TESTO ITC KORINNA 28mm Allargato: Monoblock Directional Control Valve

TESTO ITC KORINNA 28mm Allargato
MONOBLOCK DIRECTIONAL
CONTROL VALVE
SD5
Features
Simple , compact and heavy duty designed monoblock valves from 1 to 7 sections for open and closed centre hydraulic systems..
H Fitted with a main pressure relief valve and a load check valve.
H Available with parallel, series or tandem circuit.
H Optional carry--over port (only for parallel or tandem circuit).
H Diameter 16 mm -- 0.63 in interchangeable spools.
H A wide variety of service port valve options.
H Actuation is manual, pneumatic, electro--pneumatic, hydraulic, electro--hydraulic, with solenoid and remote with flexible cables
spool control kits.
Additional information
This catalogue shows the product in the most standard configurations.
Please contact Sales Dpt. for more detailed information or special request.
WARNING!
All specifications of this catalogue refer to the standard product at this date.
Walvoil, oriented to a continuous improvement, reserves the right to
discontinue, modify or revise the specifications, without notice.
WALVOIL IS NOT RESPONSIBLE FOR ANY DAMAGE CAUSED BY AN 1st edition April 2005:
INCORRECT USE OF THE PRODUCT. This edition supercedes all prior documents.
2 DAU003E
SD5
Contents
Working condition . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 4
Performance data . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 5
Directional valve with left inlet . . . . . . . . . . . . . . . . . . . . . . 7
Directional valve with right inlet . . . . . . . . . . . . . . . . . . . . 77
Installation and maintenance . . . . . . . . . . . . . . . . . . . . . 126
Accessories . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 129
DAU003E 3
SD5
Working conditions
This catalogue shows technical specifications and diagrams measured with mineral oil of 46 mm2/s -- 46 cSt viscosity at 40°C tempera-
ture.
Nominal flow rating 45 l/min

Operating pressure (maximum) parallel pr tandem circuit 315 bar 4600 psi
series circuit 250 bar 3600 psi
Max. back pressure on outlet port T 25 bar 360 psi
∆p=100 bar -- 1450psi
Internal leakage A(B)→T 3 cm3/min 0.18 in 3/min
with fluid and valve at 40°C
Hydraulic fluid Mineral base oil
Fluid temperature with NBR seals from --20° to 80°C
with FPM seals from --20° to 100°C
Viecosity operating range from 15 to 75 mm2/s from 15 to 75 cSt
minimum 12 mm2/s 12 cSt
maximum 400 mm2/s 400 cSt
Max. level of contamination 19/16 -- ISO 4406
Ambient temperature from --40° to 60°C
NOTE -- For different conditions please contact Sales Dept.
Standard threads
REFERENCE STANDARDS
BSP UN--UNF METRIC NPTF
THREAD ISO 228/1 ISO 263 ISO 262 ANSI B1.20.3
ACCORDING TO BS 2779 ANSI B1.1 unified
CAVITY ISO 1179 11926 9974--1

ACCORDING TO SAE J1926 J2244 J476a
DIN 3852--2 3852--1
shape X o Y shape X o Y
PORTS THREAD
MAIN PORTS BSP UN--UNF METRICA
IInlet P and carry--over C G 3/8 3/4--16 (SAE 8) M18x1,5
Ports A and B G 3/8 9/16--18 (SAE 6) M18x1,5
G 3/8 M18x1,5
Outlet T 3/4--16 (SAE 8)
G 1/2 * M22x1,5 *
CONTROL PILOT PORTS
Pneumatics NPTF 1/8--27 NPTF 1/8--27 NPTF 1/8--27
Hydraulics G 1/4 9/16--18 (SAE 6) G 1/4
(*) -- Only for series circuit..
4 DAU003E
SD5
Performance data (pressure drop vs. flow)
Open centre
From side inlet to side outlet.
40
(bar) 540
(psi)
30
A1 A2 A3 A4 A5 A6 A7 7 sections
Pressure drop
360
T
P 20 4 sections
B1 B2 B3 B4 B5 B6 B7
2 sections
180
10
0
0 15 30 45 60
Flow (l/min)
Inlet to work port

From side inlet to A port (spool in position 1) or B port (spool in position 2).
40
(bar) 540
(psi)
30
A1 A2 A3 A4 A5 A6 A7
360
Pressure drop
T P→A7(B7)
P 20
B1 B2 B3 B4 B5 B6 B7
P→A1(B1) 180
10
0
0 15 30 45 60
Flow (l/min)
Work port to outlet

From A port (spool in position 2) or B port (spool in position 1) to side outlet.
40
(bar) 540
(psi)
30
A1 A2 A3 A4 A5 A6 A7 A1(B1)→T
Pressure drop
360
T
P 20
B1 B2 B3 B4 B5 B6 B7 A7(B7)→T
180
10
0
0 15 30 45 60
Flow (l/min)
NOTE -- Measured with spool type 1.
DAU003E 5
SD5
6 DAU003E
SD5
Contents
Directional valve with parallel circuit

Dimensional data . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 8
Hydraulic circuit . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 9
Ordering codes . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 10
Inlet relief options . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 12
Spools . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 13
“A” side spool positioners . . . . . . . . . . . . . . . . . . . . . . . . . . 20
“B” side options . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 39
Complete controls . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 44
Outlet port options . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 49
Service and auxiliary valves
ordering codes . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 52
port relief valves . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 54
pilot check valves . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 56
flange mounted relief valves . . . . . . . . . . . . . . . . . . . . . 55
antishock valves . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 57
fixed setting antishock and anticavitation valves . . . . . 59
adjustable setting antishock and anticavitation valves 61
flow control valves . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 65
Other executions
Main features . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 69
Directional valve SD5/1--N . . . . . . . . . . . . . . . . . . . . . . . . . . 70
Directional valve SD5/1--D . . . . . . . . . . . . . . . . . . . . . . . . . . 71
Directional valve SD5--S with series circuit . . . . . . . . . . . . 72
Directional valve SD5--SP with tandem circuit . . . . . . . . . . 74
DAU003E 7
SD5 directional valve with left inlet
Dimensional data (parallel circuit)
E Carry--over 63,5 5
20,5 2.50 0.20
12,5 F 0.81 45
0.06 1.77
0.33
8,5
1.34
34
4.06
3.19
103
7.32
81
186
2.01
51
spool out
45,5
1.79
3
0.45
11,5
1
24°
0.79
20
15°
0
1.77
45
M8 15°
24°
2
23 30 37 27 24,5
0.91 1.18 1.46 1.06 0.96
90 3
3.54 spool in
WALVOIL Valve type

MADE IN ITALY
WALVOIL
102219002
P0000001
SD5/2--P
SD5/2--P
Production batch:
P0500001 P05 = production year (2005)
1022004092 00001 = progressive number
MADE IN ITALY
Valve code
E F Weight E F Weight
TYPE TYPE
mm in mm in kg lb mm in mm in kg lb
SD5/1--P 100.5 3.96 73 2.87 3.5 7.7 SD5/5--P 248.5 9.78 221 8.70 10.1 22.3
SD5/2--P 137.5 5.41 110 4.33 5.2 11.5 SD5/6--P 285.5 11.24 258 10.16 11.7 25.8
SD5/3--P 174.5 6.87 147 5.79 6.9 15.2 SD5/7--P 322.5 12.70 295 11.61 13.2 29.1
SD5/4--P 211.5 8.33 184 7.24 8.1 17.9
8 DAU003E
directional valve with left inlet SD5
Hydraulic circuit
Parallel
Standard configuration with side inlet and outlet and open centre (AET execution).
Positioner kit
Port A line
Check valve
Allen wrench 4 Port B line
24 Nm / 17.7 lbft
A Pressure line Tank line
B P
Flow through
(LC)
Plug for open centre
Allen wrench 8
24 Nm / 17.7 lbft
Main relief valve
Lever pivot box
Standard configuration Configuration with upper inlet and outlet

T
A1 B1 A2 B2 A1 B1 A2 B2
P
T
120 120
1750 1750
Description example Description example:

SD5/2--P(JG3--120)/18L/18L/AET SD5/2--P(JG3--120)/18L/18L/AET--PSA
DAU003E 9
Ordering codes3.
Description example: Valve setting (bar)

Valve setting (bar) 1st section following section
SD5 / 2 -- P (JG3-- 120) / 1 8 L / 1 8IM . P3(G3-- 100) / AET *
1. 2. 3. 4. 5. 6. 7. 8.
9. I
6. 7.
8.
3.
4. II
1.
2.
5.
1. Body kits * 3. Spool options page 13

TYPE CODE DESCRIPTION TYPE CODE DESCRIPTION
1-- P 5KC1193000 Parallel, 1 section 1 3CU1210130 Double acting, 3 positions, with A and B
2-- P 5KC1223000 Parallel, 2 sections closed in neutral position
3-- P 5KC1243000 Parallel, 3 sections 1A 3CU1221130 Double acting, 3 positions, with A open to
4-- P 5KC1273000 Parallel, 4 sections tank in neutral position
5-- P 5KC1313000 Parallel, 5 sections 1B 3CU1222130 Double acting, 3 positions, with B open to
7-- P 5KC13E3000 Parallel, 7 sections 2 3CU1225130 Double acting, 3 positions, with A and B
Include boby, seals and load check valve. open to tank in neutral position
2H 3CU1225225 Double acting, 3 positions, with A e B
partially open to tank in neutral position
2. Inlet relief options page 12 3 3CU1231130 Single acting on A, 3 positions, B plugged
TYPE CODE DESCRIPTION requires G3/8 plug (see part I )
VMD5 direct pressure relief valve type J Special spools for particular positioner kits . . . . . . . . . . . . . . . page 16
Standard setting is referred to 10 l/min flow. 5DY 3CU1242220 Double acting, 4 positions, floating circuit
(JG2-- 63) 5KIT105412 Range 40 to 63 bar / 580 to 900 psi in 4th position with spool in
standard setting 63 bar / 900 psi 5PY 3CU1245620 Double acting, 4 positions, floating circuit
(JG3-- 120) 5KIT105413 Range 50 to 200 bar / 725 to 2900 psi in 4th position with spool out, with check
standard setting 120 bar / 1750 psi valve
(JG4-- 220) 5KIT105414 Range 160 to 315 bar / 2300 to 4600 psi 8 3CU1262120 Double acting, 4 positions, regenerative
standard setting 220 bar / 3200 psi circuit in 4th position with spool in
SV XTAP623282 Relief valve blanking plug Special spools for standard positioner kits . . . . . . . . . . . . . . . . page 19
8F 3CU1261100 Double acting, 3 positions, regenerative
circuit in 2nd position with spool out
NOTE (*) -- Codes are referred to BSP threads.
10 DAU003E
Ordering codes
4. “A” side spool positioners page 20 4. “A” side spool positioners

TYPE CODE DESCRIPTION Particular positioner kits for special spools . . . . . . . . . . . . . . . page 36
8 5V08105000 With spring return in neutral position 13NZ 5V13305010 4 pos. with spring return in neutral pos.
8D 5V08105200 With spring return in neutral position and and detent in 4th pos.: for spool 5DY
pin with M6 female thread for dual control 13QN 5V13405020 4 pos. with spring return in neutral pos.
8D2 5V08105220 With spring return in neutral position and and detent in 4th pos.: for spool 5PY
pin with M8 male thread for dual control 13FZ 5V13505400 4 positions with spring return in neutral
8F2 5V08105101 With spring return in neutral position and position: for spool 8
adjustable flow limiter 13QNMG3(NO) 5V135405660 As type 13QN with microswitch in
19 5V19105000 2 positions, with spring return in neutral positions 1 and 2: for spool 5PY
position from position 1
20 5V19105000 2 positions, with spring return in neutral 5. “B” side options page 39
9 5V09105010 With detent in position 1 and spring return TYPE CODE DESCRIPTION
in neutral position L 5LEV105000 Standard lever box
10 5V10105010 With detent in position 2 and spring return LM10 5LEV205000 Lever box for M10 handlever
in neutral position LF1 5LEV105102 Lever box with adjustable flow limiter
11 5V11105000 Detent in positions neutral, 1 and 2 LEB 5LEV605000 Safety lever box, vertical configuration
12 5V12105000 Detent in positions 1 and 2 LUP 5LEV805005 Safety lever box, horizontal configuration
15 5V15105000 2 positions, detent in positions 1 and SLP 5COP105000 Witout lever box, with dust--proof plate
neutral SLC 5COP205000 Witout lever box, with endcap
16 5V16105000 2 positions, detent in positions 2 and TQ 5TEL105110 Flexible cable connection
neutral LCB 5CLO205100 Joystick lever for 2 sections operation
9BZ 5V09202010 With detent in position 1 and spring return
in neutral position 6. Complete controls page 44
Proportional hydraulic control type 8IM and ON/OFF solenoid controls
in neutral position
type 8ES and 8ESN.
11BZ 5V11202010 Detent in positions 1 and 2 and spring
return in neutral position
8K 5V08705112 With spring return in neutral position and 7. Service valves page 52
12 VDC spool solenoid lock device Port relief, anti--shock, pilot operated check and flow regulation valves.
5V08705124 As previous, 24VDC
8RM2 5V08105590 With spring return in neutral position and
12VDC electromagnetic detent in pos. 2
5V08105595 As previous, 24VDC 8. Outlet port options page 49
8MHE3(NC) 5V08106541 With spring return in neutral position and TYPE CODE DESCRIPTION
spool postioning ON/OFF electric signal AET XTAP623170 Open centre plug
circuit normally closed AEK 3XTAP522282 Closed centre plug
8MHE3(NO) 5V08106540 As previous, with circuit normally open AE 3XGIU522460* G3/8 carry--over sleeve
8MS3 5V08105553 With spring return in neutral position, AET-- L XCAR405300 With hydraulic pilot unloader valve
operation signalling in position 1 and 2, AET-- EL YCAR405305 With 12VDC electric control unloader
prearranged for centralized microswitch valve; normally open circuit
control: need KM connection kit YCAR405310 As previous 24VDC
8MG3(NO) 5V08105660 With spring return in neutral position and AET-- ELC 5CAR405330 With 12VDC electric control unloader
microswitch in positions 1 and 2 valve; normally closed circuit
8P 5V08105701 ON/OFF pneumatic kit 5CAR405331 As previous 24VDC
8EP3 5V08105735 ON/OFF 12 VDC electro--pneumatic kit AET-- LT XTAP523370 Prearranged for unloader valve, with
5V08105740 ON/OFF 24 VDC electro--pneumatic kit blanking plug
8ED3 5V08105350 ON/OFF 12 VDC electro--hydraulic kit
5V08105351 ON/OFF 24 VDC electro--hydraulic kit
9. Inlet and outlet selection * page 9
II Optional handlevers TYPE CODE DESCRIPTION
PSL 3XTAP722160 Side ports; need n.2 G 3/8 plugs, standard
TYPE CODE DESCRIPTION configuration (omit in valve description)
AL01/M8x120 170011012 For lever L: height 120 mm / 4.72 in PSA 3XTAP722160 Upper ports; need n.2 G 3/8 plugs
AL01/M10x150 170012015 For lever LM10:
height 150 mm / 5.91 in
AL08/M12x150 170013115 For joystick LCB: I ”A” and “B” ports plugs *
height 150 mm / 5.91 in TYPE CODE DESCRIPTION
G3/8 3XTAP722160 for single acting spool type 3
DAU003E 11
Inlet relief options
Direct pressure relief vave
VMD5 ( J G 3 -- 120 )
Standard setting in bar (for value see page 8)
Adjustable spring type (2, 3, 4).

Adjustment type (G, H)
Adjustment type
G: with screw H: valve set and locked

Wrench 19
42 Nm / 31 lbft Wrench 13 Cap code: 3COP117260
24 Nm / 17.7 lbft
Allen wrench 4
max. 51.5 59.5

2.03 2.34
Performance data
Spring nr. 2 (green band) Spring nr. 3 (blue band) Spring nr. 4 (red band)
400 (psi) 400 (psi) 400 (psi)

(bar) (bar) (bar)
300 4500 300 4500 300 4500
Pressure
Pressure
Pressure
200 3000 200 3000 200 3000
100 1500 100 1500 100 1500
0 0 0
0 20 40 60 0 20 40 60 0 20 40 60
Flow (l/min) Flow (l/min) Flow (l/min)
SV: relief valve blanking plug
Time response
(% ∆P)
105%
Allen wrench 10
42 Nm / 31 lbft 95%
Pressure
90%
1450 psi
100 bar
10%
Time (”)
0,05”
TIME RESPONSE
12 DAU003E
Spool options
Type 1
For special requirement, spool 1CS code 3CU1210200 suggested for flow from 15 to 30 l/min and spool 1CEX code 3CU1210230
suggested for flow up to 15 l/min, are available.
1 0 2
A B
A B
"
stroke:
T P T LC + 5.5 mm / 0.22 in P T
P→A B→T
29
10 0.35
20
1 0 2
0.39 A B
0.79 A B
T P T LC P T
142
5.59
P--A--B--T closed, with flow through line (LC) open
1 0 2
A B
A B
A
stroke:
T P T LC + 5.5 mm / 0.22 in P T
P→ B A→T
Performance data
Spool metering P→A(B) Spool metering A(B)→T

0.1 0.2 (in) 0.1 0.2 (in)
60 60
(l/min ) (l/min )
40 40
J F
Flow
Flow
F J Y
20 20
Y Qin = 45 l/min
F P(on ports) = 63bar / 900 psi
Y P(on ports) = 100bar / 1450 psi
0 0
0.0 1.0 2.0 3.0 4.0 5.0 5.5 J P(on ports) = 250bar / 3600 psi 0.0 1.0 2.0 3.0 4.0 5.0 5.5
Stroke (mm) Stroke (mm)
DAU003E 13
Spool options
Type 1A
1 0 2
A B + 5,5 mm / 0.22 in
A B
(1) "
(0)
A (2)
T P T LC P T
-- 5,5 mm / 0.22 in
P--B closed, A→T, flow through line (LC) open
Type 1B
1 0 2
A B + 5,5 mm / 0.22 in
A B
(1) "
(0)
A (2)
T P T LC P T
-- 5,5 mm / 0.22 in
P--A closed, B→T, flow through line (LC) open
Type 2
1 0 2
A B + 5,5 mm / 0.22 in
A B
(1) "
(0)
A (2)
T P T LC P T
-- 5,5 mm / 0.22 in
P closed, A--B→T, flow through line (LC) open
Type 2H
1 0 2
A B + 5,5 mm / 0.22 in
A B
(1) "
(0)
A (2)
T P T LC P T
-- 5,5 mm / 0.22 in
P closed, A--B partially open to tank,
flow through line (LC) open
14 DAU003E
Spool options
Type 3
A
1 0 2
A
"
stroke:
T P T LC + 5.5 mm / 0.22 in P T
P→A
Port B plugged
Allen wrench 6 -- 24 Nm / 17.7 lbft
A
1 0 2
A
T P T LC P T
P--B--T closed, flow through line (LC) open
1 0 2
A
A
stroke:
T P T LC -- 5.5 mm / 0.22 in P T
A→T
Performance data
Spool metering P→A Spool metering A→T

0.1 0.2 (in) 0.1 0.2 (in)
60 60
(l/min ) (l/min )
40 40
J F
Flow
Flow
Y Y
20 20
F J Qin = 45 l/min
F P(on ports) = 63bar / 900 psi
0 0
DAU003E 15
Spools
Type 5DY
It needs special body with extra machining: for information please contact Sales Deptartment.
This spool must be coupled with positioner type 13NZ (see page 36).
Also available spool with check valve on A port; type 5WY code 3CU1242320.
1 0 2 3
A B
A B
"
stroke:
T P T LC + 4.5 mm / 0.18 in P T
P→ A , B → T
1 0 2 3
A B
A B
T P T LC P T
P--A--B--T closed
1 0 2 3
A B
A B
A
stroke:
T P T LC -- 4.5 mm / 0.18 in P T
P→ B , A → T
1 0 2 3
A B
A B
AA
stroke:
T P T LC -- 9 mm / 0.35 in P T
A--B → T (float in lock position)
Performance data
Spool metering Pressure drop in position 3
Qin = 45 l/min / P(on ports) = 100 bar -- 1450 psi (last section)
0.1 0.2 (in)
60 20 (psi)
(l/min ) (bar)
B→T 15
40 200
Pressure
P→A A→T
Flow
10 A→T
P→B
20 B→T 100
5
0 0
0,0 1,0 2,0 3,0 4,0 5,0 5.5 0 15 30 45 60
Stroke (mm) Flow (l/min)
16 DAU003E
Spools options
Type 5PY
It needs special body with extra machining: for information please contact Sales Department.
This spool must be coupled with positioner type 13QN (see page 36) and 13QNMG3 (see page 37).
3 1 0 2
A B
A B
""
stroke:
T P T LC + 9 mm / 0.35 in P T
3 1 0 2
A B
A B
"
stroke:
T P T LC + 4.5 mm / 0.18 in P T
P→ A , B → T
3 1 0 2
A B
A B
T P T LC P T
P--A--B--T closed,
with flow through line (LC) open
3 1 0 2
A B
A B
A
stroke:
T P T LC -- 4.5 mm / 0.18 in P T
P→ B , A → T
Performance data
0.1 0.2 (in)
60 20 (psi)
(l/min) (bar)
A→T 15
40 200
Pressione
P→A(B)
B→T
Flow
10
A(B)→T
20 100
5
0 0
0,0 1,0 2,0 3,0 4,0 5,0 5.5 0 15 30 45 60
Stroke (mm) Portata (l/min)
DAU003E 17
Spools
Type 8
This spool must be coupled with positioner type 13FZ (see page 37).
1 0 2 3
A B
A B
"
stroke:
T P T LC + 4.5 mm / 0.18 in P T
P→ A , B → T
1 0 2 3
A B
A B
T P T LC P T
P--A--B--T closed flow through line (LC) open

1 0 2 3
A B
A B
A
stroke:
T P T LC -- 4.5 mm / 0.18 in P T
P→ B , A → T
1 0 2 3
A B
A B
AA
stroke:
T P T LC -- 7.5 mm / 0.30 in P T
P → A--B (regenerative)
Performance data
Spool metering Pressure drop in positione 3
0.1 0.2 (in)
60 20 (psi)
(l/min ) (bar)
15
40 200
Pressure
Flow
10 A→B
A(B)→T P→A(B)
P→B
20 100
5
0 0
0.0 1.0 2.0 3.0 4.0 5.0 5.5 0 15 30 45 60
18 DAU003E
Spool options
Type 8F
1 0 2
A B
A B
"
stroke:
T P T LC + 5.5 mm / 0.22 in P T
1 0 2
A B
A B
T P T LC P T
1 0 2
A B
A B
A
stroke:
T P T LC -- 5.5 mm / 0.22 in P T
P→ B , A → T
Performance data
Qin = 45 l/min / P(on ports) = 100 bar -- 1450 psi (in first section)
0.1 0.2 (in)
60 20 (psi)
(l/min ) (bar)
15
40 200
Pressure
Flow
10 B→A
P→A
20 100
A→T P→B 5
0 0
0.0 1.0 2.0 3.0 4.0 5.0 5.5 0 15 30 45 60
DAU003E 19
”A” side spool positioners
With spring return in neutral position

8 kit
It’s supplied with standard spring type D (see force--stroke diagram) and available with lighter spring type C (8MC code: 5V08205000)
or heavier type E (8ME code: 5V08405000).
Force--stroke diagram
- 0.2 - 0.1 0 0.1 0.2 (in)
1 0 2 300 (lbf)
(N) E 60
Allen wrench 4 200
D 40
6.6 Nm / 4.9 lbft
100 C 20
Force
Allen rench 5 0 0
9.8 Nm / 7.2 lbft
--100 C - 20
--200
D - 40
E - 60
--300
--6 --5 --4 --3 --2 --1 0 1 2 3 4 5 6
36.5 Stroke (mm)
1.44
8D kit
Spool end joint code XPER315400, is available on request in order to screw onto pin.
Allen wrench 4 1 0 2
6.6 Nm / 4.9 lbft Spool end joint dimensions
Wrench 9
9.8 Nm / 7.2 lbft
M6
12
15
4
0.59
0.47
0.16 10 20
0.39 0.79
8
0.31
M6
36.5
18
8
0.31
1.44
0.71
44 40
1.73 1.57
8D2 kit
1 0 2
Allen wrench 4
6.6 Nm / 4.9 lbft
Wrench 9
9.8 Nm / 7.2 lbft
M8
40 36.5
1.57 1.44
84
3.31
20 DAU003E
“A” side spool positioners

8F2 kit
Allen wrench 5 Allen wrench 4 1 0 2

9.8 Nm / 7.2 lbft 6.6 Nm / 4.9 lbft
Wrench 13
24 Nm / 17.7 lbft
Allen wrench 4
M8x1
36.5
1.44
51.5
2.03
19 kit
1 0 Force--stroke diagram
0.1 0.2 (in)
300 (lbf)
Allen wrench 4 (N) 60
6.6 Nm / 4.9 lbft 200 40
100 20
Force
Allen wrench 5
0 0
9.8 Nm / 7.2 lbft
--100 - 20
--200 - 40
- 60
--300
36.5 0 1 2 3 4 5 6
1.44 Stroke (mm)
20 kit
- 0.2 - 0.1 (in)
300 (lbf)
(N) 60
Allen wrench 4
200 40
6.6 Nm / 4.9 lbft
100 20
Allen wrench 5
Force
9.8 Nm / 7.2 lbft 0 0

--100 - 20
--200 - 40
- 60
--300
36.5 --6 --5 --4 --3 --2 --1 0
1.44 Stroke (mm)
DAU003E 21
With detent
9 kit 10 kit
1 0 2 1 0 2
Allen wrench 4
Allen wrench 4
6.6 Nm / 4.9 lbft
6.6 Nm / 4.9 lbft
Allen wrench 5
Allen wrench 5 9.8 Nm / 7.2 lbft
9.8 Nm / 7.2 lbft
45.5
45,5 41
1.79 1.61
Operating features Operating features
Locking force (from pos. 0 to 1) . . . : 150 N / 33.7 lbf ±10% Locking force (from pos. 0 to 2) . . . : 150 N / 33.7 lbf ±10%
Release force (from pos. 1 to 0) . . . : 140 N / 31.5 lbf ±10% Release force (from pos. 2 to 0) . . . : 140 N / 31.5 lbf ±10%
11 kit 12 kit
1 0 2 1 0 2
Allen wrench 4
Allen wrench 4
6.6 Nm / 4.9 lbft
6.6 Nm / 4.9 lbft
Allen wrench 5 Allen wrench 5
9.8 Nm / 7.2 lbft 9.8 Nm / 7.2 lbft
36.5 36.5
36,5
1.44 1.44
Locking and release force . . . . . . . . : 120 N / 27 lbf ±10% Locking and release force . . . . . . . . : 100 N / 22.5 lbf ±10%
15 kit 16 kit
1 0 0 2

6.6 Nm / 4.9 lbft 6.6 Nm / 4.9 lbft
Allen wrench 5
Allen wrench 5
9.8 Nm / 7.2 lbft
9.8 Nm / 7.2 lbft
36.5 36.5
1.44 1.44

Locking and release force . . . . . . . . : 100 N / 22.5 lbf ±10% Locking and release force . . . . . . . . : 100 N / 22.5 lbf ±10%
22 DAU003E
With detent and sprimg return to neutral position from either directions
9BZ kit
1 0 2 Port B Port A
2 0 1
- 0.2 - 0.1 0 0.1 0.2 (in)
300 (lbf)
(N) 60
- 0.22
0.13
0.22
Allen wrench 4 200 40
6.6 Nm / 4.9 lbft 100 20
Force
0 0
--100 - 20
Detent area - 40
--200
- 5.5
3.3
5.5
- 60
72.5 --300
2.85 --6 --5 --4 --3 --2 --1 0 1 2 3 4 5 6
Stroke (mm)
Allen wrench 5
9.8 Nm / 7.2 lbft Locking force: 120 N / 27 lbf ±10% / Release force: 230 N / 51.7 lbf ±10%
10BZ kit
1 0 2 Port B Port A
2 0 1
- 0.2 - 0.1 0 0.1 0.2 (in)
300 (lbf)
(N) 60
- 0.22
- 0.13
0.22
Allen wrench 4 200
40
6.6 Nm / 4.9 lbft 100 20
Force
Detent area
0 0
--100 - 20
--200 - 40
- 5.5
- 3.3
5.5
- 60
72.5 --300
2.85 --6 --5 --4 --3 --2 --1 0 1 2 3 4 5 6
Stroke (mm)
Allen wrench 5
11BZ kit
1 0 2 Port B Port A
2 0 1
- 0.2 - 0.1 0 0.1 0.2 (in)
(lbf)
300
(N) 60
- 0.19
- 0.22
0.13
0.22

6.6 Nm / 4.9 lbft 100 20
Force
Detent area Detent area

0 0
--100 - 20
--200 - 40
- 5.5
- 3.3
3.3
5.5
- 60
72.5 --300
2.85 --6 --5 --4 --3 --2 --1 0 1 2 3 4 5 6
Stroke (mm)
Allen wrench 5
DAU003E 23
Solenoid lock device type 8K

With spring return and spool electromechanical lock in neutral position; when coil is feeded the spool can be moved.
Operating features
ACTUATOR
1 0 2 Lock stroke . . . . . . . . . . . . . . . . . . . . . : 3.5 mm / 0.14 in
COIL
Depending on model: see following features
Coil with ISO4400 connector
Wrench 24
Allen wrench 4 9.8 Nm / 7.2 lbft
6.6 Nm / 4.9 lbft
112.5
4.43
Wrench 10
9.8 Nm / 7.2 lbft Nom. voltage tolerance . . . . . . . . : ±10%
Power rating . . . . . . . . . . . . . . . . . : 18 W
Nominal current . . . . . . . . . . . . . . . : 1.58 A -- 12 VDC
Allen wrench 5
: 0.81 A -- 24VDC
9.8 Nm / 7.2 lbft
Coil insulance . . . . . . . . . . . . . . . . : Class F
Weather protection . . . . . . . . . . . . : IP65
Duty cycle . . . . . . . . . . . . . . . . . . . : 100%
Allen wrench 4
6.6 Nm / 4.9 lbft 22 Coil with Deutsch DT connector
0.87
71.5
2.82
NOTE -- The kit control must be turned at 180°. when pilot

operated check valves are fitted.
Nom. voltage tolerance . . . . . . . . : ±10%

Power rating . . . . . . . . . . . . . . . . . : 22 W
COMPLETE CONTROLS CODES
: 0.95 A -- 24VDC
CONNECTION TYPE
Coil insulance . . . . . . . . . . . . . . . . : Class H
ISO4400 Deutsch DT Packard M-- Pack Weather protection . . . . . . . . . . . . : IP65
CONTROL TYPE Duty cycle . . . . . . . . . . . . . . . . . . . : 100%
Voltage 8K 8K4 8K6
12 VDC 5V08705112 5V08705412 5V08705612 Coil with Packard M-- Pack connector
24 VDC 5V08705124 5V08705424 5V08705624
634
Need 25
connector C02 C19 C20
(see page 129)
Nom. voltage tolerance . . . . . . . . : ±10%

Power rating . . . . . . . . . . . . . . . . . : 18 W
: 0.81 A -- 24VDC
Coil insulance . . . . . . . . . . . . . . . . : Class F
Weather protection . . . . . . . . . . . . : IP65
Duty cycle . . . . . . . . . . . . . . . . . . . : 100%
24 DAU003E
“A” side spool positioner
Solenoid lock device type 8K

More configurations and spare parts
It’s possible to obtain further configurations of complete control, using the K kit, coils and 3 positions “A” side spool positioner, as
following draw: for information contact Sales Department.
COILS CODES
Coil
CONNECTION TYPE
Voltage ISO4400 Deutsch DT Packard M-- Pack
12 VDC 2X4300012 2X4300014 YSOL300013
24 VDC 2X4300024 2X4300026 YSOL300025
Kit K
Fitted with actuator:
code 5KIT810500
3 positions “A” side spool

positioner type 9B, 10B, 11B.
(see page 23)
DAU003E 25
Electromagnetic detent type 8RM2

With electromagnetic detent in position 2 and spring return to neutral position.
1 0 2
Solenoid kit with connector

600
23.6 Notch 1.2 mm / 0.047 in
6.6 Nm / 4.9 lbft
Wrench 11 -- 9.8 Nm / 7.2 lbft
Operating features
COIL
Nominal voltage . . . . . . . . . . . . . . . : 12 / 24 VDC ± 10%
Power rating . . . . . . . . . . . . . . . . . . : 5,5 W
Resistance (20 °C) . . . . . . . . . . . . . : 26,5 / ??? Ohm
Min unlocking force . . . . . . . . . . . . . : 45 N / 49.5 lbf
Duty cycle . . . . . . . . . . . . . . . . . . . . : 100%
88.5
3.48
108
4.25
Allen wrench 4 -- 6.6 Nm / 4.9 lbft
COMPLETE CONTROLS CODES Coil with Deutsch DT Coil with AMP Fastin-- Faston
connection connection
CONNECTION TYPE
600 200
Deutsch DT AMP Packard M-- Pack 23.6 7.87
CONTROL DESCRIPTION
Voltage 8RM2 8RM2A(200)
12 VDC 5V08105590 5V08105591 5V08105593
24 VDC 5V08105595 5V08105596 5V08105598
Need
connector C19 C21 C20
(see page 129)
COILS CODES
CONNECTION TYPE
Voltage Deutsch DT AMP Packard M-- Pack Coil with Packard M-- Pack
12 VDC YSOL532455 YSOL532452 YSOL532451 connection
24 VDC YSOL532456 YSOL532458 YSOL532457
374
14.7
26 DAU003E
8MHE3 kit: with spring return in neutral position and spool positioning ON/OFF signal
This module supplies two different ON/OFF signals, related to the direction of the spool.
It has two separate contacts which can be normallyopen or normally closed.
Connection DIN43650/C
(needs connector type C11, see page 129)
Notch -- 6.6 Nm / 4.9 lbft Connector wiring

Wrench 10
Wrench 5 9.8 Nm / 7.2 lbft
6.6 Nm / 4.9 lbft
2 3
38.5
1.52
Position 2 Position 1
signal signal
4 1
44.5
1.75 Operating features
81 Power supply range : from 3 da 28 VDC
3.19 Max. output current . : 500 mA
Wrench 5 See view A Weather protection . : IP65
9.8 Nm / 7.2 lbft
8MHE3(NC) kit 8MHE3(NO) kit

4 1 2 3 4 1 2 3
Configuration with Configuration with

normally closed circuit 1 0 2 normally open circuit 1 0 2
View A View A
Mobile contact Mobile contact

Fixed contact Fixed contact
Ouput signal with NC circuit Ouput signal with NO circuit

Tolerance range Tolerance range
(VDC) - 0.2 - 0.1 0 0.1 0.2 (in) (VDC) - 0.2 - 0.1 0 0.1 0.2
12
100% 12
100%
Voltage
Voltage
0 0
--6 --5 --4 --3 --2 --1 0 1 2 3 4 5 6 --6 --5 --4 --3 --2 --1 0 1 2 3 4 5 6
DAU003E 27
8MS3 kit: with centralized control for microswitch

Assembly example
It’s shown an assembling on 2 section directional control valve, complete with connection kit KM.
25.4
1 Bracket for 5MIC100
1
M3 microswitch
Microswitch on 0.04
request (see page 25) n.2 threads
0.32
8
2.28
58
Allen wrench 2.5
Rocker arm to 6.6 Nm / 4.9 lbft
actuate microswitch
Allen wrench 2.5
6.6 Nm / 4.9 lbft
A1 B1 A2 B2
120
1750
Es.: SD5/2--P(JG3--120)/18MS3L/18MS3L/AET -- KM 2 S 51
51 = with bracket for M51 (IP51) microswitch fixing
Assembling kit
67 = with bracket for M67 (IP67) microswitch fixing
S = bracket placed on left

Nr. of working sections
D = bracket placed on right
28 DAU003E
8MS3 kit: with centralized control for microswitch

The spool positioner is composed of actioning pin 1, bushes 2 and return spring 3. 8MS3 kit
The remaining items (cap, rocker arm, bracket , rod ecc..) are components of KM con- microswitch operation in
nection kit, which depends on nr of controlled section. positions 1 and 2
Allen wrench 2.5

6.6 Nm / 4.9 lbft
1 0 2
Allen wrench 4 2
6.6 Nm / 4.9 lbft
Other configurations
3
8MS1 kit
microswitch operation in
1 position 1
58.3 1 0 2
2.29 Notch 1.5 mm / 0.06 in
9.8 Nm / 7.2 lbft
8MS2 kit
KM kit ordering codes microswitch operation in
The codes below represent the kit with bracket for IP51 position 2
microswitch, assembled on the left
For other codes or information contact Sales Department.
1 0 2
TYPE CODE DESCRIPTION
KM1S51 5KM1S5102 Kit for 1 section
KM2S51 5KM2S5102 Kit for 2 sections
Microswitches for 8MS kits

It’s complete with rubber cover and mounting screws: to order separately
M51 code: 5MIC100 M67 code: 5MIC200
Dedicated bracket is needed for the assembly

6
∅ code: 3FLA225052 58.2
0.24
25.5 14 2.29
0.28
7
1.00 0.55 33 6
1.30 0.24
∅
M3
2.52
M4
64
55.5
2.19
30.2
1.19
27.1
1.07
Stroke
21 4 Stroke
0.10
2.5
0.83 0.16 18 4
1.5
0.06
0.71 0.16
68
2.68
Max. current / voltage . . . . . . . . . . . . . : 15 A / 480 VAC Max. current / voltage . . . . . . . . . . . . . : 5 A / 250 VAC
: 0.25 A / 250 VDC : 0.25 A / 230VDC
Weather protection . . . . . . . . . . . . . . . : IP51 Weather protection . . . . . . . . . . . . . . . : IP67
DAU003E 29
With microswitch type 8MG3(NO)

With spring return in neutral position and microswitch operated in both directions.
Also available 8MG1(NO) configuration (microswitch operated in position 1) and 8MG2(NO) configuration (microswitch operated in
position 2); dimensions are the same of 8MG3 configuration.
Same configurations are available with normally closed (NC) contact.
Microswitch with connector

8MG3(NO) kit
Wrench 22
42 Nm / 31 lbft
Wrench 10 1 0 2
9.8 Nm / 7.2 lbft
Allen wrench 4
6.6 Nm / 4.9 lbft
Other configurations
8MG1(NO) kit 8MG2(NO) kit
66,5 1 0 2 1 0 2
Allen wrench 5 Allen wrench 4 -- 6.6 Nm / 4.9 lbft
9.8 Nm / 7.2 lbft
COMPLETE CONTROLS CODES

Operating features
CONTROL TYPE MICROSWITCH
Need
connector type Mechanical life . . . . . . . . . . . : 5x105 operations
Contact 8MG3 8MG2 8MG1
Electrical life (resistive load) : 105 oper. -- 7A / 13.5VDC
NO 5V08105660 5V08105680 5V08105670 C07 see page : 5x104 oper -- 10A / 12VDC
NC 5V08105662 5V08105682 5V08105672 C17 129 : 5x104 per -- 3A / 28VDC

It’s possible to obtain further configurations of complete control, using the MG kit, microswitches and 3 positions “A” side spool posi-
tioner, as following draw.
With NO contact With NC contact
code: 4MIC730 code: 4MIC740
Microswitch 84,5 128

3.33 5.04
PACKARD W--PACK PACKARD W--PACK

female connector male connector with
with male end female end
Kit MG3 Kit MG1 Kit MG2

code: 5KIT820500 code: 5KIT820501 code: 5KIT820502
3 positions “A” side spool Kit MG
positioner type 9B, 10B, 11B.
(see page 23)
30 DAU003E
ON/OFF pneumatic kit type 8P

With spring return to neutral position.
1 0 2
Wrench 11 V1 V2
9.8 Nm / 7.2 lbft NPT 1/8” -- nr.2 thread
51.5
Allen wrench 4 2.03
6.6 Nm / 4.9 lbft V2
0.91
23
Operating features
Pilot pressure . . . . . . . . . . . . . . . . . . . : min. 5.5 bar / 80 psi
V1
: max. 10 bar / 145 psi
118
4.64
Wrench 10 Allen wrench 4
9.8 Nm / 7.2 lbft 6.6 Nm / 4.9 lbft
DAU003E 31
ON/OFF electropneumatic kit type 8EP3
Wrench 14 -- 9.8 Nm / 7.2 lbft Scheme

Pg9 43 57 V1 V2
1.69 2.24
1 0 2
113.5
4.47
Scheme ISO 1219

V1 V2
1 0 2
0.24
6
1.65
42
V1 V2
119
4.68
Allen wrench 4 Wrench 9 Allen wrench 4 -- 6.6 Nm / 4.9 lbft
6.6 Nm / 4.9 lbft Special wrench -- 9.8 Nm / 7.2 lbft
Wrench 13
24 Nm / 17.7 lbft
COMPLETE CONTROL CODES Operating features

CONTROL
CONNECTION TYPE Pilot pressure . . . . . . . . . . . . . . : 6 bar / 87 psi
ISO6952 Flying leads : (max.10 bar / 145 psi)
COIL
CONTROL TYPE
Nominal voltage tolerance . . . . : ±10%
Voltage 8EP3 8EP35 Power rating . . . . . . . . . . . . . . . : 8 W
12 VDC 5V08105735 5V08105736 Nominal current . . . . . . . . . . . . . : 0.67 A -- 12 VDC
24 VDC 5V08105740 5V08105741 : 0.33 A -- 24VDC
Need Coil insulation . . . . . . . . . . . . . . : Class F
C01 Weather protection . . . . . . . . . . : IP65
connector type /
(compreso)
(see page 129) Duty cycle . . . . . . . . . . . . . . . . . : 100%
COIL CODES Coil with ISO6952 Coil with flying leads

connector
200
CONNECTION TYPE
Voltage 7.87
ISO6952 Flying leads*
12 VDC 2X4000013 2XB1000120000
24 VDC 2X4000025 2XB1000240000
* Several type of connectors can be wired on request
32 DAU003E
ON/OFF electrohydraulic kit type 8ED3

With external pilot and drain.
Allen wrench 4 -- 6,6 Nm / 4.9 lbft Scheme
1
139 L
5.47 V
42 59
1.65 2.32
6.6 Nm
4.9 lbft
1 0 2
Coil Scheme ISO 1219

Solenoid valve:
wrench 24 -- 9.8 Nm / 7.2 lbft
1 0 2
133
5.24
Wrench 10 -- 24 Nm / 17.7 lbft
Special wrench -- 9.8 Nm / 7.2 lbft

Collector
V L
116
4.57
133
5.24
Wrench 10 Allen wrench 4 -- 6.6 Nm / 4.9 lbft
Operating features
CONTROL
Pilot pressure . . . . . . . . . . . . . . . . . . . : min. 10 bar / 145 psi
: max. 50 bar / 725 psi
Max backpressure on drain L . . . . . . : 25 bar / 360 psi
COIL
Nominal voltage tolerance . . . . . . . . . : ±10%
Power rating . . . . . . . . . . . . . . . . . . . . : 21 W
Nominal current . . . . . . . . . . . . . . . . . . : 1.75 A -- 12 VDC / 0.87 A -- 24VDC
Coil insulation . . . . . . . . . . . . . . . . . . . : Class F
Weather protection . . . . . . . . . . . . . . . : IP65
Duty cycle . . . . . . . . . . . . . . . . . . . . . . : 100%
COMPLETE CONTROL CODES
CONNECTION TYPE
AMP JPT
ISO4400 Deutsch DT
without diode with diode
CONTROL TYPE
Voltage 8ED3 8ED32 8ED32D 8ED34
12 VDC 5V08105350 5V08105250 5V08105280 5V08105450
24 VDC 5V08105351 5V08105251 5V08105281 5V08105451
Need
connector type C02 C08 C08 C19
(see page 129)
DAU003E 33
COIL CODES
CONNECTION TYPE
AMP JPT
ISO4400 Deutsch DT
Voltage without diodo with diodo
12 VDC 2XB1400121100 2XB1400121200 2XB1400121210 2XB1400120400
24 VDC 2XB1400241100 2XB1400241200 2XB1400241210 2XB1400240400
Coil with Coil with Coil with Deutsch DT connection

ISO4400 connection AMP JPT connection
170
6.69
Collector kit for external pilot and drain
A1 B1 A2 B2
L
V
V L
149.5
20 bar
5.89
290 psi
T
Collector
P T
120
1750
COLLECTOR KIT CODES
Type Code * Description

Description example:
KE1S0 5KE1S00030 Kit one section
SD5/2--P(JG3--120)/18ED3L/18ED3L/AET--KE2S0--24VDC
KE2S0 5KE2S00230 Kit for 2 sections
(*) codes are referred to BSP thread
34 DAU003E

Collector kit with pilot and drain lines
The kit is made of collector, VRP pressure reducing valve and pipes.
28 136 VRP
5.35 Wrench 19 A1 B1 A2 B2
1.10
Allen wrench 6 24 Nm / 17.7 lbft
Collector
24 Nm / 17.7 lbft
VRP Code:
2S100808VAL21 Drain
149.5
5.89
T
Wrench 17
Wrench 22
24 Nm / 17.7 lbft
Inlet line P
P T
VRC
120
1750
VRC backpressure
Wrench 22 valve (not included)
35
24 Nm / 17.7 lbft
1.38
COLLECTOR KIT CODES
SD5/2--P(JG3--120)/18ED3L/18ED3L/VRC--KE2R3--24VDC
Tipo Code * Description
Operating features KE1R0 5KE1R30230 Kit one section
VRP VALVE KE2R0 5KE2R30230 Kit for 2 sections
Output pressure . . . . . . . . . . . . . . . . . : 20 bar / 290 psi KE3R0 5KE3R30230 Kit for 3 sections
Max flow . . . . . . . . . . . . . . . . . . . . . . . : 8 l/min
KE4R0 5KE4R30230 Kit for 4 sections
Filtering . . . . . . . . . . . . . . . . . . . . . . . . : 80 µ
(*) Codes are referred to BSP thread
VRC valve: code X003600010

Valve assembled on flow through passage provides pilot pressure to the actuator.
Pressure drop P→T

Wrench 22 40
(psi)
42 Nm / 31 lbft (bar)
30
Wrench 22 400
Pressure
24 Nm / 17.7 lbft 20
200
10
20
0.79 0
0 15 30 45
Flow (l/min)
DAU003E 35
Particular positioner kits for special spools

13NZ kit
Detent in 4th position with spool in:available only for spool type 5DY (see page 16).
1 0 2 3 Force--stroke diagram
Floating Port B Port A

3 2 0 1
- 0.3 - 0.2 - 0.1 0 0.1 (in)
Allen wrench 4
400 (lbf)
6.6 Nm / 4.9 lbft
- 0.18
0.27
- 0.27
(N)
60
Wrench 6 200
9.8 Nm / 17.7 lbft 30
Force
0 0
- 30
--200
- 6.8 - 60
- 4.5
4.5
72.5 --400
2.85 --9 --8 --7 --6 --5 --4 --3 --2 --1 0 1 2 3 4 5
Special body kit Stroke (mm)
Detent area
Locking force: 280 N / 63 lbf ±10%
Release force: 300 N / 67.4 lbf ±10%
13QN kit
Detent in 4th position with spool out:available only for spool type 5PY (see page 17).
Port B Port A Floating

2 0 1 3
- 0.1 0 0.1 0.2 0.3 (in)
Allen wrench 4
400 (lbf)
6.6 Nm / 4.9 lbft
- 0.18
0.18
(N)
60
0.27
Wrench 6 200
9.8 Nm / 17.7 lbft 30
Forza
0 0
- 30
--200
- 60
- 4.5
4.5
6.8
72.5 --400
2.85 --5 --4 --3 --2 --1 0 1 2 3 4 5 6 7 8 9
Detent area
36 DAU003E

13FZ kit
4th position with spool in and spring return to neutral position.
Avalable only for spool type 8 (see page 18).
1 0 2 3 Regenerative Port B Port A

3 2 0 1
- 0.3 - 0.2 - 0.1 0 0.1 (in)
Allen wrench 4 400
(N) (lbf)
6.6 Nm / 4.9 lbft
60
Wrench 6 200
30
9.8 Nm / 17.7 lbft
Force
0 0
- 30
--200
- 60
7,5
4,5
4,5
72.5 --400
2.85 --8 --7 --6 --5 --4 --3 --2 --1 0 1 2 3 4 5
Stroke (mm)
Special body kit
13QNMG3(NO) kit
Detent in 4th position with spool out, spring return to neutral position and microswitch operation in both directions.
The microswitch can be configured with NO (normally open) or NC (normally closed) contact
Available only for spool type 5PY (see page 17).
Microswitch with
connector
Wrench 22 -- 42 Nm / 31 lbft
3 1 0 2
Allen wrench 4
6.6 Nm / 4.9 lbft
Operating features
MICROSWITCH
Mechanical life . . . . . . . . . . . . . : 5x105 operations
Electric life (resistive load) . . . . : 105 operations -- 7A / 13.5VDC
: 5x104 operations -- 10A / 12VDC
102.5 : 5x104 operations -- 3A / 28VDC
4.04
9.8 Nm / 7.2 lbft 6.6 Nm / 4.9 lbft
COMPLETE CONTROL CODES CODICI MICROINTERRUTTORI DI RICAMBIO
Contact type Needs connector Microswitch kit with NO contact Microswitch kit with NC contact
type code: 4MIC730 code: 4MIC740
5V13405660 NO C07 see page 84.5 128
129 3.33 5.04
5V13405661 NC C17
Female PACKARD Male PACKARD

W--PACK connector W--PACK connector
with male ends with female ends
DAU003E 37

With electromechanical lock
The positioners for special spools (13NZ, 13QN, 13FZ), are also available with spool electromechanical lock in neutral position; if
coil is excited the spool can be operated.
For kit K and coils features and dimensions, see page 24: for informations contact Sales Department.
Coil CODICI BOBINE
CONNECTION TYPE
12 VDC 2X4300012 2X4300014 YSOL300013
24 VDC 2X4300024 2X4300026 YSOL300025
Need
connector type C02 C19 C20
(see page 129)
Kit K
Complete actuator kit:
13NZ positioner kit code 5KIT810500
(see page 36)
for spool type 5DY
Special body kit depending

on used spool: for informa-
tion contact Sales Depart-
13QN positioner kit ment.
(see page 36)
for spool type 5PY
13FZ positioner kit

(see page 37)
for spool type 8
38 DAU003E
”B” side options
Lever control
Type L
Alluminium with protection boot lever pivot box; it can be rotated 180° (execution L180).
(**) (*) 1 0 2
Vertical handlever Horizontal handlever

assembly assembly
M8 65.5 Execution L180

2.58
53.7
2.11
0.79
20
0.96
24.5
20
0.79 Allen wrench 4
29.2
1.15
44 1.61
6.6 Nm / 4.9 lbft
41
1.73
NOTE (*) -- With spool type 5DY (see page 16)

(**) -- With spool type 5PY (see page 17)
Type LM10 Type LF1
1 0 2 1 0 2
M10
M8
M10 M8
Allen wrench 2.5

71.5
2.82
65.5
2.58
53.7
2.11
2.13
54
0.79
0.79
20
20
24.5
0.96
24.5
0.96
20 20
0.79 Allen wrench 4 0.79
44 6.6 Nm / 4.9 lbft 44
1.73 1.73
max 66 Wrench 13
2.60 24 Nm / 17.7 lbft
DAU003E 39
“B” side options
Special lever controls

Safety levers with lock in neutral complete with handlever; lift handlever knob to operate.
Type LEB
To be used with body valves without auxiliary relief valves flanged on the working ports.
Available with execution LEBS, code 5LEV605100, for configurations with auxiliary valves type BP and BPS: it operates floating
spool (4 positions) only by pulling the lever, with spool in (type 5DY).
1 0 2
LEB LEBS
58.5
2.30
0.26
0.20
6.7
lock release
lock release
Stroke for
5
Stroke for
Locking bush
Wrench 13
24 Nm / 17.7 lbft
9.25
235
Wrench 13
24 Nm / 17.7 lbft
51.5
2.03
Allen wrench 4
0.79
6.6 Nm / 4.9 lbft

20
24.5
0.96
20 20
0.79 Allen wrench 4 0.79
44 6.6 Nm / 4.9 lbft 52.8
1.73 2.08
40 DAU003E
Special lever controls

Type LUP
Available as LUP(R150) configuration, with lenght L = 150 mm / 5.91 in and red knob: code 5LEV805010.
L = 219
8.62
20 65
0.79 2.56
M8
0.83
21
Standard black knob
53.7
2.11
Wrench 13 12
0.47 Stroke to unlocking
24 Nm / 17.7 lbft
Locking bush
Allen wrench 4
6.6 Nm / 4.9 lbft
52.8
2.08
Controls arrangement
Type SL Type SLP Type SLC
1 0 2 1 0 2 1 0 2
Allen wrench 8
Allen wrench 4 3 Nm / 2.2 lbft
6.6 Nm / 4.9 lbft
22
0.87 9 68.5
8 2.70
0.35
0.32
0.59
15
Mechanical control with dust--proof Protection cap usable with pneumatic,

9H8
+0.00866 plate. electro--pneumatic, and electro--hy-
0.35 0
draulic spool positioners.
DAU003E 41
TQ cable remote control kit

Waterproof cap prearranged for remote control with flexible cable.
1 0 2

Flexible cable
81
3.19
NOTE -- For more information about remote cable control, require appropriate documentation.
Connection example
SCF031 remote control

CD flexible cable
TQ kit
SD5/2 directional control

valve without lever boxes
NOTE -- For best efficiency, “A” side positioner with spring return type C is suggestedo (see page 20)
42 DAU003E
LCB mechanical joystick for two sections control

Execution LCB4
1 0 2
2nd section spool Pivot

Wrench 13 1 0 2
1st section spool 24 Nm / 17.7 lbft
9.8 Nm / 7.2 lbft

NOTE -- The handlever must be ordered separately (see page 11).
Dimensions and movement scheme

Execution LCB1 Execution LCB2
pivot placed down on the left pivot placed down on the right
1st section axis 2nd section axis
spool axis
B1 B2
B1--A2 B1--B2 B2--B1 B2--A1
A2 A1
2.83
B2 B1
72
1.42
36
21.5
0.85
A1--A2 A1--B2 A2--B1 A2--A1

A1 A2
M12
10 27 76
0.39 1.06 2.99
Execution LCB3 Exection LCB4

pivot placed above to the left pivot placed above on the right
A1 A2
A1--A2 A1--B2 A2--B1 A2--A1
A2 B2 B1 A1
1.42
36
B1--A2 B1--B2 B2--B1 B2--A1

B1 B2
1.5
0.06
NOTE -- Don’t use with spool type 5DY.
DAU003E 43
Complete controls14.
8ESN solenoid control

Direct control by double solenoid with spring return to neutral position, available with emergency manual override.
It’s necessary special spool and standard body (body kit without spool seals).
Due to the large dimension, it’s not possible to assembly more than one control consecutively, except SD5/2--P and SD5/3--P that
have special bodies with bigger centre--to--centre.
SD5 / 1 -- P (JG3-- 120) / 1 8ESN LES / AET - 24VDC
1. 2. 3. 4. 5.
3.
5.
4.
LES
1.
2. CAE
1. Body kit *
SD5/1-- P 5KC1193100 1 section, standard body
SD5/2-- PS 5KC1223003 2 sections, special body
SD5/3-- PS 5KC1243006 3 sections, special body
4. “B” side options
2. Spools options TYPE CODE DESCRIPTION
TYPE CODE DESCRIPTION LES 5LEV105410 Safety lever pivot box for manual
1(ESN) 3CU1210036 Double acting, 3 positions, with A and B operation
closed in neutral position CAE 5COP205100 Endcap
2(ESN) 3CU1225036 Double acting, 3 positions, with A and B
open to tank in neutral position
5. Solenoid
3. Connection kit 10.5VDC XSOL314310 Nominal voltage 10.5VDC
TYPE CODE DESCRIPTION 12VDC XSOL314312 Nominal voltage 12VDC
8ESN 5V08009 For solenoid joint, with spring return in 24VDC XSOL314324 Nominal voltage 24VDC
neutral position 192VDC XSOL314192 Nominal voltage 192VDC;
(for 220 VAC supply)
NOTE (*) -- Codes are referred to BSPthreads.
44 DAU003E
Complete controls
8ESN solenoid control
8ESNLES kit
Electric wiring example with safety lever pivot box
1 0 2
2
3
1 8ESNCAE kit
with encadp
Connector 1 0 2
P⇒B P⇒A
A⇒T B⇒T
-- +
To battery
Operating features
CONTROL
Internal leakage A(B)→T
(∆p = 100 bar -- 1450 psi / T = 40°C) : max. 15 cm3/min -- 0.91 in3/min
COIL
Manual operation:
Power rating . . . . . . . . . . . . . . . . . . . . : 65 W
lift the bush to lever
Coil insulance . . . . . . . . . . . . . . . . . . . : class H unlocking
Duty cycle . . . . . . . . . . . . . . . . . . . . . . : 100%
LES
Allen wrench 4
6.6 Nm / 4.9 lbft
Connection ISO4400
(needs C03 connector for VDC supply or C05
connector for VAC supply; see page 129)
Wrench 24
24 Nm / 17.7 lbft
Wrench 14
9.8 Nm / 7.2 lbft
2 Allen wrench 4
W1 1
W3 6.6 Nm / 4.9 lbft
68.5
2.70
Allen wrench 4 CAE

9.8 Nm / 7.2 lbft Spools: wrench 13
172.5
6.79
32
1.26
Allen wrench 4
6.6 Nm / 4.9 lbft
DAU003E 45
Complete controls14.
8ES solenoid control

Solenoid direct control with spring return to neutral position.
It needs special spools and standard body (body kit without seals on spool).
Esempio di descrizione:
SD5 / 1 -- P (JG3-- 120) / 1 8ES3 4 / AET - 24VDC
1. 2. 3. 4. 4.
4.
I
8ES3
8ES2
3. 3.
8ES3 2.
8ES1
3.
8ES2 3.
1. 4.
8ES1
1. Body kit * 3. Control kit

SD5/1-- P 5KC1193100 1 section 8ES1 5V08024 Single acting P→A, with spring return to neutral
SD5/2-- P 5KC1223100 2 sections position
SD5/3-- P 5KC1243100 3 sections 8ES2 5V08024 Single acting P→B, with spring return to neutral
SD5/4-- P 5KC1273100 4 sections position
SD5/5-- P 5KC1313100 5 sections 8ES3 5V08025 Double acting, with spring return to neutral position
SD5/6-- P 5KC1353100 6 sections
SD5/7-- P 5KC3E3100 7 sections
4. Coils
2. Spool options With ISO4400 connector
TYPE CODE DESCRIPTION 10.5VDC 4SOL512011 Nominal voltage 10.5VDC
1(ES) 3CU1210011 Double acting, 3 positions, with A and B 12VDC 4SOL512012 Nominal voltage 12VDC
closed in neutral position 24VDC 4SOL512024 Nominal voltage 24VDC
2(ES) 3CU1225010 Double acting, 3 positions, with A and B With Deutsch DT connector
open to tank in neutral position 4-- 10.5VDC 4SOL512111 Nominal voltage 10.5VDC
4-- 12VDC 4SOL512112 Nominal voltage 12VDC
I ”A” and “B” ports plugs *

G3/8 3XTAP722160 For single acting controls type 8ES1 and
8ES2
46 DAU003E
Complete controls
8ES solenoid control

Electric wiring example
8ES3 kit
double acting
1 0 2
1 1
2 2 8ES3 kit 8ES3 kit
double acting double acting
Connector 1 Connector 2
1 0 0 2
P⇒A P⇒B
B⇒T A⇒T
Operating condition diagram
-- + 400 (psi)
To battery (bar)
300 4500
Operating features
Pressure
CONTROL 200 3000
Internal leakage A(B)→T Operation area
(∆p = 100 bar -- 1450 psi / T = 40°C) : max. 15 cm3/min -- 0.91 in3/min 1500
100
COIL
0
Power rating . . . . . . . . . . . . . . . . . . . . : 36 W
0 15 30 45
Coil insulance . . . . . . . . . . . . . . . . . . . : class H
Flow (l/min)
Duty cycle . . . . . . . . . . . . . . . . . . . . . . : 100%
Wrench 22
24 Nm / 17.7 lbft
Allen wrench 4
6.6 Nm / 4.9 lbft
23.5
0.93 Emergency
manual override
Allen wrench 4
7 Nm / 5.2 lbft 6.6 Nm / 4.9 lbft 93.8
3.69
Spool
Coil with ISO4400 connector Coil with Deutsch DT connector

(needs connector C02: see page 129) (needs connector C19: see page 129)
DAU003E 47
Complete controls
Proportional hydraulic control type 8IM code 5IDR205021

It can be used with standard spools and body (body kit without seals on spool).
Coupling suggested with type 1CS spool (see page 13). 1 0 2
28
Allen wrench 5 1.10 VA VB
9.8 Nm / 17.7 lbft G 1/4
VA VB
Operating features
Max. pilot pressure . : 50 bar / 730 psi
Allen wrench 4
6.6 Nm / 4.9 lbft
47.5 42.5
1.87 1.67
193
7.60
Pilot pressure -- stroke diagram

Port B Port A
2 0 1
- 0.2 - 0.1 0.1 0.2 (in)
(bar) 20
(psi)
- 0.22
0.22
15
200
Pilot pressure
10
100
5
--5.5
Spool overlap area

5.5
0 Metering area
--6 --4 --2 0 2 4 6
Stroke (mm)
Connection example
Hydraulic pilot control valve

series SVM400 with curve type 026
VA1 VA2
A1 A2 Spool control curve
type 026 with step
T 0.1 0.2 (in)
30 (psi)
P
0.29
400
0.033
(bar)
Pilot pressure
B1 B2 20 300
203
14 200
10
VB1 VB2 6.5 100
94
0.85
7.25
0
0,0 2,0 4,0 6,0 7.6
Stroke (mm)
48 DAU003E
Outlet port options
It’s possible to have open centre, closed centre and carry--over.
Unloader valves are available: these valves need special bodies with appropriate cavity on lateral outlet port, the tank connection
T must be on top.
AET: open centre (standard)

See page 9.
AE: with carry-- over AEK: closed centre
Wrench 22 --42 Nm / 31 lbft
Allen wrench 8 --42 Nm / 31 lbft

G3/8
20.5 2.5
0.81 0.1
A1 B1 A2 B2 A1 B1 A2 B2
T T
P P
120 120
1750 1750
Description example: SD5/2--P(KG3--120)/18L/18L/AE Description example: SD5/2--P(KG3--120)/18L/18L/AEK
With hydraulic pilot unloader valve type L

For safety reasons it’s provided with pilot port plugged.
T
Pressure drop curve A2 B2
10 12
0.39 (psi)
(bar)
150
X
9
Pressure
X 100
6
G1/4
3 50
Wrench 24
42 Nm / 31 lbft 0
0 10 20 30 40 45
Flow (l/min)
Operating features Description example:
Internal leakage . . . . . . . . . . . . . . . . . : 10 cm3/min a 100 bar SD5/2--P(JG3--120)/18L/18L/AET--L
: 0.61 in3/min at 1450 psi
DAU003E 49
Outlet port options
With solenoid pilot unloader valve

With push and twist button for manual ovverride with detent.
Codes show at page 11 are referred to valves with ISO4400 coil, for complete valves with different electric connection contact
Sales Department.
Spare coils with several connectors are available, with and without diode.
123 Pressure drop

4.84
25 (psi)
Wrench 30 -- 42 Nm / 31 lbft (bar)
20 300
Pressure
15 200
10
100
5
Push and twist push--button
for manual override 0
0 20 40 60
Flow (l/min)
Oerating features
VALVE
Internal leakage (excited position) : max. 75 cm3/min at 100 bar . .
: max . 4.6 in3/min at 1450 psi
COIL
Depending on model: see following page
Normally open configuration type EL Normally closed configuration type ELC
A2 B2 A2 B2
T T
Description example: Description example:

SD5/2--P(JG3--120)/18L/18L/AET--EL--12VDC SD5/2--P(JG3--120)/18L/18L/AET--ELC--12VDC
50 DAU003E
Outlet port options
COIL CODES
CONNECTION TYPE
AMP JPT
ISO4400 Deutsch DT
Voltage senza diodo con diodo
12 VDC 2X4311012 2X4311015 2X4311212 2X4311412
24 VDC 2X4311024 - - 2X4311424
Coil with ISO4400 connector Coil with AMP JPT connector Coil with Deutsch DT connector
Connector side Connector side Connector side
Nominal voltage tolerance: ±10% Nominal voltage tolerance: ±10% Nominal voltage tolerance: ±10%
Power rating . . . . . . . . . . : 17 W Power rating . . . . . . . . . . : 17 W Power rating . . . . . . . . . . : 22 W
Nominal current . . . . . . . . : 1,58 A -- 12 VDC Nominal current . . . . . . . . : 1,3 A -- 12 VDC Nominal current . . . . . . . . : 1.76 A -- 12 VDC
: 0,81 A -- 24VDC : 0,74 A -- 24VDC : 0.9 A -- 24VDC
Coil insulation . . . . . . . . . : Classe F Coil insulation . . . . . . . . . : Classe F Coil insulation . . . . . . . . . : Classe H
Weather protection . . . . . : IP65 Weather protection . . . . . : IP65 Weather protection . . . . . : IP67
Duty cycle . . . . . . . . . . . . : 100% Duty cycle . . . . . . . . . . . . : 100% Duty cycle . . . . . . . . . . . . : 100%
NOTE: circuit with and without bidirectional NOTE: circuit with bidirectional diode
diode
LT: unloader valve prearrangement

T
A2 B2
Allen wrench 6
24 Nm / 17.7 lbft
SD5/2--P(JG3--120)/18L/18L/AET--LT
DAU003E 51
Srvice and auxiliary valves18.

All service and auxiliary valves need special body: contact Sales Department.
BP P
BPS
VS 3. 4.
Pilot check valves Anti- shock valve
1.
Mounting on the side

Relef valve of working ports
Mounting on the opposite

side of working ports
Relef valve Flow control valves
2. 7.
VSC(JG...)
Kit VD1 VD11

Kit VS
VSCT
VD12
Anti- shock + anticavitation valve

VD13
6.
VP
Anti- shock + anticavitation valve (fixed setting)
VU 5.
VM(...)
Kit V
VC
VP Kit VM
VT VMT
VM(...)
VU
VC
VMT
VT
52 DAU003E
1. Relief valves page 54 5. VM anti--schock+anti--cavitation valve page 59

TYPE CODE DESCRIPTION Flange mounted type with fixed setting and fitted with mounting block.
VS(G3-- 100) 3XCAR505113 Range 40 to 200 bar / 580 to 2900 psi TYPE CODE DESCRIPTION
standard setting 100 bar / 1450 psi VM(50) 5KIT326050 Setting 50 bar / 725 psi
VST 3XTAP419300 Valve blanking plug VM(60) 5KIT326060 Setting 60 bar / 870 psi
VM(70) 5KIT326070 Setting 70 bar / 1010 psi
2. Flange mounted relief valve page 55 VM(90) 5KIT326090 Setting 90 bar / 1300 psi
VSC(JG2-- 60) 5KIT105412 Range 40 to 80 bar / 580 to 1150 psi
standard setting 60 bar / 870 psi
VSCT XTAP623282 Valve blanking plug
Kit VS 5CO2420000 Mounting block kit
3. Pilot check valves page 56 VMT XTAP221340 Valve blanking plug
Supplied with mounting block Kit VM 5CO2820020 Mounting block kit
Directv type
BP1 602002000* Block with valve on port A 6. V anti--schock+anti--cavitation valve pag. 61
BP2 602002000* Block with valve on port B Set of valves fitted with mounting block.
BP3 602002100* Block with valves on ports A and B TYPE CODE DESCRIPTION
BP XCAR605110 Single valve Kit V 5CO2820010 Mounting block kit
With pre--opening T XTAP524280 Valve blanking plug
BPS1 602003000* Block with valve on port A C 5KIT406110 Anti--cavitation valve
BPS2 602003000* Block with valve on port B Anti--shock valves
P(G2) 5KIT206112 Range 60 to 125 bar / 870 to 1800 psi
BPS3 602003100* Block with valves on ports A and B
BPS XCAR605210 Single valve P(G3) 5KIT206113 Range 80 to 200 bar / 1150 to 2900 psi
BPT XTAP627300 BP and BPS valves blanking plug P(G4) 5KIT206114 Range 160 to 250 bar / 2300 to 3600 psi
Anti--shock + anti--cavitation valves
4. P antishock valves page 57 U(G2) 5KIT305112 Range 40 to 100 bar / 580 to 1450 psi
Cross return type, supplied with mounting block standard setting 80 bar / 1150 psi
TYPE CODE DESCRIPTION U(G3) 5KIT305113 Range 80 to 200 bar / 1150 to 2900 psi
P1(D3-- 100) 602001000* Block with valve on port A standard setting 120 bar / 1750 psi
U(G4) 5KIT305114 Range 160 to 315 bar / 2300 to 4600 psi
P2(D3-- 100) 602001000* Block with valve on port B
P3(D3-- 100) 602001100* Block with valves on ports A and B
P(D2-- 60) 5CAR211112 Single valve: range 40 to 100 bar / 580 to
1450 psi,standard setting 60 bar / 870 psi
P(D3-- 100) 5CAR211113 Single valve: range 80 to 200 bar / 1150
7. Flow control valves page 65
to 2900 psi, standard setting 100 bar / Flow control on every section; with auxiliary inlet
1450 psi TYPE CODE DESCRIPTION
P(D4-- 200) 5CAR211113 Single valve: range 180 to 315 bar / 2600 VD11 2S0PP10002000 Fine regulation from 3 to 30 l/min
to 4600 psi, standard setting 200 bar / VD12 2S1636020211 As VD11, one turn with detent
2900 psi VD13 2S0PP10002002 12VDC proportional solenoid valve
PT XTAP526430 Valve blanking plug (for configuration P1, Kit VD1 5CO2822010* Mounting block kit
P2)
NOTE -- Valve setting at points 1--2--4--5--6 are referred to 10 l/min flow.

NOTE -- (*) Codes are referred to BSP threads.
DAU003E 53
VS relief valve
It’s suggested for flow up to 25 l/min, and it’s mounted on parallel body to limitate the pressure, at lower value than main relief valve
(min. gap 20 bar / 290 psi ), on downstream section.
It’s in parallel with flow trough and it works only with single operation.
VS ( G 3 -- 100 )
Pressure setting in bar (standard 100 bar / 1450 psi)

Spring type

Adjustment type
T
P C Allen wrench 3
max.
Wrench 10
B1 B2 9.8 Nm / 7.2 lbft
24.5
0.96
0.55
14
Wrench 17
24 Nm / 17.7 lbft
C
Wrench 19
24 Nm / 17.7 lbft
C -- C C -- C
18.5 18.5
0.73 0.73
Performance data
Hydraulic circuit Spring nr. 3 (blue band)
A1 B1 A2 B2
400
(bar) (psi)
T 300 4500
Pressure
200 3000
P
100 1500
100 0
120 1450
1750 0 10 20 30
Flow (l/min)
Time response
SD5/2--P(KG3--120)/18L/VS(G3--100)/18L/AET--PSA
(% ∆P)
105%
VST: valve blanking plug
95%
Pressure
1450 psi
Allen wrench 6 90%

100 bar
42 Nm / 31 lbft
10%
0.16
4
0,08” Time (”)

TIME RESPONSE
54 DAU003E
VSC relief valve

It’s flange mounted on parallel body on the opposite side of working ports, the function to limit the pressure, at lower value than main
relief valve (min. gap 20 bar / 290 psi) on downstream sections.
It’s in parallel with flow through line and it works only with single operation.
It needs a dedicated body with extra machining: for production requirements, the block (2) is flanged (1) before the final honing of
spool hole, while the valve (3) is mounted during final assembling phase.
For information contact Sales Department.
A1 B1 A2 B2
1
T
3 2
120
1750
VSC ( J G 3 -- 100 )
Standard setting in bar
(for value see page 53)
100
Adjustable spring type (2, 3, 4). 1450
Adjustment type (G, H). Description example:

SD5/2--P(JG3--120)/18L/VSC(JG3--100)/18L/AET
37.5 43
1.48 1.69 32 24.5
21.5 1.26 0.96
0.85
13
0.51
A1 A2
1.34
34
T
max. 4.17
max. 106
B1 B2
54.5
2.15
Wrench 4
6.6 Nm / 4.9 lbft
NOTE -- For performance data, wrench

and tightening force, please see page 12.
53 37
2.09 1.46
DAU003E 55
BP, BPS pilot check valves

Cast iron block with pilot check valves.
BP1 BP2 BP3
BPS 1 BPS1 BPS2 BPS3
A B A B A B
1 mounted on port A.
2 mounted on port B.
3 mounted on ports A and B.
BP direct type
BPS with pre--opening
BP1 configuration BP3 configuration

Example of pressure on port A and port B to tank Example of pressure on port A and port B to tank
A B A B
Wrench 27
42 Nm / 31 lbft
Wrench 27
42 Nm / 31 lbft
Wrench 19
42 Nm / 31 lbft
P T P T
Example of pressure on port B and port A to tank Example of pressure on port B and port A to tank
A B A B
T P T P
Performance data
BP valve pressure drop BPS valve pressure drop
40 40
(bar) (psi) Pilot ratio (bar) (psi)
450 Type With 450
30 Main 30
pre--opening
Pressure
Pressure
20 300 20 300
BP / 1 : 5.3
10 150 10 150
BPS 1 : 16 1 : 3.2
0 0
0 20 40 60 0 20 40 60
Flow (l/min) Flow (l/min)
56 DAU003E
P anti--shock valves with cross return

Cast iron block with antishock valves.
P1 P2 P3
P 1 ( D 3 - 100 ) A B A B A B
100
Standard setting in bar 1450
100
Spring type (2,
3, 4). 1450 100
1450
Adjustment with blind nut (D).
1 mounted on port A. 100
1450
2 rmounted on port B.
P1 configuration P3 configuration
Example of pressure on port A and port B to tank Example of pressure on port B and port A to tank
A B A B
Allen wrench 8
Wrench 27
42 Nm / 31 lbft
42 Nm / 31 lbft
Allen wrench 5
Wrench 21
24 Nm / 17.7 lbft
P T T P
Performance data
Spring nr. 2 (green band) Spring nr. 3 (blue band)
400 400
(bar) (psi) (bar) (psi)
300 4500 300 4500
Pressure
Pressure
200 3000 200 3000
100 1500 100 1500
0 0
0 20 40 60 0 20 40 60
Spring nr. 4 (red band)

Time response
400 (% ∆P)
(bar) (psi)
4500 105%
300
Pressure
95%
Pressure
200 3000
1750 psi
90%
120 bar
100 1500
10%
0
0 20 40 60 Time (”)
Flow (l/min) 0,12”
TIME RESPONSE
DAU003E 57
Mounting example for valves type P and BP, BPS

58
36 2.28
1.42 30 56.5
P3 configuration BP3 configuration 1.18 2.22
valve block valve block 19 21.5
0.75 0.85
0.55
14
16.5
0.65
0.75
19
4.79 =
= 3.82 =
3.66 =
121.6
3.46
1.97
2.36
5.04
97
128
60
88
93
50
=
1.02
26
0.83
21
0.79
14.3
0.56
P3 configuration 20 BP3, BPS3 configuration
23 30 37 27 5.5
0.91 1.18 1.46 1.06 0.22
L1 special lever box
Standard lever box
code: 5LEV105050
Example of extra machining on directional valve body
28 9 28 18.5 62.5
1.10 0.35 1.10 0.73 2.46
Milled surface with

fixing threaded holes
1.6
16.5
0.65
1.06
27
M5
37.5
1.48
10
0.39
13
0.51
58 DAU003E
VM anti--shock and anti--cavitation

They are flange mounted on the opposite side of working ports, connected in parallel with A and B ports and with outlet on T port.
It needs a dedicated body with extra machining: for production requirements, the block (2) is flanged on body (1) before the final
honing of spool hole, while the valve (3) is mounted during final assembling phase.
Valve on port B
Valve on port A
3 2
21.9 36.6
0.86 1.44 40.5 24.5
15.3
1.59 0.96
0.60
27.5
1.08
0.55
14
A1 A2
T
3.39
86
P
0.22
5.5
B1 B2
13.5
0.53
53 37
2.09 1.46
DAU003E 59
VM 1 (100) VM1 VM2 VM3
Valve setting in bar A B A B A B

1 mounted on port A T T T
2 mounted on port B
3 mounted on ports A and B
100 100
1450 1450
100 100
1450 1450
Pressure--flow diagram
Example of VM1 configuration
350 (psi)
(bar)
300 4500
250
200 3000
Pressure
150
100 1500
50
Allen wrench 6
24 Nm / 17.7 lbft 0
0 10 20 30 40 45
Flow (l/min)

24 Nm / 17.7 lbft 6.6 Nm / 4.9 lbft
60 DAU003E
V anti-- shock and anti-- cavitation

They are anti--shock (VP), anti--shock and anti--cavitation (VU) and anti--cavitation (VC) service valves, flange mounted on the
opposite side of working ports connected in parallel with A and B ports.
They need a dedicated body with extra machining: for production requirements, the blocks (2) are flanged on body (1) before the
final honing of spool hole, while the valves (3) are mounted during final assembling phase.
Valve on port A Valve on port B
3 2 2 3
22.5 36
0.89 1.42
18 1 35 25
0.71 0.04 1.38 0.98
16
0.63
D
57.5
2.26
A1 A2
32.5
1.28
T
2
0.08
P
P
B1 B2
Dimension D value (mm / in)

VP VU VC VT
14 / 0.55 14 / 0.55
9.5 / 0.37 5.5 / 0.22
max. max.
53 37
2.09 1.46
DAU003E 61
V anti-- schock+anti-- cavitation valves

Anti-- shock valve
VP1 VP2 VP3
VP 1 ( G 3 -- 100 ) T A B T T A B T

Spring type (2, 3, 4). 100 100 100 100
1450 1450 1450 1450
Adjustment type (G, H).
Adjustment type
Notch
1.5 mm / 0.06 in
Wrench 22
42 Nm / 31 lbft
Allen wrench 5
9.8 Nm / 7.2 lbft
Performance data
400 (psi) 400 (psi)

(bar) (bar)
300 4500 300 4500
Pressure
Pressure
200 3000 200 3000
100 1500 100 1500
0 0
0 20 40 60 0 20 40 60
Spring nr.4 (red band)

Time response
400 (psi) (% ∆P)
(bar)
105%
300 4500
Pressure
95%
Pressure
200 3000 90%

1450 psi
100 bar
100 1500
10%
0
0 20 40 60 Time (”)
0,02”
Flow (l/min) TIME RESPONSE
62 DAU003E

Anti-- shock + anti-- cavitation valve
VU1 VU2 VU3
VU 1 ( G 3 - 100 ) T A B T T A B T

Spring type (2,3, 4). 100 100 100 100
1450 1450 1450 1450
Adjustment type
Notch
1.5 mm / 0.06 in
Wrench 22
42 Nm / 31 lbft
Allen wrench 5
9.8 Nm / 7.2 lbft
Performance data
400 (psi) 400 (psi) 400 (psi)

(bar) (bar) (bar)
300 4500 300 4500 300 4500
Pressure
Pressure
Pressure
200 3000 200 3000 200 3000
100 1500 100 1500 100 1500
0 0 0
0 20 40 60 0 20 40 60 0 20 40 60
Pressure drops Time response
150 (psi)
(% ∆P)
(bar) 2000
120 105%
1500
Pressure
90 95%
Pressure
90%
1750 psi
1000
120 bar
19.5 bar / 280 psi

60
OPENING PEAK
30 500
10%
0
0 20 40 60 0.1” 0.15” Time (”)
Flow (l/min) TIME REPONSE TRANSITORY
DAU003E 63

Anti-- cavitation valve
VC1 VC2 VC3
VC 1 T A B T T A B T
Pressure drop
120 (psi)
(bar) 1500
90
Pressure
1000
60
30 500
0
Wrench 24 0 20 40 60
42 Nm / 31 lbft Flow (l/min)
Allen wrench 5
9.8 Nm / 7.2 lbft
Valve blanking plug VT1 VT2 VT3

T A B T T A B T
VT 1
Allen wrench 8
24 Nm / 17.7 lbft
Allen wrench 5
9.8 Nm / 7.2 lbft
64 DAU003E
VD1 flow control valves

Block with pressure compensated 3--way flow control valve, to be flange mounted on body with parallel circuit.
The cavity is oriented toward lever side.
The flow is regulated on every working section while the exceeding flow goes to tank: max. regulated flow 30 l/min (with inlet on P1
port).
T
3
P1
2
20 62
24.5 35 0.79 2.44
0.96 1.38
13
0.51
11.5
0.45
A1 A2
P1
22.3
0.88
T
T
P
3.03
77
B1 B2
D
17.5 59
0.69 23
2.32 0.91
VD11 VD12 VD13
121 / 4.76 171.5 / 6.75 171.5 / 6.75
DAU003E 65

Manual control
VD11: continuous fine regulation
Hydraulic circuit
Allen wrench 4 Wrench 27
6.6 Nm / 4.9 lbft 24 Nm / 17.7 lbft A1 B1
Description example: SD5/2--P(JG3--120)VD11/18L/18L/AET
120
VD12: one turn with detent handknob regulated 1750
P1
C
R

6.6 Nm / 4.9 lbft 24 Nm / 17.7 lbft
66 DAU003E

VD13 with proportional solenoid control
Hydraulic circuit
A1 B1
ISO4400 connection P
(needs C02 connector,
see page. 129)
120
1750
P1
C
R
6.6 Nm / 4.9 lbft 24 Nm / 17.7 lbft
Proprtional solenoid flow control valve connection

It’s shows a configuration with push--button panel type UPA.
Emergency Potentiometer for

push--button valve adjustment
Solenoid operating feautures
Nominal voltage . . . . . . . . . : 12 VDC
Power rating . . . . . . . . . . . . : 28 W
Duty cycle . . . . . . . . . . . . . . : 100%
STOP
ISO4400
connector
To battery
Push--button panel type:
UPA12/100/SC01B22
Performance data
Pressure--flow diagram Flow regulation diagram
Qin = 45 l/min Qin = 45 l/min -- P = 100 bar (1450 psi)
1000 2000 3000 (psi) 0 0.3 0.6 0.9 1.2 Current (A)
40 (l/min) 40
(l/min)
30 30
Priority flow
Priority flow
F J F VD11 flow control valve

20 20 Y VD12 flow control valve
Y
J VD13 flow control valve
10 10
0 0
30 90 150 210 270 0.0 0.5 1.0 1.5 2.0 2.5 (n.of turn)
Pressure (bar)
0 3 6 9 12 15 18 (n.of clicks)
DAU003E 67
68 DAU003E
Other executions
SD5/1- N . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . page 70
It’s available only with one working section and it can be used in hydraulic cir-
cuits where carry--over doesn’t required.
H For controls, spool positioning and valves, refer to directional valve with paral-
lel circuit.
SD5/1- D . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . page 71
cuits where carry--over is required.
H For controls and spool positioning refer to directional valve with parallel circuit.
H Configurations with service and auxiliary valves aren’t available
SD5- S: with series circuit . . . . . . . . . . . . . . . . . . . . . . . . . . . . page 72

Available from 2 to 6 sections, it can be used in systems wich one downstream
section from series connection must work with upstream ones at the same time.
H On the same body are possible more than one connection.
H It’s not available the carry--over circuit.
lel circuit.
SD5- SP: with tandem circuit . . . . . . . . . . . . . . . . . . . . . . . . . page 74

Available from 2 to 6 sections, for security reasons it can be used in systems
which is required to prohibit engagement of downstream sections from tandem
connection when the upstream sections are working.
lel circuit.
DAU003E 69
SD5/1--N directional valve with left inlet
Dimensional data
105.5 63.5 5
4.15 2.50 0.20
14 73 45
0.55 2.87 1.77
0.33
8.5
1.34
34
3.19
103
4.06
81
7.32
186
2.01
51
spool out
45.5
1.79
1
24°
0.45
0.79
11.5
20
15°
0
1.81
46
15°
24°
M8
2
24.5 30 27 24.5
0.96 1.18 1.06 0.96 3
90 spool in
3.54
Hydraulic circuit Performance data

Pressure drop curve
A1 B1
15 (psi)
(bar) 200
10 150
P P→A(B)
T
Pressure
100
P→T
5
50
120
1750 A(B)→T
0
0 15 30 45 60
Description example: Flow (l/min)
SD5/1--N(JG3--120)/18L
Code: 102110033
70 DAU003E
directional valve with left inlet SD5/1--D
Dimensional data
102 63.5 5
4.02 2.50 0.20
13 73 45
0.51 2.87 1.77
0.33
8.5
1.34
34
4.06
3.19
103
81
7.32
186
2.01
51
spool out
45.5
1.79
1
24°
0.79
0.45
11.5
20
15°
0
1.81
46
15°
24°
M8
2
23.5 30 27 24.5
0.93 1.18 1.06 0.96 3
90 spool in
3.54
A1 B1 Pressure drop curve
20 (psi)
(bar) 200
T
15
150
P P→A(B)
C 10
Presure
100
P→C
5 50
120
1750 A(B)→T
0
0 15 30 45 60
SD5/1--D(JG3--120)/18L
Code: 102160027
DAU003E 71
SD5--S directional valve with left inlet
Dimensional data
63.5 5
2.50 0.20
45
E 1.77
F 24.5
12.5
0.96
0.49
0.33
8.5
1.34
34
4.06
3.19
103
7.32
81
186
2.01
51
spool out
45.5
1.79
3
0.45
11.5
1
24°
0.79
20
15°
0
1.77
45
M8 15°
24°
2
23 30 37 27 90
0.91 1.18 1.46 1.06 3.54
3
spool in
TYPE TYPE
SD5/2--S 137.5 5.41 110 4.33 5.2 11.4 SD5/5--S 248.5 9.78 221 8.70 10.1 22.3
SD5/3--S 174.5 6.87 147 5.79 6.9 15.2 SD5/6--S 285.5 11.2 258 10.2 11.7 25.8
SD5/4--S 211.5 8.33 184 7.24 8.1 17.9
72 DAU003E
directional valve with left inlet SD5--S
Hydraulic circuit
The description of SD5 valve with series circuit is marked with letter “S” and one figure wich indicate the downstream sections from
series connection.
A1 B1 A2 B2 A3 B3 A4 B4
Available body kits *
CODE DESCRIPTION
5KC1153040 SD5/2--S1
5KC1253003 SD5/3--S1
P 5KC12D3000 SD5/3--S1+1
T
5KC1283003 SD5/4--S1
5KC12E3000 SD5/4--S1+1+1
5KC1324033 SD5/5--S1
5KC1073001 SD5/5--S1+1+1+1
120 5KC13A3000 SD5/5--S2+1
1750
5KC1363003 SD5/6--S1
Include boby, seals and load check
Description example: SD5/4--S1(JG3--120)/18L/18L/18L/18L valves.
Code: 1024B0027 *
NOTE (*) -- Codes are referred to BSP thread.
Performance data
Pressure drop P→T Pressure drop P→A(B)
on 6 sections directional valve
40 40
P→A6(B6)
30 6 sections 450 30 450
4 sectionis
Pressure
Pressure
20 300 20 300
2 sections P→A1(B1)
10 150 10 150
0 0
0 15 30 45 60 0 15 30 45 60
Pressure drop
Pressure drop A(B)→T between port A(B) before series
on 6 sections directional valve connection and port A(B) after
40 40
(bar) (psi) (psi)
A1(B1)→T (bar)
30 450 30 450
Pressure
300 300
Pressure
20 20
A6(B6)→T
10 150 10 150
0 0
0 15 30 45 60 0 15 30 45 60
DAU003E 73
SD5--SP directional valve with left inlet
Dimensional data
63.5 5
Carry--over 2.50 0.20
20.5 45
E 1.77
0.81
24.5
12,5 F 0.96
0.49
0.33
8.5
1.34
34
103
3.19
4.06
7.32
81
186
2.01
51
spool out
45.5
1.79
3
0.45
11.5
1
24°
0.79
20
15°
0
1.77
45
M8 15°
24°
2
23 30 37 27 90
0.91 1.18 1.46 1.06 3.54 3
spool in
TYPE TYPE
SD5/2--SP1 137.5 5.41 110 4.33 4.8 10.6 SD5/5--SP4 248.5 9.78 221 8.70 10.2 22.5
SD5/3--SP2 174.5 6.87 147 5.79 6.7 14.8 SD5/6--SP5 285.5 11.2 258 10.2 11.3 24.9
SD5/4--SP3 211.5 8.33 184 7.24 8.1 17.6 SD5/7--SP6 322.5 13.1 295 11.6 12.7 28
74 DAU003E
directional valve with left inlet SD5--SP
Hydraulic circuit
The description of SD5 valve with tandem circuit is marked with letters “SP” and one figure wich indicate the downstream sections
from tandem connection.

CODE DESCRIPTION
A1 B1 A2 B2 A3 B3 A4 B4 5KC1183000 SD5/2--SP1
5KC12G3000 SD5/3--SP2
5KC1303000 SD5/4--SP1
T
5KC12H3000 SD5/4--SP1+1
5KC12I3000 SD5/4--SP2+1
P 5KC1293000 SD5/4--SP3
5KC13D3000 SD5/5--SP2+2
5KC1343000 SD5/5--SP3+1
5KC1333000 SD5/5--SP4
5KC1393000 SD5/6--SP3+1
120 5KC13Y3000 SD5/6--SP3+2
5KC1373000 SD5/6--SP5
5KC13I3000 SD5/7--SP3+1
Description example: SD5/4--SP3(JG3--120)/18L/18L/18L/18L/AET 5KC13G3000 SD5/7--SP4
5KC13L3000 SD5/7--SP5+1
Code: 1024A0016 *
5KC13F3000 SD5/7--SP6
valve.
Performance data
40 40
30 6 sections 450 30 450

P→A6(B6)
4 sections
Pressure
Pressure
20 300 20 300
10 150 10 150
0 0
0 15 30 45 60 0 15 30 45 60
Pressure drop A(B)→T

40
(bar) (psi)
A1(B1)→T
30 450
Pressure
20 300
A6(B6)→T
10 150
0
0 15 30 45 60
Flow (l/min)
DAU003E 75
SD5
76 DAU003E
SD5
Contents
Directional valve with parallel circuit

Dimensional data . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 78
Hydraulic circuit . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 79
Ordering codes . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 80
Inlet relief options . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 12
Spools . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 82
“A” side spool positioners . . . . . . . . . . . . . . . . . . . . . . . . . . 86
“B” side options . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 39
Complete controls . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 44
Outlet port options . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 97
ordering codes . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 100
port relief valves . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 102
flange mounted relief valves . . . . . . . . . . . . . . . . . . . . 103
fixed setting antishock and anticavitation valves . . . . 104
adjustable setting antishock and anticavitation valves 106
flow control valves . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 110
Other executions
Main features . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 113
Directional valve SD5/1--N . . . . . . . . . . . . . . . . . . . . . . . . . 114
Directional valve SD5/1--D . . . . . . . . . . . . . . . . . . . . . . . . . 115
Directional valve SD5--S with series circuit . . . . . . . . . . . 116
Directional valve SD5--SP with tandem circuit . . . . . . . . . 118
Directional valve SDM105 eith flow control . . . . . . . . . . . 120
DAU003E 77
SD5 directional valve with right inlet
Dimensional data (parallel circuit)
WALVOIL Type
MADE IN ITALY
102219002
WALVOIL
P0200001
SD5/2--P
SD5/2--P
Production batch:
P0500001 P05 = production year (2005)
102200039 00001 = progressive number
MADE IN ITALY
Code
Carry--over
20.5 63.5 5
0.81 2.5 0.20
27 37 30 23 45
1.06 1.46 1.18 0.91 1.77
0.45
11.5
0.33
8.5
45.5
1.79
2.01
51
198.5 max.
4.06
7.81 max.
103
3.19
81
1.34
34
spool out
3
0.41 0.45
10.5 11.5
1
24°
0.79
20
15°
0
1.73
44
15°
M8 24°
2
F 12.5 24.5
0.49 0.96 3
E 90
3.54 spool in
TYPE TYPE
SD5/1--P 100.5 3.96 73 2.87 3.5 7.7 SD5/5--P 248.5 9.78 221 8.70 10.1 22.3
SD5/2--P 137.5 5.41 110 4.33 5.2 11.5 SD5/6--P 285.5 11.24 258 10.16 11.7 25.8
SD5/3--P 174.5 6.87 147 5.79 6.9 15.2 SD5/7--P 322.5 12.70 295 11.61 13.2 29.1
SD5/4--P 211.5 8.33 184 7.24 8.1 17.9
78 DAU003E
directional valve with right inlet SD5
Hydraulic circuit
Parallel
Standard configuration with side inlet and outlet and open centre (AET execution).
Positioner kit Main relief valve
Plug for open centre

Allen wrench 8
24 Nm / 17.7 lbft Flow through
(LC)
A P
B Tank line Pressure line
Port B line Check valve

Allen wrench 4
Port A line 24 Nm / 17.7 lbft
Lever pivot box
Standard configuration Configuration with upper inlet and outlet

T
B2 A2 B1 A1 B2 A2 B1 A1
P
T
120 120
1750 1750

SD5/2--P(JG3--120)/ED--18L/ED--18L/AET SD5/2--P(JG3--120)/ED--18L/ED--18L/AET--PSA
DAU003E 79
Ordering codes3.
Description example: Valve setting (bar)

Valve setting (bar) 1st section following section
SD5 / 2 -- P (JG3-- 120) / ED - 1 8 L / ED - 18ES3 . P3(G3-- 100) / AET *
1. 2. 3. 4. 5. 6. 7. 8.
2.
9.
I
6.
7.
4.
6.
8.
1.
3.
1. Body kit * 3. Spool options page 82

TYPE CODE DESCRIPTION TIPO CODICE DESCRIZIONE
1-- P 5KC1193000 Parallel, 1 section ED-- 1 3CU1210730 Double acting, 3 positions, with A and B
2-- P 5KC1223000 Parallel, 2 sections closed in neutral position
3-- P 5KC1243000 Parallel, 3 sections ED-- 1B 3CU1222700 Double acting, 3 positions, with B open to
5-- P 5KC1313000 Parallel, 5 sections ED-- 2 3CU1225730 Double acting, 3 positions, with A and B
6-- P 5KC1353000 Parallel, 6 sections open to tank in neutral position
7-- P 5KC13E3000 Parallel, 7 sections ED-- 2H 3CU1225790 Double acting, 3 positions, with A e B
Include boby, seals and load check valve. partially open to tank in neutral position
ED-- 4 3CU1235700 Single acting on B, 3 positions, A plugged
requires G3/8 plug (see part I )
2. Inlet relief options page 12 Special spools for particular positioner kits . . . . . . . . . . . . . . . page 84
ED-- 5PY 3CU1245700 Double acting, 4 positions, floating circuit
TYPE CODE DESCRIPTION in 4th position with spool out, with check
VMD5 direct pressure relief valve type J valve
Standard setting is referred to 10 l/min flow. Special spools for standard positioner kits . . . . . . . . . . . . . . . . page 85
(JG2-- 63) 5KIT105412 Range 40 to 63 bar / 580 to 900 psi ED-- 8F 3CU1261700 Double acting, 3 positions, regenerative
standard setting 63 bar / 900 psi circuit in 2nd position with spool out
(JG3-- 120) 5KIT105413 Range 50 to 200 bar / 725 to 2900 psi
SV XTAP623282 Relief valve blanking plug
80 DAU003E
Ordering codes
4. “A” side spool positioners page 86 5. “B” side options page 39

8 5V08104000 With spring return in neutral position L 5LEV105000 Standard lever box
8D 5V08104200 With spring return in neutral position and LM10 5LEV205000 Lever box for M10 handlever
pin with M6 female thread for dual control LF1 5LEV105102 Lever box with adjustable flow limiter
8D2 5V08104220 With spring return in neutral position and LEB 5LEV605000 Safety lever box, vertical configuration
pin with M8 male thread for dual control LUP 5LEV805005 Safety lever box, horizontal configuration
8F2 5V08104101 With spring return in neutral position and SLP 5COP105000 Witout lever box, with dust--proof plate
adjustable flow limiter SLC 5COP205000 Witout lever box, with endcap
19 5V19104000 2 positions, with spring return in neutral TQ 5TEL105110 Flexible cable connection
position from position 1 LCB 5CLO205100 Joystick lever for 2 sections operation
20 5V19104000 2 positions, with spring return in neutral
9 5V09104010 With detent in position 1 and spring return
6. Complete controls page 44
in neutral position Proportional hydraulic control type 8IM and ON/OFF solenoid control
10 5V10104011 With detent in position 2 and spring return type 8ES.
in neutral position
11 5V11104000 Detent in positions neutral, 1 and 2
12 5V12104000 Detent in positions 1 and 2
7. Aux. and service valves page 100
15 5V15104000 2 positions, detent in positions 1 and Port relief, anti--shock, pilot operated check and flow regulation valves.
neutral
16 5V16104000 2 positions, detent in positions 2 and
neutral
8. Outlet port options page 97
9BZ 5V09204010 With detent in position 1 and spring return TYPE CODE DESCRIPTION
in neutral position AET XTAP623170 Open centre plug
10BZ 5V10204010 With detent in position 2 and spring return AEK 3XTAP522282 Closed centre plug
in neutral position AE 3XGIU522460* G3/8 carry--over sleeve
11BZ 5V11204010 Detent in positions 1 and 2 and spring AET-- L XCAR405300 With hydraulic pilot unloader valve
return in neutral position AET-- EL YCAR405305 With 12VDC electric control unloader
8MG3 5V08104660 With spring return in neutral position and valve; normally open circuit
microswitch in positions 1 and 2 YCAR405310 As previous 24VDC
8P 5V08104701 ON/OFF pneumatic kit AET-- ELC 5CAR405330 With 12VDC electric control unloader
8EP3 5V08104735 ON/OFF 12 VDC electro--pneumatic kit valve; normally closed circuit
5V08104740 ON/OFF 24 VDC electro--pneumatic kit 5CAR405331 As previous 24VDC
8ED3 5V08104350 ON/OFF 12 VDC electro--hydraulic kit AET-- LT XTAP523370 Prearranged for unloader valve, with
5V08104351 ON/OFF 24 VDC electro--hydraulic kit blanking plug
Particular positioner kits for special spools . . . . . . . . . . . . . . . page 96
13QN 5V13404020 4 pos. with spring return in neutral pos.
and detent in 4th pos.: for spool 5PY 9. Inlet and outlet selection * page 79
PSL 3XTAP722160 Side ports; need n.2 G 3/8 plugs, standard
II Optional handlevers configuration (omit in valve description)
TYPE CODE DESCRIPTION PSA 3XTAP722160 Upper ports; need n.2 G 3/8 plugs
AL01/M8x120 170011012 For lever L: height 120 mm / 4.72 in
AL01/M10x150 170012015 For lever LM10:
height 150 mm / 5.91 in I ”A” and “B” ports plugs *
AL08/M12x150 170013115 For joystick LCB: TYPE CODE DESCRIPTION
height 150 mm / 5.91 in G3/8 3XTAP722160 for single acting spool type 3
DAU003E 81
Spool options
Tipo ED--1
For special requirement, spool 1CEX code 3CU1210780 suggested for flow up to 15 l/min
1 0 2
A B
A B
"
stroke:
LC T P T + 5.5 mm / 0.22 in P T
P→A B→T
29
13.5 0.35
20
1 0 2
0.53 A B
0.79 A B
LC T P T P T
145.5
5.73
1 0 2
A B
A B
A
stroke:
LC T P T -- 5.5 mm / 0.22 in P T
P→B A→T
Performance data
Spool metering P→A(B) Spool metering A(B)→T

0.1 0.2 (in) 0.1 0.2 (in)
60 60
(l/min ) (l/min )
40 40
Flow
Flow
J F
F Y
J
20 20
Qin = 45 l/min
Y F P(on ports) = 63bar / 900 psi
0 0
82 DAU003E
Spool options
Type ED--1B
1 0 2
A B + 5,5 mm / 0.22 in
A B
(1) "
(0)
A (2)
LC T P T P T
-- 5,5 mm / 0.22 in
P--A closed, B→T, flow through line (LC) open
Type ED--2
1 0 2
A B + 5,5 mm / 0.22 in
A B
(1) "
(0)
A (2)
LC T P T P T
-- 5,5 mm / 0.22 in
Type ED--2H
1 0 2
A B + 5,5 mm / 0.22 in
A B
(1) "
(0)
A (2)
LC T P T P T
-- 5,5 mm / 0.22 in
P closed, A--B partially open to tank,
Type ED--4
Port A closed
Allen wrench 6
24 Nm / 17.7 lbft B
1 0 2
+ 5,5 mm / 0.22 in
B
(1) "
(0)
A (2)
LC T P T P T
-- 5,5 mm / 0.22 in
P--A--T closed, flow through line (LC) open
DAU003E 83
Spool options
Tipo ED--5PY
This spool must be coupled with positioner type 13QN (see page 96).
3 1 0 2
A B
A B
""
stroke:
LC T P T + 9 mm / 0.35in P T
A--B→T (floating detent)
corsa + 9 mm 3 1 0 2
A B
A B
"
stroke:
LC T P T + 4.5 mm / 0.18 in P T
P→A , B→T
3 1 0 2
A B
A B
LC T P T P T
P--A--B--T closed,
with flow through line (LC) open
3 1 0 2
A B
A B
A
stroke:
LC T P T + 4.5 mm / 0.18 in P T
P→B , A→T
Performance data
0.1 0.2 (in)
60 20 (psi)
(l/min ) (bar)
15
40 B→T 200
Pressure
Flow
A→T P→A 10
A(B)→T
20 100
P→B 5
0 0
0.0 1.0 2.0 3.0 4.0 5.0 5.5 0 15 30 45 60
84 DAU003E
Spool options
Type ED--8F
1 0 2
A B
A B
"
stroke:
LC T P T + 5.5 mm / 0.22 in P T
1 0 2
A B
A B
LC T P T P T
1 0 2
A B
A B
A
stroke:
LC T P T -- 5.5 mm / 0.22 in P T
P→ B , A → T
Performance data
Qin = 45 l/min / P(on ports) = 100 bar -- 1450 psi (in first section)
0.1 0.2 (in)
60 20 (psi)
(l/min ) (bar)
15
40 200
Pressure
Flow
B→A
10
P→A
20 100
A→T P→B 5
0 0
0.0 1.0 2.0 3.0 4.0 5.0 5.5 0 15 30 45 60
DAU003E 85

8 kit
It’s supplied with standard spring type D (see force--stroke diagram) and available with lighter spring type C (8MC code: 5V08204000)
or heavier type E (8ME code: 5V08404000).
- 0.2 - 0.1 0 0.1 0.2 (in)
1 0 2 300 (lbf)
(N) E 60
Allen wrench 4 200
D 40
6.6 Nm / 4.9 lbft
100 C 20
Allen rench 5 Force
0 0
9.8 Nm / 7.2 lbft
--100 C - 20
--200 D - 40
E - 60
--300
--6 --5 --4 --3 --2 --1 0 1 2 3 4 5 6
40 Stroke (mm)
1.57
8D kit
Spool end joint code XPER315400, is available on request in order to screw onto pin.
Allen wrench 4
1 0 2
Spool end joint dimensions
6.6 Nm / 4.9 lbft
Wrench 9
9.8 Nm / 7.2 lbft
M6
12
15
4
0.59
0.47
0.16 10 20
0.39 0.79
8
0.31
M6
40
18
8
0.31
1.57
0.71
47.5 40
1.87 1.57
8D2 kit
1 0 2
Allen wrench 4
6.6 Nm / 4.9 lbft
Wrench 9
9.8 Nm / 7.2 lbft
M8
40 40
1.57 1.57
87.5
3.44
86 DAU003E

8F2 kit
Allen wrench 5 Allen wrench 4 1 0 2

9.8 Nm / 7.2 lbft 6.6 Nm / 4.9 lbft
Wrench 13
24 Nm / 17.7 lbft
Allen wrench 4
M8x1
40
1.57
55
2.17
19 kit
0.1 0.2 (in)
300 (lbf)
Allen wrench 4 (N) 60
6.6 Nm / 4.9 lbft 200 40
100 20
Force
Allen wrench 5
0 0
9.8 Nm / 7.2 lbft
--100 - 20
--200 - 40
- 60
--300
40 0 1 2 3 4 5 6
1.57 Stroke (mm)
20 kit
- 0.2 - 0.1 (in)
300 (lbf)
(N) 60
Allen wrench 4
6.6 Nm / 4.9 lbft 200 40
100 20
Allen wrench 5
Force
9.8 Nm / 7.2 lbft 0 0

--100 - 20
--200 - 40
- 60
--300
40 --6 --5 --4 --3 --2 --1 0
1.57 Stroke (mm)
DAU003E 87
With detent
9 kit 10 kit
1 0 2 1 0 2

6.6 Nm / 4.9 lbft 6.6 Nm / 4.9 lbft
9.8 Nm / 7.2 lbft 9.8 Nm / 7.2 lbft
49 44.5
1.93 1.75
Locking force (from pos. 0 to 1) . . . : 150 N / 33.7 lbf ±10% Locking force (from pos. 0 to 2) . . . : 150 N / 33.7 lbf ±10%
Release force (from pos. 1 to 0) . . . : 140 N / 31.5 lbf ±10% Release (from pos. 2 to 0) . . . . . . . : 140 N / 31.5 lbf ±10%
11 kit 12 kit
1 0 2 1 0 2
Allen wrench 4
Allen wrench 4
6.6 Nm / 4.9 lbft
6.6 Nm / 4.9 lbft
9.8 Nm / 7.2 lbft 9.8 Nm / 7.2 lbft
40 40
1.57 1.57
Locking and release force . . . . . . . . : 120 N / 27 lbf ±10% Locking and release force . . . . . . . . : 100 N / 22.5 lbf ±10%
15 kit 16 kit
1 0 0 2

6.6 Nm / 4.9 lbft 6.6 Nm / 4.9 lbft
9.8 Nm / 7.2 lbft 9.8 Nm / 7.2 lbft
40 40
1.57 1.57

Locking and release force . . . . . . . . : 100 N / 22.5 lbf ±10% Locking and release force . . . . . . . . : 100 N / 22.5 lbf ±10%
88 DAU003E
With detent and sprimg return to neutral position from either directions
9BZ kit
1 0 2 Port B Port A
2 0 1
- 0.2 - 0.1 0 0.1 0.2 (in)
300 (lbf)
(N) 60
- 0.22
0.13
0.22
6.6 Nm / 4.9 lbft 100 20
Force
0 0
--100 - 20
Detent area - 40
--200
- 5.5
3.3
5.5
- 60
76 --300
2.99 --6 --5 --4 --3 --2 --1 0 1 2 3 4 5 6
Stroke (mm)
Allen wrench 5
10BZ kit
1 0 2 Port B Port A
2 0 1
- 0.2 - 0.1 0 0.1 0.2 (in)
300 (lbf)
(N) 60
- 0.22
- 0.13
0.22
Allen wrench 4 200
40
6.6 Nm / 4.9 lbft 100 20
Force
Detent area
0 0
--100 - 20
--200 - 40
- 5.5
- 3.3
5.5
- 60
76 --300
2.99 --6 --5 --4 --3 --2 --1 0 1 2 3 4 5 6
Allen wrench 5 Stroke (mm)
11BZ kit
1 0 2 Port B Port A
2 0 1
- 0.2 - 0.1 0 0.1 0.2 (in)
(lbf)
300
(N) 60
- 0.19
- 0.22
0.13
0.22

6.6 Nm / 4.9 lbft 100 20
Force
Detent area Detent area

0 0
--100 - 20
--200 - 40
- 5.5
- 3.3
3.3
5.5
- 60
76 --300
2.99 --6 --5 --4 --3 --2 --1 0 1 2 3 4 5 6
Allen wrench 5 Stroke (mm)
DAU003E 89
With microswitch type 8MG3(NO)

With spring return in neutral position and microswitch operated in both directions.
Also available 8MG1(NO) configuration (microswitch operated in position 1) and 8MG2(NO) configuration (microswitch operated in
position 2); dimensions are the same of 8MG3 configuration.
Same configurations are available on request with normally closed (NC) contact.
Microswitch with connector 8MG3(NO) kit

Wrench 22
42 Nm / 31 lbft 1 0 2
Wrench 10
9.8 Nm / 7.2 lbft
Allen wrench 4 Other configurations

6.6 Nm / 4.9 lbft
8MG1(NO) kit 8MG2(NO) kit
1 0 2 1 0 2
70
Allen wrench 5
9.8 Nm / 7.2 lbft
COMPLETE CONTROLS CODE Operating features

MICROSWITCH
CONTROL TYPE Need Mechanical life . . . . . . . . . . . : 5x105 operations
Contact 8MG3 8MG2 8MG1 connector type Electrical life (resistive load) : 105 oper. -- 7A / 13.5VDC
: 5x104 oper -- 10A / 12VDC
see page
NO 5V08104660 5V08104680 5V08104670 C07
129 : 5x104 per -- 3A / 28VDC

It’s possible to obtain further configurations of complete control, using the MG kit, microswitches and 3 positions “A” side spool posi-
tioner, as following draw.
With NO contact With NC contact

Microswitch code: 4MIC730 code: 4MIC740
84,5 128
3.33 5.04
PACKARD W--PACK PACKARD W--PACK

female connector male connector with
with male end female end
Kit MG3 Kit MG1 Kit MG2

code: 5KIT820400 code: 5KIT820401 code: 5KIT820402
3 positions “A” side spool Kit MG-- ED

positioner type 9B, 10B, 11B for
left inlet directional valve.
(see page 23)
90 DAU003E
Solenoid lock device

It’s possible to obtain further configurations of complete control, using the kit K--ED (for right inlet directional valve), coils and 3 posi-
tions “A” side spool positioner for left inlet directional valve, as following draw: for information contact Sales Department.
COILS CODE
Coils
CONNECTION TYPE
12 VDC 2X4300012 2X4300014 YSOL300013
24 VDC 2X4300024 2X4300026 YSOL300025
Need
3 positions “A” side spool connector type C02 C19 C20
positioner type 8, 9B, 10B, 11B for (see page 129)
left inlet directional valve.
(see pages 20 and 23)
Kit K-- ED
Fitted with actuator:
code: 5KIT810400
Operating features
ACTUATOR
Lock stroke . . . . . . . . . . . . . . . . . . . . . : 3.5 mm / 0.14 in
COIL
Depending on model: see following features
Coil with ISO4400 connector Coil with Deutsch DT connector Coil with Packard M-- Pack connector
634
25
Nom. voltage tolerance . : ±10% Nom. voltage tolerance . : ±10% Nom. voltage tolerance . : ±10%
Nominal current . . . . . . . . : 1.58 A -- 12 VDC Nominal current . . . . . . . . : 1.9 A -- 12 VDC Nominal current . . . . . . . . : 1.58 A -- 12 VDC
: 0.81 A -- 24VDC : 0.95 A -- 24VDC : 0.81 A -- 24VDC
Coil insulance . . . . . . . . . : Class F Coil insulance . . . . . . . . . : Class H Coil insulance . . . . . . . . . : Class F
DAU003E 91
ON/OFF electropneumatic kit type 8EP3
Wrench 14 -- 9.8 Nm / 7.2 lbft Scheme

Pg9 43 60.5 V1 V2
1.69 2.38
1 0 2
113.5
4.47
Scheme ISO 1219

V1 V2
1 0 2
0.24
6
1.65
42
V1 V2
122.5
4.82
Allen wrench 4
Wrench 9 Special wrench -- 9.8 Nm / 7.2 lbft
6.6 Nm / 4.9 lbft
Operating features
CONTROL
COMPLETE CONTROL CODES
Pilot pressure . . . . . . . . . . . . . . : 6 bar / 87 psi
: (max.10 bar / 145 psi)
CONNECTION TYPE
COIL
ISO6952 Flying leads
CONTROL TYPE Power rating . . . . . . . . . . . . . . . : 8 W
Voltage 8EP3 8EP35 Nominal current . . . . . . . . . . . . . : 0,67 A -- 12 VDC
12 VDC 5V08104735 5V08104736 : 0,33 A -- 24VDC
Coil insulation . . . . . . . . . . . . . . : Class F
24 VDC 5V08104740 5V08104741
Weather protection . . . . . . . . . . : IP65
Need
C01 Duty cycle . . . . . . . . . . . . . . . . . : 100%
connector type /
(included)
(see page 129)
Coil with ISO6952 Coil with flying leads

connector
COIL CODES
200
7.87
CONNECTION TYPE
Voltage
ISO6952 Flying leads*
12 VDC 2X4000013 2XB1000120000
24 VDC 2X4000025 2XB1000240000
* Several type of connectors can be wired on request
92 DAU003E
ON/OFF pneumatic kit type 8P

Wrench 11 -- 9.8 Nm / 7.2 lbft With spring return to neutral position.
NPT 1/8” -- nr.2 thread
55
Allen wrench 4
6.6 Nm / 4.9 lbft
2.16 1 0 2
V2
0.91
23
V1 V2
V1 Operating features
Pilot pressure . . . . . . . . . . . . : min. 5.5 bar / 80 psi
: max. 10 bar / 145 psi
121.5
4.78
Wrench 10 -- 9.8 Nm / 7.2 lbft Allen wrench 4 -- 6.6 Nm / 4.9 lbft

Allen wrench 4 -- 6,6 Nm / 4.9 lbft With external pilot and drain.
142.5
5.61 Scheme
42 62.5 1
1.65 2.46 L
6.6 Nm -- 4.9 lbft V
Coil 1 0 2
Solenoid valve:
wrench 24 -- 9.8 Nm / 7.2 lbft
Scheme ISO 1219
133
Special wrench -- 9.8 Nm / 7.2 lbft

1 0 2
Collector
V L
119.5
4.70
136.5
5.37
Wrench 10 Allen wrench 4 -- 6.6 Nm / 4.9 lbft
COMPLETE CONTROL CODES Operating features
CONTROL
CONNECTION TYPE Pilot pressure . . . . . . . . . . . . . . : min. 10 bar / 145 psi
AMP JPT : max. 50 bar / 725 psi
ISO4400 Deutsch DT Max backpressure on drain L . : 25 bar / 360 psi
without diodo with diodo
COIL
CONTROL TYPE
Voltage 8ED3 8ED32 8ED32D 8ED34
Power rating . . . . . . . . . . . . . . . : 21 W
12 VDC 5V080104350 5V08104250 5V08104280 5V08104450 Nominal current . . . . . . . . . . . . . : 1.75 A -- 12 VDC
24 VDC 5V08104351 5V08104251 5V08104281 5V08104451 0.87 A -- 24VDC
Need Coil insulation . . . . . . . . . . . . . . : Class F
connector type C02 C08 C08 C19 Weather protection . . . . . . . . . . : IP65
(see page 129)) Duty cycle . . . . . . . . . . . . . . . . . : 100%
DAU003E 93
COIL CODES
CONNECTION TYPE
AMP JPT
ISO4400 Deutsch DT
Voltage without diodo with diodo
12 VDC 2XB1400121100 2XB1400121200 2XB1400121210 2XB1400120400
24 VDC 2XB1400241100 2XB1400241200 2XB1400241210 2XB1400240400
Coil with Coil with Coil with Deutsch DT connection

ISO4400 connection AMP JPT connection
170
6.69
Collector kit for external pilot and drain
B2 A2 B1 A1
L
V
L V
20 bar
6.06
290 psi
154
T
Collector
P
P
T
120
1750
COLLECTOR KIT CODES
Type Code * Description

KE1S0 5KE1S00030 Kit one section
SD5/2--P(JG3--120)/ED--18ED3L/ED--18ED3L/AET--
KE2S0--24VDC
(*) codes are referred to BSP thread
94 DAU003E

Collector kit with pilot and drain lines
The kit is made of collector, VRP pressure reducing valve and pipes.
Wrench 19 -- 24 Nm / 17.7 lbft VRP

136 28 B2 A2 B1 A1
5.35 1.10
Collector L
Allen wrench 6
24 Nm / 17.7 lbft
Wrench 17
VRP Code:
Drain line 2S100808VAL21
6.06
154
35 Inlet line
1.38 P
P
VRC
T 120
1750
Wrench 22
24 Nm / 17.7 lbft
VRC backpressure
valve (not included)
Description example: COLLECTOR KIT CODES

SD5/2--P(JG3--120)/ED--18ED3L/ED--18ED3L/
Tipo Code * Description
VRC--KE2R3--24VDC
KE1R0 5KE1R30230 Kit one section
Operating features
VRP VALVE
Output pressure . . . . . . . . . . . . : 20 bar / 290 psi KE4R0 5KE4R30230 Kit for 4 sections
Max flow . . . . . . . . . . . . . . . . . . : 8 l/min KE5R0 5KE5R30230 Kit for 5 sections
Filtering . . . . . . . . . . . . . . . . . . . : 80 µ KE6R0 5KE6R30230 Kit for 6 sections
(*) Codes are referred to BSP thread
VRC valve: code X003600010

Valve assembled on flow through passage provides pilot pressure to the actuator.
Pressure drop P→T

Wrench 22 40
(psi)
42 Nm / 31 lbft (bar)
30
400
Pressure
Wrench 22 20
24 Nm / 17.7 lbft 200
10
20
0.79 0
0 15 30 45
Flow (l/min)
DAU003E 95

13QN kit
Detent in 4th position with spool out:available only for spool type ED--5PY (see page 84).
Port B Port A Floating

2 0 1 3
- 0.1 0 0.1 0.2 0.3 (in)
Allen wrench 4
400 (lbf)
6.6 Nm / 4.9 lbft
- 0.18
0.18
(N)
60
0.27
Wrench 6 200
9.8 Nm / 17.7 lbft 30
Forza
0 0
- 30
--200
- 60
- 4.5
4.5
6.8
76 --400
2.99 --5 --4 --3 --2 --1 0 1 2 3 4 5 6 7 8 9
Detent area
96 DAU003E
Outlet port options
It’s possible to have open centre, closed centre and carry--over.
Unloader valves are available: these valves need special bodies with appropriate cavity on lateral outlet port, the tank connection
T must be on top.
AET: open centre (standard)

See page 79.
AE:with carry--over AEK: closed centre

20.5 2.5
0.81 0.098
G3/8
C Allen wrench 8
42 Nm / 31 lbft
Wrench 22
42 Nm / 31 lbft
B2 A2 B1 A1 B2 A2 B1 A1
T T
P P
C
120 120
1750 1750

SD5/2--P(KG3--120)/ED--18L/ED--18L/AE SD5/2--P(KG3--120)/ED--18L/ED--18L/AEK
With hydraulic pilot unloader valve type L

For safety reasons it’s provided with pilot port plugged.
B2 A2
T
Wrench 24 -- 42 Nm / 31 lbft Pressure drop curve
12 (psi)
(bar) X
150
G1/4
9
Pressure
X 100
6
3 50
10
0.39
0
0 10 20 30 40 45
Flow (l/min) Description example:
Operating features SD5/2--P(JG3--120)/ED--18L/ED--18L/AET--L
Internal leakage . . . . . . . . . . . . . . . . . : 10 cm3/min a 100 bar
: 0.61 in3/min at 1450 psi
DAU003E 97
Outlet port options

With push and twist button for manual ovverride with detent.
Codes show at page 81 are referred to valves with ISO4400 coil, for complete valves with different electric connection contact
Sales Department.
Spare coils with several connectors are available, with and without diode.
Wrench 30 -- 42 Nm / 31 lbft Pressure drop

Push and twist push--but- 25 (psi)
ton for manual override (bar)
20 300
Pressure
15 200
10
100
5
123
4.84 0
0 20 40 60
Flow (l/min)
Oerating features
VALVE
Internal leakage (excited position) : max. 75 cm3/min at 100 bar . .
: max . 4.6 in3/min at 1450 psi
COIL
Depending on model: see following page
Normally open configuration type EL Normally closed configuration type ELC
T B2 A2 T B2 A2

SD5/2--P(JG3--120)/ED--18L/ED--18L/AET--EL--12VDC SD5/2--P(JG3--120)/ED--18L/ED--18L/AET--ELC--12VDC
98 DAU003E
Outlet port options
COIL CODES
CONNECTION TYPE
AMP JPT
ISO4400 Deutsch DT
Voltage senza diodo con diodo
12 VDC 2X4311012 2X4311015 2X4311212 2X4311412
24 VDC 2X4311024 - - 2X4311424
Coil with ISO4400 connector Coil with AMP JPT connector Coil with Deutsch DT connector
Connector side Connector side Connector side
Nominal voltage tolerance: ±10% Nominal voltage tolerance: ±10% Nominal voltage tolerance: ±10%
Nominal current . . . . . . . . : 1,58 A -- 12 VDC Nominal current . . . . . . . . : 1,3 A -- 12 VDC Nominal current . . . . . . . . : 1.76 A -- 12 VDC
: 0,81 A -- 24VDC : 0,74 A -- 24VDC : 0.9 A -- 24VDC
Coil insulation . . . . . . . . . : Classe F Coil insulation . . . . . . . . . : Classe F Coil insulation . . . . . . . . . : Classe H
NOTE: circuit with and without bidirectional NOTE: circuit with bidirectional diode
diode
LT: unloader valve prearrangement
T
A2 B2
Allen wrench 6
24 Nm / 17.7 lbft
SD5/2--P(JG3--120)/18L/18L/AET--LT
DAU003E 99
Srvice and auxiliary valves10.

All service and auxiliary valves need special body: contact Sales Department.
VS
1.
Relef valve
Mounting on the opposite

side of working ports

Relef valve (fixed setting)
2. 3.
Kit VS VM(...)
VSC(JG...)
Kit VM
VMT
VM(...)
VSCT
VMT
4.
Flow control valves
VP
5.
VU
Kit V
VC Kit VD1 VD21
VP
VT
VU
VD22
VC
VT VD23
100 DAU003E
1. Relief valves page 102 4. V anti--schock+anti--cavitation valve page 106

TYPE CODE DESCRIPTION Set of valves fitted with mounting block.
VS(G3-- 100) 3XCAR505113 Range 40 to 200 bar / 580 to 2900 psi TYPE CODE DESCRIPTION
standard setting 100 bar / 1450 psi Kit V 5CO2820010 Mounting block kit
VST 3XTAP419300 Valve blanking plug T XTAP524280 Valve blanking plug
C 5KIT406110 Anti--cavitation valve
Anti--shock valves
2. Flange mounted relief valve page 103 P(G2) 5KIT206112 Range 60 to 125 bar / 870 to 1800 psi
Anti--shock + anti--cavitation valves
VSCT XTAP623282 Valve blanking plug
Kit VS 5CO2420000 Mounting block kit
3. VM anti--schock+anti--cavitation valve page 104
Flange mounted type with fixed setting and fitted with mounting block.
TYPE CODE DESCRIPTION 5. Flow control valves page 110
Flow control on every section; with auxiliary inlet
VD21 2S0PP10002000 Fine regulation from 3 to 28 l/min
VD22 2S1636020211 As VD11, one turn with detent
VD23 2S0PP10002002 12VDC proportional solenoid valve
Kit VD2 5CO2822020* Mounting block kit
VMT XTAP221340 Valve blanking plug
Kit VM 5CO2820020 Mounting block kit
NOTE -- Valve setting at points 1--2--4--5--6 are referred to 10 l/min flow.

NOTE -- (*) Codes are referred to BSP threads.
DAU003E 101
VS relief valve
It’s suggested for flow up to 25 l/min, and it’s mounted on parallel body to limitate the pressure, at lower value than main relief valve
(min. gap 20 bar / 290 psi ), on downstream section.
It’s in parallel with flow trough and it works only with single operation.
VS ( G 3 -- 100 )
Pressure setting in bar (standard 100 bar / 1450 psi)

Spring type
Adjustment type
T
P C Allen wrench 3
max.
Wrench 10
B2 B1 9.8 Nm / 7.2 lbft
24.5
0.96
0.55
14
Wrench 17
24 Nm / 17.7 lbft
C
Wrench 19
24 Nm / 17.7 lbft
C -- C C -- C
18.5 18.5
0.73 0.73
Performance data
Hydraulic circuit
Spring nr. 3 (blue band)
B2 A2 B1 A1
400
(bar) (psi)
T 300 4500
Pressure
200 3000
P
100 1500
100 0
1450 120 0 10 20 30
1750
Flow (l/min)
SD5/2--P(KG3--120)/ED--18L/VS(G3--100)/ED--18L/AET--PSA Time response
(% ∆P)
105%
VST: valve blanking plug
95%
Pressure
1450 psi
Allen wrench 6 90%

100 bar
42 Nm / 31 lbft
10%
0.16
4
0,08” Time (”)

TIME RESPONSE
102 DAU003E
VSC relief valve

It’s flange mounted on parallel body on the opposite side of working ports, the function to limit the pressure, at lower value than main
relief valve (min. gap 20 bar / 290 psi) on downstream sections.
It’s in parallel with flow through line and it works only with single operation.
B2 A2 B1 A1
1
T
2 3
120
1750
VSC ( J G 3 -- 100 )
Standard setting in bar 100
1450
Adjustable spring type (2, 3, 4). Description example:
Adjustment type (G, H). SD5/2--P(JG3--120)/ED--18L/VSC(JG3--100)/ED--18L/AET
37 53
1.46 2.09
Wrench 4
6.6 Nm / 4.9 lbft
A2 A1
54.5
2.15
P
max. 106
max. 4.17
T
1.34
34
B2 B1
NOTE -- For performance

data, wrench and
tightening force, please
13
see page 12. 0.51
21.5
0.85 32 24.5
43 37.5 1.26 0.96
1.69 1.48
DAU003E 103

They are flange mounted on the opposite side of working ports, connected in parallel with A and B ports and with outlet on T port.
It needs a dedicated body with extra machining: for production requirements, the block (2) is flanged on body (1) before the final
honing of spool hole, while the valve (3) is mounted during final assembling phase.
Valve on port A
Valve on port B
2 3
37 53
1.46 2.09
13.5
0.53
A2 A1
5.5
0.22
T
3.39
86
B2 B1
0.55
14
27.5
1.08
15.3 40.5 24.5

0.60 1.59 0.96
36.6 21.9
1.44 0.86
104 DAU003E
VM 1 (100) VM1 VM2 VM3
Valve setting in bar A B A B A B

1 mounted on port A T T T
2 mounted on port B
3 mounted on ports A and B
100 100
1450 1450
100 100
1450 1450
Example of VM1 configuration
Pressure--flow diagram
350 (psi)
(bar)
300 4500
250
T 200 3000
Pressure
150
100 1500
50
Allen wrench 6
24 Nm / 17.7 lbft 0
0 10 20 30 40 45
Flow (l/min)

6.6 Nm / 4.9 lbft 24 Nm / 17.7 lbft
DAU003E 105

They are anti--shock (VP), anti--shock and anti--cavitation (VU) and anti--cavitation (VC) service valves, flange mounted on the
opposite side of working ports connected in parallel with A and B ports.
They need a dedicated body with extra machining: for production requirements, the blocks (2) are flanged on body (1) before the
final honing of spool hole, while the valves (3) are mounted during final assembling phase.
For information contact Sales Department
Valve on port A Valve on port B
3 2 2 3
37 53
1.46 2.09
VP VU VC VT
14 / 0.55 14 / 0.55
9.5 / 0.37 5.5 / 0.22
max. max.
A2 A1
P
0.079
2
T
32.5
1.28
T
57.5
2.26
B2 B1
D
16
0.63
1 18 35 25
0.039 0.71 1.38 0.98
36 22.5
1.42 0.89
106 DAU003E
V anti-- schock+anti-- cavitation valves

Anti-- shock valve
VP1 VP2 VP3
VP 1 ( G 3 - 100 ) T A B T T A B T

Spring type (2, 3, 4). 100 100 100 100
1450 1450 1450 1450
Adjustment type
T T
Notch
1.5 mm / 0.06 in
Wrench 22
42 Nm / 31 lbft Allen wrench 5
9.8 Nm / 7.2 lbft
Performance data
400 (psi) 400 (psi)

(bar) (bar)
300 4500 300 4500
Pressure
Pressure
200 3000 200 3000
100 1500 100 1500
0 0
0 20 40 60 0 20 40 60
Spring nr.4 (red band)

Time response
400 (psi) (% ∆P)
(bar)
105%
300 4500
Pressure
95%
Pressure
200 3000 90%

1450 psi
100 bar
100 1500
10%
0
0 20 40 60 Time (”)
0,02”
Flow (l/min) TIME RESPONSE
DAU003E 107

Anti-- shock + anti-- cavitation valve
VU1 VU2 VU3
VU 1 ( G 3 -- 100 ) T A B T T A B T

Spring type (2, 3, 4). 100 100 100 100
1450 1450 1450 1450
Adjustment type
T T
Notch
1.5 mm / 0.06 in
Wrench 22
42 Nm / 31 lbft Allen wrench 5
9.8 Nm / 7.2 lbft
Performance data
400 (psi) 400 (psi) 400 (psi)

(bar) (bar) (bar)
300 4500 300 4500 300 4500
Pressure
Pressure
Pressure
200 3000 200 3000 200 3000
100 1500 100 1500 100 1500
0 0 0
0 20 40 60 0 20 40 60 0 20 40 60
Pressure drops Time response
150 (psi)
(% ∆P)
(bar) 2000
120 105%
1500
Pressure
90 95%
Pressure
90%
1750 psi
1000
120 bar
19.5 bar / 280 psi

60
OPENING PEAK
30 500
10%
0
0 20 40 60 0.1” 0.15” Time (”)
Flow (l/min) TIME REPONSE TRANSITORY
108 DAU003E

Anti-- cavitation valve
VC1 VC2 VC3
VC 1 A T T B T B A T
Perdita di carico
120
(bar)
90
Pressione
60
30
0
0 20 40 60
Wrench 24 Portata (l/min)
42 Nm / 31 lbft
Allen wrench 5
9.8 Nm / 7.2 lbft
Valve blanking plug VT1 VT2 VT3

A T T B T B A T
VT 1
Allen wrench 8
24 Nm / 17.7 lbft
Allen wrench 5
9.8 Nm / 7.2 lbft
DAU003E 109

Block with pressure compensated 3--way flow control valve, to be flange mounted on body with parallel circuit.
The cavity is oriented toward lever side.
The flow is regulated on every working section while the exceeding flow goes to tank: max. regulated flow 28 l/min (with inlet on P1
port).
P1
2 3
40.5 35 24.5
1.59 1.38 0.96
G3/8
13.4
0.53
P1
0.53
13.5
T
A2 A1
P
3.15
80
T
D
B2 B1
17.5
0.69
45 18
VD21 VD22 VD23
1.77 0.71
124 / 4.88 174.5 / 6.87 174.5 / 6.87
110 DAU003E

Manual control
VD21: continuous fine regulation
P1
Hydraulic circuit
6.6 Nm / 4.9 lbft 24 Nm / 17.7 lbft B1 A1
Description example: SD5/2--P(JG3--120)VD11/ED--18L/ED--18L/AET
120
VD22: one turn with detent handknob regulated 1750
P1
C
R
P1

6.6 Nm / 4.9 lbft 24 Nm / 17.7 lbft
DAU003E 111

VD13 with proportional solenoid control
Hydraulic circuit
B1 A1
ISO4400 connection
(needs C02 connector,
see page. 129)
T
P
120
1750
P1
P1
C
R
6.6 Nm / 4.9 lbft 24 Nm / 17.7 lbft
Proprtional solenoid flow control valve connection

It’s shows a configuration with push--button panel type UPA.
Emergency Potentiometer for

push--button valve adjustment
Solenoid operating feautures
Nominal voltage . . . . . . . . . : 12 VDC
Power rating . . . . . . . . . . . . : 28 W
Duty cycle . . . . . . . . . . . . . . : 100%
STOP
ISO4400
connec tor
To battery
Push--button panel type:
UPA12/100/SC01B22
Performance data
1000 2000 3000 (psi) 0 0.3 0.6 0.9 1.2 Current (A)
40 (l/min) 40
(l/min)
30 30
Priority flow
Priority flow
F J F VD11 flow control valve

20 20 Y VD12 flow control valve
Y
J VD13 flow control valve
10 10
0 0
30 90 150 210 270 0.0 0.5 1.0 1.5 2.0 2.5 (n.of turn)
Pressure (bar)
0 3 6 9 12 15 18 (n.of clicks)
112 DAU003E
Other executions
SD5/1- N . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . page 114

cuits where carry--over doesn’t required.
lel circuit.
SD5/1- D . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . page 115

cuits where carry--over is required.
H Configurations with service and auxiliary valves aren’t available
SD5- S: with series circuit . . . . . . . . . . . . . . . . . . . . . . . . . . . page 116

Available from 2 to 6 sections, it can be used in systems wich one downstream
section from series connection must work with upstream ones at the same time.
H It’s not available the carry--over circuit.
lel circuit.
SD5- SP: with tandem circuit . . . . . . . . . . . . . . . . . . . . . . . . page 118

Available from 2 to 6 sections, for security reasons it can be used in systems
which is required to prohibit engagement of downstream sections from tandem
connection when the upstream sections are working.
lel circuit.
SDM105: with flow control valve . . . . . . . . . . . . . . . . . . . page 120

Available from 1 to 6 sections, with parallel circuit
H It can be configured with unloader valve.
H Configurations with service and auxiliary valves aren’t available.
DAU003E 113
SD5/1--N directional valve with right inlet
Dimensional data
63.5 5
27 30 24.5 2.50 0.20
1.06 1.18 0.96 45
1.77
1.81
46
0.45
11.5
0.33
8.5
45.5
1.79
2.01
51
193.5
7.62
4.06
103
3.19
81
1.35
34
spool out
3
1
24°
M8
0.79
15°
20
0
15°
24°
2
73 14 24.5
2.87 0.55 0.96 3
90
105.5 spool in
3.54
4.15

Pressure drop curve
B1 A1
15 (psi)
(bar) 200
10 150
P P→A(B)
T
Pressure
100
P→T
5
50
120
1750 A(B)→T
0
0 15 30 45 60
Description example Flow (l/min)
SD5/1--N(JG3--120)/ED--18L
Code: 102110033
114 DAU003E
directional valve with right inlet SD5/1--D
Dimensional data
63.5 5
27 30 23.5 2.50 0.20
1.06 1.18 0.93 45
1.77
1.81
46
0.45
11.5
0.33
8.5
45.5
1.79
2.01
51
193.5
7.62
103
4.06
3.19
81
1.34
34
spool out
3
1
24°
M8
0.79
15°
20
0
15°
24°
2
73 13 24.5
2.87 0.51 0.96 3
90
102 3.54 spool in
4.02
A1 B1 Pressure drop curve
20 (psi)
(bar) 200
T
15
150
P P→A(B)
C 10
Presure
100
P→C
5 50
120
1750 A(B)→T
0
0 15 30 45 60
SD5/1--D(JG3--120)/ED--18L
Code: 102160027
DAU003E 115
SD5--S directional valve with right inlet
Dimensional data
63.5 5
2.5 0.20
27 37 30 23 45
1.06 1.46 1.18 0.91 1.77
1.77
45
11,5
0.33
8.5
45.5
1.79
51
193.5
7.62
4.06
103
81
1.34
34
spool out
3
1
24°
M8
0.79
20
15°
0
15°
24°
2
F 12.5 24.5
0.49 0.96 3
E 90
3.54 spool in
TYPE TYPE
SD5/2--S 137.5 5.41 110 4.33 5.2 11.4 SD5/5--S 248.5 9.78 221 8.70 10.1 22.3
SD5/3--S 174.5 6.87 147 5.79 6.9 15.2 SD5/6--S 285.5 11.2 258 10.2 11.7 25.8
SD5/4--S 211.5 8.33 184 7.24 8.1 17.9
116 DAU003E
directional valve with right inlet SD5--S
Hydraulic circuit
The description of SD5 valve with series circuit is marked with letter “S” and one figure wich indicate the downstream sections from
series connection.
B4 A4 B3 A3 B2 A2 B1 A1
CODE DESCRIPTION
5KC1153040 SD5/2--S1
5KC1253003 SD5/3--S1
P
T 5KC12D3000 SD5/3--S1+1
5KC1283003 SD5/4--S1
5KC12E3000 SD5/4--S1+1+1
5KC1324033 SD5/5--S1
120 5KC1073001 SD5/5--S1+1+1+1
5KC13A3000 SD5/5--S2+1
5KC1363003 SD5/6--S1
Description example: Include boby, seals and load check
SD5/4--S1(JG3--120)/ED--18L/ED--18L/ED--18L/ED--18L valves.
NOTE (*) -- Codes are referred to BSP thread.
Performance data
40 40
P→A6(B6)
30 6 sections 450 30 450
4 sectionis
Pressure
Pressure
20 300 20 300
10 150 10 150
0 0
0 15 30 45 60 0 15 30 45 60
Pressure drop
Pressure drop A(B)→T between port A(B) before series
on 6 sections directional valve connection and port A(B) after
40 40
(bar) (psi) (psi)
A1(B1)→T (bar)
30 450 30 450
Pressure
300 300
Pressure
20 20
A6(B6)→T
10 150 10 150
0 0
0 15 30 45 60 0 15 30 45 60
DAU003E 117
SD5--SP directional valve with right inlet
Dimensional data
Carry--over
20,5 63.5 5
2.50 0.20
27 37 30 23 45.5
1.06 1.46 1.18 0.91 1.79
1.77
45
0.33
0.45
11.5
8.5
45.5
1.79
2.01
51
193.5
7.62
3.19
103
81
4.06
1.34
34
spool out
3
1
M8 24°
0.79
20
15°
0
15°
24°
2
F 12.5 24.5
0.49 0.96
E 90 3
3.54 spool in
TYPE TYPE
SD5/2--SP1 137.5 5.41 110 4.33 4.8 10.6 SD5/5--SP4 248.5 9.78 221 8.70 10.2 22.5
SD5/3--SP2 174.5 6.87 147 5.79 6.7 14.8 SD5/6--SP5 285.5 11.2 258 10.2 11.3 24.9
SD5/4--SP3 211.5 8.33 184 7.24 8.1 17.6 SD5/7--SP6 322.5 13.1 295 11.6 12.7 28
118 DAU003E
directional valve with right inlet SD5--SP
Hydraulic circuit
The description of SD5 valve with tandem circuit is marked with letters “SP” and one figure wich indicate the downstream sections
from tandem connection.

CODICE DESCRIZIONE
B4 A4 B3 A3 B2 A2 B1 A1 5KC1183000 SD5/2--SP1
5KC12G3000 SD5/3--SP2
5KC1303000 SD5/4--SP1
T
5KC12H3000 SD5/4--SP1+1
5KC12I3000 SD5/4--SP2+1
P 5KC1293000 SD5/4--SP3
5KC13D3000 SD5/5--SP2+2
5KC1343000 SD5/5--SP3+1
5KC1333000 SD5/5--SP4
5KC1393000 SD5/6--SP3+1
120 5KC13Y3000 SD5/6--SP3+2
1750
5KC1373000 SD5/6--SP5
5KC13I3000 SD5/7--SP3+1
Description example: 5KC13G3000 SD5/7--SP4
SD5/4--SP3(JG3--120)/ED--18L/ED--18L/ED--18L/ED--18L/AET 5KC13L3000 SD5/7--SP5+1
5KC13F3000 SD5/7--SP6
valve.
Performance data
40 40
30 6 sections 450 30 450

P→A6(B6)
4 sections
Pressure
Pressure
20 300 20 300
10 150 10 150
0 0
0 15 30 45 60 0 15 30 45 60

40
(bar) (psi)
A1(B1)→T
30 450
Pressure
20 300
A6(B6)→T
10 150
0
0 15 30 45 60
Flow (l/min)
DAU003E 119
SDM105 directional valve with right inlet
Dimensional data
63.5 5
47.5 37 30 23 2.50 0.20
45
1.87 1.46 1.18 0.91
1.77
0.45
11.5
34.5
1.36
193.5
7.62
4.06
103
3.19
81
1.34
34
0.33
8.5
spool out
1.18
30
3
0.51
13
1
24°
0.79
10.5
0.41
20
15°
0
1.73
44
M 10
15°
24°
2
15 110 12.5 24.5
0.59 4.33 0.49 0.96 3
137.5 96 spool in
3.78
5.41
TYPE TYPE
SDM105/1 137.5 5.41 110 4.33 5.1 11.2 SDM105/4 248.5 9.78 221 8.70 9.9 21.8
SDM105/2 174.5 6.87 147 5.79 6.7 14.8 SDM105/5 285.5 11.24 258 10.16 11.6 25.6
SDM105/3 211.5 8.33 184 7.24 8.3 18.3 SDM105/6 322.5 12.70 295 11.61 13.3 29.3
120 DAU003E
directional valve with right inlet SDM105
Hydraulic circuit
Compensator rear plug
Positioner kit
B1 A1 Port B line Main relief valve
Compensator
spool
T
P P
Flow through
(LC)
T
120 Pressure line
1750
Description example: Tank line

SDM105/1(JG3--120)M/110L/LT Flow control with
Port A line
wheel regulation
Lever pivot box
Compensator front plug
Performance data
20 (psi) 20 (psi)
(bar) (bar)
240 P→A4(B4) 240
15 4 sections 15
P→A2(B2)
Pressure
Pressure
2 sections 160 P→A1(B1) 160

10 10
1 section
5 80 5 80
0 0
0 15 30 45 60 0 15 30 45 60

20 (psi)
(bar)
240
15
A1(B1)→T
160
Pressure
10
A4(B4)→T
5 80
0
0 15 30 45 60
Flow (l/min)
DAU003E 121
Ordering codes
Valve setting in bar
SDM105 / 1 -- P (JG3-- 120) M / 2 10 L / EL-- 12VDC - ........
1. 2. 3. 5. 6. 7. 9. 10.
SDM105 / 1 - P (JG3-- 120) M / 18ES3 / LT - 12VDC
8.
2.
4. 10.
3.
6.
I
9. 1.
5.
7.
1. Body kit * 2. Inlet relief options page 12

1-- P 5KC5013000 Parallel, 1 section VMD5 direct pressure relief valve type J
2-- P 5KC5023000 Parallel, 2 sections Standard setting is referred to 10 l/min flow.
3-- P 5KC5033000 Parallel, 3 sections (JG2-- 63) 5KIT105412 Range 40 to 63 bar / 580 to 900 psi
4-- P 5KC5043000 Parallel, 4 sections standard setting 63 bar / 900 psi
5-- P 5KC5053000 Parallel, 5 sections (JG3-- 120) 5KIT105413 Range 50 to 200 bar / 725 to 2900 psi
6-- P 5KC5063000 Parallel, 6 sections standard setting 120 bar / 1750 psi
Include boby and seals.
SV XTAP623282 Relief valve blanking plug
122 DAU003E
Ordering codes
3. Flow controls page 124 7. “B” side options page 39

M XCAR705211 Continuous fine wheel regulation L 5LEV205000 Lever box for M10 handlever
G XCAR705202 Screw regulation with locking nut (for dimensions see LM10 for SD5
directional valve)
SLP 5COP105000 Witout lever box, with dust--proof plate
4. Compensator kit TQ 5TEL105110 Flexible cable connection
-- 5CAS316065 Compensator kit
8. Complete controls page 46
ON/OFF solenoid control type 8ES.
5. Spool options page 125
9. Solenoid pilot unloaer valve page 98
1 3CU1210730 Double acting, 3 positions, with A and B
closed in neutral position TYPE CODE DESCRIPTION
2 3CU1225730 Double acting, 3 positions, with A and B EL-- 12VDC YCAR405305 With 12VDC electric control unloader
open to tank in neutral position valve; normally open circuit
Special spools for particular positioner kits . . . . . . . . . . . . . . . page 14 EL-- 24VDC YCAR405310 As previous 24VDC
5T 3CU1243701 Double acting, 4 positions, floating circuit ELC-- 12VDC 5CAR405330 With 12VDC electric control unloader
in 4th position with spool out. valve; normally closed circuit
ELC-- 24VDC 5CAR405331 As previous 24VDC
LT XTAP523370 Valve blanking plug
6. “A” side spool positioners page 86
8 5V08104000 With spring return in neutral position
10. Inlet and outlet selection * page 79
8D 5V08104200 With spring return in neutral position and TYPE CODE DESCRIPTION
pin with M6 female thread for dual control PSL 3XTAP722160 Side ports; need n.2 G 3/8 plugs, standard
8D2 5V08104220 With spring return in neutral position and configuration (omit in valve description)
pin with M8 male thread for dual control PSA 3XTAP722160 Upper ports; need n.2 G 3/8 plugs
8F2 5V08104101 With spring return in neutral position and
adjustable flow limiter
19 5V19104000 2 positions, with spring return in neutral
I Optional handlevers
position from position 1 TYPE CODE DESCRIPTION
20 5V19104000 2 positions, with spring return in neutral AL01/M10x150 170012015 For lever L:
position from position 2 height 150 mm / 5.91 in
in neutral position
in neutral position
11 5V11104000 Detent in positions neutral, 1 and 2
12 5V12104000 Detent in positions 1 and 2
neutral
neutral
in neutral position
in neutral position
11BZ 5V11204010 Detent in positions 1 and 2 and spring
return in neutral position
8MG3 5V08104660 With spring return in neutral position and
microswitch in positions 1 and 2
8P 5V08104701 ON/OFF pneumatic kit
8EP3 5V08104735 ON/OFF 12 VDC electro--pneumatic kit
5V08104740 ON/OFF 24 VDC electro--pneumatic kit
8ED3 5V08104350 ON/OFF 12 VDC electro--hydraulic kit
5V08104351 ON/OFF 24 VDC electro--hydraulic kit
Particular positioner kits for special spools . . . . . . . . . . . . . . . page 96
13QN 5V13404020 4 pos. with spring return in neutral pos.
and detent in 4th pos.: for spool 5T
DAU003E 123
Flow controls
Pressure compensated flow control with max. regulated flow = 45 l/min.
Type M Type G
Continuous fine wheel regulation Continuous screw regulation with locking nut.
∅ 26.5
∅ 1.04
Allen wrench 4
1.59 max.
40.5 max.
1.40 min.
35.5 min.
1.26 max.
32 max.
Wrench 13
1.06 min.
27 min.
24 Nm / 17.7 lbft
Wrench 22 Wrench 22
24 Nm / 17.7 lbft 24 Nm / 17.7 lbft

1000 2000 3000 (psi)
60 60
(l/min) (l/min)
45 45
Priority flow
Priority flow
30 30
15 15
0 0
30 90 150 210 270 0 1 2 3 4 5
Pressure (bar) nr. of turns
124 DAU003E
Spool options
Type 1
1 0 2
A B + 5,5 mm / 0.22 in
A B
(1) "
(0)
A (2)
LC T P T P T
-- 5,5 mm / 0.22 in
Type 2
1 0 2
A B + 5,5 mm / 0.22 in
A B
(1) "
(0)
A (2)
LC T P T P T
-- 5,5 mm / 0.22 in
Type 5T
This spool must be coupled with positioner type 13QN (see page 96).
+ 9 mm / 0.35 in
(3) " " 3 1 0 2
A B
A B
(1) " + 4.5 mm / 0.18 in
(0)
A (2)
LC T P T P T
-- 4.5 mm / 0.18 in
DAU003E 125
SD5
Installation and maintenance
The SD5 valve is assembled and tested as per the technical specification of this catalogue.
Before the final installation on your equipment, follow the below recommendations:
-- the valve can be assembled in any position, in order to prevent body deformation and spool sticking mount the product on a flat
surface;
-- in order to prevent the possibility of water entering the lever box and spool control kit, do not use high pressure wash down directly
on the valve;
-- prior to painting, ensure plastic port plugs are tightly in place.
A2
A1 B2 A1
B1 B1
T P
C
SD5 directional valve SDM105 directional valve

with carry--over configuration
Fitting tightening torque - Nm / lbft

THREADS TYPE P and C ports A and B ports T port
BSP (ISO 228/1) G 3/8 G 3/8 G 3/8 (G 1/2*)
With O--Ring seal 35 / 25.8 35 / 25.8 35 / 25.8(50 / 36.9*)
With copper washer 40 / 29.5 40 / 29.5 40 / 29.5 (50 / 36.9*)
With steel and rubber washer 30 / 22.1 30 / 22.1 30 / 22.1 (50 / 36.9*)
UN--UNF (ISO 11926--1) 3/4--16 UNF--2B (SAE 8) 9/16--18 UNF--2B (SAE 6) 3/4--16 UNF--2B (SAE 8)
With O--Ring seal 40 / 29.5 30 / 22.1 30 / 22.1
METRIC (ISO 262) M18 x 1.5 M18 x 1.5 M18 x 1.5 (M22x1.5*)
With O--Ring seal 35 / 25.8 35 / 25.8 35 / 25.8 (50*)
With copper washer 40 / 29.5 40 / 29.5 40 / 29.5 (50*)
With steel and rubber washer 40 / 29.5 40 / 29.5 40 / 29.5 (50*)
(*) -- Only for series circuit.
circuit
NOTE -- These torque are recommended. Assembly tightening torque depends on many factors, including lubrication, coating and
surface finish. The manufacturer shall be consulted.
126 DAU003E
SD5
SD5 directional control valve
O--Ring seal 15.88x2.62 -- code: 4GUA115926

Note
In case of assistance follw this assembling procedure
- fit the O--Rimg seal in seat on lever side;
- fit the spool from the opposite side and till it is possible to
fit the other O--Ring seal;
- position the spool in centre.
Positioner kit
Load check valve
Body
Sealing edge
Lever
pivot box
Spool
Main relief valve Normally spools are interchange-
able. Verify the smoothness dur-
ing the assembly
NOTE -- All articulated parts inside cap, lever box and mechanical joystick are lubricated with synthetic base grease grade NLGI2
Malfunction Cause Remedy

External leakage pivot box lever or Worn spool seal due to mechanical Locate the leakage and replace the seal.
control kit side. actuation or high back pressure. Check back pressure level.
Excessive internal leakage on A and B Increase clearance between spools and Replace the directional control valve and
ports. body due to high wear. check the oil contamination level.
Dropping load during transition while Remove the load check valve and clean
High leakage on the load check valve.
raising the seat, verifing it’s not dented.
Inability to build pressure on A and B Pressure relief valve blocked open. Remove and clean or replace the valve.
ports. Low pump pressure and flow. Check the pump and circuit.
DAU003E 127
SD5
SDM105 directional control valve
O--Ring seal 15.88x2.62 -- code: 4GUA115926

Note
In case of assistance follw this assembling procedure
- fit the O--Rimg seal in seat on lever side;
- fit the spool from the opposite side and till it is possible to
fit the other O--Ring seal;
- position the spool in centre.
Positioner kit
Main relief valve
Body
Compensator spool
Lever pivot box
Spool
Normally spools are interchange-
able. Verify the smoothness dur- Flow control with wheel regulation
ing the assembly
NOTE -- All articulated parts inside cap, lever box and mechanical joystick are lubricated with synthetic base grease grade NLGI2
Malfunction Cause Remedy

External leakage pivot box lever or Worn spool seal due to mechanical Locate the leakage and replace the seal.
control kit side. actuation or high back pressure. Check back pressure level.
Excessive internal leakage on A and B Increase clearance between spools and Replace the directional control valve and
ports. body due to high wear. check the oil contamination level.
Pressure relief valve blocked open. Remove and clean or replace the valve.
Low pump pressure and flow. Check the pump and circuit.
Inability to build pressure on A and B
ports. Substitute the compensator spool and
Compensator spool is jammed. verify the smoothness during assembly.
Check the oil contamination level.
The flow doesn’t vary at the working Control device of flow regulator is
Substitute the flow regulator.
ports by operating the flow regulator. damaged.
128 DAU003E
SD5
Accessories
Connectors
Type C01 code: 2X1001020 Type C02 code: 2X1001010 Type C03 code: 2X1001030
2P+T, according to DIN43650. 2P+T according to ISO4400 / DIN43650--A 3P+T according to ISO4400 / DIN43650--A
31.5 23.5 33 30 28.5 28
1.24 0.93 1.30 1.18 1.12 1.10
0.55
14
31.5
1.24
2 1 1
40.5
1.59
42.5
1.67
1.97
50
PG09 PG09 PG09
Type C05 code: 2X1001080 Type C07 code: 5CON001 Type C08 code: 5CON003
3P+T according to ISO4400 / DIN43650--A. 2 poles, type Packard “Weather Pack” 2 poles, type AMP “Junior--Power--Timer”
With bridge rectifier, to use with VAC supply. male housing with female ends female housing with female ends
38.8 23 17.5
53 0.91 0.69
2.09 1.53
0.63
16
40.5
1.59
21.2
0.83
37.5
1.48
54.2
2.13
2.79
21.3
71
17 11.8
30 0.85 0.67 0.46
1.18
PG09
Type C11 code: 5CON006 Type C17 code: 5CON005 Type C19 code: 5CON007
4 poles according to VDE0660--0110 2 poles, type Packard “Weather Pack” 2 poles, type “Deutsch DT06--2S”
female housing with male ends male housing with female ends
23 16
0.91 0.63
28.4
1.12
1.85
1.46
47
37
0
0.59
∅ 13 PG07
15
∅ 0.51 24
0.95
DAU003E 129
SD5
Accessories
Connectors
Type C20 code: 5CON017 Type C21 code: 5CON018 Type C24 code: 5CON0031
2 pole, type “PACKARD Metri--Pack” 2 poles, type “AMP Fastin--Faston” 2 poles, type “AMP Superseal”
male housing with female ends female housing with male ends male housing with female ends
10 15.2
0.39 0.60
1.26
27.5
1.08
32
22.9
0.90
23 17.3
0.91 0.68
Nominal Permitted conductor Permitted cable Weather

Type Poles Nominal voltage
current section range diameter range protection
C01 2P + T 250 VAC / 300 VDC 10 A max.1.5 mm2 / max.0.0023 in2 6 to 8 mm / 0.24 to 0.31 in IP65
C05 3P + T 230 VAC 1.5 A max.1.5 mm2 / max.0.0023 in2 6 to 8 mm / 0.24 to 0.31 in IP65
C06 3P + T 250 VAC / 300 VDC 6A max.0.75 mm2 / max.0.00116 in2 3.5 to 6 mm / 0.14 to 0.24 in IP65
C07 2P / 20 A 1 to 2 mm2 / 0.00155 to 0.0031 in2 2.8 to 3.5 mm / 0.11 to 0.14 in IP67
C08 2P 250 VAC 12 A 0.5 to 1 mm2 / 0.00077 to 0.00155 in2 1.3 to 1.6 mm / 0.05 to 0.063 in IP65
C11 4P 50 VAC / 120 VDC 6A 0.14 to 0.5 mm2 / 0.00022 to 0.00077 in2 4 to 7.5 mm / 0.16 to 0.29 in IP65
C17 2P / 20 A 1 to 2 mm2 / 0.00155 to 0.0031 in2 1.3 to 1.4 mm / 0.05 to 0.067 in IP67
C19 2P / 13 A 1 to 1.2 mm2 / 0.00155 to 0.00186 in2 2.2 to 3.5 mm / 0.088 to 0.14 in IP67
C20 2P / 14 A 0.8 to 1 mm2 / 0.00124 to 0.00155 in2 1.3 to 1.7 mm / 0.05 to 0.067 in /
C21 2P / 7A 0.3 to 0.8 mm2 / 0.00046 to 0.0012 in2 2.2 to 3 mm / 0.087 to 0.118 in /
C24 2P / 14 A 0.3 to 5 mm2 / 0.00046 to 0.00077 in2 1.4 to 1.7 mm / 0.055 to 0.067 in IP67
Notes
SD5 valve can be supplied with one coat of black paint (CVN configuration).
Description example: SD5/2--P(JG3--120)/18L/18L/AET--<CVN>
NOTE -- For different colour consult Sales Department.
130 DAU003E
SD5
DAU003E 131
WALVOIL S.P.A.
42100 REGGIO EMILIA • ITALY • VIA ADIGE, 13/D
TEL. +39.0522.932411 • FAX +39.0522.300984
E--MAIL: INFO@WALVOIL.COM • HTTP: //WWW.WALVOIL.COM
SERVIZIO COMMERCIALE
TEL. +39.0522.932555 • FAX +39.0522.932455
D1409808I
DAU003E

TESTO ITC KORINNA 28mm Allargato: Monoblock Directional Control Valve

Uploaded by

Copyright:

Available Formats

TESTO ITC KORINNA 28mm Allargato: Monoblock Directional Control Valve

Uploaded by

Document Information

Original Title

Copyright

Available Formats

Share this document

Share or Embed Document

Sharing Options

Did you find this document useful?

Is this content inappropriate?

Copyright:

Available Formats

TESTO ITC KORINNA 28mm Allargato: Monoblock Directional Control Valve

Uploaded by

Copyright:

Available Formats

TESTO ITC KORINNA 28mm Allargato

Nominal flow rating 45 l/min

CAVITY ISO 1179 11926 9974--1

Inlet to work port

Work port to outlet

NOTE -- Measured with spool type 1.

Directional valve with parallel circuit

Dimensional data (parallel circuit)

WALVOIL Valve type

SD5/4--P 211.5 8.33 184 7.24 8.1 17.9

A Pressure line Tank line

Standard configuration Configuration with upper inlet and outlet

Description example Description example:

Description example: Valve setting (bar)

SD5 / 2 -- P (JG3-- 120) / 1 8 L / 1 8IM . P3(G3-- 100) / AET *

1. Body kits * 3. Spool options page 13

NOTE (*) -- Codes are referred to BSP threads.

4. “A” side spool positioners page 20 4. “A” side spool positioners

Inlet relief options

Direct pressure relief vave

Adjustable spring type (2, 3, 4).

G: with screw H: valve set and locked

max. 51.5 59.5

400 (psi) 400 (psi) 400 (psi)

200 3000 200 3000 200 3000

100 1500 100 1500 100 1500

SV: relief valve blanking plug

Spool metering P→A(B) Spool metering A(B)→T

P--B--T closed, flow through line (LC) open

Spool metering P→A Spool metering A→T

A--B → T (float in lock position)

P--A--B--T closed flow through line (LC) open

P--A--B--T closed flow through line (LC) open

”A” side spool positioners

With spring return in neutral position

With spring return in neutral position

Allen wrench 5 Allen wrench 4 1 0 2

9.8 Nm / 7.2 lbft 0 0

”A” side spool positioners

Allen wrench 4 Allen wrench 4

Operating features Operating features

Allen wrench 4 200 40

Detent area Detent area

“A” side spool positioners

Solenoid lock device type 8K

Coil with ISO4400 connector

NOTE -- The kit control must be turned at 180°. when pilot

Nom. voltage tolerance . . . . . . . . : ±10%

Nom. voltage tolerance . . . . . . . . : ±10%

Solenoid lock device type 8K

3 positions “A” side spool

“A” side spool positioners

Electromagnetic detent type 8RM2

Solenoid kit with connector

Notch -- 6.6 Nm / 4.9 lbft Connector wiring

8MHE3(NC) kit 8MHE3(NO) kit

Configuration with Configuration with

Mobile contact Mobile contact

Ouput signal with NC circuit Ouput signal with NO circuit