HSD070I651

H a n n Sta r Di sp l a y C o rp .
Document Title HSD070I651 Specification Page No. 1/26
Document No. Revision 1.0
TO :
Date :
Customer Acceptance Specification
Model : HSD070I651- C00
Note:1.Please contact HannStar Display Corp. before designing your product based on this
module specification.
2.The information contained herein is presented merely to indicate the characteristics and
performance of our products. No responsibility is assumed by HannStar for any intellectual
property claims or other problems that may result from application based on the module
described herein.
The information contained in this document is the exclusive property of HannStar Display Corporation. It shall not
be disclosed, distributed or reproduced in whole or in part without written permission of HannStar Display
Corporation.
Record of Revisions
Rev. Date Description of change
1.0 April.4, 2006 CAS of HSD070I651-C00 was first issued.
Corporation.
Contents
1.0 General description ……………………………….… p.4
2.0 Absolute maximum ratings …………………………. p.6
3.0 Optical characteristics ………………………………. p.7
4.0 Block diagram …………………………….. ……….. p.11
5.0 Interface pin connection ……………………………. p.12
6.0 Electrical characteristics ……………………………. p.14
7.0 Reliability test items…………………………………… p.21
8.0 Outline dimension …………………………….…… p.22
9.0 Lot mark ……………………………………………... p.23
10.0 Package specification ………………………………. p.24
11.0 General precaution ……………………………………. p.25
Corporation.
1.0 GENERAL DESCRIPTION

1.1 Introduction
HannStar Display model HSD070I651-C00 is a color active matrix thin film
transistor (TFT) liquid crystal display (LCD) that uses amorphous silicon TFT as a
switching device. This model is composed of a TFT LCD panel, a driving circuit and
a back light system. This TFT LCD has a 7.0 (16:9) inch diagonally measured active
display area with 1440 x 234 dot (480 horizontal by 234 vertical pixel) resolution.
1.2 Features
■ 7 (16:9 diagonal) inch configuration
■ Compatible with NTSC & PAL system
■ Image Reversion: UP/DOWN and LEFT/RIGHT
1.3 Applications
■ Portable TV
■ Portable DVD
■ Multimedia applications and Others AV system
1.4 General information

Item Specification Unit
Outline Dimension 164.9 x 100 x 5.5 (Typ.) mm
Display area 154.08(H) x 86.58(V) mm
Number of Pixel 480 RGB(H) x234(V) pixels
Pixel pitch 0.321(H) x 0.370(V) mm
Pixel arrangement RGB Vertical stripe
Display mode Normally white
Surface treatment Antiglare, Hard-Coating(3H) with WV film
Weight 160 (Typ.) g
Back-light Single CCFL (Side-Light type)
Power Logic System 36.4(Typ.) mW
Consumption B/L System 3.28(Typ.) W
Corporation.
1.5 Mechanical Information

Item Min. Typ. Max. Unit
Horizontal(H) 164.4 164.9 165.4 mm
Module
Vertical(V) 99.5 100.0 100.5 mm
Size
Depth(D) 5.5 5.8 mm
Weight (Without inverter) 160 170 g
Corporation.
2.0 ABSOLUTE MAXIMUM RATINGS

2.1 Electrical Absolute Rating
2.1.1 TFT LCD Module
Item Symbol Min. Max. Unit Note
DVDD -0.3 6.0 V GND=0
VGH -0.3 40 V GND=0
VGL -20 0.3 V GND=0
Power supply voltage
VGH - VGL -0.3 40 V
AVDD -0.3 7.0 V AGND=0
VCOM -1.6 5.2 V
Analog Signal Input Level VR, VG, VB -0.2 AVDD+0.2 V
Logic Signal Input Level VI -0.3 DVDD +0.3 V
2.1.2 Back-Light Unit

Lamp current IL 0 7.0 mA (1) (2)
Lamp frequency fL 0 100 KHz (1) (2)
Note (1) Permanent damage may occur to the LCD module if beyond this specification.
Functional operation should be restricted to the conditions described under
normal operating conditions.
(2) Ta =25±2
2.2 Environment Absolute Rating

Operating Temperature Topa -10 60
Storage Temperature Tstg -20 70
Corporation.
3.0 OPTICAL CHARACTERISTICS

3.1 Optical specification
Item Symbol Condition Min. Typ. Max. Unit Note
Contrast CR 400 500 (1)(2)
Response Rising TR 5 7
=0 msec (1)(3)
time Falling TF 20 28
Normal
White luminance (1)(4)
YL viewing 255 300 cd/m2
(Center) (IL=6.0mA)
angle
Color Wx 0.26 0.31 0.36
chromaticity White (1)(4)
(CIE1931) Wy 0.28 0.33 0.38
L 50 60
Hor.
R 50 60
Viewing angle CR>10
U 30 40
Ver.
D 50 60
Brightness uniformity BUNI =0 70 % (5)
3.2 Measuring Condition
■ Measuring surrounding : dark room
■ Lamp current IFL : 6.0±0.1mA(rms), Lamp freq. FL=50KHz, Inverter : HIU-766-22pF
■ Ambient temperature : 25±2oC
■ 30min. warm-up time.
Corporation.
3.3 Measuring Equipment

■ Otsuka Electrics Corp., which utilized LCD-7000 for
Chromaticity and BM-5 for other optical characteristics.
■ Measuring spot size : 10 ~ 12 mm
Note (1) Definition of Viewing Angle :
!U
12’ o’clock
"=90o
!L !R
"=180o "=0o
!D
6’ o’clock
"=270o
Note (2) Definition of Contrast Ratio(CR) :

measured at the center point of panel
Luminance with all pixels white

CR =
Luminance with all pixels black
Corporation.
Note (3) Definition of Response Time : Sum of TR and TF
white(TFT OFF) black (TFT ON) white(TFT OFF)
TR TF
100%
90%
Optical
response
10%
0%
time
Note (4) Definition of optical measurement setup
Photo-detector (BM-5A)
50cm
Center of panel
Field=2°
LCD panel
Corporation.
Note (5) Definition of brightness uniformity
25% 50% 75%
Y2 Y3 Y4
25%
Y9 Y5
Y1
50%
Y8 Y7 Y6
75%
(Min Luminance of 9 points)

Luminance uniformity = #100%
(Max Luminance of 9 points)
Corporation.
4.0 BLOCK DIAGRAM

4.1 TFT LCD Module
CCFL CN1
LCD Panel Scan

Driver
Source Driver
Input
FPC
CN2
4.2 Pixel Format
1,480
1,1 1,2 1,3 1,4
2,1
LCD Display Area
1 Pixel
234 Lines
R G B R
234,1 480
R 234
480 Pixels(1440 dots)
Corporation.
5.0 INTERFACE PIN CONNECTION

5.1 TFT LCD Module
CN2 (Input signal): FPC Down Connector, 26 pins, pitch: 0.5mm
Terminal
Symbol I/O Function Note
no.
1 DGND - Ground for logic circuit
2 DVDD I Supply voltage of logic control circuit for scan (Gate) driver
3 VGL I Negative power for scan (Gate) driver
4 VGH I Positive power for scan (Gate) driver
5 STVD I/O Vertical start pulse (1)
6 STVU I/O Vertical start pulse (1)
7 CKV I Shift clock input for scan (Gate) driver
8 U/D I UP/DOWN scan control input (1)
9 OEV I Output enable input for scan(Gate) driver
10 VCOM I Common electrode driving signal
11 VCOM I Common electrode driving signal
12 L/R I LEFT/RIGHT scan control input (1)
13 MOD I Sequential sampling and simultaneous sampling setting (2)
14 OEH I Output enable input for data (Source) driver
15 STHL I/O Start pulse for horizontal scan (Gate) line (1)
16 STHR I/O Start pulse for horizontal scan (Gate) line (1)
17 CPH3 I Sampling and shifting clock pulse for data (Source) driver (2)
18 CPH2 I Sampling and shifting clock pulse for data (Source) driver (2)
19 CPH1 I Sampling and shifting clock pulse for data (Source) driver
20 DVDD I Supply voltage of logic control circuit for data(Source) driver
21 DGND - Ground for logic circuit
22 VR I Alternated video signal input(Red)
23 VG I Alternated video signal input(Green)
24 VB I Alternated video signal input(blue)
25 AVDD I Supply voltage for analog circuit
26 AGND - Ground for analog circuit
Note (1) Selection of scanning mode (please refer to the following table)
Setting of scan control
IN/OUT state for start pulse Scanning direction
input
U/D L/R STVD STVU STHR STHL
GND DVDD Output Input Output Input up to down, and from left to right.
DVDD GND Input Output Input Output down to up, and from right to left.
GND GND Output Input Input Output up to down, and from right to left.
DVDD DVDD Input Output Output Input down to up, and from left to right.
Note (2) MOD=H: Simultaneous sampling.(Please check CPH2 and CPH3 to GND when MOD=H)
MOD=L : Sequential sampling.
Corporation.
5.2 Back-Light Unit

CN1 CCFL Power Source (BHSR-02VS-1 or equivalent) / JAPAN SOLDERLESS TERMINAL MFG
CO., LTD.
Mating Connector: (SBHT-002T-P0.5) / JAPAN SOLDERLESS TERMINAL MFG CO., LTD.
Terminal no. Symbol Function
1 VL CCFL power supply (high voltage)
2 GL CCFL power supply (low voltage)
Corporation.
6.0 ELECTRICAL CHARACTERISTICS

6.1 TFT LCD Module
Item Symbol Min. Typ. Max. Unit Note
DVDD 3 3.3 5.5 V
VGH 14.3 15 15.7 V
Supply Voltage
VGL -10.5 -10 -9.5 V
AVDD 4.5 5 5.5 V
Video signal ViA 0.4 - AVDD-0.4 V
amplitude ViAC - 3 - V AC component,
(VR,VG,VB) ViDC - AVDD/2 - V DC component
VCAC - 4.7 - VP-P AC component
VCOM
VCDC 1.6 1.8 2.0 V DC component, (1)
Input signal ViH 0.8DVDD - DVDD V (2)
voltage ViL 0 - 0.2 DVDD V (2)
IDD - 127 - uA DVDD =3.3V
Current of power IADD - 7.0 - mA AVDD=5V(Black)
supply IGH - 70 - uA VGH=15V
IGL - 65 - uA VGL=-10V
Note (1): The brightness of LCD panel could be changed by adjusting the AC component of VCOM.
Note (2): STHL, STHR, OEH, L/R, CPH1~CPH3, STVD, STVU, OEV, CKV, U/D
Note (3): Be sure to apply the power voltage as the power sequence spec.
Note (4) : DGND=AGND=0V,)
Corporation.
6.2 Back-Light Unit

The back-light system is an edge-lighting type with 1 CCFL(Cold Cathode Fluorescent Lamp).
The characteristics of the lamp is shown in the following tables.
Item Symbol Min. Typ. Max. Unit Note
Lamp current IL 3.0 6.0 7.0 mA(rms) (1)(6)
Lamp voltage VL 496 548 610 V(rms) (6)IL=6.0mA
Frequency fL 40 50 80 KHz (2)
Operating lamp life time Hr 15,000 Hour (3)
1000 (4)(5)at 25oC
Startup voltage Vs V(rms)
1330 (4)(5)at 0oC
Note (1) Lamp current is measured with current meter for high frequency as
shown below. Specified valued are for single lamp.
LCD MODULE
RED
WHITE(Ground)
1 INVERTER
2 A (HIU 766-22pF)
Note (2) Lamp frequency may produce interference with horizontal

synchronous frequency and this may cause ripple noise on the
display. Therefore lamp frequency shall be kept away from the
horizontal synchronous frequency and its harmonics as far as
possible in order to avoid interference.
Note (3) Lamp life time (Hr) can be defined as the time in which it continues to
operate under the condition : Ta=25±3 oC, typical IL value indicated in
the above table and fL=50kHz until the brightness becomes less than
50%.
Note (4) CCFL inverter should be able to provide a voltage over specified
value (Vs) in the above table. Lamp units need at least Vs value
shown above to ignition.
Corporation.
Note (5) The voltage over specified value (Vs) should be applied to the lamp more than
1
second after startup. Otherwise, the lamp may not be turned on. The used lamp
current is the lamp typical current.
Note (6) The output voltage waveform and current waveform of the inverter must be
symmetrical (Unsymmetrical ratio is less than 10%). Please do not use the
inverter which has unsymmetrical voltage and current waveform, and spike
waveform. The inverter design which can provide the best optical performance,
power efficiency, and lamp life should under the following conditions.
a. The asymmetry rate of the inverter waveform should be less than 10%.
b. The distortion tae of the waveform should be within 2±10%.
c. The inverter output waveform should be better similar to the ideal sine wave.
Ip
I-p
Asymmetry rate = |Ip-I-p| / Irms x 100%

Distortion rate = Ip (or I-p) / Irms
Corporation.
6.3 AC Characteristics
Symbo
Item Min. Typ. Max. Unit Note
l
Rising time tr - - 10 ns (1)
Falling time tf - - 10 ns (1)
High and low level pulse duty tCPH 100 103 - ns CPH1~CPH3
CPH pulse duty tCWH 40 50 60 CPH1~CPH3
STH setup time tSUH 20 - - ns STHR,STHL
STH hold time tHDH 10 - - ns STHR,STHL
STH pulse width tSTH - 1 - tCPH STHR,STHL
STH period tH 61.5 63.5 65.5 µs STHR,STHL
OEH pulse width tOEH - 1.23 - µs OEH
Sample and hold disable time tDIS1 - 8.19 - µs
OEV pulse width tOEV - 4.77 - µs OEV
CKV pulse width tCKV - 3.91 - µs CKV
Clean enable time tDIS2 - 3.90 - µs
Horizontal display timing range tDH - 1440 - tCPH/3
STV setup time tSUV 200 - - ns STVD,STVU
STV hold time tHDV 300 - - ns STVD,STVU
STV pulse width tSTV - 1 - tH STVD,STVU
Horizontal line per field tV 256 262 268 tH (2)
Vertical display start tSV 3 - tH
Vertical display timing range tDV 234 - tH
VCOM Rising time trCOM - 5 µs
VCOM Falling time tfCOM - 5 µs
VCOM delay time tDCOM - 3 µs
RGB delay time tDRGB * 1 µs
Note (1): For all of the logic signals.
Note (2): Please don’t use odd horizontal lines to drive LCD panel for both odd and
even filed simultaneously.
Corporation.
6.4 Timing Diagram of Interface Signal
tCPH
tr tf
tCWH
CPH1
tSUH tHDH
VR,VB,VG
tSTH
tSUH tHDH
STHL(R)
tOEH tDIS1
OEH
Sampling clock timing
STHL(R)
(Input)
STHR(L)
(Output)
CPH1
tDH
1H
HSYNC
OEH tH
STHL(R)
Horizontal display timing range
Corporation.
tOEV
OEV
tDIS2 tCKV
CKV
tDCM
VCOM 90%
VCAC 10%
tfCOM trCOM
BlanK
Black
White White
ViDC
VR,VG,VB ViAC ViA
tDRGB
White
Black
Detail Horizontal timing
The first line

VR,VG,VB
HSYNC
VSYNC
tSV
STVD(U)
VCOM(ODD)
VCOM(EVEN)
Vertical timing
tSTV
STVD(U) tHDV
tSUV Vertical Shift timing
CKV
tCKV
Corporation.
6.5 Power Sequence

Power on
VGH VGH Power off
DVDD
DVDD
GND GND
VGL VGL
Video, Logic Signal

OFF OFF
Level define 90%
10%
Power Sequence: DVDD -> VGL -> VGH
Note Apply the lamp volatge within the LCD operation range. When the back-light turns on
before the LCD operation or the LCD truns off before the back-light turns off.
the display may momentarily become white.
Corporation.
7.0 Reliability test items

No. Item Conditions Remark
o
1 High Temperature Storage Ta=+70 C, 240hrs
o
2 Low Temperature Storage Ta=-20 C, 240hrs
o
3 High Temperature Operation Ta=+60 C, 240hrs
o
4 Low Temperature Operation Ta=-10 C, 240hrs
o
5 High Temperature and High Humidity Ta=+60 C, 90%RH, 240hrs
(operation)
o o
6 Thermal Cycling Test (non operation) -20 C(30min) → +70 C(30min), 200cycles
7 Electrostatic Discharge 200V,200pF(0Ω) 1 time/each terminal
8 Vibration 1.Random:
1.04Grms, 10~500Hz, X/Y/Z,
30min/each direction
2.Sweep sine:
1.5G, 5~500Hr, X/Y/Z,
9 Shock 100G,6ms, ±X, ±Y, ±Z JIS C7021, A-10
3 time for each direction (Condition A)
10 Vibration (with carton) Random:
1.04Grms, 10~500Hz, X/Y/Z
Fixed:
5Hz, 1.5Grms, X/Y/Z
11 Drop (with carton) Height: 60cm JIS Z0202
1 corner, 3 edges, 6 surfaces
Note: There are no display function NG issue occurred, All the cosmetic specification is
judged before the reliability stress.
Corporation.
8.0 OUTLINE DIMENSION U Unit : mm

8.1 Outline Dimension
Corporation.
9.0 LOT MARK

9.1 Lot Mark
10 11 12 13 14 15
code 1,2,3,4,5,6: HannStar internal flow control code.

code 7: production location.
code 8: production year.
code 9: production month.
code 10,11,12,13,14,15: serial number.
Note (1) Production Year

Year 1999 2000 2001 2002 2003 2004 2005 2006 2007 2008
Mark 9 0 1 2 3 4 5 6 7 8
Note (2) Production Month

Month Jan. Feb. Mar. Apr. May. Jun. Jul. Aug. Sep. Oct Nov. Dec.
Mark 1 2 3 4 5 6 7 8 9 A B C
9.2 Location of Lot Mark

(1) The label is attached to the backside of the LCD module.
(2) This is subject to change without prior notice.
HSD070I651
-C00
Rev: 00
Lot mark
Corporation.
10.0 PACKAGE SPECIFICATION

10.1 packing form
(1) Package quantity in one carton: 60 pieces.
(2) Carton size: 464 3 mm 360 3 mm 370 3 mm.
(3) For domestic transportation only.
10.2 packing assembly drawings
Corporation.
11.0 GENERAL PRECAUTION

11.1 Use Restriction
This product is not authorized for use in life supporting systems, aircraft navigation control
systems, military systems and any other application where performance failure could be
life-threatening or otherwise catastrophic.
11.2 Disassembling or Modification

Do not disassemble or modify the module. It may damage sensitive parts inside LCD
module, and may cause scratches or dust on the display. HannStar does not warrant the
module, if customers disassemble or modify the module.
11.3 Breakage of LCD Panel

11.3.1.If LCD panel is broken and liquid crystal spills out, do not ingest or inhale liquid
crystal, and do not contact liquid crystal with skin.
11.3.2. If liquid crystal contacts mouth or eyes, rinse out with water immediately.
11.3.3. If liquid crystal contacts skin or cloths, wash it off immediately with alcohol and
rinse thoroughly with water.
11.3.4. Handle carefully with chips of glass that may cause injury, when the glass is
broken.
11.4 Electric Shock

11.4.1. Disconnect power supply before handling LCD module.
11.4.2. Do not pull or fold the CCFL cable.
11.4.3. Do not touch the parts inside LCD modules and the fluorescent lamp’s connector
or cables in order to prevent electric shock.
11.5 Absolute Maximum Ratings and Power Protection Circuit

11.5.1. Do not exceed the absolute maximum rating values, such as the supply voltage
variation, input voltage variation, variation in parts’ parameters, environmental
temperature, etc., otherwise LCD module may be damaged.
11.5.2. Please do not leave LCD module in the environment of high humidity and high
temperature for a long time.
11.5.3. It’s recommended to employ protection circuit for power supply.
11.6 Operation
11.6.1 Do not touch, push or rub the polarizer with anything harder than HB pencil lead.
11.6.2 Use fingerstalls of soft gloves in order to keep clean display quality, when persons
handle the LCD module for incoming inspection or assembly.
11.6.3 When the surface is dusty, please wipe gently with absorbent cotton or other soft
material.
Corporation.
11.6.4 Wipe off saliva or water drops as soon as possible. If saliva or water drops contact
with polarizer for a long time, they may causes deformation or color fading.
11.6.5 When cleaning the adhesives, please use absorbent cotton wetted with a little
petroleum benzine or other adequate solvent.
11.7 Mechanism
Please mount LCD module by using mouting holes arranged in four corners tightly.
11.8 Static Electricity

11.8.1 Protection film must remove very slowly from the surface of LCD module to
prevent from electrostatic occurrence.
11.8.2. Because LCD module use CMOS-IC on circuit board and TFT-LCD panel, it is very
weak to electrostatic discharge. Please be careful with electrostatic discharge.
Persons who handle the module should be grounded through adequate methods.
11.9 Strong Light Exposure

The module shall not be exposed under strong light such as direct sunlight. Otherwise,
display characteristics may be changed.
11.10 Disposal
When disposing LCD module, obey the local environmental regulations.
Corporation.

HSD070I651

Uploaded by

Document Information

Original Description:

Copyright

Available Formats

Share this document

Share or Embed Document

Sharing Options

Did you find this document useful?

Is this content inappropriate?

Copyright:

Available Formats

HSD070I651

Uploaded by

Copyright:

Available Formats

H a n n Sta r Di sp l a y C o rp .

Document Title HSD070I651 Specification Page No. 1/26

Document No. Revision 1.0

Customer Acceptance Specification

Model : HSD070I651- C00

Document No. Revision 1.0

Document No. Revision 1.0

1.0 General description ……………………………….… p.4

2.0 Absolute maximum ratings …………………………. p.6

3.0 Optical characteristics ………………………………. p.7

4.0 Block diagram …………………………….. ……….. p.11

5.0 Interface pin connection ……………………………. p.12

6.0 Electrical characteristics ……………………………. p.14

7.0 Reliability test items…………………………………… p.21

8.0 Outline dimension …………………………….…… p.22

9.0 Lot mark ……………………………………………... p.23

10.0 Package specification ………………………………. p.24

11.0 General precaution ……………………………………. p.25

Document No. Revision 1.0

1.0 GENERAL DESCRIPTION

1.4 General information

Document No. Revision 1.0

1.5 Mechanical Information

Document No. Revision 1.0

2.0 ABSOLUTE MAXIMUM RATINGS

2.1.2 Back-Light Unit

2.2 Environment Absolute Rating

Item Symbol Min. Max. Unit Note

Document No. Revision 1.0

3.0 OPTICAL CHARACTERISTICS

Document No. Revision 1.0

3.3 Measuring Equipment

Note (1) Definition of Viewing Angle :

Note (2) Definition of Contrast Ratio(CR) :

Luminance with all pixels white

Document No. Revision 1.0

Note (3) Definition of Response Time : Sum of TR and TF

white(TFT OFF) black (TFT ON) white(TFT OFF)

Note (4) Definition of optical measurement setup

Document No. Revision 1.0

Note (5) Definition of brightness uniformity

25% 50% 75%

(Min Luminance of 9 points)

Document No. Revision 1.0

4.0 BLOCK DIAGRAM

LCD Panel Scan

4.2 Pixel Format

480 Pixels(1440 dots)

Document No. Revision 1.0

5.0 INTERFACE PIN CONNECTION

Document No. Revision 1.0

5.2 Back-Light Unit

Document No. Revision 1.0

6.0 ELECTRICAL CHARACTERISTICS

Document No. Revision 1.0

6.2 Back-Light Unit

Note (2) Lamp frequency may produce interference with horizontal

Document No. Revision 1.0

Asymmetry rate = |Ip-I-p| / Irms x 100%

Document No. Revision 1.0

Document No. Revision 1.0

6.4 Timing Diagram of Interface Signal

Sampling clock timing