Drum Dryer Heat Transfer Heat Recovery

Drum Dryer Condensate Removal Heat Transfer and
Energy Recovery
Project
Rebuild of a drum dryer syphon, rotary joint, and associated steam and condensate
system used in the food industry for the manufacturing of potato flakes.
Process
The drum dryer is fed with live steam and operates at 8 barG steam pressure. Heat is
transferred from hot, condensing steam inside the drum dryer to the cooler product
passing over the rotating drum. This evaporates moisture from the incoming slurry
and drying the product for onward processing.
Operation and Configuration Before Kadant Rebuild
Steam was fed into the dryer under a two-stage pressure reduction control system.
This took the steam from high-pressure to the 8 barG drum operating pressure. The
steam condensed within the drum dryer and drained from the dryer by two simple
bent-pipe stationary syphons which entered the cylinder at either end of the drum
dryer through dual-flow rotary joints. The condensate from the drum dryer drained
via a steam trap from the dryer to a flash steam vessel and this condensate was then
drained to an atmospheric vessel.
There were several problems with this configuration.
First, draining hot, higher-pressure condensate to a vessel at lower pressure creates

flash steam as the heat energy contained within the condensate effectively boils a
proportion of the condensate and converts it to steam. When the lower pressure vessel
is vented to atmosphere the steam is lost along with all its energy. Also, the design of
the simple bent pipe stationary syphons was not robust. The clearance at the syphon
tip was not always maintained due to the syphons moving within the drum, causing
inconsistent drainage. This movement of the syphon also increases the possibility of
syphon failure if it contacts the internal surface of the dryer. As a result, the syphon
clearances are set quite high, leading to more condensate being inside the drum dryer
and so, reducing the effectiveness of heat transfer to the product. Air evacuation from
the drum dryer was also poor with the system, due to the installation of the steam trap
and its poor air handling capability. The build-up of air within heat transfer
equipment reduces both the effective temperature of the steam and affects the
uniformity of the heat transfer profile across the width of the rotating drum.
Kadant’s Solution
 The two-stage pressure reduction was modernized to a single stage pressure reduction
using a high-quality pressure control valve capable of accurately controlling with high
differential pressures. This modernized the system to reduce future maintenance.
 A new flash recovery system was designed to eliminate the flash steam loss to atmosphere.
The flash steam was recovered to a low-pressure user to reduce the amount of live steam
required in the lower pressure system. This reduced total steam use and boiler make-up
water usage.
 A high-capacity scoop syphon was installed to replace the two bent pipe syphons. This
high-capacity scoop rotates with the dryer drum. The four scoop buckets are installed at 90
degrees to each other, so they continuously evacuate the condensate, draining it from the
drum without the need for differential pressure. This improved drainage of the condensate
and reduced the amount of equipment installed on the drum, further reducing future
maintenance requirements.
 The steam trap was removed and a new drainage system with modern, automatic air
removal control was installed in the condensate system. This automated process ensured
the correct evacuation of air from the drum on start-up, decreasing warm-up times, and
improving heat transfer through the drum.
Energy Recovery Benefits
The energy saving from the above system being implemented was over 2.9 million
kWh / year, worth approximately €86,000 per year in saved energy and a
CO2 reduction of almost 160 ton/year.
PLEASE NOTE:
The energy costs in the above benefits for conditions in the United Kingdom. The
costs in other countries may be different.
October 05, 2021
 Written by:
Rob Parker
Engineering Manager, Kadant Johnson Systems UK
RELATED ARTICLES
Steam Energy Efficiency with High-Pressure Condensate Return

< PrevNext >
Get our monthly blog digest in your inbox
Sign Up
CATEGORIES
 Forming (2)
 Maintenance (38)
 Optimization (95)
 Fluid Handling (207)
 Rotary Joints & Unions (34)
 Auxiliary Steam Equipment (18)
 Steam (17)
 Expansion Joints (25)
 Doctoring, Cleaning, Filtration (216)
 Roll Cleaning (89)
 Water Management (45)
 Fiber Processing (15)
 Technology (8)
 Meet Team Kadant (40)
 Events (30)
© Kadant Inc.
Privacy | Terms | Benefits Compliance

Drum Dryer Heat Transfer Heat Recovery

Uploaded by

Copyright:

Available Formats

Drum Dryer Heat Transfer Heat Recovery

Uploaded by

Document Information

Original Description:

Original Title

Copyright

Available Formats

Share this document

Share or Embed Document

Sharing Options

Did you find this document useful?

Is this content inappropriate?

Copyright:

Available Formats

Drum Dryer Heat Transfer Heat Recovery

Uploaded by

Copyright:

Available Formats

Drum Dryer Condensate Removal Heat Transfer and

Operation and Configuration Before Kadant Rebuild

There were several problems with this configuration.

First, draining hot, higher-pressure condensate to a vessel at lower pressure creates

Energy Recovery Benefits

October 05, 2021

Steam Energy Efficiency with High-Pressure Condensate Return

You might also like