Honeywell

HON-FIN4000xxK-10K
Honeywell
15:02:55
(1/5000) U

V1.3
This manual is provided for information purpose only. All information included
herein is subject to change without notice. Honeywell is not responsible for any
changes, direct or indirect, arising from or related to us of this manual.

ⓒ Copyright 2013 Honeywell International Inc. All Rights Reserved.

2
 Contents

Safety Instructions ....................................................................................................5

1. Before Use .............................................................................................................6
1.1 Components .................................................................................................................. 6
1.2 Body .............................................................................................................................. 7
1.3 Methods for Fingerprint Input ......................................................................................... 8
1.4 System Setup Procedure ............................................................................................. 10
1.4.1 Registering the Initial Administrator ....................................................................... 11
1.4.2 Network Configuration ........................................................................................... 12
1.5 Authorization Methods ................................................................................................. 15
1.5.1 Finger Only ........................................................................................................... 15
1.5.2 Finger or PIN......................................................................................................... 16
1.5.3 Finger and PIN ...................................................................................................... 19
1.5.4 PIN Only ............................................................................................................... 20
1.5.5 Card Only .............................................................................................................. 21
2. User Management................................................................................................22
2.1 Enrolling a User ........................................................................................................... 22
2.1.1 Registration on the terminal................................................................................... 22
2.1.2 Registration on a Card .......................................................................................... 25
2.2 Editing a User .............................................................................................................. 27
2.3 Deleting a User............................................................................................................ 30
3. Configuration for Screen and Sound .................................................................31
3.1 Date, Time ................................................................................................................... 31
3.2 Backlight...................................................................................................................... 32
3.3 Sound.......................................................................................................................... 34
4. Device Configuration ..........................................................................................35
4.1 Authorization ............................................................................................................... 35
4.2 In/Out .......................................................................................................................... 40
4.3 System ........................................................................................................................ 43
5. Attendance Management ....................................................................................47
5.1 Operating environment ................................................................................................ 47
5.2 Setup for attendance management .............................................................................. 48
5.3 Operation modes ......................................................................................................... 49
5.3.1 Key Input............................................................................................................... 49
5.3.2 Manual .................................................................................................................. 49
5.3.2 Auto ...................................................................................................................... 50
5.3.3 Fixed ..................................................................................................................... 51
6. FAQ .......................................................................................................................52
6.1 Error messages ........................................................................................................... 52
6.2 Troubleshooting ........................................................................................................... 53
6.3 Usage summary .......................................................................................................... 54
6.4 System Installation ...................................................................................................... 55
6.4.1 Cable specifications .............................................................................................. 55
3
 6.4.2 Installing the bracket ............................................................................................. 56
6.4.3 Connecting Power & RS-485 ................................................................................ 57
6.4.6 Connecting Network ............................................................................................. 57
6.4.7 Connecting to a Controller .................................................................................. 58
6.4.8 Electrical specifications ......................................................................................... 59
6.5 Specifications .............................................................................................................. 60
6.6 FCC Notice ................................................................................................................. 62

4
Safety Instructions

Installation

Do not arbitrarily install or Use the power adapter

repair the product. provided or one for 12V 0.5A
The warranty does not apply to or above.
any product damage When sharing the power with
caused by an other devices check the power
arbitrary capacity considering power
installation or requirements for each device.
repair. If appropriate power is not used,
it may not operate normally.

In Use

Endure that password does Be cautioned for the

not exposed to unauthorized fingerprint contact area not
individuals. Frequent change to be contaminated or
of password is damaged by dirty hands or
recommended. foreign materials.
Any illegal access to It may affect fingerprint
your product may recognition performance
happen. or cause a failure.

Do not forcibly press the Do not clean the device with

buttons of the product and any form of liquid. Use soft
avoid any contact with sharp and dry cloth only.
object to the device.
It may cause
a failure.

5
1. Before Use
1.1 Components

Main Body Wall mounting bracket Extended bracket

(Option)

Fixing Screws Knife Blocks Shrinkable Ethernet Connector

(2 EA) (2 EA) Tubes

Star-shape wrench Adapter

(For fixing bracket) (Optional)

The components shown above may differ depending on the installation

environment.

6
1.2 Body HON-FIN4000xxK-10K

LCD Display

Key Pad

LED Lamp

Fingerprint Touch Area

(5) RF Card reading part

No. Name Description

1 LCD Display The operation status is displayed.

2 Key Pad 0–9 Buttons: Used to enter the ID and password.

< > Arrow Buttons: Used to move the selected item.
Button: Used to select the desired function.
Button: Used to enter or exit the menu.
Button: Used to exit from the menu or cancel the desired action.

3 LED Lamp The operation status is displayed with an alert sound.

– Green (Sound: beep beep beep!): Authorization success
– Red (Sound: fast beep beep beep!) : Authorization failure
– Pink (Sound: beep!) : Processing
– Blue and Yellow blink in turn at an interval of 2 seconds (No sound): No IP
address is given because DHCP is set in TCP/IP Setup.
– Blue and Sky Blue blink in turn at an interval of 2 seconds (No sound): Normal
operation.
– Red and Pink blink in turn at an interval of 2 seconds (No sound): Device locked
or no administrator.
– Blue and Red blink in turn at an interval of 2 seconds (No sound): The time is
reset due to battery discharge.
– At first use, Red blinks at an interval of 2 seconds (No sound): Initialization
error, Consult with the manufacturer.
– In normal use, Red blinks at an interval of 2 seconds (No sound): On the
watch.
– Yellow blinks shortly (No sound): Entry standby or in communication for
getting an IP when DHCP is set in TCP/IP Setup.

4 Fingerprint Used to input a fingerprint for authentication.

Touch Area

7
1.3 Methods for Fingerprint Input
HON-FIN4000xxK-10K can easily recognize fingerprints even though the
angle and location of the pattern change. However, it is recommended to
properly input fingerprints for more precise recognition.

Selecting a finger on fingerprint enrollment

Up to two fingerprints can be enrolled for each user in preparation of

any abnormal situation like having a wounded finger or carrying an
object with a hand.
In the case of a low recognition, the user can register
the same fingerprint twice to increase the recognition
rate.
It is recommended to use the index or middle finger.
In case of other fingers, the recognition rate
decreases because it tends to be more difficult to
place the finger in the center of the sensor area.

How to proerply place a fingerprint

Place your finger firmly on the sensor area.
Adjust the finger so that its middle position can be located in the center
of the sensor.
When the finger is vertically placed or its angle goes astray, the
recognition may be a failure.

When enrolling your fingerprint, the first finger input window prompts.
Then register the desired finger on the terminal as shown in the figure
below.
When the re-entry window appears with a “tick” sound, re-enter the
previously enrolled finger. The fingerprint input is made twice.
(Gently push your finger on the sensor to have a full fingerprint.)

Place the first

Finger

8
 HON-FIN4000xxK-10K

In case fingerprint is not recognized normally

HON-FIN4000xxK-10K is designed to normally operate regardless of weather
change or the angle and location of the fingerprint to place.
However, the recognition rate may vary depending on the external environment or
fingerprint condition.

In abnormal cases, follow the directions below:

1. Retry after drying the wetness of your finger.
2. When your finger is too dry, retry after blowing on your fingertip.
3. When you have a cut on your registered finger, register another fingerprint.

Cautions while registering your fingerprint

The initial fingerprint registration is important.
Because the recognition process compares the scanned fingerprint with the
registered one, an abnormally registered fingerprint can cause a failure.

To increase the recognition rate, follow the directions below:

1. Put the center of your fingerprint on the middle of the sensor.
2. If you have a cut in your finger or your fingerprint is not clear enough, retry with
another finger.
3. When fingerprint recognition is in progress, do not move your fingerprint.

9
1.4 System Setup Procedure

Install the system according to the environment

Step 1 - Grasp the locations for installation site
- Install the system

Register an initial administrator

Step 2 - Register the initial administrator for setting devices (See 1.4.1).

Configure the system

Step 3 - Network configuration (see 1.4.2)

Test for system operation

Step 4 - Deliver the setting items to the customer.

Register users
Step 5 - Use the system after user registration (see 2.1).

10
1.4.1 Registering the Initial Administrator
HON-FIN4000xxK-10K

There is no administrator set for the product in the initial status. So register an
administrator to manage the device.

1. When the product is connected, a window Enter ID

appears as shown in the right figure. Enter an ID 1
and press OK.
Enroll Admin

3. When the password entry window appears, enter Enter PIN

the desired password and press OK.
****

Enroll

4. When the password re-entry window appears, Confirm PIN

enter the previously input password again and
****
press OK.
Enroll

5. The completion message window appears.

Completed

This procedure is necessary to temporarily configure the installation-

related settings. Modify the administrator information after the
installation is complete.

11
1.4.2 Network Configuration
The network configuration is required to connect HON-FIN4000-SW or other devices
via network. Configure the settings according to the communication environment in your
place.

[In case of configuring the network via Ethernet]

1. Connect the terminal to the computer that has HON-FIN4000-SW according to the
network environment after seeing “6.4.6 Connecting network.”

2. Configure the settings for TCP/IP port and server according to the installation
environment.
※ The following example explains how to directly connect the server PC without
using DHCP.

Item
TCP/IP
Device In/Out In/Out

Use ◀ /▶ buttons to Use ◀ /▶ buttons to Use ◀ /▶ buttons to

select the Device icon select the In/Out icon select the TCP/IP and
and press OK. and press OK. press OK.
DHCP IP Address Gateway
Not Use 192.168.1.35 192.168.1.10
TCP/IP TCP/IP TCP/IP

Use ◀ /▶ buttons to set Enter the IP address Enter the Gateway using
whether or not to use and press OK. numeric and arrow
DHCP and press OK. buttons and press OK.

Subnet Mask Port Server

255.255.255.0 1471 Use
TCP/IP TCP/IP TCP/IP

Enter IP address using Enter Port and Use ◀ /▶ buttons

numeric and arrow button press OK. to select the Use
and press OK. and press OK.

Server IP Server Port

192.168.1.30 1480
TCP/IP TCP/IP

Enter Server IP address Enter Server Port

using numeric and arrow and press OK.
button and press OK.
Cont.

12
 100Base-T support HON-FIN4000xxK-10K

Not support Completed

TCP/IP

Use ◀ /▶ buttons to The completion

set whether or not to message window
support 100Base-T appears.
and press OK.

When you exit from the menu before completing the TCP/IP
setting, the data is not stored so please finish the remaining
steps until the setting completion message appears.

※IP Address/Gateway/Subnet Mask Setup: If DHCP is used, the values for

IP address, gateway, and subnet mask are automatically assigned. Otherwise, set DHCP
to Not Use and enter the corresponding values.
(When the right arrow is pressed, “.” is entered while the left arrow deletes characters
one by one.)
※Server: To directly connect the server of HON-FIN4000-SW that enables
monitoring and setting the terminal, use Server for its setup and enter the values for
IP address and port number. (Refer to HON-FIN4000-SW manual.)
※TCP/IP Port, Server Port: Should be the same values defined in the dedicated
PC software. It is recommended to set the TCP/IP port to “1471” and Server to “1480.”
(When the port number is modified as you want, TCP/IP communication may not be active.)

13
[In case of configuring the network via RS-485]
1. Connect the terminal to the computer that has HON-FIN4000-SW.

2. Configure the settings for RS-485 according to the installation environment.

Item
Serial Conn.

Device In/Out In/Out

Use ◀ /▶ buttons to Use ◀ /▶ buttons to Use ◀ /▶ buttons to

select the Device icon select the In/Out icon select the Serial Conn.
and press OK. and press OK. and press OK.

Baudrate Termination
115200 Not Use Completed
Serial Conn. Serial Conn.

Use ◀/▶ buttons to Use ◀/▶ buttons to The completion

select 115200 for PC select Not Use for message window
connection speed and termination and press appears.
press OK. OK.

14
1.5 Authorization Methods HON-FIN4000xxK-10K

For changing the terminal authorization method, see the operation mode selection case
in “4.1 Authorization”.
To separately set the authorization method for each user, see “2.2 Editing a user”.

1.5.1 Finger Only

When the user authorization method is set to “Finger Only,” you can authenticate using
three different methods:

1. Fingerprint recognition
2. Fingerprint recognition after entering ID
3. Fingerprint recognition after identifying user card

Fingerprint recognition

Honeywell Access Granted

10:33:02 ID : 2

Input the fingerprint of The authentication

the user. result will appear.

Fingerprint recognition after entering ID

Enter ID
Honeywell
2
10:33:02

Enter the ID of the Input the fingerprint

user and press OK. of the user.

Access Granted
ID : 2

The authentication
result will appear.

15
 Fingerprint recognition after identifying user card

Honeywell
10:33:02

Place the user card on Input the fingerprint

the Honeywell logo. of the user.

Access Granted
ID : 2

The authentication
result will appear.

1.5.2 Finger or PIN

When the user authorization method is set to “Finger or PIN,” you can authenticate
using five different methods:

1. Fingerprint recognition
2. Fingerprint recognition after entering ID
3. Password entry after entering ID
4. Fingerprint recognition after identifying the user card
5. PIN entry after identifying the user card

Fingerprint recognition

Honeywell Access Granted

10:33:02 ID : 2

Input the fingerprint The authentication

of the user.
result will appear.

16
Fingerprint recognition after entering ID
HON-FIN4000xxK-10K

Enter ID
Honeywell
2
10:33:02

Enter the ID of the Input the fingerprint of

user and press OK. the user.
Access Granted
ID : 2

The authentication
result will appear.

PIN entry after entering ID

Enter ID Enter Finger or PIN

Honeywell
2 ****
10:33:02

Enter the ID of the Enter the password

user and press OK. of the user and
press OK.
Access Granted
ID : 2

The authentication result

will appear.

Fingerprint recognition after identifying user card

Honeywell
10:33:02

Place the user card on Input the fingerprint

the Honeywell logo. of the user.
Access Granted
ID : 2

The authentication
result will appear.

17
 PIN entry after identifying the user card

Enter Finger or PIN

Honeywell
****
10:33:02

Enter the password

Place the user card on of the user and
the Honeywell logo. press OK.

Access Granted
ID : 2

The authentication
result will appear.

18
1.5.3 Finger and PIN
HON-FIN4000xxK-10K

When the user authorization method is set to “Finger and PIN,” you can authenticate
using three different methods:

1. PIN entry after identifying fingerprint

2. PIN entry after entering ID and fingerprint
3. PIN entry after entering user card and fingerprint

PIN entry after identifying fingerprint

Enter PIN
Honeywell ****
10:33:02
Input the fingerprint Enter the password
of the user. of the user and
press OK.

Access Granted
ID : 2

The authentication
result will appear.

PIN entry after entering ID and fingerprint

Enter ID
Honeywell
2
10:33:02

Enter the ID of the Input the fingerprint

user and press OK. of the user.

Enter PIN
Access Granted
****
ID : 2

Enter the password The authentication

of the user and result will appear.
press OK.

19
 PIN entry after entering user card and fingerprint

Honeywell
10:33:02

Place the user card on Input the fingerprint

the Honeywell logo. of the user.

Enter PIN
Access Granted
****
ID : 2

Enter the password The authentication

of the user and result will appear.
press OK.

1.5.4 PIN Only

When the user authorization method is set to “PIN Only,” you can authenticate using
two different methods:

1. PIN entry after entering ID

2. PIN entry after identifying user card

PIN entry after entering ID

Enter ID Enter Finger or PIN

Honeywell
2 ****
10:33:02

Enter the ID of the Enter the password

user and press OK. of the user and
press OK.

Access Granted
ID : 2

The authentication
result will appear.

20
 HON-FIN4000xxK-10K

PIN entry after identifying user card

Enter Finger or PIN

Honeywell
****
10:33:02

Enter the password

Place the user card on of the user and
the Honeywell logo. press OK.

Access Granted
ID : 2

The authentication result will

appear.

1.5.5 Card Only

When the user authorization method is set to “Card Only,” you can authenticate by
following the instructions below:

Honeywell Access Granted

10:33:02 ID : 2

The authentication
Place the user card on result will appear.
the Honeywell logo.

For “Card Only,” register the card user on HON-FIN4000-SW first.

21
2. User Management
The user management and other environment settings can be updated after authorizing
the registered administrator (see 1.4.1 “Registering the Initial Administrator”).

2.1 Enrolling a User

2.1.1 Registration on the terminal
The information of a new user can be saved on the terminal.

1. Use ◀ /▶ buttons to select the User ( ) icon

and press OK.

User

2. Use ◀ /▶ buttons to select Enroll ( ) icon and

press OK.

Enroll

3. The ID that can be used appears. Use it or enter

Enter ID
another ID and press OK.
3
(1–8 digit number)
Enroll

ID is used to edit or delete the user data so

please keep it carefully.

4. Use ◀ /▶ buttons to select Device on the Enroll

Enroll To
To and press OK.
※ You can save the user information Device

(including finger print) on your terminal or Enroll

card.

22
5. Use ◀ /▶ buttons to select a card ID entry type Card
and press OK. Not Use
※Not Use/Read Card/Manual Input/User ID Enroll

※Card ID: Not Use/Read Card/Manual Input/User ID

- Not Use: Only the finger print data is saved.
- Read Card: The card ID must be identified by touching the card on the HON-FIN4000xxK-10K

terminal.
- Manual Input: The card ID (maximum 10 digits) must be directly entered.
- User ID: The selected User ID is used as Card ID (Card ID=User ID)

In case of Read Card

Card ID
Card
2691057484
Read Card Place the Card Facility Code
Enroll 0

Use ◀ /▶ buttons Place the user card on When identified, enter

to select Read Card the HONEYWELL logo. the Facility Code.
and press OK.

In case of Manual Input

Card Card ID Facility Code (0-255)

Manual Input 2691057484

Manual Input Manual Input
Enroll

Use ◀ /▶ buttons to Directly enter the card Enter the Facility Code.
select Manual Input ID through the keypad.
and press OK.

6. Use ◀ /▶ buttons to select Level and press OK.

Level
(Level: General /Administrator)
General
※The user enrollment and environment configuration
are enabled only in Administrator level. Enroll

23
7. Enter the finger or PIN depending on the operation mode.
st st nd
(Password: 4–8 digit number, Fingerprint: 1 finger or 1 + 2 fingers)

Enter the required information after selecting Device > Authorization

> Operation Mode > Auth Mode.

Finger Only/Finger or PIN/Finger and PIN

Place the second

Place the first Place the first
finger
finger finger again
(Skip=ESC)

Place the first finger Place the same finger Place the second
on the sensor. on the sensor again. finger in the same
manner.

※In order to skip the second fingerprint enrollment after enrolling the first
fingerprint, press ESC.
※The user can enroll one or two fingerprints.

PIN Only/ Finger and PIN

Enter PIN Confirm PIN

***** *****
Enroll Enroll

※For password, it is recommended to enter 4 to 8 digit number not to be easily

exposed.

8. When the user enrollment is successfully done,

the completion message window appears. Completed
※User can be enrolled up to maximum 5000.

24
2.1.2 Registration on a Card
The information of a new user can be saved on a card.

1. Use ◀ /▶ buttons to select the User ( ) icon

and press OK.

User HON-FIN4000xxK-10K

2. Use ◀ /▶ buttons to select Enroll ( ) icon and

press OK.

Enroll

3. The ID that can be used appears. Use it or enter

Enter ID
another ID and press OK.
3
(1–8 digit number)
Enroll

ID is used to edit or delete the user data so

please keep it carefully.

4. Use ◀ /▶ buttons to select Card on the Enroll

To and press OK. Enroll To

※ You can save the user information Card

(including finger print) on your terminal or Enroll
card.

Only a rewritable card such as Mifare card can

save the user information.

5. Use ◀ /▶ buttons to select Level and press OK.

Level
(Level: General /Administrator)
General
※The user enrollment and environment configuration
are enabled only in Administrator level. Enroll

25
6. Use ◀ /▶ button to select Card Type and press
Card Type
OK.
Bypass Card
※Bypass Card/Use Template
Enroll

※Card: Bypass Card/Use Template

- Bypass Card: User can be authorized using a card only. The user information is
saved by touching the card.
- Use Template: User can be authorized by touching the card and then fingerprint.

In case of Bypass Card

Card Type

Bypass Card Place the Card Completed

Enroll
When the user enrollment
Use ◀ /▶ buttons to Place the user card on
is successfully done,
select Bypass Card the divice’s logo area.
the completion message
and press OK. window appears.

In case of Use Template

Card Type Enter PIN(skip=ESC)

Place the first
Use Template ****
finger
Enroll Enroll
Use ◀ /▶ buttons to Place the desired finger Enter the PIN
select Use Template on the sensor for entry.
and press OK. * (1 to 4)

Place the Card Completed

Place the user card on When the user enrollment is

the Honeywell Logo. successfully done, the completion
message window appears.

※In case of Mifare card, the 1K card can save up to 2 fingerprint data but the 4K
card up to 4. The card layout information can be set using the PC software.

26
2.2 Editing a User
You can modify the data of the previously enrolled user.

1. Use ◀ /▶ buttons to select the User ( ) icon

and press OK.

User HON-FIN4000xxK-10K

2. Use ◀ /▶ buttons to select the Edit ( ) icon

and press OK.

Edit

3. Enter the ID or fingerprint of the desired user and

Enter ID/Finger
press OK.
4

Edit

4. Use ◀ /▶ buttons to select the desired item and press OK.

※ select any of Level/Operation Mode/Security Level/Finger/PIN

Changing the user level

Item Level

Level General

Edit Edit

Use ◀ /▶ buttons Use ◀ /▶ buttons Press OK.

to select Level and to select General or
press OK. Administrator.

※The settings for user, screen/sound, device, and such can be configured
only by the administrator level.

27
 Changing the authorization method

Item Operation Mode

Operation Mode Finger Only

Edit Edit

Use ◀ /▶ buttons to Use ◀ /▶ buttons Press OK.

select Operation Mode to select an desired
and press OK. operation mode and
press OK.

This authorization method setting for each user has higher priority than
the terminal setting that has been defined in Device > Authorization
> Operation Mode > Auth Mode. Note that this function is applied to
the case when the user enters ID or card and when Use is set in
Device > Authorization > Operation Mode > Private Auth Mode.

※Authorization methods: *Finger Only/PIN Only/Finger or PIN

/ Finger and PIN/Card Only/Per Device
- Finger Only: Only fingerprint is used.
- PIN Only: Only PIN is used.
- Finger or PIN: Fingerprint or PIN is used.
- Finger and PIN: Both fingerprint and PIN are used.
- Card Only: Only user card is used.
- Per Device: The mode set in “Device > Authorization > Operation Mode >
Auth Mode” is used.

Changing the security level of the user

Item Security Level

Security Level Normal

Edit Edit

Use ◀ /▶ buttons to Use ◀ /▶ buttons Press OK.

select Security Level and to select a security
press OK. level.

※Security Level: *Per Device/Lower/Low/Normal/High/Higher

- Per Device: The security level in “Device>Authorization>Fingerprint>”
on page 40 is applied.
- The higher the security level, the more sensitive the fingerprint recognition.
But the authorization failure rate can increase.

28
Changing the fingerprint of the user

Item
Fingerprint Place the first Place the first
finger finger again
Edit

Use ◀ /▶ buttons to Place the first finger on Place the same finger
select Fingerprint and the sensor. on the sensor again.
press OK.
HON-FIN4000xxK-10K
Place the second
finger
Enroll the second fingerprint
(Skip=ESC) in the same manner.

Changing the PIN of the user

Item Enter PIN Confirm PIN

PIN **** ****

Edit Edit Edit

Use ◀ /▶ buttons to Enter the desired After re-entering the

select PIN and press OK. password and press password of the
OK. user, press OK.

Changing the card

Item Card
Card Read Card
Edit Edit

Use ◀ /▶ Use ◀ /▶ buttons to Press OK.

buttons to select select card input type
Card and press * Not use/ Read Card/
OK. Manual Input / User ID

※Card: *Not use/Read Card/Manual Input/User ID

- Not use: Card is not used
- Read Card: User information is changed after touching a card on the terminal.
- Manual Input: User information is changed after entering the card ID.
- User ID: The corresponding user ID is changed using a card ID.

29
2.3 Deleting a User
You can delete unnecessary user data.

1. Use ◀ /▶ buttons to select the User ( ) icon

and press OK.

User

2. Use ◀ /▶ buttons to select the Delete ( ) icon

and press OK.

Delete

3. After entering the ID or finger to delete and press

Enter ID/Finger
OK.
4

Delete

4. When the action is successfully made, the

message Deletion appears.
Deletion
※The deleted user cannot be recovered.
If necessary, enroll it again.

- If all the users including the administrator are deleted, you must
register the initial administrator again (see 1.4.1).
- When an administrator is deleted by mistake except normal users,
the initial administrator registration step does not require registering
normal users.

30
3. Configuration for Screen and
Sound
3.1 Date, Time
You need to set the current system date and time.
After setting the date and time, the log data can store correct information.

1. Use ◀ /▶ buttons to select the Screen, Sound

( ) icon and press OK.
Screen, Sound

HON-FIN4000xxK-10K

2. Use ◀ /▶ buttons to select the Date, Time ( )

icon and press OK.

Date, Time

3. Enter the current date by following the suggested

Date(YYYYMM00)
format and press OK.
For example, in case of November 15 in 2008, 20081115

enter “20081115” and press OK. Date, Time

4. Enter the current time by following the suggested

Time(hhmmss)
format and press OK.
102055
For example, in case of 10:20 55 AM,
enter “102055” and press OK. Date, Time

31
3.2 Backlight
1. Use ◀ /▶ buttons to select the Screen, Sound
( ) icon and press OK.
Screen, Sound

2. Use ◀ /▶ buttons to select Backlight ( ) icon

and press OK.
Backlight

3. Use ◀ /▶ buttons to select a backlight operation Mode

status and press OK.
All On At use

Backlight

All On At Use
※ When no input is made
on the menu window, it
Mode Timeout(sec) sets the time to
automatically turn off the
All On At Use 20
LCD/Keypad backlight.
Backlight Backlight

Use ◀ /▶ buttons to Enter the backlight-on time

select the Always On At (second) on the menu
Use and press OK. window.

※When no input is made, it sets the time to exit from

Always On the menu.

Mode Timeout(sec)
Always On 20

Backlight Menu Duration

Use ◀ /▶ buttons to When no operation is made,

select the Always On and it sets the time (second) to
press OK. switch the screen.

32
On at Use ※When no input is made on the menu window, it sets
the time to automatically turn off the backlight.

Mode Timeout(sec)
On at Use 20

Backlight Backlight

Use ◀ /▶ buttons to Enter the backlight-on time

select the On at Use and (second) on the menu window.
press OK.

HON-FIN4000xxK-10K

33
3.3 Sound

1. Use ◀ /▶ buttons to select the Screen, Sound

( ) icon and press OK.
Screen, Sound

2. Use ◀ /▶ buttons to select Sound ( ) icon

and press OK.

Sound

3. Use ◀ /▶ buttons to select the sound operation status and press OK.

Mode Mode

Off Or On

Sound Sound

34
4. Device Configuration
4.1 Authorization
1. Use ◀ /▶ buttons to select the Device ( ) icon
and press OK.

Device

2. Use ◀ /▶ buttons to select the Authorization

( ) icon and press OK.

Authorization

3. Use ◀ /▶ buttons to select any of Fingerprint, Item

and Operation Mode and press OK. Fingerprint

Authorization

In case of Fingerprint
HON-FIN4000xxK-10K

Item Item Security Level

Fingerprint Security Level Normal

Authorization Fingerprint Fingerprint

Use ◀ /▶ buttons to Use ◀ /▶ buttons to Use ◀ /▶ buttons to select

select Fingerprint and select Security Level Security Level and press OK.
press OK. and press OK. * Normal /Secure/More Secure

Item Image Quality

Image Quality Normal

Fingerprint Fingerprint

Use ◀ /▶ buttons to Use ◀ /▶ buttons to

select Image Quality and select Image Quality and
press OK. press OK.
*Normal/High/Low

Cont.

35
 Item Sensitivity

Sensitivity 7

Fingerprint Fingerprint

Use ◀ /▶ buttons to Use ◀ /▶ buttons to

select Sensitivity and select Sensitivity level
press OK. and press OK.

Item Check Duplicate

Check Duplicate Not Use

Fingerprint Fingerprint

Use ◀ /▶ buttons to Use ◀ /▶ buttons Check

select Check Duplicate Duplicate and press OK.
and press OK. * Not Use /Use

Item Fast Mode

Fast Mode Auto
Fingerprint Fingerprint

Use ◀ /▶ buttons to Use ◀ /▶ buttons to

select Fast Mode and select desired Fast Mode
press OK. and press OK.
*Auto/Normal/Fast
/Faster

Item Scan Timeout(sec)

Scan Timeout 10
Fingerprint Fingerprint
Use ◀ /▶ buttons to Enter Scan Timeout
select Scan Timeout and (second) and
press OK. press OK.

Item Matching Timeout(sec)

Matching Timeout 3
Fingerprint Fingerprint

Use ◀ /▶ buttons to Enter Matching Timeout

select Matching (second)and press OK.
Timeout and press OK.

Cont.

36
 Item Template Type
Template Type HON-FIN4000
Fingerprint Fingerprint

Use ◀ /▶ buttons to Use ◀ /▶ buttons to

select Template Type select template format
and press OK. and press OK.
*HON-FIN4000/SIF

※ Security Level: The higher the security level, the more sensitive the fingerprint
recognition. But the authorization failure rate can increase.
※ Image Quality: It is the image quality level used when entering the fingerprint data.
In case of Low, the fingerprint can be easily input but the correct
authorization is not guaranteed.
※ Sensitivity: The higher the value, the more sensitive the sensor.
※ Check Duplicate: When enrolling a user, it determines whether or not to check the
fingerprint data is already enrolled.
※ Fast Mode: You can set the fingerprint recognition speed. If it is set to Fast,
the recognition accuracy may decrease.
※ Scan Timeout: You can set the terminal standby time for entering fingerprint.
If entry is not made within the specified time, the message,
‘Entry time is over” appears.
※ Matching Timeout: You can set the maximum authorization time after entering fingerprint.
If this time limit expires, matching stops and the authorization fails.
※ Template Type: Format used in the terminal when identifying fingerprints (HON-FIN4000/SIF)
- HON-FIN4000: HON-FIN4000’s own template format, SIF: ISO/IEC compatible template format
(To change the template format, there must be no fingerprint data stored on the terminal.) HON-FIN4000xxK-10K

37
 In case of Operation Mode

Item Use ◀ /▶ buttons to

Operation Mode select Operation
Mode an press OK.
Authorization

Item Sensor Mode Schedule

Sensor Mode Always On All Time
Operation Mode Operation Mode Always On
Use ◀ /▶ buttons to Use ◀ /▶ buttons to
Use ◀/▶ buttons to
select Sensor Mode select a sensor mode.
an press OK. *Always On/ID Entered/
select the applicable
OK Pressed time zone and press
OK.

※ Sensor Mode: *Always On/ID Entered/OK Pressed

- Always On: The sensor always waits for a fingerprint input.
- ID Entered/OK Pressed: If you enter ID or press OK, you can enter the time zone
for using the sensor.
※ Applied time: Use HON-FIN4000-SW for setting the time zone except
All Time and Not Use. With the terminal, you cannot add and edit it but only selection
is not possible.

Item Auth Mode Schedule

Auth Mode Finger Only All Time
Operation Mode Operation Mode Finger Only

Use ◀ /▶ buttons to Use ◀/▶ buttons to Use ◀/▶ buttons to

select Auth Mode and select the authorization select the applicable
press OK. method press OK. time zone and press
OK.

Double Mode ※Auth Mode: *Finger Only/PIN Only/Finger or PIN

/ Finger and PIN /Card Only
Not Use
If no authorization setting exists for each user,
Finger Only the user authorization method that has been set
on the terminal is applied.
Use ◀ /▶ buttons to
set whether or not to
※Double Mode: When consequent two users are
use the double mode
and press OK. authorized successfully, entrance
and exit are allowed.

Cont.

38
 Item Private Auth Mode
Private Auth Mode Use
Operation Mode Operation Mode

Use ◀ /▶ buttons to Use ◀/▶ buttons to

select Private Auth set whether or not to
Mode an press OK. use the mode and
press OK.

Item Card Type

Card Use Use Template
Operation Operation Mode Card

Use ◀ /▶ buttons to Use ◀/▶ buttons to set Use ◀/▶ buttons to

select Card an press OK. whether or not to use select the card entry
cards and press OK. method and press OK.
* Use Template/Use CSN

※Card entry methods (Available in HON-FIN4000MIK-10K Mifare):

- Use Template: After placing the user card, enter your fingerprint and PIN. Then the
terminal matches the enrolled fingerprint template with the template
in the card for identification. HON-FIN4000xxK-10K

- Use CSN: Identifies only the serial number of the card.

39
4.2 In/Out
1. Use ◀ /▶ buttons to select the Device ( ) icon
and press OK.

Device

2. Use ◀ /▶ buttons to select In/Out ( ) icon and

press OK.
In/Out

In case of Tamper On

Item Tamper On

Tamper On Ignore

In/Out In/Out
Use ◀ /▶ buttons to Use ◀ /▶ buttons Press OK.
select Tamper On and to select a tamper
press OK. method.

※ Tamper: *Ignore/Locked
- Locked: When the device is forcibly removed, the Device is locked.
(To release the lock, the administrator must perform authorization.)

40
In case of Wiegand
※Standard 26Bit Format is used for Wiegand In/Out format. The setting
can be changed using HON-FIN4000-SW.

Item Type
Wiegand Card ID In
In/Out Wiegand
Use ◀ /▶ buttons to Use ◀/▶ buttons to select
select Wiegand and Wiegand and press OK.
press OK. *Card ID In/ Card ID Out/User ID
In/ User ID Out/Not Use

※W iegand types: *Card ID In/Card ID Out/User ID In/User ID Out

- Card ID In: The card ID is entered.
- Card ID Out: The card ID is output.
- User ID In: The user ID is entered.
- User ID Out: The user ID is output.

When the user whose user ID is 2 registers the card ID (1234567),

- Card ID In: When “1234567” is entered through the Wiegand port, the
user is successfully authorized.
HON-FIN4000xxK-10K
- Card ID Out: When the user card is read through the terminal, the card ID
“1234567” is output through the Wiegand port.
- User ID In: When “2” is entered through the Wiegand port, the user is
successfully authorized.
- User ID Out: When the user is successfully authorized, the user ID “2” is
output through the Weigand port.

※For Wiegand connection, see “6.4.7 Connection Wiegand.”

41
 ※It directly connects to the server for HON-FIN4000-
In case of TCP/IP
SW without using DHCP.

Item DHCP IP Address

TCP/IP Not Use 192.168.1.35
In/Out TCP/IP TCP/IP
. Use ◀ /▶ buttons to Use ◀/▶ buttons to set Enter IP address and
select the TCP/IP and whether or not to use press OK.
press OK. DHCP and press OK.

Gateway Subnet Mask Port

192.168.1.10 255.255.255.0 1471
TCP/IP TCP/IP TCP/IP

Enter Gateway using Enter IP address using Enter Port and press
numeric and arrow numeric and arrow OK.
button and press OK. button and press OK.

Server Server IP Server Port

Use 192.168.1.30 1480
TCP/IP TCP/IP TCP/IP

Use ◀ /▶ buttons to Enter Server IP address Enter Server Port and

select the Use and using numeric and arrow press OK.
press OK. button and press OK.

100Base-T Support
Not Support
When you exit before
Completed
finishing the TCP/IP
TCP/IP setting, the change is
not stored so proceed
Use ◀ /▶ buttons to set The completion with the settings until
whether or not to message window
the message
support 100Base-T and appears.
press OK.
“Completed” appears.

※IP Address/Gateway/Subnet Mask Setup: If DHCP is used, the values for

IP address, gateway, and subnet mask are automatically assigned. Otherwise, set DHCP
to Not Use and enter the corresponding values.
(When the right arrow is pressed, “.” is entered while the left arrow deletes characters
one by one.)
※Server: To directly connect the server of HON-FIN4000-SW that enables
monitoring and setting the terminal, use Server for its setup and enter the values for
IP address and port number. (Refer to HON-FIN4000-SW manual.)
※TCP/IP Port, Server Port: Should be the same values defined in the dedicated
HON-FIN4000-SW. It is recommended to set the TCP/IP port to “1471” and Server to “1480.”
(When the port number is modified as you want, TCP/IP communication may not be active.)

42
4.3 System
1. Use ◀ /▶ buttons to select the Device ( ) icon
and press OK.
Device

2. Use ◀ /▶ buttons to select the System ( )

icon and press OK.

System

3. Use ◀ /▶ buttons to select any of Information, Item

Factory Default, Delete All Log, Delete User DB, Information

and Language and press OK. System

In case of Information

Item
Use ◀ /▶ buttons to
Log select Log and press OK.
Information

Filter 6/18 16:21(1) HON-FIN4000xxK-10K

Set Time
Not Use
6/18 14:20(3)
Log Delete OK
Use ◀ /▶ buttons to The entire logs appear.
select Not Use and (Use ◀ /▶ buttons to see
press OK. the previous/next logs.)

Filter User Date

Use All All

Log Filter Filter

Use ◀ /▶ buttons to Use ◀ /▶ buttons to Use ◀ /▶ buttons to

select Use and press select any of All and select any of All and
OK. Select ID and press OK. Specify Date and press OK.

6/18 14:20(3) ※ Filter

Event
- Not Use: Displays all.
Delete OK
All - Use: Only the specified log
6/18 13:46(3)
is displayed.
Filter Enroll OK
(ID/Date/Event Type)
Use ◀ /▶ buttons to select The log filtering result
the event type and press OK. appears on the screen. ※When the date is specified,
*All/Success/Failure/In/Out/ (Use ◀ /▶ buttons to see the logs occurred earlier than
System the previous/next logs.) the specified date appear.

43
 In case of Information — Continued

Item User
4/5000
Num. Of User Templates
Information 6/10000

Use ◀ /▶ buttons to The number of current users

select Num. Of User and the number of fingerprints
and press OK. enrolled appear.

Item Firmware Ver.

Firmware Ver. V1.0_081127

Information Information

Use ◀ /▶ buttons to The version of the

select Firmware Ver. firmware appears.
and press OK.

Item Hardware Ver.

Hardware Ver. 11563(HON-FIN4000)

Information Information

Use ◀ /▶ buttons to The version of the

select Hardware Ver. hardware appears.
and press OK.

In case of Factory Default

Item Initialize?

Factory Default Initialize Initialized

System Factory Default

Use ◀ /▶ buttons to Use ◀ /▶ buttons to In case of Initialize,

select Factory Default determine whether or the message
and press OK. not to initialize it. Initialized appears.
*Cancel/ Initialize

※In case of Initialize, the settings are deleted but the log data and user DB are not
deleted.

44
In case of Delete All Log

Item Delete?

Delete All Log Delete Deletion

System Delete All Log

Use ◀ /▶ buttons to Use ◀ /▶ buttons In case of Delete,

select Delete All Log and to determine the message
press OK. whether or not to Deletion appears.
delete them.
*Cancel/ Delete

※In this case, all users’ in/out data are deleted and they cannot be recovered.

In case of Delete User DB

Item Delete?

Delete User DB Delete Deletion

System Delete User DB

Use ◀ /▶ buttons to Use ◀ /▶ buttons In case of Delete,

select Delete User DB to determine the message
and press OK. whether or not to Deletion appears. HON-FIN4000xxK-10K
delete the user DB.
*Cancel/Delete

※In this case, the users’ DB is completely deleted so you must immediately
register the initial administrator (see 1.4.1).
※When the user DB is deleted, it cannot be recovered.

In case of Language

Item Item

Language English

System Language
Use ◀ /▶ buttons to Use ◀ /▶ buttons Press OK.
select Language and to select the
press OK. language.
* English/ Chinese

45
 In case of Wallpaper

Item Wallpaper
Wallpaper Type1
System System

Use ◀/▶ buttons to Use ◀/▶ buttons to

select Wallpaper and select the type and
press OK. press OK.
*Type1/Type2
※Types
- Type1: Only the time appears on the wallpaper screen.
- Type2: The number of users and TCP/IP connection status appears
on the wallpaper screen.
In case of (8/5000) U - Eight people are registered among 5000
(number of people that can be registered) and it is unlinked.

Honeywell
Honeywell
10:33:02
10:33:02 (8/5000) U

Type1 Type2
Characters on the Type2 wallpaper
- U: Unlinked (LAN is not connected.)
- D: Disconnected (LAN is connected but TCP/IP communication is not active.)
- C: Connected (LAN is connected and TCP/IP communication is active.)

In case of Contrast
Item Contrast ※Contrast
Contrast value on the
Contrast 17
screen (Range: 10 to 30)
System System

Use ◀ /▶ buttons Use ◀ /▶ buttons to

to select Contrast select contrast level.
and press OK.

In case of Format Card

Item
Format Card
Format Card Place the Card
Completed
System

Use ◀ /▶ buttons to Place the card on After formatting a card, The

select Format Card the Honeywell logo. format completion message
and press OK. window appears.

※ After formatting a card, the data on a rewritable card such as Mifare card
is removed. (The card format can be set using HON-FIN4000-SW.)

46
5. Attendance Management
5.1 Operating environment
When a T&A event (attendance, leaving, return, and outside duty) occurs on the
terminal, it will be saved within its internal DB.

HON-FIN4000-SW can define/modify T&A events and input them into the device.

Event

HON-FIN4000-SW HON-FIN4000xxK-10K

HON-FIN4000xxK-10K

47
5.2 Setup for attendance management

1. Use ◀ /▶ buttons to select the Device ( ) icon

and press OK.
Device

2. Use ◀ /▶ buttons to select the Authorization

( ) icon and press OK.
Authorization

3. Use ◀ /▶ buttons to select the Operation Mode Item

and press OK.
Operation Mode
Authorization

4. Use ◀ /▶ buttons to select the Time

Item
Attendance and press OK.
Time Attendance
Operation Mode
5. Use ◀ /▶ buttons to select the Operation Mode
of Time Attendance and press OK. Time Attendance
Key Input
Operation Mode

※Oper at ion modes: *Key Input/Fixed/Manual/Auto/Not Use

- Key Input: In usual time, the function is inactive. When ◀/▶ buttons are pressed,

Attendance Mgmt
you can select the attendance status. When a user authorization is successful,
the selected attendance log is recorded.
- Fixed: A specific attendance status continues. When a user authorization is successful,
the corresponding log is recorded.
- Manual: The active attendance status appears on the screen and it can be changed
using ◀/▶ buttons. Once it is changed, the status continues until another
selection is made. Every authorization success makes the log recorded.
- Auto: The active attendance status appears on the screen. Fore each time zone,
the active attendance statuses are fixed.
- Not Use: The function is not available.

48
5.3 Operation modes

5.3.1 Key Input

When the operation mode is set to “Key Input,” this mode is used.

Select
Honeywell In
10:33:02 Type

Select the desired

Move to the desired event and perform
event by using ◀ /▶ user authorization.
buttons.
ID: 8
In

Successful T&A
Authentication
Message

HON-FIN4000xxK-10K

5.3.2 Manual
When the operation mode is set to “Manual”, this mode is used.

In case of Manual

In
Honeywell 08:30:43
10:33:02 12/01/2008

The desired event

Move to the desired
appears.
event by using ◀ /▶
buttons.

49
 In case of Manual

In
ID: 8
08:30:43
In
12/01/2008

Successful T&A
Authentication
Message
The Users identify the card
or fingerprint according to
the authorization method.

※Manual: It is convenient to those who need to change an event type manually

every time they enter or leave..

5.3.2 Auto
When the operation mode is set to “Auto,” this mode is used.
This mode can set the corresponding time zone for each attendance event through
HON-FIN4000-SW. Then the fixed event is set for the corresponding time zone.

In case of Auto

Out
ID: 8
18:35:55

Attendance Mgmt
Out
12/01/2008

The event for the Successful T&A

corresponding time Authentication
zone appears. Message
The users identify the card
or fingerprint according to
the authorization method.

※Aut o: While the event type and time zone are set through HON-FIN4000-SW, you
can totally use this mode for all the users who are entering or leaving.

50
5.3.3 Fixed
When the operation mode is set to “Fixed,” this mode is used.
This mode is used after fixing the event through HON-FIN4000-SW if required.
In this case, the setting can be changed only through HON-FIN4000-SW and you
cannot change the attendance event through the terminal.

Out
ID: 8
18:35:55
Out
12/01/2008

The preset event Successful T&A

appears. Authentication
Message
The users identify the card
or fingerprint according to
the authorization method.

※ Fixed: This mode is available only when the desired event is set for all the users
who are entering or leaving.

HON-FIN4000xxK-10K

51
6. FAQ
6.1 Error messages
Error Message Description

!Cannot Change A template already exists when you want to change the template format.

!Cannot Format The card is not formatted due to improper card touch.

!Cannot Write The user information is not saved due to improper card touch.

!Device Locked The device is locked because the case has been open.

!Duplicate Card The card has been already registered.

When enrolling a user fingerprint, the fingerprint that has been input
!Duplicate Finger
already exists in the device (when checking the duplicated case).

!Duplicated Time The time zone is duplicated.

!Failed The number of users exceeds 5000, so you cannot enroll more users.

!Failed The user ID to delete does not exist.

!ID In Use The user ID to enroll already exists.

!Invalid Value An invalid value is entered.

!Mode Error The authorization mode is different from the setting.

!No Card You tried authorization with a unregistered card.

!No Log There is no log data.

!Not Administrator A normal user tries to enter the menu.

The fingerprint authentication for the administrator fails when entering the
!Not Authorized
menu.

The entered fingerprint or password is not matched to the enrolled one.

!Not Matched - In case of fingerprint entry, the entered two fingerprints of the same
finger are different.

!Not Recognizable The fingerprint data cannot be extracted due to wrong finger input.

!Time Out The fingerprint data is not entered while the sensor is active.

The entered fingerprint for entering the menu or editing/deleting a user

!Unknown Finger
data does not exist.

!Unknown ID The user ID that does not exist in the device is entered.

!Wrong PIN The entered password for authentication is not matched the enrolled one.

52
6.2 Troubleshooting
Category Trouble Solution
The power is - When the device is disconnected from the bracket, it
supplied but the may not work when using the tamper switch.
Power device does not - Check the adapter or power cable.
operate.
The password is lost. - Enter the queried password after contacting the
administrator in case of a normal user.
Password - When the administrator password is lost, contact with the
installation agency.
The fingerprint has - HON-FIN4000xxK-10K has the technology of Honeywell
been enrolled but its that won the first award in FVC2004 and FVC2006
recognition because it has world number one quality in recognition.
encounters an error. - For better performance in fingerprint recognition, correct
registration is a must.
- Enroll the fingerprint again after seeing
“1.4 Methods for Fingerprint Input”
- The recognition rate may vary due to the characteristic of
Fingerprint each finger so enroll the fingerprint of another finger.
It was good at - Check whether the finger or the sensor is covered with
recognizing sweat, moisture, or dust.
fingerprints but - In case the fingerprint has any damage, the device may
suddenly it fails in consider it as the one of wrong person.
recognition. - Wipe the finger or sensor with a dry cloth and retry.
- When the fingerprint is so dry, blow your steam of breath
into it and retry.
The time is not - HON-FIN4000xxK-10K has an embedded battery but it
correct. can be discharged by a long time use. Accordingly the
Time time may not be correct. Correct the time after seeing
“3.1 Date, Time.”

The terminal data is - Check the connection status after setting on the terminal
not found by HON- like Terminal > System > Wallpaper > Type2.
FIN4000-SW. - When U is displayed: Check the LAN connection status.
- When D is displayed: Check the IP address. If you set
TCP/IP like Terminal > In/Out -> TCP/IP -> DHCP Not Use, the
current IP address appears. If you use DHCP, the actual
address received from the DHCP server appears. If the
IP address is set correctly, check the port number. HON-FIN4000xxK-10K

The administrator - HON-FIN4000xxK-10K allows the administrator to give

mode cannot be access rights so only the administrator can enter the
Administrator entered because of menu.
losing the - When you have no choice but to enter the administrator
connection administrator menu, you can be granted an administrator password
password or after following the predefined procedure.
resignation. (Contact with the installation agency.)

53
6.3 Usage summary
※ It provides the mainly used functions.
※ button: Used to select the desired function.

Function Method for setting

(Sequentially perform the following items.)
Initial administrator
Enter ID Enter password Enter password again
registration

Select Screen, Sound ( ) icon Select Date, Time ( ) icon

Date & time setting
Enter date Enter time

Select User ( ) icon Select Enroll ( ) icon Enter ID

User registration
Select General or Administrator in Level Enter fingerprint or PIN

Select User ( ) icon Select Edit ( ) icon Enter ID or

User password
fingerprint Select PIN Enter the desired password Enter it
modification
again

Select User ( ) icon Select Edit ( ) icon Enter ID or

User fingerprint
fingerprint Select Fingerprint Enter the fingerprint of the user
modification
Enter it again

User authorization Select User ( ) icon Select Enroll ( ) icon Enter ID or

method fingerprint Select Operation Mode Select an authorization
modification method

Select User ( ) icon Select Delete ( ) icon Enter ID or

User deletion
fingerprint to delete

Select Device ( ) icon Select System ( ) icon Select

All user deletion
Delete User DB Select Delete

Factory Select Device ( ) icon Select System ( ) icon Select

Initialization Factory Default Select Initialize

54
6.4 System Installation
6.4.1 Cable specifications

HON-FIN4000xxK-10K

Type No. Name Color

1 SWIN0 Purple

2 GND Gray

3 SWIN1 Brown
Switch
& 4 GND Gray
Wiegand
5 W-DATA0 Green

6 W-DATA1 White

7 W-GND Black

8 ERX - Yellow

9 ERX + Blue
Network
10 ETX - Orange HON-FIN4000xxK-10K

11 ETX + Pink

12 Relay Normal Close Orange (White String)

Relay 13 Relay Common Green (White String)

14 Relay Normal Open Gray (White String)

15 Power 12V Red

16 Power Ground Black

Power
& 17 RS485 Ground White (Black String)
RS485
18 RS485 + Blue (White String)

19 RS485 - Yellow (Black String)

55
6.4.2 Installing the bracket

1. Fix the bracket to the place where HON-

FIN4000xxK-10K is to be installed using the fixing
screws.

If the installation place is on concrete, drill holes, insert knife

blocks into the holes, and fix them by using fixing screws.

2. Install HON-FIN4000xxK-10K on the bracket.

3. Fix HON-FIN4000xxK-10K and the wall mount

bracket by rotating the star-shape screw by the
hexagonal wrench.

The extension bracket (Option) is provided for wiring aid

according to the installation environment. Remove the basic
bracket on the body for use of this bracket

56
6.4.3 Connecting Power & RS-485

HON-FIN4000xxK-10K
※RS-485 can be used as an option to connect to the PC.

For power supply, use a product of DC 12V (± 10%) and minimum 500mA.
To share the power adapter with another device, the required current sum of terminal (500mA)
and another device must not exceed the current capacity.

6.4.6 Connecting Network

HON-FIN4000xxK-10K

HON-FIN4000xxK-10K

57
6.4.7 Connecting to a Controller

7 Wiegand IN
6 Ground
D1
5
D0

4 Output (Optional)
3
Ground
Green LED
2
Ground
1 Red LED

HON-FIN4000xxK-10K Honeywell Controller

58
6.4.8 Electrical specifications

Type Name Min. Typ. Max. Notes

Power Voltage (V) 10.8 12 13.2 Use regulated DC power
adaptor only

Current (mA) - 250

Switch VIH (V) - TBD -

Input
VIL (V) - TBD

Pull-up - 4.7k - The input ports are

resistance (Ω ) pulled up with 4.7k
resistors

Relay Switching - - 1 30V DC

capacity (A) 0.3 125V AC

Switching - - 30W DC
power 37.5VA AC
(resistive)

Switching - - 110 DC
voltage (V) 125 AC

HON-FIN4000xxK-10K

59
6.5 Specifications

Item Specification

CPU 533MHz DSP

Fingerprint sensor 500dpi optical sensor

User capacity 5000 users (10,000 Templates)

Log capacity 50,000 events

Operation mode Fingerprint, Password, Fingerprint + Password, Card

I/O 2 TTL Inputs / 1 Relay Output

Wiegand Out 1 Port (Customizable)

LCD 128 x 64 Backlight LCD (Monochrome)

Keypad 3x4 keypad, 3 navigation keys

IP rate IP65 Class

Operation Temperature -20℃ ~50℃

Rated Voltage DC 12V (Min. 500mA and above)

125kHz EM4100 Card (HON-FIN4000EMK-10K)

Supportable Cards 13.56MHz Mifare Card (HON-FIN4000MIK-10K)

Size 60 x 185 x 40 mm (Width x Height x Depth)

Certified CE, FCC, RoHS

60
Mechanical Specifications

HON-FIN4000xxK-10K

61
6.6 FCC Notice

This equipment has been tested and found to comply with the limits
for a Class B digital device, pursuant to part 15 of the FCC Rules.
These limits are designed to provide reasonable protection against
harmful interference in a residential installation. This equipment
generates, uses and can radiate radio frequency energy and, if not
installed and used in accordance with the instructions, may cause
harmful interference to radio communications. However, there is no
guarantee that interference will not occur in a particular installation.
If this equipment does cause harmful interference to radio or
television reception, which can be determined by turning the
equipment off and on, the user is encouraged to try to correct the
interference by one or more of the following measures: ·

Reorient or relocate the receiving antenna.

Increase the separation between the equipment and receiver.
Connect the equipment into an outlet on a circuit different from that
to which the receiver is connected.
Consult the dealer or an experienced radio/TV technician for help.

Modifications not expressly approved by the manufacturer could

void the user's authority to operate the equipment under FCC rules.

62
 HONEYWELL

Honeywell Security Asia Pacific

35F Tower A, City Center, 100 Zun Yi Road, Shanghai 200051, China
TEL +86 21 22196888
FAX +86 21 62370740
http://www.security.honeywell.com/
© 2012 Honeywell International Inc. All rights reserved.