Location via proxy:   [ UP ]  
[Report a bug]   [Manage cookies]                
Scribd Logo
Upload

Welcome to Scribd!

  • 50 views

    H1AC1 Installation Guide

    Uploaded by

    Will
    The document provides installation instructions for a 3-6kW storage system inverter in 3 steps or less: [1] Mount the inverter bracket to the wall and attach the inverter. [2] Connect the PV panels, battery, AC wiring, communications cables, and grounding wire according to the provided diagrams and specifications. [3] Power on the inverter following the provided startup procedure and power it off using the provided shutdown procedure.

    Copyright:

    © All Rights Reserved
    Download as PDF, TXT or read online from Scribd

    H1AC1 Installation Guide

    Uploaded by

    Will
    50 views12 pages
    The document provides installation instructions for a 3-6kW storage system inverter in 3 steps or less: [1] Mount the inverter bracket to the wall and attach the inverter. [2] Connect the PV panels, battery, AC wiring, communications cables, and grounding wire according to the provided diagrams and specifications. [3] Power on the inverter following the provided startup procedure and power it off using the provided shutdown procedure.

    Original Title

    H1AC1-Installation-guide

    Copyright

    © © All Rights Reserved

    Available Formats

    PDF, TXT or read online from Scribd

    Did you find this document useful?

    Is this content inappropriate?

    The document provides installation instructions for a 3-6kW storage system inverter in 3 steps or less: [1] Mount the inverter bracket to the wall and attach the inverter. [2] Connect the PV panels, battery, AC wiring, communications cables, and grounding wire according to the provided diagrams and specifications. [3] Power on the inverter following the provided startup procedure and power it off using the provided shutdown procedure.

    Copyright:

    © All Rights Reserved
    Download as PDF, TXT or read online from Scribd
    Download as pdf or txt
    50 views12 pages

    H1AC1 Installation Guide

    Uploaded by

    Will
    The document provides installation instructions for a 3-6kW storage system inverter in 3 steps or less: [1] Mount the inverter bracket to the wall and attach the inverter. [2] Connect the PV panels, battery, AC wiring, communications cables, and grounding wire according to the provided diagrams and specifications. [3] Power on the inverter following the provided startup procedure and power it off using the provided shutdown procedure.

    Copyright:

    © All Rights Reserved
    Download as PDF, TXT or read online from Scribd
    Download as pdf or txt
    of 12

    Quick Installation Guide 3-6kW Storage System Inverter

    Packing List

    A B C D E

    F G H I J

    K L M N O

    P
    Object Quantity Description Object Quantity Description
    A 1 Inverter I 1 Earth terminal
    B 1 Bracket J 1 Communication connector
    PV connectors (for Hybrid only)
    C 4 K 1 Product manual
    (2*positive, 2*negative)
    PV pin contacts (for Hybrid only)
    D 4 L 1 Quick installation guide
    (2*positive, 2*negative)
    E 2 AC connectors M 1 CT (with 10m cable)
    Battery connectors
    F 2 N 1 WiFi/LAN/GPRS (Optional)
    (1*positive, 1*negative)
    Battery pin contacts
    G 2 O 1 Meter (Optional)
    (1*positive, 1*negative)
    H 5 Expansion tubes& Expansion screws P 1 CT extension connector

    1
    Inverter Installation

    Please make sure the inverter will be installed with a proper distance
    as shown below.

    Position Min Size


    Left 30cm
    Right 30cm
    Top 30cm
    Bottom 30cm
    Front 30cm

    Step 1: Fix the bracket on the wall

    Choose the place you want to install


    the inverter. Place the bracket on the
    wall and mark the position of the 5
    holes from bracket.

    Drill holes with electric drill, make


    sure the holes are at least 50mm
    deep, and then tighten the expansion
    tubes.

    2
    Insert the expansion tubes into the holes and tighten them. Install the
    bracket with the expansion screws.

    Step 2: Match the inverter with wall bracket


    Hang the inverter over the bracket, slightly lower the inverter, and make
    sure the two mounting bars on the back are properly fixed with the two
    bracket grooves.

    3
    Serial Port Connections

    Communication interface between the inverter and


    Meter/Battery/DRM/485 are as follows with Rj45 connectors which should
    be inserted corresponding port in the inverter.

    PIN
    1 2 3 4 5 6 7 8
    Port
    CT/
    Meter Meter
    Meter/ 485B 485A CT2+ CT2- CT1- CT1+
    485A 485B
    485
    BMS- BMS- BMS- BMS-
    BMS / GND / /
    485B CANL CANH 485A
    DRM DRM DRM DRM
    DRM GND GND DRM0 +3.3V
    4/8 3/7 2/6 1/5

    Note:
    CT1: For Hybrid/AC, CT2: Grid tied inverter (if have).
    Compatible Meter type: DDSU666 (CHINT), SDM230 (EASTRON).

    4
    Wiring Steps

    PV Wiring (For Hybrid Only)


    · Choose 12 AWG wire to connect the PV module.
    · Trim 6mm of insulation from the wire end.

    · Separate the DC connector (PV) as below.


    Plug Pin contact cable nut

    · Insert striped cable into pin contact and ensure all conductor strands
    are captured in the pin contact.

    · Crimp pin contact by using a crimping plier. Put the pin


    contact with striped cable into the corresponding
    crimping pliers and crimp the contact.
    ➢
    · Insert pin contact through the cable nut to assemble into back of the
    male or female plug. When you feel or hear a “click” the pin contact
    assembly is seated correctly.

    5
    · Unlock the DC connector:

    - Use the specified wrench tool.


    - When separating the DC+ connector, push the tool down from the
    top.
    - When separating the DC- connector, push the tool down from the
    bottom.
    - Separate the connectors by hand.

    Battery Wring
    · Turn off the DC switch.
    · Choose 10 AWG wire to connect the battery.
    · Trim 6mm of insulation from the wire end.

    10AWG

    · Separate the DC connector (battery) as below.


    Plug Pin contact cable nut

    · Insert striped cable into pin contact and ensure all conductor strands
    are captured in the pin contact.

    6
    · Crimp pin contact by using a crimping plier. Put the pin
    contact with striped cable into the corresponding
    crimping pliers and crimp the contact.

    ·➢ Insert pin contact through the cable nut to assemble into back of the
    male or female plug. When you feel or hear a “click” the pin contact
    assembly is seated correctly.

    · Unlock the DC connector


    - Use the specified wrench tool.
    - When separating the DC + connector, push the tool down from the
    top.
    - When separating the DC - connector, push the tool down from the
    bottom.
    - Separate the connectors by hand.

    Grid Wiring

    Cable dimensions
    Model (kW) 3.0 3.7 4.6 5.0 6.0

    Cable (AC) 8.0mm² 8.0mm² 8.0mm² 8.0mm² 10.0mm²


    Cable (BACK-UP) 4.0mm² 4.0mm² 6.0mm² 6.0mm² 6.0mm²
    Micro-Breaker 50A 50A 63A 63A 63A

    7
    - Trim all the wires to 52.5mm and the PE wire to 55mm.
    - Use the crimping pliers to trim 12mm of insulation from all wire ends
    as shown in the picture.

    L: Brown/Red Wire
    N: Blue/Black Wire
    PE: Yellow & Green Wire

    Note: Please refer to local cable type and color for actual installation.

    A. BACK-UP Wiring

    · Separate the BACK-UP plug into three parts as below.


    1. Hold the middle part of the female insert, rotate the back shell to
    loosen it, and detach it from female inset.
    2. Remove the cable nut (with rubber insert) from the back shell.

    · Slide the cable nut and then the


    back shell onto the cable.

    · Push the threaded sleeve into the


    socket, tighten up the cap on the
    terminal.

    8
    · Push the threaded sleeve to connection terminal until both are locked
    tightly on the inverter.

    · Loosen the cap on the terminal, pull the threaded sleeve out of the
    socket.

    B. AC Wiring
    · Separate the AC plug into three parts as below.
    1. Hold the middle part of the female insert, rotate the back shell to
    loosen it, and detach it from female inset.
    2. Remove the cable nut (with rubber insert) from the back shell.

    · Slide the cable nut and then the back shell


    onto the cable.

    9
    · Push the threaded sleeve into the socket,
    tighten up the cap on the terminal.

    · Push the threaded sleeve to connection terminal until both are locked
    tightly on the inverter.

    · Remove the AC connector: Press the bayonet out


    of the slot with a small screwdriver or the unlock
    tool and pull it out, or unscrew the threaded
    sleeve, then pull it out.

    Grounding Wiring
    Use the crimping pliers to press the ground cable into the ground terminal,
    screw the ground screw with screwdriver as shown below.

    10
    BMS Connection
    Step 1: Prepare a standard network cable and cable connector, then insert
    the network cable through the cable connector.

    Step 2: Crimp the cable with a Rj45 plug which is inside of the cable
    connector.

    Step 3: Insert the cable connector into BMS port at the bottom of inverter.

    11
    Inverter Start-Up

    Please refer to the following steps to start up the inverter.


    1. Ensure the inverter fixed well on the wall.
    2. Make sure all the AC wirings are completed.
    3. Make sure the meter is connected well.
    4. Make sure the battery is connected well.
    5. Make sure the external EPS contactor is connected well (if needed).
    6. Turn on the PV/DC switch (for Hybrid only), AC breaker, EPS breaker and
    battery breaker.
    7. Enter the settings page, select START / STOP and set it to start.
    Note:
    · When starting the inverter for the first time, the country code will be set
    by default to the local settings. Check if the country code is correct.
    · Set the time on the inverter using the button or by using the APP.

    Inverter Switch Off

    Please refer to the following steps to switch off the inverter.


    1. Enter the settings page, select START / STOP and set it to stop.
    2. Turn off the PV/DC switch (for Hybrid only), AC breaker, EPS breaker and
    battery breaker.
    3. Wait 5 min before you open the upper lid (if in need of repair).

    12

    You might also like