Ll22 12en Eur Ks Tools LKW Achse
Ll22 12en Eur Ks Tools LKW Achse
www.kstools.com
SPECIAL TOOLS
AXLES - SPECIAL TOOLS
450.0210 450.0241
GREASE CAP PLIERS WHEEL CAP AND AXLE NUT SOCKET
• Hard rubber handle • Internal square drive to DIN 3121 / ISO 1174
• For the damage free drawing off of grease caps • 8-point
• 2x6 moveable adjustable steps • Positive drive of the axle nut
• Wedge shaped jaw profile • Any extensive slipping is avoided
• Head burnished • Milled out profile
• Special tool steel • Sturdy design
• Can be used with an impact wrench or torque wrench
• Special tool steel
Application range: e.g. Volvo axle nut / dust grease caps FM and FH VA (450Nm)
118,90 €
A C Length
mm mm mm
0-100 85,0 500,0
450.0180
VARIO NUT AND CAP KEY SET 13
pcs
186,90 €
• For the dismantling and assembly of vario nuts
• Suitable for exact torque with a 3/4” square drive
• Certain stop through clamping screws and adapter guides on the basic device
• Hole separation maximum 145 mm
• Slim design Spanner width D T Height
• Suitable for narrow spaces mm mm mm mm
• Ideally suited for special nuts and caps
• Special tool steel 115 138,0 45,0 80,0
259,90 € 146,90 €
Spanner width D Height H D1 D2 D3 Number of B T
mm mm mm mm mm mm mm studs mm mm
120,0 158,0 106,0 87,0 109,0 98,0 86,0 6 10,5 20,0
460.1085 460.4450
WRENCH WITH 6 PINS FOR DAF AXLE NUT WRENCH WITH 2 PINS FOR FUSO
• Internal square drive to DIN 3121 / ISO 1174 • Internal square drive to DIN 3121 / ISO 1174
• High accuracy of fit • with 2 external pins, Ø 9.5 mm
• Special profile with 6 internal studs • High accuracy of fit
• Extremely robust version • Extremely robust version
• Suitable for high tightening and loosening torque • Suitable for high tightening and loosening torque
• Special tool steel • Special tool steel
Application range: DAF CF85 transmission (EURO 4 and EURO 5) Application range: IsuzuFuso Canter 3.5 tons
107,90 € 82,90 €
Height D1 D2 D3 Number of B Ø Number of Internal stud Ø Length
mm mm mm mm studs mm mm studs mm mm
55,0 91,0 74,0 66,0 6 6,7 86 2 9,5 68,0
231,90 €
Spanner width Ø Height
mm mm mm
105,0 125,0 85,0
460.4170
AXLE NUT IMPACT SOCKET FOR IVECO
• Internal square drive to DIN 3121 / ISO 1174
• 12 point
• Any extensive slipping is avoided
• Extremely robust version
104,90 €
• Suitable for high tightening and loosening torque
• Can be used with an impact wrench or torque wrench
• Special tool steel
460.4385
AXLE NUT WRENCH FOR FUSO REAR AXLE
• quick-action pin drive
• 8-point
• Extra long execution
• High accuracy of fit
129,90 €
• Extremely robust version
• Suitable for high tightening and loosening torque
• Special tool steel
460.5333
AXLE NUT WRENCH FOR IVECO
• Internal square drive to DIN 3121 / ISO 1174
• 6 point
• High accuracy of fit
• Extremely robust version
• Suitable for high tightening and loosening torque
• Special tool steel
412,90 € 208,90 €
Spanner width Ø Height Spanner width Ø Height
mm mm mm mm mm mm
120 142 360,0 90 117 69,0
Application range: Iveco Euro Cargo Application range: Iveco Eurotech Cursor HA etc.
203,90 € 276,90 €
Spanner width External hexagon Ø Height Spanner width External hexagon Ø Height
mm drive in mm mm mm mm drive in mm mm mm
98,0 36 122,0 115,0 110,0 36 133,0 116,0
450.0200 460.5340
AXLE NUT WRENCH FOR IVECO GROOVED NUT SPANNER SET WITH GUIDE TUBE FOR MAN 2
• Six sided drive 36 mm • Internal square drive to DIN 3121 / ISO 1174 pcs
• Positive drive of the axle nut • including threaded guide tube
• Any extensive slipping is avoided • High accuracy of fit
• Milled out profile • Extremely robust version
• Sturdy design • Suitable for high tightening and loosening torque
• Can be used with an impact wrench or torque wrench • Special tool steel
• Special tool steel
Application range: MAN planetary hub rear axles (5MR, 3MR) and front axle (M series: 3ME DI)
Application range: Iveco Euro Cargo etc.
220,90 €
Spanner width External hexagon External Ø Height Depth
259,90 €
mm drive in mm mm mm mm
98,0 36 122,0 120,0 72,0
460.4165 460.5350
AXLE NUT SOCKET FOR IVECO GROOVED NUT SPANNER SET WITH GUIDE TUBE FOR MAN 2
• Six sided drive 36 mm • Internal square drive to DIN 3121 / ISO 1174 pcs
• 12 point • Screw-in guide tube
• Any extensive slipping is avoided • High accuracy of fit
• Extremely robust version • Extremely robust version
• Suitable for high tightening and loosening torque • Suitable for high tightening and loosening torque
• Can be used with an impact wrench or torque wrench • Special tool steel
• Special tool steel
Application range: Mercedes and MAN, Atego, bus and transporter with grooved nut (A9763560026). The
Application range: Axle nut Iveco Eurotech-Cursor guide tube is not required for the following vehicles: MAN trucks (type H, L, M, N and 1) and bus (type A, J, P
and R) with grooved nut (81.90620-0086)
203,90 €
Spanner width External hexagon Ø Height
259,90 €
mm drive in mm mm mm
105,0 36 128,0 116,0
146,90 € 220,90 €
Internal Ø External Ø Number of Stud width Height
mm mm studs mm mm
77,0 84,0 6 10,0 100,0 450.0161
EXPANDER SLEEVE FOR LOCATION TUBE
• Practical connector system with bayonet clasp
450.0160 • Suitable for groove nut spanner 450.0160
• Enables stable work position
WRENCH WITH 6 PINS FOR MAN AND MERCEDES • Prevents slippage of the socket
• Internal square drive to DIN 3121 / ISO 1174 • Extremely robust version
• Rigid locating tube • Switched by turning the bayonet clasp
• Optional with expander sleeve (bayonet locking system) • Special tool steel
• High accuracy of fit
• Extremely robust version
• Suitable for high tightening and loosening torque
• Special tool steel
Application range: Mercedes Atego Rear axle, Vitaro 814, MAN etc.
84,90 €
231,90 €
Internal Ø External Ø Length
mm mm mm
49,0 57,0 130,0
Internal Ø External Ø Locating tube Number of Internal stud Ø Stud width Height
mm mm Ø mm studs mm mm mm
80,0 95,0 49,0 6 87,0 10,0 185,0 LOCATING TUBE FOR GROOVE NUT SOCKETS
• Practical connector system with fixing screw
• Usably for different groove socket nuts (module systems)
• Enables stable work position
450.0168 • Prevents slippage of the socket
• Extremely robust version
WRENCH WITH 6 PINS FOR MAN AND MERCEDES
• Change through loosening of the grub screw on the hexagon
• Internal square drive to DIN 3121 / ISO 1174 • Special tool steel
• Optional with sleeve locating tube
• High accuracy of fit
• Extremely robust version
• Suitable for high tightening and loosening torque
• Special tool steel
Application range: Mercedes and MAN 10 + 13 t Reduction axle, Hypoid- and Trailer axle NR 7/4, Omnibus
0305 G + 0405 G etc.
288,90 € Internal Ø
mm
External Ø
mm
Length
mm
External Ø Internal Ø D3 Number of Stud width Height Depth
mm mm mm studs mm mm mm 450.0150 46,0 52,0 140,0 € 99,90
115,0 95,0 101 6 6,0 111,0 49,0 450.0152 60,0 67,0 140,0 € 118,90
Application range: MAN TGA Front axle, V9-82L-01(Disk brake/ABS) etc. Application range: MAN with guide tube Ø 66.5 mm: Hypoid rear axles F-series (HY-1175, HDY-1175, HY-
13110, HY-1180). With guide tube Ø 51.5 mm: Rear hub axles F-series (H7, HD7) and front axles F-series
Ø 102 mm
305,90 €
mm mm studs mm mm mm
101,0 110,0 6 93,0 8,0 80,0
450.0175 450.0176
MAN TGA GROOVE NUT SPANNER WITH LOCATING TUBE SLOTTED NUT WRENCH WITHOUT GUIDE TUBE FOR MAN TGA
• Internal square drive to DIN 3121 / ISO 1174 • Internal square drive to DIN 3121 / ISO 1174
• Six point size 60 mm • Six point size 60 mm
• High accuracy of fit • High accuracy of fit
• Extremely robust version • Extremely robust version
• Optional with locating tube • With fixed locating tube
• Suitable for high tightening and loosening torque • Suitable for high tightening and loosening torque
• Special tool steel • Special tool steel
Application range: MAN TGA rear axle, HY-1350 (Hypoid) Application range: MAN TGA rear axle, HY-1350 (Hypoid)
304,90 € 378,90 €
6-point D1 D2 D3 D4 Number of B H1 H2 6-point D1 D2 D3 Number of B H1
mm mm mm mm mm studs mm mm mm mm mm mm mm studs mm mm
60 148,0 133,0 117,0 67,0 6 11,5 98,0 160 60 148,0 133,0 117,0 6 11,0 110,0
460.1035 460.0965
AXLE NUT SOCKET FOR MERCEDES AXLE NUT SOCKET FOR MERCEDES
• Six sided drive 36 mm • Six sided drive 36 mm
• 6 point • 12 point
• Any extensive slipping is avoided • Any extensive slipping is avoided
• Extremely robust version • Extremely robust version
• Suitable for high tightening and loosening torque • Suitable for high tightening and loosening torque
• Can be used with an impact wrench or torque wrench • Can be used with an impact wrench or torque wrench
• Special tool steel • Special tool steel
Application range: Mercedes axle trailers etc. Application range: Mercedes axle trailers etc.
248,90 € 248,90 €
Spanner width 6-point Ø Height Spanner width 6-point Ø Height
mm mm mm mm mm mm mm mm
95,0 36 118 158,0 95,0 36 126,0 157,0
460.5615 460.5370
AXLE NUT WRENCH FOR MERCEDES T-NUTS AND WRENCH SET WITH 4 GUIDE TUBES FOR MERCEDES 5
• Internal square drive to DIN 3121 / ISO 1174 • Internal square drive to DIN 3121 / ISO 1174 pcs
• 6-round profile • including threaded guide tubes
• High accuracy of fit • High accuracy of fit
• Extremely robust version • Extremely robust version
• Suitable for high tightening and loosening torque • Suitable for high tightening and loosening torque
• Special tool steel • Special tool steel
Application range: Mercedes Truck- VA- and Discos Trailer (05.2000) with compact storage HUB Unit Application range: Mercedes Hypoid rear axles HL2/2, HL2/3, HL2/5, HL2/9, HL2/11, HL2/12, HL2/15, HL0/3,
HL0/6, HL0/7, HL1/2 (only Ø 63 mm required), HL1/3, HL1/8, HL1/9, HL2/30C
197,90 € Ø 63 mm
M36 x 1,5 mm
Ø 43 mm
M36 x 1,5 mm M36 x 1,5 mm M36 x 1,5 mm
Ø 40,5 mm Ø 36 mm Ø 42 mm
Spanner width Ø Height
316,90 €
mm mm mm
95 118 75,0
Application range: Mercedes Hypoid rear axles HL2/2, HL2/3, HL2/5, HL2/9, HL2/11, HL2/12, HL2/15 Application range: Mercedes Hypoid rear axles HL2/14, KL2/16, KL4/1, HL4/16, HL4/17, HL4/23, HL4/28,
HL4/29, HL4/30, HL4/4, HL4/8, HD4/6G, HO4/2, HO4/18, NR4/4 and palloid front axles AL3/1, AL3/2, AL3/4,
AL3/7, AL3/8
Ø 63 mm
Ø 75 mm
M36 x 1,5 mm M48 x 1,5 mm
Ø 43 mm M36 x 1,5 mm Ø 51 mm M48 x 1,5 mm
Ø 40,5 mm M36 x 1,5 mm M48 x 1,5 mm M48 x 1,5 mm
Ø 36 mm Ø 43 mm Ø 44 mm Ø 48 mm
259,90 € 344,90 €
460.5625 460.5635
GROOVED NUT SPANNER SET WITH GUIDE TUBE FOR MERCEDES 2 GROOVED NUT SPANNER SET WITH 3 GUIDE TUBES FOR MERCEDES 4
• Internal square drive to DIN 3121 / ISO 1174 pcs • Internal square drive to DIN 3121 / ISO 1174 pcs
• including threaded guide tube • including threaded guide tubes
• High accuracy of fit • High accuracy of fit
• Extremely robust version • Extremely robust version
• Suitable for high tightening and loosening torque • Suitable for high tightening and loosening torque
• Special tool steel • Special tool steel
Application range: Mercedes Hypoid rear axles HL0/3, HL0/6, HL0/7, HL1/2 (only Ø 63 mm necessary), Application range: Mercedes Hypoid rear axles HL2/14, KL2/16, KL4/1, HL4/16, HL4/17, HL4/23, HL4/28,
HL1/3, HL1/8, HL1/9, HL2/30C HL4/29, HL4/30, HL4/4, HL4/8, HD4/6G, HO4/2, HO4/18, NR4/4
Ø 75 mm
M48 x 1,5 mm
Ø 51 mm M48 x 1,5 mm
M48 x 1,5 mm
Ø 63 mm Ø 43 mm
Ø 48 mm
M36 x 1,5 mm
Ø 42 mm
146,90 € 276,90 €
460.5380 460.5630
GROOVED NUT SPANNER SET WITH GUIDE TUBE FOR MERCEDES 2 GROOVED NUT SPANNER SET WITH GUIDE TUBE FOR MERCEDES 2
• Internal square drive to DIN 3121 / ISO 1174 pcs • Internal square drive to DIN 3121 / ISO 1174 pcs
• including threaded guide tube • including threaded guide tube
• High accuracy of fit • High accuracy of fit
• Extremely robust version • Extremely robust version
• Suitable for high tightening and loosening torque • Suitable for high tightening and loosening torque
• Special tool steel • Special tool steel
Application range: Mercedes Hypoid rear axles HL2/2, HL2/7, HL2/13 Application range: Mercedes Palloid front axles AL3/1, AL3/2, AL3/4, AL3/7, AL3/8
Ø 75 mm
Ø 71,5 mm M36 x 1,5 mm M48 x 1,5 mm
Ø 42 mm
231, 90
€
Ø 44 mm
186,90 €
*This is an limited special price offer - only until stocks last.
12 All prices are ex. VAT. With the release of this leaflet all previous prices became invalid. Sold only in specialist stores. Print mistakes, errors and technical alterations excepted. Prices valid up to
31.12.2022
AXLES - SPECIAL TOOLS
460.5395 460.1070
GROOVED NUT SPANNER SET WITH GUIDE TUBE FOR MERCEDES 2 GROOVE NUT WRENCH WITH 6 PINS WITH GUIDE TUBE FOR MERCEDES
• Internal square drive to DIN 3121 / ISO 1174 pcs • Internal square drive to DIN 3121 / ISO 1174
• including threaded guide tube • Rigid locating tube
• High accuracy of fit • High accuracy of fit
• Extremely robust version • Extremely robust version
• Suitable for high tightening and loosening torque • Suitable for high tightening and loosening torque
• Special tool steel • Special tool steel
Application range: Mercedes hypoid axles HO4/10, HO4/10DL, HO4/11DL, HO5/3, HO5/4, HO5/8, HD4/21G, Application range: Mercedes lifting axle
HD4/2G, HD4/22, HD5/3, HL5/2, HL5/6
276,90 €
Ø 88 mm M56 x 1,5 mm
D1 D2 D3 D4 Number of B H1 H2
Ø 57 mm
305,
mm mm mm mm studs mm mm mm
90
€ 115,0 100,0 91,0 46,0 6 11,0 82,0 142,0
460.1075 460.5645
WRENCH WITH 6 PINS FOR MERCEDES GROOVED NUT SPANNER SET WITH GUIDE TUBE FOR MERCEDES 2
• Internal square drive to DIN 3121 / ISO 1174 • Internal square drive to DIN 3121 / ISO 1174 pcs
• High accuracy of fit • including threaded guide tube
• Extremely robust version • High accuracy of fit
• Suitable for high tightening and loosening torque • Extremely robust version
• Special tool steel • Suitable for high tightening and loosening torque
• Special tool steel
220,90 €
D1 D2 D3 Number of B H Ø 100 mm M56 x 1,5 mm
288,90 €
mm mm mm studs mm mm
Ø 59 mm
110,0 96,0 86,0 6 11,0 82,0
460.3790 460.5420
GROOVED NUT WRENCH WITH 6 PINS WITH GUIDE TUBE FOR MERCEDES GROOVED NUT SPANNER SET WITH 3 GUIDE TUBES FOR MERCEDES 4
TRAILER AXLES • Internal square drive to DIN 3121 / ISO 1174 pcs
• Internal square drive to DIN 3121 / ISO 1174 • including threaded guide tubes
• Rigid locating tube • High accuracy of fit
• High accuracy of fit • Extremely robust version
• Extremely robust version • Suitable for high tightening and loosening torque
• Suitable for high tightening and loosening torque • Special tool steel
• Special tool steel
Application range: Mercedes planetary hub rear axles (European axles) 10 tons + 13 tons: HL7/1, HL7/2,
Application range: Mercedes trailer axle TZ5/2 HL7/18, HO7/8, HO7/9, HL7/0, HL7/015, HL7/021, HL7/3, HD7/2,HD7/19DG, HD7/016DG planetary hub front
axle 7 tons: AL7/1
For the NR7/4 planetary hub axles / trailing axle, the base body can be used without a guide tube.
367,90 €
mm mm mm mm studs mm mm mm Ø 50 mm
100,0 82,0 92,0 47,0 6 9,8 142,0 230,0
Application range: Mercedes Actros Rear axle, HL/HL 8 (Hypoid) etc. Application range: Mercedes (2640) drive axle
305,90 € 293,90 €
Internal Ø External Ø Internal
stud Ø
Number of Stud width Height D1 D2 D3 D4 Number of B H1 H2
mm mm mm studs mm mm mm mm mm mm studs mm mm mm
105,0 125,0 115,0 6 10,0 182,0 145,0 125,0 116,0 64,0 6 11,0 84,0 145,0
460.5425 450.0251
GROOVED NUT SPANNER SET WITH 2 GUIDE TUBES FOR MERCEDES 3 SLOTTED NUT WRENCH FOR REAR AXLE NUT FOR MERCEDES
• Internal square drive to DIN 3121 / ISO 1174 pcs • With hexagon drive 32.0 mm
• including threaded guide tubes • For the dismantling and assembly of the rear axle nut
• High accuracy of fit • High accuracy of fit
• Extremely robust version • Sturdy design
• Suitable for high tightening and loosening torque • Suitable for high tightening and loosening torque
• Special tool steel • Drive tube Ø 35 mm
• Special tool steel
Application range: Mercedes rear axle 749.0, trailing rocker arm axle NS4/2, NS4/10 and pinion axles HL6/1,
HL6/2, HL6/3, HD6/3 Application range: Mercedes Citaro
M56 x 1,5 mm
Ø 55 mm
Ø 113 mm
M56 x 1,5 mm
Ø 63 mm
305,90 €
Internal Ø External Ø 6-point Internal Number of Stud width Height
356,
stud Ø
mm mm mm studs mm mm
90 mm
460.0870 460.4205
WRENCH WITH 6 PINS FOR MERCEDES AXLE NUT SOCKET SPANNER FOR MERCEDES
• ideally suited for loosening the rear nut on the differential • Internal square drive to DIN 3121 / ISO 1174
• Internal square drive to DIN 3121 / ISO 1174 • 8-point
• Extremly versatile • High accuracy of fit
• Suitable for exact torque • Extremely robust version
• Special profile with 6 internal studs • Suitable for high tightening and loosening torque
• Suitable for high tightening and loosening torque • For machinery usage
• Special tool steel • Special tool steel
Application range: Axle nut rear axle Mercedes 2636, 2640, 414 (2006 - 2016)
220,90 € 197,90 €
D1 D2 D3 Number of B Height D1 D2 D3 Number of B Height
mm mm mm studs mm mm mm mm mm studs mm mm
135,0 126,0 102,0 6 8,7 103,0 121,0 107,0 98,0 6 12,0 82,0
174,90 €
Spanner width Length
mm mm
77 200,0
460.5455 450.0110
AXLE NUT WRENCH FOR RENAULT AND IVECO AXLE NUT WRENCH FOR SAF
• Internal square drive to DIN 3121 / ISO 1174 • Positive drive of the axle nut
• 6 point • Sturdy design
• High accuracy of fit • Can be used with an impact wrench or torque wrench
• Extremely robust version • Ideally suited for brake restoration working
• Suitable for high tightening and loosening torque • Forward tension with SW 32 mm is at 150 Nm
• Special tool steel • Angle of rotation 20-30° with SW 46
• Special tool steel
197,90 € 158,90 €
Spanner width Ø Height Spanner width 6-point Height
mm mm mm mm mm mm
80 100 137,5 140,0 32 100,0
Application range: Scania front axle (e.g. 124L / 144L), Series 4 from 96 for vehicles above 16 t, removal and
fitting of the axle nuts in front of the brake disc
129,90 € 129,90 €
Spanner width 6-point Ø Height Depth
450.0221 mm mm mm mm mm
125,90 € 141,90 €
Spanner width Ø Height Depth Spanner width Ø Height
mm mm mm mm mm mm mm
80 98,0 75,0 25,0 95,0 117,0 82,0
460.1365 460.1370
AXLE NUT WRENCH FOR SCANIA AXLE NUT WRENCH FOR SCANIA
• for mounting and dismounting Scania axle nuts • for mounting and dismounting Scania axle nuts
• Internal square drive to DIN 3121 / ISO 1174 • Internal square drive to DIN 3121 / ISO 1174
• 8-point • 8-point
• High accuracy of fit • High accuracy of fit
• Extremely robust version • Extremely robust version
• Suitable for high tightening and loosening torque • Suitable for high tightening and loosening torque
• For machinery usage • For machinery usage
• Special tool steel • Special tool steel
Application range: Axle nut Scania and Fuso front axle Application range: Removal and installation of the axle nut of Scania rear axle
110,90 € 141,90 €
Spanner width Ø Height Spanner width Ø Height
mm mm mm mm mm mm
80,0 103,0 94,0 100,0 123,0 84,0
188, 90
€ 460.1415
mm
95,0
mm
125,0
Ø mm
60,0
mm
350,0
mm
40,0 € 367,90
D1 D2 D3 Number of B Height 460.0680 105,0 135,0 60,0 355,0 40,0 € 401,90
mm mm mm studs mm mm
87,0 76,0 70,0 4 6,5 145,0
460.5440
AXLE NUT WRENCH FOR SETRA AND KÄSSBOHRER
450.0236 • Six sided drive 36 mm
8-PIN T-NUTS WRENCH FOR SCANIA • 6 point
• High accuracy of fit
• With 3/4“ square drive to DIN 3121 / ISO 1174 • Extremely robust version
• Special profile with 8 external studs • Suitable for high tightening and loosening torque
• Positive drive of the axle nut • Special tool steel
• Any extensive slipping is avoided
• Milled out profile
• Sturdy design
• Can be used with an impact wrench or torque wrench
• Special tool steel
Application range: Scania 420 (heavy duty tipper axis) removal and
installation of the mounting nut on the axle bearing
339,90 €
238,90 € Spanner width External
mm hexagon
Length
mm
D1 D2 D3 Number of B Height Depth 105 36 mm 400,0
mm mm mm studs mm mm mm
119,0 90,0 103,0 8 9,5 100,0 75,0
CLAMP NUT SOCKET
• Internal square drive to DIN 3121 / ISO 1174
450.0245 • For professional loosening and tightening
• Extremly versatile
AXLE NUT WRENCH FOR VOLVO • Rectangular form
• Internal square drive to DIN 3121 / ISO 1174 • Usably with rectangular clamp nuts on the axle stub
• 6 point • Milled out profile
• Slim design • Suitable for high tightening and loosening torque
• Sturdy design • For machinery usage
• Positive drive of the axle nut • Special tool steel
• Any extensive slipping is avoided
• Milled out profile
• Can be used with an impact wrench or torque wrench
• Special tool steel
Application range: Axle nut Volvo FH front axle cover, steering pin (e.g. FM 12)
124,90 € 460.5471
460.5472
41,0
46,0
50,0
52,0
€
€
73,90
84,90
Spanner width Ø Height Depth
mm mm mm mm 460.5473 50,0 62,0 € 93,90
80 100,0 55,0 17,0 460.5474 56,0 68,0 € 99,90
150.1467
THREAD BOTTOM TAP FOR EXTERNAL THREAD M4 - M45
• For re-cutting and cleaning damaged outer threads
• No damage of the thread
• Suitable for right and left-handed thread
• steplessly adjustable via knurled screw
• The chaser is well-guided due to the width of the jaw and does not tilt
• Can be used everywhere regardless of the thread length
• Simple handling
• cutting of HSS steel with hardness 55-60
56,90 €
150.1435
THREAD REPAIR KIT FOR INTERNAL AND EXTERNAL THREADS 6
• For re-cutting and cleaning of internal and external threads pcs
• Suitable for right and left handed threads up to Ø 140mm
• Quick cutting jaw modification possible from the magazine
• No damage of the thread due to the soft holding guides
• With 3 x die for commercial vehicle hub nut threads
• Special tool steel
• In durable plastic storage case
Chaser metric: 1.0 - 1.25 -1.5 -1.75 -2.0 -2.5 -3.0 -3.5 mm
Chaser imperial: 24-20-18-16-14-12-11.5-11-10-9-8-7.5-7-6-5-4 pitch
Thread file metric 0.8-1.0-1.25 -1.5-1.75-2.0-2.5-3.0 mm
Thread file, imperial 24-20-18-16-14-12 -11-10
Die: M18x1.5 / M20x1.5 / M22x1.5
Application: Trucks, land and construction machines, municipally and forestery technology on e.g. axle threads,
hydraulic cylinder screw joints, steering and push rods
367,90 €
*This is an limited special price offer - only until stocks last.
18 All prices are ex. VAT. With the release of this leaflet all previous prices became invalid. Sold only in specialist stores. Print mistakes, errors and technical alterations excepted. Prices valid up to
31.12.2022
AXLES - SPECIAL TOOLS
460.3700 460.0685
UNIVERSAL COMMERCIAL VEHICLE WHEEL HUB EXTRACTOR SET 5 WHEEL HUB PULLER FOR MAN 2
• variable use for bolt circle diameters up to 190 mm pcs • Suitable for removing the wheel hub pcs
• Sturdy design • For 166 mm hole diameters
• Trapezoidal threaded spindle for high pull-off force • Sturdy design
• Special tool steel • Trapezoid thread spindle for high removal power - drive 30 mm
• Special tool steel
Ø 166 mm
401,90 € 514,90 €
460.1765
UNIVERSAL COMMERCIAL VEHICLE WHEEL HUB EXTRACTOR SET 27
• Variable use for bolt circle diameter 110 mm - 448 mm pcs
• Universal use for bolts up to max. Ø 30 mm
• With 2 rods and trapezoid thread spindle
• With 3 pressure pieces
• Includes 5 thread adaptor sets
• Special tool steel
1029,90 €
UNIVERSAL WHEEL HUB PULLER
• Extracting the wheel hubs and/or housing over the grease cap thread
• Six sided drive enable unscrewing on the cap
• Sturdy design
• Trapezoid thread spindle for high removal power - drive 30 mm
• Special tool steel
1189,90 € 390,90 €
460.3795
ASSEMBLY AND DISASSEMBLY TOOL SET FOR ZF AXLES 11
• ideally suited for mounting and dismounting wheel hubs with compact bearings pcs
• can also be used with fixed wheel hubs
• for damage-free mounting of the shaft sealing rings
• for mounting the bellows with installed brake calliper
• Special tool steel
1529,90 €
*This is an limited special price offer - only until stocks last.
20 All prices are ex. VAT. With the release of this leaflet all previous prices became invalid. Sold only in specialist stores. Print mistakes, errors and technical alterations excepted. Prices valid up to
31.12.2022
AXLES - SPECIAL TOOLS
440.0025 440.0480
PRESSURE AND PULL HYDRAULIC CYLINDER SET 32T 6 PRESSURE AND PULL HYDRAULIC CYLINDER SET 7
• Optimal for universal use in car garages pcs • Optimal for universal use in car garages pcs
• Suitable for both pressure and train uses • Suitable for both pressure and train uses
• With magnetic centring adapter • Extremely high and uniform power construction
• Extremely high and uniform power construction • Industrial execution with forged piston
• Industrial execution with forged piston max. • Pressure of the hydraulic cylinders can be combined with the impact body max.
32t 45t
• Pressure of the hydraulic cylinders can be combined with the impact body with impact force during use
with impact force during use • With automatic piston return
• Universal usage with reduction M10-M22 • Ideally used with transporters and commercial vehicles
• Ideally used with transporters and commercial vehicles • Special tool steel
• With automatic piston return
• Special tool steel
• In durable steel storage case
ORIGINAL
ORIGINAL *CEJN® 390x260x680 mm 320x150x200 mm
*CEJN®
2,2 m
m
2,2
QUICK COUPLING -
DRIP FREE!
750 ml
1,4 L
OPTIONAL OPTIONAL
QUICK COUPLING -
440.0063 440.0063 DRIP FREE!
i i
769,90 € 832,90 €
*This is an limited special price offer - only until stocks last.
All prices are ex. VAT. With the release of this leaflet all previous prices became invalid. Sold only in specialist stores. Print mistakes, errors and technical alterations excepted. Prices valid up to
31.12.2022
21
AXLES - SPECIAL TOOLS
440.0063
MANOMETER
• With Cejn quick coupling for direct coupling to all KS Tools hydraulic pumps
• With easy-to-read scale in psi and bar
Quick coupling -
drip free!
191,90 €
440.0585
HYDRAULIC UNIT 32 T, WITH HYDRAULIC PUMP AND MANOMETER 11
• Optimal for universal use in car garages pcs
• Includes hydraulic pump and manometer
• Suitable for both pressure and train uses
• With magnetic centring adapter
max.
• Extremely high and uniform power construction
32t
2,2 m
750 ml
ORIGINAL *CEJN®
390x260x680 mm 2039,90 €
440.9996
HYDRAULIC UNIT 32-TONNES, WITH AIR HYDRAULIC PUMP 9
• Optimal for universal use in car garages pcs
• Suitable for both pressure and train uses
• With magnetic centring adapter
• Extremely high and uniform power construction
max.
• Industrial execution with forged piston
• Pressure of the hydraulic cylinders can be combined with the impact body with impact force during use
• With pneumatic hydraulic pump
QUICK COUPLING - 32t
ORIGINAL *CEJN®
OPTIONAL
440.0063
i 1,4 L
320x150x200 mm 2209,90 €
*This is an limited special price offer - only until stocks last.
22 All prices are ex. VAT. With the release of this leaflet all previous prices became invalid. Sold only in specialist stores. Print mistakes, errors and technical alterations excepted. Prices valid up to
31.12.2022
AXLES - SPECIAL TOOLS
440.0038 440.0036
KLANN HYDRAULIC TO KS MODULO 2-TOOL KS HYDRAULIC MODULO 2 TO KLANN TOOLS
• For using the Klann hydraulic cylinder (17 t) with KS Tools tool 1.1/2” internal thread • For use with the KS Tools hydraulic cylinder MODULO 2 (8.5-22 t) with Klann special tool
• Adapter 2.1/4”-14 UNS (Klann thread) to 1.1/2” MODULO 2 • Adapter 1.1/2” MODULO 2 to 2.1/4”-14 UNS (Klann thread)
• Special tool steel • Special tool steel
2.1/4“-14 UNS
1.1/2“-11
61,90 € 61,90 €
440.0409 440.0034
KS HYDRAULIC MODULO 2 TO KLANN (COMMERCIAL VEHICLES-SPECIAL TOOLS) KS HYDRAULIC MODULO 2 TO SAUER, MÜLLER, KS MODULO 1 TOOLS
• For using the KS tools hydraulic cylinder MODULO 2 (32t) with the Klann special tool (connection 2.3/4”-16 • For use of the KS Tools hydraulic cylinder MODULO 2 (8,5-22 t) with Sauer-, Müller-, KS MODULO 1 special
UNS) tools
• Adapter 2.1/2” MODULO 2 to 2.3/4”-16 UNS (Klann thread) • Adapter 1.1/2” MODULO 2 to 2.1/4”-16 UN (Sauer, Müller, KS MODULO 1)
• Special tool steel • Special tool steel
2.1/2“ 1.1/2“-11
2.1/4“-16 UN
2.3/4“-16 UNS
67,90 € 61,90 €
440.0407 440.0408
PASCHKE HYDRAULIC TO KS MODULO 2 TOOLS KS HYDRAULIC TO PASCHKE TOOLS
• For using the Paschke hydraulic cylinder with KS Tools special tools MODULO 2 • For using the Paschke KS Tools hydraulic cylinder MODULO 2 (8,5-22 t) with Paschke special tools
• Adapter M68x2 mm (Paschke thread) to 1.1/2” MODULO 2 • Adapter 1.1/2“ MODULO 2 auf M68x2 mm (Paschke thread)
• Special tool steel • Special tool steel
M68x2
1.1/2“-11
M68x2
1.1/2“-11
93,90 € 67,90 €
440.0037
KS HYDRAULIC MODULO 2 TO KS COMMERCIAL VEHICLES-SPECIAL TOOLS
• For use with hydraulic cylinder MODULO 2 (16 and 22 t) to KS Tools tools MODULO 2 with 2.1/2“ thread
• Adapter 1.1/2“ MODULO 2 to 2.1/2“ thread MODULO 2 (large traverse - commercial vehicles)
• Special tool steel
1.1/2“-11
2.1/2“-11 UN
36,90 €
*This is an limited special price offer - only until stocks last.
All prices are ex. VAT. With the release of this leaflet all previous prices became invalid. Sold only in specialist stores. Print mistakes, errors and technical alterations excepted. Prices valid up to
31.12.2022
23
AXLES - SPECIAL TOOLS
440.0590 440.0490
WHEEL HUB PULLER SET FOR 8 AND 10 BOLTS FOR 32 T 11 PULLER SET FOR HUB WITHOUT WHEEL STUD RIM FOR 32 T 3
• for disassembly of truck wheel hubs with 8 or 10 bolts (275 mm / 335 mm) pcs • for the effective pressing out of firmly rusted bearings with external hubs of straight shafts pcs
• Use in conjunction with 32t hydraulic cylinder (440.0025) with impact function • Minimum work time
• ideal for pressing out wheel hub with compact bearing • Secure and easy to use
• Sturdy design • Special tool steel
• Secure and easy to use max.
32t
• ideal for use with wheel bearing set for Scania (440.0375) Recommended hydraulic cylinder: 32 t (440.0025)
• Special tool steel
• In durable plastic storage case Application range: Mercedes Atego, Actros, MAN TGA, TGS, TGX, Volvo FL, Renault Kerax, Magnum, Midlum,
Premium and all brands with the same bolt arrangement
Recommended hydraulic cylinder: 32t (440.0025)
548,90 €
440.0495
HUB PULLERS FOR LOW TRAILERS FOR 32 T AND 45 T 15
pcs
1244,90 €
• for pressing out the 225 mm hub with 10 screws
• Hubs with unit bearings on straight shafts can be released in this way
• Use in connection with threaded plate (440.0593)
• Sturdy design
• Secure and easy to use
440.0365 • Special tool steel
SPACER SCREW M22 FOR WHEEL HUB PULLER SET (440.0590) Recommended hydraulic cylinder: 32 t (440.0025) and 45 t (440.0480)
• for extending the pressure rod
• ideal for axles with hub planetary gear in the wheel hub
• Special tool steel
440.0610
WHEEL HUB PULLER SET FOR 8 AND 10 BOLTS FOR 45 T
• for disassembly of truck wheel hubs with 8 or 10 bolts (275 mm / 335 mm)
12
pcs
786,90 €
• Use in conjunction with 45t hydraulic cylinder (440.0480) with impact function
• ideal for pressing out wheel hub with compact bearing 440.0615
• Sturdy design
• Secure and easy to use
• ideal for use with wheel bearing set for Scania (440.0375)
max.
45t
PULLER SET FOR HUB WITHOUT WHEEL STUD RIM FOR 45 T 3
• for the effective pressing out of firmly rusted bearings with external hubs of straight shafts pcs
• Special tool steel
• Minimum work time
• In durable plastic storage case
• Secure and easy to use
• Special tool steel
Recommended hydraulic cylinder: 45t (440.0480)
Recommended hydraulic cylinder: 45t (440.0480)
Application range: Mercedes Atego, Actros; MAN TGA, TGS, TGX; Volvo FL; Renault Kerax, Magnum, Midlum,
Premium and all brands with the same bolt arrangement
1244,90 € 514,90 €
*This is an limited special price offer - only until stocks last.
24 All prices are ex. VAT. With the release of this leaflet all previous prices became invalid. Sold only in specialist stores. Print mistakes, errors and technical alterations excepted. Prices valid up to
31.12.2022
AXLES - SPECIAL TOOLS
450.0080 605.0005
BEARING ASSEMBLY AND DEASSEMBLY TOOL SET 5 SEPARATOR SET INCLUSIVE WITH YOKE Ø 30,0 - 220,0 MM 3
• Can be used manually with a hammer or workshop press pcs • For the removal of secure bearings and bushes pcs
• Optimal placing through the pressure plates • Extremely robust spindle with inductively hardened thread
• For easy and damage free assembly • Hydraulic thrust spindle available
• For the correct dismantling and assembly of bearings • Special tool steel
• Suitable for commercial, agricultural engineering and construction machines • In durable steel storage case
• Forged, robust execution
• Special tool steel
• In durable plastic storage case
429,90 € 1064,90 €
460.1380
MAN WHEEL BEARING PULLER 10
• Ideally suited to the removal of old wheel bearings pcs
• Sturdy design
• Trapezoid thread spindle for high removal power - drive 30 mm
• Special tool steel
Application range: MAN 33460, 410 and 414 -break disc bearing front axle
30 mm
Ø 108 mm
860,90 €
*This is an limited special price offer - only until stocks last.
All prices are ex. VAT. With the release of this leaflet all previous prices became invalid. Sold only in specialist stores. Print mistakes, errors and technical alterations excepted. Prices valid up to
31.12.2022
25
AXLES - SPECIAL TOOLS
D1 D2 D3 H1 H2
mm mm mm mm mm
460.4375 61,5 69,5 124,5 22,6 35,0 € 82,90
460.4370 73,5 81,5 137,5 22,6 35,0 € 84,90
460.4380 91,5 99,5 147,5 22,6 35,0 € 93,90
D1 D2 D3 H1 H2
mm mm mm mm mm
460.4005 51,0 58,0 109,0 21,0 34,0 € 56,90
565,90 €
460.4130
WHEEL BEARING PULLER SET FOR SCANIA 14
• ideally suited for removing stuck wheel bearings pcs
D1 D2 D3 H1 H2 • Sturdy design
mm mm mm mm mm • Threaded spindle for high pull-off force - 30.0 mm drive
• Special tool steel
460.4000 61,0 68,0 124,0 21,0 34,0 € 61,90
Application range: Scania rear axle
D1 D2 D3 H1 H2
758,90 €
mm mm mm mm mm
460.3995 83,0 94,0 148,0 26,0 40,0 € 99,90
Ø 24 mm
Ø 34 mm
Ø 47 mm
Ø 47 mm
Ø 47 mm
Ø 39 mm Ø 50 mm Ø 61 mm Ø 95 mm
Technical data:
Capacity: 75 t
Stroke: 160,0 mm
Operating pressure max:
Volume:
700 bar
1,8 l 4990,00 €
*This is an limited special price offer - only until stocks last.
All prices are ex. VAT. With the release of this leaflet all previous prices became invalid. Sold only in specialist stores. Print mistakes, errors and technical alterations excepted. Prices valid up to
31.12.2022
27
AXLES - SPECIAL TOOLS
500.8480
INDUCTION HEAT GUN SET 6
• For loosening rusted and seized connections pcs
• For loosening “insoluble” glued connections
• Induction principle
• Pinpoint heating in seconds
• Heating of components up to max. 790 °C (red-hot)
Application range: Screws, nuts and bolts, exhaust clamps and pipes,
lambda probes, running gear, stuck bearings, ball joints, steering
(e.g. tracking adjustment screws), chemically micro-encapsulated threaded
connections (bonded), warming of bearing housings during dismantling and assembly
451,90 €
1.00
0 W
Ø 30 mm Ø 40 mm
160 mm 170 mm
750 mm
Ø 50 mm Ø 56 mm
160 mm 120 mm
36,90 € 36,90 €
Ø Length Capacity Ø Length Capacity
mm mm mm mm
57,0 370,0 400 g 57,0 350,0 400 g
980.1021
TWO-HAND GREASE GUN
• For working with grease up to NLGI2
• Grease gun piston diameter 10.0 mm
• Quick and easy cartridge replacement
• Clean and complete emptying of the cartridge
• Fill levels can be checked at all times
• Ergonomic anti-slip handle
Technical data:
Connection thread: M10 x 1,0
Operating pressure: 400 bar
Burst pressure system (bar): 850 bar
Burst pressure grease gun head (bar): 1200 bar
NLGI class: <2
Output per stroke cm³: 2,10
82,90 €
mm mm Capacity
515.3900
PNEUMATIC GREASE GUN FOR STROKE BY STROKE CONVEYANCE OF GREASE
• Air exhaust through the handle
• For one handed operation with balanced ergonomic design
• For cartridges and buckets and/or also for loose grease
• Includes flexible hose and nozzle
• Includes 1/4” coupling connector
• Grease feeding: one stroke per trigger actuation
Technical data:
Output pressure: 260 bar
Connection thread: 1/4”PT
Output per stroke cm³: 1,30 cm³
Air consumption: 170 l/min
Operating pressure: 6,3 bar (90 psi)
Width Length
61,90 €
mm mm Capacity
980.1014
36,90 €
NOZZLE EXTENSION
• Made from metal
• Includes four-jaw nozzle
• For use with the manually operated grease gun
Connection Length Height
thread mm mm
1/8”PT 74,0 38,0
980.1100
7
6,90 €
GREASE GUN ADAPTOR SET
• For standard hand, cordless and pneumatic grease guns pcs
• Adaptor with sliding sleeve for break-proof connection
• Straight and angled grease nipple
Connection Length • For grease nipples out of steel, brass and stainless steel
thread mm
1/8”PT 160,0 Application range: Cone, funnel, ball and flat grease nipples
980.1013
NOZZLE
• Made from metal
• Four-jaw nozzle
• For use with the manually operated grease gun
5,90 €
Connection
50,90 €
thread
1/8”PT
460.1210 440.0190
BEARING LUBRICATION AID PRESS TOOL
• Ideally suited to greasing the bearings • Forged press tool for removing the ball joints and
• The grease is pressed through the rollers/barrels by pressing down on the piston stabiliser ball pins
• For 150-200 mm bearing diameter • Maximum force 16 t
• Permanently lockable • Ideal for use with a hydraulic cylinder
• With triple sealing against grease leaks • Optimally used with ball joint sets 440.0230 and
• Residual grease is protected against dust and oxidation 440.0240 as well as stabiliser ball pin set 440.0235
• Aluminium • Secure and easy to use
• Extremly versatile • Minimum work time
• Special tool steel
735,90 €
Width Height
259,90 €
mm mm
240,0 240,0
440.0730 440.0015
PRESSURE AND PULL HYDRAULIC CYLINDER SET, 8.5T 4 SHORT-STROKE HYDRAULIC CYLINDER SET 14T 3
• For the assembly and disassembly of silent bearings, steering pin bolts, wheel bearings etc. pcs • For the assembly and disassembly of silent bearings, steering pin bolts, wheel bearings etc. pcs
• Can be used in the narrowest of spaces • With adjustable pressure rod
• With adjustable pressure rods and impact body • Maximum pressure with little effort
• With automatic piston return • Especially for use with press tool and press stand 440.0190 and 440.0180
• Special tool steel max. • With automatic piston return max.
8,5t 14t
• Special tool steel
503,90 €
*This is an limited special price offer - only until stocks last.
All prices are ex. VAT. With the release of this leaflet all previous prices became invalid. Sold only in specialist stores. Print mistakes, errors and technical alterations excepted. Prices valid up to
31.12.2022
31
AXLES - SPECIAL TOOLS
515.3880
VIBRO IMPACT PNEUMATIC CHISEL HAMMER SET 6
• With non slip soft grip handle pcs
• Air exhaust through the handle
• Ergonomic designed handle
• Ideal for industry
• Efficient, gentle loosening of screw fittings
• With stepless impact regulation
• Vibration dampened
• Cold insulated handle
• Includes 1/4” coupling connector
• Ultra light housing from two component plastic
369,90 €
150.1608
IMPACT TIE ROD TOOL
• Vibration supported release of tracking rods, contoured screws or screws in the axle area etc.
• Adjustable in connection with a pneumatic chisel hammer
• The special vibrating mandrel applies an impact pulse to the screw connection to be loosened,
thereby loosening rust and supporting the loosening process
• Pneumatic chisel adapter (10 mm) for use with pneumatic chisel hammers on the market
• Utilisation of vibration and shock pulse of Vibro Power pneumatic hammer
• Special tool steel
Application: Cutting exhausts, loosening of ball joint, extracting bolts and cutting metal sheets
56,90 € 25,90 €
Width Height Length Drive Ø Length Drive in
mm mm mm mm mm mm
40,0 130,0 68,0 Ø 10 mm 6,5 177,0 10 mm
Application range
VIBRO-IMPACT SHEET METAL CUTTING TOOL WITH ANTI-ROTATION DEVICE 515.3967 20,0 € 36,90
• Suitable for use with industry-standard percussion hammers (10.0 mm holder) 515.3968 24,0 € 36,90
• Universal use for bodywork and chassis repair
• Extension of the working range 515.3969 35,0 € 36,90
• Utilisation of vibration and shock pulse of Vibro Power pneumatic hammer
• Robust chisel forged out of one piece
• Special tool steel
515.4880
Application: Cutting exhausts, loosening of ball joint, extracting bolts and cutting metal sheets
HIGH-PERFORMANCE VIBRO-IMPACT PNEUMATIC CHISEL HAMMER
• With non slip handle
• Air exhaust through the handle
• Ergonomic designed handle
515.3965
VIBRO-IMPACT FLAT CHISEL WITH ANTI-ROTATION DEVICE
• Suitable for use with industry-standard percussion hammers (10.0 mm holder)
• Universal use for bodywork and chassis repair
• Extension of the working range
• Utilisation of vibration and shock pulse of Vibro Power pneumatic hammer
• Robust chisel forged out of one piece
• Special tool steel
Application: Cutting exhausts, loosening of ball joint, extracting bolts and cutting metal sheets
Technical data:
Chisel holder: 15 mm
Number of blows: 2500 blows/min
36,90 €
Vibration acceleration: 20,4 m/s²
Noise performance level: 115 dbA
Noise pressure level: 104 dbA
Air consumption: 210 l/min
860,90 €
Width Length
mm mm Operating pressure: max. 6,3 bar (90 psi)
Connection thread: 1/4”NPT
19,0 190,0
515.3966 515.4881
VIBRO-IMPACT HALF-ROUND CHISEL WITH ANTI-ROTATION DEVICE VIBRO-IMPACT TIE ROD REMOVER
• Suitable for use with industry-standard percussion hammers (10.0 mm holder) • Pneumatic chisel adapter (15 mm) for use with pneumatic chisel hammers on the market
• Universal use for bodywork and chassis repair • Extension of the working range
• Extension of the working range • Utilisation of the vibration and impact impulse of the high-performance vibro-impact
• Utilisation of vibration and shock pulse of Vibro Power pneumatic hammer • Robust chisel forged out of one piece
• Robust chisel forged out of one piece • Special tool steel
• Special tool steel
Application: Cutting exhausts, loosening of ball joint, extracting bolts and cutting metal sheets
36,90 € 197,90 €
Width Length Width Length
mm mm mm mm
26,0 195,0 45,0 295,0
99,90 €
Width Length
mm mm
24,0 290,0
515.4883
VIBRO-IMPACT HAMMER INSERT
• Pneumatic chisel adapter (15 mm) for use with pneumatic chisel hammers on the market
• Extension of the working range
• Utilisation of the vibration and impact impulse of the high-performance vibro-impact
• Robust chisel forged out of one piece
• Special tool steel
369,00 €
150.9710
174, 90
€ UNIVERSAL BEARING AND BUSH DRIVER SET
• for gentle driving of bearing and radial sealing rings
21
pcs
• Universal applicable range
Width Length
mm mm • Can be used manually with a hammer or workshop press
• Applications from 70.0 - 150.0 mm
45,0 295,0 • Pressure plates are for the two driving spindles
• Special tool steel
• In durable plastic storage case
515.4884
VIBRO-IMPACT POINTED CHISEL, XL
• Pneumatic chisel adapter (15 mm) for use with pneumatic chisel hammers on the market
• Extension of the working range
• Utilisation of the vibration and impact impulse of the high-performance vibro-impact
• Robust chisel forged out of one piece
• Special tool steel
82,90 €
Length
mm
290,0
735,90 €
515.4885 700.1760
VIBRO-IMPACT CONCAVE INSERT
• Pneumatic chisel adapter (15 mm) for use with pneumatic chisel hammers on the market
PRESS AND PULL SLEEVE SET 20
• For the assembly and disassembly of bearings pcs
• Extension of the working range
• Utilisation of the vibration and impact impulse of the high-performance vibro-impact • Ideally for silent bearings, hydro bearings, bushings, ball bearings, simmer rings etc.
• Robust chisel forged out of one piece • Universal use for passenger cars, trucks, communal, agricultural and forest vehicles
• Special tool steel • Outstanding to use also in connection with workshop press or hollow piston cylinder
• According to use application the sheaths individually can be reworked
• Pressure bearing protects against increased friction during the process
• In durable plastic storage case
186,90 € Attention: the spindles need to be greased with a good lubricant for each application! Do not overload spin-
dles, otherwise the thread lengthens and the pitch of the nut and spindle no longer match. The result: the nuts
will seize up. Always check the applied force at the drive with a torque wrench!
Width Length
mm mm Maximum permitted torque:
45,0 295,0 Spindle M10x1,5 60 Nm
Spindle M12x1,5 100 Nm
Spindle M14x1,5 180 Nm
Spindle M16x1,5 250 Nm
515.4886
VIBRO-IMPACT DRIFTERS
• Pneumatic chisel adapter (15 mm) for use with pneumatic chisel hammers on the market
• Extension of the working range
• Utilisation of the vibration and impact impulse of the high-performance vibro-impact
• Robust chisel forged out of one piece
• Special tool steel
99,90 €
Width Length
514,90 €
mm mm
20,0 225,0
Caution: The spindles must be greased before first use! Overloading leads to unwanted material stresses or Attention: the spindles need to be greased with a good lubricant for each application! Do not overload spin-
breakage Always check the power settings on the drive with a torque wrench Not to be combined with other dles, otherwise the thread lengthens and the pitch of the nut and spindle no longer match. The result: the nuts
systems will seize up. Always check the applied force at the drive with a torque wrench!
299,90 € 843,90 €
Attention: the spindles need to be greased with a good lubricant for each application! Do not overload spin-
dles, otherwise the thread lengthens and the pitch of the nut and spindle no longer match. The result: the nuts
will seize up. Always check the applied force at the drive with a torque wrench!
894,90 €
700.1810
MASTER COMPRESSION AND TENSION SLEEVE SET 46
• For the assembly and disassembly of bearings pcs
• Ideally for silent bearings, hydro bearings, bushings, ball bearings, simmer rings etc.
• Universal use for construction machines, truck, municipally, country and forestery technology etc.
• Outstanding to use also in connection with workshop press or hollow piston cylinder
• According to use application the sheaths individually can be reworked
• Pressure bearing protects against increased friction during the process
• In durable plastic storage case
Attention: the spindles need to be greased with a good lubricant for each application! Do not overload spin-
dles, otherwise the thread lengthens and the pitch of the nut and spindle no longer match. The result: the nuts
will seize up. Always check the applied force at the drive with a torque wrench!
1244,90 €
Spindle M12x1,5 100 Nm
Spindle M14x1,5 180 Nm
Spindle M16x1,5 250 Nm
Spindle TR20x4 400 Nm
700.1735
SPINDLE SET FOR PRESS AND PULL SLEEVE SET 13
• With 4 spindles for KS press and pull sleeve set pcs
• Thread lead: 1.5
• Pressure bearing protects against increased friction during the process
• Incl. special thread grease
• Chrome molybdenum
Attention: the spindles need to be greased with a good lubricant for each application! Do not overload spin-
dles, otherwise the thread lengthens and the pitch of the nut and spindle no longer match. The result: the nuts
will seize up. Always check the applied force at the drive with a torque wrench!
441,90 € 2377,90 €
*This is an limited special price offer - only until stocks last.
36 All prices are ex. VAT. With the release of this leaflet all previous prices became invalid. Sold only in specialist stores. Print mistakes, errors and technical alterations excepted. Prices valid up to
31.12.2022
AXLES - SPECIAL TOOLS
980.1090 460.3755
SPECIAL THREAD GREASE FOR PULLER AND PUSHER SPINDLES UNIVERSAL TENSION SLEEVE SET WITH HYDRAULIC CYLINDER 18 T 24
• Lubricant for components subjected to high static loads, e.g. threaded spindles • For the assembly and disassembly of bearings pcs
• Prevents excessive wear and seizing • ideal for silent bearings, hydromounts, bushings, ball bearings, oil seals, etc.
• Irregularities in the surface to be protected are completely filled • universal design for construction machines, trucks, municipal, agricultural and forestry technology, etc.
• Minimises the friction thanks to the closed surface • for use with supplied hydraulic cylinder
• Effective protection against corrosion • Sturdy design
• Increases the service life of threaded spindles • Special tool steel
• Ensures reliable function even at high temperatures up to max. 1200°C
2,90 €
1589,90 €
980.1085
SPECIAL THREAD GREASE FOR PULLER AND PUSHER SPINDLES AND NUTS 460.3925
SUBJECTED HIGH LOADS
• Lubricant for components subjected to high static loads, e.g. threaded spindles
DOUBLE WISHBONE BUSHES SET FOR DAF Ø 70 MM 8
• Prevents excessive wear and seizing • For mounting and dismounting the bushings on the wishbone of the rear axle pcs
• Irregularities in the surface to be protected are completely filled • Suitable for the front bearing and for the rear bearings with Ø 70mm
• Minimises the friction thanks to the closed surface • Secure and easy to use
• Effective protection against corrosion • In conjunction with a workshop press
• Increases the service life of threaded spindles • Special tool steel
• Ensures reliable function even at high temperatures up to max. 1200°C
Application range: DAF wishbone at the rear axle
10,90 €
ASSEMBLY SLEEVES FOR SLOTTED SILENT BEARINGS ON COMMERCIAL
VEHICLES
• Allows the pretensioning of slotted silent bearings on commercial vehicles
• Adaptor for original dimension to intake bore size with conical sleeve
• Universal solution
• For use with hydraulic and / or mechanical press tools
• Press the sleeve directly on the intake of the vehicle is possible
• Contains a selection of the most common diameters
• Polished inside wall for optimum sliding
• Sturdy design
• Low dimension
684,90 €
460.4160
SOCKET AND WISHBONE SET FOR DAF Ø 75 MM 8
• For mounting and dismounting the bushings on the wishbone of the rear axle pcs
• Suitable for the front and rear bearings with Ø 75mm
• Secure and easy to use
• In conjunction with a workshop press
• Special tool steel
Application range:
DAF wishbone at the rear axle
Dimen- Length Application range
sions mm
e.g. silent bushes for Iveco Eurosta anti-roll
700.1821 58 → 55 85,0 bar /leaf spring € 158,90
e.g. silent bushes for Iveco Eurosta anti-roll
700.1823 63 → 60 85,0 bar /leaf spring € 158,90
700.1825 68 → 63 85,0 e.g. Mercedes anti-roll bar for Actros, Atego € 158,90
700.1827 72 → 68 85,0 e.g. MAN front axle € 158,90
e.g. bearings with pins, Mercedes Actros
700.1829 74 → 70 85,0 € 158,90
645,90 €
Classic
e.g. bearings with pins, Mercedes Actros
700.1831 89 → 84 85,0 anti-roll bar € 174,90
Application:
Ø 51 mm - Volvo FM12 Original *CEJN®
Ø 60 mm - DB / Renault (430/450/460)
Ø 68 mm - MAN-TGA (140/414/460) front axle spring ROR, SAF
Ø 68 mm Ø 60 mm
MAN-TGA Ø 51 mm RENAULT
(410/414/460) VOLVO(FM12) (430/450/460)
1819,90 €
640.0010 640.0020
HYDRAULIC HAND PUMP PNEUMATIC HYDRAULIC PUMP
• Single stage • Pneumatic working
• Reverse valve for advance and return stroke • For simply agent press cylinders
• Safety valve for overload protection • Safety valve for overload protection
• Includes pressure tube 1.8 meters • Includes pressure tube 1.8 meters
• Usable tank volume 2081cm³ = 2.081l • Usable tank volume 2081cm³ = 2.081l
• Operating pressure max. 700 bar
• Output per stroke:
0.8 l/min up to 200 bar
0.1 l/min up to 700 bar
1187,90 € 2037,90 €
Connection thread Length Width H Output per stroke Connection thread Length Width H
mm mm mm cm³ mm mm mm
3/8” - 18 NPT 585 133 119 2,62 3/8” - 18 NPT 255 130 200
640.0030
ELECTRIC HYDRAULIC PUMP
• Two stepped for simply agent press cylinders
• Safety valve for overload protection
• Usable tank volume 1900 cm³ = 1.9l
• Includes pressure tube 1.8 meters
• Motor specification 0.37kW - 220/230 V - 50/60 hertz, single phase (3.2 amps)
1. Step: max. 13 bar
2. Step: max. 700 bar
• Output per stroke:
1. Step: 3.31 l/min
2. Step: 0.32 l/ min
Length Width H
5493,90 €
Connection thread mm mm mm
3/8” - 18 NPT 244 244 362
735,90 €
4-point D1 D2 Number B Height
Receiver For nuts mm mm of studs mm mm
450.5004 1/2 KM4 37,3 28,5 4 4,0 60,0 € 31,90
450.5005 1/2 KM5 44,3 34,5 4 5,0 60,0 € 31,90
440.9997 450.5006 1/2 KM6 52,3 41,5 4 5,0 60,0 € 37,90
UNIVERSAL PRESS TOOL SET FOR AXLE PARTS 38 450.5007 1/2 KM7 59,3 48,5 4 5,0 60,0 € 36,90
• For the assembly and disassembly of bearings, bushes and ball joints pcs
• Adapter and adapter ring allow for use with the universal press stand 450.5008 1/2 KM8 65,5 53,5 4 6,0 60,0 € 36,90
• 22 press sleeves with internal and external diameters between 34.0 mm and 90.0 mm
• Universal usage for passenger cars and transporters 450.5009 3/4 KM9 73,5 60,5 4 6,0 68,0 € 48,90
• Outstanding to use also in connection with workshop press or hydraulic cylinder
• Special tool steel 450.5010 3/4 KM10 78,5 65,5 4 6,0 68,0 € 57,90
Caution: The spindles must be greased before first use! Overloading leads to unwanted material stresses or
450.5011 3/4 KM11 82,5 70,0 4 7,0 68,0 € 50,90
breakage Always check the power settings on the drive with a torque wrench Not to be combined with other
systems
450.5012 3/4 KM12 87,5 74,5 4 7,0 68,0 € 56,90
Maximum allowable torque moments:
Spindle (ACME) M10xP1.5 60 Nm
Spindle (ACME) M12xP2.0 120 Nm 450.5000
Spindle (ACME) M14xP2.0 150 Nm
Spindle (ACME) M16xP2.5 250 Nm SOCKET SET FOR KM GROOVE NUTS, STUDS EXTERIOR 9
• For loosening and tightening groove nuts DIN 981 on crimping or clamping sleeves pcs
• Minimum space on nut size
• Slim design
• Suitable for exact torque possible
• Pin + rubber rings for safe holding
• Working range KM4 to KM12 (nuts of ball bearing)
Application range: Removal and installation of bearings, gear wheels, cone roll bearings, ball bearings etc.
Trucks, land and construction machines, municipally and forestery technology etc.
1249,90 € 327,90 €
*This is an limited special price offer - only until stocks last.
All prices are ex. VAT. With the release of this leaflet all previous prices became invalid. Sold only in specialist stores. Print mistakes, errors and technical alterations excepted. Prices valid up to
31.12.2022
39
AXLES - SPECIAL TOOLS
82,90 €
D1 D2 D3 Number of B H
mm mm mm studs mm mm
72,0 57,0 50,0 4 6,0 55,0
4-point D1 D2 Number B Height
Receiver For nuts mm mm of studs mm mm
450.5024 1/2” KM4 42,0 28,3 4 4,0 60,0 € 31,90 455.0100
SPECIAL SOCKET FOR 8 POINT SCREWS
450.5025 1/2” KM5 50,0 34,3 4 5,0 60,0 € 34,90
• Special 8 point internal profile
450.5026 1/2” KM6 59,0 41,3 4 5,0 60,0 € 36,90 • To the dismantling and assembly of the control switch for the differential lock
• Ideally suited also for various electric switches on the transmissions
450.5027 1/2” KM7 66,0 48,3 4 5,0 60,0 € 42,90 • Mirror polished
• Special tool steel
450.5028 1/2” KM8 73,0 53,5 4 6,0 60,0 € 48,90
Application range: MAN, Mercedes LKW Actros, SK Baureihe etc.
450.5029 3/4” KM9 80,0 60,5 4 6,0 68,0 € 51,90
450.5030 3/4” KM10 86,0 65,5 4 6,0 68,0 € 61,90
450.5031 3/4” KM11 93,0 69,5 4 7,0 68,0 € 61,90
450.5032 3/4” KM12 98,0 74,5 4 7,0 68,0 € 61,90
450.5020
SOCKET SET FOR KM GROOVE NUTS, STUDS INTERNAL 9
• For loosening and tightening groove nuts DIN 981 on crimping or clamping sleeves pcs
36,90 €
• Minimum space on nut size
• Internal studs for high torque
• Use in conjunction with extensions, ratchets etc.
• Suitable for exact torque
• Pin + rubber rings for safe holding Spanner width Ø Length
• Working range KM4 to KM12 (nuts of ball bearing) profile mm mm mm
Application: Removal and installation of bearings, gear wheels, cone roll bearings, ball bearings etc. 8 point 27 34,0 57,0
Trucks, land and construction machines, municipally and forestery technology etc.
460.3815
WRENCH WITH 6 PINS FOR MERCEDES
3/4“: KM9 - KM10 - KM11 - KM12 • Removal and installation of differential nuts
• External drive hexagonal socket 32.0 mm
• High accuracy of fit
• Extremely robust version
• Suitable for high tightening and loosening torque
• Special tool steel
73,90 €
407,90 € D1
mm
84,0
D2
mm
58,0
D3
mm
72,0
Number of
studs
6
B
mm
10,7
Length
mm
60,5
Depth
mm
9,0
Application range: DAF (CF) 35 t Application range: MAN differential roll bearing
30 mm
1079,90 €
460.3685
DIFFERENTIAL MAIN SHAFT BEARINGS PULLER SET FOR DAF 10 Ø 115 / 137 mm
• For damage-free mounting and dismounting of the differential’s main shaft bearings pcs
• Extremely sturdy execution
• Including 2 half-shell pairs
• Trapezoid thread spindle for high removal power - drive 30 mm
979,90 €
• Special tool steel
460.3905
DIFFERENTIAL MAIN SHAFT BEARINGS PULLER SET FOR SCANIA 7
• For damage-free removal of the main shaft bearings of the differential pcs
• Extremely sturdy execution
• Including 2 half-shell pairs
• Trapezoid thread spindle for high removal power - drive 30 mm
• Special tool steel
843,90 €
460.3690
DIFFERENTIAL MAIN SHAFT BEARINGS PULLER SET FOR DAF 14
AND SCANIA pcs
• For damage-free removal of the main shaft bearings of the differential
• Extremely sturdy execution
• Including 4 half-shell pairs
• Trapezoid thread spindle for high removal power - drive 30 mm
• Special tool steel
1589,90 € 917,90 €
*This is an limited special price offer - only until stocks last.
All prices are ex. VAT. With the release of this leaflet all previous prices became invalid. Sold only in specialist stores. Print mistakes, errors and technical alterations excepted. Prices valid up to
31.12.2022
41
AXLES - SPECIAL TOOLS
460.3910 460.1050
DIFFERENTIAL MAIN SHAFT BEARINGS PULLER SET FOR VOLVO 8 LIFTING CYLINDER TOOL SET 2
• For damage-free removal of the main shaft bearings of the differential pcs • for mounting and dismounting the oil seal on the hydraulic lifting cylinder pcs
• Extremely sturdy execution • Internal square drive to DIN 3121 / ISO 1174
• Including 2 half-shell pairs • Extremely sturdy execution
• Trapezoid thread spindle for high removal power - drive 30 mm • For machinery usage
• Special tool steel • Special tool steel
Application range: Volvo (FM12) Application range: Volvo FM12 >2005 Lifting cylinder tandem axle lifter
129,90 €
460.5475
SHAFT SEAL ASSEMBLY MANDREL FOR MERCEDES
• ideally suited for damage-free installation of the shaft sealing rings
• To be used with a rubber hammer
• Seal seats are spared
• Special tool steel
798,90 €
460.4360
DIFFERENTIAL MAIN SHAFT BEARINGS PULLER SET FOR VOLVO 12
• For damage-free removal of the main shaft bearings of the differential pcs
• Extremely sturdy execution
• Including 3 half-shell pairs
• Trapezoid thread spindle for high removal power - drive 30 mm
• Special tool steel
460.5476
SHAFT SEAL ASSEMBLY MANDREL FOR MERCEDES
• ideally suited for damage-free assembly of the cassette shaft seals
• To be used with a rubber hammer
• Seal seats are spared
• Special tool steel
135,90 €
Ø1 Ø2 Ø3 Ø4 Height
1299,
mm mm mm mm mm
90
€ 165,0 152,5 142,0 132,0 158,0
158,90 € 214,90 €
Ø1 Ø2 Height Spanner width Ø Height
mm mm mm mm mm mm
176,0 142,0 164,0 130,0 155,0 77,0
460.5478 460.4790
POLE WHEEL MOUNTING MANDREL FOR MERCEDES AXLE NUT WRENCH FOR SAF
• ideally suited for damage-free installation of the pole wheels • With hexagon drive 32.0 mm
• To be used with a rubber hammer • 6 point
• Seal seats are spared • Very high degree of accuracy
• Special tool steel • Extremely robust version
• Suitable for high tightening and loosening torque
Application range: Mercedes Actros VA with brake discs and ABS, lift axles as well as identical axles of • Special tool steel
supports
Application range: SAF trailer axle
174,90 € 104,90 €
Ø1 Ø2 Height Spanner width 6-point Ø Height
mm mm mm mm mm mm mm
186,0 159,0 162,0 85,0 32 140 102,0
907.2237 450.0201
CARBIDE SCRAPER AXLE NUT WRENCH FOR SAF
• ideal for removing stubborn impurities, sealant residues • Six sided drive 36 mm
and surface treatment • Positive drive of the axle nut
• for burnt on pads on the exhaust, brakes etc. • Any extensive slipping is avoided
• with a very hard-wearing carbide cutting element • Milled out profile
• a solid blade with two scraping edges • Sturdy design
• Extremely long service life • Can be used with an impact wrench or torque wrench
• works as a compression and a pulling blade • Special tool steel
• With an ergonomic, moulded, one component handle
• With reinforcement eyelet Application range: SAF axle trailers
32 mm
197,90 €
210 mm Spanner width 6-point Ø Height
56,
mm mm mm mm
90
€ 85,0 36 118,0 82,0
Application range:
SAF Euro axle etc.
158,90 € 299,90 €
Spanner width 6-point Height Ø1 Ø2 Ø3 Ø4
mm mm mm mm mm mm mm
140,0 32 100,0 185,0 174,0 165,0 158,0
460.4705 460.4815
WHEEL HUB PULLER SET FOR SAF 2 THRUST PIECE FOR WHEEL HUB FOR SAF
• For 140 mm hole diameters pcs • Thrust piece for removing wheel hubs
• Sturdy design • can be used with pullers 440.0590, 440.0610 and 450.1765
• Threaded spindle for high pull-off force - 32 mm drive • Sturdy design
• Special tool steel • Special tool steel
56,90 €
External Ø Internal Ø
129,
mm mm
90
€ 88,0 82,0
460.4845 460.4875
WHEEL BEARING MOUNTING SLEEVE FOR SAF HD BUSHING TOOL SET FOR SAF 9
• ideally suited for mounting and dismounting the compact wheel bearing with wheel hub on SAF axles • ideally suited for disassembly and assembly of the HD bushings on SAF axles pcs
• with right and left-hand thread • Sturdy design
• Sturdy design • Threaded spindle for high pull-off force - 30.0 mm drive
• Special tool steel • Special tool steel
104,90 €
Thread Ø Length
mm mm
M70 x 82,0 150,0
1.5
460.4795
WHEEL BEARING MOUNTING SLEEVE FOR SAF
• ideally suited for mounting and dismounting the compact wheel bearing with wheel hub on SAF axles
• with right and left-hand thread
• Sturdy design
• Special tool steel
146,90 €
Thread Ø Length
1579,90 €
mm mm
M75 x 88,0 150,0
1.5
333,90 €
460.4720
BRAKE CALIPER REPAIR KIT 36
• for the professional repair of callipers pcs
• for the replacement of bellows, calliper bearings and the internal sealing of the bellow
• Secure and easy to use
• High accuracy of fit
• Enormous time and cost saving
• Special tool steel
• In durable plastic storage case
1359,90 €
Haldex Modul T (SAF, SBS2220 H0)
460.4900
ARCING WHEEL MOUNTING TOOL FOR SAF
• ideally suited for mounting pole wheels
on SAF axles
• Sturdy design
• Special tool steel
985,90 €
Application range: SAF axles S-, Z-Series
460.4850
DOUBLE LEVER FOR SNAP RING RIMS
• ideally suited for dismantling snap ring rims
• Special shape
• Special tool steel
339,90 €
460.4670
ASSEMBLY MANDREL FOR BEARING RING AND EXCITER RING FOR SAF 360 mm
• ideally suited for mounting bearing rings and pole wheels on SAF axles
61,90 €
• Sturdy design
• Special tool steel
Application range: SAF axles SK RB 9022 KI(01), SK RB 9019KI, SK RB 9019 WI, SK RB 9022WI, B(I)9-19K,
B(I)9-19W, B(I)9-19K01, B(I)9-22W (6), BA9-22K01
460.4855
OPENING LEVER FOR THREE-PIECE RIMS
• ideally suited for the assembly and disassembly of three-piece rims
• Special shape
• Special tool steel
288,90 € 402 mm
Ø1 Ø2 Ø3 Height
73,90 €
mm mm mm mm
159,0 138,0 80,0 104,0
582,90 €
440.0385
BUSHING SET FOR SAF 6
• for mounting and dismounting the 3D bearing (150mm) on SAF axles pcs
• extremely robust 500mm tie rods with inductively hardened thread
• Enables use directly on the vehicle
• ideal for use with 32t hydraulic cylinder (440.0025)
• Simple handling
• Special tool steel
460.4700
CLAMPING FIXTURE SET FOR DRUM LATHE Ø 50 MM 2
• suitable for use with brake drum lathe pcs
• Sturdy design
• Special tool steel
611,90 €
Ø 205 mm Ø 142 mm
WHEEL CAP IMPACT WRENCH FOR BPW
• For the assembly and dismantling of grease caps on BPW axles
• 8-point
• Extremly versatile
• With impact area
460.4710
3.1/2” LIMIT GAUGE FOR CHECKING THE WEAR LIMIT OF THE KINGPIN
• to check the wear limit of the kingpin
• relevant for the safety check Spanner width mm Length
• Sturdy design mm
460.4685 95 233,0 € 99,90
Application range: kingpin
460.4690 110 240,0 € 104,90
Application range:
BPW axle nuts (crown nuts)
16 tonne axles
85
80,0
300,0
€
€
67,90
73,90
158,90 €
Spanner width D Height T
460.4939 95 85,0 € 82,90 mm mm mm mm
460.4940 100 80,0 € 93,90 85,0 110,0 84,0 33,0
Spanner width mm Ø
mm
Height
mm
104,90 €
Spanner width Ø Height
450.0204 65,0 82,0 66,0 € 93,90 mm mm mm
450.0205 80,0 100,0 80,0 € 136,90 46 64 64,0
186,90 € 124,90 €
Spanner width Ø Height Spanner width 6-point Ø Height
mm mm mm mm mm mm mm
95 115 91,0 95,0 41 110,0 90,0
460.1325 450.0208
HUB CAP SOCKET FOR BPW HUB CAP SOCKET FOR BPW
• Internal square drive to DIN 3121 / ISO 1174 • For the assembly and dismantling of grease caps on BPW axles
• For the assembly and dismantling of grease caps on BPW axles • Extremly versatile
• 8-point • Flat oval form
• Extremly versatile • Suitable for exact torque on a hexagon head possible
• Suitable for exact torque on a hexagon head possible • Suitable for high tightening and loosening torque
• Suitable for high tightening and loosening torque • For machinery usage
• For machinery usage • Special tool steel
• Special tool steel
158,90 € 174,90 €
Spanner width Ø Height Spanner width 6-point Ø Height
mm mm mm mm mm mm mm
110,0 132,0 80,0 111,0 41 132,0 90,0
460.0415 460.0420
HUB CAP SOCKET FOR BPW AXLE NUT WRENCH FOR BPW
• For the assembly and dismantling of grease caps on BPW axles • Internal square drive to DIN 3121 / ISO 1174
• 8-point • Flat oval form
• Extremly versatile • High accuracy of fit
• Suitable for exact torque on a hexagon head possible • Extremely robust version
• Suitable for high tightening and loosening torque • Suitable for high tightening and loosening torque
• For machinery usage • Special tool steel
• Special tool steel
Application range: BPW axles 12 t
146,90 € 175,90 €
Spanner width 6-point Ø Height Spanner width Ø Height
mm mm mm mm mm mm mm
111,0 41 130,0 95,0 111,0 132,0 80,0
Ø
mm
460.4952 100,0 € 82,90
460.4956 113,0 € 93,90
460.4955 123,0 € 99,90
460.4957 123,0 € 99,90
174,90 €
460.4954 142,0 € 124,90
460.4951 157,0 € 124,90
Spanner width Ø Height 460.4953 160,0 € 129,90
mm mm mm
120,0 142,0 95,0
RACEWAY PRESS-IN TOOL FOR BPW
• Raceway installation aid
• For damage free mounting
460.1830 • Extremly versatile
• Special tool steel
WHEEL CAP SOCKET WRENCH FOR BPW
• for mounting and dismounting BPW hubcaps Application range: Hub sealing rings
• Internal square drive to DIN 3121 / ISO 1174
• Flat oval form
• High accuracy of fit
• Extremely robust version
• Suitable for high tightening and loosening torque
• For machinery usage
• Special tool steel Ø Height suitable for
mm mm
Application range: BPW axles ECO / ECO Plus 2 460.4958 139,0 48,0 02.5683.62.00 € 231,90
460.4960 159,0 38,0 02.5683.80.00 € 197,90
460.4959 159,0 48,0 02.5683.63.00 € 271,90
460.4870
TAPER ROLLER BEARING EXTRACTOR FOR BPW
• ideally suited for the removal of fixed tapered roller bearings with thrust ring
• Sturdy design
299,90 €
• Special tool steel
460.4755
POLE WHEEL MOUNTING TOOL FOR BPW
• ideally suited for mounting pole wheels on BPW axles
• Sturdy design
• Special tool steel
158,90 € 141,90 €
460.1010 460.4860
BPW SEAL ASSEMBLY PIN ASSEMBLY TOOL SET FOR BRASS BUSHING LOCATING BEARING 5
• Ideal for the protective assembly of seals • ideally suited for disassembly and assembly of brass bushes Fixed bearing on disc brakes pcs
• Suitable for manual operation • Sturdy design
• To be used with a rubber hammer • Special tool steel
• Special tool steel
Application range: BPW disc brakes
Application range: BPW 12 t trailer
104, 90
€
146,90 €
Ø Length 460.4905
mm
159,0
mm
166,0
PULL-OUT AND PULL-IN TOOL FOR FLOATING BEARINGS 7
AND GUIDE SLEEVES BPW pcs
• for professional brake repair
460.4980 • for pulling out and in of the guide sleeves of the floating bearings
• Secure and easy to use
LEVER FOR BRAKE RETURN SPRING MOUNTING FOR BPW • Very high degree of accuracy
• Enormous time and cost saving
• ideally suited for the disassembly and assembly of brake springs on drum brakes • Special tool steel
• Used for cylindrical and conical retaining clips
• Special tool steel Application range: BPW SH and SKH
300 mm 248,90 €
31,90 € 460.4760
STEEL-RUBBER BUSHES DISMANTLING ASSEMBLY TOOL FOR BPW 6
460.4770 • Assembly and disassembly of bushings pcs
• ideally suited for steel-rubber bushings on shackle stabilisers
PULLING DEVICE FOR BRAKE PINS ON THE DRUM BRAKE • Enables de -and assembly directly on the vehicle
• ideally suited for the dismantling of brake pins on the drum brakes • Easy to use
• incl. threaded insert M 20 x 1.5 mm / M 20 x 1.5 mm • Saves a lot of time
• Sturdy design • Special tool steel
• Special tool steel
320 mm
299,90 € 203,90 €
*This is an limited special price offer - only until stocks last.
50 All prices are ex. VAT. With the release of this leaflet all previous prices became invalid. Sold only in specialist stores. Print mistakes, errors and technical alterations excepted. Prices valid up to
31.12.2022
AXLES - SPECIAL TOOLS
M30 x 1,5 mm
620 mm
271,90 €
460.4996
Ø MEASURING TUBE EXTENSION FOR BPW
mm
• ideally suited for aligning axes and assemblies in conjunction with the screw-in heads 460.4992, 460.4993
460.4990 24,0 € 186,90
and 460.4994
• Sturdy design
460.4991 30,0 € 186,90 • Special tool steel
271,90 €
460.4997
JACKING BOLT FOR BPW
• ideally suited as extraction device for hubs in connection with the screw-in heads 460.4992, 460.4993 and
460.4994
• Sturdy design
• Special tool steel
M30 x 1,5 mm
Receiver
mm
460.4992 M125 x 2 € 333,90
460.4993 M135 x 2 € 378,90
460.4994 M136 x 2,5 € 367,90 124,90 €
150.1810
ALIGNMENT TOOL SET FOR LIGHT AND HEAVY COMMERCIAL VEHICLE 21
• Universal application, independently of hole spacing and number of bolts pcs
• For repair work on steering and suspension components
• Restoring of the original wheel adjustment parameters such as toe-in and track width after a repair
• when replacing suspension parts, e.g.: Track rod end (ball joint)
• Independent of mains power supply and measuring location
• In durable plastic storage case
259,90 €
*This is an limited special price offer - only until stocks last.
All prices are ex. VAT. With the release of this leaflet all previous prices became invalid. Sold only in specialist stores. Print mistakes, errors and technical alterations excepted. Prices valid up to
31.12.2022
51
...AND YOU WANT
MORE?
WWW.KSTOOLS.COM
GERMANY
Tel.: +49(0) 61 04 49 74-0
Fax: +49(0) 61 04 49 74-11
e-mail: kstools@kstools.de
www.kstools.com