LED TV

LH60**

AAA AA

a X4 b X4
(M4 X L20) (M4 X L20)
X2
32/43LH60** 49/55LH60**

: Depending on model / Selon le modèle / Dependendo do modelo /

P/No: MFL69275502 (1604-REV02)

www.lg.com Printed in Korea
1 2 3 4

5-A 32/43LH60** 5-B 49/55LH60** 6

a b
 ANTENNA/
CABLE IN

HDMI IN

HDMI IN/ARC

USB IN

LAN

H/P OUT
 LAN

H/P OUT

Satellite IN

OPTICAL DIGITAL
AUDIO OUT
PCMCIA CARD SLOT

: Depending on model / Selon le modèle / Dependendo do modelo /

COMPONENT IN AV IN

VIDEO/Y PB PR L/MONO AUDIO R VIDEO/Y PB PR L/MONO AUDIO R

COMPONENT IN AV IN

VIDEO/Y PB PR L/MONO AUDIO R VIDEO/Y PB PR L/MONO AUDIO R

VIDEO AUDIO VIDEO L/MONO AUDIO R

 1 2

3 4

1 2

3 4

: Depending on model / Selon le modèle / Dependendo do modelo /

0 1 2 A
E

D B

G1 G2
F C

A B C D E F F G1 G2
32LH600B-TB
32LH600D-TB
32LH601D-TC
32LH602D-TD
32LH602U-TD 733 483 170 436 76.3 5.08 4.94
32LH602Z-TD
32LH604D-TB
32LH604U-TB
32LH604Z-TB
32LH600T-TB
32LH601T-TC
733 483 170 436 76.3 5.46 5.32
32LH602T-TD
32LH604T-TB
0 1 2

A B C D E F F G1 G2
43LH600T-TB
43LH601T-TC
43LH602T-TD
43LH600V-TB
974 620 199 571 79.4 9.45 9.25
43LH602V-TD
43LH600Y-TB
43LH602Y-TD
43LH605T-TB
49LH600T-TB
49LH601T-TC
49LH602T-TD
49LH600V-TB
1107 702 216 645 79.4 12.1 11.84
49LH602V-TD
49LH600Y-TB
49LH602Y-TD
49LH605T-TB
55LH600T-TB
55LH601T-TC
55LH602T-TD
55LH600V-TB
1241 775 216 720 63.0 16.6 16.34
55LH602V-TD
55LH600Y-TB
55LH602Y-TD
55LH605T-TB
*MFL69275502*
OWNER’S MANUAL

Safety and Reference

LED TV*
* Disclaimer
LG LED TV applies LCD screen with LED backlights.

Please read this manual carefully before operating your set and
retain it for future reference.

www.lg.com
*MFL69332702* P/NO : MFL69332702 (1604-REV03)
Printed in Korea
India region only. (Below sentence is not applicable for above 1920 X 1080 resolution TV models.)

ATTENTION:
This product is qualified for the BEE Star rating in the ‘Home’ Mode.
The Objectives of Star Labeling Program is designed to promote energy efficient products and practices.
When the television is initially set up, it is designed to meet the BEE Star Labeling requirements while maintaining optimum picture quality.
•  Changes to certain functionalities of this television (TV Guide, Picture/sound etc) may change the power consumption.
•  Depending upon such changed setting (eg., Retail mode), the power consumption may vary which possibly could exceed the stated energy
consumption.
To reset the television to Star rating qualified settings, select ‘Home’ mode from the initial set-up procedure in ‘factory settings’ under the
‘Set-up’ menu.
Safety instructions
Please read these safety precautions carefully before using the product.
WARNING

ENGLISH
Make sure to connect Mains cable to compliant AC mains socket with
Grounded earth pin. (Except for devices which are not grounded on
earth.) Otherwise possibility you may be electrocuted or injured.

Do not place the TV and/or remote control in the following

environments:
•  A location exposed to direct sunlight
Insert power cable plug completely into wall socket otherwise if not
•  An area with high humidity such as a bathroom
secured completely into socket, fire ignition may break out.
•  Near any heat source such as stoves and other devices that
produce heat
•  Near kitchen counters or humidifiers where they can easily be
exposed to steam or oil
•  An area exposed to rain or wind
•  Near containers of water such as vases Ensure the power cord does not come into contact with hot objects
Otherwise, this may result in fire, electric shock, malfunction or product such as a heater. This may cause a fire or an electric shock hazard.
deformation.

Do not place a heavy object, or the product itself, on power cables.

Do not place the product where it might be exposed to dust. This may Otherwise, this may result in fire or electric shock.
cause a fire hazard.

Bend antenna cable between inside and outside building to prevent

Mains Plug is the TV connecting/disconnecting device to AC mains rain from flowing in. This may cause water damaged inside the Product
electric supply. This plug must remain readily attached and operable and could give an electric shock.
when TV is in use.

When mounting TV onto wall make sure to neatly install and isolate
Do not touch the power plug with wet hands. Additionally, if the cord cabling from rear of TV as to not create possibility of electric shock /
pin is wet or covered with dust, dry the power plug completely or wipe fire hazard.
dust off. You may be electrocuted due to excess moisture.

Do not plug too many electrical devices into a single multiple electrical
outlet. Otherwise, this may result in fire due to over-heating.

3
ENGLISH

Do not drop the product or let it fall over when connecting external Do not drop metallic objects such as coins, hair pins, chopsticks or wire
devices. Otherwise, this may result in injury or damage to the product. into the product, or inflammable objects such as paper and matches.
Children must pay particular attention. Electrical shock, fire or injury
can occur. If a foreign object is dropped into the product, unplug the
power cord and contact the service centre.
Des
icca
nt

Keep the anti-moisture packing material or vinyl packing out of the

reach of children. Anti-moisture material is harmful if swallowed. If
swallowed by mistake, force the patient to vomit and visit the nearest
hospital. Additionally, vinyl packing can cause suffocation. Keep it out Do not spray water on the product or scrub with an inflammable
of the reach of children. substance (thinner or benzene). Fire or electric shock accident can
occur.

Do not let your children climb or cling onto the TV.

Otherwise, the TV may fall over, which may cause serious injury. Do not allow any impact, shock or any objects to fall into the unit,
and do not drop anything onto the screen. You may be injured or the
product can be damaged.

Dispose of used batteries carefully to ensure that a small child does not
consume them. Please seek Doctor- Medical Attention immediately if
child consumes batteries. Never touch this product or antenna during a thunder or lighting storm.
You may be electrocuted.

Do not insert any metal objects/conductors (like a metal chopstick/

cutlery/screwdriver) between power cable plug and input Wall Socket Never touch the wall outlet when there is leakage of gas, open the
while it is connected to the input terminal on the wall. Additionally, windows and ventilate. It may cause a fire or a burn by a spark.
do not touch the power cable right after plugging into the wall input
terminal. You may be electrocuted. (Depending on model)

Do not disassemble, repair or modify the product at your own

Do not put or store inflammable substances near the product. There is a discretion. Fire or electric shock accident can occur.
danger of combustion/explosion or fire due to careless handling of the Contact the service centre for check, calibration or repair.
inflammable substances.

4
 Be careful in handling the adapter to prevent any external shocks to it.

ENGLISH
If any of the following occur, unplug the product immediately and
An external shock may cause damage to the adapter.
contact your local service centre.
•  The product has been impacted by shock
•  The product has been damaged
•  Foreign objects have entered the product
•  The product produced smoke or a strange smell
This may result in fire or electric shock. Make sure the power cord is connected securely to the power plug on
the TV. (Depending on model)

CAUTION

Unplug the TV from AC mains wall socket if you do not intend to use the
TV for a long period of time. Accumulated dust can cause fire hazard
and insulation deterioration can cause electric leakage/shock/fire.

Install the product where no radio wave occurs.

Apparatus shall not be exposed to dripping or splashing and no objects

filled with liquids, such as vases, shall be placed on the apparatus.
There should be enough distance between an outside antenna and
power lines to keep the former from touching the latter even when the
Do not install this product on a wall if it could be exposed to oil or oil antenna falls. This may cause an electric shock.
mist. This may damage the product and cause it to fall.

Do not install the product on places such as unstable shelves or inclined

If water enters or comes into contact with TV, AC adapter or power surfaces. Also avoid places where there is vibration or where the
cord please disconnect the power cord and contact service centre product cannot be fully supported. Otherwise, the product may fall or
immediately. Otherwise, this may result in electric shock or fire. flip over, which may cause injury or damage to the product.

Only use an authorized AC adapter and power cord approved by

If you install the TV on a stand, you need to take actions to prevent the
LG Electronics. Otherwise, this may result in fire, electric shock,
product from overturning. Otherwise, the product may fall over, which
malfunction or product deformation.
may cause injury.

If you intend to mount the product to a wall, attach VESA standard

mounting interface (optional parts) to the back of the product. When
you install the set to use the wall mounting bracket (optional parts), fix
Never Disassemble the AC adapter or power cord. This may result in fire it carefully so as not to drop.
or electric shock.

Only use the attachments / accessories specified by the manufacturer.

5
ENGLISH

When installing the antenna, consult with a qualified service When connecting external devices such as video game consoles, make
technician. If not installed by a qualified technician, this may create a sure the connecting cables are long enough. Otherwise, the product
fire hazard or an electric shock hazard. may fall over, which may cause injury or damage the product.

We recommend that you maintain a distance of at least 2 to 7 times Do not turn the product On/Off by plugging-in or unplugging the power
the diagonal screen size when watching TV. If you watch TV for a long plug to the wall outlet. (Do not use the power plug for switch.) It may
period of time, this may cause blurred vision. cause mechanical failure or could give an electric shock.

Only use the specified type of battery. This could cause damage to the Please follow the installation instructions below to prevent the product
remote control. from overheating.
•  The distance between the product and the wall should be more
than 10 cm.
•  Do not install the product in a place with no ventilation (e.g., on a
bookshelf or in a cupboard).
•  Do not install the product on a carpet or cushion.
Do not mix new batteries with old batteries. This may cause the
•  Make sure the air vent is not blocked by a tablecloth or curtain.
batteries to overheat and leak.
Otherwise, this may result in fire.

Batteries should not be exposed to excessive heat. For example, keep

away from direct Sunlight , open fireplace and electric heaters.

Do not place non-rechargeable batteries in charging device. Take care not to touch the ventilation openings when watching the TV
for long periods as the ventilation openings may become hot. This does
not affect the operation or performance of the product.

Periodically examine the cord of your appliance, and if its appearance

Make sure there are no objects between the remote control and its indicates damage or deterioration, unplug it, discontinue use of the
sensor. appliance, and have the cord replaced with an exact replacement part
by an authorized servicer.

Signal from Remote Control can be interrupted due to external/internal

lighting eg Sunlight, fluorescent lighting. If this occurs turn off lighting
or darken viewing area.
Prevent dust collecting on the power plug pins or outlet. This may cause
a fire hazard.

6
 ENGLISH
When moving the product, make sure you turn the power off first. Then,
Protect the power cord from physical or mechanical abuse, such as
unplug the power cables, antenna cables and all connecting cables.
being twisted, kinked, pinched, closed in a door, or walked upon. Pay
The TV set or power cord may be damaged, which may create a fire
particular attention to plugs, wall outlets, and the point where the cord
hazard or cause electric shock.
exits the appliance.

Do not press strongly upon the panel with a hand or sharp object such When moving or unpacking the product, work in pairs because the
as nail, pencil or pen, or make a scratch on it, as it may cause damage product is heavy. Otherwise, this may result in injury.
to screen.

Refer all servicing to qualified service personnel. Servicing is required

Avoid touching the screen or holding your finger(s) against it for long
when the apparatus has been damaged in any way, such as power
periods of time. Doing so may produce some temporary or permanent
supply cord or plug is damaged, liquid has been spilled or objects have
distortion/damage to screen.
fallen into the apparatus, the apparatus has been exposed to rain or
moisture, does not operate normally, or has been dropped.

When cleaning the product and its components, unplug the power
first and wipe it with a soft cloth. Applying excessive force may cause
scratches or discolouration. Do not spray with water or wipe with a wet If the product feels cold to the touch, there may be a small “flicker”
cloth. Never use glass cleaner, car or industrial shiner, abrasives or wax, when it is turned on. This is normal, there is nothing wrong with
benzene, alcohol etc., which can damage the product and its panel. product.
Otherwise, this may result in fire, electric shock or product damage
(deformation, corrosion or breakage).

As long as this unit is connected to the AC wall outlet, it is not

disconnected from the AC power source even if you turn off this unit
This panel is an advanced product that contains millions of pixels.
by SWITCH.
You may see tiny black dots and/or brightly coloured dots (red, blue
or green) at a size of 1 ppm on the panel. This does not indicate a
malfunction and does not affect the performance and reliability of the
product.
This phenomenon also occurs in third-party products and is not subject
to exchange or refund.
When unplugging the cable, grab the plug and unplug it, by pulling
at the plug. Don’t pull at the cord to unplug the power cord from the
power board, as this could be hazardous.

7
 •  For an optimal connection, HDMI cables and USB devices should
have bezels less than 10 mm thick and 18 mm width. Use an
extension cable that supports USB 2.0 if the USB cable or USB
memory stick does not fit into your TV’s USB port.
ENGLISH

You may find different brightness and color of the panel depending on B
B
your viewing position(left/right/top/down). *A <
= 10 mm
This phenomenon occurs due to the characteristic of the panel. It is not *B <
related with the product performance, and it is not malfunction.
A A = 18 mm
•  Use a certified cable with the HDMI logo attached.
Displaying a still image for a prolonged period of time may cause image •  If you do not use a certified HDMI cable, the screen may not display
sticking. Avoid displaying a fixed image on the TV screen for a long or a connection error may occur. (Recommended HDMI Cable Types)
period of time. - High-Speed HDMI®/TM Cable (3 m or less)
- High-Speed HDMI®/TM Cable with Ethernet (3 m or less)
•  How to use the ferrite core (Depending on model)
Generated sound -- Use the ferrite core to reduce the electromagnetic interference in
the power cord. Wind the power cord on the ferrite core once.
“Cracking” noise: A cracking noise that occurs when watching or turning
off the TV is generated by plastic thermal contraction due to tempera- [Wall side] [TV side]
ture and humidity. This noise is common for products where thermal
deformation is required. Electrical circuit humming/panel buzzing:
A low level noise is generated from a high-speed switching circuit,
which supplies a large amount of current to operate a product. It varies
depending on the product. 10 cm (+ / -2 cm)
This generated sound does not affect the performance and reliability
of the product. •  This Smart TV is for VOD watching service, some smart functions
may not be supported including web browser. (Only LH57**)
Do not use high voltage electrical goods near the TV (e.g. electric
mosquito-swatter). This may result in product malfunction. CAUTION
•  Do not use any unapproved items to ensure the safety and product
life span.
Preparing •  Any damage or injuries caused by using unapproved items are not
covered by the manufacturer’s warranty.
•  Some models have a thin film attached on to the screen and this
NOTE
must not be removed.
•  If the TV is turned on for the first time after it was shipped from •  When attaching the stand to the TV set, place the screen facing
the factory, initialization of the TV may take a few minutes. down on a cushioned table or flat surface to protect the screen
(Depending on model) from scratches.
•  Image shown may differ from your TV. •  Make sure that the screws are inserted correctly and fastened
•  Your TV’s OSD (On Screen Display) may differ slightly from that securely. (If they are not fastened securely enough, the TV may tilt
shown in this manual. forward after being installed.) Do not use too much force and over
•  The available menus and options may differ from the input source tighten the screws; otherwise screw may be damaged and not
or product model that you are using. tighten correctly.
•  New features may be added to this TV in the future.
•  The items supplied with your product may vary depending on the
model.
•  Product specifications or contents of this manual may be changed
without prior notice due to upgrade of product functions.

8
Separate purchase CAUTION
•  Avoid touching the screen at all times, as this may result in damage
Separate purchase items can be changed or modified for quality to the screen.
improvement without any notification. Contact your dealer to buy •  Do not move the TV by holding the cable holders, as the cable

ENGLISH
these items. These devices only work with certain models. The model holders may break, and injuries and damage to the TV may occur.
name or design may be changed depending on the upgrade of product
functions, manufacturer’s circumstances or policies.
Using the button
(Depending on model)

AN-MR650 (Depending on model)

Magic Remote You can simply operate the TV functions, pressing or moving the button.

NOTE
Lifting and moving the TV •  LH57, 32/43/49LH59 series does not have a Joystick functions but
has only a power On/Off button.
Please note the following advice to prevent the TV from being scratched
or damaged and for safe transportation regardless of its type and size.
•  It is recommended to move the TV in the box or packing material
that the TV originally came in.
•  Before moving or lifting the TV, disconnect the power cord and
all cables.
•  When holding the TV, the screen should face away from you to
avoid damage.
Dome button Joystick button

or
•  Hold the top and bottom of the TV frame firmly. Make sure not to
hold the transparent part, speaker, or speaker grill area.

Basic functions
Power On (Press)
Power Off (Press and hold)1

Volume Control
•  When transporting a large TV, there should be at least 2 people.
•  When transporting the TV by hand, hold the TV as shown in the
following illustration. Programmes Control

1 All running apps will close, and any recording in progress will stop.

Adjusting the menu

•  When transporting the TV, do not expose the TV to jolts or
When the TV is turned on, press the button one time. You can adjust
excessive vibration.
the Menu items pressing or moving the buttons.
•  When transporting the TV, keep the TV upright, never turn the TV
on its side or tilt towards the left or right. Turns the power off.
•  Do not apply excessive pressure to cause flexing / bending of frame
Clears on-screen displays and returns to TV viewing.
chassis as it may damage screen.
•  When handling the TV, be careful not to damage the protruding Changes the input source.
buttons. Accesses the settings menu.

9
 Mounting on a table Securing the TV to a wall
(This feature is not available for all models.)
1 Lift and tilt the TV into its upright position on a table. 
•  Leave a 10 cm (minimum) space from the wall for proper
ENGLISH

ventilation.

10 cm

10 cm 10 cm
10 cm
1 Insert and tighten the eye-bolts, or TV brackets and bolts on the back
of the TV.
10 cm •  If there are bolts inserted at the eye-bolts position, remove the
bolts first.
2 Mount the wall brackets with the bolts to the wall.
2 Connect the power cord to a wall outlet.
Match the location of the wall bracket and the eye-bolts on the rear
CAUTION of the TV.

•  Do not place the TV near or on sources of heat, as this may result in 3 Connect the eye-bolts and wall brackets tightly with a sturdy rope.
fire or other damage. Make sure to keep the rope horizontal with the flat surface.

WARNING CAUTION

If a television is not positioned in a sufficiently stable location, it can •  Make sure that children do not climb on or hang on the TV.
be potentially hazardous due to falling. Many injuries, particularly to NOTE
children, can be avoided by taking simple precautions such as:
•  Use a platform or cabinet that is strong and large enough to
•  Using cabinets or stands recommended by the manufacturer of
support the TV securely.
the television.
•  Brackets, bolts and ropes are not provided. You can obtain
•  Only using furniture that can safely support the television.
additional accessories from your local dealer.
•  Ensuring the television is not overhanging the edge of the
supporting furniture.
•  Not placing the television on tall furniture (for example, cupboards
or bookcases) without anchoring both the furniture and the Mounting on a wall
television to a suitable support.
•  Not standing the televisions on cloth or other materials placed Attach an optional wall mount bracket at the rear of the TV carefully
between the television and supporting furniture. and install the wall mount bracket on a solid wall perpendicular to
•  Educating children about the dangers of climbing on furniture to the floor. When you attach the TV to other building materials, please
reach the television or its controls. contact qualified personnel. LG recommends that wall mounting be
performed by a qualified professional installer. We recommend the use
of LG’s wall mount bracket. LG’s wall mount bracket is easy to move with
cables connected. When you do not use LG’s wall mount bracket, please
use a wall mount bracket where the device is adequately secured to the
wall with enough space to allow connectivity to external devices. It is
advised to connect all the cables before installing fixed wall mounts.

10 cm
10 cm
10 cm

10 cm

10
Make sure to use screws and wall mount bracket that meet the VESA •  When installing the wall mounting bracket, it is recommended to
standard. Standard dimensions for the wall mount kits are described in cover the stand hole using tape, in order to prevent the influx of
the following table. dust and insects. (Depending on model)

Separate purchase (Wall mounting bracket)

ENGLISH
32/43LH57** 49LH57**
Model 32/43LH59** 49LH59**
32/40/43LH60** 49/55LH60**
VESA (A x B) (mm) 200 x 200 300 x 300 Stand hole
Standard screw M6 M6
Number of screws 4 4
LSW240B LSW350B
Wall mount bracket
MSW240 MSW240 Connections (notifications)
55LH57**
Model
55LH59** Connect various external devices to the TV and switch input modes to
VESA (A x B) (mm) 400 x 400 select an external device. For more information of external device’s
Standard screw M6 connection, refer to the manual provided with each device.
Number of screws 4 Available external devices are: HD receivers, DVD players, VCRs, audio
systems, USB storage devices, PC, gaming devices, and other external
LSW440B
Wall mount bracket devices.
MSW240
NOTE

A
•  The external device connection may differ from the model.
B •  Connect external devices to the TV regardless of the order of the
TV port.
•  If you record a TV program on a DVD recorder or VCR, make sure to
connect the TV signal input cable to the TV through a DVD recorder
or VCR. For more information of recording, refer to the manual
provided with the connected device.
CAUTION
•  Refer to the external equipment’s manual for operating
•  Remove the stand before installing the TV on a wall mount by instructions.
performing the stand attachment in reverse. •  If you connect a gaming device to the TV, use the cable supplied
with the gaming device.
NOTE •  In PC mode, there may be noise associated with the resolution,
•  When installing the wall mounting bracket, use the adhesive vertical pattern, contrast or brightness. If noise is present, change
label provided. The adhesive label will protect the opening from the PC output to another resolution, change the refresh rate to
accumulating dust and dirt. (Only when the item of the following another rate or adjust the brightness and contrast on the PICTURE
form is provided) menu until the picture is clear.
•  In PC mode, some resolution settings may not work properly
Provided item depending on the graphics card.

Antenna connection
Connect the TV to a wall antenna socket with an RF cable (75 Ω).
•  Use a signal splitter to use more than 2 TVs.
•  If the image quality is poor, install a signal amplifier properly to
Adhesive label improve the image quality.
•  If the image quality is poor with an antenna connected, try to
realign the antenna in the correct direction.
•  An antenna cable and converter are not supplied.
•  Supported DTV Audio: MPEG, Dolby Digital, Dolby Digital Plus,
HE-AAC

11
 Adapter connection CAUTION
(Depending on model) •  In Analogue TV and some countries, some remote control buttons
may not work.
CAUTION
Make sure to point the remote control toward the remote control sensor
ENGLISH

•  Please be sure to connect the TV to the AC-DC power adapter on the TV.
before connecting the TV’s power plug to a wall power outlet.

Satellite dish connection

(Only satellite models)
1 1 1 1
Connect the TV to a satellite dish to a satellite socket with a satellite RF
cable (75 Ω).
A
CI module connection
(Depending on model) 2 2
View the encrypted (pay) services in digital TV mode.
3
•  Check if the CI module is inserted into the PCMCIA card slot in the
right direction. If the module is not inserted properly, this can
3 B
cause damage to the TV and the PCMCIA card slot.
•  If the TV does not display any video and audio when CI+ CAM is
connected, please contact to the Terrestrial/Cable/Satellite Service A
Operator.
(POWER) Turns the TV on or off.
USB connection Selects Radio, TV and DTV programme.
Some USB Hubs may not work. If a USB device connected through a USB 1 (Search) Search for content such as TV programmes, movies
Hub is not detected, connect it directly to the USB port on the TV. and other videos, or perform a web search by entering text in the
search bar. (Depending on model)
1 Recalls your preferred subtitle in digital mode.
Other connections (Depending on model)
Connect your TV to external devices. For the best picture and audio 1 (INPUT) Changes the input source. (Depending on model)
quality, connect the external device and the TV with the HDMI cable. 1 By zooming in on the selected area, you can view it in
Some separate cable is not provided. full screen. (Depending on model)
1 Resizes an image. (Depending on model)
NOTE
1 (Q. Settings) Accesses the Quick Settings. (Depending on
•  Supported HDMI Audio format : model)
Dolby Digital (32 kHz, 44.1 kHz, 48 kHz), 1 Views the information of the current programme and
DTS (44.1 kHz, 48 kHz), screen. (Depending on model)
PCM (32 kHz, 44.1 kHz, 48 kHz, 96 kHz, 192 kHz) Number buttons Enters numbers.
(Depending on model) Alphabet buttons Enters letters. (Depending on model)
(SPACE) Opens an empty space on the screen keyboard.
(Depending on model)
Remote control 2 Shows programme guide. (Depending on model)
2 Accesses the saved programme list. (Depending on model)
(Depending on model) 2 Returns to the previously viewed programme. (Depending
on model)
The descriptions in this manual are based on the buttons on the remote
control. Please read this manual carefully and use the TV correctly.
To replace batteries, open the battery cover, replace batteries (1.5 V
AAA) matching the and ends to the label inside the
compartment, and close the battery cover. To remove the batteries,
perform the installation actions in reverse.

12
B D
Adjusts the volume level. 5 , By pressing the AD button, audio descriptions function
3 Accesses your favourite programme list. (Depending on will be enabled. (Depending on model)
model) 5 , Starts to record and displays record menu. (Only

ENGLISH
3 Views the information of the current programme and Time MachineReady supported model) (Depending on model)
screen. (Depending on model) 5 Sets the sleep timer. (Depending on model)
3 Shows programme guide. (Depending on model) 6 Returns to LIVE TV. (Depending on model)
3 (Search) Search for content such as TV programmes, movies Control buttons ( ) Controls media contents.
and other videos, or perform a web search by entering text in the Coloured buttons These access special functions in some menus.
search bar. (Depending on model) ( : Red, : Green, : Yellow, : Blue)
(MUTE) Mutes all sounds.
Scrolls through the saved programmes.
Moves to the previous or next screen. Magic remote functions
(Depending on model)
4 4
When the message “Magic remote battery is low. Change the battery.” is
4
C
4 displayed, replace the battery.
To replace batteries, open the battery cover, replace batteries (1.5 V AA)
matching the and ends to the label inside the compartment,
4 4 and close the battery cover. Be sure to point the magic remote toward
6 the remote control sensor on the TV. To remove the batteries, perform
5 5 the installation actions in reverse.
D CAUTION
•  In Analogue TV and some countries, some remote control buttons
may not work.

C
4 Shows the previous history. (Depending on model)
4 Teletext buttons ( ) These buttons are used for
teletext. (Depending on model)
4 Shows the list of Programmes and Recommended.
A
(Depending on model)
(HOME) Accesses the Home menu.
4 (Q. Settings) Accesses the Quick Settings. (Depending on
model)
4
4
Returns to the previous level. (Depending on model)
Accesses the Quick menus. (Depending on model)
B
4 Clears on-screen displays and returns to TV viewing.
(Depending on model)
Navigation buttons (up/down/left/right) Scrolls through menus
or options.
Selects menus or options and confirms your input.

13
 A

(POWER) Turns the TV on or off.

(STB POWER) You can turn your set-top box on or off by C
ENGLISH

adding the set-top box to the universal remote control for your TV.
Number buttons Enters numbers.
Alphabet buttons Enters letters. (Depending on model)
Accesses the saved programmes list.
(SPACE) Opens an empty space on the screen keyboard.
(Depending on model)
D
(Screen Remote) Displays the Screen Remote.
* Accesses the Universal Control Menu. (Depending on model)

Adjusts the volume level.

(MUTE) Mutes all sounds. C
* By Pressing and holding the button, audio descriptions func-
tion will be enabled. (Depending on model) Wheel (OK) Press the center of the Wheel button to select a
Scrolls through the saved programmes. menu. You can change programmes by using the wheel button.
(SEARCH) Search for content such as TV programmes, movies and (up/down/left/right) Press the up, down, left or right
other videos, or perform a web search by entering text in the search button to scroll the menu. If you press buttons while the
bar. pointer is in use, the pointer will disappear from the screen and Magic
(HOME) Accesses the Home menu. Remote will operate like a general remote control. To display the
Shows the previous history. pointer on the screen again, shake Magic Remote to the left and right.
(Voice recognition) (Depending on model)
Network connection is required to use the voice recognition function.
1 Press the voice recognition button.
D
2 Speak when the voice display window appears on the TV screen.
Displays the set-top box Home menu. Returns to the previous level.
* When you are not watching via a set-top box: the display changes Shows programme guide.
to the set-top box screen. Clears on-screen displays and returns to last input viewing.
Used for viewing 3D video. (Only 3D models)
(INPUT) Changes the input source.
* Pressing and holding the button displays all the lists of external
inputs.
(Q. Settings) Accesses the Quick Settings.
* Pressing and holding the button displays the All Settings
menu.
Coloured buttons These access special functions in some menus.
( : Red, : Green, : Yellow, : Blue)
Teletext buttons ( , ) These buttons are used for teletext.
You can zoom in on the area where the remote control is
pointed. (Depending on model)
By zooming in on the selected area, you can view it in full
screen. (Depending on model)

14
Registering magic remote Open source software
How to register the magic remote notice information
To use the Magic Remote, first pair it with your TV.

ENGLISH
To obtain the source code under GPL, LGPL, MPL, and other open source
1 Put batteries into the Magic Remote and turn the TV on. licenses, that is contained in this product, please visit http://opensource.
2 Point the Magic Remote at your TV and press the Wheel (OK) on lge.com.
the remote control. In addition to the source code, all referred license terms, warranty
* If the TV fails to register the Magic Remote, try again after turning disclaimers and copyright notices are available for download.
the TV off and back on. LG Electronics will also provide open source code to you on CD-ROM
for a charge covering the cost of performing such distribution (such
How to deregister the magic remote
as the cost of media, shipping, and handling) upon email request to
Press the and (HOME) buttons at the same time, for five opensource@lge.com. This offer is valid for three (3) years from the date
seconds, to unpair the Magic Remote with your TV. on which you purchased the product.
* Pressing and holding the button will let you cancel and re-
register Magic Remote at once.
External control device
Licenses setup
Supported licenses may differ by model. For more information about To obtain the external control device setup information, please visit
licenses, visit www.lg.com. www.lg.com.

Troubleshooting
Cannot control the TV with the remote control.
•  Check the remote control sensor on the product and try again.
(Australia region only) •  Check if there is any obstacle between the product and the remote
control.
•  Check if the batteries are still working and properly installed (
to , to ).
No image display and no sound is produced.
FreeviewPlus provides access to content and services from the
Freeview networks. The FreeviewPlus service provides a 7 + day •  Check if the product is turned on.
EPG, all available Catch Up TV, recommendations and the ability to •  Check if the power cord is connected to a wall outlet.
set reminders and favourites. FreeviewPlus is available by pressing •  Check if there is a problem in the wall outlet by connecting other
the green button on the remote. products.
The TV turns off suddenly.
* FreeviewPlus uses HbbTV technology which combines broadcast
and broadband. It requires an internet connection. Normal data •  Check the power control settings. The power supply may be
usage charges and conditions apply. interrupted.
•  Check if the Sleep Timer / Timer Power Off is activated in the
Timers settings.
•  Check if the Auto Power Off is activated in the GENERAL Eco
Mode settings. (Depending on model)
•  If there is no signal while the TV is on, the TV will turn off
automatically after 15 minutes of inactivity.
When connecting to the PC (HDMI ), ‘No signal’ or ‘Invalid Format’ is
displayed.
•  Turn the TV off/on using the remote control.
•  Reconnect the HDMI cable.
•  Restart the PC with the TV on.

15
 Specifications Digital TV Analogue TV
(Depending on (Depending on
Country) Country)
Wireless module specification
•  As band channels can vary per country, the user cannot change or PAL B/B, PAL B/G,
ENGLISH

adjust the operating frequency. This product is configured for the PAL D/K, PAL-I,
DVB-T/T21
regional frequency table. Television system SECAM B/G,
DVB-T/T2/C/S/S22
•  For consideration of the user, this device should be installed and SECAM D/K,
operated with a minimum distance of 20 cm between the device NTSC-M
and the body. VHF, UHF
Programme coverage C-Band2 VHF, UHF, CATV
(Only LH57**, LH59**) Ku-Band2

Wireless LAN module (TWFM-B006D) specification DVB-T/T2 & Analogue TV : 2,000

Maximum LH57**
number of DVB-S/S2 : 6,000
Standard IEEE802.11a/b/g/n storable LH59** DVB-T/T2 & Analogue TV : 3,000
Frequency Range Output power (Max.) programmes LH60** DVB-S/S2 : 6,000
2400 to 2483.5 MHz 14 dBm External antenna
5150 to 5250 MHz 12.5 dBm 75 Ω
impedance
5725 to 5850 MHz (for Non EU) 15.5 dBm
1 Only DVB-T2 support models. Despite DVB-T2 model, DVB-T/T2
function does not apply in Philippines.
(Only LH60**)
2 Only DVB-T2/C/S2 support models.
Wireless module (LGSBW41) specification
32LH570*, 32LH571*, 32LH572*,
Wireless LAN (IEEE 802.11a/b/g/n) 32LH59**
Frequency Range Output power (Max.) Manufacturer : APD
2400 to 2483.5 MHz 16 dBm Model : DA-48G19
5150 to 5250 MHz 16 dBm Manufacturer : Lien Chang
5725 to 5850 MHz (Not for EU) 11.5 dBm Model : LCAP45

Bluetooth Input : AC 100-240 V~ 50/60 Hz

AC/DC Adapter Output : 19 V 2.53 A
Frequency range Output power (Max.)
32LH576*, 32LH577*, 32LH578*
2400 to 2483.5 MHz 10 dBm
Manufacturer : APD
Model : DA-65F19
Manufacturer : Lien Chang
CI Module1 (W x H x D) 100.0 mm x 55.0 mm x 5.0 mm Model : LCAP40
Operating Input : AC 100-240 V~ 50/60 Hz
0 °C to 40 °C
Temperature Output : 19 V 3.42 A
Operating
Less than 80 %
Environment Humidity
•  The energy information provided with the product is indicated in
condition Storage accordance with the regulations of each country. (Depending on
-20 °C to 60 °C
Temperature Country)
Storage -- The Energy consumption is measured in accordance with IEC
Less than 85 % 62087.
Humidity
•  Actual Energy consumption may vary depending on factors such as
1 Only Satellite models. the type of video content being played and TV settings.

16
Regulatory

WARNING!

ENGLISH
Never place a television set in an unstable location. A television set may fall, causing serious personal injury or death. Many injuries, particularly to
children, can be avoided by taking simple precautions such as:
•  Using cabinets or stands recommended by the manufacturer of the television set.
•  Only using furniture that can safely support the television set.
•  Ensuring the television set is not overhanging the edge of the supporting furniture.
•  Not placing the television set on tall furniture (for example, cupboards or bookcases) without anchoring both the furniture and the television
set to a suitable support.
•  Not placing the television set on cloth or other materials that may be located between the television set and supporting furniture.
•  Educating children about the dangers of climbing on furniture to reach the television set or its controls.
If your existing television set is being retained and relocated, the same considerations as above should be applied.

Symbols

Refers to alternating current(AC).

Refers to direct current(DC).

Refers to class II equipment.

Refers to stand-by.

Refer to “ON” (power).

Refers to dangerous voltage.

17
 Environmental Information

(Only India)
ENGLISH

Disposal of your old appliance (as per e-waste Rules)

1. When this crossed out wheeled bin symbol is depicted on the product and its operator’s manual, it means the product is
covered by the e-waste Management and Handling Rules, 2011 and are meant to be recycled, dismantled, refurbished or
disposed off.
2. Do’s :
a. The product is required to be handed over only to the authorized recycler for disposal.
b. Keep the product in isolated area, after it becomes non-functional/unrepairable so as to prevent its accidental breakage.
Don’t :
a. The product should not be opened by the user himself/herself, but only by authorized service personnel.
b. The product is not meant for re-sale to any unauthorized agencies/scrap dealer/kabariwalah.
c. The product is not meant for mixing into household waste stream.

sentence
LGE Internal Use Only d. Do not keep any replaced spare part(s) from the product in exposed area.
3. Any disposal through unauthorized agencies/person will attract action under Environment (Protection) Act 1986.
4. “This product is complied with the requirement of Hazardous Substances as specified under Rule 13 (1) & (2) of the E-Waste (Management &
Handling) Rules, 2011.”
5. To locate a nearest collection centre or call for pick-up (limited area only) for disposal of this appliance, please contact Toll Free No. 1800-315-
E _ Provided sentence LGE
9999 Internal Use
/ 1800-180-9999 Only
for details. All collection centre and pick up facilities are done by third parties with LG Electronics India Pvt. Ltd.
Merely as a facilitator. For more detailed information, please visit : http://www.lge.com/in.

( ( -- )
)

. -
“
,

18
Record the model number and serial number of the TV.
Refer to the label on the back cover and quote this
information to your dealer when requiring any service.

MODEL

SERIAL
OWNER’S MANUAL

EXTERNAL CONTROL
DEVICE SETUP
Please read this manual carefully before operating the set and retain it for
future reference.

www.lg.com
 2 KEY CODES

key CODES
ENGLISH
ENG

• This feature is not available for all models.

Code Code
Function Note Function Note
(Hexa) (Hexa)
00 CH +, PR + R/C Button 53 List R/C Button
01 CH -, PR - R/C Button 5B Exit R/C Button
02 Volume + R/C Button 60 PIP(AD) R/C Button
03 Volume - R/C Button 61 Blue R/C Button
06 > (Arrow Key / Right Key) R/C Button 63 Yellow R/C Button
07 < (Arrow Key / Left Key) R/C Button 71 Green R/C Button
08 Power R/C Button 72 Red R/C Button
09 Mute R/C Button 79 Ratio / Aspect Ratio R/C Button
0B Input R/C Button 91 AD (Audio Description) R/C Button
0E SLEEP R/C Button 9E LIVE MENU R/C Button
0F TV, TV/RAD R/C Button 7A User Guide R/C Button
10 - 19 * Number Key 0 - 9 R/C Button 7C Smart / Home R/C Button
1A Q.View / Flashback R/C Button 7E Simplink R/C Button
1E FAV (Favorite Channel) R/C Button 8E ►► (Forward) R/C Button
20 Text (Teletext) R/C Button 8F ◄◄ (Rewind) R/C Button
21 T. Opt (Teletext Option) R/C Button AA Info R/C Button
28 Return (BACK) R/C Button AB Program Guide R/C Button
30 AV (Audio / Video) Mode R/C Button B0 ► (Play) R/C Button
39 Caption/Subtitle R/C Button B1 ꕗ (Stop / File List) R/C Button
40 Λ (Arrow Key / Cursor Up) R/C Button B5 RECENT R/C Button
V (Arrow Key / Cursor ꕘ (Freeze / Slow Play /
41 R/C Button BA R/C Button
Down) Pause)
42 My Apps R/C Button BB Soccer R/C Button
43 Menu / Settings R/C Button BD ꔄ (REC) R/C Button
44 OK / Enter R/C Button DC 3D R/C Button
45 Q.Menu R/C Button 99 AutoConfig R/C Button
4C List, - (ATSC Only) R/C Button 9F App / * R/C Button
4D PICTURE R/C Button 9B TV / PC R/C Button
52 SOUND R/C Button

* Key code 4C (0x4C) is available on ATSC/ISDB models which use major/minor channel.
(For South Korea, Japan, North America, Latin America except Colombia models)
 EXTERNAL CONTROL DEVICE SETUP 3

EXTERNAL CONTROL DEVICE SETUP

ENGLISH
ENG
• Image shown may differ from your TV.

Connect the USB to Serial converter/RS-232C input jack to an external control device (such as a computer
or an A/V control system) to control the product’s functions externally.

Note: The type of control port on the TV can be different between model series.

* Please be advised that not all models support this type of connectivity.
* Cable is not provided.

USB to Serial converter with USB Cable

USB Type

USB IN
(PC) (TV)

• LGTV supports PL2303 chip-based (Vendor ID : 0x0557, Product ID :IN0x2008) USB to serial converter
RS-232C
which is not made nor provided by LG. (CONTROL & SERVICE)

(PC)
• It can be purchased from computer stores that carry accessories for IT support professionals.(TV)
RS-232C With RS232C Cable
USB IN

(PC)
DE9 (D-Sub 9pin) Type
1
(TV)
• You need to purchase the RS-232C (DE9, D-Sub 3 9pin female-to-female type) to RS-232C cable required
SERVICE ONLY

for the connection between the PC and the TV, which is specified in the manual.
(PC) (TV)
2 RS-232C IN
(CONTROL & SERVICE)

(PC) (TV)
1
3

(PC)
The connection interface may differ from your TV. 1 (TV)
SERVICE ONLY

3 RS-232C IN
(CONTROL & SERVICE)
2
(PC) (TV)
2

1
3

(PC) (TV)
RS-232C IN
(CONTROL & SERVICE)
2
RS-232C IN
(CONTROL & SERVICE)

RS-232C IN
 IN IN
(PC)EXTERNAL CONTROL DEVICE SETUP
4 (TV)

USB USB
(PC) (TV)
Phone jack Type
RS-232C IN
ENGLISH

• You need to purchase the phone-jack to RS-232 cable required for &the
(CONTROL connection between the PC and
SERVICE)

(PC) (TV)
ENG

the TV, which is specified in the manual. RS-232C IN

(CONTROL & SERVICE)

(PC)
* For other models, connect to the USB port.
(TV)
* The connection interface may differ from your TV.

ONLY ONLY
3

(PC) 1
(TV)

SERVICE
3

(PC) (TV)

SERVICE
2

2
- or
1
3

(PC) 3
1 (TV)
RS-232C IN
(PC) 2
(CONTROL & SERVICE)
(TV)
RS-232C IN
(CONTROL & SERVICE)
2

Customer Computer RS-232C configurations

3-Wire Configurations(Not standard)
1 5 PC TV
RXD 2 2 TXD
RS-232C IN
(CONTROL & SERVICE)
TXD 3 1 RXD
RS-232C IN
GND
(CONTROL & SERVICE) 5 3 GND

OR
6 9
RXD 3 2 TXD
RS-232C
TXD 2 1 RXD
(Serial port)
GND 5 3 GND
D-Sub 9 Phone

Set ID
For Set ID number, see "Real Data Mapping" on p. 6

1. Press SETTINGS to access the main menus.

2. Press the Navigation buttons to scroll to (*General → About this TV or OPTION) and press OK.
3. Press the Navigation buttons to scroll to SET ID and press OK.
4. Scroll left or right to select a set ID number and select CLOSE. The adjustment range is 1-99.
5. When you are finished, press EXIT.
* (Depending on model)
 EXTERNAL CONTROL DEVICE SETUP 5

Communication Parameters

ENGLISH
ENG
• Baud rate : 9600 bps (UART) • Stop bit : 1 bit
• Data length : 8 bits • Communication code : ASCII code
• Parity : None • Use a crossed (reverse) cable.

Command reference list

(Depending on model)

DATA DATA
COMMAND1 COMMAND2 COMMAND1 COMMAND2
(Hexadecimal) (Hexadecimal)
01. Power* k a 00 to 01 15. Balance k t 00 to 64
16. Color
02. Aspect
k c (p. 7) (Colour) x u 00 to 64
Ratio
Temperature
17. ISM
03. Screen
k d (p. 7) Method (Only j p (p. 8)
Mute
Plasma TV)
04. Volume
k e 00 to 01 18. Equalizer j v (p. 8)
Mute
05. Volume 19. Energy
k f 00 to 64 j q 00 to 05
Control Saving
20. Tune
06. Contrast k g 00 to 64 m a (p. 9)
Command
21. Channel m b 00 to 01
07.
k h 00 to 64 (Programme)
Brightness
Add/Del(Skip)
08. Color/
k i 00 to 64 22. Key m c Key Codes
Colour
23. Control m g 00 to 64
Backlight,
09. Tint k j 00 to 64
Control Panel
Light
10. 24. Input x b (p. 11)
k k 00 to 32
Sharpness select (Main)
11. OSD 25. 3D (Only x t (p. 11)
k l 00 to 01
Select 3D models)
12. Remote 26. Extended x v (p. 11)
Control Lock k m 00 to 01 3D (Only 3D
Mode models)
27. Auto j u (p. 12)
13. Treble k r 00 to 64 Configure

14. Bass k s 00 to 64

* Note: During playing or recording media, all commands except Power (ka) and Key (mc) are not
executed and treated as NG.
With RS232C cable, TV can communicate "ka command" in power-on or power-off status. but with
USB-to-Serial converter cable, the command works only if TV is on.
 6 EXTERNAL CONTROL DEVICE SETUP

Transmission / Receiving Protocol

ENGLISH

Transmission
ENG

[Command1][Command2][ ][Set ID][ ][Data][Cr]

[Command 1] : First command to control the TV. (j, k, m or x)

[Command 2] : Second command to control the TV.
[Set ID] : You can adjust the [Set ID] to choose desired monitor ID number in option menu.
Adjustment range in TV is 1 to 99. If [Set ID] value is selected to ‘0’, every connected set
can be controlled.
* [Set ID] is indicated as decimal (1 to 99) on menu and as Hexadecimal (0x00 to 0x63) on
transmission/receiving protocol.
[DATA] : To transmit command data (hexadecimal). Transmit ‘FF’ data to read status of command.
[Cr] : Carriage Return - ASCII code ‘0x0D’
[ ] : Space – ASCII code ‘0x20’

OK Acknowledgement
[Command2][ ][Set ID][ ][OK][Data][x]

* The set transmits ACK (acknowledgement) based on this format when receiving normal data. At this time,
if the data is data read mode, it indicates present status data. If the data is data write mode, it returns the
data of the PC computer.

Error Acknowledgement
[Command2][ ][Set ID][ ][NG][Data][x]

* The set transmits ACK (acknowledgement) based on this format when receiving abnormal data from
non-viable functions or communication errors.

Data 00: Illegal Code

Real data mapping (Hexadecimal b Decimal)

* When you enter the [data] in hexadecimal, refer to following conversion table.
* Channel Tune (ma) Command uses two-byte hexadecimal value([data]) to select channel number.
00 : Step 0 32 : Step 50 (Set ID 50) FE : Step 254
01 : Step 1 (Set ID 1) 33 : Step 51 (Set ID 51) FF : Step 255
... ... ...
0A : Step 10 (Set ID 10) 63 : Step 99 (Set ID 99) 01 00 : Step 256
... ... ...
0F : Step 15 (Set ID 15) C7 : Step 199 27 0E : Step 9998
10 : Step 16 (Set ID 16) C8 : Step 200 27 0F : Step 9999
... ... ...
 EXTERNAL CONTROL DEVICE SETUP 7

* Commands may work differently depending on model and signal.

ENGLISH
01. Power (Command: k a)

ENG
Ack [d][ ][Set ID][ ][OK/NG][Data][x]
►► To control Power *On or Off of the set.
* In case of video mute on only, TV will display On
Transmission[k][a][ ][Set ID][ ][Data][Cr]
Screen Display(OSD). But, in case of Screen mute
on, TV will not display OSD.
Data 00 : Power Off 01 : *Power On

Ack [a][ ][Set ID][ ][OK/NG][Data][x]

04. Volume Mute (Command: k e)
►► To Show TV is Power On or *Off ►► To control volume mute on/off.
Transmission [k][a][ ][Set ID][ ][FF][Cr] You can also adjust mute using the MUTE button
on remote control.
Ack [a][ ][Set ID][ ][OK][Data][x]
Transmission [k][e][ ][Set ID][ ][Data][Cr]
* Similarly, if other functions transmit ‘FF’ data
Data 00 : Volume mute on (Volume off)
based on this format, Acknowledgement feedback
01 : Volume mute off (Volume on)
presents status about each function.
Ack [e][ ][Set ID][ ][OK/NG][Data][x]

02. Aspect Ratio (Command: k c)

(Main Picture Size) 05. Volume Control (Command: k f)
►► To adjust the screen format. (Main picture format) ►► To adjust volume.
You can also adjust the screen format using the You can also adjust volume with the volume
Aspect Ratio in the Q.MENU. or PICTURE menu. buttons on remote control.
Transmission [k][c][ ][Set ID][ ][Data][Cr] Transmission [k][f][ ][Set ID][ ][Data][Cr]
Data Min : 00 to Max : 64
Data 01 : Normal screen 07 : 14:9
(4:3) (Europe, Colombia, Mid-East, Ack [f][ ][Set ID][ ][OK/NG][Data][x]
02 : Wide screen Asia except South Korea and
(16:9) Japan)
04 : Zoom 09 : * Just Scan
05 : Zoom 2 0B : Full Wide 06. Contrast (Command: k g)
(Latin America (Europe, Colombia, Mid- ►► To adjust screen contrast.
except Colombia East, Asia except South You can also adjust contrast in the PICTURE
Only) Korea and Japan) menu.
06 : Set by Program/ 10 to 1F : Cinema Zoom 1 to 16
Transmission [k][g][ ][Set ID][ ][Data][Cr]
Original 0c : 21:9 (Depending on model)
Data Min : 00 to Max : 64
Ack [c][ ][Set ID][ ][OK/NG][Data][x]
Ack [g][ ][Set ID][ ][OK/NG][Data][x]
* Using the PC input, you select either 16:9 or 4:3
screen aspect ratio.
* In DTV/HDMI/Component mode (high-definition), 07. Brightness (Command: k h)
Just Scan is available. ►► To adjust screen brightness.
* Full wide mode may work differently based on You can also adjust brightness in the PICTURE
model and is supported for DTV fully, and ATV, menu.
AV partially. Transmission [k][h][ ][Set ID][ ][Data][Cr]

Data Min : 00 to Max : 64

03. Screen Mute (Command: k d) Ack [h][ ][Set ID][ ][OK/NG][Data][x]
►► To select screen mute on/off.
Transmission [k][d][ ][Set ID][ ][Data][Cr]
Data 00 : Screen mute off (Picture on) 08. Color/Colour (Command: k i)
Video mute off ►► To adjust the screen Color(Colour).
01 : Screen mute on (Picture off) You can also adjust colour in the PICTURE menu.
10 : Video mute on Transmission [k][i][ ][Set ID][ ][Data][Cr]
 8 EXTERNAL CONTROL DEVICE SETUP

Data Min : 00 to Max : 64 * (Depending on model)

Ack [i][ ][Set ID][ ][OK/NG][Data][x]
ENGLISH

14. Bass (Command: k s)

09. Tint (Command: k j)
ENG

►► To adjust Bass.
►► To adjust the screen tint. You can also adjust in the AUDIO menu.
You can also adjust tint in the PICTURE menu.
Transmission [k][j][ ][Set ID][ ][Data][Cr] Transmission [k][s][ ][Set ID][ ][Data][Cr]
Data Min : 00 to Max : 64
Data Red : 00 to Green : 64
Ack [s][ ][Set ID][ ][OK/NG][Data][x]
Ack [j][ ][Set ID][ ][OK/NG][Data][x]
* (Depending on model)

15. Balance (Command: k t)

10. Sharpness (Command: k k)
►► To adjust balance.
►► To adjust the screen sharpness. You can also adjust balance in the AUDIO menu.
You can also adjust sharpness in the PICTURE
menu. Transmission [k][t][ ][Set ID][ ][Data][Cr]

Transmission [k][k][ ][Set ID][ ][Data][Cr] Data Min : 00 to Max : 64

Data Min : 00 to Max : 32 Ack [t][ ][Set ID][ ][OK/NG][Data][x]

Ack [k][ ][Set ID][ ][OK/NG][Data][x]

16. Color(Colour) Temperature (Command: x u)

►► To adjust colour temperature. You can also adjust
11. OSD Select (Command: k l)
Color(Colour) Temperature in the PICTURE menu.
►► To select OSD (On Screen Display) on/off when
controlling remotely. Transmission [x][u][ ][Set ID][ ][Data][Cr]

Transmission [k][l][ ][Set ID][ ][Data][Cr] Data Min : 00 to Max : 64

Ack [u][ ][Set ID][ ][OK/NG][Data][x]
Data 00 : OSD off 01 : OSD on

Ack [l][ ][Set ID][ ][OK/NG][Data][x]

17. ISM Method (Command: j p) (Only Plasma TV)
►► To control the ISM method. You can also adjust
12. Remote control lock mode (Command: k m) ISM Method in OPTION menu.
►► To lock the front panel controls on the monitor and Transmission [j][p][ ][Set ID][ ][Data][Cr]
remote control.
Data Min : 02: Orbiter
Transmission [k][m][ ][Set ID][ ][Data][Cr] 08: Normal
20: Color(Colour) Wash
Data 00 : Lock off 01 : Lock on
Ack [p][ ][Set ID][ ][OK/NG][Data][x]
Ack [m][ ][Set ID][ ][OK/NG][Data][x]

* If you are not using the remote control, use this

mode. 18. Equalizer (Command : j v)
When main power is off & on (plug-off and plug-in, ►► Adjust EQ of the set.
after 20 - 30 seconds), external control lock is Transmission [j][v][ ][Set ID][ ][Data][Cr]
released.
MSB LSB
* In the standby mode (DC off by off timer or ‘ka’,
‘mc’ command), and if key lock is on, TV will not 0 0 0 0 0 0 0 0
turn on by power on key of IR & Local Key.

13. Treble (Command: k r) Frequency Data

►► To adjust treble.
You can also adjust in the AUDIO menu. 7 6 5 Frequency 4 3 2 1 0 Step
0 0 0 1st Band 0 0 0 0 0 0(decimal)
Transmission [k][r][ ][Set ID][ ][Data][Cr]
0 0 1 2nd Band 0 0 0 0 1 1(decimal)
Data Min : 00 to Max : 64
0 1 0 3rd Band ... ... ... ... ... ...
Ack [r][ ][Set ID][ ][OK/NG][Data][x]
0 1 1 4th Band 1 0 0 1 1 19(decimal)
 EXTERNAL CONTROL DEVICE SETUP 9

Set ID = All = 00
1 0 0 5th Band 1 0 1 0 1 20(decimal)
Data 00 & 01 = Channel Data is 10 = 00 0a
Acknowledgement [v][ ][Set ID][ ][OK/NG][Data][x] Data 02 = Analog Antenna TV = 00

ENGLISH
Result = ma 00 00 0a 00

ENG
* It depends on model, and can adjust when sound
mode is EQ adjustable value.
2. Tune to the digital antenna (DVB-T) Channel 01.
Set ID = All = 00
19. Energy Saving (Command: j q) Data 00 & 01 = Channel Data is 1 = 00 01
►► To reduce the power consumption of the TV. You Data 02 = Digital Antenna TV = 10
can also adjust Energy Saving in PICTURE menu. Result = ma 00 00 01 10
Transmission [j][q][ ][Set ID][ ][Data][Cr]
3. Tune to the satellite (DVB-S) Channel 1000.
Data Set ID = All = 00
00 : Off Data 00 & 01 = Channel Data is 1000 = 03 E8
01 : Minimum Data 02 = Digital Satellite TV = 40
02 : Medium Result = ma 00 03 E8 40
03 : Maximum
04 : Auto (For LCD TV / LED TV) / Ack [a][ ][Set ID][ ][OK][Data 00][Data 01]
Intelligent sensor (For PDP TV) [Data 02][x][a][ ][Set ID][ ][NG][Data 00][x]
05 : Screen off
• For South Korea, North/Latin America except
* (Depending on model) Colombia Model
Ack [q][ ][Set ID][ ][OK/NG][Data][x] ►► To tune channel to following physical/major/minor
number.
Transmission [m][a][ ][0][ ][Data00][ ][Data01]
20. Tune Command (Command: m a) [ ][Data02][ ][Data03][ ][Data04][ ][Data05][Cr]

* This command may work differently depending on Digital channels have a Physical, Major, and Minor
model and signal. channel number. The Physical number is the actual
• For Europe, Mid-East, Colombia, Asia except digital channel number, the Major is the number that
South Korea and Japan Model the channel should be mapped to, and the Minor is
►► Select channel to following physical number. the sub-channel. Since the ATSC tuner automatically
maps the channel from the Major / Minor number,
Transmission [m][a][ ][Set ID][ ][Data 00][ ] the Physical number is not required when sending a
[Data 01][ ][Data 02][Cr] command in Digital.
* Analog Antenna/Cable
* Analog Antenna/Cable
Data 00 : Physical Channel Number
[Data 00][Data 01] Channel Data
- Antenna (ATV) : 02~45 (Decimal: 2 ~ 69)
Data 00 : High byte channel data
- Cable (CATV) : 01, 0E~7D (Decimal : 1, 14~125)
Data 01 : Low byte channel data
- 00 00 ~ 00 C7 (Decimal : 0 ~ 199)
[Data 01 ~ 04]: Major/Minor Channel Number
Data 01 & 02: xx (Don't care)
Data 02 : Input Source (Analog)
Data 03 & 04: xx (Don't care)
- 00 : Antenna TV (ATV)
Data 05: Input Source (Analog)
- 80 : Cable TV (CATV)
- 00 : Antenna TV (ATV)
* Digital Antenna/Cable/Satellite - 01 : Cable TV (CATV)
* Digital Antenna/Cable
[Data 00][Data 01]: Channel Data
Data 00 : High Channel data
Data 00 : xx (Don't care)
Data 01 : Low Channel data
- 00 00 ~ 27 0F (Decimal: 0 ~ 9999)
[Data 01][Data 02]: Major Channel Number
Data 01 : High byte Channel Data
Data 02 : Input Source (Digital)
Data 02 : Low byte Channel Data
- 10 : Antenna TV (DTV)
- 00 01 ~ 27 0F (Decimal: 1 ~ 9999)
- 20 : Antenna Radio (Radio)
[Data 03][Data 04]: Minor Channel Number
- 40 : Satellite TV (SDTV)
Data 03 : High byte Channel Data
- 50 : Satellite Radio (S-Radio)
Data 04 : Low byte Channel Data
- 90 : Cable TV (CADTV)
- a0 : Cable Radio (CA-Radio)
Data 05 : Input Source (Digital)
- 02 : Antenna TV (DTV) – Use Physical Channel
* Tune Command Examples: Number
1. Tune to the Analog antenna (PAL) Channel 10. - 06 : Cable TV (CADTV) – Use Physical Channel
 10 EXTERNAL CONTROL DEVICE SETUP

Number Data 05 = Digital Antenna TV = 02

- 22 : Antenna TV (DTV) – Don’t Use Physical Total = ma 00 00 00 11 00 01 02
Channel Number
ENGLISH

- 26 : Cable TV (CADTV) - Don’t Use Physical

ENG

Channel Number 2. Tune to the BS (ISDB-BS) channel 30.

- 46 : Cable TV (CADTV) – Use Physical/Major Set ID = All = 00
Channel Number Only (One Part Channel) Data 00 = Don’t know Physical = 00
- 66 : Cable TV (CADTV) – Use Major Channel Data 01 & 02 = Major is 30 = 00 1E
Number Only (One Part Channel) Data 03 & 04 = Don’t Care = 00 00
Two bytes are available for each major and minor Data 05 = Digital BS TV = 07
channel data, but usually the low byte is used alone Total = ma 00 00 00 1E 00 00 07
(high byte is 0). * This feature is varied based on the model.
* Tune Command Examples: Ack [a][ ][Set ID][ ][OK][Data 00][Data 01]
1. Tune to the Analog cable (NTSC) channel 35. [Data 02][Data 03][Data 04][Data 05]
Set ID = All = 00
[x][a][ ][Set ID][ ][NG][Data 00][x]
Data 00 = Channel Data is 35 = 23
Data 01 & 02 = No Major = 00 00
Data 03 & 04 = No Minor = 00 00
Data 05 = Analog Cable TV = 01 21. Channel(Programme) Add/Del(Skip)
Total = ma 00 23 00 00 00 00 01 (Command: m b)
2. Tune to the digital antenna (ATSC) channel 30-3. ►► To skip current channel(programme) for next time.
Set ID = All = 00
Data 00 = Don’t know Physical = 00 Transmission [m][b][ ][Set ID][ ][Data][Cr]
Data 01 & 02 = Major is 30 = 00 1E
Data 03 & 04 = Minor is 3 = 00 03 Data 00 : Del(ATSC,ISDB)/Skip(DVB) 01 : Add
Data 05 = Digital Antenna TV = 22 Ack [b][ ][Set ID][ ][OK/NG][Data][x]
Total = ma 00 00 00 1E 00 03 22
* Set the saved channel status to del(ATSC, ISDB)/
Ack [a][ ][Set ID][ ][OK][Data 00][Data 01]
skip(DVB) or add.
[Data 02][Data 03][Data 04][Data 05]
[x][a][ ][Set ID][ ][NG][Data 00][x]
22. Key (Command: m c)
• For Japan Model
►► To tune channel to following physical/major/minor ►► To send IR remote key code.
number. Transmission [m][c][ ][Set ID][ ][Data][Cr]
Transmission [m][a][ ][0][ ][Data00][ ][Data01]
[ ][Data02][ ][Data03][ ][Data04][ ][Data05][Cr] Data Key code - p. 2.

* Digital Antenna/Satellite Ack [c][ ][Set ID][ ][OK/NG][Data][x]

Data 00: xx (Don't care)
23. Control Backlight (Command: m g)
[Data 01][Data 02]: Major Channel Number • For LCD TV / LED TV
Data 01: High byte Channel Data ►► To control the backlight.
Data 02: Low byte Channel Data Transmission [m][g][ ][Set ID][ ][Data][Cr]
- 00 01 ~ 27 0F (Decimal: 1 ~ 9999)
[Data 03][Data 04]: Minor/Branch Channel Number Data Min : 00 to Max : 64
(Don’t care in Satellite)
Ack [g][ ][Set ID][ ][OK/NG][Data][x]
Data 03: High byte Channel Data
Data 04: Low byte Channel Data Control Panel Light (Command: m g)
Data 05 : Input Source (Digital/Satellite for Japan)
- 02 : Antenna TV (DTV) • For Plasma TV
- 07 : BS (Broadcasting Satellite) ►► To control the panel light.
- 08 : CS1 (Communication Satellite 1) Transmission [m][g][ ][Set ID][ ][Data][Cr]
- 09 : CS2 (Communication Satellite 2)
Data Min : 00 to Max : 64
* Tune Command Examples:
1 Tune to the digital antenna (ISDB-T) channel 17-1. Ack [g][ ][Set ID][ ][OK/NG][Data][x]
Set ID = All = 00
Data 00 = Don’t know Physical = 00
Data 01 & 02 = Major is 17 = 00 11
Data 03 & 04 = Minor/Branch is 1 = 00 01
 EXTERNAL CONTROL DEVICE SETUP 11

24. Input select (Command: x b) 00 O O O

(Main Picture Input)
01 X X X

ENGLISH
►► To select input source for main picture.
02 X X X

ENG
Transmission [x][b][ ][Set ID][ ][Data][Cr]
03 X O O
Data
00 : DTV 01 : CADTV X : don’t care
02 : Satellite DTV 10 : ATV
Ack [t][ ][Set ID][ ][OK][Data00][Data01][Data02]
ISDB-BS (Japan)
03 : ISDB-CS1 (Japan) [Data03][x]
04 : ISDB-CS2 (Japan) [t][ ][Set ID][ ][NG][Data00][x]
11 : CATV
20 : AV or AV1 21 : AV2
26. Extended 3D(Command: x v) (only 3D models)
40 : Component1 41 : Component2 (Depending on model)
60 : RGB
►► To change 3D option for TV.
90 : HDMI1 91 : HDMI2
Transmission [x][v][ ][Set ID][ ][Data 00][ ]
92 : HDMI3 93 : HDMI4
[Data 01][Cr]
Ack [b][ ][Set ID][ ][OK/NG][Data][x]
[Data 00] 3D option
* This function depends on model and signal. 00 : 3D Picture Correction
01 : 3D Depth (3D Mode is Manual Only)
02 : 3D Viewpoint
25. 3D(Command: x t) (only 3D models) 06 : 3D Color Correction
(Depending on model) 07 : 3D Sound Zooming
►► To change 3D mode for TV. 08 : Normal Image View
09 : 3D Mode (Genre)
Transmission [x][t][ ][Set ID][ ][Data 00][ ][Data 01]
[ ][Data 02][ ][Data 03][Cr] [Data 01] It has own range for each 3D option
* (Depending on model) determined by [Data 00].
Data Structure 1) When [Data 00] is 00
[Data 00] 00 : 3D On 00 : Right to Left
01 : 3D Off 01 : Left to Right
02 : 3D to 2D
03 : 2D to 3D 2) When [Data 00] is 01, 02
[Data 01] 00 : Top and Bottom Data Min: 0 - Max: 14 (*transmit by Hexadecimal
01 : Side by Side code)
02 : Check Board Data value range(0 - 20) converts Viewpoint range
03 : Frame Sequential (-10 - +10) automatically (Depending on model)
04 : Column interleaving * This option works when 3D Mode (Genre) is manual
05 : Row interleaving only.
[Data 02] 00 : Right to Left
01 : Left to Right 3) When [Data 00] is 06, 07
[Data 03] 3D Effect(3D Depth): Min : 00 - Max : 14 00 : Off
(*transmit by Hexadecimal code) 01 : On
* [Data 02], [Data 03] functions depend on model
and signal. 4) When [Data 00] is 08
00 : Revert to 3D video from 3D-to-2D
* If [Data 00] is 00 (3D On), [Data 03] has no
converted 2D video
meaning.
01 : Change 3D video to 2D video, except
* If [Data 00] is 01 (3D off) or 02 (3D to 2D), [Data 2D-to-3D video
01], [Data 02] and [Data 03] have no meaning. * If conversion condition doesn’t meet, command is
* If [Data 00] is 03 (2D to 3D), [Data 01] and treated as NG.
[Data 02] have no meaning.
* If [Data 00] is 00 (3D On) or 03 (2D to 3D), [Data 5) When [Data 00] is 09
03] works when 3D Mode (Genre) is manual only. 00 : Standard 01 : Sport
* All 3D pattern options ([Data 01]) may not be 02 : Cinema 03 : Extreme
available according to broadcasting/video signal. 04 : Manual 05 : Auto

Ack [v][ ][Set ID][ ][OK][Data00][Data01][x]

[Data 00] [Data 01] [Data 02] [Data 03]
[v][ ][Set ID][ ][NG][Data00][x]
 12 EXTERNAL CONTROL DEVICE SETUP

27. Auto Configure (Command: j u)

(Depending on model)
ENGLISH

►► To adjust picture position and minimize image

ENG

shaking automatically. It works only in RGB (PC)

mode.
Transmission [j][u][ ][Set ID][ ][Data][Cr]
Data 01 : Run Auto Configure

Ack [u][ ][Set ID][ ][OK/NG][Data][x]