GSM Telephone
GSM Telephone
GSM Telephone
GT-E2130
1. Safety Precautions
2. Specification
3. Product Function
8. PCB Diagrams
This Service Manual is a property of Samsung Electronics Co.,Ltd. ⓒ Samsung Electronics Co.,Ltd.
Any unauthorized use of Manual can be punished under applicable
International and/or domestic law. 2009. 09. Rev.1.0
2. Specification
M S P ow er 33 dBm ~ 5d Bm 30 dBm ~ 0d Bm
4 1
Power Cl ass
(max +33dBm) (max +30dBm)
T DM A M u x 8 8
2-1
TX Power TX Power
GSM900 DCS1800
control level control level
15 0±5 dBm
2-2
Main Function
- GPRS, Dual Band(GSM 900/1800, 850/1900 Mhz)
- 1.77” TFT QQVGA, 262K
- VGA Camera & Video Recording
- MP3 Player with microSD(Up to 2GB)
- FM intenna with Recording
- Bluetooth 2.0
- Phone book 1000 EA (x3 entries)
- WAP 2.0, Embedded Java Games
- 40 Poly ringtone (Mp3,Midi)
- Java Games, Native Game
- 1000mAh standard Battery
- Mobile Tracker 2.0
- Mobile Prayer 2.0
- Fake call
- Bike mode
- SOS Message
3-1
SAMSUNG Proprietary-Contents may change without notice
This Document can not be used without Samsung's authorization
10. Reference data
Reference Abbreviate
10-1
― Be careful to use a kind of magnetic object or tool, because performance of parts is damaged by
the influence of magnetic force.
― Surely use a standard screwdriver when you disassemble this product, otherwise screw will be
worn away.
― Repair after separate Test Pack and Set because for short danger (for example an overcurrent
and furious flames of parts etc) when you repair board in condition of connecting Test Pack and
tuning on.
― Take specially care of soldering, because Land of PCB is small and weak in heat.
― Surely tune on/off while using AC power plug, because a repair of battery charger is dangerous
when tuning ON/OFF PBA and Connector after disassembling charger.
― Don't use as you pleases after change other material than replacement registered on SEC System.
Otherwise engineer in charge isn't charged with problem that you don't keep this rules.
1-1
SAMSUNG Proprietary-Contents may change without notice
This Document can not be used without Samsung's authorization
Safety Precautions
Several semiconductor may be damaged easily by static electricity. Such parts are called by ESD
(Electrostatically Sensitive Devices), for example IC,BGA chip etc. Read Precaution below.
You can prevent from ESD damage by static electricity.
― Remove static electricity remained your body before you touch semiconductor or parts with
semiconductor. There are ways that you touch an earthed place or wear static electricity prevention
string on wrist.
― Use soldering removing tool to break static electricity. Otherwise ESD will be damaged by static
electricity.
― Don't unpack until you set up ESD on product. Because most of ESD are packed by box and
aluminum plate to have conductive power,they are prevented from static electricity.
― You must maintain electric contact between ESD and place due to be set up until ESD is
connected completely to the proper place or a circuit board.
1-2
SAMSUNG Proprietary-Contents may change without notice
This Document can not be used without Samsung's authorization
4. Array course control
4-1
4-2
4-3
3. Press the "Start" button and connect the Handset, then press "확인".
4-4
6. When downloading is complete, automatically the small window was showed up.
4-5
5-1
5-2
6-2
6-3
6-4
6-5
6-6
6-7
Please consult the GSPN website (Samsung Portal) for the most recent version of the product's part list.
6-8
9-1. Power On
Yes
Not OK
Check battery voltage
is higher than 3.3V Change battery
OK
Check VPERM_3.0V,
VANA_2.85V, VRF_2.85V, Not OK
VSIM_3.0V, VMEM_1.8V, Check the UCP200
VGPIO_2.8V of UCP200
OK
Not OK
Check the pin 1 of
OSC201 produces clock Solder OSC201 again
signal
OK
OK
No
Is Power On working? Repeat sequence
Yes
END
9-1
9-2
R309
C326
C3 2 9 R3 1 0
C315
C3 1 3 SC1 0 8
C321
U3 0 2
TP_WEn
R30 8
C32 4
U303
R3 0 5 TP4 0 6
C2 2 0 C2 1 7 C2 0 6 C2 2 1 C3 0 7
C5 0 1
R306
C318
C311
R303
C4 2 5
C32 0
C3 0 5
C322
R307
R301
C3 1 9 U5 0 0
C219
R3 1 3
C3 1 7 C3 2 8
R508
U3 0 1 U3 0 0
R3 1 1 R5 0 6
L400
R3 1 4 R3 1 5 C5 0 0
R200
SC106
UME200
OSC201
R312
C222
C3 0 0 C3 0 8
C407
C205
C310
C309
U400
ZD300 ZD303
C331
R428
TP403
L3 0 3
C330
U5 0 1 TP4 0 7
TP201
L3 0 2
TP200
MIC300
R3 0 2
SC104
C304
C302
R405
Q400
C5 0 2
C3 0 6
C224
R300
R2 0 9
R4 1 3 TP4 0 4
TH 2 0 0 C2 0 2
C303
C301
R210
C229
C230
C504
C5 0 3
R414
R2 0 7 TA 3 0 0
C108
C110
C113
C116
C402
C406
R416
R415
C415
U1 0 0
TP408
C1 0 1
L2 0 1
R507
C1 0 0 R4 2 3
C1 2 4 C2 2 8
C2 1 4
SPI_INT
SPI _ DI
R4 2 2
U103
U4 0 3 C2 1 2 C2 1 0
F101
C1 3 6 C1 1 1 C4 2 3
L103
C2 1 1
C213
C2 0 8
L1 0 5 C1 0 9 C2 0 7
UCP200
R4 2 4
C1 0 7
DD101 DU101
TP405
R4 2 5 C4 2 4
D CL1 0 1
C112
9-3
R2 1 3
SC109 L2 0 2
ON_PMU
FS C1 0 1
U200
BT _ R ST 1 0 1
SPI _ CLK OSC2 0 0
R203 C2 0 9 C2 0 0
C2 0 3 L2 0 0
D200
C201
R409
SC103
SPI_DO
C216
C2 1 5
SPI _ CS L1 0 2 L1 0 4 C2 0 4 R2 1 2 R2 0 6 L2 0 3
C119
C115
C123
C120
TP_ TMS SC1 0 5
SC1 0 7
ANT105
TP_ TRS T_ N
R1 1 6 F1 0 0
C133
R118
R117
C118
TP_ TD I
TP_RTCK
C121
R112
L109
RFS100
TP_GND
TP_TDO
C129
R1 0 3
SC102
L110
L1 0 8
L1 1 1
C128
L113
C125
TP_ TCK
PAM1 0 0 C1 2 6
R1 0 4
TP_RSTON
C122
C1 1 7
SC1 1 0
SC1 0 1
ANT1 0 3
C1 3 7
Flow Chart of Troubleshooting
Yes
Yes
END
9-4
BOTHHOLE203
ZD501
Z D5 0 2
SD500
Z D1 0 6 L1 0 1
R403
R404
C411
C412
C1 0 2
L401
L402
L403
L404
L405
L3 0 5
U1 0 4
C1 4 0 L3 0 4
ZD401
R1 1 9 C4 1 3
ZD3 0 5
L1 0 6
C414
L1 0 0
R4 0 6
C5 1 1
C1 3 1 R4 0 7
U102
C1 0 6 R4 0 2 R4 2 7
C1 3 2
U1 0 1 R4 0 8
301
C4 0 0 R4 0 0
F500
R1 0 9
R111
C134
C4 0 4 C4 0 3
R1 1 0 C1 3 0 Z D4 0 0
SPK
C4 1 0 C4 0 1
C4 0 8 C4 0 5
F501
R411
R410
R4 0 1 C4 0 9
TP400
TP401
R4 1 2 R4 1 7
C1 0 4 R1 0 5
HD C4 0 0 C1 0 3 R1 0 2
C422
9-5
ZD307
ZD306
L406
C416
U401
BTC500
R4 2 1 C4 1 7
U402
C419
R4 2 0 R5 1 3
SPK300
SIM500
C509
Z D3 0 2
C4 1 8
D500
L3 0 0 Q5 0 0
C4 2 0
C510
L3 0 1
R5 1 2
Z D3 0 1
MOT500
D201
R426
C506
R511
C505
C5 0 7
BOTHHOLE202
D4 0 0
Flow Chart of Troubleshooting
Yes
Not OK
Check the connection
of MIC Solder MIC again
OK
OK
Not OK
Check the circuit Solder L302, L303, ZD300 and ZD303
of MIC PART again.
OK
No
Is Phone MIC working? Replace MIC
Yes
END
9-6
R309
C326
C3 2 9 R3 1 0
C315
C3 1 3 SC1 0 8
R304
C321
U3 0 2
R211
C218
C5 0 1
R306
C318
C311
R303
C4 2 5
C32 0
C322
R307
R301
C3 1 9 U5 0 0
C219
R3 1 3
C3 1 7 C3 2 8
R508
U3 0 1 U3 0 0
R3 1 1 R5 0 6
L400
R3 1 4 R3 1 5 C5 0 0
R200
SC106
UME200
OSC201
R312
C222
C3 0 0 C3 0 8
C407
C205
C310
C309
U400
ZD300 ZD303
C331
R428
TP403
L3 0 3
C330
U5 0 1 TP4 0 7
TP201
L3 0 2
TP200
MIC300
R3 0 2
SC104
C304
C302
R405
Q400
C5 0 2
C3 0 6
C224
R300
R2 0 9
R4 1 3 TP4 0 4
TH 2 0 0 C2 0 2
C303
C301
R210
C229
C230
C504
C5 0 3
R414
R2 0 7 TA 3 0 0
C108
C110
C113
C116
C402
C406
R416
R415
C415
U1 0 0
TP408
C1 0 1
L2 0 1
R507
C1 0 0 R4 2 3
C1 2 4 C2 2 8
C2 1 4
SPI_INT
SPI _ DI
R4 2 2
U103
U4 0 3 C2 1 2 C2 1 0
F101
C1 3 6 C1 1 1 C4 2 3
L103
C2 1 1
C213
C2 0 8
L1 0 5 C1 0 9 C2 0 7
UCP200
R4 2 4
C1 0 7
DD101 DU101
TP405
R4 2 5 C4 2 4
D CL1 0 1
C112
R2 1 3
SC109
L2 0 2
ON_PMU
FS C1 0 1
9-7
U200
BT _ R ST 1 0 1
SPI _ CLK OSC2 0 0
C2 0 9 C2 0 0
R203
C2 0 3 L2 0 0
D200
C201
R409
SC103
SPI_DO
C216
C2 1 5
SPI _ CS L1 0 2 L1 0 4 C2 0 4 R2 1 2 R2 0 6 L2 0 3
C119
C115
C123
C120
TP_ TMS SC1 0 5
SC1 0 7
ANT105
TP_ TRS T_ N
R1 1 6 F1 0 0
C133
R118
R117
C118
TP_ TD I
TP_RTCK
C121
R112
L109
RFS100
TP_GND
TP_TDO
C129
R1 0 3
SC102
L110
L1 0 8
L1 1 1
C128
L113
C125
TP_ TCK
PAM1 0 0 C1 2 6
R1 0 4
TP_RSTON
C122
C1 1 7
SC1 1 0
SC1 0 1
ANT1 0 3
C1 3 7
Flow Chart of Troubleshooting
Yes
Not OK
Check the connection
of IFC400 Solder pin 3 of IFC400 again
OK
Not OK
Check MIC_BIAS.
( When UCP200 operates Solder R300, R302, C302, C304 and
and call is connected ) TA300 again
OK
Not OK
Check the circuit Solder L302, L303 again
of EAR MIC
OK
Yes
END
9-8
9-9
C3 2 9 R3 1 0
C315
C3 1 3 SC1 0 8
R304
C321
U3 0 2
R3 0 5 TP4 0 6
C2 2 0 C2 1 7 C2 0 6 C2 2 1 C3 0 7
R211
C218
C5 0 1
R306
C318
C311
R303
C4 2 5
C32 0
C3 0 5
C322
R307
R301
C3 1 9 U5 0 0
C219
R3 1 3
C3 1 7 C3 2 8
R508
U3 0 1 U3 0 0
R3 1 1 R5 0 6
L400
R3 1 4 R3 1 5 C5 0 0
R200
SC106
UME200
OSC201
R312
C222
C3 0 0 C3 0 8
C407
C205
C310
C309
U400
ZD300 ZD303
C331
R428
TP403
L3 0 3
C330
U5 0 1 TP4 0 7
TP201
L3 0 2
TP200
MIC300
R3 0 2
SC104
C304
C302
R405
Q400
C5 0 2
C3 0 6
C224
R300
R2 0 9
R4 1 3 TP4 0 4
TH 2 0 0 C2 0 2
C303
C301
R210
C229
C230
C504
C5 0 3
R414
R2 0 7 TA 3 0 0
C108
C110
C113
C116
C402
C406
R416
R415
C415
U1 0 0
TP408
C1 0 1
L2 0 1
R507
C1 0 0 R4 2 3
C1 2 4 C2 2 8
C2 1 4
SPI_INT
SPI _ D I
R4 2 2
U103
U4 0 3 C2 1 2 C2 1 0
F101
C1 3 6 C1 1 1 C4 2 3
L103
C2 1 1
C213
C2 0 8
C1 0 9
9-10
L1 0 5 C2 0 7
UCP200
R4 2 4
C1 0 7
DD101 DU101
TP405
R4 2 5 C4 2 4
DCL1 0 1
C112
R2 1 3
SC109
L2 0 2
ON_PMU
FSC1 0 1
U200
BT_ RST1 0 1
SPI _ CLK OSC2 0 0
C2 0 9 C2 0 0
R203
C2 0 3 L2 0 0
D200
C201
R409
SC103
SPI_DO
C216
C2 1 5
SPI _ CS L1 0 2 L1 0 4 C2 0 4 R2 1 2 R2 0 6 L2 0 3
C119
C115
C123
C120
TP_ TMS SC1 0 5
SC1 0 7
ANT105
T P_ TRST_ N
R1 1 6 F1 0 0
C133
R118
R117
C118
TP_ TD I
TP_RTCK
C121
R112
L109
RFS100
TP_GND
TP_TDO
C129
R1 0 3
SC102
L110
L1 0 8
L1 1 1
C128
L113
C125
TP_ TCK
PAM1 0 0 C1 2 6
R1 0 4
TP_RSTON
C122
C1 1 7
Flow Chart of Troubleshooting
SC1 1 0
SC1 0 1
A NT1 0 3
C1 3 7
Flow Chart of Troubleshooting
Yes
Not OK
Check the circuit Solder pin 5,6,7 of IFC400
of IFC400 , L402, L403 and L404 again
OK
Yes
END
9-11
9-12
Yes
Not OK
Check the U300
Pin #1, #2 = 5V? Replace U300
OK
Not OK
Check the C300, C305
and R301 Solder C300, C305 and R301.
OK
END
9-13
9-14
Yes
OK
OK
Not OK
END Replace the speaker
9-15
9-16
SC1 0 8
TP_WEn
TP4 0 6
I FC4 0 0 C2 2 0 C2 1 7 C2 0 6 C2 2 1 C3 0 7
R211
ZD501
ZD502
C218
C4 2 5 C5 0 1
C3 0 5
R301
C219
VK5 0 0
U3 0 0
R200
SC106
UME200
OSC201
R312
C222
R3 1 7
C3 0 0 C3 0 8
C205
R3 1 6
ZD300 ZD303
Z D3 0 4
C331
TP403
L3 0 3
C330
SD500
ZD10 6 L1 0 1
R403
C411
C412
R404
C1 0 2
L401
L402
L403
L404
L405
L3 0 5
U1 0 4
TP201
L3 0 2
R3 0 2
SC104
C304
C302
C1 4 0 L3 0 4
ZD401
R1 1 9 C4 1 3 C3 0 6
R300
C224
R2 0 9
ZD305
L1 0 6 L1 0 0
C414
R4 0 6 TH 2 0 0 C2 0 2
C303
C301
R210
C229
C230
C5 1 1
C1 3 1 R4 0 7
R414
R2 0 7 TA3 0 0
U102
C1 0 6 R4 0 2 R4 2 7
TP408
C1 3 2
U1 0 1 R4 0 8
301
C4 0 0 R4 0 0 L2 0 1
F500
R1 0 9 R4 2 3 C2 2 8
R111
C134
C4 0 4 C4 0 3 C2 1 4
R1 1 0 C1 3 0 Z D4 0 0
SPK
C4 1 0 C4 0 1 R4 2 2
U4 0 3 C2 1 2 C2 1 0
C4 0 8 C4 0 5 C4 2 3
F501
C2 1 1
C213
C2 0 8
R411
R410
R4 0 1 C4 0 9 C2 0 7
UCP200
R4 2 4
TP400
TP401
R4 1 2 R4 1 7
TP405
C1 0 4 R1 0 5 R4 2 5 C4 2 4
SC109
9-17
HD C4 0 0 C1 0 3 R1 0 2 L2 0 2
C422
ZD307
ZD306
OSC2 0 0
C2 0 9 C2 0 0
L406
C2 0 3 L2 0 0
C416
D200
C201
R409
SC103
C216
C2 1 5
U401
BTC500
R4 2 1 C4 1 7 L1 0 2 L1 0 4 C2 0 4 R2 1 2 R2 0 6 L2 0 3
U402
C419
C119
C115
C123
C120
R4 2 0 R5 1 3
SPK300
SC1 0 5
SIM500
SC1 0 7
C509
Z D3 0 2
C4 1 8
D500
L3 0 0 Q5 0 0 F1 0 0
R1 1 6
C133
R118
R117
C4 2 0
C118
C510
L3 0 1
C121
R5 1 2
Z D3 0 1
R112
L109
RFS100
C129
R1 0 3
SC102
L110
L1 0 8
L1 1 1
C128
L113
C125
PAM1 0 0 C1 2 6
R1 0 4
MOT500
C122
C1 1 7
D2 0 1
SC1 1 0
R426
C506
R511
C505
SC1 0 1
C5 0 7
D4 0 0
Flow Chart of Troubleshooting
Yes
No
When one of the keys is
pushed, Check the Dome sheet & Key FPCB
is it displayed on LCD?
Yes
No
When one of the keys is Replace the PBA
pushed,
KEY_IO signal is OK?
Yes
END
9-18
Yes
No
Is BACKLIGHT set AlwaysON Set BACKLIGHT on Always ON
in the Menu?
Yes
Not OK
Check the outflow voltage of Replace U402
U402(PIN 3) is equal to 3.7V
OK
Yes
END
9-19
ZD501
ZD50 2
SD500
Z D1 0 6 L1 0 1
R403
R404
C411
C412
C1 0 2
L401
L402
L403
L404
L405
L3 0 5
U1 0 4
C1 4 0 L3 0 4
ZD401
R1 1 9 C4 1 3
ZD30 5
L1 0 6
C414
L1 0 0
R4 0 6
C5 1 1
C1 3 1 R4 0 7
U102
C1 0 6 R4 0 2 R4 2 7
C1 3 2 R4 0 8
U1 0 1
301
C4 0 0 R4 0 0
F500
R1 0 9
R111
C134
C4 0 4 C4 0 3
R1 1 0 C1 3 0 ZD4 0 0
SPK
C4 1 0 C4 0 1
C4 0 8 C4 0 5
F501
R411
R410
R4 0 1 C4 0 9
TP400
TP401
R4 1 2 R4 1 7
C1 0 4 R1 0 5
9-20
HD C4 0 0 C1 0 3 R1 0 2
C422
ZD307
ZD306
L406
C416
U401
BTC500
R4 2 1 C4 1 7
U402
C419
R4 2 0 R5 1 3
SPK300
SIM500
C509
Z D3 0 2
C4 1 8
D500
L3 0 0 Q5 0 0
C4 2 0
C510
L3 0 1
R5 1 2
Z D3 0 1
MOT500
Flow Chart of Troubleshooting
D20 1
R426
C506
R511
C505
C5 0 7
BOTHHOLE202
D4 0 0
Flow Chart of Troubleshooting
Yes
No
Is BACKLIGHT set Always
Set BACKLIGHT on Always ON
ON in the Menu?
Yes
OK
Replace LED
Yes
END
9-21
UP
SOFT5 0 0
SOFT5 0 1
R5 0 5
R5 0 4
LED504 LED505
RI GHT
LEFT
INT
SEND
END
DOWN
ZD5 0 0
DIGIT500 DIGIT502
DIGIT501
R5 0 2
R5 0 3
LED 5 0 2
LED 5 0 3
DIGIT503 DIGIT505
DIGIT504
DIGIT506 DIGIT508
DIGIT507
R5 0 0
R5 0 1
LED 5 0 0
LED 5 0 1
STAR SHARP
DIGIT509
9-22
RX ON
RF INPUT=62CH
AMP=-50dBm
Yes
Yes
No
Check UCP200
pin G1, F1 (EGSMRX) Check C120, C123, and L104
≥-65dBm
Not ok
Yes
Re solder or Change
F100
Check UCP200 No
MOD_STANDBY=HIGH
Re solder or Change
PON_PA=LOW
BAND=LOW
UCP200
END
9-23
TX ON (5Level)
Yes
Yes
PAM100 pin4
≥ 0dBm
Yes
No
Check UCP200
Re solder UCP200
Yes
END
9-24
RX ON
RF INPUT=698CH
AMP=-50dBm
Yes
Yes
Check UCP200 No
pin E1, D1 (DCSRX) Check C115, C119 and L102
≥-65dBm
>
Not ok
Yes
Re solder or Change
F100
Check UCP200 No
MOD_STANDBY= "HIGH" Re solder or Change
PON_PA= "LOW"
BAND= "HIGH" UCP200
Yes
END
9-25
TX ON (0Level)
PAM100 Pin16
≥ 30dBm Re solder PAM100
PAM100 pin2
≥ 0dBm
END
9-26
9-27
C3 2 9 R3 1 0
C315
C3 1 3 SC1 0 8
R304
C321
U3 0 2
R3 0 5 TP4 0 6
C2 2 0 C2 1 7 C2 0 6 C2 2 1 R211 C3 0 7
C218
C5 0 1
R306
C318
C311
R303
C4 2 5
C32 0
C3 0 5
C322
R307
C3 1 9 U5 0 0 R301
C219
R3 1 3
C3 1 7 C3 2 8
R508
U3 0 1 U3 0 0
R3 1 1 R5 0 6
L400
R3 1 4 R3 1 5 C5 0 0
R200
SC106
UME200
OSC201
R312
C222
C3 0 0 C3 0 8
C407
C205
C310
C309
U400
ZD300 ZD303
C331
R428
TP403
L3 0 3
C330
U5 0 1 TP4 0 7
TP201
L3 0 2
TP200
MIC300
R3 0 2
SC104
C304
C302
R405
Q400
C5 0 2
C3 0 6
C224
R300
R2 0 9
R4 1 3 TP4 0 4
TH 2 0 0 C2 0 2
C303
C301
R210
C229
C230
C504
C5 0 3
R414
R2 0 7 TA 3 0 0
C108
C110
C113
C116
C402
C406
R416
R415
C415
U1 0 0
TP408
C1 0 1
L2 0 1
R507
C1 0 0 R4 2 3
C1 2 4 C2 2 8
C2 1 4
SPI_INT
SPI _ DI
R4 2 2
U103
U4 0 3 C2 1 2 C2 1 0
F101
C1 3 6 C1 1 1 C4 2 3
L103
C2 1 1
C213
C2 0 8
9-28
L1 0 5 C1 0 9 C2 0 7
UCP200
R4 2 4
C1 0 7
DD101 DU101
TP405
R4 2 5 C4 2 4
D CL1 0 1
C112
R2 1 3
SC109
L2 0 2
ON_PMU
FS C1 0 1
U200
BT _ R ST1 0 1
SPI _ CLK OSC2 0 0
C2 0 9 C2 0 0
R203
C2 0 3 L2 0 0
D200
C201
R409
SC103
SPI_DO
C216
C2 1 5
SPI _ CS L1 0 2 L1 0 4 C2 0 4 R2 1 2 R2 0 6 L2 0 3
C119
C115
C123
C120
TP_ TMS SC1 0 5
SC1 0 7
ANT105
TP_ TRS T_ N
R1 1 6 F1 0 0
C133
R118
R117
C118
TP_ TD I
TP_RTCK
C121
R112
L109
RFS100
TP_GND
TP_TDO
C129
R1 0 3
SC102
L110
L1 0 8
L1 1 1
C128
L113
C125
TP_ TCK
PAM1 0 0 C1 2 6
R1 0 4
TP_RSTON
C122
C1 1 7
Flow Chart of Troubleshooting
SC1 1 0
SC1 0 1
ANT1 0 3
C1 3 7
Flow Chart of Troubleshooting
Yes
Not OK
Check the voltage at
Pin#16, #11, #10 of U101. Re solder of change U101
Is it OK?
OK
Not OK
Check the voltage at Pin
#4 of U104 Is it OK? Re solder of change U104
OK
Not OK
Check the voltage at Pin
#1, #4, #8 of U102 Is it Re solder of change U102
OK?
OK
Not OK
Is there any signals at the
Pin#13 and #14 of U101? Re solder of change U101
OK
Not OK
OK
9-29
9-30
PNX4902
GSM/GPRS Class 10 single chip
Keypad
32-bit ARM926EJ-STM control processor
SAIC/TTY/CTM
Integrated DCXO and AFC correction
Motor
I2C/UART/PCM/PWM RF Subsystem RF System
Bluetooth/FM support
SIM SIM card interface
Color LCD, up to176x220 pixels, 65K colors
Analog accessory detection Bluetooth
OVP Three clock outputs(32kHz.,26MHz,26/nMHz) (SPI)
Up to 42 GPIOs(1.8V/2.8V)
78MHz burst memory access
FM
Battery
PMU
Memory
IF Connector MIC
Audio Subsystem Ear MIC
(20 Pin)
SPK
Backend IC
EAR SPK
Camera LCD
SD Card
(VGA) 1.52" 128x128 CSTN
7-1
SAMSUNG Proprietary-Contents may change without notice
This Document can not be used without Samsung's authorization
SAMSUNG Proprietary-Contents may change without notice
This Document can not be used without Samsung's authorization
BOTHHOLE203
BOTHHOLE200
L1 0 7
R309
C326
C3 2 9 R3 1 0
C135
C315
C3 1 3 SC1 0 8
L1 1 2 I FC4 0 0
R304
C321
U3 0 2
ZD501
Z D5 0 2
TP_WEn
R30 8
C32 4
U303
R3 0 5 TP4 0 6
C2 2 0 C2 1 7 C2 0 6 C2 2 1 C3 0 7
R211
C218
C5 0 1
R306
C318
C311
R303
C4 2 5
C32 0
C3 0 5
C322
R307
R301
VK 5 0 0 C3 1 9 U5 0 0
C219
R3 1 3
C3 1 7 C3 2 8
R508
U3 0 1 U3 0 0
R3 1 1 R5 0 6
L400
R3 1 4 R3 1 5 C5 0 0
R200
SC106
R3 1 7
UME200
R3 1 6
OSC201
R312
C222
C3 0 0 C3 0 8
C407
C205
Z D 3 04
SD500
Z D1 0 6 L1 0 1
C310
C309
R403
C411
C412
R404
C1 0 2
L401
L402
L403
L404
L405
L3 0 5
U400
ZD300 ZD303
C331
U1 0 4
R428
TP403
L3 0 3
C330
C1 4 0 L3 0 4 U5 0 1 T P4 0 7
TP201
ZD401
L3 0 2
TP200
C4 1 3
MIC300
R1 1 9 R3 0 2
SC104
Z D3 0 5
C304
C302
R405
L1 0 6
Q400
L1 0 0
C414
C5 0 2
R4 0 6 C3 0 6
C224
R300
R2 0 9
C5 1 1
C1 3 1 R4 0 7 R4 1 3 TP4 0 4
TH 2 0 0 C2 0 2
U102
C303
C301
R210
R4 2 7
C229
C230
C1 0 6 R4 0 2
C1 3 2
U1 0 1 R4 0 8
C504
C5 0 3
301
R414
R2 0 7 TA3 0 0
C108
C110
C113
C116
C402
C406
R416
R415
C415
C4 0 0 R4 0 0 U1 0 0
F500
R1 0 9
TP408
C1 0 1
R111
C134
C4 0 4 C4 0 3 L2 0 1
C1 3 0 ZD40 0
R507
R1 1 0 C1 0 0
SPK
C4 1 0 C4 0 1 C1 2 4 R4 2 3 C2 2 8
C2 1 4
SPI_INT
SPI _ D I
C4 0 8 C4 0 5 R4 2 2
U103
F501
8-1
C2 1 2 C2 1 0
R411
R410
U4 0 3
F101
R4 0 1 C4 0 9 C1 3 6 C4 2 3
C1 1 1
L103
C2 1 1
R510
R509
C213
C2 0 8
TP400
TP401
R4 1 2 R4 1 7 C1 0 9
L1 0 5 C2 0 7
UCP200
C1 0 4 R1 0 5 R4 2 4
ANT101
C1 0 7
DD101 DU101
H D C4 0 0
TP405
C1 0 3 R1 0 2 D CL1 0 1
R4 2 5 C4 2 4
C112
C422
R2 1 3
SC109
L2 0 2
ON_PMU
ZD307
ZD306
FSC1 0 1
U200
OSC2 0 0
L406
BT_ RST1 0 1
SPI _ CL K
C2 0 9 C2 0 0
C416
R203
C2 0 3 L2 0 0
D200
C201
R409
SC103
SPI_DO
U401
BTC500
C216
R4 2 1 C4 1 7 C2 1 5
U402
C419
R4 2 0 R5 1 3 L1 0 2 L1 0 4
SPI _ CS
C2 0 4 R2 1 2 R2 0 6 L2 0 3
SPK300
SIM500
C509
C119
C115
C123
C120
Z D3 0 2 TP_ TMS S C1 0 5
C4 1 8
D500
SC1 0 7
ANT105
L3 0 0 Q5 0 0
C4 2 0 T P_ T RS T_ N
C510
L3 0 1
R1 1 6 F1 0 0
C133
R118
R117
C118
R5 1 2 TP_ TD I
Z D3 0 1
TP_RTCK
C121
R112
L109
RFS100
TP_GND
TP_TDO
C129
R1 0 3
SC102
L110
L1 0 8
MOT500
L1 1 1
C128
L113
C125
TP_ TCK
PA M1 0 0 C1 2 6
R1 0 4
TP_RSTON
C122
D2 0 1
C1 1 7
BOTHHOLE201
R426
C506
R511
C505
C5 0 7
BOTHHOLE202
D4 0 0
8. PCB Diagrams
SC1 1 0
SC1 0 1
AN T1 0 3
C1 3 7
Top
PCB Diagrams
Bottom
RCV3 0 0
LCD_PAD
UP
SOFT5 0 1
SOFT5 0 0
R5 0 5
R5 0 4
LED504 LED505
RI GHT
LEFT
INT
SEND
END
DOWN
Z D5 0 0
DIGIT500 DIGIT502
DIGIT501
R5 0 2
R5 0 3
LED5 0 2
LED5 0 3
DIGIT503 DIGIT505
DIGIT504
DIGIT506 DIGIT508
DIGIT507
R5 0 0
R5 0 1
LED5 0 0
LED5 0 1
STAR SHARP
DIGIT509
8-2
11-1. Disassembly
1 2
SCREW(4EA) Remove
1) Use a disassembly tool and disassemble REAR's hooker 1 place. 1) Lift and disassemble REAR.
※ Caution ※ Caution
1) Be careful not to make scratch and molding damage! 1) Be careful not to make scratch and molding damage!
11-1
5 6
2 1
11-2
9 10
1) Use a tool and pull out FOGO pin 1) Disassemble CAMERA using jig.
※ Caution ※ Caution
1) Be careful of scratch and cosmetic damage. 1) Be careful of socket damage
11 12
1) Raise using a decomposition tool from corner of 1) Separate LCD upper corner 2 places with PBA
shield can of picture and disjoint. using a decomposition tool and lift.
※ Caution ※ Caution
1) Be careful not to make scratch and molding 1) Be careful not to make scratch and molding
damage! damage!
11-3
11-2 Assembly
1 2
Check direction
1) Assemble screw 2 points after placing shield can. 1) Assemble camera to socket.
※ Caution ※ Caution
1) H/W parts be careful not to be damaged 1) H/W parts be careful not to be damaged
3 4
11-4
5 6
3 2
11-5
9 10
1) do not pull with picture and lay down and place 1) Insert Man-Machine Interface Conveyor at
SIDE KEY FPCB. confidential talk in outside with picture.
※ Caution ※ Caution
1) Pay attention to FPCB damage. 1) Pay attention to FPCB damage
11 12
1
2
Press and assemble hooker
to number Order place.
3 4
11-6
13
1
4
5 2
3 6
11-7