F
F
Design ideas in this guide use the following devices. A complete device list and corresponding data sheets for these products can be found at www.microchip.com/analog. Operational Amplifiers MCP6XX MCP6XXX MCP6V01/2/3 MCP6V06/7/8 Comparators MCP654X MCP656X Analog-to-Digital Converters MCP3421 MCP3422/3/4 MCP355X MCP3901 Temperature Sensors MCP9800 MCP9804 MCP9700/A MCP9701/A Voltage References MCP1525 MCP1541 Digital Potentiometers MCP40XX MCP40D1X MCP41XX MCP42XX MCP43XX MCP45XX MCP46XX MCP41XXX MCP42XXX Digital-to-Analog Converters MCP4725 MCP4728 MCP482X MCP492X
www.microchip.com/analog
The MCU controls the actuators and maintains the operation of the sensor signal conditioning circuits based on the condition of the signal detection. For the digital to analog feedback path, the digital-to-analog converter (DAC), digital potentiometer and Pulse-Width-Modulator (PWM) devices are most commonly used. The MOSFET driver is commonly used for the interface between the feedback circuit and actuators such as motors and valves. Microchip offers a large portfolio of devices for signal chain applications.
DAC/PWM
Sensor Overview
Many system applications require the measurement of a physical or electrical condition, or the presence or absence of a known physical, electrical or chemical quantity. Analog sensors are typically used to indicate the magnitude or change in the environmental condition, by reacting to the condition and generating a change in an electrical property as a result. Typical phenomena that are measured are: Electrical Signal and Properties Magnetic Signal and Properties Temperature Humidity Force, Weight, Torque and Pressure Motion and Vibration Flow Fluid Level and Volume Light and Infrared Chemistry/Gas There are sensors that respond to these phenomena by producing the following electrical properties: Voltage Current Resistance Capacitance Charge This electrical property is then conditioned by an analog circuit before being converted to a digital circuit. In this way, the environmental condition can be measured and the system can make decisions based on the result. The table below provides an overview of typical phenomena, the type of sensor commonly used to measure the phenomena and electrical output of the sensor. For additional information, please refer to Application Note AN990.
Sensor
Hall Effect Magneto-Resistive Thermocouple RTD Thermistor IC Infrared Thermopile Capacitive Infrared Strain Gauge Load Cell Piezo-electric Mechanical Transducer LVDT Piezo-electric Microphone Ultrasonic Accelerometer Magnetic Flowmeter Mass Flowmeter Ultrasound/Doppler Hot-wire Anemometer Mechanical Transducer (turbine) Ultrasound Mechanical Transducer Capacitor Switch Thermal Photodiode pH Electrode Solution Conductivity CO Sensor Photodiode (turbidity, colorimeter)
Electrical Output
Voltage Resistance Voltage Resistance Resistance Voltage Current Voltage Capacitance Current Resistance/Voltage Resistance Voltage or Charge Resistance, Voltage, Capacitance AC Voltage Voltage or Charge Voltage Voltage, Resistive, Current Voltage Voltage Resistance/Voltage Frequency Resistance Voltage Time Delay Resistance, Voltage Capacitance On/Off Voltage Current Voltage Resistance/Current Voltage or Charge Current
Flow
Light Chemical
Product Overviews
Operational Amplifiers (Op Amps)
Microchip Technology offers a broad portfolio of op amp families built on advanced CMOS technology. These families are offered in single, dual and quad configurations, which are available in space saving packages. These op amp families include devices with Quiescent Current (IQ) per amplifier between 0.6 A and 6 mA, with a Gain Bandwidth Product (GBWP) between 10 kHz and 60MHz, respectively. The op amp with lowest supply voltage (VDD) operates between 1.4V and 6.0V, while the op amp with highest VDD operates between 6.5V and 16.0V. These op amp families fall into the following categories: General Purpose, Low Offset, Auto-zeroed, High Speed, Low Noise and mCal (self calibrating input offset voltage (VOS)).
Comparators
The MCP6541 and MCP6561 family of comparators provide ultra low power, 600 nA typical, and higher speed with 40 ns propagation delay, respectively. The MCP6541 family low operating current is suitable for battery powered application and the output drive capability is ideal for alert buzzer driver applications. The MCP6561 family with greater than 4 MHz toggle frequency is ideal for higher speed embedded system applications where sinusoidal output from sensors to square wave conversion is needed. The 47ns typical propagation delay also makes this device ideal for microprocessor interface. Both families of comparators are available with single, dual and quad as well as with push-pull and open-drain output options (MCP6546 and MCP6566).
Voltage References
Microchip offers the MCP15XX family of low power and low dropout precision Voltage References. The family includes the MCP1525 with an output voltage of 2.5V and the MCP1541 with an output voltage of 4.096V. Microchips voltage references are offered in SOT23-3 and TO-92 packages.
Product Overviews
Digital Potentiometers
Microchips family of digital potentiometers offer a wide range of options. These devices support the 6-bit through 8-bit applications. Offering both volatile and non-volatile options, with digital interfaces from the simple Up/ Down interface to the standard SPI and I2C interfaces. These devices are offered in small packages such as 6-lead SC70 and 8-lead DFN for the single potentiometer devices, 14-lead TSSOP and 16-lead QFN packages for the dual potentiometer devices, and 20-lead TSSOP and QFN packages for the quad potentiometer devices. Non-volatile devices offer a Wiperlock Technology feature, while volatile devices will operate down to 1.8V. Resistances are offered from 2.1k to 100 k. Over 50 device configurations are currently available. The Digital Potentiometer Design Guide (Microchip Document No. 22017), shows various application examples of the digital potentiometer devices.
Local Sensors
Local Sensing
Local sensors are located relatively close to their signal conditioning circuits, and the noise environment is not severe; most of these sensors are single ended (not differential). Non-inverting amplifiers are a good choice for amplifying most of these sensors output because they have high input impedance, and require a minimal amount of discrete components.
100 nF U1 RINT R6.65 M IINT VSEN P2 CCG SR Latch C2 100 nF Comparator U2 VDD CSEN VCM
PIC16F690
P1
VINT
+
PH Monitor
MCP6XX, MCP6XXX
+
-
VOUT
P4 Timer1 P3
RCM1 20 k
MCP6291
VREF
+ RCM2 20 k
CCM 100 nF
Remote Sensors
Remote Sensing
All sensors in a high noise environment should be considered as remote sensors. Also, sensors not located on the same PCB as the signal conditioning circuitry are remote. Remote sensing applications typically use a differential amplifier or an instrumentation amplifier.
Products
High Precision Low Offset Op Amps Auto-zeroed Op Amps Low Noise Op Amps
Differential Amplier
VREF
EMI
Difference Amplifier
+
MCP6V02 MCP6V07 MCP617
VOUT
Signal Chain Design Guide
EMI
C4 R4
R8 R7
+
VDD R5
+
VDD
VDD/2 R6 C5
R1 = RTD C1
+
VDD A1 VOUT
MCP6541 MCP6561
R2 VDD R3 R4
VOUT
MCP6541 MCP6561
VDD/2
Attributes: Precision dual Element RTD Sensor Circuit Reliable Oscillation Startup Freq. (R1 x R2)1/2
Attributes: Low Cost Solution Single Comparator Circuit Square Wave Output Freq. = 1/ (1.386 x R1 x C1)
Wheatstone Bridge
Bridge Sensor Circuit
Sensors for temperature, pressure, load or other physical excitation quantities are most often configured in a Wheatstone bridge configuration. The bridge can have anywhere from one to all four elements reacting to the physical excitation, and should be used in a ratiometeric configuration when possible, with the system reference driving both the sensor and the ADC voltage reference. By using the same reference for both the sensor excitation and ADC, the variation in the reference can be cancelled out. Furthermore, the output voltage from the bridge sensor is proportional to the excitation voltage. Therefore, the ADC that is using the external reference is more popular than the ADC that is using internal reference, for the ratiometric configuration. One example sensor from GE NovaSensor is an absolute pressure sensor, shown below, a four element varying bridge. This example uses the MCP355X family of delta sigma ADCs. When designing with the MCP355X family of 22-bit delta-sigma ADCs, the initial step should be to evaluate the sensor performance and then determine what steps (if any) should be used to increase the overall system resolution when using the MCP355X. In many situations, the MCP355X devices can be used to directly digitize the sensor output, eliminating any need for external signal conditioning circuitry. Using the absolute pressure sensor as our Wheatstone bridge example, the NPP-301 device has a typical full scale output of 60 mV when excited with a 3V battery. The pressure range for this device is 100 kPa. The MCP3551 has a output noise specication of 2.5 VRMS. The following equation is a rst order approximation of the relationship between pressure in pascals (P) and altitude (h), in meters. log(P) 5
h 15500
Using 60 mV as the full scale range and 2.5 V as the resolution, the resulting resolution from direct digitization in meters is 0.64 meters or approximately 2 feet. It should be noted that this is only used as an example for discussion; temperature effects and the error from a rst order approximation must be included in nal system design.
Example of Wheatstone Bridge Sensor Configuration with High Resolution Delta-Sigma ADC
0.1 F 1.0 F To VDD NPP-301 2 R2 R1 R3 1 VREF 8 VDD SPI MCU 5, 6, 7
VIN+
R4 Altimeter Watch
Delta-Sigma ADCs
Voltage and Current Measurment Using Delta-Sigma ADCs
The MCP342X family devices are easy-to-use high precision delta sigma ADC devices from Microchip. These devices have an internal reference (2.048V) with a user programmable PGA (x1, x2, x4, x8). The ADC resolution is programmable as 12-bit, 14-bit, 16-bit or 18-bit by the user. This ADC family offers single, dual and four differential input channels. Because of its simplicity and low price, this device family can be used for various applications from simple voltage and current measurement to high precision temperature measurement.
MCP3422 Analog-to-Digital Converter (ADC) Feature Summary
Bit Resolution Number of Differential Input Channels Internal Programmable Gain Amplifier INL Error (Typical) Offset Error (Typical) Internal Reference Voltage Output Noise (Typical) Gain Error (Typical) Interface 18 bits (User can select 18-, 16-, 14- or 12-bit options) 2 x1, x2, x4 or x8 (user option) 10 PPM of full scale range 15 V 2.048V 1.5 Vrms 0.05% of full scale range I2C
MCU
MCU
________ R2 VIN = ( R1 + R2 ) (VBAT) (R1 + R2) 1 VMeasured = ADC Output Codes LSB _________ _____ R2 PGA Reference Voltage LSB = ________________ 2 N 1 Reference Voltage 2.048V LSB of 18-bit ADC = ________________ = ______ = 15.625 V 2 N 1 217
2.4 GHz
Heat
18-bit ADC +
MCP3421 MRF24J40
(Thermocouple)
MCU
PIC MCU
Current = (Measured Voltage)/(Known Resistance Value of Current Sensor) Direction of current is determined by sign bit (MSB bit) of the ADC output code.
10
Delta-Sigma ADCs
Temperature Measurements Using 4 Channel ADC (MCP3424) See Thermocouple Reference Design (TMPSNSRD-TCPL1)
Thermocouple Sensor Isothermal Block (Cold Junction) Isothermal Block (Cold Junction)
MCP9804
1
MCP9804
2 3 4 5 6 7
MCP9804
MCP9804
5 k
VDD
11
RTD Solution
Resistive Temperature Detectors (RTDs) are highly accurate and repeatable temperature sensing elements. When using these sensors a robust instrumentation circuit is required and it is typically used in high performance thermal management applications such as medical instrumentation. This solution uses a high performance Delta-Sigma Analogto-Digital converter, and two resistors to measure RTD resistance ratiometrically. A 0.1C accuracy and 0.01C measurement resolution can be achieved across the RTD temperature range of -200C to +800C with a single point calibration. This solution uses a common reference voltage to bias the RTD and the ADC which provides a ratio-metric relation between the ADC resolution and the RTD temperature resolution. Only one biasing resistor, RA, is needed to set the measurement resolution ratio (shown in equation below). RTD Resistance RRTD = RA
(2 n CodeCode) 1
Where: Code = ADC output code RA = Biasing resistor n = ADC number of bits (22 bits with sign, MCP3551) For instance, a 2V ADC reference voltage (VREF) results in a 1V/LSb (Least Signicant Bit) resolution. Setting RA= RB=6.8 k provides 111.6 V/C temperature coefcient (PT100 RTD with 0.385/C temperature coefcient). This provides 0.008C/LSb temperature measurement resolution for the entire range of 20 to 320 or -200C to +800C. A single point calibration with a 0.1% 100 resistor provides 0.1C accuracy as shown in the gure below. This approach provides a plug-and-play solution with minimum adjustment. However, the system accuracy depends on several factors such as the RTD type, biasing circuit tolerance and stability, error due to power dissipation or self-heat, and RTD non-linear characteristics.
Applications
Refrigeration equipment Power supply over temperature protection General purpose temperature monitoring
RTD Instrumentation Circuit Block Diagram and Output Performance (see Application Note AN1154)
VDD LDO C* C* VREF 1 F VDD PIC MCU 3 SPI VREF VLDO RB 5%
Measured Accuracy (C) 0.1 0.05 0 -0.05 -0.1 -200
RA 1% + RTD
MCP3551
600
800
12
Equation 1-1 shows how to calcultate the gain for the simplied circuit (Figure 1-1b). The gain is the ratio of the digital potentiometers wiper position on the RAB resistor ladder. As the wiper moves away from the midscale value, the gain will either become greater then one (as wiper moves towards Terminal A), or less then one (as wiper moves towards Terminal B). The devices wiper resistance (RW) is ignored for rst order calculations. This is due to it being in series with the op amp input resistance and the op amp input impedence is very large. Circuit Gain Equation VOUT = RBW x VIN RAW RBW = RAB x Wiper Code # of Resistors
CF
Op Amp(1)
VOUT
Op Amp(1)
+ VOUT +
13
For devices with an odd number of RS resistors have a midscale wiper value that is near unity gain. The MCP4261 is an example of a device that has an even number of RS resistors in the RAB string, while the MCP4011 is an example of a device that has an odd number of RS resistors in the RAB string. For devices with an odd number of RS resistors in the RAB string to be able to have an exact unity gain, the device would need to be used in the generic circuit conguration (Figure 1-1), and the components would need to be selected so R1 + RAW could equal R2 + RBW.
Generic Circuit(1, 2)
1.000000 1.007843 1.015748 1.023715 1.031746
Comment
Zero Scale
. . .
62 63 64 65 66
. . .
0.939394 0.969231 1.000000 1.031746 1.064516
. . .
1.639175 1.652850 1.666667 1.680628 1.694737
. . .
129
128
Mid Scale
. . .
124 125 126 127 128
. . .
31.000000 41.666667 63.000000 127.000000 Divide Error(3)
. . .
2.878788 2.908397 2.938462 2.968992 3.000000
. . .
Full Scale
Note 1: Gain = ( (RAB / # of Resistors) * Wiper Code ) /( ( (# of Resistors - Wiper Code) / # of Resistors) * RAB) 2: Uses R1 = R2 = 10 k. 3: Theoretical calculations. At full scale in the simplified circuit a divide by 0 error results.
14
selected, the internal 2.048 VREF would produce 1 mV of resolution. If a smaller output step size is desired, the output range would need to be reduced. So, using gain of 1 is a better choice than using gain of 2 conguration option for smaller step size, but its full-scale range is one half of that of the gain of 2. Using a voltage divider at the DAC output is another method for obtaining a smaller step size.
Comparator 1 R1 R2
0.1 F
Light
VDD
10 F
0.1 F
MCP4728
8 7 6
VDD
Quad DAC
R2
0.1 F
VOUT = VREF x Dn GX 4096 R2 VTRIP = VOUT x R1 + R2 Where Dn = Input Code (0 to 4095) GX = Gain Selection (x1 or x2)
Light
VDD
R1 R2
0.1 F
VTRIP4
RSENSE
To MCU
R1
VTRIP3
RSENSE
VTRIP2
RSENSE
+
MCP6544(1/4) Comparator 2 MCP6544(2/4) Comparator 3 MCP6544(3/4) Comparator 4 MCP6544(4/4)
VTRIP1
RSENSE
15
Users can select a at pass-band or sharp transition from pass-band to stop-band. Other options, such as minimum ripple factor, sharp transition and linear phase delays are available. Once the lter characteristics have been identied, the Mindi Active Filter Designer & Simulator can generate and simulate the schematic of lter circuit. For maximum design exibility, changes in resistor and capacitor values can be implemented to t the demands of the application. The tool will recalculate all values to meet the desired response, allowing real-world values to be substituted or changed as part of the design process. The tool also generates a Bill of Materials (BOM) of the designed lter. Both of these tools are available on the Microchip web site (www.microchip.com) under Design & Simulation Tools or on the Mindi home page (http://www.microchip.com/mindi). The op amps and evaluation boards can also be ordered from the Microchip web site.
16
Development Tools
These following development boards support the the development of signal chain applications. These product families may have other demonstration and evaluation boards that may also be useful. For more information visit www.microchip.com/analogtools
DACs
MCP4725 PICtail Plus Daughter Board
(MCP4725DM-PTPLS) This daughter board demonstrates the MCP4725 (12 bit DAC with non-volatile memory) features using the Explorer 16 Development Board and the PICkit Serial Analyzer.
ADCs
MCP3421 Battery Fuel Gauge Demo
(MCP3421DM-BFG) The MCP3421 Battery Fuel Gauge Demo Board demonstrates how to measure the battery voltage and discharging current using the MCP3421. The MCU algorithm calculates the battery fuel being used. This demo board is shipped with 1.5V AAA non-rechargeable battery. The board can also charge a single-cell 4.2V Li-Ion battery.
Op Amps
MCP6031 Photodiode PICtail Plus Demo Board
(MCP6031DM-PTPLS) The MCP6031 Photodiode PICtail Plus Demo Board demonstrates how to use a transimpedance amplifier, which consists of MCP6031 high precision op amp and external resistors, to convert photo-current to voltage.
17
Development Tools
MCP6V01 Input Offset Demo Board
(MCP6V01DM-VOS) The MCP6V01 Input Offset Demo Board is intended to provide a simple means to measure the MCP6V01/2/3 op amps input offset voltage (VOS) under a variety of bias conditions. This VOS includes the specified input offset voltage value found in the data sheet plus changes due to power supply voltage (PSRR), common mode voltage (CMRR), output voltage (AOL) and temperature (IVOS/ITA).
Temp Sensors
MCP9800 Temp Sensor Demo Board
(MCP9800DM-TS1) The MCP9800 Temperature Sensor Demo Board demonstrates the sensors features. Users can connect the demo board to a PC with USB interface and evaluate the sensor performance. The 7-Segment LED displays temperature in degrees Celsius or degrees Fahrenheit; the temperature alert feature can be set by the users using an on board potentiometer. An alert LED is used to indicate an over temperature condition. In addition, temperature can be datalogged using the Microchip Thermal Management Software Graphical User Interface (GUI). The sensor registers can also be programmed using the GUI.
18
Development Tools
RTD Reference Design Board (TMPSNSRD-RTD2) The RTD Reference Design demonstrates how to implement Resistive Temperature Detector (RTD) and accurately measure temperature. This solution uses the MCP3551 22-bit Analog-to-Digital Converter (ADC) to measure voltage across the RTD. The ADC and the RTD are referenced using an onboard reference voltage and the ADC inputs are directly connected to the RTD terminals. This provides a ratio metric temperature measurement. The solution uses a current limiting resistor to bias the RTD. It provides a reliable and accurate RTD instrumentation without the need for extensive circuit compensation and calibration routines. In addition, the this reference design includes a silicon temperature sensor, MCP9804. This sensor is used for comparison only, it is not needed to instrument an RTD. The MCP3551 and MCP9804 outputs are read using a USB PIC microcontroller. This controller is also connected to a PC using USB interface. The thermal management software is used plot the RTD temperature data in stripchart format. Thermocouple Reference Design Board
(TMPSNSRD-TCPL1) The Thermocouple Reference Design demonstrates how to implement a thermocouple and accurately sense temperature over the entire thermocouple measurement range. This solution uses the MCP3421 18-bit Analogto-Digital Converter (ADC) to measure voltage across the Thermocouple. The ADC has an internal 2.048V reference voltage and a Programmable Gain Amplifier with 1, 2, 4, 8V/V. At a Gain of 8 V/V the PGA effectively adds 3 LSb to the ADC. This increases the ADC resolution to 21-bit or 2 V/LSb. Therefore, the Thermocouple EMF voltage is measured with 2 V resolution. For K-type thermocouple, measurement system provides a 0.05C resolution. The cold-junction compensation is done using a 1C accurate 0.0625C resolution silicon temperature sensor, the MCP9804. This solution provides a reliable and accurate Thermocouple instrumentation without the need for extensive circuit compensation and calibration routines.
19
SAR ADCs
AN246: Driving the Analog Inputs of a SAR A/D Converter This application note delves into the issues surrounding the SAR converters input and conversion nuances to insure that the converter is handled properly from the beginning of the design phase. AN688: Layout Tips for 12-Bit A/D Converter Application This application note provides basic 12-bit layout guidelines, ending with a review of issues to be aware of. Examples of good layout and bad layout implementations are presented throughout. AN693: Understanding A/D Converter Performance Specifications This application note describes the specifications used to quantify the performance of A/D converters and give the reader a better understanding of the significance of those specifications in an application. AN842: Differential ADC Biasing Techniques, Tips and Tricks True differential converters can offer many advantages over single-ended input A/D Converters (ADC). In addition to their common mode rejection ability, these converters can also be used to overcome many DC biasing limitations of common signal conditioning circuits. AN845: Communicating With The MCP3221 Using PIC Microcontrollers This application note will cover communications between the MCP3221 12-bit A/D Converter and a PIC microcontroller. The code supplied with this application note is written as relocatable assembly code.
Delta-Sigma ADCs
AN1007: Designing with the MCP3551 Delta-Sigma ADC The MCP3551 delta-sigma ADC is a high-resolution converter. This application note discusses various design techniques to follow when using this device. Typical application circuits are discussed first, followed by a section on noise analysis. AN1030: Weigh Scale Applications for the MCP3551 This application note focusses specifically on load cells, a type of strain gauge that is typically used for measuring weight. Even more specifically, the focus is on fully active, temperature compensated load cells whose change in differential output voltage with a rated load is 2 mV to 4 mV per volt of excitation (the excitation voltage being the difference between the +Input and the Input terminals of the load cell). AN1156: Battery Fuel Measurement Using Delta-Sigma ADC Devices This application note reviews the battery fuel measurement using the MCU and ADC devices. Developing battery fuel measurement in this manner provides flexible solutions and enables economic management. DS21841: Analog-to-Digital Converter Design Guide 20
Signal Chain Design Guide
Utility Metering
Refer to DS01008: Utility Metering Solutions
Op Amps
AN679: Temperature Sensing Technologies Covers the most popular temperature sensor technologies and helps determine the most appropriate sensor for an application. AN681: Reading and Using Fast Fourier Transformation (FFT) Discusses the use of frequency analysis (FFTs), time analysis and DC analysis techniques. It emphasizes Analogto-Digital converter applications. AN684: Single Supply Temperature Sensing with Thermocouples Focuses on thermocouple circuit solutions. It builds from signal conditioning components to complete application circuits. AN695: Interfacing Pressure Sensors to Microchips Analog Peripherals Shows how to condition a Wheatstone bridge sensor using simple circuits. A piezoresistive pressure sensor application is used to illustrate the theory. AN699: Anti-Aliasing, Analog Filters for Data Acquisition Systems A tutorial on active analog filters and their most common applications. AN722: Operational Amplifier Topologies and DC Specifications Defines op amp DC specifications found in a data sheet. It shows where these specifications are critical in application circuits. AN723: Operational Amplifier AC Specifications and Applications Defines op amp AC specifications found in a data sheet. It shows where these specifications are critical in application circuits.
21
Temperature Sensing
AN929: Temperature Measurement Circuits for Embedded Applications This application note shows how to select a temperature sensor and conditioning circuit to maximize the measurement accuracy and simplify the interface to the microcontroller. AN981: Interfacing a MCP9700 Analog Temperature Sensor to a PIC Microcontroller Analog output silicon temperature sensors offer an easyto-use alternative to traditional temperature sensors, such as thermistors. The MCP9700 offers many system-level advantages, including the integration of the temperature sensor and signal-conditioning circuitry on a single chip. Analog output sensors are especially suited for embedded systems due to their linear output. This application note will discuss system integration, firmware implementation and PCB layout techniques for using the MCP9700 in an embedded system. AN988: Interfacing a MCP9800 I2C Digital Temperature Sensor to a PIC Microcontroller This application note will discuss system integration, firmware implementation and PCB layout techniques for using the MCP9800 in an embedded system. AN1001: IC Temperature Sensor Accuracy Compensation with a PIC Microcontroller This application note derives an equation that describes the sensors typical non-linear characteristics, which can be used to compensate for the sensors accuracy error over the specified operating temperature range.
22
LINEAR
LINEAR Op Amps
Device # per Package 1,2,1,4 1,2,1,4 1,2,1,4 1,2,1,4 1,2,1,4 1,1,1,2,4 1,2,4 1,1,1,2,4 1,2,4 1,1,1,2,4 1,2,4 1,1,2,1,4,2 1,1,2,1,4 1 1,1,2,1,4,2 1,1,2,1,4 1,1,2,1,4,2 1,2,2 1,2,1,2 1,2,2 1,2,1,2 GBWP (kHz) Typ. 10 14 100 155 190 300 385 550 730 1,000 1,200 2,000 2,800 3,500 5,000 10,000 10,000 20,000 24,000 50,000 60,000 IQ (A/amp.) Typ. 1 1 1 25 25 30 45 70 90 170 170 240 325 720 570 1,350 1,300 3,600 3,600 9,000 9,000 VOS (V) Max. 150 3,000 3,000 250 150 5,000 150 5,000 150 4,500 150 3,000 2,000 1,500 3,000 500, 250 3,000 200 8,000 200 8,000 Supply Voltage (V) 1.8 to 5.5 1.4 to 6.0 1.4 to 6.0 2.5 to 6.0 2.3 to 5.5 1.8 to 6.0 1.8 to 6.0 1.8 to 5.5 1.8 to 6.0 1.8 to 6.0 1.8 to 6.0 2.0 to 6.0 2.7 to 6.0 2.2 to 5.5 2.2 to 6.0 2.5 to 5.5 2.4 to 6.0 2.5 to 5.5 2.5 to 5.5 2.5 to 5.5 2.5 to 5.5 Temperature Range (C) -40 to +125 -40 to +85, -40 to +125 -40 to +85, -40 to +125 -40 to +85 -40 to +85 -40 to +125 -40 to +125 -40 to +125 -40 to +125 -40 to +85, -40 to +125 -40 to +125 -40 to +125 -40 to +85, -40 to +125 -40 to +125 -40 to +125 -40 to +85, -40 to +125 -40 to +125 -40 to +125 -40 to +125 -40 to +125 -40 to +125 Railto-Rail I/O I/O I/O I/O O O I/O I/O I/O I/O I/O I/O I/O O O I/O I/O I/O O O O O Features Packages SOIC, MSOP, TSSOP, DFN, SOT-23 PDIP, SOIC, MSOP, TSSOP, SOT-23 PDIP, SOIC, MSOP, TSSOP, SOT-23 PDIP, SOIC, TSSOP, DFN, SOT-23 PDIP, SOIC, TSSOP PDIP, SOIC, MSOP, TSSOP, DFN, SOT-23, SC-70 SOIC, TSSOP, TDFN PDIP, SOIC, MSOP, TSSOP, DFN, SOT-23, SC-70 SOIC, TSSOP, TDFN PDIP, SOIC, MSOP, TSSOP, SOT-23, SC-70 SOIC, TSSOP, TDFN PDIP, SOIC, MSOP, TSSOP, SOT-23 PDIP, SOIC, TSSOP, SOT-23 SOT-23 PDIP, SOIC, MSOP, TSSOP, SOT-23 PDIP, SOIC, MSOP, TSSOP, SOT-23 PDIP, SOIC, MSOP, TSSOP, SOT-23 SOIC, MSOP, DFN SOIC, MSOP, DFN SOIC, MSOP, DFN SOIC, MSOP, DFN Featured Demo Board MCP6031DM-PCTL, SOIC8EV, SOIC14EV SOIC8EV, SOIC14EV SOIC8EV, SOIC14EV SOIC8EV, SOIC14EV SOIC8EV, SOIC14EV VSUPEV2, SOIC8EV, SOIC14EV SOIC8EV, SOIC14EV VSUPEV2, SOIC8EV, SOIC14EV SOIC8EV, SOIC14EV MCP6SX2DM-PICTLPD, SOIC8EV, SOIC14EV SOIC8EV, SOIC14EV MCP6XXXDM-FLTR, SOIC8EV, SOIC14EV SOIC8EV, SOIC14EV VSUPEV2 VSUPEV2, SOIC8EV, SOIC14EV MCP6XXXEV-AMP1, SOIC8EV, SOIC14EV PIC16F690DM-PCTLHS, SOIC8EV, SOIC14EV MCP651EV-VOS MCP651EV-VOS MCP651EV-VOS MCP661DM-LD Op Amp Category
MCP6031/2/3/4 MCP6041/2/3/4 MCP6141/2/3/4 MCP606/7/8/9 MCP616/7/8/9 MCP6231/1R/1U/2/4 MCP6051/2/4 MCP6241/1R/1U/2/4 MCP6061/2/4 MCP6001/1R/1U/2/4 MCP6071/2/4 MCP6271/1R/2/3/4/5 MCP601/1R/2/3/4 MCP6286 MCP6281/1R/2/3/4/5 MCP6021/1R/2/3/4 MCP6291/1R/2/3/4/5 MCP621 MCP631/2/3/5 MCP651/2/5 MCP661/2/3/5
Low Power Mode on MCP6033 Low Power Mode on MCP6043 GMIN = 10, Low Power Mode on MCP6143 Low Power Mode on MCP608 Low Power Mode on MCP618 Low Power Mode on MCP6273, Cascaded Gain with MCP6275 Low Power Mode on MCP603 Low Noise Low Power Mode on MCP6283, Cascaded Gain with MCP6285 Low Power Mode on MCP6023 Low Power Mode on MCP6293, Cascaded Gain with MCP6295 mCal (offset correction, low power mode) Low Power Mode on MCP633/5 mCal (offset correction, low power mode) Low Power Mode on MCP663/5
Low Offset, Low Power General Purpose, Low Power General Purpose, Low Power Low Offset Low Offset General Purpose Low Offset General Purpose Low Offset General Purpose Low Offset General Purpose General Purpose Low Noise General Purpose Low Offset General Purpose High Speed, High Output Drive, Low Offset High Speed, High Output Drive High Speed, High Output Drive, Low Offset High Speed, High Output Drive
MCP6V01/2/3 MCP6V06/7/8
Auto-zeroed Auto-zeroed
23
LINEAR Comparators
Device MCP6541 MCP6542 MCP6543 MCP6544 MCP6546 MCP6547 MCP6548 MCP6549 MCP6561 MCP6562 MCP6564 MCP6566 MCP6567 MCP6569 # per Package 1 2 1 4 1 2 1 4 1 2 4 1 2 4 VREF (V) Typical Propagation Delay (s) 4 4 4 4 4 4 4 4 0.047 0.047 0.047 0.047 0.047 0.047 IQ Typical (A) 1 1 1 1 1 1 1 1 100 100 100 100 100 100 Vos Max (mV) 5 5 5 5 5 5 5 5 10 10 10 10 10 10 Operating Voltage (V) 1.6 to 5.5 1.6 to 5.5 1.6 to 5.5 1.6 to 5.5 1.6 to 5.5 1.6 to 5.5 1.6 to 5.5 1.6 to 5.5 1.8 to 5.5 1.8 to 5.5 1.8 to 5.5 1.8 to 5.5 1.8 to 5.5 1.8 to 5.5 Temperature Range (C) -40 to +125 -40 to +125 -40 to +125 -40 to +125 -40 to +125 -40 to +125 -40 to +125 -40 to +125 -40 to +125 -40 to +125 -40 to +125 -40 to +125 -40 to +125 -40 to +125 Features Push-Pull, Rail-to-Rail Input/Output Push-Pull, Rail-to-Rail Input/Output Push-Pull, Rail-to-Rail Input/Output, Chip Select Push-Pull, Rail-to-Rail Input/Output Open-drain, 9V, Rail-to-Rail Input/Output Open-drain, 9V, Rail-to-Rail Input/Output Open-drain, 9V, Rail-to-Rail Input/Output, Chip Select Open-drain, 9V, Rail-to-Rail Input/Output Push-Pull, Rail-to-Rail Input/Output Push-Pull, Rail-to-Rail Input/Output Push-Pull, Rail-to-Rail Input/Output Open-Drain, Rail-to-Rail Input/Output Open-Drain, Rail-to-Rail Input/Output Open-Drain, Rail-to-Rail Input/Output Packages 5-pin SOT-23(S,R,U), 5-pin SC-70(S,U), 8-pin PDIP, 8-pin SOIC, 8-pin MSOP 8-pin PDIP, 8-pin SOIC, 8-pin MSOP 8-pin PDIP, 8-pin SOIC, 8-pin MSOP 14-pin PDIP, 14-pin SOIC, 14-pin TSSOP 5-pin SOT-23(S,R,U), 5-pin SC-70(S,U), 8-pin PDIP, 8-pin SOIC, 8-pin MSOP 8-pin PDIP, 8-pin SOIC, 8-pin MSOP 8-pin PDIP, 8-pin SOIC, 8-pin MSOP 14-pin PDIP, 14-pin SOIC, 14-pin TSSOP 5-pin SOT-23(S,R,U), 5-pin SC-70(S) 8-pin SOIC, 8-pin MSOP 14-pin SOIC, 14-pin TSSOP 5-pin SOT-23(S,R,U), 5-pin SC-70(S) 8-pin SOIC, 8-pin MSOP 14-pin SOIC, 14-pin TSSOP
MIXED SIGNAL
MIXED SIGNAL Delta-Sigma A/D Converters
Device MCP3421 MCP3422 MCP3423 MCP3424 MCP3425 MCP3426 MCP3427 MCP3428 Resolution (bits) 18 18 18 18 16 16 16 16 Max.Sample Rate (samples/sec) 3.75 3.75 3.75 3.75 15 15 15 15 # of Input Channels 1 Diff 2 Diff 2 Diff 4 Diff 1 Diff 2 Diff 2 Diff 4 Diff Interface I2C IC IC IC IC IC IC IC Supply Voltage (V) 2.7 to 5.5 2.7 to 5.5 2.7 to 5.5 2.7 to 5.5 2.7 to 5.5 2.7 to 5.5 2.7 to 5.5 2.7 to 5.5 Typical Supply Current (A) 145 (continuous) 39 (one shot) 145 145 145 155 145 145 145 Typical INL (ppm) 10 10 10 10 10 10 10 10 Temperature Range (C) -40 to +85 -40 to +85 -40 to +85 -40 to +85 -40 to +85 -40 to +85 -40 to +85 -40 to +85 Features PGA: 1, 2, 4 or 8 Internal voltage reference PGA: 1, 2, 4, or 8 Internal voltage reference PGA: 1, 2, 4, or 8 Internal voltage reference PGA: 1, 2, 4, or 8 Internal voltage reference PGA: 1, 2, 4, or 8 Internal voltage reference PGA: 1, 2, 4, or 8 Internal voltage reference PGA: 1, 2, 4, or 8 Internal voltage reference PGA: 1, 2, 4, or 8 Internal voltage reference Packages SOT-23-6 SOIC-8, MSOP-8, DFN-8 MSOP-10, DFN-10 SOIC-14, TSSOP-14 SOT-23-6 SOIC-8, MSOP-8, DFN-8 MSOP-10, DFN-10 SOIC-14, TSSOP-14 Featured Demo Board MCP3421EV MCP3422EV, MCP3421DM-BFG MCP3423EV MCP3424EV MCP3425EV, MCP3421DM-BFG
24
I2C I2C SPI SPI SPI SPI SMbus/ I2C SMbus/ I2C
25
VDD Operating Range(1) 1.8V to 5.5V 1.8V to 5.5V 1.8V to 5.5V 1.8V to 5.5V 1.8V to 5.5V 1.8V to 5.5V 1.8V to 5.5V 1.8V to 5.5V 1.8V to 5.5V 1.8V to 5.5V 2.7V to 5.5V 2.7V to 5.5V 2.7V to 5.5V 2.7V to 5.5V 2.7V to 5.5V 2.7V to 5.5V 2.7V to 5.5V 2.7V to 5.5V 2.7V to 5.5V 2.7V to 5.5V 1.8V to 5.5V 1.8V to 5.5V 2.7V to 5.5V 2.7V to 5.5V 1.8V to 5.5V 1.8V to 5.5V 2.7V to 5.5V 2.7V to 5.5V 1.8V to 5.5V 1.8V to 5.5V 2.7V to 5.5V 2.7V to 5.5V 1.8V to 5.5V 1.8V to 5.5V 2.7V to 5.5V 2.7V to 5.5V 1.8V to 5.5V 1.8V to 5.5V
Volatile/ Non-Volatile Volatile Volatile Volatile Volatile Volatile Volatile Volatile Volatile Volatile Volatile Non-Volatile Non-Volatile Non-Volatile Non-Volatile Volatile Volatile Volatile Volatile Volatile Volatile Volatile Volatile Non-Volatile Non-Volatile Volatile Volatile Non-Volatile Non-Volatile Volatile Volatile Non-Volatile Non-Volatile Volatile Volatile Non-Volatile Non-Volatile Volatile Volatile
Resistance (ohms) 2.1K, 5K, 10K, 50K 2.1K, 5K, 10K, 50K 2.1K, 5K, 10K, 50K 2.1K, 5K, 10K, 50K 5K, 10K, 50K, 100K 5K, 10K, 50K, 100K 5K, 10K, 50K, 100K 5K, 10K, 50K, 100K 5K, 10K, 50K, 100K 5K, 10K, 50K, 100K 2.1K, 5K, 10K, 50K 2.1K, 5K, 10K, 50K 2.1K, 5K, 10K, 50K 2.1K, 5K, 10K, 50K 10K 50K 100K 10K 50K 100K 5K, 10K, 50K, 100K 5K, 10K, 50K, 100K 5K, 10K, 50K, 100K 5K, 10K, 50K, 100K 5K, 10K, 50K, 100K 5K, 10K, 50K, 100K 5K, 10K, 50K, 100K 5K, 10K, 50K, 100K 5K, 10K, 50K, 100K 5K, 10K, 50K, 100K 5K, 10K, 50K, 100K 5K, 10K, 50K, 100K 5K, 10K, 50K, 100K 5K, 10K, 50K, 100K 5K, 10K, 50K, 100K 5K, 10K, 50K, 100K 5K, 10K, 50K, 100K 5K, 10K, 50K, 100K
INL (Max.) 0.5 LSb 0.5 LSb 0.5 LSb 0.5 LSb 0.5 LSb 0.5 LSb 0.5 LSb 0.5 LSb 0.5 LSb 0.5 LSb 0.5 LSb 0.5 LSb 0.5 LSb 0.5 LSb 1 LSb 1 LSb 1 LSb 1 LSb 1 LSb 1 LSb 0.5 LSb 0.5 LSb 0.5 LSb 0.5 LSb 1 LSb 1 LSb 1 LSb 1 LSb 0.5 LSb 0.5 LSb 0.5 LSb 0.5 LSb 1 LSb 1 LSb 1 LSb 1 LSb 1.0 LSb 1.0 LSb
DNL (Max.) 0.5 LSb 0.5 LSb 0.5 LSb 0.5 LSb 0.25 LSb 0.25 LSb 0.25 LSb 0.25 LSb 0.25 LSb 0.25 LSb 0.5 LSb 0.5 LSb 0.5 LSb 0.5 LSb 1 LSb 1 LSb 1 LSb 1 LSb 1 LSb 1 LSb 0.25 LSb 0.25 LSb 0.25 LSb 0.25 LSb 0.5 LSb 0.5 LSb 0.5 LSb 0.5 LSb 0.25 LSb 0.25 LSb 0.25 LSb 0.25 LSb 0.5 LSb 0.5 LSb 0.5 LSb 0.5 LSb 0.5 LSb 0.5 LSb
Temperature Range (C) -40 to +125 -40 to +125 -40 to +125 -40 to +125 -40 to +125 -40 to +125 -40 to +125 -40 to +125 -40 to +125 -40 to +125 -40 to +125 -40 to +125 -40 to +125 -40 to +125 -40 to +85 -40 to +85 -40 to +85 -40 to +85 -40 to +85 -40 to +85 -40 to +125 -40 to +125 -40 to +125 -40 to +125 -40 to +125 -40 to +125 -40 to +125 -40 to +125 -40 to +125 -40 to +125 -40 to +125 -40 to +125 -40 to +125 -40 to +125 -40 to +125 -40 to +125 -40 to +125 -40 to +125 SOIC-8 SOT-23-6 SOT-23-6 SOT-23-5 SC-70-6 SC-70-6 SC-70-5 SC-70-6 SC-70-6 SC-70-5 SOIC-8 SOT-23-6 SOT-23-6 SOT-23-5
Packages
Featured Demo Board MCP402XEV, MCP4XXXDM-DB MCP402XEV, SC70EV MCP402XEV, SC70EV MCP402XEV, SC70EV SC70EV SC70EV SC70EV SC70EV SC70EV SC70EV MCP402XEV, MCP4XXXDM-DB MCP402XEV, SC70EV MCP402XEV, SC70EV MCP402XEV, SC70EV MCP4XXXDM-DB MCP4XXXDM-DB MCP4XXXDM-DB MCP4XXXDM-DB MCP4XXXDM-DB MCP4XXXDM-DB MCP42XXDM-PTPLS MCP42XXDM-PTPLS MCP42XXDM-PTPLS MCP42XXDM-PTPLS MCP42XXDM-PTPLS MCP42XXDM-PTPLS MCP42XXDM-PTPLS MCP42XXDM-PTPLS MCP4XXXDM-DB, MCP42XXDM-PTPLS MCP42XXDM-PTPLS MCP4XXXDM-DB, MCP42XXDM-PTPLS MCP42XXDM-PTPLS MCP4XXXDM-DB, MCP42XXDM-PTPLS MCP42XXDM-PTPLS MCP4XXXDM-DB, MCP42XXDM-PTPLS MCP42XXDM-PTPLS TSSOP20EV TSSOP20EV
PDIP-8, SOIC-8 PDIP-8, SOIC-8 PDIP-8, SOIC-8 PDIP-14, SOIC-14, TSSOP-14 PDIP-14, SOIC-14, TSSOP-14 PDIP-14, SOIC-14, TSSOP-14 PDIP-8, SOIC-8, MSOP-8, DFN-8 PDIP-8, SOIC-8, MSOP-8, DFN-8 PDIP-8, SOIC-8, MSOP-8, DFN-8 PDIP-8, SOIC-8, MSOP-8, DFN-8 PDIP-8, SOIC-8, MSOP-8, DFN-8 PDIP-8, SOIC-8, MSOP-8, DFN-8 PDIP-8, SOIC-8, MSOP-8, DFN-8 PDIP-8, SOIC-8, MSOP-8, DFN-8 PDIP-14, SOIC-14, TSSOP-14, QFN-16 MSOP-10, DFN-10 PDIP-14, SOIC-14, TSSOP-14, QFN-16 MSOP-10, DFN-10 PDIP-14, SOIC-14, TSSOP-14, QFN-16 MSOP-10, DFN-10 PDIP-14, SOIC-14, TSSOP-14, QFN-16 MSOP-10, DFN-10 TSSOP-20, QFN-20 TSSOP-14
26
VDD Operating Range(1) 2.7V to 5.5V 2.7V to 5.5V 1.8V to 5.5V 1.8V to 5.5V 2.7V to 5.5V 2.7V to 5.5V 1.8V to 5.5V 1.8V to 5.5V 2.7V to 5.5V 2.7V to 5.5V 1.8V to 5.5V 1.8V to 5.5V 2.7V to 5.5V 2.7V to 5.5V 1.8V to 5.5V 1.8V to 5.5V 2.7V to 5.5V 2.7V to 5.5V
Volatile/ Non-Volatile Non-Volatile Non-Volatile Volatile Volatile Non-Volatile Non-Volatile Volatile Volatile Non-Volatile Non-Volatile Volatile Volatile Non-Volatile Non-Volatile Volatile Volatile Non-Volatile Non-Volatile
Resistance (ohms) 5K, 10K, 50K, 100K 5K, 10K, 50K, 100K 5K, 10K, 50K, 100K 5K, 10K, 50K, 100K 5K, 10K, 50K, 100K 5K, 10K, 50K, 100K 5K, 10K, 50K, 100K 5K, 10K, 50K, 100K 5K, 10K, 50K, 100K 5K, 10K, 50K, 100K 5K, 10K, 50K, 100K 5K, 10K, 50K, 100K 5K, 10K, 50K, 100K 5K, 10K, 50K, 100K 5K, 10K, 50K, 100K 5K, 10K, 50K, 100K 5K, 10K, 50K, 100K 5K, 10K, 50K, 100K
INL (Max.) 1.0 LSb 1.0 LSb 0.5 LSb 0.5 LSb 0.5 LSb 0.5 LSb 1 LSb 1 LSb 1 LSb 1 LSb 0.5 LSb 0.5 LSb 0.5 LSb 0.5 LSb 1 LSb 1 LSb 1 LSb 1 LSb
DNL (Max.) 0.5 LSb 0.5 LSb 0.25 LSb 0.25 LSb 0.25 LSb 0.25 LSb 0.5 LSb 0.5 LSb 0.5 LSb 0.5 LSb 0.25 LSb 0.25 LSb 0.25 LSb 0.25 LSb 0.5 LSb 0.5 LSb 0.5 LSb 0.5 LSb
Temperature Range (C) -40 to +125 -40 to +125 -40 to +125 -40 to +125 -40 to +125 -40 to +125 -40 to +125 -40 to +125 -40 to +125 -40 to +125 -40 to +125 -40 to +125 -40 to +125 -40 to +125 -40 to +125 -40 to +125 -40 to +125 -40 to +125
Packages TSSOP-20, QFN-20 TSSOP-14 MSOP-8, DFN-8 MSOP-8, DFN-8 MSOP-8, DFN-8 MSOP-8, DFN-8 MSOP-8, DFN-8 MSOP-8, DFN-8 MSOP-8, DFN-8 MSOP-8, DFN-8 TSSOP-14, QFN-16 MSOP-10, DFN-10 TSSOP-14, QFN-16 MSOP-10, DFN-10 TSSOP-14, QFN-16 MSOP-10, DFN-10 TSSOP-14, QFN-16 MSOP-10, DFN-10
Featured Demo Board TSSOP20EV TSSOP20EV MCP46XXDM-PTPLS MCP46XXDM-PTPLS MCP46XXDM-PTPLS MCP46XXDM-PTPLS MCP46XXDM-PTPLS MCP46XXDM-PTPLS MCP46XXDM-PTPLS MCP46XXDM-PTPLS MCP4XXXDM-DB, MCP46XXDM-PTPLS MCP46XXDM-PTPLS MCP4XXXDM-DB, MCP46XXDM-PTPLS MCP46XXDM-PTPLS MCP4XXXDM-DB, MCP46XXDM-PTPLS MCP46XXDM-PTPLS MCP4XXXDM-DB, MCP46XXDM-PTPLS MCP46XXDM-PTPLS
THERMAL MANAGEMENT
THERMAL MANAGEMENT PRODUCTS Temperature Sensors
Part # Typical Accuracy (C) Maximum Accuracy @ 25C (C) Maximum Temperature Range (C) Vcc Range (V) Maximum Supply Current (A) Resolution (bits) Packages Featured Demo Board
Serial Output Temperature Sensors MCP9800 MCP9801 MCP9802 MCP9803 MCP9804 MCP9805 MCP98242 MCP98243 TC72 TC74 TC77 TCN75 TCN75A 0.5 0.5 0.5 0.5 0.25 2 2 0.5 0.5 0.5 0.5 0.5 0.5 1 1 1 1 1 3 3 3 2 2 1 3 3 -55 to +125 -55 to +125 -55 to +125 -55 to +125 -40 to +125 -40 to +125 -40 to +125 -40 to +125 -55 to +125 -40 to +125 -55 to +125 -55 to +125 -40 to +125 +2.7 to +5.5 +2.7 to +5.5 +2.7 to +5.5 +2.7 to +5.5 +2.7 to +5.5 3.0 to 3.6 3.0 to 3.6 3.0 to 3.6 +2.7 to +5.5 +2.7 to +5.5 +2.7 to +5.5 +2.7 to +5.5 +2.7 to +5.5 400 400 400 400 400 500 500 500 400 350 400 1000 400 9-12 9-12 9-12 9-12 12-bits 10 10 11 10 8 12 9 9-12 SOT-23-5 SOIC-8 150 mil, MSOP-8 SOT-23-5 SOIC-8 150 mil, MSOP-8 MSOP-8, DFN-8 TSSOP-8, DFN-8 TSSOP-8, DFN-8, TDFN-8, UDFN-8 TSSOP-8, DFN-8, TDFN-8, UDFN-8 MSOP-8, DFN-8 SOT-23-5, TO-220-5 SOIC-8 150 mil, SOT-23-5 SOIC-8 150 mil, MSOP-8 SOIC-8 150 mil, MSOP-8 MCP9800DM-TS1 MCP9800DM-TS1 MCP9800DM-TS1 MCP9800DM-TS1 TMPSNSRD-RTD2, TMPSNSRD-TCPL1 TC72DM-PICTL TC74DEMO TC77DM-PICTL
27
Logic Output Temperature Sensors MCP9509 MCP9510 TC620 TC621 TC622 TC623 TC624 TC6501 TC6502 TC6503 TC6504 0.5 0.5 1 1 1 1 1 0.5 0.5 0.5 0.5 NA NA 3 3 5 3 5 4 4 4 4 -40 to +125 -40 to +125 -55 to 125 -55 to 125 -40 to +125 -40 to +125 -40 to +125 -55 to 135 -55 to 135 -55 to 135 -55 to 135 2.7 to 5.5 2.7 to 5.5 4.5 to 18 4.5 to 18 4.5 to 18 2.7 to 4.5 2.7 to 4.5 2.7 to 5.5 2.7 to 5.5 2.7 to 5.5 2.7 to 5.5 50 80 400 400 600 250 300 40 40 40 40 SOT-23-5 SOT-23-6 PDIP-8, SOIC-8 150 mil PDIP-8, SOIC-8 150 mil PDIP-8, SOIC-8 150 mil, TO-220-5 PDIP-8, SOIC-8 150 mil PDIP-8, SOIC-8 150 mil SOT-23-5 SOT-23-5 SOT-23-5 SOT-23-5
Voltage Output Temperature Sensors MCP9700 MCP9700A MCP9701 MCP9701A TC1046 TC1047 TC1047A TC1047A 1 1 1 1 0.5 0.5 0.5 0.5 4 2 4 2 2 2 2 2 -40 to +150 -40 to +150 -40 to +125 -40 to +125 -40 to +125 -40 to +125 -40 to +125 -40 to +125 2.3 to 5.5 2.3 to 5.5 +3.1 to +5.5 +3.1 to +5.5 2.7 to 4.4 2.7 to 4.4 +2.5 to +5.5 +2.5 to +5.5 6 6 6 6 60 60 60 60 SC-70-5, SOT-23-3, TO-92-3 SC-70-5, SOT-23-3, TO-92-3 SC-70-5, SOT-23-3, TO-92-3 SC-70-5, SOT-23-3, TO-92-3 SOT-23-3 SOT-23-3 SOT-23-3 SOT-23B-3 MCP9700DM-PCTL MCP9700DM-PCTL MCP9700DM-PCTL MCP9700DM-PCTL TC1047ADM-PICTL TC1047ADM-PICTL
POWER MANAGEMENT
POWER MANAGEMENT Voltage References
Part # MCP1525 MCP1541 Vcc Range (V) 2.7 to 5.5 4.3 to 5.5 Output Voltage (V) 2.5 4.096 Max. Load Current (mA) 2 2 Initial Accuracy (max.%) 1 1 Temperature Coefcient (ppm/C) 50 50 Maximum Supply Current (A @ 25C) 100 100 Packages SOT-23B-3, TO-92-3 SOT-23B-3, TO-92-3
28
Power Management
LDO & Switching Regulators Charge Pump DC/DC Converters Power MOSFET Drivers PWM Controllers System Supervisors Voltage Detectors Voltage References Li-Ion/Li-Polymer Battery Chargers
Linear
Op Amps Programmable Gain Ampliers Comparators
Mixed-Signal
A/D Converter Families Digital Potentiometers D/A Converters V/F and F/V Converters Energy Measurement ICs
Interface
CAN Peripherals Infrared Peripherals LIN Transceivers Serial Peripherals Ethernet Controllers USB Peripheral
29
Support
Microchip is committed to supporting its customers in developing products faster and more efficiently. We maintain a worldwide network of field applications engineers and technical support ready to provide product and system assistance. In addition, the following service areas are available at www.microchip.com: Support link provides a way to get questions answered fast: http://support.microchip.com Sample link offers evaluation samples of any Microchip device: http://sample.microchip.com Forum link provides access to knowledge base and peer help: http://forum.microchip.com Buy link provides locations of Microchip Sales Channel Partners: www.microchip.com/sales
Training
If additional training interests you, then Microchip can help. We continue to expand our technical training options, offering a growing list of courses and in-depth curriculum locally, as well as significant online resources whenever you want to use them. Regional Training Centers: www.microchip.com/rtc MASTERs Conferences: www.microchip.com/masters Worldwide Seminars: www.microchip.com/seminars eLearning: www.microchip.com/webseminars Resources from our Distribution and Third Party Partners www.microchip.com/training
Information subject to change. The Microchip name and logo, the Microchip logo and PIC are registered trademarks of Microchip Technology Incorporated in the U.S.A. and other countries. FilterLab, MXDEV and MXLAB are registered trademarks of Microchip Technology Incorporated in the U.S.A. FanSense, Select Mode and WiperLock are trademarks of Microchip Technology Incorporated in the U.S.A. and other countries. All other trademarks mentioned herein are property of their respective companies. 2010, Microchip Technology Incorporated. All Rights Reserved. Printed in the U.S.A. 4/10 DS21825F
www.microchip.com
Microchip Technology Inc. 2355 W. Chandler Blvd. Chandler, AZ 85224-6199
*DS21825F*