 13.8 13.8
Part No.
O-Ring* Dimensions
PSK802800 PSK803000 PSK403060 PSK803100 PSK403200 PSK803200 PSK803300 PSK803400 PSK403450 PSK803500 PSK803600 PSK803700 PSK803800 PSK804000 PSK804200 PSK804300 PSK804400 PSK804500 PSK804800 PSK805000 PSK405200 PSK805400 PSK806000 PSK806500 PSK507000 PSK508000 PSK508600 PSK509000 PSK509200 PSK5X1000 PSK6X1000 PSK5X1200 PSK6X1200 PSK6X1500 PSK6X2000 PSK6X2700
253.37 x 7.0 266.07 x 7.0 278.77 x 7.0 278.77 x 7.0 291.47 x 7.0 291.47 x 7.0 304.17 x 7.0 316.87 x 7.0 316.87 x 7.0 316.87 x 7.0 329.57 x 7.0 342.27 x 7.0 354.97 x 7.0 367.67 x 7.0 393.07 x 7.0 405.26 x 7.0 405.26 x 7.0 417.96 x 7.0 456.06 x 7.0 468.76 x 7.0 494.16 x 7.0 506.86 x 7.0 557.66 x 7.0 608.08 x 7.0 670 x 8.4 770 x 8.4 830 x 8.4 870 x 8.4 890 x 8.4 970 x 8.4 960 x 12.0 1170 x 8.4 1160 x 12.0 1460 x 12.0 1960 x 12.0 2660 x 12.0
The bore diameters in bold type comply with the recommendations of ISO 3320. Other dimensions and all intermediate sizes up to 2700 mm diameter including imperial (inch) sizes can be supplied. All O-Rings with 12 mm cross section are delivered as special Profilring.
Busak+ Shamban
60
R STEPSEALR K TURCON
- Single Acting - Rubber Energised Plastic Faced Seal - Material - TurconR, ZurconR and Elastomer -
Busak+ Shamban
61
Busak+ Shamban
62
TurconR StepsealR K
TurconRStepsealRK
Description The StepsealR K is a single-acting seal element consisting of a seal ring of high-grade TurconR or ZurconR materials and an O-Ring as energizing element. The StepsealR K was originally developed and patented (Patent No. P3225906) by Busak+Shamban as a rod seal. Due to its outstanding properties, however, it is equally well suited as a single-acting piston seal where high demands are made on positional accuracy and free movement. Application Examples The TurconR StepsealR K is the recommended sealing element for single acting pistons in hydraulic components for: S Injection moulding machines S Machine tools S Presses It is particularly recommended in floating piston accumulators as primary seal on the oil side in combination with AQ-SealR and AQ-SealR 5. Technical Data
Turconr Seal ring O-Ring
Operating conditions pressure: Up to 80 MPa Speed: Temperature: Media: Up to 15 m/s, frequency up to 5 Hz -45C to +200C *) Mineral oil-based hydraulic fluids, flame retardant hydraulic fluids, environmentally safe hydraulic fluids (bio-oils), water, air and others, depending on the O-Ring material (see Table XXVI) The maximum permissible radial clearance Smax is shown in Table XXVII, as a function of the operating pressure and functional diameter.
Figure 24 TurconRStepsealRK Advantages - High static and dynamic sealing effect - Stick-slip free operation for precise control - High abrasion resistance and resistance to extrusion - Long service life - Simple groove design, one-piece piston possible - Wide range of application temperatures and high resistance to chemicals, depending on the choice of O-Ring material - Simple installation without seal edge deformation due to the K-edge - Available for all diameters up to 2.700 mm Clearance:
Important Note: The above data are maximum values and cannot be used at the same time. e.g. the maximum operating speed depends on material type, pressure, temperature and gap value. Temperature range also dependent on medium. *) In the case of unpressurized applications in temperatures below 0C please contact our application engineers for assistance !
Busak+ Shamban
63
TurconR StepsealR K
Materials Standard Application: H For hydraulic components in mineral oils containing zinc or medium with good lubricating performance. TurconR Seal: Energiser: TurconR T46 O-Ring NBR 70 Shore A or FKM 70 Shore A depending on the temperature T46 N or T46 V
Set reference:
Special Application: H Non-lubricating fluids or pneumatic applications require self-lubricating sealing materials. Therefore we recommend: TurconR Seal: Energiser: TurconR T29 O-Ring NBR 70 Shore A or FKM 70 Shore A depending on the temperature T29 N or T29 V
Set reference:
H Rough mating surface finish and improved leakage control ZurconR Seal: Energiser: Set reference: Groove StepsealR K are also available on request for the groove sizes to ISO 7425/1. ZurconR Z51 O-Ring NBR 70 Shore A Z51 N
Busak+ Shamban
64
TurconR StepsealR K
T46
N T
-10 to +200 -30 to +100 -45 to +80 -10 to +200 -30 to +100 -45 to +80 -10 to +200 -45 to +145 -30 to +100 -45 to +80 -10 to +200 -45 to +145 -30 to +100 -45 to +80 -10 to +200 -30 to +100 -45 to +80 -10 to +200 -30 to +100 -45 to +80 -10 to +200 -45 to +145 -30 to +100 -45 to +80 Steel Steel, hardened Cast i C t iron Ceramic coating Stainless steel 80 Steel Stainless steel St i l t l 60 Steel tubes Steel, Steel hardened Cast iron 30 Steel tubes Steel, hardened S l h d d 20 0 Steel Cast iron Stainless steel Aluminium Bronze B 60 Steel Cast iron Stainless steel Aluminium Bronze B Alloys 25 S ee ubes Steel tubes Steel, hardened S l h d d Cast iron 80
ZurconR Z80 Z80 NBR - 70 Shore A N -30 to +80 Steel 40 Stainless steel For lubricating and non-lubricating hydraulic Aluminium fluids, high abrasion resistance, very good Bronze chemical resistance, limited temperature NBR - Low temp. T -45 to +80 Ceramic coating resistance. 70 Shore A Ultra high molecular weight polyethylen Colour: White to off-white * The O-Ring Operation Temperature is only valid in mineral hydraulic oil. BAM: Tested by Bundes Anstalt Materialprfung, Germany. Highlighted materials are standard. **Material not suitable for mineral oils. *** max. 2300 mm
Busak+ Shamban
65
TurconR StepsealR K
Installation Recommendation (for new Constructions please apply TurconR StepsealR 2K)
R max. 0.3 d2 S r1 DN d1 L1 Figure 25 Installation drawing Table XXVII Installation Dimensions - Standard Recommendations
Bore Diameter DN H9 Series No. PS 14 Standard Application 8 - 16.9 17 - 26.9 27 - 59.9 60 - 199.9 200 - 255.9 256 - 669.9 670 - 999.9 Series No. PS 16 Light Application 17 - 26.9 27 - 59.9 60 - 199.9 200 - 255.9 256 - 669.9 670 - 999.9 -Series No. PS 12 Heavy-Duty Application --17 - 26.9 27 - 59.9 60 - 199.9 200 - 255.9 256 - 669.9 Groove Diameter Groove Width Radius Radial Clearance S max* O-Ring Cross Sec. d1 h9 DN-4.9 DN-7.3 DN-10.7 DN-15.1 DN-20.5 DN-24.0 DN-27.3 DN-38.0 L1 +0.2 2.2 3.2 4.2 6.3 8.1 8.1 9.5 13.8 r1 0.4 0.6 1.0 1.3 1.8 1.8 2.5 3.0 10 MPa 0.30 0.40 0.40 0.50 0.60 0.60 0.70 1.00 20 MPa 0.20 0.25 0.25 0.30 0.35 0.35 0.50 0.70
1000**
* At pressures > 40 MPa use diameter tolerance H8/f8 (bore/piston) in area of the seal.
Ordering Example TurconR StepsealR K, complete with O-Ring, standard application, Series PS14 (from Table XXVII). Bore diameter: DN = 80.0 mm Part No. PS1400800 (from Table XXVIII) Select the material from Table XXVI. The corresponding code numbers are appended to the Part No. (from Table XXVIII). Together they form the Order No. For all intermediate sizes not shown in Table XXVIII, the Order No. can be determined from the example opposite. *** For diameters 1000.0 mm multiply only by factor 1. Example: PS14 for diameter 1200.0 mm. Order no.: PS14X1200 - T46N.
PS14
0 0800
T46
Type (Standard) Cylinder diameter x 10*** Quality Index (Standard) Material code (Seal ring) Material code (O-Ring)
Busak+ Shamban
66
TurconR StepsealR K
Busak+ Shamban
67
TurconR StepsealR K
Bore Dia. DN H9 280.0 300.0 306.0 310.0 320.0 320.0 330.0 340.0 345.0 350.0 360.0 370.0 380.0 400.0 420.0 430.0 440.0 450.0 480.0 500.0 520.0 540.0 600.0 650.0 700.0 800.0 860.0 900.0 920.0 1000.0 1000.0 1200.0 1200.0 1500.0 2000.0 2700.0
Groove Dia. d1 h9 256.0 276.0 285.5 286.0 299.5 296.0 306.0 316.0 324.5 326.0 336.0 346.0 356.0 376.0 396.0 406.0 416.0 426.0 456.0 476.0 499.5 516.0 576.0 626.0 672.7 772.7 832.7 872.7 892.7 972.7 962.0 1172.7 1162.0 1462.0 1962.0 2662.0
Groove Width L1 +0.2 8.1 8.1 8.1 8.1 8.1 8.1 8.1 8.1 8.1 8.1 8.1 8.1 8.1 8.1 8.1 8.1 8.1 8.1 8.1 8.1 8.1 8.1 8.1 8.1 9.5 9.5 9.5 9.5 9.5 9.5 13.8 9.5 13.8 13.8 13.8 13.8
Part No.
O-Ring Dimensions 253.37 x 7.0 266.07 x 7.0 278.77 x 7.0 278.77 x 7.0 291.47 x 7.0 291.47 x 7.0 304.17 x 7.0 316.87 x 7.0 316.87 x 7.0 316.87 x 7.0 329.57 x 7.0 342.27 x 7.0 354.97 x 7.0 367.67 x 7.0 393.07 x 7.0 405.26 x 7.0 405.26 x 7.0 417.96 x 7.0 456.06 x 7.0 468.76 x 7.0 494.16 x 7.0 506.86 x 7.0 557.66 x 7.0 608.08 x 7.0 670 x 8.4 770 x 8.4 830 x 8.4 870 x 8.4 890 x 8.4 970 x 8.4 960 x 12.0 1170 x 8.4 1160 x 12.0 1460 x 12.0 1960 x 12.0 2660 x 12.0
PS1402800 PS1403000 PS1603060 PS1403100 PS1603200 PS1403200 PS1403300 PS1403400 PS1603450 PS1403500 PS1403600 PS1403700 PS1403800 PS1404000 PS1404200 PS1404300 PS1404400 PS1404500 PS1404800 PS1405000 PS1605200 PS1405400 PS1406000 PS1406500 PS1407000 PS1408000 PS1408600 PS1409000 PS1409200 PS16X1000 PS14X1000 PS16X1200 PS14X1200 PS14X1500 PS14X2000 PS14X2700
The bore diameters in bold type comply with the recommendations of ISO 3320. Other dimensions and all intermediate sizes up to 2.700 mm diameter including imperial (inch) sizes can be supplied. All O-Rings with 12 mm cross section are delivered as special profilring.
Busak+ Shamban
68
- Double Acting - Rubber Energised Plastic Faced Seal - For O-Ring Grooves - Material - TurconR and Elastomer Edition November 2003
Busak+ Shamban
69
Busak+ Shamban
70
Notches
Figure 27 TurconR Double DeltaR with notches Advantages Pressure Compact groove dimensions and simple installation Low friction without stick-slip Resistance against wear and extrusion Piston seals available for all diameters from 5 to 999.9 mm - Standard cross sections cover AS 568A and important metric O-Rings, other cross sections available on request. - Fits also groove dimensions per MIL-G-5514F Application Examples The TurconR Double DeltaR is the recommended sealing element for double acting pistons of hydraulic or pneumatic cylinders in sectors such as: S Machine tools S Handling devices S Manipulators S Valves S Chemical process equipment It is particular recommended for light duty and small diameter applications.
Figure 26 TurconR Double DeltaR without and with pressure Notches TurconR Double DeltaR is as standard supplied without radial notches, as the thin radial section of the seal gives good response to pressure variations. For diameters from 8 mm notches on both sides are optional. These ensure direct pressurizing of the seal under all operating conditions.
Busak+ Shamban
71
Technical Data Operating conditions Pressure: Velocity: Temperature: Media: Up to 35 MPa Up to 15 m/s -45_C to +200_C (according to O-Ring material) Mineral oil, Non-flammable fluids, Environmentally safe fluids and others according to O-Ring material.
H For specific applications other material combinations as listed may also be used. Please contact your local Busak+Shamban Company. Material for the seal set: Example: T05 plus FKM - O-Ring T46 plus NBR - O-Ring T05V T46N
Design Instructions
Lead-in Chamfers In order to avoid damage to the seal during installation, lead-in chamfers and rounded edges must be provided on the bore or piston rod (Figure 28). The minimum lead-in chamfer depends on the profile size of the seal and can be seen from the following tables. Table XXIX Lead-in Chamfers
Important Note: The above data are maximum values and cannot be used at the same time. e.g. the maximum operating speed depends on material type, pressure, temperature and gap value. Temperature range also dependent on medium.
Materials
Standard Application: H For hydraulic components with reciprocating movement in mineral oils containing zinc or medium with good lubricating performance and hard mating surface. TurconR Seal: Energiser: TurconR T46 O-Ring NBR 70 Shore A or FKM 70 Shore A depending on the temperature
Lead-in Chamfer* Diameter increase DN min. 1.4 1.8 2.4 3.2 4.0
O-Ring Cross Section** d2 1.78 - 2.00 2.40 - 2.62 3.00 - 4.00 5.00 - 5.70 7.00 - 8.40
* Though not less than 1.5 % of bore diameter (bore/rod diameter). **The O-Ring cross section d2 can be found in the appropriate tables Installation Dimensions, XXXI, XXXIII and XXXIV.
Special Application: H Short stroke movements, poor lubricating fluids and soft mating surfaces. TurconR seal: Energiser: TurconR T24 O-Ring NBR 70 shore A or FKM 70 shore A (depending on the temp.) 15d-20d D/2 rounded, polished
H For low friction requirement in dynamic hydraulic components with good lubricating medium: TurconR seal: Energiser: TurconR T05 O-Ring NBR 70 shore A or FKM 70 shore A (depending on the temp.) Figure 28 Lead-in chamfers
Busak+ Shamban
72
Materials
Table XXX Turcon Materials for Double Delta
Material, Applications, Properties Turcon T46 Standard material for hydraulics, high compressive strength, good sliding and wear properties, good extrusion resistance, BAM tested. Bronze filled Colour: Greyish to dark brown Turcon T24 For ll l b i i F all lubricating and non-lubricating d l bi i hydraulic fluids, soft mating surfaces. Carbon filled Colour: Black Turcon T05 For all lubricating hydraulic fl d h d ll l b h d l fluids, hard mating surfaces, very good sliding properties, low friction. Colour: Turquoise Code O-Ring Material Code O-Ring Operating Temp.* C -30 to +100 -45 to +80 Mating Surface Material Steel tubes Steel, hardened Cast iron MPa max. 35
T46
N T
V N T V E** N T V
-10 to +200 -30 to +100 -45 to +80 -10 to +200 -45 to +145 -30 to +100 -45 to +80 -10 to +200 S ee Steel Steel, hardened S l h d d Cast iron Stainless steel Aluminium Bronze Steel tubes Steel, hardened S l h d d 25 5
T24
NBR - 70 Shore A NBR - Low temp. 70 Shore A FMK - 70 Shore A EPDM - 70 Shore A
T05 05
20 0
* The O-Ring Operation Temperature is only valid in mineral hydraulic oil. BAM: Tested by Bundes Anstalt Materialprfung, Germany. Highlighted materials are standard. **Material not suitable for mineral oils.
Busak+ Shamban
73
Installation Recommendation
r max. 0.3 d2 S p r1
DN
d1
L1
r1
Ordering example TurconR Double DeltaR, complete with O-Ring, standard range, series PDD3 (from Table XXXI). Bore diameter: DN = 80.0 mm Part No.: PDD300800 (from Table XXXII) Select the material from Table XXX. The corresponding code numbers are appended to the Part No. (from Table XXXII). Together they form the Order No. For all intermediate sizes not shown in Table XXXII, the Order No. can be determined from the example opposite. * N for seals with notches. Available for diameters from 8.0 mm. For seals for other groove widths/Dimensions please refer to table XXXIII and XXXIV.
PDD3 0 0800 -
T05
Type (Standard)* Cylinder diameter x 10 Quality Index (Standard) Material code (Seal ring) Material code (O-Ring)
Busak+ Shamban
74
The bore diameters in bold type comply with the recommendations of ISO 3320. Part No. for other dimensions and all intermediate dimensions up to 999.9 mm diameter including imperial (inch) dimensions can be supplied. Larger dimensions up to 2700 mm available upon request.
Busak+ Shamban
75
L3
L3
PDA3 0 0800 -
T05
*** From table XXX N for seals with notches, available from dia. 8mm
0 0 0 0 0 0
N N N N N N
TurconR Double DeltaR for metric O-Rings Double DeltaR is available for installation in grooves for metric O-Rings as listed in Table XXXIV. Table XXXIV Seals for Metric O-Ring Grooves
O-Ring Cross-Section d2 Groove Diameter d1 h9 Groove Width L1 +0.2 Series No. Execution Mark 5th digit Standard Notch* Available Range
0 0 0 0 0 0 0
N N N N N N N
Busak+ Shamban
76
R VARISEALR M2 TURCON
- Single Acting - Spring Energised Plastic U-Cup - Material - TurconR and ZurconR -
Busak+ Shamban
77
Busak+ Shamban
78
TurconR VarisealR M2
TurconR VarisealR M2
Description The TurconR VarisealR M2 is a single-acting seal consisting of a U-shaped seal jacket and a V-shaped corrosion resistant spring. The characteristic of the VarisealR M2 is the newly developed asymmetric seal profile, where the dynamic lip has an optimized short and heavy profile, offering reduced friction and long service life. Advantages - Resistant to most fluids and chemicals - Low coefficients of friction - Stick-slip free operating for precise control - High abrasion resistance and dimensional stability - Can handle rapid changes in temperature - No contamination in contact with foodstuffs, pharmaceutical and medicinal fluids p TurconR Seal ring V-shaped spring - Sterilisable - Unlimited shelf life Application Examples The TurconR VarisealR M2 is the recommended sealing element for all applications requiring stick-slip free operation as well as chemical resistance against almost all media such as: Figure 31 TurconRVarisealRM2 At low and zero pressure, the metal spring provides the primary sealing force. As the system pressure increases, the main sealing force is achieved by the system pressure and ensures a tight seal from zero to high pressure. The possibility of matching suitable materials for the seal and the spring allows use in a wide range of applications going beyond the field of hydraulics, e.g. in the chemical, pharmaceutical and foodstuffs industry. The VarisealR M2 can be sterilized and is available in a special Hi-Clean version where the spring cavity is filled with a Silicone gel preventing contaminants from being entrapped in the seal. This design also works well in applications involving mud, slurries or adhesives to keep grit from packing into the seal cavity and inhibiting the spring action. For applications with highly viscous media, please contact our Technical department. VarisealR M2 seals can be installed in grooves to MIL G 5514F and ISO 3771. The seal can only be installed to a limited extent in closed grooves. Installation instructions, see Table VII. S Valves S Pumps S Separators S Actuators S Dosing devices It requires a mating surface of high quality to avoid high wear rates. Technical Data Operating conditions pressure: For dynamic loads: 45 MPa Speed: Temperature: Up to 15 m/s -70 C to +260 C For specific applications at lower temperatures, please enquire Media: Practically all fluids, chemicals and gases
Important Note: The above data are maximum values and cannot be used at the same time. e.g. the maximum operating speed depends on material type, pressure, temperature and gap value. Temperature range also dependent on medium.
Busak+ Shamban
79
TurconR VarisealR M2
Materials All materials used are physiologically safe. They contain no odour or taste-affecting substances. The following material combination has proved effective for most fluid applications: Seal ring: Spring: TurconR T 40 Stainless steel, Material No. AISI 301 Material code S
For use in accordance with the demands of the Food and Drug Administration, suitable materials are available on request. Turcon and Zurcon Materials for Variseal M2
Code Spring Material AISI 301 Code Operating Temp.* C S -70 to +260 Mating Surface Material Steel Cast iron Stainless steel Aluminium Al i i Bronze Alloys Steel tubes Steel, Steel hardened MPa max. 45
Table XXXV
Material, Applications, Properties
Turcon T40 For ll l b i ti F all lubricating and non-lubricating d l b i ti hydraulic fluids, water hydraulic, soft mating surfaces. Carbon fibre filled Colour: Grey Turcon T05 For all lubricating hydraulic fluids, hard fluids mating surfaces, very good sliding properties, l ti low f i ti friction. Colour: Turquoise ZurconR Z80 For lubricating and non-lubricating hydraulic fluids, high abrasion resistance, very good chemical resistance, limited temperature h i l it li it d t t resistance .FDA compliance. Ultra high molecular weight polyethylen Colour: White to off-white * Depending on media. Highlighted materials are standard.
T40
T05
AISI 301
-70 to +260
20
Z80
AISI 301
-70 to +80
40
Busak+ Shamban
80
TurconR VarisealR M2
Installation Recommendation
Step2) Height
Radial Clearance S max* <2 MPa 0.20 0.25 0.35 0.50 0.60 0.90 <10 MPa 0.10 0.15 0.20 0.25 0.30 0.50 <20 MPa 0.08 0.10 0.15 0.20 0.25 0.40 <40 MPa 0.05 0.07 0.08 0.10 0.12 0.20
Range 6.0 - 40.0 10.0 - 200.0 16.0 - 400.0 28.0 - 700.0 45.0 - 999.9 100.0 - 2500.0
*At pressures > 40 MPa use diameter tolerance H8/f8 (bore/piston) in area of the seal. 1) Available on request. 2) Ymax = 0.035 x D N
Ordering example TurconR VarisealR M2, standard range, Series PVA3 (from Table XXXVI). Bore diameter: DN = 80.0 mm Part No.: PVA300800 (from Table XXXVII) Select the material from Table XXXV. The corresponding code numbers are appended to the Part No. (from Table XXXVII). Together they form the Order No. For all intermediate sizes not shown in Table XXXVII, the Order No. can be determined from the example opposite. ** For diameters 1000.0 mm multiply only by factor 1. Example: PVA5 for diameter 1200.0 mm. Order no.: PVA5X1200 - T40S.
PVA3
0 0800
T40
Type (Standard) Cylinder diameter x 10** Quality Index (Standard) Material code (Seal ring) Material code (Spring)
Busak+ Shamban
81
TurconR VarisealR M2
The bore diameters in bold type comply with the recommendations of ISO 3320. Other dimensions and all intermediate sizes up to 2.700 mm diameter including imperial (inch) sizes can be supplied.
Busak+ Shamban
82
Busak+ Shamban
83
Busak+ Shamban
84
Figure 33 Piston U-Cup Type PUA Advantages - Simple groove design - High abrasion resistance - Long service life - Effective sealing effect even with non excellent mating surface finish Application Examples The U-Cup is the recommended sealing element for single acting pistons of hydraulic components such as: S Presses S Lift platforms S Aftermarket
30 40
Important Note: The above data are maximum values and cannot be used at the same time. e.g. the maximum operating speed depends on material type, pressure, temperature and gap value. Temperature range also dependent on medium. Materials Standard Material: H For hydraulic components in mineral oils or medium with good lubricating performance, polyurethane 93 Shore A ZurconR Colour: Z20 turquoise
Busak+ Shamban
85
Ordering Example Bore diameter: Groove diameter: Groove width: Part number: Material code: DN = 80 mm d1 = 65 mm L1 = 13 mm PUA100800 (Table XXXIX) Z20 Order No. Series No. Execution code Bore diameter x 10 Quality Index (standard) Material code PUA 1 00800 Z20
Busak+ Shamban
86
Installation Recommendation
L1 r max. 0.3 T S
r max. 0.3
d2 min.
d1
Busak+ Shamban
87
DN
Bore Dia. DN H9 35.0 36.5 37.0 38.0 40.0 40.0 40.0 40.0 40.0 40.0 42.0 42.0 43.0 44.0 44.0 45.0 45.0 50.0 50.0 50.0 50.0 50.0 50.0 50.0 50.0 50.0 50.0 50.8 52.0 52.0 55.0 55.0 55.0 60.0 60.0 60.0 60.0 60.0 60.0 60.0 60.0 63.0 63.0 63.0 63.0
Groove Dia. d1 h9 27.0 24.0 21.0 31.0 25.0 30.0 30.0 32.0 32.0 33.0 32.0 34.5 25.0 20.0 25.0 28.5 30.0 30.0 32.0 35.0 35.0 40.0 40.0 40.0 42.0 42.0 42.0 40.8 42.0 42.0 40.0 45.0 47.0 40.0 40.0 40.0 45.0 50.0 50.0 50.0 52.0 43.0 45.0 45.0 48.0
Seal Width T 10.0 6.2 12.0 4.7 10.0 6.5 10.0 5.5 8.0 8.0 10.0 4.2 9.0 11.0 11.0 12.0 10.0 12.0 10.0 8.5 10.0 5.0 8.0 10.0 5.5 8.0 10.0 7.0 5.7 10.0 10.0 10.0 5.7 10.0 12.0 13.5 10.0 5.0 7.0 10.0 8.0 12.0 10.0 12.0 8.5
Groove Width L1 +0.2 11.0 7.0 13.0 5.2 11.0 7.5 11.0 6.5 9.0 9.0 11.0 4.7 10.0 12.0 12.0 13.0 11.0 13.0 11.0 9.5 11.0 5.5 9.0 11.0 6.0 9.0 11.0 8.0 6.5 10.6 11.0 11.0 6.3 11.0 13.0 14.5 11.0 5.5 8.0 11.0 9.0 13.0 11.0 13.0 9.5
Fitting Dia. d2 min 31.0 28.0 25.0 34.0 30.0 34.0 34.0 36.0 36.0 36.0 36.0 38.0 29.0 25.0 30.0 33.0 35.0 35.0 37.0 40.0 40.0 44.0 44.0 44.0 45.0 45.0 45.0 45.0 46.0 46.0 45.0 48.0 50.0 45.0 45.0 45.0 50.0 54.0 54.0 54.0 55.0 47.0 50.0 50.0 53.0
Part No.
B+S
Sealing Parts Ref. No. RSE 35 27 RSE 36.5 24 RSE 37 21 RSE 38 31 RSE 40 25 RSE 40 30/1 RSE 40 30 RSE 40 32 RSE 40 33 RSE 42 32 RSE 42 34.5 RSE 43 25
PUA200350 PUA000365 PUA000370 PUA000380 PUA000400 PUA200400 PUA500400 PUA300400 PUA100400 PUA400400 PUA000420 PUA100420 PUA000430 PUA000440 PUA100440 PUA000450 PUA100450 PUA500500 PUA600500 PUA100500 PUA200500 PUA000500 PUA800500 PUA400500 PUA900500 PUA700500 PUA300500 PUA100508 PUA000520 PUA100520 PUA000550 PUA100550 PUA200550 PUA200600 PUA100600 PUA400600 PUA500600 PUA300600 PUA000600 PUA600600 PUA700600 PUA800630 PUA700630 PUA600630 PUA400630
* * * * * * * *
* * *
* * * * * * * * * * *
RSE 50 35/1 RSE 50 35 RSE 50 40/1 RSE 50 40 RSE 50 42/2 RSE 50 42/1 RSE 50 42 RSE 50.8 40.8 RSE 52 42 RSE 55 40 RSE 55 47 RSE 60 40 RSE 60 40/1 RSE 60 45 RSE 60 50/1 RSE 60 50 RSE 60 50/2 RSE 60 52 RSE 63 43 RSE 63 45
* *
Busak+ Shamban
88
Bore Dia. DN H9 63.0 63.0 63.0 63.0 63.0 65.0 65.0 65.0 65.0 65.0 65.0 68.0 70.0 70.0 70.0 70.0 70.0 70.0 70.0 70.0 70.0 72.0 75.0 75.0 75.0 75.0 75.0 75.0 75.0 76.0 80.0 80.0 80.0 80.0 80.0 80.0 80.0 80.0 80.0 85.0 85.0 85.0 85.0 85.0 90.0
Groove Dia. d1 h9 48.0 48.0 53.0 53.0 53.0 45.0 45.0 50.0 50.0 55.0 55.0 48.0 50.0 50.0 50.0 55.0 55.0 60.0 60.0 60.0 62.0 58.0 50.0 55.0 65.0 65.0 65.0 65.0 65.0 56.0 60.0 60.0 60.0 60.0 65.0 68.0 70.0 70.0 72.0 65.0 65.0 70.0 75.0 75.0 70.0
Seal Width T 10.0 12.0 6.3 7.0 12.0 12.0 13.5 10.0 11.5 10.0 13.5 10.0 12.0 13.5 15.0 9.5 12.0 7.0 12.0 13.5 7.5 12.0 14.0 13.5 5.0 6.7 10.0 7.0 13.5 12.0 10.0 11.5 12.0 13.5 12.0 8.5 12.0 7.0 12.0 12.0 13.5 12.0 10.0 12.0 12.0
Groove Width L1 +0.2 11.0 13.0 7.0 8.0 13.0 13.0 14.5 11.0 12.5 11.0 14.5 11.0 13.0 14.5 16.0 10.5 13.0 8.0 13.0 14.5 8.5 13.0 15.0 14.5 5.5 7.5 11.0 8.0 14.5 13.0 11.0 12.5 13.0 14.5 13.0 9.5 13.0 8.0 13.0 13.0 14.5 13.0 11.0 13.0 13.0
Fitting Dia. d2 min 53.0 53.0 57.0 57.0 57.0 50.0 50.0 55.0 55.0 59.0 59.0 53.0 55.0 55.0 55.0 60.0 60.0 64.0 64.0 64.0 65.0 62.0 55.0 60.0 69.0 69.0 69.0 69.0 69.0 61.0 65.0 65.0 65.0 65.0 70.0 72.0 74.0 74.0 75.0 70.0 70.0 75.0 79.0 79.0 75.0
Part No.
B+S
PUA300630 PUA000630 PUA500630 PUA200630 PUA100630 PUA000650 PUA300650 PUA100650 PUA200650 PUA400650 PUA500650 PUA000680 PUA000700 PUA200700 PUA500700 PUA600700 PUA400700 PUA100700 PUA700700 PUA800700 PUA300700 PUA000720 PUA000750 PUA100750 PUA200750 PUA300750 PUA400750 PUA500750 PUA600750 PUA000760 PUA400800 PUA500800 PUA000800 PUA200800 PUA100800 PUA300800 PUA700800 PUA600800 PUA800800 PUA100850 PUA200850 PUA300850 PUA400850 PUA000850 PUA100900 * * * * * * * * * * * * * * * * * * * *
RSE 63 48 RSE 63 53 RSE 63 53/1 RSE 65 45/1 RSE 65 45 RSE 65 50 RSE 65 50/1 RSE 65 55/1 RSE 65 55 RSE 68 48 RSE 70 50 RSE 70 50/1 RSE 70 50/2 RSE 70 55/1 RSE 70 55 RSE 70 60 RSE 70 60/1 RSE 70 60/2 RSE 70 62 RSE 72 58 RSE 75 50 RSE 75 55 RSE 75 65/1 RSE 75 65/3 RSE 75 65/2 RSE 75 65/4 RSE 75 65 RSE 80 60 RSE 80 60/1 RSE 80 65 RSE 80 70/1 RSE 80 70 RSE 80 72 RSE 85 65 RSE 85 75/1 RSE 85 75 RSE 90 70
Busak+ Shamban
89
Bore Dia. DN H9 90,0 90,0 90,0 90,0 90,0 95,0 95,0 95,0 95,0 95,0 95,0 100,0 100,0 100,0 100,0 100,0 100,0 100,0 100,0 100,0 100,0 101,6 105,0 110,0 110,0 110,0 110,0 115,0 115,0 115,0 120,0 120,0 120,0 120,0 120,0 125,0 125,0 125,0 125,0 125,0 125,0 125,0 130,0 140,0 150,0
Groove Dia. d1 h9 70,0 75,0 80,0 80,0 80,0 75,0 80,0 85,0 85,0 85,0 85,0 80,0 80,0 80,0 80,0 85,0 85,0 86,0 88,0 90,0 90,0 80,0 90,0 90,0 95,0 100,0 100,0 100,0 100,0 105,0 95,0 100,0 100,0 103,0 105,0 100,0 105,0 105,0 110,0 110,0 115,0 115,0 110,0 120,0 130,0
Seal Width T 13,5 12,0 5,0 10,0 13,0 13,5 12,0 6,7 7,0 8,5 13,5 10,0 11,5 12,0 13,5 8,5 12,0 12,0 8,5 7,0 10,5 12,0 12,0 12,0 12,0 7,0 13,5 10,5 12,0 13,5 12,0 12,0 13,5 16,0 12,0 15,0 12,0 15,0 10,0 12,0 7,0 15,0 15,0 12,0 15,0
Groove Width L1 +0.2 14,5 13,0 5,5 11,0 14,0 14,5 13,0 7,5 8,0 9,5 14,5 11,0 12,5 13,0 14,5 9,5 13,0 13,0 9,5 8,0 11,5 13,0 13,0 13,0 13,0 8,0 14,5 11,5 13,0 14,5 13,0 13,0 14,5 17,0 13,0 16,0 13,0 16,0 11,0 13,0 8,0 16,0 16,0 13,0 16,0
Fitting Dia. d2 min 75,0 80,0 84,0 84,0 84,0 80,0 85,0 89,0 89,0 89,0 89,0 85,0 85,0 85,0 85,0 90,0 90,0 90,0 93,0 94,0 94,0 85,0 95,0 95,0 100,0 104,0 104,0 105,0 105,0 109,0 100,0 105,0 105,0 108,0 110,0 105,0 110,0 110,0 115,0 115,0 119,0 119,0 115,0 125,0 135,0
Part No.
B+S
PUA200900 PUA300900 PUA500900 PUA000900 PUA400900 PUA100950 PUA000950 PUA200950 PUA300950 PUA400950 PUA500950 PUA501000 PUA201000 PUA001000 PUA601000 PUA301000 PUA401000 PUA701000 PUA101000 PUA801000 PUA901000 PUA001016 PUA001050 PUA001100 PUA101100 PUA201100 PUA301100 PUA101150 PUA001150 PUA201150 PUA401200 PUA001200 PUA101200 PUA501200 PUA301200 PUA201250 PUA301250 PUA001250 PUA101250 PUA401250 PUA501250 PUA601250 PUA001300 PUA001400 PUA101500 * * * * * * * * * * * * * * * * * * *
RSE 90 75 RSE 90 80/2 RSE 90 80/1 RSE 90 80 RSE 95 75 RSE 95 85/2 RSE 95 85 RSE 95 85/1 RSE 95 85/3 RSE 100 80/2 RSE 100 80 RSE 100 80/1 RSE 100 85 RSE 100 86 RSE 100 90 RSE 100 90/1 RSE 101.6 80 RSE 105 90 RSE 110 90 RSE 110 95 RSE 110 100 RSE 110 100/1 RSE 115 100 RSE 115 105 RSE 120 95 RSE 120 100 RSE 120 100/1 RSE 120 103 RSE 125 105 RSE 125 105/1 RSE 125 115 RSE 125 115/1 -
Busak+ Shamban
90
Groove Width L1 +0.2 12,5 16,0 12,5 20,0 16,0 20,0 16,0
Fitting Dia. d2 min 145,0 150,0 165,0 175,0 180,0 225,0 230,0
Part No.
B+S
* * * * * * *
Busak+ Shamban
91
Busak+ Shamban
92
R WYNSEAL ZURCON
- Double Acting - Rubber Energised Plastic Face Seal - High Static and Dynamic Sealing Effect - Material - ZurconR Polyurethane + NBR Edition November 2003
Busak+ Shamban
93
Busak+ Shamban
94
ZurconR Wynseal
ZurconR Wynseal
Description Wynseal is a double-acting seal consisting The of a special polyurethane seal ring and an O-Ring as energizing element (Figure 35). The particular characteristic of the seal is the special design of the seal edge profile. Two external seal edges act as primary seal for pressures from both sides and prevent any build-up of hydrodynamic pressure over the seal profile and the risk of the blow-by effect. The central back-up and sealing bulge increases the sealing effect*. Grooves are provided on both sides on the plane surfaces to provide activation of the energizing O-Ring. These ensure direct pressure loading of the seal under all operating conditions. Since the installation groove is identical to that for the TurconR Glyd RingR, the seal is ideal for the standardisation of cylinder construction if, efficient and low cost seal elements are demanded in large quantities and, the cylinder can be adapted to meet different operating conditions. It has to be taken into consideration that in this case the gap dimension has to be checked ! ZurconR Application Examples The ZurconR Wynseal is the recommended sealing element for double acting pistons of hydraulic components in various sectors such as: S S S S Machine tools Forklifts & handling machinery Agriculture Industrial hydraulic light to medium duty Up to 25 MPa Up to 40 MPa Up to 0.5 m/s -35C to +110C Mineral oil-based hydraulic fluids (Z20N) (Z05N/WUAGN)
Important Note: The above data are maximum values and cannot be used at the same time. e.g. the maximum operating speed depends on material type, pressure, temperature and gap value. Temperature range also dependent on medium. Materials Standard Materials: H B+S references: Wynseal: O-Ring: Set reference: ZurconR Z20, 93 Shore A (on request 96 Shore A: reference Z05) NBR 70 Shore A Z20N/Z05N
Figure 35 ZurconR Wynseal Advantages - High static and dynamic sealing effect - High abrasion resistance - Simple groove design, one-piece piston possible - Suitable for grooves to ISO 7425, Part 1. *Only from PW42 and the following Series No.; PW40 and PW41 without sealing and supporting bulge.
H Sealing Parts references: Sealing ring: O-Ring: Set reference: Polyurethane 96 Shore A NBR 70 Shore A WUAGN
Busak+ Shamban
95
ZurconR Wynseal
Installation Recommendation
Ordering example Wynseal for ISO groove Cylinder diameter: Series No. Part No. B+S seal ring material code: O-Ring material code: Set code: Order No. Series No. Type (Standard)
Sealing Parts seal ring material code: O-Ring material code: Set code: Order No. Series No. Type (Standard)
PW43 0
PW43 0 0630
Cylinder diameter x 10 Quality Index (Standard) Material code (Seal ring) Material code (O-Ring)
Cylinder diameter x 10 Quality Index (Standard) Material code (Seal ring) Material code (O-Ring) Sealing Parts Ref. No.: GPS 63 47.5 6.3
Busak+ Shamban
96
ZurconR Wynseal
* B+S mold available, same ref. as Part No. The sizes printed in bold type are suitable for grooves to ISO 7425/1. The listed products are technically equivalent but availability and pricing may vary. Imperial (inch) sizes can be supplied.
Busak+ Shamban
97
ZurconR Wynseal
Bore o e Diameter i DN H9 74.0 75.0 75.0 76.2 80.0 80.0 82.55 85.0 88.9 90.0 95.0 100.0 101.6 105.0 110.0 115.0 115.0 118.0 120.0 125.0 125.0 127.0 130.0 130.0 135.0 135.0 140.0 145.0 150.0 152.4 160.0 170.0 177.8 180.0 185.0 190.0 200.0 203.2 210.0 220.0 230.0 240.0 250.0 300.0
G oo e Groove Diameter i d1 h9 58.5 64.0 59.5 65.2 69.0 64.5 67.05 69.5 73.4 74.5 79.5 84.5 86.1 89.5 94.5 99.5 94.0 102.5 104.5 109.5 104.0 111.5 114.5 109.0 119.5 114.0 119.0 124.0 129.0 131.4 139.0 149.0 156.8 159.0 164.0 169.0 179.0 182.2 189.0 199.0 209.0 219.0 229.0 279.0
G oo e Groove Width id h L1 +0.2 6.3 4.2 6.3 4.2 4.2 6.3 6.3 6.3 6.3 6.3 6.3 6.3 6.3 6.3 6.3 6.3 8.1 6.3 6.3 6.3 8.1 6.3 6.3 8.1 6.3 8.1 8.1 8.1 8.1 8.1 8.1 8.1 8.1 8.1 8.1 8.1 8.1 8.1 8.1 8.1 8.1 8.1 8.1 8.1
Part No. a o.
Sealing Parts Material code WUAGN GPS 75 64 4.2 GPS 75 59.5 6.3 GPS 80 69 4.2 GPS 80 64.5 6.3 GPS 85 69.5 6.3 GPS 90 74.5 6.3 GPS 100 84.5 6.3 GPS 105 89.5 6.3
PW4300740 PW4200750 PW4300750 PW420B231 PW4200800 PW4300800 PW430B335 PW4300850 PW430B337 PW4300900 PW4300950 PW4301000 PW430B341 PW4301050 PW4301100 PW4301150 PW4401150 PW4301180 PW4301200 PW4301250 PW4401250 PW430B349 PW4301300 PW4401300 PW4301350 PW4401350 PW4401400 PW4401450 PW4401500 PW440B431 PW4401600 PW4401700 PW440B438 PW4401800 PW4401850 PW4401900 PW4402000 PW440B442 PW4402100 PW4402200 PW4402300 PW4402400 PW4402500 PW4403000
* * * * * * * * * * * * * * * * * * * * * * * * * * * * * * * * * * * * * * * * * * * GPS 250 229 8.1 GPS 200 179 8.1 GPS 180 159 8.1 GPS 160 139 8.1 GPS 170 149 8.1 GPS 150 129 8.1 GPS 140 119 8.1 GPS 130 114.5 6.3 GPS 120 104.5 6.3 GPS 125 109.5 6.3 GPS 110 94.5 6.3
* B+S mold available, same ref. as Part No. The sizes printed in bold type are suitable for grooves to ISO 7425/1. The listed products are technically equivalent but availability and pricing may vary. Imperial (inch) sizes can be supplied.
Busak+ Shamban
98
R PHD/P POLYPAC
- Double Acting - Heavy Duty, High Pressure - Excellent Leakage Control - Material - ZurconR Polyurethane, NBR Elastomer + POM Edition November 2003
Busak+ Shamban
99
Busak+ Shamban
100
PHD/P Seal
Description The PHD/P Seal is a high-pressure heavy-duty piston seal with excellent leakage control and superior extrusion and wear resistance The PHD/P seal is a combination of a ZurconR polyurethane slipper seal energised by an elastomer profile ring and completed with two Back-up rings (POM). It is manufactured with a predefined interference fit, which together with the squeeze of the elastomer part ensures a good sealing effect even at low system pressure. At higher pressures the elastomer part is energised by the system pressure and consequently activates the slipper seal in the radial direction. The Back-up rings prevent the slipper seal from extrusion and ensure a long service life even under harsh conditions. Application Examples The PHD/P Seal is the recommended sealing element for double acting pistons of hydraulic cylinders working in very harsh conditions such as: S Excavators S Heavy duty cylinders Technical Data Operating conditions pressure: Up to 40 MPa Peak pressure up to 60 MPa Speed: Temperature: Media: Clearance: Up to 0.5 m/s -35C to +110C Mineral oil based hydraulic fluids The maximum permissible radial clearance Smax is shown in Table XLII, as a function of the operating pressure and functional diameter.
Important Note: The above data are maximum values and cannot be used at the same time. e.g. the maximum operating speed depends on material type, pressure, temperature and gap value. Temperature range also dependent on medium. Materials Standard Application: For hydraulic components in mineral oils or medium with good lubricating performance.
Figure 37 PHD/P Seal Advantages - Simple groove design - Excellent sealing effect - Excellent wear resistance - Increased clearance possible - Long service life
Busak+ Shamban
101
Installation Recommendation
R max. 0.2 S
15d-20d
DN
d1
r1
L1
Busak+ Shamban
102
Bore Dia. DN H9 135.0 140.0 145.0 150.0 155.0 160.0 165.0 170.0 180.0
Groove Dia. d1 h9 112.0 117.0 122.0 127.0 132.0 137.0 142.0 147.0 157.0
Groove Width L1 +0.2 16.0 16.0 16.0 16.0 16.0 16.0 16.0 16.0 16.0
Inlet Chamfer C 6.5 6.5 6.5 6.5 6.5 6.5 6.5 6.5 6.5
Radius r1 0.6 0.6 0.6 0.6 0.6 0.6 0.6 0.6 0.6
Radial Clearance S
Part No
Polypac Ref. No PHD 135112P PHD 140117P PHD 145122P PHD 150127P PHD 155132P PHD 160137P PHD 165142P PHD 170147P PHD 180157P
PKP0P1350 For pressure up to 35 MPa 0.50 For pressure from 35 MPa up to 60 MPa p 0.30 0 30 PKP0P1400 PKP0P1450 PKP0P1500 PKP0P1550 PKP0P1600 PKP0P1650 PKP0P1700 PKP0P1800
Ordering Example PHD/P Seal, complete. Bore diameter: DN = 80.0 mm Part No. PKP0P0800 (from Table XLII) Material set-code: Z2053 Polypac Ref. No.: PHD 8065P
PKP0 P
0800 -
Z2053
Busak+ Shamban
103
Busak+ Shamban
104
- Double Acting - Combined Seal and Guide Element - Material - NBR, Polyester Elastomer + POM -
Busak+ Shamban
105
Busak+ Shamban
106
Compact Seal
Figure 40 D-A-S Compact Seal, Type B PolypacR DBM The DBM Compact seal profile is characterized by a concave-shaped Back-up ring that prevents the elastomer profile ring from deformation and/or extrusion. The Backup ring is centered on the outside by the guide ring.
Figure 39 D-A-S Compact Seal, Type A DAS Type B This type is characterized by a Z-shaped back-up ring which forms a chamber with the elastomer seal ring on the inside and is centered on the outside by the guide ring. For many piston diameters, the width of the guide ring (dimension L2) can be selected due to sideloads. Due to the larger groove depth, the profile of the seal ring is more rigid than that of Type A and requires higher installation forces.
Figure 41 DBM Compact Seal Advantages - Good sealing effect, also suitable for holding cylinders - Capable of installation in closed grooves for reduced machining costs - Economic sealing and guiding solution - Simple snap installation.
Busak+ Shamban
107
Compact Seal
Application Examples The Compact seals are the recommended sealing element for double acting pistons of hydraulic components such as: S S S S Machine tools Truck cranes Forklifts & handling machinery Agriculture equipment
Materials H The D-A-S Compact Seal is available in the following material combinations: Profile seal: Back-up Ring: Guide rings: Set ref.: NBR 70 Shore A Polyester elastomer POM NCRO
Technical Data Operating conditions pressure: Up to 35 MPa peak up to 40 MPa Speed: Temperature: Media: Up to 0.5 m/s -30C to +100C Mineral oil-based hydraulic fluids, flame retardant hydraulic fluids, HFA, HFB, HFC (< +40C)
H The DBM Compact Seal is available in the following material combination: Profile seal: Back-up Ring: Guide rings: Set reference: NBR 80 Shore A Polyester elastomer POM N8UO
Important Note: The above data are maximum values and cannot be used at the same time. e.g. the maximum operating speed depends on material type, pressure, temperature and gap value. Temperature range also dependent on medium.
Ordering Example Bore diameter: DN = 80.0 mm Groove diameter: d1 = 60.0 mm Groove width: L1 = 22.4 mm DAS Type B Order No. Series No. Execution code Bore diameter x 10 Quality Index (Standard) Material set-code Sealing Parts Ref. No.: DAS 8060 PCBO A 0800 NCRO Polypac DBM Order No. Series No. Execution code Bore diameter x 10 Quality Index (Standard) Material set-code Polypac Ref. No.: DBM 314236 PCBO A 0800 N8UO
Busak+ Shamban
108
Compact Seal
d1
d2
d3 L1 L2 L2
Order No. d3 h11 31.4 39.4 49.4 59.4 63.4 69.4 79.4 89.4 99.4 109.4 119.4 124.4 129.4 139.4 149.4 159.4 L2 +0 1 +0.1 3.2 3.2 4.2 4.2 4.2 4.2 5.2 5.2 5.2 5.2 5.2 7.2 7.2 7.2 7.2 7.2 r max 0.4 0.4 0.4 0.4 0.4 0.4 0.4 0.4 0.4 0.4 0.8 0.8 0.8 0.8 0.8 0.8 PCA200320-NCRO PCA400400-NCRO PCA200500-NCRO PCA200600-NCRO PCA300630-NCRO PCA200700-NCRO PCA200800-NCRO PCA200900-NCRO PCA201000-NCRO PCA201100-NCRO PCA101200-NCRO PCA201250-NCRO PCA201300-NCRO PCA301400-NCRO PCA301500-NCRO PCA301600-NCRO
L1 +0 2 +0,2 15.5 15.5 20.5 20.5 20.5 20.5 22.5 22.5 22.5 22.5 22.5 26.5 26.5 26.5 26.5 26.5
DAS 32 24 DAS 40 32 DAS 50 38 DAS 60 48 DAS 63 51 DAS 70 58 DAS 80 66 DAS 90 76 DAS 100 86 DAS 110 96 DAS 120 106 DAS 125 108 DAS 130 113 DAS 140 123 DAS 150 133 DAS 160 143
Busak+ Shamban
109
DN
Compact Seal
r D A S Type B
d1
d3 L1 L2 L2
Part No. r max a NCRO 0.40 0.40 0.40 0.40 0.40 0.40 0.40 0.40 0.40 0.40 0.40 0.40 0.40 0.40 0.40 0.40 0.40 0.40 0.40 0.40 0.40 PCB 0N0200 PCB 0N0220 PCB 0D0250 PCB 1N0250 PCB 1N0250 PCB 2N0250 PCB 0N0280 PCB 000300 PCB 0A0300 PCB 0B0320 PCB 1A0320 PCB 0B0350 PCB 1A0350 PCB 0A0400 PCB 1A0400 PCB 2D0400 PCB 2E0400 PCB 3A0400 PCB 0N0420 PCB 0N0450 PCB 1A0450 * * * * * * * * * * * * * DBM 177 114 DBM 157 118 DBM 137 098 DBM 157 094 DBM 157 102/M DBM 125 086 * * * * * * * DBM 118 066 DAS 30 21 DAS 32 22/1 DAS 32 22 DAS 35 25/1 DAS 35 25 DAS 40 24 DAS 40 26 DAS 40 30/1 DAS 40 30/2 DAS 40 30 DAS 42 28 DAS 45 29 DAS 45 31 DBM 098 059 B+S Ref. Polypac Ref. No. Material code N8UO NCRO DAS 2011 DAS 22 13 DAS 25 15/1 DAS 25 15/2 DAS 25 15 DAS 25 16 DAS 28 19 Sealing Parts Ref. No.
Type DBM
* B+S mold available, same ref. as Part No. The listed products are technically equivalent but availability and pricing may vary. The bore diameters in bold type comply with the recommendations of ISO 6547. Imperial (inch) sizes can be supplied.
d2
Busak+ Shamban
110
DN
Compact Seal
Bore Dia. DN H9 9 45.0 50.0 50.0 55.0 55.0 56.0 60.0 60.0 63.0 63.0 63.0 65.0 65.0 70.0 70.0 75.0 75.0 80.0 80.0 85.0 90.0 90.0 95.0 100.0 100.0 105.0 110.0 110.0 115.0 115.0 120.0 125.0 125.0 130.0 130.0 133.0 135.0 135.0 140.0 140.0 140.0 145.0 145.0 150.0 150.0 d 9 d1 h9 35.00 34.00 34.00 39.00 39.00 40.00 44.00 44.00 47.00 47.00 47.00 49.00 50.00 50.00 54.00 55.00 59.00 60.00 62.00 65.00 70.00 72.00 75.00 75.00 82.00 80.00 85.00 92.00 90.00 97.00 95.00 100.00 103.00 105.00 105.00 115.00 110.00 110.00 115.00 115.00 118.00 120.00 120.00 125.00 125.00 L1+0.2 0 16.40 18.40 20.50 18.40 20.50 20.50 18.40 20.50 18.40 19.40 20.50 20.50 18.40 22.40 20.50 22.40 20.50 22.40 22.50 22.40 22.40 22.50 22.40 22.40 22.50 22.40 22.40 22.50 22.40 22.50 22.40 25.40 26.50 25.40 25.40 22.40 25.40 25.40 25.40 25.40 26.50 25.40 25.40 25.40 25.40
Groove Dimensions d 9 d2 h9 40.40 45.40 46.00 50.36 51.00 52.00 55.40 56.00 58.40 58.40 59.00 61.00 60.40 64.20 66.00 69.20 71.00 74.15 76.00 79.15 84.15 86.00 89.15 93.15 96.00 98.10 103.10 106.00 108.10 111.00 113.10 118.10 121.00 122.60 123.10 125.60 127.60 128.10 132.60 133.00 136.00 137.60 138.30 142.60 143.00 d3 h11 43.50 48.50 49.00 53.50 54.00 55.00 58.50 59.00 61.50 61.50 62.00 64.00 63.50 68.30 69.00 73.30 74.00 78.30 79.00 83.30 88.30 89.00 93.30 98.00 99.00 103.00 108.00 109.00 113.00 114.00 118.10 123.00 124.00 127.50 128.00 130.50 132.50 133.00 137.50 138.00 139.00 142.50 142.95 147.50 148.00 L2 +0.1 0 6.35 6.35 3.10 6.35 3.10 3.10 6.35 3.10 6.35 6.35 3.10 3.10 6.35 6.35 3.10 6.35 3.10 6.35 3.60 6.35 6.35 3.60 6.35 6.35 3.60 6.35 6.35 3.60 6.35 3.60 6.35 6.35 5.10 9.50 6.35 9.52 9.50 6.35 9.50 6.35 5.10 9.50 6.35 9.50 6.35 r max a
Part No.
Polypac Ref. No. Material code N8UO DBM 177137 DBM 196 133 DBM 196 133/M DBM 216 153
Sealing Parts Ref. No. NCRO DAS 45 35 DAS 50 34 DAS 50 34/1 DAS 55 39 DAS 5539/1 DAS 56 40
0.40 0.40 0.40 0.40 0.40 0.40 0.40 0.40 0.40 0.40 0.40 0.40 0.40 0.40 0.40 0.40 0.40 0.40 0.40 0.40 0.40 0.40 0.40 0.40 0.40 0.40 0.40 0.40 0.40 0.40 0.80 0.80 0.80 0.80 0.80 0.80 0.80 0.80 0.80 0.80 0.80 0.80 0.80 0.80 0.80
PCB 2N0450 PCB 1A0500 PCB 0B0500 PCB 1A0550 PCB 0B0550 PCB 0A0560 PCB 1A0600 PCB 0B0600 PCB 1A0630 PCB 2C0630 PCB 0B0630 PCB 0N0650 PCB 1A0650 PCB 0A0700 PCB 1N0700 PCB 0A0750 PCB 1A0750 PCB 0A0800 PCB 1A0800 PCB 0A0850 PCB 0A0900 PCB 1A0900 PCB 0A0950 PCB 0A1000 PCB 1A1000 PCB 0A1050 PCB 0A1100 PCB 1A1100 PCB 0A1150 PCB 1N1150 PCB 0A1200 PCB 0A1250 PCB 1A1250 PCB 1A1300 PCB 0B1300 PCB 001330 PCB 1A1350 PCB 0B1350 PCB 1A1400 PCB 0B1400 PCB 2A1400 PCB 1A1450 PCB 0B1450 PCB 1A1500 PCB0B1500
* * * * * * * * * * * * * * * * * * * * * * * * * * * * * * * * * * *
DBM 236 173 DBM 236 173/M DBM 248 185 DBM 248 185/M DBM 255 192/M DBM 255 196 DBM 275 196 DBM 275 212/M DBM 295 216 DBM 314 236 DBM 314 244/M DBM 334 255 DBM 354 275 DBM 374 295 DBM 393 295 DBM 393 332/M DBM 413 314 DBM 433 334 DBM 452 354 DBM 472 374 DBM 492 393 DBM 492 405/M DBM 511 413 DBM 523 452
DAS 60 44 DAS 60 44/1 DAS 63 47 DAS 63 47/2 DAS 63 47/1 DAS 65 49 DAS 65 50 DAS 70 50 DAS 70 54 DAS 75 55 DAS 75 59 DAS 80 60 DAS 80 62 DAS 85 65 DAS 90 70 DAS 90 72 DAS 95 75 DAS 100 75 DAS 100 82 DAS 105 80 DAS 110 85 DAS 110 92 DAS 115 90 DAS 115 97 DAS 120 95 DAS 125 100 DAS 125 103 DAS 130 105 DAS 130 105/1
* * * * * * * * *
DBM 531 433 DBM 551 452 DBM 551 464/M DBM 570 472 DBM 590 492
DAS 135 110 DAS 135 110/1 DAS 140 115 DAS 140 115/1 DAS 140 118 DAS 145 120 DAS 145 120/1 DAS 150 125 DAS 150 125/1
* B+S mold available, same ref. as Part No. Imperial (inch) sizes can be supplied.
The listed products are technically equivalent but availability and pricing may vary.
Busak+ Shamban
111
Compact Seal
Bore Dia. DN H9 9 150.0 152.4 155.0 155.0 160.0 160.0 160.0 160.0 165.0 170.0 170.0 175.0 180.0 180.0 185.0 190.0 195.0 200.0 200.0 210.0 220.0 220.0 230.0 240.0 250.0 250.0 d 9 d1 h9 128.00 127.00 130.00 130.00 130.00 130.00 135.00 138.00 140.00 145.00 148.00 150.00 150.00 155.00 160.00 165.00 170.00 175.00 175.00 185.00 190.00 195.00 205.00 215.00 220.00 225.00 L1+0.2 0 26.50 31.75 25.40 25.40 25.40 25.40 25.40 26.50 25.40 25.40 26.50 25.40 35.40 25.40 25.40 25.40 25.40 25.40 31.50 25.40 35.40 25.40 25.40 25.40 35.40 25.40
Groove Dimensions d 9 d2 h9 146.00 145.00 147.60 148.00 153.00 152.60 152.60 156.00 157.60 161.70 166.00 166.70 172.95 171.70 176.70 181.70 186.70 191.60 196.00 201.60 212.70 211.60 221.60 231.60 242.90 241.60 d3 h11 149.00 149.91 152.50 153.00 157.50 157.50 157.50 159.00 162.50 167.10 169.00 172.10 177.87 177.10 182.10 187.00 192.00 197.00 199.00 207.00 217.90 217.00 227.00 237.00 247.85 247.00 L2 +0.1 0 5.10 9.50 9.50 6.35 6.35 9.50 9.50 5.10 9.50 12.70 5.10 12.70 6.35 12.70 12.70 12.70 12.70 12.70 6.60 12.70 6.35 12.70 12.70 12.70 6.35 12.70 r max a
Part No.
0.80 0.80 0.80 0.80 0.80 0.80 0.80 0.80 0.80 0.80 0.80 0.80 0.80 0.80 0.80 0.80 0.80 0.80 0.80 0.80 0.80 0.80 0.80 0.80 0.80 0.80
PCB 2A1500 PCB 001524 PCB 0A1550 PCB 1B1550 PCB 0A1600 PCB 1A1600 PCB 1A1600 PCB 2A1600 PCB 0A1650 PCB 0A1700 PCB 1A1700 PCB 0A1750 PCB 0A1800 PCB 1A1800 PCB 0A1850 PCB 0A1900 PCB 0A1950 PCB 0A2000 PCB 102000 PCB 0A2100 PCB 0A2200 PCB 1A2200 PCB 0A2300 PCB 0A2400 PCB 0A2500 PCB 1A2500
* * * * * * * * * * * * * * * * * * * * * * * * DBM 984 886 DBM 866 767 DBM 905 807 DBM 944 846 DBM 708 610 DBM 728 629 DBM 748 649 DBM 767 669 DBM 787 688 DBM 787 688/M DBM 826 728 DBM 688 590 DBM 649 551 DBM 669 570 DBM 629 511 DBM 629 531 DBM 610511
DAS 155 130 DAS 155 130/1 DAS 160 130 DAS 160 130/1 DAS 160 135 DAS 160 138 DAS 165 140 DAS 170 145 DAS 170 148 DAS 175 150 DAS 180 150 DAS 180 155 DAS 185 160 DAS 190 165 DAS 195 170 DAS 200 175 DAS 210 185 DAS 220 190 DAS 220 195 DAS 230 205 DAS 240 215 DAS 250 220 DAS 250 225
* B+S mold available, same ref. as Part No. Imperial (inch) sizes can be supplied.
The listed products are technically equivalent but availability and pricing may vary.
Busak+ Shamban
112
- Double Acting - Combined Seal and Guide Element - Material - ZurconR Polyurethane, NBR + POM -
Busak+ Shamban
113
Busak+ Shamban
114
Seal ring
Important Note: The above data are maximum values and cannot be used at the same time. e.g. the maximum operating speed depends on material type, pressure, temperature and gap value. Temperature range also dependent on medium. Materials H The Polyurethane Compact seals PU DAS and EUD are available in the following composition: Sealing ring: Energiser: ZurconR Polyurethane NBR 70 Shore A 78 Shore A POM Z2052 93 Shore A
Busak+ Shamban
115
d3
d5 L5 L1 L5
Piston Dia. L5+0.1 2.60 2.60 3.10 3.10 3.10 3.10 3.10 3.10 3.10 3.60 3.60 3.60 3.60 5.10 5.10 5.10 5.10 5.10 5.10 5.10 6.60 6.35 6.35 r max. 0.4 0.4 0.4 0.4 0.4 0.4 0.4 0.4 0.4 0.4 0.4 0.4 0.4 0.8 0.8 0.8 0.8 0.8 0.8 0.8 0.8 0.8 0.8 d5 h11 38.50 44.00 49.00 54.00 59.00 62.00 64.00 69.00 74.00 79.00 89.00 99.00 109.00 124.00 139.00 149.00 159.00 164.00 169.00 179.00 199.00 248.00 267.00
PCC000400 - Z2052 PCC000450 - Z2052 PCC000500 - Z2052 PCC000550 - Z2052 PCC000600 - Z2052 PCC000630 - Z2052 PCC000650 - Z2052 PCC000700 - Z2052 PCC000750 - Z2052 PCC000800 - Z2052 PCC000900 - Z2052 PCC001000 - Z2052 PCC001100 - Z2052 PCC001250 - Z2052 PCC001400 - Z2052 PCC001500 - Z2052 PCC001600 - Z2052 PCC001650 - Z2052 PCC001700 - Z2052 PCC001800 - Z2052 PCC002000 - Z2052 PCC002500 - Z2052 PCC002700 - Z2052
Busak+ Shamban
116
DN
d4
d3
d5 L5 L1 L5
Piston Dia. L5+0.1 4.2 4.2 4.2 4.2 4.2 4.2 4.2 4.2 4.2 5.2 5.2 5.2 5.2 5.2 5.2 7.2 7.2 7.2 r max. 0.2 0.2 0.2 0.2 0.2 0.2 0.2 0.2 0.2 0.2 0.2 0.2 0.2 0.2 0.2 0.4 0.4 0.4 d5 h11 39.40 49.40 49.40 54.40 59.40 62.40 64.40 64.40 69.40 79.40 84.40 89.40 99.40 109.40 119.40 124.40 139.40 159.40 PCG000400-Z2052 PCG000500-Z2052 PCG100500-Z2052 PCG000550-Z2052 PCG000600-Z2052 PCG000630-Z2052 PCG000650-Z2052 PCG100650-Z2052 PCG000700-Z2052 PCG000800-Z2052 PCG000850-Z2052 PCG000900-Z2052 PCG001000-Z2052 PCG001100-Z2052 PCG001200-Z2052 PCG001250-Z2052 PCG001400-Z2052 PCG001600-Z2052 EUD4032/1 EUD5038 EUD5040/1 EUD5543 EUD6048 EUD6351 EUD6553 EUD6555/1 EUD7058 EUD8066 EUD8571 EUD9076 EUD10086 EUD11096 EUD120106 EUD125108 EUD140123 EUD160143 Order No. Polypac Ref. No.
d4
Busak+ Shamban
117
DN
Busak+ Shamban
118
- Double Acting - Combined Seal and Guide Element - Material - Rubber Fabric Reinforced NBR and POM -
Busak+ Shamban
119
Busak+ Shamban
120
Compact Seal
DUOPAC rubber fabric reinforced compact seals Type DPS and DPC
Description The compact seals DUOPAC DPS and DPC types are double acting piston seals with integrated guide rings. DUOPAC has been designed to optimize the advantages of the materials selection: S Fabric reinforcement with high mechanical strength, optimum thermal stability and lubricating properties is incorporated in the sealing element all over the dynamic contact area. For the DUOPAC DPC the reinforcement is extended on both sides to improve the extrusion resistance S Nitrile based elastomer with optimum elasticity and low compression set provides the initial radial pre-load S Acetal resin with improved form stability gives the Guide/backup rings high distortion and extrusion resistance Type DPS The DPS profile has been designed for its installation in closed grooves. The radial dimension of the profile has been reduced to the minimum to allow the necessary deformation during installation in closed grooves. Consequently its use must be limited to pressures up to 35 MPa. Seal ring reinforced Guide ring Seal ring NBR Figure 49 Compact Seal, Type DPC Advantages - DPS can be installed into closed grooves but its use must consequently be limited to medium duty applications - DPC are usually installed in open grooves in Heavy Duty applications (pressure peak up to 80MPa) - Improved abrasion resistance - Excellent sealing effect in combination with good dynamic and static friction behavior Application Examples The Compact seals are the recommended Sealing element for double acting Pistons of hydraulic components in following applications: Figure 48 Compact Seal, Type DPS S S S S Mining cylinders Presses Steel mills equipment Water hydraulic cylinders Type DPC The DPC profile is much more robust and can therefore be used for pressure level up to 70 MPa. An open groove is necessary. Seal ring reinforced Guide ring Seal ring NBR
Busak+ Shamban
121
Compact Seal
Technical Data Operating conditions: For an optimum performance of the DUOPAC, the recommended tolerances and surface finish must be applied. Pressure: Up to 35MPa DPS type Up to 70MPa DPC type Up to 0.5 m/s -30C to +130C Mineral oil based hydraulic fluids, water/oil and water/glycol emulsions.
Materials H The compact seals DUOPAC are available in the following material composition: Sealing element: Guide/Back-up Rings: Material set-code: Rubber fabric reinforced NBR POM N00OC
Important Note: The above data are maximum values and cannot be used at the same time. e.g. the maximum operating speed depends on material type, pressure, temperature and gap value. Temperature range also dependent on medium.
Ordering Example Compact Seal Type DPS Bore diameter: DN = 80 mm Groove diameter: d1 = 66 mm Groove width: L1 = 22.5 mm Part No.: PCE100800 (from Table XLVII)
Ordering Example Compact Seal Type DPC Bore diameter: DN = 80 mm Groove diameter: d1 = 60 mm Groove width: L1 = 22.4 mm Part No.: PCF000800 (from Table XLVIII)
Material set-code: N00OC Order No. Series No. Type (Standard) Bore diameter x 10 Quality Index (Standard) Material set-code Polypac Ref. No.: DPS 8066 PCE1 0 0800 N00OC
Material set-code: N00OC Order No. Series No. Type (Standard) Bore diameter x 10 Quality Index (Standard) Material set-code Polypac Ref. No.: DPC 8060 PCF0 0 0800 N00OC
Busak+ Shamban
122
Compact Seal
r=0,2
d2
d1
The bore diameters in bold type comply with the recommendations of ISO 6547.
Busak+ Shamban
123
DN
Compact Seal
Bore Dia. DN H11 100.0 110.0 120.0 125.0 125.0 140.0 140.0 150.0 160.0 160.0 180.0 200.0 200.0 220.0 250.0 d1 h9 86.0 96.0 106.0 105.0 108.0 120.0 123.0 133.0 140.0 143.0 163.0 170.0 180.0 200.0 230.0 L1 +0.2 22.5 22.5 22.5 25.0 26.5 25.0 26.5 26.5 25.0 26.5 26.5 36.0 31.5 31.5 31.5
Groove Dimensions L2+0.1 5.2 5.2 5.2 6.3 7.2 6.3 7.2 7.2 6.3 7.2 7.2 12.5 9.2 9.2 9.2 d2 h9 96.0 106.0 116.0 120.0 121.0 135.0 136.0 146.0 155.0 156.0 176.0 192.0 196.0 216.0 246.0 d3 h11 99.4 109.4 119.4 123.0 124.4 138.0 139.4 149.4 158.0 159.4 179.4 197.0 199.4 219.4 249.4
Order No.
Polypac Ref. No. DPS 10086 DPS 11096 DPS 120106 DPS 125105/1 DPS 125108 DPS 140120/1 DPS 140123 DPS 150133 DPS 160140/1 DPS 160143 DPS 180163 DPS 200170/1 DPS 200180 DPS 220200 DPS 250230
PCE101000-N00OC PCE001100-N00OC PCE001200-N00OC PCE001250-N00OC PCE101250-N00OC PCE001400-N00OC PCE101400-N00OC PCE001500-N00OC PCE001600-N00OC PCE101600-N00OC PCE001800-N00OC PCE002000-N00OC PCE102000-N00OC PCE002200-N00OC PCE002500-N00OC
The bore diameters in bold type comply with the recommendations of ISO 6547.
Busak+ Shamban
124
Compact Seal
d1
d2
L2
L2
Busak+ Shamban
125
DN
L1
d3
Compact Seal
Busak+ Shamban
126
R POLYPAC
- VEEPAC CH/G1
- Single Acting - Chevron Ring - With Support and Pressure Energising Ring - Material - POM, PTFE, Fabric Reinforced Rubber Edition November 2003
Busak+ Shamban
127
Busak+ Shamban
128
POLYPACR - Veepac
Veepac CH/G1
Description Veepac G1 is a set of fabric reinforced rings comprising one support ring, one sealing ring and a pressure energizing ring. It is a single acting piston seal. The support ring or base ring is manufactured out of nitrile elastomer with high Shore A hardness and reinforced with impregnated cotton fabric layers for an optimal extrusion resistance. The intermediate ring - the sealing ring - is a fabric reinforced nitrile elastomer with good resilience characteristics enabling the radial deflection under pressure load. Consequently the optimum sealing force is applied to the bore to be sealed. The energiser or spreader ring is made of POM or PTFE. Its function is to ensure a uniform pre-load of the seal. In some specific applications the energiser ring is made out of Acetal resin or Phenolic resin. Please contact our local B+S company for further details. Technical Data Operating conditions: Pressure: Up to 40 MPa Velocity: Up to 0.5 m/s Temperature:-30_C to +200_C, depending on material Media: Mineral oil, water glycol, water emulsions Important Note: The above data are maximum values and cannot be used at the same time. e.g. the maximum operating speed depends on material type, pressure, temperature and gap value. Temperature range also dependent on medium. Materials The following material can be delivered:
Material Set Code N0O0C V0P0C V0P0A Temperature Sealing Ring Material Energiser/ Spreader Ring Material POM PTFE PTFE
Support ring
Cotton reinforced NBR Cotton reinforced FKM Aramidic fiber reinforced FKM
Ordering Example For sealing element Veepac CH/G1 comprising 1 base ring and 1Chevron element in cotton fabric reinforced NBR and the Spreader ring in POM. Bore diameter: Part No. from table XLIX: Material set-code from material table above: Order No. Series Execution Mark Bore diameter x 10 Quality Index (Standard) Material code Poypac Ref. No.: CH 314236 G1 PC H0 G DN = 80.0 mm PCH0G0800 N0O0C 0800 N0O0C
Figure 52 Veepac CH/G1 Advantages - Exceptional wear resistance - Pre-load adjustment capability - Excellent behavior in harsh conditions Application Examples The Veepac seal is recommended for single acting or double acting (back to back installation) pistons in following applications: S S S S Mining equipment Excavator cylinders Steel mill cylinders Presses
Busak+ Shamban
129
POLYPACR - Veepac
d1
DN
Busak+ Shamban
130
d2
R POLYPAC
- SELEMASTER DSM
- Double Acting - Compact Piston Seal - Material - NBR + Fibre Reinforced NBR + POM -
Busak+ Shamban
131
Busak+ Shamban
132
Selemaster DSM
Description The piston seal DSM range has been designed to meet the needs of hydraulic equipments operating at high pressures and subjected to severe loading and vibration conditions. The main sealing element is manufactured in a highly compression set resistant nitrile. The most important quality of this element is the design of the multiple sealing lips for maximum sealing efficiency and end face configuration, which ensures that the selemaster can tolerate vibrations and severe misalignment. The two support rings are made in cotton fabric reinforced nitrile elastomer; the U shape is energised when pressure is applied. The last elements are the two guide rings manufactured in acetal resin which have also the function of anti-extrusion rings. Technical Data Operating conditions Pressure: Up to 70 MPa Velocity: Up to 0.5 m/s Temperature:-40_C to +130_C Media: Hydraulic fluids Mineral oil-based hydraulic fluids, water and water/ glycol emulsions Groove type:Open Important Note: The above data are maximum values and cannot be used at the same time. e.g. the maximum operating speed depends on material type, pressure, temperature and gap value. Temperature range also dependent on medium. Standard Material 1) Sealing element 2) Support ring 3) Guide ring Ordering Example Selemaster DSM Bore diameter: Groove diameter: Groove width Part No.(from table L): Material code: Polypac Ref.: Figure 54 Selemaster design 1) Sealing element 2) Support ring 3) Guide ring Advantages - Effective sealing during vibration and shock loading - High sealing efficiency - Extrusion resistance at high pressure Application Examples S Earth-moving machines S Excavators S Lift platforms Order No. Series No. Type (Standard) Bore diameter x 10 Quality Index (see table) Material Set-code PCL DN = 70.0 mm d = 50.0 mm E = 35.0 mm PCL000700 N8CO DSM 275196/1A 0 00700 N8CO NBR 80 Cotton reinforced NBR POM
3 2
Busak+ Shamban
133
Installation Recommendation
L1
L1
d1
Diameter Diameter d2 +/-0.07 42.80 47.80 52.80 57.80 60.80 61.30 62.80 67.50 72.50 77.50 77.50 82.50 87.80 87.80 89.60 92.80 92.50 97.50 99.10 102.50 107.30 107.50 111.60 112.30 ^ ^ ^ ^ ^
DN
d1 +/-0.05 38.80 43.77 48.77 53.80 56.74 57.25 58.70 62.62 67.70 72.62 72.62 77.62 82.58 82.87 84.66 87.86 87.60 92.60 94.20 97.60 101.82 102.70 106.12 106.82
PCL000450 PCL000500 PCL000550 PCL000600 PCL000630 PCL000635 PCL000650 PCL000700 PCL000750 PCL000800 PCL100800 PCL000850 PCL000900 PCL100900 PCL000921 PCL000953 PCL000950 PCL001000 PCL001016 PCL001050 PCL001100 PCL101100 PCL001143 PCL001150
Busak+ Shamban
134
d2
Bore Dia. DN H11 120.00 120.00 125.00 127.00 130.00 130.00 135.00 139.70 140.00 140.00 145.00 150.00 152.40 160.00 165.00 170.00 177.80 180.00 185.00 190.00 200.00 210.00 220.00 230.00 240.00 250.00 260.00 270.00 280.00 290.00 300.00 360.00
Groove Dia. d h11 95.00 100.00 100.00 101.60 105.00 110.00 110.00 114.30 115.00 120.00 120.00 125.00 127.00 135.00 135.00 140.00 152.40 155.00 160.00 165.00 175.00 185.00 195.00 205.00 215.00 225.00 235.00 245.00 255.00 265.00 275.00 335.00
Groove Width L +0.2 45.00 35.00 45.00 44.45 45.00 35.00 45.00 44.45 45.00 35.00 45.00 45.00 44.45 45.00 45.00 45.00 44.45 45.00 45.00 45.00 45.00 45.00 45.00 45.00 45.00 45.00 45.00 45.00 45.00 45.00 45.00 44.50 L1 +0.1 12.70 9.52 12.70 12.70 12.70 9.52 12.70 12.70 12.70 9.52 12.70 12.70 12.70 12.70 12.70 12.70 12.70 12.70 12.70 12.70 12.70 12.70 12.70 12.70 12.70 12.70 12.70 12.70 12.70 12.70 12.70 12.70
Diameter d1 +/-0.05 111.82 112.80 116.82 118.80 121.82 122.70 126.82 131.47 131.72 132.70 136.72 141.72 144.15 151.72 158.00 163.00 169.55 171.60 176.72 181.72 191.72 201.60 211.60 221.72 231.72 241.72 251.72 261.72 271.72 281.72 291.72 351.76
Diameter d2 +/-0.07 117.30 117.50 122.30 124.30 127.30 127.30 132.30 137.00 137.30 137.30 142.30 147.30 149.70 157.10 162.10 167.90 175.10 177.10 182.10 187.10 197.10 207.10 217.10 227.10 237.10 247.10 257.10 267.10 277.10 287.10 297.10 357.30 ^ ^
Part No.
Polypac Ref. No. DSM 472374/1A DSM 472393/1A DSM 492393/1A DSM 500400/1A DSM 511413/1A DSM 511433/1A DSM 531433/1A DSM 550450/1A DSM 551452/1A DSM 551472/1A DSM 570472/1A DSM 590492/1A DSM 600500/1A DSM 629531/1A DSM 649531/1A DSM 669551/1A DSM 700600/1A DSM 708610/1A DSM 728629/1A DSM 748649/1A DSM 787688/1A DSM 826728/1A DSM 866767/1A DSM 905807/1A DSM 944846/1A DSM 984886/1A DSM 1024925/1A DSM 1062965/1A DSM 11021004/1A DSM 11411043/1A DSM 11811082/1A DSM 14171318/1A
PCL001200 PCL101200 PCL001250 PCL001270 PCL001300 PCL101300 PCL001350 PCL001397 PCL001400 PCL101400 PCL001450 PCL001500 PCL001524 PCL001600 PCL001650 PCL001700 PCL001778 PCL001800 PCL001850 PCL001900 PCL002000 PCL002100 PCL002200 PCL002300 PCL002400 PCL002500 PCL002600 PCL002700 PCL002800 PCL002900 PCL003000 PCL003600
Busak+ Shamban
135
Busak+ Shamban
136
Busak+ Shamban
137
Busak+ Shamban
138
Sealing Parts RSE/W Single acting piston seal for dynamic applications. Installed in similar groove as B/NWO. The sealing element consist in a polyurethane U Cup and an L-shaped Back-up/guide ring.
Diameter Range mm 32 - 120 Pressure Range MPa Up to 25 Temperature Range _C -30 to +80 Velocity m/s Up to 0.5
Sealing Parts RSE/W/AR Sealing element identical to RSE/W with an additional retaining ring in front to allow easier installation.
Diameter Range mm 32 - 120 Pressure Range MPa Up to 25 Temperature Range _C -30 to +80 Velocity m/s Up to 0.5
PolypacR D11W Double acting piston seal for dynamic applications. Installed in open grooves. The NBR sealing element is supported at both sides by vulcanised cotton fabric reinforced rings with additional guide rings High sealing efficiency and high wear resistance.
Diameter Range mm 25 - 300 Pressure Range MPa Up to 50 Temperature Range _C -30 to +200 Velocity m/s Up to 0.5
PolypacR DS - DS/NEO Single acting piston U Ring for dynamic applications. Installed in open grooves. The U shaped sealing element is made out of cotton fabric reinforced NBR and provide with a NBR energiser ring and an additional POM back up ring can be integrated DS/NEO. High sealing efficiency and high wear resistance.
Diameter Range mm 25 - 300 Pressure Range MPa Up to 70 (DS/NEO) Temperature Range _C -30 to +130 Velocity m/s Up to 0.5
Busak+ Shamban
139
PolypacR URS - URFU Single acting piston U ring. installed in open grooves. The cotton reinforced NBR provides a high degree of stability and long service life.
Diameter Range mm 16 - 340 Pressure Range MPa Up to 40 Temperature Range _C -30 to +130 Velocity m/s Up to 0.5
PolypacR B/NWO Single acting piston seal for dynamic applications. Installed in open grooves. The nitrile sealing element is supported by a vulcanised cotton fabric reinforced ring with additional guide rings High sealing efficiency and high wear resistance.
Diameter Range mm 25 - 300 Pressure Range MPa Up to 50 Temperature Range _C -30 to +200 Velocity m/s Up to 0.5
PolypacR B/NWO - KR Same sealing element as B/NOW with an additional retaining ring in front to allow easier installation.
Diameter Range mm 25 - 300 Pressure Range MPa Up to 50 Temperature Range _C -30 to +200 Velocity m/s Up to 0.5
PolypacR B/NEO Single acting piston seal for dynamic applications. Installed in open grooves. The nitrile sealing element is supported by a vulcanised cotton fabric reinforced ring with additional anti-extrusion ring. High sealing efficiency and wear resistance.
Diameter Range mm 30 - 65 Pressure Range MPa Up to 40 Temperature Range _C -30 to +130 Velocity m/s Up to 0.5
Busak+ Shamban
140
TurconR VL SealTM Single acting O-Ring energised Piston Seal for dynamic applications. Installed in closed grooves. High seal efficiency and high flexibility also under adverse temperature and with radial displacement. Installed in standard O-Ring grooves.
Diameter Range mm 14 - 2700 Pressure Range MPa Up to 60 Temperature Range _C -45 to +200 Velocity m/s Up to 15
TurconR VarisealR W Single acting piston seal energised by a special helical spring. Its main advantage lies in its low friction and constant preloading force over a relatively large deformation range. The TurconR VarisealR W is used wherever friction has to be kept within a narrow tolerance zone.
Diameter Range mm 8 - 2700 Pressure Range MPa Up to 40 Temperature Range _C -70 to +260 Velocity m/s Up to 15
TurconR VarisealR M2 CR Single acting sealing element comprising a U-shaped TurconR ring and a Stainless Steel energising V spring. Low friction with no Stick-slip, minimal break out force and high wear resistance. Resistant to most liquids and chemicals. Unlimited shelf life. With integrated back up rings in material ZurconR Z43 for higher pressures or larger gaps.
Diameter Range mm 8 - 300 Pressure Range MPa Up to 100 Temperature Range _C -45 to +260 Velocity m/s Up to 5
TurconR Glyd RingR CR Double acting O Ring energised Piston Seal for dynamic applications. Installed in closed grooves including grooves to ISO 7425 as piston TurconR Glyd RingR. Low friction with no Stick-slip, minimal break out force and high wear resistance with integrated back up rings for higher pressures or larger gaps.
Diameter Range mm 8 - 2700 Pressure Range MPa Up to 100 Temperature Range _C -45 to +200 Velocity m/s Up to 5
Important Note: In the case of unpressurized applications in temperatures below 0C please contact our application engineers for assistance !
Busak+ Shamban
141
TurconR Glyd RingR Hz Double acting O Ring energised Piston Seal for dynamic applications. Special design on the sealing based on two face to face StepsealR profiles. The seal width is close to groove width to avoid axial movements. The Glyd RingR Hz is particularly dedicated to short strokes and high frequency applications. Installed in grooves according to ISO 7425 as piston TurconR Glyd RingR.
Diameter Range mm 8 - 2700 Pressure Range MPa Up to 40 Temperature Range _C -45 to +200 Velocity m/s Up to 15
Captive TurconR Glyd RingR For special applications where the Glyd RingR has to slide across dimensional changes (e.g. go from a small diameter with sealing efficiency over the seal to a larger diameter with no sealing efficiency or vice versa). In such applications Standard Glyd RingR would be pressed out of the groove.
Diameter Range mm 8 - 2700 Pressure Range MPa Up to 60 Temperature Range _C -45 to +200 Velocity m/s Up to 15
TurconR StepsealR CR Single acting O-Ring energised Piston Seal for dynamic applications. Installed in closed grooves including grooves acc. ISO 7425. High sealing efficiency, low friction with no Stick-slip, minimal break out force and high wear resistance. With integrated Back-up rings for higher pressures or larger gaps.
Diameter Range mm 8 - 2700 Pressure Range MPa Up to 100 Temperature Range _C -45 to +200 Velocity m/s Up to 5
Important Note: In the case of unpressurized applications in temperatures below 0C please contact our application engineers for assistance !
Busak+ Shamban
142