Air Bag System

1712-1U-01G(08-10).
fm 1 ページ２００１年６月２９日金曜日午前１０時２４分
AIR BAG SYSTEM

08–10 AIR BAG SYSTEM
LOCATION INDEX . . . . . . . . . . . . . . . . . 08–10–2 Connector Removal Note . . . . . . . . . . . 08–10–11
AIR BAG SYSTEM SERVICE Connector Installation Note. . . . . . . . . . 08–10–11
WARNINGS . . . . . . . . . . . . . . . . . . . . . . 08–10–3 SAS CONTROL MODULE
Component Disassembly . . . . . . . . . . . 08–10–3 REMOVAL/INSTALLATION . . . . . . . . . . 08–10–12
Wiring Harness Repair . . . . . . . . . . . . . 08–10–3 SAS CONTROL MODULE BRACKET
Air Bag Module Inspection . . . . . . . . . . 08–10–3 REMOVAL/INSTALLATION . . . . . . . . . . 08–10–12
Air Bag Module Handling . . . . . . . . . . . 08–10–3 AIR BAG MODULE AND
Side Air Bag Module Handling . . . . . . . 08–10–4 PRE-TENSIONER
SAS Control Module Handling . . . . . . . 08–10–4 SEAT BELT DEPLOYMENT
Side Air Bag Sensor Handling . . . . . . . 08–10–4 AUTHORIZATION PROCEDURES . . . . 08–10–13
Pre-tensioner Seat Belt Inspection . . . 08–10–5 After Replacing SAS Control Module . . 08–10–13
Component Handling . . . . . . . . . . . . . . 08–10–5 After Replacing Side Air Bag Sensor . . 08–10–13
Component Reuse . . . . . . . . . . . . . . . . 08–10–5 AIR BAG MODULE AND
DRIVER-SIDE AIR BAG MODULE PRE-TENSIONER
REMOVAL/INSTALLATION . . . . . . . . . 08–10–5 SEAT BELT DEPLOYMENT
Connector Installation Note . . . . . . . . . 08–10–6 PROCEDURES . . . . . . . . . . . . . . . . . . . . 08–10–13
PASSENGER-SIDE AIR BAG MODULE Deployment Procedure for
REMOVAL/INSTALLATION . . . . . . . . . 08–10–6 Inside of Vehicle . . . . . . . . . . . . . . . . . 08–10–13
Connector Installation Note . . . . . . . . . 08–10–6 Deployment Procedure for
SIDE AIR BAG MODULE Outside of Vehicle . . . . . . . . . . . . . . . . 08–10–16
REMOVAL/INSTALLATION . . . . . . . . . 08–10–7 AIR BAG MODULE AND
CLOCK SPRING ADJUSTMENT . . . . . . 08–10–8 PRE-TENSIONER
CLOCK SPRING SEAT BELT DISPOSAL
REMOVAL/INSTALLATION . . . . . . . . . 08–10–9 PROCEDURES . . . . . . . . . . . . . . . . . . . . 08–10–23 08–10
CLOCK SPRING INSPECTION. . . . . . . . 08–10–10 INSPECTION OF SST
SIDE AIR BAG SENSOR (DEPLOYMENT TOOL) . . . . . . . . . . . . . 08–10–24
REMOVAL/INSTALLATION . . . . . . . . . 08–10–10 Inspection Procedure . . . . . . . . . . . . . . 08–10–24
End of Toc
08–10–1
1712-1U-01G(08-10).fm 2 ページ２００１年６月２９日金曜日午前１０時２４分
AIR BAG SYSTEM

LOCATION INDEX
A3U081001046W01
Z3U0810W007
1 Driver-side air bag module 6 SAS control module

(See 08–10–5 DRIVER-SIDE AIR BAG MODULE (See 08–10–12 SAS CONTROL MODULE
REMOVAL/INSTALLATION) REMOVAL/INSTALLATION)
2 Passenger-side air bag module (See 08–10–12 SAS CONTROL MODULE
(See 08–10–6 PASSENGER-SIDE AIR BAG BRACKET REMOVAL/INSTALLATION)
MODULE REMOVAL/INSTALLATION) 7 Driver-side side air bag sensor
3 Clock spring (See 08–10–10 SIDE AIR BAG SENSOR
(See 08–10–8 CLOCK SPRING ADJUSTMENT) REMOVAL/INSTALLATION)
(See 08–10–9 CLOCK SPRING REMOVAL/ 8 Passenger-side side air bag sensor
INSTALLATION) (See 08–10–10 SIDE AIR BAG SENSOR
(See 08–10–10 CLOCK SPRING INSPECTION) REMOVAL/INSTALLATION)
4 Driver-side side air bag module 9 Driver-side pre-tensioner seat belt
(See 08–10–7 SIDE AIR BAG MODULE (See 08–11–1 FRONT SEAT BELT REMOVAL/
REMOVAL/INSTALLATION) INSTALLATION)
5 Passenger-side side air bag module 10 Passenger-side pre-tensioner seat belt
(See 08–10–7 SIDE AIR BAG MODULE (See 08–11–1 FRONT SEAT BELT REMOVAL/
REMOVAL/INSTALLATION) INSTALLATION)
End Of Sie
08–10–2
AIR BAG SYSTEM

AIR BAG SYSTEM SERVICE WARNINGS
A3U081001046W02
Component Disassembly
• Disassembling and reassembling the
components of the air bag system can render
the system inoperative, which may result in
serious injury or death in the event of an
accident. Do not disassemble any air bag
system component.
YDE81301200
Wiring Harness Repair

• Incorrectly repairing an air bag system wiring
harness can accidentally deploy the air bag
module or pre-tensioner seat belt, which can
cause serious injury. If a problem is found in
the system wiring, replace the wiring harness.
Do not try to repair it.
08–10
YDE81301201
Air Bag Module Inspection

• Inspecting an air bag module using an
ohmmeter can deploy the air bag module,
which may cause serious injury. Do not use
an ohmmeter to inspect an air bag module.
Always use the on-board diagnostic function
to diagnose the air bag module for
malfunctions. (See 08–02–2 FOREWORD.)
X3U810WA2
Air Bag Module Handling

• A live (undeployed) air bag module may
accidentally deploy when it is handled and
cause serious injury. When carrying a live
(undeployed) air bag module, point the front
surface away from your body to lessen the
chance of injury in case it deploys.
YDE81301004
08–10–3
AIR BAG SYSTEM

• A live (undeployed) air bag module placed
face down on a surface is dangerous. If the air
bag module deploys, the motion of the
module can cause serious injury. Always face
the front surface up to reduce the motion of
the module in case it accidentally deploys.
YDE81301005
Side Air Bag Module Handling

• When the side air bag module deploys due to a collision, the interior of the seat back (pad, frame, etc.)
may become damaged. If the seat back is reused and the side air bag module does not deploy properly,
a serious accident may result. When the side air bag module deploys, always replace both the side air
bag module and the seat back (pad, frame, trim) with new parts. After service, confirm that the seat
operates normally and that the harness is positioned properly.
SAS Control Module Handling

• Disconnecting the SAS control module connector or removing the SAS control module with the
ignition switch at ON position can cause the air bag modules to deploy, which may seriously injure
you. Before disconnecting the SAS control module connector or removing the SAS control module,
turn the ignition switch to LOCK position, then disconnect the negative battery cable and wait for more
than 1 minute to allow the backup power supply of the SAS control module to deplete its stored power.
• Connecting the SAS control module connector without firmly installing the SAS control module to the
vehicle is dangerous. The crash sensor inside the control module may send an electrical signal to the
air bag modules. This will deploy the air bag modules, which may result in serious injury. Therefore,
before connecting the connector, firmly mount the control module to the vehicle.
• For vehicles with a single point sensor, once an air bag module is deployed due to an accident or other
causes, the SAS control module must be replaced with a new one even if the used one does not have
any external signs of damage. The used SAS control module may have been damaged internally which
may cause improper operation, resulting in major injuries or even death. The used single point SAS
control module cannot be bench-checked or self-checked.
Side Air Bag Sensor Handling

• Disconnecting the side air bag sensor connector or removing the side air bag sensor with the ignition
switch at ON position can cause the side air bag sensor to operate and the side air bag module to
deploy, which may seriously injure you. Before disconnecting the side air bag sensor connector or
removing the side air bag sensor, always turn the ignition switch to LOCK position, then disconnect
the negative battery cable and wait for more than 1 minute to allow the backup power supply of the
SAS control module to deplete its stored power.
• If the side air bag sensor is subjected to shock or the sensor is disassembled, the side air bag module
may operate (deploy) suddenly and cause injury, or it may fail to operate normally and cause a serious
accident. Do not subject the side air bag sensor to shock or disassemble the sensor.
• Because a sensor is built into the side air bag sensor, when the side air bag module operates
(deploys), there may be a problem, such as an internal malfunction, even if there is not any external
damage or deformation. If the side air bag sensor is reused, the side air bag module may fail to operate
normally and cause a serious injury. Always replace the side air bag sensor with a new part. The side
air bag sensor cannot be bench-checked or self-checked.
08–10–4
AIR BAG SYSTEM

Pre-tensioner Seat Belt Inspection
• Inspecting a pre-tensioner seat belt using an
ohmmeter can deploy the pre-tensioner seat
belt, which can cause serious injury. Do not
use an ohmmeter to inspect the pre-tensioner
seat belt. Always use the on-board diagnostic
to diagnose the pre-tensioner seat belt for
malfunctions.
Z3U0810W003
Component Handling
• Oil, grease, water, etc. on components may cause the air bag modules and pre-tensioner seat belt to
fail to deploy in an accident, which may cause serious injury. Do not allow oil, grease, water, etc., on
components.
• Inserting a screwdriver, etc. into the
connector of an air bag module or a pre-
tensioner seat belt may damage the connector
and cause the air bag module to deploy
improperly, which may cause serious injury.
Do not insert any foreign objects into the
connector.
08–10
Z3U0810W004
Component Reuse
• Even if an air bag module or a pre-tensioner seat belt does not deploy in a collision and does not have
any external signs of damage, it may have been damaged internally, which may cause improper
operation. Improper operation may cause serious injury. Always self-check the undamaged air bag
module or pre-tensioner seat belt to determine whether it can be reused. (See 08–02–2 FOREWORD.)
End Of Sie
DRIVER-SIDE AIR BAG MODULE REMOVAL/INSTALLATION
A3U081057010W01
Warning
• Handling the air bag module improperly can accidentally deploy the air bag module, which may
seriously injure you. Read AIR BAG SYSTEM SERVICE WARNINGS before handling the air bag
module. (See 08–10–3 AIR BAG SYSTEM SERVICE WARNINGS.)
1. Turn the ignition switch to LOCK position.

2. Disconnect the negative battery cable and wait for more than 1 minute.
3. Remove in the order indicated in the table.
1 Cover
2 Bolt
3 Connector
(See 08–10–6 Connector Installation Note)
4 Driver-side air bag module
4. Install in the reverse order of removal.

5. Turn the ignition switch to ON position.
6. Verify that the air bag system warning light
illuminates for approximately 6 seconds and
then goes off.
• If the air bag system warning light does not
operate in the manner described above, there
are malfunctions in the system. Inspect the
system using the on-board diagnostic
function. (See 08–02–2 FOREWORD.)
A3U0810W101
08–10–5
AIR BAG SYSTEM

Connector Installation Note
1. Install the connector and secure the car-side
harness onto the hook as shown in the figure.
End Of Sie
A3U0810W002
PASSENGER-SIDE AIR BAG MODULE REMOVAL/INSTALLATION

A3U081057050W01
Warning

3. Remove the glove compartment.
1 Connector
2 Bolt
3 Passenger-side air bag module

then goes off.
operate in the manner described above, there
system using the on-board diagnostic
function. (See 08–02–2 FOREWORD.)
X3U810WAA

1. Install the connector as shown in the figure.
End Of Sie
Y3U810WAN
08–10–6
AIR BAG SYSTEM

SIDE AIR BAG MODULE REMOVAL/INSTALLATION
A3U081000147W01
Warning
Warning
• If the side air bag module is installed with a foreign body in the seat back, the debris may be
scattered when the side air bag module operates (deploys), causing injury. Verify that there is no
foreign body in the seat back before installing the side air bag module.
1. Remove the front seat. (See 09–13–1 FRONT SEAT REMOVAL/INSTALLATION.)

2. Remove the harness clips.
Y3U810WA2
3. Undo the hook on the seat back cushion. 08–10
Y3U810WA3
4. Unzip the seat back trim.
Y3U810WA4
5. Remove the harness belts.
Y3U810WA5
08–10–7
AIR BAG SYSTEM

6. Remove the hog rings.
7. Turn over the seat back cushion.
Y3U810WA6
8. Remove the nuts to remove the side air bag

module.
Warning
• If the air bag harness is not secured at
the marked point or the harness is
caught, the side air bag module may fail
to operate (deploy) in an accident,
causing a serious accident. Be sure to
secure the air bag harness at the marked
point, and make sure the harness is not
caught during operation of the seat.
Y3U810WA7

11. Verify that the air bag system warning light illuminates for approximately 6 seconds and then goes off.
• If the air bag system warning light does not operate in the manner described above, there are malfunctions
in the system. Inspect the system using the on-board diagnostic function. (See 08–02–2 FOREWORD.)
End Of Sie
CLOCK SPRING ADJUSTMENT
A3U081066123W01
Note
• The adjustment procedure is also specified on the caution label of the clock spring.
1. Set the front wheels straight ahead.
Caution
• The clock spring will break if over-wound. Do not forcibly turn the clock spring when turning it.
2. Turn the clock spring clockwise until it stops.
X3U810WAF
08–10–8
AIR BAG SYSTEM

3. Turn the clock spring counterclockwise 2 3/4
turns.
X3U810WAG
4. Align the mark on the clock spring with the mark

on the outer housing.
End Of Sie
X3U810WAH
08–10
CLOCK SPRING REMOVAL/INSTALLATION
A3U081066123W02
1. Disconnect the negative battery cable.
2. Remove the driver-side air bag module. (See 08–10–5 DRIVER-SIDE AIR BAG MODULE REMOVAL/
INSTALLATION.)
3. Remove the steering wheel. (See 06–12–6 STEERING WHEEL AND COLUMN REMOVAL/INSTALLATION.)
4. Remove the column cover.
1 Connector
2 Screw
3 Clock spring

End Of Sie
X3U810WAE
08–10–9
AIR BAG SYSTEM

CLOCK SPRING INSPECTION
A3U081066123W03
1. Remove the clock spring. (See 08–10–9 CLOCK SPRING REMOVAL/INSTALLATION.)
2. Inspect for continuity between the clock spring terminals using an ohmmeter.
• If not as specified, replace the clock spring.
X3U810WAJ
Y3U810WA8
Note
• When the vehicle-side connector of clock spring is disconnected, the terminals 1A and 1B are shorted to
prevent unexpected deployment of the air bag module. When it is connected, the terminals are open.
End Of Sie
SIDE AIR BAG SENSOR REMOVAL/INSTALLATION
A3U081000146W01
Warning
• Handling the side air bag sensor improperly can accidentally deploy the side air bag module,
which may seriously injure you. Read AIR BAG SYSTEM SERVICE WARNINGS before handling the
side air bag sensor. (See 08–10–3 AIR BAG SYSTEM SERVICE WARNINGS.)

3. Remove the B-pillar lower trim. (See 09–17–10 B-PILLAR LOWER TRIM REMOVAL.)
1 Bolt
2 Connector
(See 08–10–11 Connector Removal Note)
3 Side air bag sensor
Note
• When a new side air bag sensor has been
installed, perform the air bag module Y3U810WA9
deployment authorization procedure. (See
08–10–13 AIR BAG MODULE AND PRE-TENSIONER SEAT BELT DEPLOYMENT AUTHORIZATION
PROCEDURES.)
08–10–10
AIR BAG SYSTEM

• If the air bag system warning light does not operate in the manner described above, there are malfunctions
in the system. Inspect the system using the on-board diagnostic function. (See 08–02–2 FOREWORD.)
Connector Removal Note

1. Slide the connector cover toward the harness and then
disconnect the connector from the side air bag sensor.
08–10
Y3U810WAA

1. Attach the connector to the side air bag sensor.
2. Connect the connector by attaching it to the side air
bag sensor while lifting up the lock on the connector
with a flathead screwdriver.
End Of Sie
Y3U810WAB
08–10–11
AIR BAG SYSTEM

SAS CONTROL MODULE REMOVAL/INSTALLATION
A3U081057030W01
Warning
• Handling the SAS control module improperly can accidentally deploy the air bag modules, which
may seriously injure you. Read AIR BAG SYSTEM SERVICE WARNINGS before handling the SAS
control module. (See 08–10–3 AIR BAG SYSTEM SERVICE WARNINGS.)

3. Remove the side walls.
1 Connector
2 Bolt
3 SAS control module

then goes off.
operate in the manner described above, there X3U810WAC

system using the on-board diagnostic function. (See 08–02–2 FOREWORD.)
Note
• When a new SAS control module has been installed, the air bag system warning light flashes continuously
if there aren't any malfunctions in the system. Perform the air bag module deployment authorization
procedure. (See 08–10–13 AIR BAG MODULE AND PRE-TENSIONER SEAT BELT DEPLOYMENT
AUTHORIZATION PROCEDURES.)
End Of Sie
SAS CONTROL MODULE BRACKET REMOVAL/INSTALLATION
A3U081057030W02
1. Remove the SAS control module. (See 08–10–12 SAS CONTROL MODULE REMOVAL/INSTALLATION.)
1 Nut
2 SAS control module bracket

End Of Sie
X3U810WAD
08–10–12
AIR BAG SYSTEM

AIR BAG MODULE AND PRE-TENSIONER SEAT BELT DEPLOYMENT AUTHORIZATION PROCEDURES
A3U081057000W01
Note
• When replacing both the SAS control module and side air bag sensor together, perform only “After
Replacing SAS Control Module”
After Replacing SAS Control Module

1. Install a new SAS control module.
(1) Turn the ignition switch to ON position.
(2) Verify that the air bag system warning light illuminates for approximately 6 seconds, goes off, and then
flashes continuously.
• If the air bag system warning light does not flash continuously and indicates a DTC, inspect the system
using the on-board diagnostic function. (See 08–02–2 FOREWORD.) When the malfunctions have
been repaired and the air bag system warning light flashes continuously, turn the ignition switch to
LOCK position. Wait for approximately 1 second or more and then turn the ignition switch back to ON
position.
• If the air bag system warning light flashes continuously, turn the ignition switch to LOCK position. Wait
for approximately 1 second or more and then turn the ignition switch back to ON position.
• If the light stays on, perform the deployment authorization procedure again.
After Replacing Side Air Bag Sensor

1. Install a new side air bag sensor.
• If the light stays on, perform the deployment authorization procedure again. 08–10
End Of Sie
AIR BAG MODULE AND PRE-TENSIONER SEAT BELT DEPLOYMENT PROCEDURES
A3U081057000W02
Warning
• A live (undeployed) air bag module and pre-tensioner seat belt may accidentally deploy when it is
disposed of and cause serious injury. Do not dispose of a live (undeployed) air bag module. If the
SSTs (Deployment tool and Adapter harness) are not available, consult the nearest Mazda
representative for assistance.
Caution
• Deploying the air bag modules inside the vehicle may cause damage to the vehicle interior. When
the vehicle is not to be scrapped, always deploy the air bag modules and pre-tensioner seat belts
outside the vehicle.
• When the vehicle is to be scrapped, deploy the air bag modules and pre-tensioner seat belts inside the vehicle.
(See 08–10–13 Deployment Procedure for Inside of Vehicle.)
• When the vehicle is not to be scrapped, deploy the air bag modules and pre-tensioner seat belts outside the
vehicle. (See 08–10–16 Deployment Procedure for Outside of Vehicle.)
Note
• When disposing of a deployed air bag module, refer to air bag module and pre-tensioner seat belt
disposal procedure. (See 08–10–23 AIR BAG MODULE AND PRE-TENSIONER SEAT BELT DISPOSAL
PROCEDURES.)
Deployment Procedure for Inside of Vehicle

1. Inspect the SST (Deployment tool). (See 08–10–24 INSPECTION OF SST (DEPLOYMENT TOOL).)
2. Move the vehicle to an open space, away from strong winds, and close all of the vehicle's doors and windows.
5. Follow the appropriate procedure for deploying the driver-side air bag module, passenger-side air bag module,
or side air bag module.
08–10–13
AIR BAG SYSTEM

Driver-side air bag module
1. Remove the column cover.
2. Disconnect the clock spring connector.
3. Connect the SST (Adapter harness) to the clock
spring as shown in the figure.
X3U810WAL
4. Connect the SST (Deployment tool) to the SST

(Adapter harness).
5. Connect the red clip of the SST (Deployment tool)
to the positive battery terminal and the black clip
to the negative battery terminal.
6. Verify that the red light on the SST (Deployment
tool) is illuminated.
7. Make sure all persons are standing at least 6 m
{20 ft} away from the vehicle.
X3U810WAM
8. Press the activation switch on the SST

(Deployment tool) to deploy the driver-side air
bag module.
X3U810WAN
Passenger-side air bag module

1. Remove the glove compartment.
2. Disconnect the passenger-side air bag module connector.
3. Connect the SST (Adapter harness) to the
passenger-side air bag module as shown in the
figure.
X3U810WAP
08–10–14
AIR BAG SYSTEM

(Adapter harness).
{20 ft} away from the vehicle.
X3U810WAQ

(Deployment tool) to deploy the passenger-side
air bag module.
X3U810WAR
08–10
Side air bag module
1. Disconnect the side air bag module connector.
2. Connect the SST (Adapter harness) to the side
air bag module.
Y3U810WAC

(Adapter harness).
6. Make sure all persons are standing at lest 6 m
{20ft} from the vehicle.
Y3U810WAD
08–10–15
AIR BAG SYSTEM

(Deployment tool) to deploy the side air bag
module.
Y3U810WAE
Pre-tensioner seat belt

1. Remove the B-pillar lower trim.
2. Remove the pre-tensioner seat belt and connect
the SST (49 D066 003) to it as shown in the
figure.
3. Install the pre-tensioner seat belt.
Z3U0810W005
4. Connect the SST (49 H066 002) to the SST (49

D066 003).
5. Connect the red clip of the SST (49 H066 002) to
the positive battery terminal and the black clip to
the negative battery terminal.
6. Verify that the red light on the SST (49 H066 002)
is illuminated.
{20 ft} from the vehicle.
XME8126W005
8. Press the activation switch on the SST (49 H066

002) to deploy the pre-tensioner seat belt.
YMU810WBB
Deployment Procedure for Outside of Vehicle

1. Inspect the SST (Deployment tool). (See 08–10–24 INSPECTION OF SST (DEPLOYMENT TOOL).)
4. Follow the appropriate procedure for deploying the driver-side air bag module, passenger-side air bag module,
or side air bag module.
08–10–16
AIR BAG SYSTEM

Driver-side air bag module
1. Remove the driver-side air bag module. (See 08–10–5 DRIVER-SIDE AIR BAG MODULE REMOVAL/
INSTALLATION.)
2. Place the driver-side air bag module on the center of the wheel with the module facing up. See the illustration
below.
• To secure the air bag module to the wheel,
wrap the wire harness through the wheel and
the bolt installation hole at least 4 times.
Warning
• If the air bag module is not properly
installed to the wheel, serious injury may
occur when the module is deployed.
When installing the air bag module to the
wheel, make sure the module is facing
up.
A3U0810W102
3. Connect the SST (Adapter harness) to the driver-

side air bag module as shown in the figure.
08–10
A3U0810W103
4. Stack 3 tires on top of the tire with the air bag

module. Stack another tire that has a wheel on
top of the 4 tires.
X3U810WAW
08–10–17
AIR BAG SYSTEM

5. Tie all tires together with wire.
X3U810WAX

(Adapter harness).
{20 ft} away from the tires.
X3U810WAY

(Deployment tool) to deploy the driver-side air
bag module.
X3U810WAZ
Passenger-side air bag module

1. Remove the passenger-side air bag module. (See 08–10–6 PASSENGER-SIDE AIR BAG MODULE
REMOVAL/INSTALLATION.)
2. Install the bolts to the passenger-side air bag
module.
Warning
installed to the tire, serious injury may
tire, make sure the module is facing the
center of the tire.
X3U810WB0
08–10–18
AIR BAG SYSTEM

3. Tie the passenger-side air bag module to a tire
with the module facing the center of the tire. Wrap
the wire harness through the tire and around the
bolts at least four times.
X3U810WB1
4. Connect the SST (Adapter harness) to the

passenger-side air bag module as shown in the
figure.
X3U810WB2
08–10
5. Stack the tire with the passenger-side air bag
module on top of 2 tires. Stack a tire on top of the
3 tires. Stack another tire that has a wheel on top
of the 4 tires.
X3U810WB3
X3U810WB4
08–10–19
AIR BAG SYSTEM

(Adapter harness).
{20 ft} away from the tires.
X3U810WB5

(Deployment tool) to deploy the passenger-side
air bag module.
X3U810WB6
Side air bag module

1. Remove the side air bag module. (See 08–10–7 SIDE AIR BAG MODULE REMOVAL/INSTALLATION.)
2. Install the nuts to the side air bag module.
Warning
installed to the tire, serious injury may
tire, make sure the module is facing the
center of the tire.
Y3U810WAF
3. Tie the side air bag module to the tire with the
module facing the center of the tire. Wrap the wire
harness through the tire and around the nuts at
least 4 times.
Y3U810WAG
08–10–20
AIR BAG SYSTEM

4. Connect the SST (Adapter harness) to the side
air bag module as shown in the figure.
Y3U810WAH
5. Stack the tire with the side air bag module on top
of 2 tires. Stack a tire on top of 3 tires. Stack
another tire that has a wheel on top of the 4 tires.
08–10
Y3U810WAJ
Y3U810WAK

(Adapter harness).
{20ft} from the tires.
Y3U810WAL
08–10–21
AIR BAG SYSTEM

(Deployment tool) to deploy the side air bag
module.
Y3U810WAM
Pre-tensioner seat belt

1. Remove the pre-tensioner seat belt.
2. Connect the SST (49 D066 003) to the pre-
tensioner seat belt as shown in the figure.
Warning
• If the pre-tensioner seat belt is not
properly installed to the tire, serious
injury may occur when the pre-tensioner
part is deployed. When installing the pre-
tensioner seat belt to the tire, make sure
the pre-tensioner part is inside the tire.
Z3U0810W005
3. With the pre-tensioner part inside the tire, tie the

pre-tensioner seat belt to the tire. Wrap the wire
harness through the tire and around the pre-
tensioner seat belt at least four times.
Z3U0810W006
4. Stack the tire with the pre-tensioner seat belt on

top of two tires. Stack a tire on top of the three
tires. Stack another tire that has a wheel on top of
the four tires.
YLE8130W201
08–10–22
AIR BAG SYSTEM

XME8126W008
6. Connect the SST (49 H066 002) to the SST (49

D066 003).
7. Connect the red clip of the SST (49 H066 002) to
the positive battery terminal and the black clip to
the negative battery terminal.
8. Verify that the red light on the SST (49 H066 002)
is illuminated.
{20 ft} from the vehicle.
XME8126W009
08–10
10. Press the activation switch on the SST (49 H066
002) to deploy the pre-tensioner seat belt.
End Of Sie
XME8126W010
AIR BAG MODULE AND PRE-TENSIONER SEAT BELT DISPOSAL PROCEDURES

A3U081057000W03
Warning
• Before scrapping a vehicle with a live (undeployed) air bag module and pre-tensioner seat belt,
deploy the air bag module. Never dispose of a live (undeployed) air bag module and pre-tensioner
seat belt.
• The air bag module and pre-tensioner seat belt are very hot immediately after it is deployed. You
can get burned. Do not touch the air bag module and pre-tensioner seat belt for at least 15 minutes
after deployment.
• Pouring water on the deployed air bag module and pre-tensioner seat belt are dangerous. The
water will mix with the residual gases to form a gas that can make breathing difficult. Do not pour
water on the deployed air bag module and pre-tensioner seat belt.
• The deployed air bag module and pre-tensioner seat belt may contain deposits of sodium
hydroxide, a caustic by product of the gas-generated combustion. If this substance gets into your
eyes or on your hands, it can cause irritation and itching. When handling the deployed air bag
module and pre-tensioner seat belt, wear gloves and safety glasses.
1. Put on gloves and safety glasses.

2. Put the deployed air bag module or pre-tensioner seat belt in a plastic bag, seal it, and then dispose of it.
3. Wash your hands after removing your gloves.
End Of Sie
08–10–23
AIR BAG SYSTEM

INSPECTION OF SST (DEPLOYMENT TOOL)
A3U081001078W01
• Use the SST (Deployment tool) to deploy a live
(undeployed) air bag module before disposing of
it.
• Before using the SST (Deployment tool), inspect
its operation.
X3U810WB7
Inspection Procedure
1. Follow the steps below to verify that the SST (Deployment tool) is operating correctly.
• If not as specified, do not use the SST (Deployment tool) because it may cause the air bag module to
unexpectedly deploy upon connection to the air bag module.
Light condition
Step Inspection procedure
Green Red
Connect red clip to positive
1 battery terminal and black clip On Off
to negative battery terminal.
Connect connectors A and B
2 Off On
of SST (Deployment tool).
3 Press activation switch. On Off
End Of Sie
X3U810WB8
08–10–24

Air Bag System

Uploaded by

Copyright:

Available Formats

Air Bag System

Uploaded by

Document Information

Original Title

Copyright

Available Formats

Share this document

Share or Embed Document

Sharing Options

Did you find this document useful?

Is this content inappropriate?

Copyright:

Available Formats

Air Bag System

Uploaded by

Copyright:

Available Formats

1712-1U-01G(08-10).

AIR BAG SYSTEM

AIR BAG SYSTEM

1 Driver-side air bag module 6 SAS control module

AIR BAG SYSTEM

Wiring Harness Repair

Air Bag Module Inspection

Air Bag Module Handling

AIR BAG SYSTEM

Side Air Bag Module Handling

SAS Control Module Handling

Side Air Bag Sensor Handling

AIR BAG SYSTEM

1. Turn the ignition switch to LOCK position.

4. Install in the reverse order of removal.

AIR BAG SYSTEM

PASSENGER-SIDE AIR BAG MODULE REMOVAL/INSTALLATION

1. Turn the ignition switch to LOCK position.

5. Install in the reverse order of removal.

Connector Installation Note

AIR BAG SYSTEM

1. Remove the front seat. (See 09–13–1 FRONT SEAT REMOVAL/INSTALLATION.)

3. Undo the hook on the seat back cushion. 08–10

4. Unzip the seat back trim.

5. Remove the harness belts.

AIR BAG SYSTEM

8. Remove the nuts to remove the side air bag

9. Install in the reverse order of removal.

1. Set the front wheels straight ahead.

2. Turn the clock spring clockwise until it stops.

AIR BAG SYSTEM

4. Align the mark on the clock spring with the mark

6. Install in the reverse order of removal.

AIR BAG SYSTEM

1. Turn the ignition switch to LOCK position.

5. Install in the reverse order of removal.

AIR BAG SYSTEM

Connector Removal Note

Connector Installation Note

AIR BAG SYSTEM

1. Turn the ignition switch to LOCK position.

5. Install in the reverse order of removal.

are malfunctions in the system. Inspect the

3. Install in the reverse order of removal.

AIR BAG SYSTEM

After Replacing SAS Control Module

After Replacing Side Air Bag Sensor

Deployment Procedure for Inside of Vehicle

AIR BAG SYSTEM

4. Connect the SST (Deployment tool) to the SST

8. Press the activation switch on the SST

Passenger-side air bag module

AIR BAG SYSTEM

8. Press the activation switch on the SST

3. Connect the SST (Deployment tool) to the SST

AIR BAG SYSTEM

Pre-tensioner seat belt

4. Connect the SST (49 H066 002) to the SST (49

8. Press the activation switch on the SST (49 H066