Professional Documents
Culture Documents
HSD070I651
HSD070I651
TO :
Date :
Note:1.Please contact HannStar Display Corp. before designing your product based on this
module specification.
2.The information contained herein is presented merely to indicate the characteristics and
performance of our products. No responsibility is assumed by HannStar for any intellectual
property claims or other problems that may result from application based on the module
described herein.
The information contained in this document is the exclusive property of HannStar Display Corporation. It shall not
be disclosed, distributed or reproduced in whole or in part without written permission of HannStar Display
Corporation.
H a n n Sta r Di sp l a y C o rp .
Document Title HSD070I651 Specification Page No. 2/26
Record of Revisions
Rev. Date Description of change
1.0 April.4, 2006 CAS of HSD070I651-C00 was first issued.
The information contained in this document is the exclusive property of HannStar Display Corporation. It shall not
be disclosed, distributed or reproduced in whole or in part without written permission of HannStar Display
Corporation.
H a n n Sta r Di sp l a y C o rp .
Document Title HSD070I651 Specification Page No. 3/26
Contents
The information contained in this document is the exclusive property of HannStar Display Corporation. It shall not
be disclosed, distributed or reproduced in whole or in part without written permission of HannStar Display
Corporation.
H a n n Sta r Di sp l a y C o rp .
Document Title HSD070I651 Specification Page No. 4/26
1.2 Features
■ 7 (16:9 diagonal) inch configuration
■ Compatible with NTSC & PAL system
■ Image Reversion: UP/DOWN and LEFT/RIGHT
1.3 Applications
■ Portable TV
■ Portable DVD
■ Multimedia applications and Others AV system
The information contained in this document is the exclusive property of HannStar Display Corporation. It shall not
be disclosed, distributed or reproduced in whole or in part without written permission of HannStar Display
Corporation.
H a n n Sta r Di sp l a y C o rp .
Document Title HSD070I651 Specification Page No. 5/26
The information contained in this document is the exclusive property of HannStar Display Corporation. It shall not
be disclosed, distributed or reproduced in whole or in part without written permission of HannStar Display
Corporation.
H a n n Sta r Di sp l a y C o rp .
Document Title HSD070I651 Specification Page No. 6/26
Note (1) Permanent damage may occur to the LCD module if beyond this specification.
Functional operation should be restricted to the conditions described under
normal operating conditions.
(2) Ta =25±2
The information contained in this document is the exclusive property of HannStar Display Corporation. It shall not
be disclosed, distributed or reproduced in whole or in part without written permission of HannStar Display
Corporation.
H a n n Sta r Di sp l a y C o rp .
Document Title HSD070I651 Specification Page No. 7/26
Response Rising TR 5 7
=0 msec (1)(3)
time Falling TF 20 28
Normal
White luminance (1)(4)
YL viewing 255 300 cd/m2
(Center) (IL=6.0mA)
angle
Color Wx 0.26 0.31 0.36
chromaticity White (1)(4)
(CIE1931) Wy 0.28 0.33 0.38
L 50 60
Hor.
R 50 60
Viewing angle CR>10
U 30 40
Ver.
D 50 60
Brightness uniformity BUNI =0 70 % (5)
3.2 Measuring Condition
■ Measuring surrounding : dark room
■ Lamp current IFL : 6.0±0.1mA(rms), Lamp freq. FL=50KHz, Inverter : HIU-766-22pF
■ Ambient temperature : 25±2oC
■ 30min. warm-up time.
The information contained in this document is the exclusive property of HannStar Display Corporation. It shall not
be disclosed, distributed or reproduced in whole or in part without written permission of HannStar Display
Corporation.
H a n n Sta r Di sp l a y C o rp .
Document Title HSD070I651 Specification Page No. 8/26
!U
12’ o’clock
"=90o
!L !R
"=180o "=0o
!D
6’ o’clock
"=270o
The information contained in this document is the exclusive property of HannStar Display Corporation. It shall not
be disclosed, distributed or reproduced in whole or in part without written permission of HannStar Display
Corporation.
H a n n Sta r Di sp l a y C o rp .
Document Title HSD070I651 Specification Page No. 9/26
TR TF
100%
90%
Optical
response
10%
0%
time
Photo-detector (BM-5A)
50cm
Center of panel
Field=2°
LCD panel
The information contained in this document is the exclusive property of HannStar Display Corporation. It shall not
be disclosed, distributed or reproduced in whole or in part without written permission of HannStar Display
Corporation.
H a n n Sta r Di sp l a y C o rp .
Document Title HSD070I651 Specification Page No. 10/26
Y2 Y3 Y4
25%
Y9 Y5
Y1
50%
Y8 Y7 Y6
75%
The information contained in this document is the exclusive property of HannStar Display Corporation. It shall not
be disclosed, distributed or reproduced in whole or in part without written permission of HannStar Display
Corporation.
H a n n Sta r Di sp l a y C o rp .
Document Title HSD070I651 Specification Page No. 11/26
CCFL CN1
Source Driver
Input
FPC
CN2
1,480
1,1 1,2 1,3 1,4
2,1
LCD Display Area
1 Pixel
234 Lines
R G B R
234,1 480
R 234
The information contained in this document is the exclusive property of HannStar Display Corporation. It shall not
be disclosed, distributed or reproduced in whole or in part without written permission of HannStar Display
Corporation.
H a n n Sta r Di sp l a y C o rp .
Document Title HSD070I651 Specification Page No. 12/26
Note (1) Selection of scanning mode (please refer to the following table)
Setting of scan control
IN/OUT state for start pulse Scanning direction
input
U/D L/R STVD STVU STHR STHL
GND DVDD Output Input Output Input up to down, and from left to right.
DVDD GND Input Output Input Output down to up, and from right to left.
GND GND Output Input Input Output up to down, and from right to left.
DVDD DVDD Input Output Output Input down to up, and from left to right.
Note (2) MOD=H: Simultaneous sampling.(Please check CPH2 and CPH3 to GND when MOD=H)
MOD=L : Sequential sampling.
The information contained in this document is the exclusive property of HannStar Display Corporation. It shall not
be disclosed, distributed or reproduced in whole or in part without written permission of HannStar Display
Corporation.
H a n n Sta r Di sp l a y C o rp .
Document Title HSD070I651 Specification Page No. 13/26
The information contained in this document is the exclusive property of HannStar Display Corporation. It shall not
be disclosed, distributed or reproduced in whole or in part without written permission of HannStar Display
Corporation.
H a n n Sta r Di sp l a y C o rp .
Document Title HSD070I651 Specification Page No. 14/26
The information contained in this document is the exclusive property of HannStar Display Corporation. It shall not
be disclosed, distributed or reproduced in whole or in part without written permission of HannStar Display
Corporation.
H a n n Sta r Di sp l a y C o rp .
Document Title HSD070I651 Specification Page No. 15/26
Note (1) Lamp current is measured with current meter for high frequency as
shown below. Specified valued are for single lamp.
LCD MODULE
RED
WHITE(Ground)
1 INVERTER
2 A (HIU 766-22pF)
Note (3) Lamp life time (Hr) can be defined as the time in which it continues to
operate under the condition : Ta=25±3 oC, typical IL value indicated in
the above table and fL=50kHz until the brightness becomes less than
50%.
Note (4) CCFL inverter should be able to provide a voltage over specified
value (Vs) in the above table. Lamp units need at least Vs value
shown above to ignition.
The information contained in this document is the exclusive property of HannStar Display Corporation. It shall not
be disclosed, distributed or reproduced in whole or in part without written permission of HannStar Display
Corporation.
H a n n Sta r Di sp l a y C o rp .
Document Title HSD070I651 Specification Page No. 16/26
Note (5) The voltage over specified value (Vs) should be applied to the lamp more than
1
second after startup. Otherwise, the lamp may not be turned on. The used lamp
current is the lamp typical current.
Note (6) The output voltage waveform and current waveform of the inverter must be
symmetrical (Unsymmetrical ratio is less than 10%). Please do not use the
inverter which has unsymmetrical voltage and current waveform, and spike
waveform. The inverter design which can provide the best optical performance,
power efficiency, and lamp life should under the following conditions.
a. The asymmetry rate of the inverter waveform should be less than 10%.
b. The distortion tae of the waveform should be within 2±10%.
c. The inverter output waveform should be better similar to the ideal sine wave.
Ip
I-p
The information contained in this document is the exclusive property of HannStar Display Corporation. It shall not
be disclosed, distributed or reproduced in whole or in part without written permission of HannStar Display
Corporation.
H a n n Sta r Di sp l a y C o rp .
Document Title HSD070I651 Specification Page No. 17/26
6.3 AC Characteristics
Symbo
Item Min. Typ. Max. Unit Note
l
Rising time tr - - 10 ns (1)
Falling time tf - - 10 ns (1)
High and low level pulse duty tCPH 100 103 - ns CPH1~CPH3
CPH pulse duty tCWH 40 50 60 CPH1~CPH3
STH setup time tSUH 20 - - ns STHR,STHL
STH hold time tHDH 10 - - ns STHR,STHL
STH pulse width tSTH - 1 - tCPH STHR,STHL
STH period tH 61.5 63.5 65.5 µs STHR,STHL
OEH pulse width tOEH - 1.23 - µs OEH
Sample and hold disable time tDIS1 - 8.19 - µs
OEV pulse width tOEV - 4.77 - µs OEV
CKV pulse width tCKV - 3.91 - µs CKV
Clean enable time tDIS2 - 3.90 - µs
Horizontal display timing range tDH - 1440 - tCPH/3
STV setup time tSUV 200 - - ns STVD,STVU
STV hold time tHDV 300 - - ns STVD,STVU
STV pulse width tSTV - 1 - tH STVD,STVU
Horizontal line per field tV 256 262 268 tH (2)
Vertical display start tSV 3 - tH
Vertical display timing range tDV 234 - tH
VCOM Rising time trCOM - 5 µs
VCOM Falling time tfCOM - 5 µs
VCOM delay time tDCOM - 3 µs
RGB delay time tDRGB * 1 µs
Note (1): For all of the logic signals.
Note (2): Please don’t use odd horizontal lines to drive LCD panel for both odd and
even filed simultaneously.
The information contained in this document is the exclusive property of HannStar Display Corporation. It shall not
be disclosed, distributed or reproduced in whole or in part without written permission of HannStar Display
Corporation.
H a n n Sta r Di sp l a y C o rp .
Document Title HSD070I651 Specification Page No. 18/26
tCPH
tr tf
tCWH
CPH1
tSUH tHDH
VR,VB,VG
tSTH
tSUH tHDH
STHL(R)
tOEH tDIS1
OEH
STHL(R)
(Input)
STHR(L)
(Output)
CPH1
tDH
1H
HSYNC
OEH tH
STHL(R)
The information contained in this document is the exclusive property of HannStar Display Corporation. It shall not
be disclosed, distributed or reproduced in whole or in part without written permission of HannStar Display
Corporation.
H a n n Sta r Di sp l a y C o rp .
Document Title HSD070I651 Specification Page No. 19/26
tOEV
OEV
tDIS2 tCKV
CKV
tDCM
VCOM 90%
VCAC 10%
tfCOM trCOM
BlanK
Black
White White
ViDC
VR,VG,VB ViAC ViA
tDRGB
White
Black
HSYNC
VSYNC
tSV
STVD(U)
VCOM(ODD)
VCOM(EVEN)
Vertical timing
tSTV
STVD(U) tHDV
tSUV Vertical Shift timing
CKV
tCKV
The information contained in this document is the exclusive property of HannStar Display Corporation. It shall not
be disclosed, distributed or reproduced in whole or in part without written permission of HannStar Display
Corporation.
H a n n Sta r Di sp l a y C o rp .
Document Title HSD070I651 Specification Page No. 20/26
DVDD
DVDD
GND GND
VGL VGL
10%
Note Apply the lamp volatge within the LCD operation range. When the back-light turns on
before the LCD operation or the LCD truns off before the back-light turns off.
the display may momentarily become white.
The information contained in this document is the exclusive property of HannStar Display Corporation. It shall not
be disclosed, distributed or reproduced in whole or in part without written permission of HannStar Display
Corporation.
H a n n Sta r Di sp l a y C o rp .
Document Title HSD070I651 Specification Page No. 21/26
The information contained in this document is the exclusive property of HannStar Display Corporation. It shall not
be disclosed, distributed or reproduced in whole or in part without written permission of HannStar Display
Corporation.
H a n n Sta r Di sp l a y C o rp .
Document Title HSD070I651 Specification Page No. 22/26
The information contained in this document is the exclusive property of HannStar Display Corporation. It shall not
be disclosed, distributed or reproduced in whole or in part without written permission of HannStar Display
Corporation.
H a n n Sta r Di sp l a y C o rp .
Document Title HSD070I651 Specification Page No. 23/26
10 11 12 13 14 15
HSD070I651
-C00
Rev: 00
Lot mark
The information contained in this document is the exclusive property of HannStar Display Corporation. It shall not
be disclosed, distributed or reproduced in whole or in part without written permission of HannStar Display
Corporation.
H a n n Sta r Di sp l a y C o rp .
Document Title HSD070I651 Specification Page No. 24/26
The information contained in this document is the exclusive property of HannStar Display Corporation. It shall not
be disclosed, distributed or reproduced in whole or in part without written permission of HannStar Display
Corporation.
H a n n Sta r Di sp l a y C o rp .
Document Title HSD070I651 Specification Page No. 25/26
11.6 Operation
11.6.1 Do not touch, push or rub the polarizer with anything harder than HB pencil lead.
11.6.2 Use fingerstalls of soft gloves in order to keep clean display quality, when persons
handle the LCD module for incoming inspection or assembly.
11.6.3 When the surface is dusty, please wipe gently with absorbent cotton or other soft
material.
The information contained in this document is the exclusive property of HannStar Display Corporation. It shall not
be disclosed, distributed or reproduced in whole or in part without written permission of HannStar Display
Corporation.
H a n n Sta r Di sp l a y C o rp .
Document Title HSD070I651 Specification Page No. 26/26
11.6.4 Wipe off saliva or water drops as soon as possible. If saliva or water drops contact
with polarizer for a long time, they may causes deformation or color fading.
11.6.5 When cleaning the adhesives, please use absorbent cotton wetted with a little
petroleum benzine or other adequate solvent.
11.7 Mechanism
Please mount LCD module by using mouting holes arranged in four corners tightly.
11.10 Disposal
When disposing LCD module, obey the local environmental regulations.
The information contained in this document is the exclusive property of HannStar Display Corporation. It shall not
be disclosed, distributed or reproduced in whole or in part without written permission of HannStar Display
Corporation.