General Data and Information

Commissioning Service Department
Commissioning Standard Test Formats

Description : Pre check – 87T Relay Test Record No. :
Equip. No. : 87T-2 (R02.2) Contract no : GOSI-A-16-1
Contractor : CAPITAL LIGHTS CO. Drawing Ref: CD-814828
Substation No: 8340 Sheet No : Page 1 of 20
1. GENERAL DATA AND INFORMATION:
Bay Name : R02.2 (GT-2) Rated Voltage (Vn) : 100-120 V
Serial No. : MBHC16000089 Rated Current (In) : 1 /5 A
Manufacturer : GE Rated Aux. Voltage (Vx) : 110-250 VDC
Rly designation. : 87T-2 Frequency : 60 HZ
Model No. : T60 No. Of B/I & B/O : 16 I/P & 16 O/P
2. MECHANICAL CHECKS AND VISUAL INSPECTION:
ITEM DESCRIPTION CHECKED

1 Inspect for physical damage or defects.
2 Verify connections as per approved drawings.
3 Check tightness of all connections.
4 Check Ferrules
5 Check apparatus lists
3- ELECTRICAL TESTS
a) FUNCTION TEST:
ITEM DESCRIPTION CHECKED

1 Test switch / plug checked for correct function.
2 Alarm / Trip contacts checked.
3 All output contacts resistance measured <0.2Ω
4 Battery Fail Alarm Check
5 Date and Time Check
b) TRANSFORMER DATA:
Manufacturer : HYUNDAI
Rated Power: 50/67 MVA Vector Group: YNyn0+d
HV Rated Voltage 132 KV LV Rated Voltage 13.8 KV
HV Rated Current 218.7 A LV Rated Current 2092 A
Tested by Reviewed by
Name: P Ranjitkumar (PFL-017)
Signature:
Date: 02/08/2017
c) GLOBAL PROTECTION SETTINGS:
Transformer rating 50MVA
winding “HV” Voltage 132 kV
winding “LV”Voltage 13.8 kV
CT Ratio winding “HV”: 600/1
CT Ratio winding “LV” : 3600/1
Neutral CT Ratio winding “HV”: 600/1 (HV REF)
Neutral CT Ratio winding “LV”: 3600/1 (LV REF)
Neutral CT Ratio winding “LV”: 800/1 (LV SBEF)
VT Nominal secondary : 115 V
% Impedance 22
d) BURDEN TEST:
Relay status Supply Voltage (VDC) Measured Current (mA) Calculated Burden (VA)
Not operated 125 0.195 24.375
Operated 125 0.205 25.625
e) SECONDARY INJECTION TESTS:
1.1- Current Measurement Check:

Injection Measured Value
Winding Phase Expected Value (A)
Value (A)
L1 1.0 A 600 599.1A
HV Side L2 1.0 A 600 599.5A
L3 1.0 A 600 599.7A
L1 1.0 A 3600 3.59kA
LV Side L2 1.0 A 3600 3.59kA
L3 1.0 A 3600 3.59kA
HV Neutral LN1 1.0 A 600 599.7A
LV Neutral LN2 1.0 A 3600 3.59kA
LV SBEF LN3 1.0 A 800 798.9A
1.2- Voltage Measurement Check:

Injection Expected Value Measured Value
Winding Phase
Value in Volts (kV) (kV)
R-N 66.4 76.21 76.22
Y-N 66.4 76.21 76.20
B-N 66.4 76.21 76.12
HV Side
R-Y 115 132.0 131.81
Y-B 115 132.0 131.82
B-R 115 132.0 132.01
Signature:
Date: 02/08/2017
2- INPUTS, OUTPUTS & LEDS CHECKS:
OUTPUT RELAY CHECKS

Output
Terminal No. Type Function Assigned sheet Result
No.
O/P-1 H1 NO SPARE --
O/P-4 H4 NO 87T + 64NP + 64NS 30
O/P-5 P1 NO 87T + 64NP + 64NS 30
O/P-6 P2 NO 51S + 51NS + LV SBEF 30
O/P-7 P3 NO 50/51P 30
O/P-8 P4 NO HV CBF Trip 33
O/P-9 U1 NO HV CBF Trip 33
O/P-10 U2 NO CBF INITIATION TO LV 33
O/P-11 U3 NO SPARE --
O/P-12 U4 NC CBF INITIATION TO LV 33
BINARY INPUT CHECKS

Input No. Terminal No. Function Assigned Sheet No. Result
Input-1 H5a – H5b HV CBF Initiation 27
Input-2 H5c – H5b LV CBF Initiation 27
Input-3 H6a – H5b Protn. OUT 27
Input-4 H6c – H5b VT MCB Trip 27

Mechanical Protn. Trip to CBF
Input-5 H7a – H7b 27
Initiation
Input-6 H7c – H7b 94T-2 Optd. 27
Signature:
Date: 02/08/2017
Input-7 H8a – H7b 86T-2 Optd. 27
Input-8 H8c – H7b SPARE 27
Input-9 P5a – P5b Relay DC Fail 28
Input-10 P5c – P5b Indication DC Fail 28
Input-11 P6a – P5b AC supply Fail 28
Input-12 P6c – P5b 132 kV BB Protn. Optd. 28
Input-13 P7a – P7b CBF Protn. Optd. 28
Input-14 P7c – P7b SPARE 28
Input-15 P8a – P7b SPARE 28
Input-16 P8c – P7b SPARE 28
LED CHECK
LED No. Allocation (Function Assigned) Result
LED 1 XFMR PCNT DIFF OP
LED 2 XFMR PCNT DIFF OP A
LED 3 XFMR PCNT DIFF OP B
LED 4 XFMR PCNT DIFF OP C
LED 5 XFMR INST DIFF OP
LED 6 XFMR INST DIFF OP A
LED 7 XFMR INST DIFF OP B
LED 8 XFMR INST DIFF OP C
LED 9 XFMR PCNT DIFF 2ND A
LED 10 XFMR PCNT DIFF 2ND B
LED 11 XFMR PCNT DIFF 2ND C
LED 12 XFMR PCNT DIFF 5TH A
LED 13 XFMR PCNT DIFF 5TH B
LED 14 XFMR PCNT DIFF 5TH C
LED 15 RESTD GND FT1 OP
LED 16 RESTD GND FT2 OP
LED 17 PHASE TOC1 OP
LED 18 PHASE TOC1 OP A
Signature:
Date: 02/08/2017
LED No. Allocation (Function Assigned) Result

LED 19 PHASE TOC1 OP B
LED 20 PHASE TOC1 OP C
LED 21 NEUTRAL TOC1 OP
LED 22 NEUTRAL TOC2OP
LED 23 GROUND TOC1 OP
LED 24 GROUND IOC1 OP
LED 25 HV CBF INIT On(H5a)
LED 26 BKR FAIL 1 T1 OP
LED 27 LV CBF INIT On(H5c)
LED 28 BKR FAIL 2 T1 OP
LED 29 TCS-2 FAIL On (VO6)
LED 30 PHASE TOC2 OP
LED 31 PHASE TOC2 OP A
LED 32 PHASE TOC2 OP B
LED 33 PHASE TOC2 OP C
3- DIFFERENTIAL PROTECTION
HV CT Matching Factor = (HV rated volt * HV CT ratio)

(LV rated volt * LV CT ratio)
= (132000 * 600) / (13800 * 3600)
M1 = 1.59
LV CT Matching Factor = (LV rated volt * LV CT ratio)

(LV rated volt * LV CT ratio)
= (13800 * 3600) / (13800 * 3600)
M2 = 1.00
Differential Protection Settings:

Winding “HV” CT matching factor – M1 1.59
Winding “LV” CT matching factor – M2 1.00
Vector group reference HV-LV 0
Zero sequence filter on winding “HV” Not within Zone ( Off )
Zero sequence filter on winding “LV” Not within Zone ( Off )
Pick Up 0.3 PU
Slope-1 30 %
Slope-2 80 %
Break point-1 2 PU
Break point-2 3 PU
Instantaneous Pick up 5 PU
Signature:
Date: 02/08/2017
2nd Harmonic Inrush Current 10%

5th harmonic Over fluxing 20%
HV CT Terminals* Source-1
LV CT Terminals* Source-2
3.1 Checking the first section of tripping characteristics: (Zero Sequence Filter Off for All Windings)
Test method: (Zero sequence filtering disabled during this test for all windings, Vec. Group HV, LV=0).
Expected Operating Current = 0.3/M1 = 0.3/1.59 = 0.188A @HV side
=0.3/M2 =0.3/1 = 0.3A @LV side
Pick Up Drop off
Test Winding Expected operating current
current current
1-phase (L1 phase) HV 0.188 0.189 0.176
1-phase (L1 phase) LV 0.300 0.301 0.281
1-phase (L2 phase) HV 0.188 0.190 0.176
1-phase (L2 phase) LV 0.300 0.301 0.281
1-phase (L3 phase) HV 0.188 0.189 0.176
1-phase (L3 phase) LV 0.300 0.301 0.281
* Pick-up: formula ±0.5% of reading or ±1% of rated
* Drop-off: 97% to 98% of pick up (GE-T60 instruction manual page no: 56 of 788)
3.2) Checking the first section of tripping characteristics: (Zero Sequence Filter On for All Windings)
Test method:
(Zero sequence filtering enable during this test for all windings, Vec. Group HV, LV=0).
Expected Operating Current = (0.3/M1) / (2/3) = (0.3/1.59) / 0.67 = 0.281A @HV side
= (0.3/M2) / (2/3) = (0.3/1) / 0.67= 0.447A @LV side
(Factor of 0.67 for zero seq. filtering for single phase injection)
Test Winding Expected operating current Pick Up current Drop of current

1-phase (L1 phase) HV 0.281 0.283 0.265
1-phase (L1 phase) LV 0.447 0.451 0.422
1-phase (L2 phase) HV 0.281 0.283 0.265
1-phase (L2 phase) LV 0.447 0.451 0.422
1-phase (L3 phase) HV 0.281 0.283 0.265
1-phase (L3 phase) LV 0.447 0.451 0.422
3.3) Checking of second/third section of tripping characteristic:

Test method: (Zero sequence filtering disabled during test for both sides, Vec. Group =0).
Signature:
Date: 02/08/2017
Calculations:
Ib measured = Ib= (I1*M1+I2*M2)/2.
Id measured= (I1*M1)-(I2*M2)
First section of characteristics: Id calculated = K1*Ib
Third Section of characteristics: Id calculated = K2*Ib
A- First section of characteristics:
Id calculated = K1*Ib
Ib = 1.5 P.U
at unstable case: Id = 0.3 * 1.5 = 0.45 P.U
at stable case: Id = 0
I1 = (Id-+I2)/M1 I2 = Ib = 1.5A
I1 = (0.0+1.5)/1.59 = 0.943A
B- Second Section of characteristics:

I restraint between break point1 &2
Ib = 2.5 P.U
I1 = (Id-+I2)/M1 I2 = Ib = 2.5A
I1 = (0.0+2.5)/1.59 = 1.572A
C- Third Section of characteristics:
Id calculated = K2*Ib
Ib = 3.5 P.U
at unstable case: Id = 0.8 * 3.5 = 2.8 P.U
I1 = (Id-+I2)/M1 I2 = Ib = 3.5A
I1 = (0.0+3.5)/1.59 = 2.201A
Note: varied the phase angle of HV or LV current. Keep current magnitude constant for fix the bias constant.
L1-Phase
Signature:
Date: 02/08/2017
Winding Winding
Section of Restrain current Differential current
“HV” “LV” Measured
tripping ( with respect to Iref) ( with respect to Iref)
Injected Injected %Slope
char. Under
Current Current (Id/Ib)
test Calculated Measured Calculated Measured
A A
min pickup 0.314 0.500 0.5 0.499 0.30 0.301 Min. pick up
First (30%) 0.943 1.500 1.5 1.499 0.45 0.450 30.02 %
Second
1.572 2.500 2.5 2.500 1.430 57.20 %
(30%-80%) 1.5(approx.)
Third (80%) 2.201 3.500 3.5 3.500 2.80 2.807 80.20 %
L2-Phase
Winding Winding
char. Under
A A
First (30%) 0.943 1.500 1.5 1.499 0.45 0.449 29.95 %
Second
1.572 2.500 2.5 2.500 1.430 57.2 %
(30%-80%) 1.5(approx.)
Third (80%) 2.201 3.500 3.5 3.501 2.80 2.806 80.14 %
L3-Phase
Winding Winding
char. Under
A A
First (30%) 0.943 1.500 1.5 1.499 0.45 0.450 30.02 %
Second
1.572 2.500 2.5 2.500 1.427 57.08 %
(30%-80%) 1.5(approx.)
Third (80%) 2.201 3.500 3.5 3.502 2.80 2.805 80.09 %
3.4) checking of tripping Time: Expected Op Time: < 40 msec
Signature:
Date: 02/08/2017
Injected current = 1 Amps Operating time(msec) LED
L1 HV 20
L2 HV 19
L3 HV 21
L1 LV 20
L2 LV 19
L3 LV 20
3.5) Magnetizing Inrush Restraint (2nd Harmonic)
HV Side: I2h setting=10%

Injected 2nd
Applied Phase Injected (I1) Current 2nd Harmonic %
Harmonic Current
L1-Phase 1.0 0.100 10 %
L2-Phase 1.0 0.100 10 %
L3-Phase 1.0 0.100 10 %
LV Side: I2h setting=10%

Injected 2nd
Applied Phase Injected (I1) Current 2nd Harmonic %
Harmonic Current
L1-Phase 1.0 0.100 10 %
L2-Phase 1.0 0.100 10 %
L3-Phase 1.0 0.100 10 %
Note: Cross blocking verified: OK
3.6 Over fluxing 5th Harmonic Blocking:
HV Side: 20%
Injected 5th
Applied Phase Injected (I1) Current 5th Harmonic %
Harmonic Current
L1-Phase 1.0 0.199 19.9 %
L2-Phase 1.0 0.199 19.9 %
L3-Phase 1.0 0.199 19.9 %
LV Side: 20%
Injected 5th
Applied Phase Injected (I1) Current 5th Harmonic %
Harmonic Current
L1-Phase 1.0 0.199 19.9 %
L2-Phase 1.0 0.199 19.9 %
L3-Phase 1.0 0.199 19.9 %
3.7) INST. Differential: (Expected time less than 25 msec)

Expected Operating Current = (IS/M1) = 5/1.59 = 3.14A @HV side
Signature:
Date: 02/08/2017
= (IS/M2) = 5/1 = 5 A @LV side
Expected operating Time(msec) at 3*

Phase Pickup (Amps) LED
current I set
L1-HV 3.14 3.139 18
L2-HV 3.14 3.139 17
L3-HV 3.14 3.139 18
L1-LV 5.0 4.999 17
L2-LV 5.0 4.999 17
L3-LV 5.0 5.001 16
* Drop-off: 97% to 98% of pick up
* operating time ≤ 20 ms @ 3 * pick up at 60Hz (GE-T60 instruction manual page no: 56 of 788)
4. Restricted Earth Fault 64NP & 64NS:
4.1) HV REF:
Pick up 0.08 A
Slope 40 %
Op.time 0.8 A
Source HV
4.1.1) Pick Up And Drop Off Tests:

Pick up Value Drop off Value
Injected Current at
Calculated Measured Measured
R 0.080 0.081 0.078
Y 0.080 0.081 0.078
B 0.080 0.080 0.078
N 0.080 0.080 0.078
* Pick-up: formula ±0.5% of reading or ±1% of rated @ I < 2*CT rated
* Pick-up: formula ±1.5% of reading @ I > 2*CT rated (GE-T60 instruction manual page no: 57 of 788)
4.1.2) Trip Time Test:

REF Relay ( A )
Injected Current at Expected time Measured time at 2 X IREF
(m Sec) (m Sec)
R 0 20
Y 0 20
B 0 21
N 0 19
* operating time ≤ 1 power system cycle (GE-T60 instruction manual page no: 57 of 788)
4.1.3) Slope Test:
Slope= Id/Ib
Signature:
Date: 02/08/2017
Note: varied the phase angle of Phase or Neutral current. Keep current magnitude constant for fix the bias constant.
Injected Current in A Calculated values in A Measured Values in A

Phase
IPH IN I diff REF I diff REF I Bias REF Slope reg.
0.1 0.1 48.0 47.88 109.6 min. pick up
R
0.5 0.5 222.1 222.2 555.3 40.0 %
0.1 0.1 48.0 47.9 109.6 min. pick up
Y
0.5 0.5 222.7 221.2 556.8 39.73 %
0.1 0.1 48.0 47.9 109.7 min. pick up
B
0.5 0.5 222.5 221.8 556.1 39.88 %
4.2). LV REF:
Pick up 0.08 A
Slope 40 %
Op.time 0.8 A
Source LV
4.2.1) Pick Up And Drop Off Tests:

Pick up Value Drop off Value
Injected Current at
Calculated Measured Measured
R 0.08 0.08 0.078
Y 0.08 0.08 0.078
B 0.08 0.08 0.078
N 0.08 0.08 0.078
4.2.2) Trip Time Test:

Injected Current at REF Relay ( A )
Expected time Measured time at 2 X IREF
Signature:
Date: 02/08/2017
(m Sec) (m Sec)
R 0 20
Y 0 19
B 0 19
N 0 18
* operating time ≤ 1 power system cycle (GE-T60 instruction manual page no: 57 of 788)
4.2.3) Slope Test:
Slope= Id/Ib
Note: varied the phase angle of Phase or Neutral current. Keep current magnitude constant for fix the bias
constant.
Injected Current in A Calculated values in A Measured Values in A

Phase
IPH IN I diff REF I diff REF I Bias REF Slope reg.
0.1 0.1 288.0 287.5 657.10 min. pick up
R
0.5 0.5 1334.8 1330.1 3336.6 39.86 %
0.1 0.1 288.0 284.9 657.80 min. pick up
Y
0.5 0.5 1334.4 1327.4 3335.8 39.79 %
0.1 0.1 288.0 287.7 657.90 min. pick up
B
0.5 0.5 1334.1 1332.1 3335.1 39.97 %
5. HV OVERCURRENT & EARTH FAULT
5.1) Winding-1 OVERCURRENT (51)

- Pick-Up: ±5% of 1.05 I set or ± 20 mA.
- Drop-Off: ±5% of 0.95 I set or ± 20 mA.
Pick-Up and Drop-Off Test:

Pick-Up (Amps) Drop-Off (Amps)
I Setting Limit Limit
A B C A B C
0.5 P.U 0.501 0.501 0.501 0.487To 0.502 0.486 0.486 0.486 0.485-0.490
* Pick-up: formula ±0.5% of reading or ±0.4% of rated @ I < 2*CT rated
Timing Test:
Current Time meas. in sec.
IEC TMS/TIME Time cal. in sec.
multiple Rph Yph Bph 3ph
Signature:
Date: 02/08/2017
2 2.507 2.548 2.533 2.536 2.532

INV.A 5 0.25 1.069 1.092 1.091 1.090 1.085
8 0.824 0.844 0.839 0.848 0.845
2 3.375 3.414 3.408 3.410 3.412
INV.B 5 0.25 0.843 0.865 0.860 0.866 0.864
8 0.482 0.499 0.503 0.503 0.499
2 6.666 6.730 6.724 6.733 6.720
INV.C 5 0.25 0.833 0.857 0.855 0.856 0.851
8 0.317 0.337 0.333 0.337 0.336
2 0.444 0.469 0.467 0.468 0.464
ST.INV. 5 0.25 0.188 0.209 0.207 0.204 0.201
8 0.144 0.159 0.161 0.166 0.159
2 1.000 1.022 1.016 1.024 1.016
DFT 5 1.0 1.000 1.014 1.015 1.015 1.009
8 1.000 1.019 1.013 1.021 1.021
* operating time ±3.5% of operating time or ± 1/2 power system cycle (GE-T60 instruction manual page no: 57 of 788)
T = (K*Tm) / ((I/I s) ^ α – 1)) sec.
For Inv.A: K=0.14, α=0.02 For Inv.B: K=13.5, α=1 For Inv.C: K=80, α=2 For STI: K=0.05, α=0.04
(GE-T60 instruction manual page no: 365 of 788)

A B C A B C
2.0 2.002 2.002 2.002 1.99 - 2.01 1.942 1.942 1.942 1.94 - 1.96
Timing Test:
IEC TIME Time cal. in sec.
DT 2 0.0 0.00 0.016 0.019 0.019 0.015
* operating time ±3% of operating time or ± 1/4 power system cycle (GE-T60 instruction manual page no: 57 of 788)
5.3 Winding-1 Earth fault (51N)

N N
0.25A 0.251 0.249 – 0.251 0.244 0.242 – 0.245
Timing Test
Signature:
Date: 02/08/2017
Current
IEC TMS/TIME Time cal. in sec. Time meas. in sec.
multiple
Signature:
Date: 02/08/2017
2.507 2.579
2 1.069 1.106
INV.A 0.25
5 0.824 0.857
8 3.375 3.490
2 0.843 0.882
INV.B 0.25
5 0.482 0.510
8 6.666 6.905
2 0.833 0.868
INV.C 0.25
5 0.317 0.345
8 0.444 0.484
2 0.188 0.215
ST.INV. 0.25
5 0.144 0.172
8 1.000 1.026
2 1.000 1.024
DFT 1.0
5 1.000 1.019
T = (K*Tm) / ((I/I s) ^ α – 1)) sec.
5.4) Winding-1 Earth fault (50N)

A A
2.0A 2.137 1.99 – 2.01 2.073 1.94 – 1.96
* For single phase injection Pick-up: 0.9375 *I injected (GE-T60 instruction manual page no: 376 of 788)
Timing test
Current
IEC TIME Time cal. in sec. Time meas. in sec.
multiple
DT 2 0.00 0.00 0.021
6: LV OVERCURRENT & EARTH FAULT
Signature:
Date: 02/08/2017

A B C A B C
0.5A 0.501 0.502 0.502 0.498 – 0.502 0.486 0.486 0.486 0.485 – 0.490
Timing Test :

IEC TMS/TIME Time cal. in sec.
2 2.530 2.536 2.535 2.539 2.536
INV.A 5 0.25 1.091 1.089 1.089 1.089 1.086
8 0.843 0.845 0.843 0.846 0.845
2 3.397 3.414 3.408 3.415 3.413
INV.B 5 0.25 0.864 0.864 0.859 0.861 0.866
8 0.501 0.507 0.505 0.502 0.500
2 6.678 6.740 6.736 6.726 6.719
INV.C 5 0.25 0.850 0.851 0.855 0.855 0.851
8 0.335 0.336 0.337 0.343 0.335
2 0.444 0.472 0.470 0.475 0.468
ST.INV. 5 0.25 0.188 0.209 0.200 0.203 0.204
8 0.144 0.162 0.158 0.162 0.158
2 1.000 1.018 1.021 1.020 1.021
DFT 5 1.000 1.000 1.020 1.010 1.022 1.011
8 1.000 1.010 1.021 1.010 1.014
T = (K*Tm) / ((I/I s) ^ α – 1)) sec.

A B C A B C
2.0 2.002 2.002 2.002 1.997 – 2.030 1.944 1.944 1.944 1.994 – 1.996
Timing test
IEC TIME Time cal. in sec.
multiple R ph Y ph B ph 3ph
Signature:
Date: 02/08/2017
DT 2 0.00 0.00 0.017 0.014 0.018 0.016


N N
0.25A 0.251 0.249 - 0251 0.243 0.242 – 0.245
Timing test
Current
IEC TMS/TIME Time cal. in sec. Time meas. in sec.
multiple
2 2.530 2.580
5 0.25 1.091 1.109
INV.A
8 0.843 0.852
2 3.397 3.475
5 0.25 0.864 0.880
INV.B
8 0.501 0.510
2 6.678 6.891
5 0.25 0.850 0.875
INV.C
8 0.335 0.344
2 0.444 0.484
5 0.25 0.188 0.215
ST.INV.
8 0.144 0.172
2 1.000 1.027
5 1.0 1.000 1.020
DFT
8 1.000 1.020
T = (K*Tm) / ((I/I s) ^ α – 1)) sec.

A A
2.0 2.136 1.99 – 2.01 2.073 1.94 – 1.96
* For single phase injection Pick-up: 0.9375 *I injected (GE-T60 instruction manual page no: 376 of 788)

Signature:
Date: 02/08/2017
Timing test
Current
multiple
DT 2 0.00 0.00 0.020
7. LV Stand By Earth Fault (51NS):

A A
0.1 0.101 0.099 – 0.101 0.098 0.097 – 0.098
Timing test
Current
multiple
DT 2 1.0 1.0 1.029
7.2) LV Stand By Earth Fault (50NS):

A A
1.0 1.001 1.97 – 2.03 0.972 1.94 – 1.96
Timing test
Current
multiple
DT 2 0.00 0.00 0.016
8. Neutral Current Alarm :

Signature:
Date: 02/08/2017

A A
0.1 0.101 0.1 0.098 0.097 – 0.098
Timing test
Current
multiple
DT 2 5.0 5.0 5.05
9. HV CBF Protection 50BF:
I > 0.10 Time-2 = 150 msec.
PICK UP AND DROP OFF TEST

PICK-UP CURRENT DROP-OFF CURRENT
SETTING PHASE PHASE
VALUE
R Y B R Y B
0.10 0.101 0.101 0.101 0.098 0.098 0.098
TIMING TEST:
I set Stage-1 Set Time Operating Time at 2 I set (msec)

AMPS (msec) R Y B
0.10 150 169 170 169
10. LV CBF Protection 50BF:
Signature:
Date: 02/08/2017
I > 0.10 Time-2 = 150 msec.
PICK UP AND DROP OFF TEST

PICK-UP CURRENT DROP-OFF CURRENT
I SETTING PHASE PHASE
VALUE
R Y B R Y B
0.10 A 0.101 0.101 0.101 0.098 0.098 0.098
TIMING TEST:
I set Stage-1 Set Time Operating Time at 2 I set (msec)

AMPS (msec) R Y B
0.10 150 170 169 168
TEST EQUIPMENT USED
EQUIPMENT SERIAL NO DUE DATE

FREJA 300 1102381 Nov 2017 21
FLUKE METER 23210213 Oct 2017 05
Signature:
Date: 02/08/2017

General Data and Information

Uploaded by

Copyright:

Available Formats

General Data and Information

Uploaded by

Document Information

Original Title

Copyright

Available Formats

Share this document

Share or Embed Document

Sharing Options

Did you find this document useful?

Is this content inappropriate?

Copyright:

Available Formats

General Data and Information

Uploaded by

Copyright:

Available Formats

Commissioning Service Department

Commissioning Standard Test Formats

Bay Name : R02.2 (GT-2) Rated Voltage (Vn) : 100-120 V

Serial No. : MBHC16000089 Rated Current (In) : 1 /5 A

Manufacturer : GE Rated Aux. Voltage (Vx) : 110-250 VDC

Rly designation. : 87T-2 Frequency : 60 HZ

2. MECHANICAL CHECKS AND VISUAL INSPECTION:

ITEM DESCRIPTION CHECKED

ITEM DESCRIPTION CHECKED

e) SECONDARY INJECTION TESTS:

1.1- Current Measurement Check:

1.2- Voltage Measurement Check:

OUTPUT RELAY CHECKS

O/P-4 H4 NO 87T + 64NP + 64NS 30

O/P-5 P1 NO 87T + 64NP + 64NS 30

O/P-6 P2 NO 51S + 51NS + LV SBEF 30

O/P-8 P4 NO HV CBF Trip 33

O/P-9 U1 NO HV CBF Trip 33

O/P-10 U2 NO CBF INITIATION TO LV 33

O/P-12 U4 NC CBF INITIATION TO LV 33

BINARY INPUT CHECKS

Input-1 H5a – H5b HV CBF Initiation 27

Input-2 H5c – H5b LV CBF Initiation 27

Input-3 H6a – H5b Protn. OUT 27

Input-4 H6c – H5b VT MCB Trip 27

Input-7 H8a – H7b 86T-2 Optd. 27

Input-8 H8c – H7b SPARE 27

Input-9 P5a – P5b Relay DC Fail 28

Input-10 P5c – P5b Indication DC Fail 28

Input-11 P6a – P5b AC supply Fail 28

Input-12 P6c – P5b 132 kV BB Protn. Optd. 28

Input-13 P7a – P7b CBF Protn. Optd. 28

Input-14 P7c – P7b SPARE 28

Input-15 P8a – P7b SPARE 28

Input-16 P8c – P7b SPARE 28

LED No. Allocation (Function Assigned) Result

HV CT Matching Factor = (HV rated volt * HV CT ratio)

LV CT Matching Factor = (LV rated volt * LV CT ratio)

Differential Protection Settings:

2nd Harmonic Inrush Current 10%

Test Winding Expected operating current Pick Up current Drop of current

3.3) Checking of second/third section of tripping characteristic:

B- Second Section of characteristics:

C- Third Section of characteristics:

3.4) checking of tripping Time: Expected Op Time: < 40 msec

Injected current = 1 Amps Operating time(msec) LED

3.5) Magnetizing Inrush Restraint (2nd Harmonic)

HV Side: I2h setting=10%

LV Side: I2h setting=10%

3.6 Over fluxing 5th Harmonic Blocking:

3.7) INST. Differential: (Expected time less than 25 msec)

Expected operating Time(msec) at 3*

4. Restricted Earth Fault 64NP & 64NS:

4.1.1) Pick Up And Drop Off Tests:

4.1.2) Trip Time Test:

Injected Current in A Calculated values in A Measured Values in A

4.2.1) Pick Up And Drop Off Tests:

4.2.2) Trip Time Test:

4.2.3) Slope Test: