™

Fiber Defender FD322

User Manual

PM-ENG-012 Rev G
Fiber Defender FD322TM User Manual Confidential – Limited Distribution
© Copyright 2014, Fiber SenSys® all rights reserved. No part of this publication may be
reproduced or transmitted in any form or by any means, electronic or mechanical, including
photocopy, recording, or any information storage and retrieval system, without permission in
writing from Fiber SenSys®, Inc., 2925 NW Aloclek Drive, Suite 120, Hillsboro, Oregon 97124,
USA.

This manual is provided by Fiber SenSys Inc. While reasonable efforts have been taken in the
preparation of this material to ensure its accuracy, Fiber SenSys Inc. makes no express or
implied warranties of any kind with regard to the documentation provided herein. Fiber SenSys
Inc. reserves the right to revise this publication and to make changes from time to time in the
content hereof without obligation of Fiber SenSys Inc. to notify any person or organization of
such revision or changes.

FD322TM is a trademark of Fiber SenSys Inc. (FSI)

Fiber SenSys® is a registered trademark of Fiber SenSys Inc.

Windows® is a registered trademark of Microsoft Corporation.

Fiber SenSys Inc.

2925 NW Aloclek Dr.
Suite 120
Hillsboro, OR 97124
USA

Tel: 1-503-692-4430
info@fibersensys.com
www.fibersensys.com

Page 2 Confidential – Limited Distribution

Table of Contents

1. Introduction ......................................................................................................... 4
2. Safety Information ............................................................................................... 6
Safety Terms .................................................................................................. 6
Electrical Safety .............................................................................................. 6
Covers and Panels ......................................................................................... 6
Inspection ....................................................................................................... 7
Laser Radiation............................................................................................... 7
Fiber-Handling Precautions............................................................................. 7
FCC Rules ...................................................................................................... 8
3. The Sensing Fiber ............................................................................................... 9
Fiber Optic Sensing ........................................................................................ 9
Sensor Cable.................................................................................................. 9
Fence Installation .......................................................................................... 10
Connectors ................................................................................................... 10
4. The Alarm Processing Unit (APU) ..................................................................... 12
APU Description ........................................................................................... 12
5. FD322 Tuning Software ..................................................................................... 16
Using FD322 Tuning Software ...................................................................... 16
Calibrating System Loss ............................................................................... 17
APU Parameter Editor Mode......................................................................... 18
Realtime Mode.............................................................................................. 20
6. Integrating the APU into the Security System .................................................... 21
7. Testing and Certification .................................................................................... 22
8. Maintenance ...................................................................................................... 23
• Appendix A. Product Specifications ........................................................................ 25
• Appendix B. FD322 Menu Structure ....................................................................... 26
• Appendix C. Warranty Information.......................................................................... 31
• Appendix D. Referenced Documents ...................................................................... 32

Fiber Defender FD322TM User Manual Page 3

1. Introduction
The Fiber SenSys FD322 is an electro-optical Instrument that uses optical fiber as a distributed
sensor for detecting intruders attempting to cut, climb, or crawl under a fence. The APU can be
calibrated or tuned to disregard non-threatening stimulus such as wind and animals; thus,
reducing nuisance alarms. When an intruder is detected, the APU sends out an alert via IP/XML
Ethernet communication as well as state changes via terminal contacts that can be used to
switch on lights, cameras, sirens, or to signal an alarm panel.

The optical fiber-based system has been designed to be immune to the effects of
Electromagnetic Interference (EMI), lightning, and Radio Frequency Interference (RFI). The
FD322 provides maximum effective intrusion detection through its inherent system flexibility and
advanced programmability.

Because the fiber optic sensors use laser light which is intrinsically inert, the FD322 system can
be installed safely at chemical plants, ammunition depots, or any location where the use of
electricity is a concern.

RS-232 communication allows for simple setup and calibration, while IP/XML communication for
direct network interface allows for easy integration with any security solution.

A key component of the FD322 is its fiber optic sensor cable; this uniquely-designed cable,
which is sensitive to movement, pressure, and vibration, can be routed along the fabric of a
fence to detect climbing and cutting. The detection of an intruder triggers an alarm from the
Alarm Processing Unit (APU).

Some of the intrusion threats the FD322 can be used to detect include:

• Fence climbing (along both the fabric and post)

• Fabric cutting

• Crawling underneath a fence

• Ladder assisted climbing of a fence

A single run of sensor cable can protect a zone up to 500 meters (1,640 feet) in length. The
APU channels can be programmed independently, which gives users the ability to protect two
separate zones from the same APU.

4
Figure 1-1. FD322 fiber optic intrusion detection system.

5
2. Safety Information
This section contains information to help ensure personal safety and proper operation of
equipment. Please read and follow all these instructions carefully and keep them accessible for
future reference. Whenever using the FD322, use only attachments and accessories that have
been specified by FSI and refer all servicing to qualified personnel.

Safety Terms
The following icons may appear throughout this manual:

CAUTION: Identifies conditions or practices that could result in damage to

equipment and/or loss/contamination of data.

WARNING: Identifies conditions or practices that could result in non-fatal personal

injury.

DANGER: Identifies conditions or practices that could result in serious injury or

death.

Electrical Safety
If the FD322 is damaged or malfunctions, disconnect power to the APU. Do not use the APU if
any of the following conditions exist:

• The APU is visibly damaged.

• The APU does not operate as expected.

• The APU has been subjected to prolonged storage under adverse conditions.

• The APU has been damaged during shipment.

Do not put the APU into service until qualified service personnel have verified its safety.

Covers and Panels

There are no user-serviceable parts inside the APU. To avoid personal injury, do not remove
any of the APU’s covers or panels. The product warranty is void if the factory seal is broken. Do
not operate the product unless the covers and panels are installed.

6
Inspection
The FD322 APU should be inspected for shipping damage. If any damage is found, notify Fiber
SenSys and file a claim with the carrier. Save the shipping container for possible inspection by
the carrier.

Laser Radiation
The FD322 APU is a Class I laser product, as defined by IEC 60825-1 and CFR 21 subchapter
J. A Class I laser product emits insufficient laser radiation to constitute a hazard. However,
avoid direct eye exposure to the output of this product or to the open end of any optical-fiber
cable connected to this product.

The following stamp is found on the front panel of the FD322 APU:

Figure 2-1. Class 1 laser stamp on front panel of the FD322 APU

Fiber-Handling Precautions
Optical fibers are made of glass and the ends of a broken fiber can be sharp and may
become lodged in the skin. Take appropriate glass-handling precautions.

7
FCC Rules
Note: This equipment has been tested and found to comply with the limits for a Class B
digital device, pursuant to Part 15 of the FCC Rules. These limits are designed to provide
reasonable protection against harmful interference in a residential installation. This
equipment generates, uses, and can radiate radio frequency energy. If the equipment is
not installed and used in accordance with the instructions it may cause harmful interference
to radio communications. However, there is no guarantee that interference will not occur in
a particular installation. If this equipment does cause harmful interference to radio or
television reception, which can be determined by turning the equipment off and on, the user
is encouraged to try to correct the interference by one or more of the following measures:

• Reorient or relocate the receiving antenna.

• Increase the separation between the equipment and receiver.

• Connect the equipment into a different outlet than the receiver.

• Consult the dealer or an experienced radio/TV technician for help.

8
3. The Sensing Fiber
The FD322 detects trespassers by sensing disturbances caused by an intruder attempting to
gain access by climbing or cutting a chain-link style fence. The sensing cable must be routed
along the fabric of a fence to detect climbing and cutting.

Fiber Optic Sensing

When an optical fiber is exposed to vibration, the disturbance causes small asymmetric changes
in the fiber’s density. In turn, these changes in density cause measurable changes in certain
characteristics of laser radiation that is transmitted through the fiber. The FD322 uses precision
lasers and detectors, along with sophisticated digital signal processing, to measure changes in
the laser radiation. The processor analyzes the incoming signals in order to determine whether
they are caused by intruders, or harmless nuisances, such as vibrating equipment. To learn
more about fiber optics and their use as sensors, refer to the application note on fiber optics
titled: AN-SM-007 Fiber Optics.

Sensor Cable
There are two types of sensor cable for the FD322: SC-3 and SC-4.

SC-3 is distinguished by its dark brown protective jacket. This jacket ensures the cable is
resistant to weather, dirt, etc. although the cable is not outdoor rated and should be contained
within protective conduit.

• SC-3 (brown jacket) – 3 mm sensor cable used for perimeter applications.

Sensor cable comes in varying lengths, with up to 2000 meters (6500 feet) per spool.

• SC3-C (cable in conduit) – 3 mm sensor cable within grey ½” UV rated conduit.

Cable in conduit should be purchased in premeasured zone lengths and reels can be up to 800
meters.

SC-4 comes in a thicker green jacket and is outdoor rated. This cable can be attached to the
fence directly using nylon cable ties and does not need to be deployed within protective
conduit.

• SC-4 (green jacket) - 4 mm sensor cable used for perimeter applications.

Sensor cable comes in varying lengths with up to 2000 meters (6500 feet) per spool.

9
Fence Installation
As mentioned previously, the purpose of a fence line sensor cable installation is to detect
threats against a fence line boundary such as climbing or fabric cutting. Under most
circumstances, the sensor cable is deployed in a "loopback" configuration with strands of the
loop running along the top and bottom halves of the fence height. In high security cases, the
cable is also run along barbed wire outriggers and fence posts for increased perimeter
protection.

Ultimately, the method by which the FD322 system is deployed is up to the end user; Fiber
SenSys does not recommend or mandate one particular installation setup over another;
however, the general procedure for installing the FD322 system is:

1. Assess: Survey the site to be protected and record all information needed for the
site design phase.

2. Design: Create a strategy for protecting the site. This includes planning the level
of security, choosing the location of the APUs, provision of electrical power, and
planning cable routing.

3. Install: Proper deployment of the fiber optic sensor and correct installation of the
Fiber SenSys system.

For ease of installation, the FD322 can be purchased in an all-inclusive kit. The FD322-Rapid
Fiber™ Kit can be ordered for 100 m zones or 200 m zones. The kit contains the APU and a
universal input power supply pre-installed in an easily mountable weatherproof NEMA 4X IP66
rated enclosure. The kit comes with two pre-connectorized spools of SC-4 fiber, one for each
zone, and UV-rated nylon cable ties for quick and easy installation. For more detailed
installation instructions for the FD322-Rapid Fiber™ Kit refer to the application note: AN-ENG-
026 FD322-Rapid Fiber Kit Installation.

To learn more about site assessment, site design or sensing fiber installations, refer to the
application note on installation: AN-ENG-027 Site Design and Installation for FD300 Series.

Note: Once the fiber has been installed the APU must be calibrated for the loss of the
sensing fiber installation. See Calibrating System Loss in section 5.

Connectors
FD322 is a fiber optic intrusion detection system that can monitor up to two fully independent
zones (sensing fibers) using a single APU. To maintain a high signal-to-noise ratio, it is
important that all connections within a given fiber-optic sensor (zone) be made by either fusion
splicing or by physical-contact fiber-optic connectors (PC). It is helpful to test the optical loss of
each zone. The sensing fibers plug directly into the APU and are always connected with an ST
connector (ST/PC).

10
 Note: It is important that only clean optical connectors are inserted into the APU’s optical
inputs and outputs; dirty connectors can degrade the performance of the APU or even
cause irreversible damage. When leaving connectors unconnected make sure they have
protective caps installed on the ferrules. Caps protect the ferrule from damage that might be
caused by bumping the ferrule against a foreign object. However, when caps are dirty they
don’t protect (effectively) against microscopic contamination. Consequently, be sure to
clean all connectors prior to insertion whether or not they have been capped. For more
information on the care and cleaning of fiber-optic connectors, refer to the application note
on fiber optics: AN-SM-007 Fiber Optics.

11
4. The Alarm Processing Unit (APU)

APU Description
The FD322 APU has 7 input/output ports. There are 2 optical connectors (labeled "Input" and
"Output") for each channel. In addition, the APU has a terminal connector strip for DC power
and relay leads, an RS-232 connector, and an Ethernet connector. Figure 4-1 shows the layout
of the ports for a Model FD322 APU.

Ethernet Connector

RS-232 Connector
Power, Tamper,
and Relay
Connectors

Channel B Channel A
Optical Output Optical Output

Channel B Channel A
Optical Input Optical Input

Figure 4-1. The FD322 APU Connectors

At the right-hand side of the APU module is a 12-pin terminal strip for connecting electrical
power, alarm, fault, and tamper relays. Each pin is labeled. The terminal pins, from bottom to
top of the terminal strip, are listed in Table 4-1.

12
 Pin Description
1 +12 to +24 VDC
2 Ground
3 Tamper Input
4 Tamper Input
5 Fault
6 Fault
7 Channel A Normally Closed
8 Channel A Common
9 Channel A Normally Open
10 Channel B Normally Closed
11 Channel B Common
12 Channel B Normally Open
Table 4-1. Terminal Pin Descriptions

Power. Pins 1 and 2. 12 to 24 VDC is connected to these terminal pins. The positive lead is
the bottom-most pin (Pin 1) and ground is the pin immediately above it (Pin 2).

Tamper. Pins 3 and 4. The leads of a tamper switch are normally connected here. Whenever
the tamper circuit opens (because the tamper switch is not set or the enclosure door opens,
etc.), the alarm relay activates and remains activated until the circuit closes again or the tamper
feature is disabled (this feature is disabled by default).

Fault. Pins 5 and 6. These pins are used to connect the fault relay to a remote indicator.
The normally-closed fault relay contacts open if there is a loss of optical power or if power
drops below the nominal threshold on either channel.

While fault indication is displayed on the APU front panel for each individually affected channel,
only one set of fault relay contacts is provided and is shared by both channels.

Channel A Alarm (normally-closed contact). Pins 7 and 8. When the APU

determines an alarm condition in the channel is met, the contact opens. In an unpowered
state, this contact is open.

Channel A Alarm (normally-open contact). Pins 8 and 9. When the APU determines
an alarm condition in the channel is met, the contact closes. In an unpowered state, this
contact is closed.

13
Channel B Alarm (normally-closed contact). Pins 10 and 11. When the APU
determines an alarm condition in the channel is met, the contact opens. In an unpowered
state, this contact is open.

Channel B Alarm (normally-open contact). Pins 11 and 12. When the APU
determines an alarm condition in the channel is met, the contact closes. In an unpowered
state, this contact is closed.

WARNING!
DO NOT APPLY AC VOLTAGE TO THESE PINS. THE ALARM RELAY CONTACTS ARE RATED
FOR DC VOLTAGE ONLY (100mA at 24 VDC).

LED indicators. LED indicators for each channel are found on the front panel of the module.

• "Fault" indicates a loss or significant degradation of returning optical power.

• "Event" indicates a disturbance or event has been detected in the sensor cable.

• "Alarm" indicates an alarm condition has occurred.

• "Power'' indicates the module is plugged in and receiving power.

Pressing the Test button (located below the LED indicators) causes the ALARM and FAULT
LEDs to light up and the corresponding relay contacts to change state.

On the upper left-hand side of the APU there is an RJ45-style connector for TCP/IP Ethernet
communication with a security head-end or other annunciator/monitoring equipment.

The front panel of the APU has an RS-232 connector for connecting to a PC during calibration.
The pin-out for the RS-232 connector is shown in figure 4-2 and table 4-2.

Figure 4-2. Pin-out for the RS-232 connector

14
 Table 4-2. RS-232 Pin Assignments
Pin Description
Number

1 No connection

2 T x D transmit

3 R x D receive

4 No connection

5 Ground

6 No connection

7 RTS

8 CTS

9 No connection

Note:
Connections to the APU’s RS-232 interface should use straight-pin DB-9
serial cable

15
5. FD322 Tuning Software
Terminal emulation software, or FD322 Tuning Software, is required to adjust the tuning
parameters of the APU. They run on a PC that is connected to the APU via the RS-232 port on
the front of the APU. Any terminal emulation software will work to change APU parameters, but
FD322 Tuning Software is recommended for precision tuning.

FD322 Tuning Software is a Windows-based software module that allows for the tuning of the
system so that it has maximum sensitivity when detecting intrusions with maximum rejection for
nuisance alarms. FD322 Tuning Software also allows the user to monitor system performance
and record and analyze sensor data.

For instructions on how to change settings using a terminal, refer to Appendix B at the end of
this manual.

Using FD322 Tuning Software

With power off to the APU, connect one end of an RS-232 cable to the APU and the other end
to the PC from which the FD322 Tuning Software will be launched, then turn on power to the
APU.

Launch the FD322 Tuning Software by clicking on the icon pictured below or navigate to “All
Programs | Fiber SenSys | FD322 Tuning Software”:

Figure 5-1: FD322 Tuning Software Icon

Upon launching the program, click the tab in the top left labeled “Serial Port” and click on the
appropriate port from the list of available ports. Then click “Connect to COM Port.”

16
 Figure 5-2. The Serial Port pop-up window

Calibrating System Loss

System loss is a measure of the optical loss in the fiber-optic sensor, including the loss due to
bad connectors, breaks or tight bends. The system automatically adjusts its gain every time the
loss is measured, up to a loss of 6 dB. If the system loss exceeds 6 dB, make any repairs
necessary to reduce the loss to below that threshold.

Note: All commands in the terminal must be written in all capital letters.

To measure loss, select Terminal mode and then type CALIB. Type ML and when prompted,
type Y. This places the APU in the loss calibration mode and the following prompt appears:

Cha Loss(dB)= xxx@ mm/dd/yy hh:mm

This prompt lists the optical loss along with the date and time it was measured. To measure the
current loss, simply shake the channel’s sensing cable vigorously for about ten seconds and
then (within about two seconds after shaking the fiber) press the test button on the front of the
APU for channel A.

After pressing the test button, the status line changes to read:

Cha Loss(dB)= xxx SAVED @ mm/dd/yy hh:mm

The word SAVED indicates that the system has been successfully calibrated and the new loss
setting (xxx) is displayed along with the current date/time.

17
Repeat this procedure two or three times ensuring that the loss measurement is less than 6 dB
and does not change by more than ±1 dB. Once the system loss has been calibrated for
channel A the same procedure is used to calibrate channel B.

If the loss consistently measures higher than 6 dB, a test cable that is known to be good can be
used to determine if the excess loss is caused by a damaged APU or a damaged sensing cable.
To do this, connect the test cable directly between the Input and Output ports on the APU and
then follow the process just described (using Terminal mode and CALIB) for measuring loss. If
the loss is still high then the APU may be damaged. If loss is determined to be coming from the
APU, contact Fiber SenSys Tech Support.

APU Parameter Editor Mode

From the tab on the left labeled “Modes” select “Parameter Editor.” The parameter editor mode
(see figure below) is where the parameters are read, defined, and written to the APU.

Figure 5-3. The FD322 Tuning Software Parameter Editor screen

Press the Receive button (upper right-hand corner of the screen) to read the current tuning
parameters from the APU. FD322 Tuning Software queries the APU, reads in the processor
information, and displays it:

18
 Figure 5-4. Users can change APU Parameter Settings using the Parameter Settings Table

Once received by FD322 Tuning Software, the APU model number, serial number,
manufacturing date, and firmware version appear at the top of the Parameter Settings table.
Also appearing in the table are the individual calibration parameters and their current settings.
The allowable range for each parameter as well as the default value is also shown. Parameters
appearing in light red cells of the table are default values and cannot be edited.

To edit or change a parameter setting:

1. Click on the desired parameter (only parameters appearing in white table cells can be
edited). The parameter’s row is highlighted in yellow indicating it is ready for editing.

2. Change the parameter setting to the desired value. Numerical values can be entered
using the number keys or the value can be incremented/decremented from the current
value using the + or – keys. Numerical values must also be kept within the allowable
range or the software will reject the new value and prompt the user to enter a value
within range.

3. Once the parameters have been edited, the new settings can be saved to the APU by
pressing the Send button.

19
For detailed information about these tuning parameters, refer to the Fiber SenSys application
note on tuning parameters titled: AN-SM-008 Setting the Tuning Parameters.

Realtime Mode
As a tuning aid, FD322 Tuning Software provides a powerful tool to help visualize the live
frequency content of different sensor signals called Real Time (see figure 5-5). To use this
function, from the tab on the left labeled “Modes” select “Real Time.”

Figure 5-5. Signal with low frequency content (top) caused by wind, and a signal with high-frequency content (bottom) caused
by cutting the fence fabric.

20
6. Integrating the APU into the Security System
The FD322 APU is designed to be installed into a local-area network (LAN) and connected to a
security head-end or other annunciator/monitoring equipment.

The FD322 communicates via XML (extensible markup language) sending status messages to
the network such as alarm, tamper, and fault conditions. It can also receive device-
configuration commands in XML format.

Processes involved in integrating the APU into a security system are described in detail in the
networking application note, AN-SM-009 APU Networking:

21
7. Testing and Certification
System tuning is necessary when installing new systems, replacing APUs, or after performing
any system maintenance that involves changes to the cable assembly. Anytime the system is
tuned, it should be re-tested to verify that it meets all requirements for probability of detection
(PD) and rejection of nuisance alarms. Basic tests include:

Tamper test

If the tamper input on the FD322 APU is used, the connection should be tested by going to the
tamper-protected enclosure, opening it, and verifying that the head end records a tamper alarm.

Fault test

The fault test verifies that a loss of optical power to a zone results in a cable fault indication for
that zone on the APU. To conduct this test, disconnect the optical fiber for zone 1 and verify
that the fault LED for zone 1 is illuminated (this LED is located on the front of the APU).
Reconnect the fiber from zone 1 and verify that the fault LED light goes off. Repeat this process
for the other zone.

Probability of detection (PD)

PD performance testing involves reviewing the sorts of threats that need to be detected,
simulating those threats, and measuring the probability with which the system detects the
expected method of intrusion. To obtain statistically significant samples, perform each threat
simulation a minimum of 20 times at various locations in each zone.

For example, to determine the PD for an intruder attempting to climb the fence, have a volunteer
climb nearly to the top of the fence, preferably bringing his or her beltline level with the top of the
fence fabric, and then dismount in a controlled and steady manner. Perform the simulated
intrusion at least 20 times while keeping track of the number of times the system triggers an
alarm (count only one alarm per simulated intrusion).

Verify that the system triggers an alarm, as intended, with the required probability of detection.
If the PD is too low, tune the system to be more sensitive. Repeat this procedure for each
installed zone on the secured perimeter.

22
8. Maintenance
Maintenance consists of routine inspections and periodic testing to verify the performance of the
tamper and fault alarms, as well as the probability of detection for simulated intrusions.

Visually inspect the FD322 APU at least every 90 days:

1. Ensure the Power LED is illuminated and all alarm and fault LED indicators are normal.

2. Check the optical connectors at the sides of the APU, making sure they are not pinched
or otherwise compromised.

On a periodic basis (once every 180 days at a minimum), perform the tests described in section
7:

• Tamper (if used).

• Fault.

• Probability of detection.

• Relay function (if used).

There are no user-serviceable parts in the FD322 APU. In case of an APU failure, corrective
maintenance involves replacing the APU. If you replace the APU, you must perform a complete
system configuration and recalibration.

To replace the APU, follow these steps:

1. Ensure all current APU calibration parameters, as well as the system configuration
data, have been saved to a PC file using the FD322 Tuning Software.

2. Disconnect power to the APU and disconnect the optical fibers. Disconnect the
Ethernet connection from the TCP/IP port.

3. Remove the APU and replace it with a new unit.

4. Clean all the optical connectors per the procedures described in the fiber optics
application note: AN-SM-007 Fiber Optics.

5. Connect power to the new APU and repeat the processes described in the chapters
in this manual, on calibration, tuning, integration, and testing.

For troubleshooting assistance, contact Fiber SenSys Technical Support Service: telephone, 1-
503-726-4455; email, support@fibersensys.com; or go to the Fiber SenSys website,
www.fibersensys.com.

23
24
Appendix A. Product Specifications

System Type Alarm processor for perimeter security

Two fully independent zones

Number of Zones
• Sensing fiber length: ≤ 500 meters (1640 feet)
• Minimum bend radius: 5 cm (2 in)
• Uniform sensitivity over the entire length
Multimode Sensing
Fiber • Passive, inert, intrinsically safe
• Immune to EMI and corrosion
• Maximum pull tensile Strength: 27kg (60 lb)

• 12-24 VDC input

APU Power
Requirements • 3 watts @ 12 VDC, 25˚ C

• Serial port for tuning

Communications
• TCP/IP port for alarm output and XML communication

• Individual dry contact alarm relays for each zone –

normally open or normally closed (NO / NC)
• Dry contact alarm relay for fault – Normally Closed (NC)
Fault and Alarm
• 28 to 14 AWG
Relays
• 100 mA, 24 VDC non-inductive
• Dry Contact Resistance 11 Ω typical, 17 Ω max

LED indicators for fault, and alarm conditions for each zone
Front-Panel Display
Temperature: -40˚ C to 70˚ C (-40˚ F to 158˚ F)
Environmental Humidity: 0 to 95% non-condensing

Height = 4.5 cm (1.77 inch)

Width = 42.5 cm (16.75 inch)
Dimensions
Depth = 40.6 cm (16 inch)

• RoHS
Standards and • CE
Certifications • FCC Part 15 Class B

25
Appendix B. FD322 Menu Structure
This appendix provides details for all programmable FD322 system tuning parameters. Each
channel on the FD322 is tuned independent of the other. Therefore, most parameters
discussed in this appendix are duplicated in both channels.

Connect the PC to the APU via serial cable. Launch the terminal emulation software or FD322
Tuning Software, and establish communication between the two instruments. The following
properties must be set to communicate using terminal emulation software:

Bits per Second: 9600

Data bits: 8
Parity: None
Stop bits: 1
Flow control: Hardware

Upon establishing communication with the APU through FD322 Tuning Software in
“terminal” mode or any other terminal emulation software, the system differentiates which
channel is selected at the password prompt:

"CHa Unit is LOCKED, Enter Password"

--or--

"CHb Unit is LOCKED, Enter Password"

At the password prompt, type either "CHA" for Channel A or "CHB" for Channel B to switch from
one channel to another.

In each channel, there are 7 "passwords" that provide the user with access to related APU
parameters or submenus. For instance, the "ADMIN" password provides users with access to
the admin parameters. After entering the password, "ADMIN," users can make adjustments to
the settings as desired. The 7 parameter passwords are:

• STATUS
• HIST
• VERSION
• SETUP
• CALIB
• ADMIN
• CHA/CHB

Each password, and its associated parameters, is explained in detail in the following pages.
Factory default settings were chosen based upon the performance of an FD322 used in tandem
with a seven foot chain link fence having a three-strand barbed wire outrigger.

26
 NOTE: Press the Enter key at any time to exit from any menu, submenu, or
parameter in the terminal.

STATUS
This is a read-only command that provides a real-time diagnostic of conditions such as system
loss, laser current, power supply voltage (to the APU) and any present fault, event or alarm
conditions. When this menu is chosen, for example, the display reads:

Cha Pin(uW)= 723 Las(mA)=35.1

Loss(dB)= 1 Pwr(V)=12.4
[Evnt1][Evnt2][Alarm][Fault]

“Evnt1” and “Evnt2” refer to event conditions at Processor 1 and Processor 2, respectively.

HIST
This is a read-only menu that provides a history of alarms beginning with the most recent.
Alarms are read off according to how long ago they occurred. In addition, each alarm entry is
date/time stamped. For instance, if the alarm history is read after three alarms occurred, the first
report in the alarm history might read:

#3 Alarm, Processor 2 (W=0)

16:41 11/04/06

One can note from this example that the alarm history is provided for each alarm that occurs for
each processor. From this report, the #3 indicates the alarm report number, Processor 2
indicates the processor in which the alarm occurred, and the date and time on the bottom line of
the text indicates when the alarm was received. The “W=” parameter indicates the estimated
wind speed at which the alarm occurred (determined by the internal wind rejection algorithms).

Up to 128 of the most recent alarm events will be stored in volatile APU memory. Each alarm
event exceeding the allowable 128 will overwrite the oldest entry. If at any point you wish to exit
this menu, type “Q” and hit the [Enter] key.

VERSION

This read-only menu gives the APU model number, serial number, firmware version, date of
manufacture, and the number of days the unit has been in operation.

SETUP
This menu allows access to the channel’s settable tuning parameters. They are listed and
described in detail in the below table.

27
NOTE: Hitting ENTER will cycle forward to the next parameter. Typing “-“ and hitting ENTER will
cycle back to the previous parameter.

Parameter Range Default Description

Climb 0 to 50, 20 E Enables or disables the processor and sets the

Sensitivity overall sensitivity of the climb processor.
E or D Although raising the sensitivity level increases
the likelihood of detecting an intruder, it also
makes it more likely that something such as wind
or animals might generate a nuisance alarm.

Cut 0 to 50, 20 E Enables or disables the processor and sets the

Sensitivity overall sensitivity of the cut processor. Although
E or D raising the sensitivity level increases the
likelihood of detecting an intruder, it also makes
it more likely that something such as wind or
animals might generate a nuisance alarm.

Climb Event 1 to 10 3 The number of times that an event must be

Count registered by the climb processor for an alarm
condition to occur.

Cut Event 1 to 10 5 The number of times that an event must be

Count registered by the cut processor for an alarm
condition to occur.

Wind 20 to 80, 50 E Sets how much the APU will dampen the signal
Rejection received from the sensor cable during windy
E or D conditions. A higher wind rejection factor means
more dampening, requiring a signal higher in
magnitude to create an alarm condition.

Climb 10 to 600 200 The lowest allowable frequency used by the

Lowest (Hz) climb processor to evaluate the presence of an
Frequency intruder. This may be set to eliminate lower
order frequencies caused by nuisances such as
vibrations from nearby generators.

Cut Lowest 10 to 600 300 The lowest allowable frequency used by the cut
Frequency (Hz) processor to evaluate the presence of an
intruder. This may be set to eliminate lower
order frequencies caused by nuisances such as
vibrations from nearby generators.

28
CALIB

Access this menu using the "CALIB" password. There are 2 submenus available.

• Time/Date [D]

• Measure Loss [ML]

These submenus are accessed by entering their corresponding submenu entries ("D" for the
Time/Date submenu, "ML" for the Measure Loss submenu).

Time/Date [D]

From this submenu, users can change the time and date setting of the APU's real-time clock.

NOTE: There is only one real-time clock in the APU. Changing this setting affects both
channels.

To change the real-time clock, enter the new time in 24 hour HH:MM format. The date is
entered in MM/DD/YY format.

Measure Loss [ML]

From this submenu, users can measure the loss of their system. The system automatically
adjusts its gain every time you measure the loss. For Instructions on measuring loss, see
Calibrating System Loss in chapter 5 of this manual.

ADMIN
This menu allows access to the channel’s admin settings. They are listed and described in detail
in the below table.

NOTE: Hitting ENTER will cycle forward to the next parameter. Typing “-“ and hitting
ENTER will cycle back to the previous parameter.

Parameter Range Default Description

Enables or disables the tamper monitoring
Enable Y/N N function. When enabled, the normally-
Tamper
closed condition of the tamper circuit is
Switch
observed by the APU. If the circuit is
opened or not connected to the tamper

29
 switch in the enclosure, the tamper alarm
will activate and remain activated until the
tamper circuit is closed or the tamper
switch is disabled with this command.
This command affects both APU channels
simultaneously.
Specifies the length of time, in seconds,
Alarm Relay 1 to 10 1
that the alarm will remain active once an
Time (sec)
alarm condition is set.

Device 31 The alias under which the device will

Name APUNAME
characters communicate through the XML protocol.
maximum

Channel A 31 The name under which channel A will

Name CHA
characters communicate through the XML protocol.
maximum
31
Channel B characters CHB The name under which channel B will
Name maximum communicate through the XML protocol.

Adjusts the maximum frequency with which

XML Report 1 to 600 10
XML reports are output.
Interval (sec/10)

30
Appendix C. Warranty Information
A. Fiber SenSys warrants the FD322 APU to be free from electrical and mechanical defects in
materials and workmanship for a period of two years from the date of shipment. This warranty
does not apply to defects in the product caused by abuse, misuse, accident, casualty, alteration,
negligent use of current or voltages other than those specified by Fiber SenSys, application or
installation not in accordance with published instruction manuals, or repair not authorized by
Fiber SenSys. This warranty is made in lieu of any other warranty either expressed or implied.

B. All returns will be tested to verify customer claims of non-compliance with the warranty
described herein. If non-compliance is verified and is not due to customer abuse or the other
exceptions described previously, Fiber SenSys will, at its option, repair or replace the FD322
APU returned to it, freight prepaid. Contact Fiber SenSys and obtain an RMA number prior to
returning a product. Fiber SenSys will pay for ground return freight charges only. The Customer
must pay for any other return shipping options.

C. Fiber SenSys liability is limited to the repair or replacement of the product only, and not the
costs of installation, removal, or damage to user’s property or other liabilities. If Fiber SenSys is
unable to repair or replace a non-conforming product, it may offer a refund of the amount paid to
Fiber SenSys for such product in full satisfaction of its warranty obligation. Maximum liability to
Fiber SenSys is the cost of the product.

Fiber Defender FD322TM User Manual 31

Appendix D. Referenced Documents

AN-ENG-027 Site Design and Installation for FD300 series

AN-SM-007 Fiber Optics

AN-SM-008 Setting the Tuning Parameters

AN-SM-009 APU Networking

Note: It is possible to download these documents online from the Fiber Sensys web page:
www.fibersensys.com

Fiber Defender FD322TM User Manual 32