This document is a mid-semester examination for a 3rd semester Mechanical Engineering course on Engineering Mechanics. It contains 4 multiple choice questions worth 1 mark each. It also contains 2 problems worth 4 marks each involving calculating forces between spheres in equilibrium, forces on a hanging circular roller, and reactions on two inclined rollers. Students have 2 hours to complete the examination which is out of a total of 20 marks.
This document is a mid-semester examination for a 3rd semester Mechanical Engineering course on Engineering Mechanics. It contains 4 multiple choice questions worth 1 mark each. It also contains 2 problems worth 4 marks each involving calculating forces between spheres in equilibrium, forces on a hanging circular roller, and reactions on two inclined rollers. Students have 2 hours to complete the examination which is out of a total of 20 marks.
This document is a mid-semester examination for a 3rd semester Mechanical Engineering course on Engineering Mechanics. It contains 4 multiple choice questions worth 1 mark each. It also contains 2 problems worth 4 marks each involving calculating forces between spheres in equilibrium, forces on a hanging circular roller, and reactions on two inclined rollers. Students have 2 hours to complete the examination which is out of a total of 20 marks.
This document is a mid-semester examination for a 3rd semester Mechanical Engineering course on Engineering Mechanics. It contains 4 multiple choice questions worth 1 mark each. It also contains 2 problems worth 4 marks each involving calculating forces between spheres in equilibrium, forces on a hanging circular roller, and reactions on two inclined rollers. Students have 2 hours to complete the examination which is out of a total of 20 marks.
TECHNOLOGY, PATNA GOVERNMENT ENGINEERING COLLEGE, SIWAN (BIHAR)-841226 MID SEMESTER EXAMINATION, FEBRUARY 2023
TIME ALLOTTED-2 HRS FULL MARKS-20
DEPARTMENT- MECHANICAL ENGINEERING SUBJECT-ENGINEERING MECHANICS SEMESTER- 3RD SUBJECT CODE- ESC 202 INSTRUCTIONS: ALL QUESTIONS ARE COMPULSORY. Q.1 Multiple Choice Question:- 1X4= 4 Marks (i) Lami’s theorem is applicable for a) three collinear forces b) three coplanar and concurrent forces c) three parallel forces d) all of these. (ii) The forces which meet at one point at their lines of action also lie on the same plane are known as (a) coplaner non-concurrent (b) non coplaner concurrent (c) coplaner concurrent (d) none of the above (iii) If the resultant of two equal forces has the same magnitude as either of the forces, then the angle between the two forces is (a) 30° (b) 60° (c) 90° (d) 120° (iv) The angle between two forces when the resultant is maximum and minimum respectively are (a) 0° and 180° (b) 180° and 0° (c) 90° and 180° (d) 90° and 0°
2. (a) Find the resultant by parallelogram law of forces graphically 2 marks
(b) State and prove Lami’s Theorem. 3 marks (c ) The magnitude of the resultant of two concurrent forces including an angle of 90 degree between them is √13 kN. When this included angle is changed to 60 degree, the magnitude of the resultant becomes √19 kN. Find the magnitude of the two forces. 3 marks
1. Two smooth spheres of weight W and radius r each are
in equilibrium in a horizontal channel of A and B vertical sides as shown in Fig. Find the force exerted by each sphere on the other. Calculate these values, if r = 250 mm, b = 900 mm and W = 100 N.
4 marks 2. A circular roller of weight 100 N and radius 10 cm hangs by a ties rod AB = 20 cm and rests against a smooth vertical wall at C as shown in the Figure. Determine the force F in the rod and normal reaction at C. OR
4 marks Two inclined rollers, each of weight 100 N are supported by an inclined plane and a vertical wall as shown in the Figure. Assuming smooth surfaces find the reactions induced at points A ,B and C.
