NATIONAL AEROSPACE STANDARD

© COPYRIGHT 2013 AEROSPACE INDUSTRIES ASSOCIATION OF AMERICA, INC. ALL RIGHTS RESERVED

FED. SUPPLY CLASS

LENGTH ± .015 5306
GRIP±.010 /5/ (T)
DOVETAIL SLOT RECESS MAX 2 INCOMPLETE
AEROSPACE INDUSTRIES ASSOCIATION OF AMERICA, INC

PER NASM33750 /8/ THREADS

OFFSET CRUCIFORM END SHALL BE FLAT
RECESS PER NASM14191 /8/ K (U) AND CHAMFERED.
R .030 CHAMFER "(U)" PLUS
.015
/10/ M INCOMPLETE THREADS
NOT TO EXCEED TWO
~ ~ PITCHES.
100°
(ØE)
±1°
ARLINGTON, VA 22209
1000 WILSON BLVD.

ØD DRILL ØP WHEN SPECIFIED.

ØC CSK OPTIONAL. /10/

(L) (ØW) J
THREADS PER AS8879.
(H) MAX MAJOR DIA SHALL BE
.020 .001 BELOW MIN SHANK DIA.
HEAD MARKING PER
NAS1347, TYPE IV .010

ØA ØB
--`,``,,`,`,,```,``````,`,,,`,`-`-`,,`,,`,`,,`---

CURVED EDGE OPTIONAL

ENLARGED VIEW OF HEAD

TABLE I – DIMENSIONS AND STRENGTH VALUES

BASIC THREAD ØA ØB ØC ØD (ØE) (H) J K (L) M ØP (T)
PRODUCT AND SHALL BECOME EFFECTIVE NO LATER THAN SIX MONTHS FROM THE LAST

PART /14/ MIN GAGE /11/ /4/ DEPTH GAGE /4/ /10/ /10/
THIS DRAWING SUPERSEDES ALL ANTECEDENT STANDARD DRAWINGS FOR THE SAME

NUMBER CIRCLE OFFSET DOVETAIL PROTRU- ±.010 +.010

REVISION DATE: NOVEMBER 22, 2013

/6/ CRUCIFORM SLOT SION –.000
/3/ /4/ /6/
.337 .2832 .1635 .078 .053 .0223
NAS2832 .1640-32 UNJC-3A .280 .265 .063 .100 – – .323
.329 .2830 .1625 .068 .050 .0197
.385 .3272 .1895 .090 .045 .0239
NAS2833 .1900-32 UNJF-3A .328 .305 .080 .110 .164 .070 .323
.377 .3270 .1885 .080 .042 .0212
.507 .4320 .2495 .118 .054 .0310
NAS2834 .2500-28 UNJF-3A .449 .422 .106 .134 .170 .076 .370
.498 .4318 .2485 .108 .051 .0282
.635 .5451 .3120 .122 .064 .0371
NAS2835 .3125-24 UNJF-3A .577 .490 .133 .160 .182 .076 .438
.625 .5449 .3110 .112 .061 .0342
.762 .6582 .3745 .145 .088 .0429
NAS2836 .3750-24 UNJF-3A .704 .639 .160 .198 .183 .106 .454
.751 .6580 .3735 .135 .084 .0398
.890 .7784 .4370 .169 .100 .0461
NAS2837 .4375-20 UNJF-3A .832 .715 .188 .224 .199 .106 .528
.879 .7782 .4360 .159 .097 .0429
ISSUE DATE: AUGUST 1980

1.017 .8902 .4995 .193 .105 .0523

NAS2838 .5000-20 UNJF-3A .959 .766 .215 .256 .198 .106 .528
1.005 .8900 .4985 .183 .101 .0490
1.145 1.0028 .5615 .217 .118 .0587
NAS2839 .5625-18 UNJF-3A 1.087 .877 .242 .300 .207 .141 .594
1.132 1.0026 .5605 .207 .114 .0552
REVISION DATE.

1.272 1.1124 .6240 .241 .141 .0659

NAS2840 .6250-18 UNJF-3A 1.214 1.020 .270 .344 .207 .141 .626
1.258 1.1122 .6230 .231 .137 .0623

4 COMPLETELY REVISED

THIRD CUSTODIAN REVISION

ANGLE
PROJECTION NATIONAL AEROSPACE STANDARDS COMMITTEE 4
PROCUREMENT TITLE CLASSIFICATION
FORM 09-01

SPECIFICATION PART STANDARD

4
BOLT, 100° FLAT HEAD, OFFSET CRUCIFORM NAS2832 THRU NAS2840
NOTED AND DOVETAIL SLOT, 180 KSI SHEET 1 OF 6

USE OF OR RELIANCE UPON THIS DOCUMENT OR ANY NATIONAL AEROSPACE STANDARD IS ENTIRELY VOLUNTARY. AIA DOES NOT QUALIFY SUPPLIERS OR CERTIFY
Copyright Aerospace Industries Association of America Inc.
CONFORMANCE OF ITEMS PRODUCED UNDER NATIONAL AEROSPACE STANDARDS. AIA MAKES NO REPRESENTATION OR CLAIM RESPECTING (1) THE SUITABILITY OF
Provided by IHS under license with AIA/NAS Licensee=EMBRAER/1829800100
ITEMS without
No reproduction or networking permitted FOR ANY PARTICULAR
license from IHS APPLICATION OR (2) THE EXISTENCE OF OR APPLICABILITY THERETO
Not for Resale, OF PATENT
11/25/2013 OR TRADEMARKS RIGHTS.
03:51:42 MST
 NATIONAL AEROSPACE STANDARD
© COPYRIGHT 2013 AEROSPACE INDUSTRIES ASSOCIATION OF AMERICA, INC. ALL RIGHTS RESERVED

TABLE I – DIMENSIONS AND STRENGTH VALUES (CONTINUED)

BASIC (U) (ØW) RECESS NUMBER DOUBLE SHEAR TENSILE FIM VALUE RECESS FATIGUE LOADING, LBF
PART /3/ STRENGTH STRENGTH TORQUE ALLOY STEEL TITANIUM
NUMBER LBF MIN LBF MIN IN-LBF MIN AND CRES /18/ /19/
OFFSET DOVETAIL /12/ Y Z /8/ HIGH LOW HIGH LOW
AEROSPACE INDUSTRIES ASSOCIATION OF AMERICA, INC

CRUCIFORM SLOT /1/ /2/ TENSION TENSION TENSION TENSION

LOAD LOAD LOAD LOAD
.215
NAS2832 .016 8 2 4,600 2,520 .005 .0040 42 950 95 840 84
.205
.248
NAS2833 .016 10 3 6,100 3,600 .005 .0040 58 1,350 135 1,200 120
.238
.325
NAS2834 .018 1/4 4 10,600 6,550 .006 .0030 125 2,460 246 2,180 218
.315
.357
NAS2835 .021 5/16 5 16,600 10,400 .007 .0030 250 3,900 390 3,460 346
ARLINGTON, VA 22209

.347
1000 WILSON BLVD.

.427
NAS2836 .021 3/8 6 23,900 15,800 .009 .0025 430 5,930 593 5,260 526
.417
.498
NAS2837 .025 7/16 7 32,500 21,400 .009 .0025 925 8,030 803 7,130 713
.488
.568
NAS2838 .025 1/2 8 42,400 28,800 .010 .0020 1,210 10,800 1,080 9,590 959
.558
.638
NAS2839 .028 9/16 9 53,700 36,500 .010 .0020 1,760 13,700 1,370 12,200 1,220
.628
.708
NAS2840 .028 5/8 10 66,300 46,000 .010 .0020 2,460 17,300 1,730 15,300 1,530
.698

MATERIAL:

ALLOY STEEL - 4140 (UNS G41400) PER MIL-S-5626 AMS6382, 4340 (UNS G43406) PER MIL-S-5000
AMS6415 OR AMS6484, OR 8740 (UNS G87400) PER MIL-S-6049 AMS6322, AMS6325

--`,``,,`,`,,```,``````,`,,,`,`-`-`,,`,,`,`,,`---
OR AMS6327.
CRES - A286 (UNS S66286) CONFORMING TO THE CHEMISTRY OF AMS5731, AMS5732,
AMS5737 OR AMS5853 EXCEPT HEAT TREAT TO 180 KSI MIN.
PRODUCT AND SHALL BECOME EFFECTIVE NO LATER THAN SIX MONTHS FROM THE LAST

TITANIUM ALLOY - 6AL-6V-2SN (UNS R56620) PER AMS4971.

THIS DRAWING SUPERSEDES ALL ANTECEDENT STANDARD DRAWINGS FOR THE SAME

HEAT TREATMENT:

DEVELOP BASIC MATERIAL PROPERTIES AS FOLLOWS, WITH CONTROLS PER AMS2759 FOR ALLOY STEEL
AND CRES AND AMS-H-81200 OR AMS2801 FOR TITANIUM.

ALLOY STEEL: 180-200 KSI Ftu. 39 - 43HRC.

CRES: 180-210 KSI Ftu
TITANIUM ALLOY: 180 KSI Ftu MIN

FINISH: ALLOY STEEL - CADMIUM PLATE PER AMS-QQ-P-416, TYPE II, CLASS 2. BOLTS ARE NOT TO BE
PICKLED. IMMEDIATELY AFTER PLATING (WITHIN 1 HOUR), BAKE AT
375 ± 25 °F FOR A MINIMUM OF 23 HOURS.
CRES - CLEAN AND PASSIVATE PER AMS2700, METHOD 1, CLASS 4. OPTIONAL ALUMINUM COAT
PER NAS4006 DESIGNATED BY CODE “P”. EXCEPT ON PARTS CODED “N”, INCLUDE A
HALOGEN FREE CETYL ALCOHOL LUBRICANT ON ALL CRES BOLTS BOTH WITH AND
WITHOUT THE NAS4006 COATING. APPLY THE LUBRICANT ON “P” CODE BOLTS ONLY
AFTER THE NAS4006 COATING IS APPLIED.
REVISION DATE.

TITANIUM ALLOY - NONE. OPTIONAL ALUMINUM COAT PER NAS4006 DESIGNATED BY CODE “P”. EXCEPT ON
PARTS CODED “N”, INCLUDE A HALOGEN FREE CETYL ALCOHOL LUBRICANT ON ALL
TITANIUM ALLOY BOLTS BOTH WITH AND WITHOUT THE NAS4006 COATING. APPLY THE
LUBRICANT ON “P” CODE BOLTS ONLY AFTER THE NAS4006 COATING IS APPLIED.

REVISION

4
FORM 09-01

4 COMPLETELY REVISED NAS2832 THRU NAS2840

SHEET 2

USE OF OR RELIANCE UPON THIS DOCUMENT OR ANY NATIONAL AEROSPACE STANDARD IS ENTIRELY VOLUNTARY. AIA DOES NOT QUALIFY SUPPLIERS OR CERTIFY
Copyright Aerospace Industries Association of America Inc.
CONFORMANCE OF ITEMS PRODUCED UNDER NATIONAL AEROSPACE STANDARDS. AIA MAKES NO REPRESENTATION OR CLAIM RESPECTING (1) THE SUITABILITY OF
Provided by IHS under license with AIA/NAS Licensee=EMBRAER/1829800100
ITEMS without
No reproduction or networking permitted FOR ANY PARTICULAR
license from IHS APPLICATION OR (2) THE EXISTENCE OF OR APPLICABILITY THERETO
Not for Resale, OF PATENT
11/25/2013 OR TRADEMARKS RIGHTS.
03:51:42 MST
 NATIONAL AEROSPACE STANDARD
© COPYRIGHT 2013 AEROSPACE INDUSTRIES ASSOCIATION OF AMERICA, INC. ALL RIGHTS RESERVED

CODE: ADD “-” BETWEEN BASIC PART NUMBER AND DASH NUMBER FOR BOLT, ALLOY STEEL, UNDRILLED.
ADD “C” IN LIEU OF DASH TO DESIGNATE CORROSION RESISTANT STEEL.
ADD “D” TO DASH NUMBER FOR DRILLED SHANK.
ADD “H” TO DASH NUMBER FOR DOVETAIL SLOT RECESS.
AEROSPACE INDUSTRIES ASSOCIATION OF AMERICA, INC

ADD “N” TO DASH NUMBER FOR BOLTS WITHOUT CETYL ALCOHOL LUBRICANT.
ADD “P” TO DASH NUMBER FOR BOLTS WITH ALUMINUM COAT.
ADD “T” IN LIEU OF DASH TO DESIGNATE TITANIUM ALLOY.
ADD “T” TO DASH NUMBER FOR OFFSET CRUCIFORM RECESS.
FOR “X” AND “Y” CODES, SEE SHEET 6.
AFTER THE DASH NUMBER, WHERE MORE THAN ONE CODE LETTER IS USED IN PART NUMBER, ARRANGE
LETTERS ALPHABETICALLY.

EXAMPLE OF PART NUMBER:

ARLINGTON, VA 22209
1000 WILSON BLVD.

NAS2838-10T = BOLT, .5000-20 THREAD, .625 GRIP, ALLOY STEEL, CADMIUM PLATE, UNDRILLED,
OFFSET CRUCIFORM RECESS.
NAS2838T10H = BOLT, .5000-20 THREAD, .625 GRIP, TITANIUM ALLOY, UNDRILLED, DOVETAIL SLOT
RECESS, INCLUDES A CETYL ALCOHOL LUBRICANT.
NAS2838T10HN = BOLT, .5000-20 THREAD, .625 GRIP, TITANIUM ALLOY, UNDRILLED, DOVETAIL SLOT
RECESS, WITHOUT A CETYL ALCOHOL LUBRICANT.
NAS2838C10DH = BOLT, .5000-20 THREAD, .625 GRIP, CRES, DRILLED SHANK, DOVETAIL SLOT RECESS,
INCLUDES A CETYL ALCOHOL LUBRICANT.
NAS2838C10DHN = BOLT, .5000-20 THREAD, .625 GRIP, CRES, DRILLED SHANK, DOVETAIL SLOT RECESS,
WITHOUT A CETYL ALCOHOL LUBRICANT.
NAS2838C10PT = BOLT, .5000-20 THREAD, .625 GRIP, CRES, UNDRILLED, ALUMINUM COATED, OFFSET
CRUCIFORM RECESS, INCLUDES A CETYL ALCOHOL LUBRICANT.
NAS2838C10NPT = BOLT, .5000-20 THREAD, .625 GRIP, CRES, UNDRILLED, ALUMINUM COATED, OFFSET
CRUCIFORM RECESS, WITHOUT A CETYL ALCOHOL LUBRICANT.
NAS2838T10DHP = BOLT, .5000-20 THREAD, .625 GRIP, TITANIUM ALLOY, DRILLED SHANK, DOVETAIL
SLOT RECESS, ALUMINUM COATED, INCLUDES A CETYL ALCOHOL LUBRICANT.
NAS2838T10DHNP = BOLT, .5000-20 THREAD, .625 GRIP, TITANIUM ALLOY, DRILLED SHANK, DOVETAIL
SLOT RECESS, ALUMINUM COATED, WITHOUT A CETYL ALCOHOL LUBRICANT.
PRODUCT AND SHALL BECOME EFFECTIVE NO LATER THAN SIX MONTHS FROM THE LAST
THIS DRAWING SUPERSEDES ALL ANTECEDENT STANDARD DRAWINGS FOR THE SAME

NOTES:

--`,``,,`,`,,```,``````,`,,,`,`-`-`,,`,,`,`,,`---
/1/ CONCENTRICITY: “ØD” AND THREAD PITCH DIAMETER WITHIN “Y” VALUES FIM. CONICAL SURFACE OF
HEAD AND “ØD” WITHIN .005 VALUES FIM. RECESS TO “ØD” WITHIN .016 FIM THRU Ø.2500 SIZE,
WITHIN .024 FIM ABOVE Ø.2500.

/2/ SHANK STRAIGHTNESS: WITHIN “Z” VALUES FIM PER INCH OF LENGTH.

/3/ OFFSET CRUCIFORM RECESS GAGING IN ACCORDANCE WITH NASM14191.

/4/ DOVETAIL SLOT RECESS GAGING IN ACCORDANCE WITH NASM33750.

/5/ GRIP LENGTH: FROM THE TOP OF HEAD TO END OF FULL CYLINDRICAL PORTION OF SHANK.

/6/ REFER TO NAS518 AND NAS519 FOR FLUSHNESS GAGING DETAILS.

(7) BOLT SHALL BE FREE FROM BURRS AND SHARP EDGES.

REVISION DATE.

/8/ RECESSES SHALL WITHSTAND MINIMUM TORQUE VALUES LISTED WITHOUT DAMAGE TO RECESSES OR
DRIVERS PER NASM33750 OR NASM14191.

(9) BEARING SURFACE SQUARENESS: WITHIN .003 FIM OF “ØD”.

REVISION

4
FORM 09-01

4 COMPLETELY REVISED NAS2832 THRU NAS2840

SHEET 3

USE OF OR RELIANCE UPON THIS DOCUMENT OR ANY NATIONAL AEROSPACE STANDARD IS ENTIRELY VOLUNTARY. AIA DOES NOT QUALIFY SUPPLIERS OR CERTIFY
Copyright Aerospace Industries Association of America Inc.
CONFORMANCE OF ITEMS PRODUCED UNDER NATIONAL AEROSPACE STANDARDS. AIA MAKES NO REPRESENTATION OR CLAIM RESPECTING (1) THE SUITABILITY OF
Provided by IHS under license with AIA/NAS Licensee=EMBRAER/1829800100
ITEMS without
No reproduction or networking permitted FOR ANY PARTICULAR
license from IHS APPLICATION OR (2) THE EXISTENCE OF OR APPLICABILITY THERETO
Not for Resale, OF PATENT
11/25/2013 OR TRADEMARKS RIGHTS.
03:51:42 MST
 NATIONAL AEROSPACE STANDARD
© COPYRIGHT 2013 AEROSPACE INDUSTRIES ASSOCIATION OF AMERICA, INC. ALL RIGHTS RESERVED

/10/ COTTER PIN HOLE CENTERLINE WITHIN .010 AND PERPENDICULAR WITHIN 2° OF BOLT CENTERLINE.

/11/ “ØD AFTER PLATING OR COATING” DIMENSION SHALL APPLY FOR BARE TITANIUM ALLOY AND CRES BOLTS.
AEROSPACE INDUSTRIES ASSOCIATION OF AMERICA, INC

(12) THE TENSILE STRESS AREA USED FOR THE CALCULATION OF THE MINIMUM TENSILE STRENGTH VALUES
WERE TAKEN FROM FED-STD-H28.

(13) SURFACE ROUGHNESS: SEE PROCUREMENT SPECIFICATION.

/14/ THE HEAD TO SHANK FILLET AND THE THREADS ARE TO BE ROLLED AFTER HEAT TREAT.

(15) A MAGNETIC PARTICLE INSPECTION SHALL BE PERFORMED BY THE SUPPLIER OF ALL ALLOY STEEL OFFSET
CRUCIFORM AND FLUORESCENT PENETRANT INSPECTION OF ALL TITANIUM OFFSET CRUCIFORM RECESSES
ARLINGTON, VA 22209

(ALL SURFACES INSIDE RECESS) FOR EACH BOLT IN EACH LOT. ANY INDICATION IN ANY BOLT
1000 WILSON BLVD.

SUBSEQUENTLY PROVEN BY SECTIONING TO BE CRACKED SHALL BE CAUSE FOR REJECTION OF THE ENTIRE
LOT.

(16) SUBSEQUENT TO CADMIUM PLATING, FOR EACH LOT OF BOLTS, 4 OR MORE BOLTS SHALL BE INSTALLED
AND LOADED TO 80% OF RATED TENSILE LOAD FOR A MINIMUM OF 72 HOURS. AT THE END OF THIS TIME,
IF ANY CRACKS OR FAILURES HAVE OCCURRED, THE ENTIRE LOT SHALL BE REJECTED.

(17) THE FULL LENGTH OF THE SHANK AND THREADS SHALL BE PROTECTED FROM ABRASIONS AND CHAFING
DURING HANDLING, TRANSPORTATION AND STORAGE. INCLUDE TITANIUM PARTS Ø.190 AND ABOVE; ON
OTHER MATERIAL INCLUDE Ø.250 AND ABOVE.

/18/ HIGH TENSILE LOAD = .375 x Ftu

/19/ HIGH TENSILE LOAD = .333 x Ftu

(20) DIMENSIONS IN INCHES AND APPLY AFTER FINISH AND PRIOR TO THE APPLICATION OF LUBRICATION
UNLESS OTHERWISE SPECIFIED.
PRODUCT AND SHALL BECOME EFFECTIVE NO LATER THAN SIX MONTHS FROM THE LAST

(21) THIS STANDARD TAKES PRECEDENCE OVER DOCUMENTS REFERENCED HEREIN.

THIS DRAWING SUPERSEDES ALL ANTECEDENT STANDARD DRAWINGS FOR THE SAME

(22) UNLESS OTHERWISE SPECIFIED, PART INVENTORY MANUFACTURED TO PREVIOUS REVISIONS OF THE
APPLICABLE DRAWING OR SPECIFICATION MAY BE PROCURED AND USED UNTIL

--`,``,,`,`,,```,``````,`,,,`,`-`-`,,`,,`,`,,`---
STOCK IS DEPLETED.

(23) UNLESS OTHERWISE SPECIFIED HEREIN, REFERENCED DOCUMENTS SHALL BE THE ISSUE IN EFFECT ON
DATE OF MANUFACTURE. HOWEVER, EXISTING MATERIAL INVENTORY CERTIFIED TO A PREVIOUS REVISION
OF THE APPLICABLE MATERIAL SPECIFICATION(S) IS ACCEPTABLE FOR USE UNTIL DEPLETION.

(24) DIMENSIONING AND TOLERANCING PER ANSI Y14.5M-1982.

PROCUREMENT SPECIFICATION:

MIL-B-87114 NAS9925 EXCEPT AS NOTED. TENSILE STRENGTH, RECESS TORQUE VALUES, AND DOUBLE
SHEAR STRENGTH VALUES AS TABULATED HEREIN. FLUSHNESS GAGING DETAILS AND .1640-32 BOLT
REQUIREMENTS AS NOTED HEREIN.
REVISION DATE.

REVISION

4
FORM 09-01

4 COMPLETELY REVISED NAS2832 THRU NAS2840

SHEET 4

USE OF OR RELIANCE UPON THIS DOCUMENT OR ANY NATIONAL AEROSPACE STANDARD IS ENTIRELY VOLUNTARY. AIA DOES NOT QUALIFY SUPPLIERS OR CERTIFY
Copyright Aerospace Industries Association of America Inc.
CONFORMANCE OF ITEMS PRODUCED UNDER NATIONAL AEROSPACE STANDARDS. AIA MAKES NO REPRESENTATION OR CLAIM RESPECTING (1) THE SUITABILITY OF
Provided by IHS under license with AIA/NAS Licensee=EMBRAER/1829800100
ITEMS without
No reproduction or networking permitted FOR ANY PARTICULAR
license from IHS APPLICATION OR (2) THE EXISTENCE OF OR APPLICABILITY THERETO
Not for Resale, OF PATENT
11/25/2013 OR TRADEMARKS RIGHTS.
03:51:42 MST
 NATIONAL AEROSPACE STANDARD
© COPYRIGHT 2013 AEROSPACE INDUSTRIES ASSOCIATION OF AMERICA, INC. ALL RIGHTS RESERVED

TABLE II – GRIP AND NOMINAL LENGTH

GRIP GRIP LENGTH ± .015 (SEE NOTE BELOW)
DASH ±.010 BASIC PART NUMBER AND THREAD SIZE
NUMBER /5/ NAS2832 NAS2833 NAS2834 NAS2835 NAS2836 NAS2837 NAS2838 NAS2839 NAS2840
.1640-32 .1900-32 .2500-28 .3125-24 .3750-24 .4375-20 .5000-20 .5625-18 .6250-18
AEROSPACE INDUSTRIES ASSOCIATION OF AMERICA, INC

2 .125 .448 .448

3 .188 .511 .511 .558 .626 .642
4 .250 .573 .573 .620 .688 .704 .778 .778
5 .312 .635 .635 .682 .750 .766 .840 .840 .906 .938
6 .375 .698 .698 .745 .813 .829 .903 .903 .969 1.001
7 .438 .761 .761 .808 .876 .892 .966 .966 1.032 1.064
8 .500 .823 .823 .870 .938 .954 1.028 1.028 1.094 1.126
9 .562 .885 .885 .932 1.000 1.016 1.090 1.090 1.156 1.188
10 .625 .948 .948 .995 1.063 1.079 1.153 1.153 1.219 1.251
11 .688 1.011 1.011 1.058 1.126 1.142 1.216 1.216 1.282 1.314
12 .750 1.073 1.073 1.120 1.188 1.204 1.278 1.278 1.344 1.376
ARLINGTON, VA 22209

13 .812 1.135 1.135 1.182 1.250 1.266 1.340 1.340 1.406 1.438
1000 WILSON BLVD.

14 .875 1.198 1.198 1.245 1.313 1.329 1.403 1.403 1.469 1.501
15 .938 1.261 1.261 1.308 1.376 1.392 1.466 1.466 1.532 1.564
16 1.000 1.323 1.323 1.370 1.438 1.454 1.528 1.528 1.594 1.626
17 1.062 1.385 1.385 1.432 1.500 1.516 1.590 1.590 1.656 1.688
18 1.125 1.448 1.448 1.495 1.563 1.579 1.653 1.653 1.719 1.751
19 1.188 1.511 1.511 1.558 1.626 1.642 1.716 1.716 1.782 1.814
20 1.250 1.573 1.573 1.620 1.688 1.704 1.778 1.778 1.844 1.876
21 1.312 1.635 1.635 1.682 1.750 1.766 1.840 1.840 1.906 1.938
22 1.375 1.698 1.698 1.745 1.813 1.829 1.903 1.903 1.969 2.001
--`,``,,`,`,,```,``````,`,,,`,`-`-`,,`,,`,`,,`---

23 1.438 1.761 1.761 1.808 1.876 1.892 1.966 1.966 2.032 2.064
24 1.500 1.823 1.823 1.870 1.938 1.954 2.028 2.028 2.094 2.126
25 1.562 1.885 1.885 1.932 2.000 2.016 2.090 2.090 2.156 2.188
26 1.625 1.948 1.948 1.995 2.063 2.079 2.153 2.153 2.219 2.251
27 1.688 2.011 2.011 2.058 2.126 2.142 2.216 2.216 2.282 2.314
28 1.750 2.073 2.073 2.120 2.188 2.204 2.278 2.278 2.344 2.376
29 1.812 2.135 2.135 2.182 2.250 2.266 2.340 2.340 2.406 2.438
30 1.875 2.198 2.198 2.245 2.313 2.329 2.403 2.403 2.469 2.501
31 1.938 2.261 2.261 2.308 2.376 2.392 2.466 2.466 2.532 2.564
32 2.000 2.323 2.323 2.370 2.438 2.454 2.528 2.528 2.594 2.626
34 2.125 2.448 2.448 2.495 2.563 2.579 2.653 2.653 2.719 2.751
36 2.250 2.573 2.573 2.620 2.688 2.704 2.778 2.778 2.844 2.876
38 2.375 2.698 2.698 2.745 2.813 2.829 2.903 2.903 2.969 3.001
40 2.500 2.823 2.823 2.870 2.938 2.954 3.028 3.028 3.094 3.126
PRODUCT AND SHALL BECOME EFFECTIVE NO LATER THAN SIX MONTHS FROM THE LAST

42 2.625 2.948 2.948 2.995 3.063 3.079 3.153 3.153 3.219 3.251
THIS DRAWING SUPERSEDES ALL ANTECEDENT STANDARD DRAWINGS FOR THE SAME

44 2.750 3.073 3.073 3.120 3.188 3.204 3.278 3.278 3.344 3.376
46 2.875 3.198 3.198 3.245 3.313 3.329 3.403 3.403 3.469 3.501
48 3.000 3.323 3.323 3.370 3.438 3.454 3.528 3.528 3.594 3.626
50 3.125 3.448 3.448 3.495 3.563 3.579 3.653 3.653 3.719 3.751
52 3.250 3.573 3.573 3.620 3.688 3.704 3.778 3.778 3.844 3.876
54 3.375 3.698 3.698 3.745 3.813 3.829 3.903 3.903 3.969 4.001
56 3.500 3.823 3.823 3.870 3.938 3.954 4.028 4.028 4.094 4.126
58 3.625 3.948 3.948 3.995 4.063 4.079 4.153 4.153 4.219 4.251
60 3.750 4.073 4.073 4.120 4.188 4.204 4.278 4.278 4.344 4.376
62 3.875 4.198 4.198 4.245 4.313 4.329 4.403 4.403 4.469 4.501
64 4.000 4.323 4.323 4.370 4.438 4.454 4.528 4.528 4.594 4.626
66 4.125 4.448 4.448 4.495 4.563 4.579 4.653 4.653 4.719 4.751
68 4.250 4.573 4.573 4.620 4.688 4.704 4.778 4.778 4.844 4.876
70 4.375 4.698 4.698 4.745 4.813 4.829 4.903 4.903 4.969 5.001
72 4.500 4.823 4.823 4.870 4.938 4.954 5.028 5.028 5.094 5.126
74 4.625 4.948 4.948 4.995 5.063 5.079 5.153 5.153 5.219 5.251
76 4.750 5.073 5.073 5.120 5.188 5.204 5.278 5.278 5.344 5.376
78 4.875 5.198 5.198 5.245 5.313 5.329 5.403 5.403 5.469 5.501
80 5.000 5.323 5.323 5.370 5.438 5.454 5.528 5.528 5.594 5.626
82 5.125 5.448 5.448 5.495 5.563 5.579 5.653 5.653 5.719 5.751
84 5.250 5.573 5.573 5.620 5.688 5.704 5.778 5.778 5.844 5.876
86 5.375 5.698 5.698 5.745 5.813 5.829 5.903 5.903 5.969 6.001
REVISION DATE.

88 5.500 5.823 5.823 5.870 5.938 5.954 6.028 6.028 6.094 6.126
90 5.625 5.948 5.948 5.995 6.063 6.079 6.153 6.153 6.219 6.251
92 5.750 6.073 6.073 6.120 6.188 6.204 6.278 6.278 6.344 6.376
94 5.875 6.198 6.198 6.245 6.313 6.329 6.403 6.403 6.469 6.501
96 6.000 6.323 6.323 6.370 6.438 6.454 6.528 6.528 6.594 6.626
INTERMEDIATE AND LONGER LENGTHS MAY BE SPECIFIED BY USE OF WHOLE GRIP DASH NUMBERS ONLY.
NOMINAL GRIP DIMENSION EQUALS GRIP DASH NUMBER TIMES .0625 (ROUNDED TO 3 DECIMAL PLACES).
NOMINAL LENGTH EQUALS NOMINAL GRIP PLUS “T” (SEE TABLE I).
REVISION

4
FORM 09-01

4 COMPLETELY REVISED NAS2832 THRU NAS2840

SHEET 5

USE OF OR RELIANCE UPON THIS DOCUMENT OR ANY NATIONAL AEROSPACE STANDARD IS ENTIRELY VOLUNTARY. AIA DOES NOT QUALIFY SUPPLIERS OR CERTIFY
Copyright Aerospace Industries Association of America Inc.
CONFORMANCE OF ITEMS PRODUCED UNDER NATIONAL AEROSPACE STANDARDS. AIA MAKES NO REPRESENTATION OR CLAIM RESPECTING (1) THE SUITABILITY OF
Provided by IHS under license with AIA/NAS Licensee=EMBRAER/1829800100
ITEMS without
No reproduction or networking permitted FOR ANY PARTICULAR
license from IHS APPLICATION OR (2) THE EXISTENCE OF OR APPLICABILITY THERETO
Not for Resale, OF PATENT
11/25/2013 OR TRADEMARKS RIGHTS.
03:51:42 MST
 NATIONAL AEROSPACE STANDARD
© COPYRIGHT 2013 AEROSPACE INDUSTRIES ASSOCIATION OF AMERICA, INC. ALL RIGHTS RESERVED

RESTRICTED USAGE: FOR REPAIR WORK ONLY

.0156 AND .0312 OVERSIZE SHANK FOR REPLACEMENT OF BOLTS SHOWN ON SHEET 1.
AEROSPACE INDUSTRIES ASSOCIATION OF AMERICA, INC

HEAD MARKING: SAME AS SHOWN ON SHEET 1 PLUS IDENTIFICATION FOR OVERSIZE, AS APPLICABLE, TO
BE INCLUDED IN SECOND SECTOR. IDENTIFY .0156 OVERSIZE BY “X”. IDENTIFY .0312 OVERSIZE BY “Y”.

HEAD HEIGHT DIMENSIONS “(H)” ARE REDUCED WITH OVERSIZE SHANKS.

REDUCTION IS: .0065 FOR .0156 OVERSIZE BOLTS.
.0130 FOR .0312 OVERSIZE BOLTS.
ARLINGTON, VA 22209
1000 WILSON BLVD.

ØD

MAJOR DIAMETER OF THREADS MAY

CONFORM TO THREAD DIAMETER ON
SHEET 1 OR AS8879 TOLERANCE.
--`,``,,`,`,,```,``````,`,,,`,`-`-`,,`,,`,`,,`---

TABLE III – OVERSIZE PART NUMBERS AND DIMENSIONS

.0156 OVERSIZE .0312 OVERSIZE
PRODUCT AND SHALL BECOME EFFECTIVE NO LATER THAN SIX MONTHS FROM THE LAST

BASIC ØD BASIC ØD
THIS DRAWING SUPERSEDES ALL ANTECEDENT STANDARD DRAWINGS FOR THE SAME

PART PART
NUMBER NUMBER
.2026 .2182
NAS2833-(*)X NAS2833-(*)Y
.2016 .2172
.2651 .2807
NAS2834-(*)X NAS2834-(*)Y
.2641 .2797
.3276 .3432
NAS2835-(*)X NAS2835-(*)Y
.3266 .3422
.3901 .4057
NAS2836-(*)X NAS2836-(*)Y
.3891 .4047
.4526 .4682
NAS2837-(*)X NAS2837-(*)Y
.4516 .4672
.5151 .5307
NAS2838-(*)X NAS2838-(*)Y
.5141 .5297
.5771 .5927
NAS2839-(*)X NAS2839-(*)Y
.5761 .5917
.6396 .6552
NAS2840-(*)X NAS2840-(*)Y
.6386 .6542
* GRIP DASH NUMBER IN .0625 INCREMENTS. SEE SHEET 2 FOR MATERIAL,
REVISION DATE.

RECESS AND FINISH CALLOUTS. FOR NAS2832 OVERSIZE USE NAS2833. SEE
SHEET 1 AND 2 FOR DIMENSIONS NOT SHOWN.

REVISION

4
FORM 09-01

4 COMPLETELY REVISED NAS2832 THRU NAS2840

SHEET 6

USE OF OR RELIANCE UPON THIS DOCUMENT OR ANY NATIONAL AEROSPACE STANDARD IS ENTIRELY VOLUNTARY. AIA DOES NOT QUALIFY SUPPLIERS OR CERTIFY
Copyright Aerospace Industries Association of America Inc.
CONFORMANCE OF ITEMS PRODUCED UNDER NATIONAL AEROSPACE STANDARDS. AIA MAKES NO REPRESENTATION OR CLAIM RESPECTING (1) THE SUITABILITY OF
Provided by IHS under license with AIA/NAS Licensee=EMBRAER/1829800100
ITEMS without
No reproduction or networking permitted FOR ANY PARTICULAR
license from IHS APPLICATION OR (2) THE EXISTENCE OF OR APPLICABILITY THERETO
Not for Resale, OF PATENT
11/25/2013 OR TRADEMARKS RIGHTS.
03:51:42 MST