DS Series: DS-101AC DS-102AC DS-103AC DS-105AC

SURVEYING INSTRUMENTS
INSTRUCTION MANUAL
Direct aiming Station
DS series
DS-101AC
DS-102AC
DS-103AC
DS-105AC
21309 90041
HOW TO READ THIS MANUAL
Thank you for selecting the DS-101AC/102AC/103AC/105AC.
• Please read this Operator’s manual carefully, before using this product.
• DS has a function to output data to a connected host computer. Command operations from a host
computer can also be performed. For details, refer to "Communication manual" and ask your local
dealer.
• The specifications and general appearance of the instrument are subject to change without prior
notice and without obligation by TOPCON CORPORATION and may differ from those appearing in
this manual.
• The content of this manual is subject to change without notice.
• Some of the diagrams shown in this manual may be simplified for easier understanding.
• This manual is protected by copyright and all rights are reserved by TOPCON CORPORATION.
• Except as permitted by Copyright law, this manual may not be copied, and no part of this manual
may be reproduced in any form or by any means.
• This manual may not be modified, adapted or otherwise used for the production of derivative works.
Symbols
The following conventions are used in this manual.
G : Indicates precautions and important items which should be read before

operations.
C : Indicates the chapter title to refer to for additional information.
$ : Indicates supplementary explanation.
& : Indicates an explanation for a particular term or operation.
[Softkey] etc. : Indicates softkeys on the display and window dialog buttons.
{Key} etc. : Indicates keys on the operation panel.
<Screen title> etc. : Indicates screen titles.
i
Notes regarding manual style
• Except where stated, “DS” means DS-101AC/102AC/103AC/105AC in this manual.

• Face 2 display is available as standard or as a factory option depending on the country of purchase.
• Location of softkeys in screens used in procedures is based on the factory setting. It is possible to
change the allocation of softkeys.
CSoftkey allocation: "19.6 Allocating Key Functions"
• Learn basic operations in "4. PRODUCT OUTLINE" and "5. BASIC OPERATION" before you read
each measurement procedure. For selecting options and inputting figures, see "5.1 Basic Key
Operation".
• Measurement procedures are based on continuous measurement. Some information about
procedures when other measurement options are selected can be found in “Note” ($).
• KODAK is a registered trademark of Eastman Kodak Company.

• Bluetooth® is a registered trademark of Bluetooth SIG, Inc.
• Windows and Windows CE are registered trademarks of Microsoft Corporation.
• All other company and product names featured in this manual are trademarks or registered
trademarks of each respective organization.
S Li-ion
Li-ion
This is the mark of the Japan Surveying

Instruments Manufacturers Association.
ii
CONTENTS
1. PRECAUTIONS FOR SAFE OPERATION............................ 1
2. PRECAUTIONS ..................................................................... 4
3. LASER SAFETY INFORMATION .......................................... 7
4. PRODUCT OUTLINE............................................................. 9
4.1 Parts of the Instrument .................................................................... 9
4.2 Mode Structure .............................................................................. 14
4.3 Bluetooth Wireless Technology ..................................................... 15
5. BASIC OPERATION ............................................................ 17
5.1 Basic Key Operation ...................................................................... 17
5.2 Display Functions .......................................................................... 21
5.3 Inputting Characters using the Input Panel ................................... 25
5.4 Starkey Mode ................................................................................ 26
5.5 Using the Program Selection Screen ............................................ 31
6. USING THE BATTERY........................................................ 32
6.1 Battery Charging ........................................................................... 32
6.2 Installing/Removing the Battery ..................................................... 33
7. SETTING UP THE INSTRUMENT....................................... 35
7.1 Centering ....................................................................................... 35
7.2 Levelling ........................................................................................ 37
8. POWER ON/OFF................................................................. 39
8.1 Resolving Software Issues ............................................................ 40
8.2 Configuring the Touch Panel ......................................................... 40
8.3 Powering ON/OFF from an External Instrument ........................... 41
9. CONNECTING TO EXTERNAL DEVICES .......................... 42
9.1 Wireless Communication using Bluetooth Technology ................. 42
9.2 Communication between the DS and Companion Device ............ 46
9.3 Connection via RS232C Cable ...................................................... 47
9.4 Connecting via USB Cable ............................................................ 48
9.5 Inserting USB Memory .................................................................. 51
10. TARGET SIGHTING ............................................................ 52
10.1 Auto Pointing Settings ................................................................... 53
10.2 Auto-Pointing Function for Target Sighting ................................... 55
10.3 Manually Sighting the Target ......................................................... 56
11. ANGLE MEASUREMENT.................................................... 58
11.1 Measuring the Horizontal Angle between Two Points
iii
CONTENTS
(Horizontal Angle 0°) ..................................................................... 58
11.2 Setting the Horizontal Angle to a Required Value
(Horizontal Angle Hold) ................................................................. 59
11.3 Turning the Instrument from the Reference Angle to
a Specified Angle .......................................................................... 60
11.4 Angle measurement and Outputting the Data ............................... 61
12. DISTANCE MEASUREMENT.............................................. 62
12.1 Returned Signal Checking ............................................................. 62
12.2 Using the Guide Light in Distance Measurement .......................... 64
12.3 Distance and Angle Measurement ................................................ 65
12.4 Distance Measurement and Outputting the Data .......................... 66
12.5 REM Measurement ....................................................................... 67
13. COORDINATE MEASUREMENT ........................................ 69
13.1 Entering Instrument Station Data .................................................. 69
13.2 Azimuth Angle Setting ................................................................... 70
13.3 3-D Coordinate Measurement ....................................................... 73
14. RESECTION MEASUREMENT ........................................... 75
14.1 Coordinate Resection Measurement ............................................. 76
14.2 Height Resection Measurement .................................................... 80
15. SETTING-OUT MEASUREMENT........................................ 85
15.1 Using the Guide Light in Setting-out Measurement ....................... 85
15.2 Distance Setting-out Measurement ............................................... 86
15.3 Coordinates Setting-out Measurement .......................................... 90
15.4 REM Setting-out Measurement ..................................................... 94
16. OFFSET MEASUREMENT.................................................. 96
16.1 Offset Single-distance Measurement ............................................ 96
16.2 Offset Angle Measurement ............................................................ 98
16.3 Offset Two-distance Measurement ............................................. 100
17. MISSING LINE MEASUREMENT...................................... 103
17.1 Measuring the Distance between 2 or more Points ..................... 103
17.2 Changing the Starting Point ........................................................ 105
18. SURFACE AREA CALCULATION..................................... 107
19. CHANGING THE SETTINGS ............................................ 111
19.1 Observation Conditions ............................................................... 111
19.2 Instrument Configuration ............................................................. 114
19.3 EDM Settings .............................................................................. 116
iv
CONTENTS
19.4 Allocating User-defined Tabs ...................................................... 120
19.5 Customizing Screen Controls ...................................................... 123
19.6 Allocating Key Functions ............................................................. 125
19.7 Changing Starkey Mode Icons .................................................... 128
19.8 Units ............................................................................................ 130
19.9 Changing Password .................................................................... 131
19.10 Restoring Default Settings ........................................................... 132
19.11 Date and Time ............................................................................. 132
20. WARNING AND ERROR MESSAGES.............................. 133
21. CHECKS AND ADJUSTMENTS........................................ 136
21.1 Circular Level .............................................................................. 136
21.2 Tilt Sensor ................................................................................... 137
21.3 Collimation ................................................................................... 140
21.4 Reticle ......................................................................................... 141
21.5 Image Sensor Reticle .................................................................. 143
21.6 Optical Plummet .......................................................................... 145
21.7 Additive Distance Constant ......................................................... 146
21.8 Laser Plummet (Option) .............................................................. 147
22. POWER SUPPLY SYSTEM .............................................. 150
23. PRISM SYSTEM................................................................ 151
24. OPPTIONAL ACCESSORIES ........................................... 152
25. SPECIFICATIONS ............................................................. 154
26. EXPLANATIONS .............................................................. 161
26.1 High Accuracy with the 360° Prism ............................................. 161
26.2 Manually Indexing the Vertical Circle by Face Left,
Face Right Measurement ............................................................ 162
27. REGULATIONS ................................................................. 163
28. INDEX ................................................................................ 167
v
1. PRECAUTIONS FOR SAFE OPERATION
For the safe use of the product and prevention of injury to operators and other persons as well as
prevention of property damage, items which should be observed are indicated by an exclamation point
within a triangle used with WARNING and CAUTION statements in this operator’s manual.
The definitions of the indications are listed below. Be sure you understand them before reading the
manual’s main text.
Definition of Indication
Ignoring this indication and making an operation error could possibly

C WARNING
result in death or serious injury to the operator.
Ignoring this indication and making an operation error could possibly

C CAUTION
result in personal injury or property damage.
This symbol indicates items for which caution (hazard warnings inclusive) is urged.
J Specific details are printed in or near the symbol.
This symbol indicates items which are prohibited. Specific details are printed in or near
D the symbol.
This symbol indicates items which must always be performed. Specific details are printed
I in or near the symbol.
General
C Warning
Do not use the unit in areas exposed to high amounts of dust or ash, in areas where there
D is inadequate ventilation, or near combustible materials. An explosion could occur.
Do not perform disassembly or rebuilding. Fire, electric shock, burns, or hazardous

G radiation exposure could result.
D Never look at the sun through the telescope. Loss of eyesight could result.
Do not look at reflected sunlight from a prism or other reflecting object through the
D telescope. Loss of eyesight could result.
Direct viewing of the sun using the telescope during sun observation will cause loss of
E eyesight. Use a solar filter (option) for sun observation.
When securing the instrument in the carrying case make sure that all catches, including
E the side catches, are closed. Failure to do so could result in the instrument falling out
while being carried, causing injury.
C Caution
Do not use the carrying case as a footstool. The case is slippery and unstable so a
D person could slip and fall off it.
1
Do not place the instrument in a case with a damaged catch, belt or handle. The case or
D instrument could be dropped and cause injury.
Do not touch the instrument or look through the telescope while the motor is in operation.
D Injury could result.
D Do not wield or throw the plumb bob. A person could be injured if struck.
Secure handle to main unit with handle locks. Failure to properly secure the handle could
E result in the unit falling off while being carried, causing injury.
Tighten the adjustment tribrach clamp securely. Failure to properly secure the clamp
E could result in the tribrach falling off while being carried, causing injury.
Power Supply
C Warning
D Do not short circuit. Heat or ignition could result.
Do not place articles such as clothing on the battery charger while charging batteries.
D Sparks could be induced, leading to fire.
Do not use voltage other than the specified power supply voltage. Fire or electrical shock
D could result.
Do not use batteries other than those designated. An explosion could occur, or abnormal
D heat generated, leading to fire.
Do not use damaged power cords, plugs or loose outlets. Fire or electric shock could
D result.
D Do not use power cords other than those designated. Fire could result.
Use only the specified battery charger to recharge batteries. Other chargers may be of
E different voltage rating or polarity, causing sparking which could lead to fire or burns.
Do not use the battery or charger for any other equipment or purpose. Fire or burns
D caused by ignition could result.
Do not heat or throw batteries or chargers into fire. An explosion could occur, resulting in
H injury.
To prevent shorting of the battery in storage, apply insulating tape or equivalent to the
E terminals. Otherwise shorting could occur resulting in fire or burns.
Do not use batteries or the battery charger if wet. Resultant shorting could lead to fire or
D burns.
Do not connect or disconnect power supply plugs with wet hands. Electric shock could
D result.
2
C Caution
Do not touch liquid leaking from batteries. Harmful chemicals could cause burns or
F blisters.
Tripod
C Caution
When mounting the instrument to the tripod, tighten the centering screw securely. Failure
E to tighten the screw properly could result in the instrument falling off the tripod, causing
injury.
Tighten securely the leg fixing screws of the tripod on which the instrument is mounted.
E Failure to tighten the screws could result in the tripod collapsing, causing injury.
Do not carry the tripod with the tripod shoes pointed at other persons. A person could be
D injured if struck by the tripod shoes.
Keep hands and feet away from the tripod shoes when fixing the tripod in the ground. A
E hand or foot stab wound could result.
Tighten the leg fixing screws securely before carrying the tripod. Failure to tighten the
E screws could lead to the tripod legs extending, causing injury.
Bluetooth wireless technology
C Warning
Do not use within the vicinity of hospitals. Malfunction of medical equipment could
D result.
Use the instrument at a distance of at least 22 cm from anyone with a cardiac

E pacemaker. Otherwise, the pacemaker may be adversely affected by the
electromagnetic waves produced and cease to operate as normal.
D Do not use onboard aircraft. The aircraft instrumentation may malfunction as a result.
Do not use within the vicinity of automatic doors, fire alarms and other devices with
D automatic controls as the electromagnetic waves produced may adversely affect
operation resulting in an accident.
3
2. PRECAUTIONS
Telescope
• Aiming the telescope at the sun will cause internal damage to the instrument. Use the solar filter
when observing the sun.
C"24. OPPTIONAL ACCESSORIES"
Tribrach Clamp and Handle
• When the instrument is shipped, the tribrach clamp is held

firmly in place with a locking screw to prevent the
instrument from shifting on the levelling base. Before using
the instrument the first time, loosen this screw with a
screwdriver. And before transporting it, tighten the locking
screw to fasten the tribrach clamp in place so that it will not
shift on the tribrach.
• The handle of the instrument can be removed. When
operating the instrument with the handle attached, always
make sure that the handle is securely fixed to the
instrument body with the handle locks.
Precautions concerning water and dust resistance
The instrument conforms to IP65 specifications for waterproofing and dust resistance when battery
cover, connector cap and the external interface hatch and are closed.
• Be sure to correctly attach the connector caps to protect the instrument from moisture and dust
particles when the connector is not in use.
• Make sure that moisture or dust particles do not come in contact with the terminal or connectors.
Operating the instrument with moisture or dust on the terminal or connectors may cause damage to
the instrument.
• Make sure that the inside of the carrying case and the instrument are dry before closing the case. If
moisture is trapped inside the case, it may cause the instrument to rust.
• If there is a crack or deformation in the rubber packing for the battery cover or external interface
hatch, stop using and replace the packing.
• To retain the waterproof property, it is recommended that you replace the rubber packing once every
two years. To replace the packing, contact your local sales representative.
• Do not press the speaker / luminance sensor / microphone hole using
something with a pointed tip. Doing so will damage an internal waterproof
sheet, resulting in a degraded waterproof property.
Speaker
The Lithium Battery
• The lithium battery is used to maintain the Calendar & Clock function. It can back up data for
approximately 5 years of normal use and storage (Temperature = 20°, humidity = about 50%), but
its lifetime may be shorter depending on circumstances.
4
2. PRECAUTIONS
The Levelling Base
• Always use the levelling base provided. During a traverse observation, it is recommended to use the
same type of levelling base for the target as well for accurate observations.
Backing up data
• Data should be backed up (transferred to an external device etc.) on a regular basis to prevent data
loss.
Other precautions
• Never place the instrument directly on the ground. Sand or dust may cause damage to the screw
holes or the centering screw on the base plate.
• Do not perform vertical rotation of the telescope when using the lens hood, diagonal eyepiece, or
solar filter. Such accessories may strike the instrument causing damage.
• Protect the instrument from heavy shocks or vibration.
• Protect the instrument from rain or drizzle with an umbrella or waterproof cover.
• Never carry the instrument on the tripod to another site.
• Turn the power off before removing the battery.
• Remove the battery before placing the instrument in its case.
• Make sure that the instrument and the protective lining of the carrying case are dry before closing the
case. The case is hermetically sealed and if moisture is trapped inside, the instrument could rust.
• Consult your local dealer before using the instrument under special conditions such as long periods
of continuous use or high levels of humidity. In general, special conditions are treated as being
outside the scope of the product warranty.
Maintenance
• Wipe off moisture completely if the instrument gets wet during survey work.
• Always clean the instrument before returning it to the case. The lens requires special care. First,
dust it off with the lens brush to remove tiny particles. Then, after providing a little condensation by
breathing on the lens, wipe it with the wiping cloth.
• If the display is dirty, carefully wipe it with a soft, dry cloth. To clean other parts of the instrument or
the carrying case, lightly moisten a soft cloth in a mild detergent solution. Wring out excess water
until the cloth is slightly damp, then carefully wipe the surface of the unit. Do not use any alkaline
cleaning solutions, alcohol, or any other organic solvents on the instrument or display.
CFor temporal de-activating the touch panel, see "5.2 Display Functions", "19. CHANGING THE
SETTINGS"
• Store the instrument in a dry room where the temperature remains fairly constant.
• Check the tripod for loose fit and loose screws.
• If any trouble is found on the rotatable portion, screws or optical parts (e.g. lens), contact your local
dealer.
• When the instrument is not used for a long time, check it at least once every 3 months.
C"21. CHECKS AND ADJUSTMENTS"
• Every 4,000 to 5,000 hours operation in total, change grease of driving parts. Contact your local
dealer for the maintenance.
• When removing the instrument from the carrying case, never pull it out by force. The empty carrying
case should be closed to protect it from moisture.
5
2. PRECAUTIONS
• Check the instrument for proper adjustment periodically to maintain the instrument accuracy.
Exporting this product
• This product is equipped with the parts/units, and contains software/technology, which are subject
to the EAR (Export Administration Regulations). Depending on countries you wish to export or bring
the product to, a US export license may be required. In such a case, it is your responsibility to obtain
the license. The countries requiring the license as of January 2012 are shown below. Please consult
the Export Administration Regulations as they are subject to change.
North Korea
Iran
Syria
Sudan
Cuba
URL for the EAR of the US: http://www.access.gpo.gov/bis/ear/ear_data.html
Exceptions from responsibility
• The user of this product is expected to follow all operating instructions and make periodic checks
(hardware only) of the product’s performance.
• The manufacturer, or its representatives, assumes no responsibility for results of faulty or intentional
usage or misuse including any direct, indirect, consequential damage, or loss of profits.
• The manufacturer, or its representatives, assumes no responsibility for consequential damage, or
loss of profits due to any natural disaster, (earthquake, storms, floods etc.), fire, accident, or an act
of a third party and/or usage under unusual conditions.
• The manufacturer, or its representatives, assumes no responsibility for any damage (change of
data, loss of data, loss of profits, an interruption of business etc.) caused by use of the product or
an unusable product.
• The manufacturer, or its representatives, assumes no responsibility for any damage, and loss of
profits caused by usage different to that explained in the operator’s manual.
• The manufacturer, or its representatives, assumes no responsibility for damage caused by incorrect
operation, or action resulting from connecting to other products.
6
3. LASER SAFETY INFORMATION
The instrument is classified as the following class of Laser Product according to IEC Standard
Publication 60825-1 Ed.2.0: 2007 and United States Government Code of Federal Regulation FDA
CDRH 21CFR Part 1040.10 and 1040.11 (Complies with FDA performance standards for laser
products except for deviations pursuant to Laser Notice No.50, dated June 24, 2007.)
• EDM device in objective lens: Class 3R Laser Product

(When using prism or reflective sheet as target)Class 1 Laser Product
• Laser plummet (option): Class 2 Laser product
࡟࡯ࠩశߩ಴ญ
AVOID EXPOSURE-Laser radiation
is emitted from this aperture.
Laser beam emitted

from here
* ࡟࡯ࠩశ
⋡߳ߩ⋥ធⵍ߫ߊࠍㆱߌࠆߎߣ
/#:O9.&PO
ࠢ࡜ࠬ4࡟࡯ࠩ⵾ຠ
,+5%
LASER RADIATION
AVOID DIRECT EYE EXPOSURE
MAX 5mW LD 625-695nm
CLASS3R LASER PRODUCT
* Laser beam emitted from here IEC 60825-1 Ed. 2.0 : 2007
(only when laser plummet

function is mounted)
G
• EDM device is classified as Class 3R Laser Product when reflectorless measurement is selected.
When the prism or reflective sheet is selected as target, the output is equivalent to the safer class 1.
CWarning
• Use of controls or adjustments or performance of procedures other than those specified herein may
result in hazardous radiation exposure.
• Follow the safety instructions on the labels attached to the instrument as well as in this manual to
ensure safe use of this laser product.
• Never point the laser beam at another person. If the laser beam strikes skin or an eye, it could cause
serious injury.
• Do not look directly into the laser beam source or guide light source. Doing so could cause
permanent eye damage.
• Do not stare at the laser beam. Doing so could cause permanent eye damage.
• If an eye injury is caused by exposure to the laser beam, seek immediate medical attention from a
licensed ophthalmologist.
• Never look at the laser beam through a telescope, binoculars or other optical instruments. Doing so
could cause permanent eye damage.
• Sight the target so that the laser beam does not stray from them.
7
3. LASER SAFETY INFORMATION
CCaution
• Perform checks at start of work and periodic checks and adjustments with the laser beam emitted
under normal conditions.
• When the instrument is not being used, turn off the power and replace the lens cap.
• When disposing of the instrument, destroy the battery connector so that the laser beam cannot be
emitted.
• Operate the instrument with due caution to avoid injuries that may be caused by the laser beam
unintentionally striking a person in the eye. Avoid setting the instrument at heights at which the path
of the laser beam may strike pedestrians or drivers at head height.
• Never point the laser beam at mirrors, windows or surfaces that are highly reflective. The reflected
laser beam could cause serious injury.
• Only those who have been received training as per the following items shall use this product.
• Read this manual for usage procedures for this product.
• Hazardous protection procedures (read this chapter).
• Requisite protective gear (read this chapter).
• Accident reporting procedures (stipulate procedures beforehand for transporting the injured and
contacting physicians in case there are laser induced injuries).
• Persons working within the range of the laser beam are advised to wear eye protection which
corresponds to the laser wavelength of the instrument being used
• Areas in which the lasers are used should be posted with laser warning notices.
• When using the laser-pointer function, be sure to turn OFF the output laser after distance
measurement is completed. Even if distance measurement is canceled, the laser-pointer function is
still operating and the laser beam continues to be emitted.
8
4. PRODUCT OUTLINE
4.1 Parts of the Instrument
Parts and functions of the instrument
Handle
1
2 Bluetooth antenna
18 3 External interface hatch
2
(USB port/reset button)
17 4 & Instrument height mark
3
4 5 Battery cover
6 Display unit
16 7 Circular level
4 8 Serial / External power source connector
15 9 Circular level adjusting screws
5 10 Base plate
14 6 11 Levelling foot screw
12 Levelling base locking screw
13 13 Optical plummet focussing ring
7 14 Optical plummet eyepiece
12 8 15 Optical plummet reticle cover
11 16 Luminance sensor
9
17 Objective lens
10
(Includes "& Laser-pointer function")
18& Guide light
19 Tubular compass slot

32 19 20 Handle locking screw
21 & Vertical Jog
31
20 22 Keyboard
30
C"5.1 Basic Key Operation"
29 23 & Trigger key
4
28 24 & Horizontal Jog
25 Stylus (pen)
4 21 26 Tribrach clamp
27 27 Telescope eyepiece
22 28 Telescope eyepiece screw
29 Telescope knob
23 30 Telescope focussing ring
31&Sighting collimator
16 24 32Instrument center mark
25
26
9
4. PRODUCT OUTLINE
& Instrument height mark

The height of the instrument is as follows:
• 196mm (from levelling base mounting surface to this mark)
"Instrument height" is input when setting instrument station data and is the height from the
surveying point (where the instrument is mounted) to this mark.
& Laser-pointer function

A target can be sighted with a red laser beam in dark locations without the use of the telescope.
& Guide light

Setting-out measurement etc. can be carried out effectively using the guide light. The guide light
is composed of a light that is divided into green and red sections. A poleman can ascertain the
present position by checking the guide light color.
Guide light
green red
(When seen from the objective lens side

while the instrument is in the Face 1 state)
I Guide light status

Light status Meaning
Slow flashing (Red and green Waiting
simultaneously)
Fast flashing (Red and green Searching in progress
simultaneously) Measuring (continuous measurement)
Returned signal checking in progress
Green and red alternate Distance measurement error (no signal, sighting error)
flashing Search error (error screen only)
C"12.2 Using the Guide Light in Distance Measurement", "15.1 Using the Guide Light in
Setting-out Measurement"
10
4. PRODUCT OUTLINE
& Vertical and Horizontal Jogs

The instrument and telescope can be rotated manually by hand or, for more precise adjustments,
by turning the vertical and horizontal Jogs.
The faster the Jogs are turned, the faster the instrument and telescope rotate.
C"10.1 Auto Pointing Settings" step 3
& Trigger key

When the Trigger key is pressed the instrument carries out the operation indicated by the softkey
in bold type on the screen. This allows the user to continue operation without having to return to
the display to press softkeys.
& Sighting collimator

Use sighting collimator to aim the instrument in the direction of the measurement point.
Turn the instrument until the apex of the triangle in the sighting collimator is aligned with the
target. A circle surrounds the triangle to make it easier to locate.
Bluetooth antenna
The Bluetooth antenna allows communication via

Bluetooth wireless technology.
G
• Handle the antenna with care. The antenna may be
damaged if struck during operation or while being
stored in the carrying case.
11
4. PRODUCT OUTLINE
Detaching/attaching the Handle
The carrying handle can be removed from the instrument. To remove it, loosen the handle rocking
screws.
G
• To remove the handle, hold both sides of the handle and lift it straight above. If you hold the handle
by one hand or incline it, the terminal attached on the handle may be damaged.
• Detach the handle if the prism is located at the zenith.
To attache the handle, position the handl as shown, tighthen the 2 handle rocking screws.
Handle
locking screw
Detaching the instrument from the levelling base
1. Loosen the levelling base locking screw by

turning 2 or 3 rotations in the counterclockwise
direction.
2. Turn the tribrach clamp counterclockwise to

loosen.
3. Lift the instrument to detach.
12
4. PRODUCT OUTLINE
Attaching the instrument to the levelling base
1. Check that the levelling base locking screw

has been loosened.
2. Align (1) and (2) and lower the instrument onto

the levelling base.
(1)
3. Turn the tribrach clamp (3) clockwise to
tighten.
4. Turn the levelling base locking screw

clockwise to tighten.
$ (2)
• Always fully tighten the levelling base locking
screw to reduce adverse effects of motor (3)
operation on accuracy and ensure optimal
results.
13
4. PRODUCT OUTLINE
4.2 Mode Structure
The diagram below describes the different modes of the instrument and key operations for navigating
between them.
●Basic mode
Observation mode (switching by tab)
Top menu
C“5.2 Display
Menu mode Functions
”Graphic“ tab”
ÛVersionÝ
=OK?
]ESC_
]‫_ڎ‬
C“13. to 18.”
Config mode
C“19.Changing the settings”
]PRG_ ●Starkey mode

●Program mode C“5.4 Starkey mode”
]‫_ڎ‬
G
• Switching between modes is not possible during distance measurement.
• Do not switch between modes by {PRG} or not turn OFF the power just after pressing {PRG} (during
displaying the message "Executing program mode").
14
4. PRODUCT OUTLINE
4.3 Bluetooth Wireless Technology
G
• Bluetooth communication is only possible with instruments incorporating the Bluetooth module.
• Use of this technology must be authorized according to telecommunications regulations of the
country where the instrument is being used. Contact your local dealer in advance.
C"27. REGULATIONS"
• TOPCON CORPORATION is not liable for the content of any transmission nor any content related
thereto. When communicating important data, run tests beforehand to ascertain that communication
is operating normally.
• Do not divulge the content of any transmission to any third party.
Radio interference when using Bluetooth technology
Bluetooth communication with the DS uses the 2.4 GHz frequency band. This is the same band used
by the devices described below.
•Industrial, scientific, and medical (ISM) equipment such as microwaves and pacemakers.
• portable premises radio equipment (license required) used in factory production lines etc.
• portable specified low-power radio equipment (license-exempt)
•IEEE802.11b/IEEE802.11g standard wireless LAN devices
The above devices use the same frequency band as Bluetooth communications. As a result, using the
DS within proximity to the above devices may result in interference causing communication failure or
reduction of transmission speed.
Although a radio station license is not required for this instrument, bear in mind the following points
when using Bluetooth technology for communication.
I Regarding portable premises radio equipment and portable specified low-power radio
equipment:
• Before starting transmission, check that operation will not take place within the vicinity of
portable premises radio equipment or specified low-power radio equipment.
• In the case that the instrument causes radio interference with portable premises radio
equipment, terminate the connection immediately and take measures to prevent further
interference (e.g. connect using an interface cable).
• In the case that the instrument causes radio interference with portable specified low-power radio
equipment, contact your local dealer.
I When using the DS in proximity to IEEE802.11b or IEEE802.11g standard wireless LAN

devices, turn off all devices not being used.
• Interference may result, causing transmission speed to slow or even disrupting the connection
completely. Turn off all devices not being used.
I Do not use the DS in proximity to microwaves.

• Microwave ovens can cause significant interference resulting in communication failure. Perform
communication at a distance of 3m or more from microwave ovens.
I Refrain from using the DS in proximity to televisions and radios.
15
4. PRODUCT OUTLINE
• Televisions and radios use a different frequency band to Bluetooth communications.

However, even if the DS is used within proximity to the above equipment with no adverse effects
with regard to Bluetooth communication, moving a Bluetooth compatible device (including the
DS) closer to said equipment may result in electronic noise in sound or images, adversely
affecting the performance of televisions and radios.
Precautions regarding transmission
I For best results

• The usable range becomes shorter when obstacles block the line of sight, or devices such as
PDAs or computers are used. Wood, glass and plastic will not impede communication but the
usable range becomes shorter. Moreover, wood, glass and plastic containing metal frames,
plates, foil and other heat shielding elements as well as coatings containing metallic powders
may adversely affect Bluetooth communication and concrete, reinforced concrete, and metal will
render it impossible.
• Use a vinyl or plastic cover to protect the instrument from rain and moisture. Metallic materials
should not be used.
• The direction of the Bluetooth antenna can have adverse effects upon usable range.
I Reduced range due to atmospheric conditions

• The radio waves used by the DS may be absorbed or scattered by rain, fog, and moisture from
the human body with the limit of usable range becoming lower as a result. Similarly, usable range
may also shorten when performing communication in wooded areas. Moreover, as wireless
devices lose signal strength when close to the ground, perform communication at as high a
position as possible.
16
5. BASIC OPERATION
Learn basic key operations here before you read each measurement procedure.
5.1 Basic Key Operation
{ } { }
Display unit { } { }
{ } { } Illumination key
{ }
{ } { }
{ } { }
{ } { }{ }
{ } Target type
{ } Program mode
{ } Input mode
SHIFT {SHIFT }
{ FUNC } Function key { }

Luminance sensor / Microphone
I Power ON/OFF
{ } Power ON
{ } (Press and hold: About 1 Power OFF
second)
I Lighting up the reticle/keys and selecting screen backlight brightness

Switches the reticle illumination and key light On/Off (When Key
{ } light is On, backlight brigthtness goes down)
C Brightness level: "19.2 Instrument Configuration"
I Switching to Starkey mode
{★} Switches to Starkey mode / previous screen
C "5.4 Starkey Mode"
17
5. BASIC OPERATION
I Switching to Program mode

{PRG} Switches to program mode / basic mode
G
• Do not switch between modes by {PRG} or not turn OFF the power just after pressing {PRG}
(during displaying the message "Executing program mode").
I Switching target type

Switches between target types
{ } Prism/360° Prism/Sheet/N-prism (reflectorless)
C"19.3 EDM Settings"

$
• Changes can also be made by tapping the icon on status bar or in Starkey mode.
C"5.2 Display Functions", "5.4 Starkey Mode"
I Switching the Laser-pointer/Guide light ON/OFF
{ } (Press and hold until Turn ON/OFF the laser-pointer/guide light

a beep sounds)
$
• Changes can also be made by tapping the icon on status bar or in Starkey mode.
C"5.2 Display Functions", "5.4 Starkey Mode"
I Switching the page

{FUNC} Toggle between Observation mode screen pages
I Inputting letters/figures
{α} Switch between numerals and alphabetic characters

In alphabetic characters mode, switch between lowercase
{SHIFT} + {1} to {9}
characters and upper case characters each time
In alphabetic characters mode, switch between lowercase
{SHIFT} (Press and hold)
characters and upper case characters
{SHIFT} + {α} Display/hide <Input Panel>
Input numeral or symbol printed above the key (during numeric
input mode)
{0} to {9}
Input alphabetic character in the order they are listed (in
alphabetic input mode)
Input a decimal point (during numeric input mode)
{.}
Input code (in alphabetic input mode)
Input a plus or minus sign (during numeric input mode)
{± }
Input code (in alphabetic input mode)
18
5. BASIC OPERATION
{ESC} Cancel the input data

{TAB} Shift to the next item
{B.S.} Delete a character on the left.
Input a blank space (increments by 1 when setting the date and
{S.P.}
time)
{K}/{L} Move the cursor left/right
{O}/{G} Move the cursor up/down
{ENT} Select/accept input word/value
CInputting rule and inputting special characters: "5.3 Inputting Characters using the Input
Panel"
I Selecting options
{O}/{G} Move the cursor/selection item up/down
{K}/{L} Move the cursor/selection item left/right or select other option
{TAB} Shift to the next item
{S.P.} Display other options
{ENT} Select/accept the option
I Selecting tabs
{O}/{G} Move tab/cursor in tab up/down
{K}/{L} Display next tab at left/right
CTabs: "5.2 Display Functions"
I Others
{ESC} Return to previous screen
Example: Entering "computer" (lower case) as the name of a new device
1. Tap the input mode icon in the status bar (second

from bottom) until "_a" is displayed.
19
5. BASIC OPERATION
2. Press {7} three times.

"c" is displayed.
P1
3. Press {5} three times.

"o" is displayed.
4. Press {L}.
Press {5}. "m" is displayed.
5. Continue to input letters. Press {ENT} to

complete inputting.
20
5. BASIC OPERATION
5.2 Display Functions
Screens can be selected/operated using the keys on the keyboard or the touch panel. The touch panel
can be operated using either the stylus pen provided or your fingers.
It is also possible to de-activate the touch panel temporarily.
C "19. CHANGING THE SETTINGS"
G
• Do not scratch the display or use any sharp implement other than the stylus pen to operate the touch
panel.
Using the stylus
The stylus pen can be used to select menus and buttons on the screen and operate the scroll bar.
Temporarily de-activating the touch panel
The touch panel can be temporarily de-activated. This is especially useful when cleaning the display.
To de-activate, tap on the status bar. <Touch panel temporarily de-activated> is displayed.
The touch panel cannot be operated while the above message is displayed. Press {ESC} to cancel
the message and re-activate the touch panel.
Displaying and operating screens
• To close a screen, tap the cross in the top right corner, or press {ESC}.
• Tabs, softkey allocations, displayed tab items, and character sizes can all be changed in accordance
with user preferences.
C"19. CHANGING THE SETTINGS"
21
5. BASIC OPERATION
Top menu
Instrument name
Serial Number
Application software version
Observation mode screen
(1) Distance
(2) Vertical angle
(3) Horizontal angle
Soft key
(1) Distance
Horizontal distance and height difference are also displayed in "SHVdist" tab.
Displayed items in "SHV" tab can be changed.
C"19.1 Observation Conditions"
(2) Vertical angle

The Vertical angle display can be switched between Zenith (Z=0°)/Horiz (H=0°)/Horiz (H=±90°)
To switch vertical angle/slope in %, press [ZA/%] when allocated to the Observation mode screen.
The capitalized letter in the softkey indicates the currently selected mode.
CChanging display: "19.1 Observation Conditions", allocating [ZA/%]: "19.6 Allocating Key
Functions"
(3)Horizontal angle
Press [R/L] when allocated to the Observation mode screen to switch the display status. The
capitalized letter in the softkey indicates the currently selected mode.
HA-R: Horizontal angle right
HA-L: Horizontal angle left
CAllocating [R/L]: "19.6 Allocating Key Functions"
22
5. BASIC OPERATION
Input screen/configuration screen
Display all options
Scroll down for more

items
Values can be input/

edited
"Graphic" tab
Arrow indicates north as set backsight
Target point
Instrument station
Scale
(units: m)
The "Graphic" tab display can be modified using the softkeys in the second page.
[CNFG] : In <Graphic configuration> the user can specify the orientation of the "graphic" tab
display and which point, target or station, to set at the center of the display.
[DEF.] : Returns to the original orientation display.
[ZoomIn] : Zooms in.
[ZoomOut] : Zooms out.
23
5. BASIC OPERATION
Selecting menus
To select a menu, tap the touch panel or press the relevant number key.
Number
Status bar
Indicates the current status of the instrument.

Tapping icons will switch between the relevant options for that item.
Tapping and holding will display a list of all available options for that item and, in certain cases, a
link to the configuration screen for that item.
Status bar
Allocation of the icons of the status bar corresponds with that of Starkey mode.
CAbout icons: "5.4 Starkey Mode"
24
5. BASIC OPERATION
5.3 Inputting Characters using the Input Panel
To display <Input Panel>, tap of status bar/Starkey mode or while pressing {SHIFT} press {α}.
This keyboard can be used to input numeric and alphabetic characters as well as symbols. Tap the
icon again to close.
$
• When <Input Panel> is covering the icon of the status bar, use the stylus pen to drag the input
panel to another part of the screen so that you can access the icon.
Input panel
Esc : Deletes all input characters

Tab : Moves the cursor to the next text box
CAP : Alternates between upper and lower case alphabetic characters and numbers/
symbols
Shift : Alternates between upper and lower case alphabetic characters and numbers/
symbols. Is canceled after inputting a single character.
Ctl : No function
Del/A : Delete the character to the left/right or deletes the entire text in the active section
←→ : Move the cursor left/right
ENT : Accept input characters
Space : Input a blank space
áü : Accesses further Latin/Germanic characters/symbols. Is canceled after inputting a
single character.
25
5. BASIC OPERATION
5.4 Starkey Mode
Via Starkey mode, you can jump from each basic mode screen to the screen of checking/changing the
various settings directly. Press starkey { ★ } to enter Starkey mode. Each icon can be tapped or
pressed and hold in the same way with status bar.
• 12 icons allocated in Starkey mode and the above 8 icons correspond with that status bar
• Allocation of the icons can be changed.
CChanging allocation of Starkey mode: "19.7 Changing Starkey Mode Icons"
(1) (2) (3) (4)
(5) (6) (7) (8)
(9) (10)
(11) (12)
11 and 12 are not allocated
when instrument was shipped.
Indicates the current status of the instrument.

Tapping icons will switch between the relevant options for that item. Tapping and holding will display
a list of all available options for that item and, in certain cases, a link to the configuration screen for
that item. (The numbers correspond to above icons).
(1) Battery icon

Remaining battery power indicator (BDC70/external battery BT-73Q, Temperature = 20°C, EDM
on).
The remaining battery power displayed when distance measurement is in progress may differ to
that displayed at other times.
: Level 3 Full power

: Level 2 Plenty of power remains
: Level 1 Half or less power remains
: Level 0 Little power remains Prepare a replacement battery.
(Flashes red and black)
: No power Stop operation and charge the battery.
(Red display in the center of the screen)
C"6.1 Battery Charging"
26
5. BASIC OPERATION
When using external battery

: Level 3 Full power
: Level 2 Plenty of power remains
: Level 1 Half or less power remains
: Level 0 Little power remains. Prepare a replacement battery.
C"6.1 Battery Charging"
(2) Target type icon

Selection of target type and configuration of prism constant correction value.
: Prism (0mm)
: 360° prism (-7mm)
: Sheet (0mm)
: N-Prism
Target information can be edited/recorded in <Reflector setting>.

C"19.3 EDM Settings PROCEDURE Recording and editing target information"
(3) Motor icon

Configuration of Auto Pointing status. The display may change slightly depending on the target
type selected.
: Auto Pointing ON
: Auto Pointing OFF
: Begin searching
: Rotates the instrument 180°
One of the following icons will be displayed while the motor is in operation to indicate the current
status of the instrument.
: Rotating
: Rotating at fixed velocity
: Searching
$
• Auto Pointing cannot be performed when "Reflectorless" has been selected as the target type.
will be displayed.
• An arrow indicating turn direction will be displayed when the instrument is rotating at a fixed
velocity.
C "11.3 Turning the Instrument from the Reference Angle to a Specified Angle"
27
5. BASIC OPERATION
(4) Laser-pointer/guide light icon

Configuration of laser-pointer/guide light status.
C Switching the laser-pointer/guide light ON/OFF: "5.1 Basic Key Operation"
: Guide light ON
: Guide light OFF
: Laser-pointer ON
: Laser-pointer OFF
$
• The laser-pointer will be automatically switched OFF during distance measurement.
(5) Tilt angle compensation icon

The vertical and horizontal angles are automatically compensated for small tilt errors using the
dual-axis tilt sensor. This icon displays the status of this function.
: Horizontal and vertical tilt angles compensated (blue)

: No compensation
: Only vertical tilt angle compensated (green)
$
• is displayed when the instrument is out of level.
(6) Communication status with external devices icon

Selection and configuration of communication status with external devices. This icon is not
displayed in Program mode.
: Connection via RS232C cable
: Connection via Bluetooth wireless technology (DS set as "Master"
device) (blue antenna)
: Connection via Bluetooth wireless technology (DS set as "Slave"
device) (green antenna)
$
• When Bluetooth communication is selected (DS set as "Master" device) a connection can be
initiated/canceled by tapping / .
28
5. BASIC OPERATION
Connection status to external devices is displayed as follows.

i) Connection via Bluetooth wireless technology
When DS is set as the "Master" device the antenna icon is blue. When the DS is set as the "Slave"
device the antenna icon is green.
: Connecting
: Canceling connection
: (Antenna is moving) Inquiring about other Bluetooth devices
: (Antenna is stationary) Communication settings in progress/Preparing for

communication (Instrument just powered ON or just switched to "Slave")
: Connection error (icon flashes) (the color depends on the setting)
ii) : Connection via RS232C cable
$
• An arrow (e.g. / ) is displayed to indicate that data transmission is in progress. A red
arrow indicates that data transmission has failed and data needs to be sent again.
(7) Input mode icon

Selection of input mode
_1 Inputting numbers and symbols

_a Inputting lower case alphabetic characters
_A Inputting upper case alphabetic characters
C"5.1 Basic Key Operation I Inputting letters/figures"
(8) Input panel icon

C "5.3 Inputting Characters using the Input Panel"
(9) PPM setting icon

Current atmospheric correction factor setting is displayed.
Configuration of EDM.
(10) Config mode icon

Switch to Config mode.
C"19. CHANGING THE SETTINGS"
29
5. BASIC OPERATION
(11) Touch panel icon

C"19.7 Changing Starkey Mode Icons"
:Touch panel temporarily de-activated.
$
• This icon cannot be operated during distance measurement, or during data transmission.
(12) Disk usage icon
Tap and hold disk icon in the status bar to check the detail of the disk usage.
C"19.7 Changing Starkey Mode Icons"
: Less than 20%
: 20 to 50%
: More than 50%
Internal Disk
Used space : Usage space of disk capacity of the instrument
Free space : Free space of disk capacity of the instrument
Capacity : Disk capacity of the instrument
Removable Disk
Used space : Usage space of disk capacity of the external disk connected to the
instrument
Free space : Free space of disk capacity of the external disk connected to the
instrument
Capacity : Disk capacity of the external disk connected to the instrument
G
• "Removable Disk" is displayed only when an external disk is connected to the instrument.
30
5. BASIC OPERATION
5.5 Using the Program Selection Screen
The program selection screen displays a list of all programs installed on the instrument. Each screen
page contains a maximum of 5 program icons. When multiple screen pages exist, navigating between
pages is possible using the arrows that appear at the left/right of the screen.
An icon without an
be selected
Navigating between pages
The previous/next screen page can be displayed by pressing {O}/{G}/{L}/{K}, or that appear at the
left/right of the screen.
Previous page Next page
31
6. USING THE BATTERY
6.1 Battery Charging
The battery was not charged at the factory. Charge the battery fully before using the instrument.
G
• The charger will become rather hot during use. This is normal.
• Do not use to charge batteries other than those specified.
• The charger is for indoor use only. Do not use outdoors.
• Batteries cannot be charged, even when the charging lamp is flashing, when the temperature is
outside the charging temperature range.
• Remove batteries from the charger before putting into storage.
• When not in use, disconnect the power cable plug from the wall outlet.
• Store the battery in a dry room where the temperature is within the following ranges. For long-term
storage, the battery should be charged at least once every six months.
Storage period Temperature range

1 week or less -20 to 50°C
1 week to 1 month -20 to 45°C
1 month to 6 months -20 to 40°C
6 months to 1 year -20 to 35°C
• Batteries generate power using a chemical reaction and as a result have a limited lifetime. Even
when in storage and not used for long periods, battery capacity deteriorates with the passage of
time. This may result in the operating time of the battery shortening despite having been charged
correctly. In this event, a new battery is required.
PROCEDURE
1. Connect the power cable to the charger and

plug the charger into the wall outlet.
2. Mount the battery in the charger by matching

the grooves on the battery with the guides on
the charger.
Grooves
Guides
Slot 1
Charging
lamp
Slot 2
3. When charging starts, the lamp starts blinking.
4. The lamp lights when charging is finished.
32
5. Remove the battery and unplug the charger.
$
• Slots 1 and 2:
The charger starts charging the battery mounted
first. If you place two batteries in the charger, the
battery in slot 1 is charged first, and then the
battery in slot 2. (C step 2)
• Charging lamp:
The charging lamp is off when the charger is
outside the charging temperature range or when the battery is mounted incorrectly. If the lamp is still
off after the charger falls within its charging temperature range and the battery is mounted again,
contact your local dealer. (Csteps 2 and 3)
• Charging time per battery (at 25°C):
BDC70:about 5.5 hours
6.2 Installing/Removing the Battery
Mount the charged battery.

C Type of power source: "22. POWER SUPPLY SYSTEM"
G
• Use the attached battery (BDC70).
• Before removing the battery, turn off the power to the instrument. If the battery is removed while the
power is switched on, a warm boot may occur. File and folder data may be lost as a result.
• Do not open the battery cover while the power is on.
• Do not damage the projected sensor inside the battery cover. Also, be careful not to shut the battery
cover on your fingers.
• When installing/removing the battery, make sure that moisture or dust particles do not come in
contact with the inside of the instrument.
• Remove batteries from the surveying instrument or charger before putting into storage.
PROCEDURE Mounting the battery
1. Slide down the catches on the battery cover to

open.
Battery cover
33
2. Insert the battery in the direction of the arrow

on the side of the battery.
G
• Do not insert the battery inclined. Doing so
may damage the instrument or battery
terminals.
3. Close the battery cover. A click is heard when

the cover is secure.
Battery
34
7. SETTING UP THE INSTRUMENT
G
• Mount the battery in the instrument before performing this operation because the instrument will tilt
slightly if the battery is mounted after levelling.
7.1 Centering
PROCEDURE Centering with the optical plummet eyepiece
1. Make sure the legs are spaced at equal

intervals and the head is approximately level.
Set the tripod so that the head is positioned over
the survey point.
Make sure the tripod shoes are firmly fixed in the
ground.
2. Place the instrument on the tripod head.

Supporting it with one hand, tighten the centering
screw on the bottom of the unit to make sure it is
secured to the tripod.
Centering screw
3. Looking through the optical plummet eyepiece, Focussing on the survey point
turn the optical plummet eyepiece to focus on
the reticle.
Turn the optical plummet focussing ring to focus
on the survey point.
Focussing on
the reticle
35
PROCEDURE Centering with the laser plummet (Option)
1. Set up the tripod and affix the instrument on the

tripod head.
C"7.1 Centering"
2. Press { } to power on
C"8. POWER ON/OFF"
The electric circular level is displayed on the <Tilt>.
3. Press [L-ON].
The laser plummet beam will be emitted from the
bottom of the instrument.
4. Use [-]/[+] on the second page to adjust the

brightness of the laser.
5. Adjust the position of the instrument on the tripod

until the laser beam is aligned with the center of the
survey point.
6. Press [L-OFF] to turn the laser plummet off.

Alternatively, press {ESC} to return to another
screen. The laser plummet will switch off
automatically.
36
$
• Visibility of the laser spot may be affected when operating in direct sunlight. In this event, provide
shade for the survey point.
7.2 Levelling
PROCEDURE
1. Adjust the levelling foot screws to center the

survey point in the optical plummet reticle.
2. Center the bubble in the circular level by either

shortening the tripod leg closest to the offcenter
Tripod legs
direction of the bubble or by lengthening the tripod adjustment
leg farthest from the offcenter direction of the
bubble. Adjust one more tripod leg to center the
bubble.
Turn the levelling foot screws while checking the

circular level until the bubble is centered in the
center circle.
3. Power ON the instrument.

C"8. POWER ON/OFF"
The electric circular level is displayed on the <Tilt>.
“z” indicates the bubble in circular level. The range
of the inside circle is ±1.5' and the range of the
outside circle is ±6'.
4. Center “z” in the circular level.

When the bubble is in the center, proceed to step
7.
37
5. Turn the instrument until the telescope is parallel

to a line between levelling foot screws A and B.
6. Set the tilt angle to 0° using foot screws A and B

for the X direction and levelling screw C for the Y
direction.
7. Loosen the centering screw slightly.

Looking through the optical plummet eyepiece, slide
the instrument over the tripod head until the survey
point is exactly centered in the reticle.
Retighten the centering screw securely.
If the instrument is levelled using laser plummet,

emit the laser plummet beam and check it again.
C"7.1 Centering PROCEDURE Centering with
the laser plummet (Option)"
8. Check again to make sure the bubble in the electric

circular level is centered.
If not, repeat the procedure starting from step 6.
9. Press {ESC} to return to Observation mode.
38
8. POWER ON/OFF
G
• When the power cannot be switched ON or the power is soon turned OFF even though the battery
is mounted, there may be almost no battery power remaining. Replace it with a fully charged battery.
C"20. WARNING AND ERROR MESSAGES"
PROCEDURE Power ON
1. Press { }.
When the power is switched on, the Tilt screen is
displayed.
Press {ESC} to go to Observation mode screen.
If "Out of range" is displayed, the instrument tilt

sensor is indicating that the instrument is out of level.
Level the instrument once again using circular level,
then the tilt screen will be displayed.
$
• "Tilt crn." in "Obs. condition" should be set to "No" if the display is unsteady due to vibration or strong
wind.
C "19.1 Observation Conditions"
& Resume function

The Resume function redisplays the screen appearing before the instrument was powered OFF
when the instrument is powered back ON. All parameter settings are also saved. Even if
remaining battery power is completely depleted, this function will remain active for 1 minute,
after which it is canceled. Replace a depleted battery as soon as possible.
PROCEDURE Power OFF
1. Press and hold (about 1sec) { }.
G
• When there is almost no battery power remaining,
the battery icon in the status bar will start to blink.In
this event, stop measurement, switch off the power
and charge the battery or replace with a fully
charged battery.
• To save power, power to the instrument is
automatically cut off if it is not operated for a fixed
period of time. This time period can be set in
"Power off" in <Inst.config.>.
C"19.2 Instrument Configuration"
39
8. POWER ON/OFF
8.1 Configuring the Touch Panel
When using for the first time, or after performing a cold

boot, the screen for configuring the touch panel will be
displayed.
Follow the instructions on the screen. Tap the cross-

hairs at the center of the display with the stylus pen.
Tap 5 times. Press {ENT} to complete touch panel
configuration. Press {ESC} to retain previous settings.
$
• Touch panel configuration can be performed at any
time during normal operation by pressing [PNL
CAL] in <Inst.config.>.
8.2 Resolving Software Issues
If you are experiencing problems with the instrument and suspect a fault in the program, you should
try a warm boot. If the problem is not resolved with a warm boot the next step is to perform a cold boot.
A warm boot will not erase surveying data in the instrument but will cancel the resume function.
Whenever possible transmit the data to a personal computer before rebooting.
PROCEDURE
1. Power OFF the instrument.
2. Press { } while pressing {ENT}.

The instrument is reset and powers ON as normal.
& Cold boot

If the problem is not resolved with a warm boot the next step is to perform a cold boot. A cold
boot will not erase surveying data in the instrument but all the parameters will be changed to the
factory settings. If the data in the memory is necessary, BE SURE TO TRANSFER IT TO A
PERSONAL COMPUTER BEFORE PERFORMING A COLD BOOT.
To perform a cold boot, while holding { }, and {S.P.}, press { }.
The instrument is reset and powers ON as normal.
C "19.11 Restoring Default Settings"
40
8. POWER ON/OFF
& Problems Powering OFF

When the instrument cannot be powered OFF as normal, depress the reset button with the tip
of the stylus pen.
G
• Pressing the Reset button may result in file and folder data being lost.
Reset button
8.3 Powering ON/OFF from an External Instrument
The instrument can be powered ON/OFF from an external device such as a computer or data collector.
G
• The password must be input after powering ON the instrument from an external device when a
password has been set.
C Remote PWR-On function: "19.2 Instrument Configuration", Setting a password:
"19.9 Changing Password"
41
9. CONNECTING TO EXTERNAL DEVICES
The instrument supports Bluetooth wireless technology and RS232C for communication with data
collectors etc. Inputting/outputting data is also possible by inserting a USB memory or by connecting
to a USB device. Read this manual in conjunction with the operator’s manual for the relevant external
device.
G
• When doing Bluetooth communication, read "4.3 Bluetooth Wireless Technology".
9.1 Wireless Communication using Bluetooth Technology
The Bluetooth module incorporated in the instrument can be used for communication with Bluetooth
devices such as data collectors.
& Bluetooth connections

Communication between a pair of Bluetooth devices requires one device to be set as the
"Master" and the other as the "Slave". To initiate connections from the DS side, set the DS as
the "Master" device. To initiate connections from the paired device side, set the DS as the
"Slave" device. The factory setting is "Slave".
PROCEDURE Necessary settings for Bluetooth communication
1. Select "Comms" in Config mode. Set Comms

mode in the "Comms setup" tab to "Bluetooth".
G
• Changing communication settings during
Bluetooth communication will cancel the
connection.
• The status bar icon cannot be tapped in
<Communication Setup>.
Items set and options (*: Factory setting)

(1) Comms mode : RS232C*/Bluetooth
(2) Check sum : yes/No*
(3) Controller : Remote/2 Way/2
Way+Remote*
(4) REC Type : REC-A* (newly measured
data is output)/REC-B
(displayed data is output)
(5) Terminate & : ETX*/ETX+CR/ETX+CR+LF
(6) MOTOR State : On (with search state
information)/Off*
(7) Ack mode & : On*/Off
42
& Terminate
Select the option Off or On for carrige return (CR) and line feed when collecting measurement
data with a computer.
& ACK mode

When communicating to an external device, the protocol for handshaking can omit the [ACK]
coming from the external device so data is not sent again.
On : Standard
Off : Omit the [ACK]
$
• Setting’ (5) and (7) are for an instrument using
GTS commands.
2. Select a mode for the DS in the "Bluetooth" tab.

The factory setting is "Slave".
Register companion devices.
• "Master" cannot be selected when no
companion devices have been registered.
C "Master"/"Slave": "& Bluetooth
connections"
3. Select, in "Link", a companion device from among

the Bluetooth devices already registered in the
instrument.
C Registering devices: "PROCEDURE
Registering Bluetooth companion devices"
• Companion devices cannot be selected when

the DS is set as "Slave".
4. Set "Authentication" to "Yes" or "No".

If "Authentication" is set to "Yes" for the DS the
passkey will also need to be input on the
companion device.
43
5. When "Authentication" is set to "Yes", input the

same passkey as that for the intended companion
device. Even if "Authentication" is set to "No", a
passkey is requested when authentication is set
on the companion device being used.
• Up to 16 numeral characters can be input. Input

characters will be displayed as asterisks (e.g.
"*****"). The passkey was set to "0123" at the
factory.
6. Press [OK] to finish settings.
PROCEDURE Registering Bluetooth companion devices
1. Power on the companion device.
2. Select "Bluetooth" in "Comms mode" in the

"Comms setup" tab.
3. Press [LIST] to display a list of all registered

devices.
Register the data collectors to use in "Serial" tab

and devices to use with the Dial-Up Program in
"Dial-up" tab.
$
• Maximum number of devices registered: 6
4. Register your Bluetooth device(s).
44
• Press [Add] to display <Add device>. Input the

device name and Bluetooth address and press
[OK]. Both should be 12 characters (numbers 0
to 9 and letters from A to F) in length.
• Press [Search] to search about Bluetooth

devices in the immediate vicinity of the
instrument and display their device name and
address in a list. Select a device from this list and
press [OK] to add to the Link device list in step 3.
• Press [Delete] to delete the selected device

name. Deleted device names cannot be
retrieved.
• Select a device and press [Edit] in the second

page to update the device name and/or device
address.
5. Press [OK] to complete registration and return to

the screen in step 2.
PROCEDURE Displaying Bluetooth information for the DS
1. Select "Comms" in Config mode.
2. Press [Info] in the "Bluetooth" tab to display

information for the DS. Register the Bluetooth
address (BD ADDR) displayed here in the paired
device set as "Master".
& Bluetooth device address

This is a number unique to one particular Bluetooth device used to identify devices during
communication. This number consists of 12 characters (numbers 0 to 9 and letters from A to F).
Some devices may be referred to by their Bluetooth device address.
45
9.2 Communication between the DS and Companion Device
G
• Bluetooth communication causes instrument battery power to be depleted at a rate higher than that
for normal operation.
• Check that the companion device (data collector, computer, or cellular phone etc.) is turned on and
the relevant Bluetooth settings are complete.
• All communication settings will be changed to factory settings when a cold boot is performed.
Comms setup will need to be performed again.
C"9.1 Wireless Communication using Bluetooth Technology"
PROCEDURE Bluetooth communication
1. Complete the necessary DS settings for

Bluetooth communication.
C "9.1 Wireless Communication using
Bluetooth Technology"
2. Start communication
When DS is set as the "Master" device, the
[Connect] softkey is allocated to the fourth page
of Observation mode. When [Connect] is pressed
the DS searches for the device selected in "Link"
and a connection starts. When a connection has
been successfully established is displayed
in the status bar.
The establishing of a connection can also be
initiated by tapping in the status bar.
C Communication status:"5.4 Starkey Mode"
$
• When DS is set as the "Slave" device, the
establishing of a connection can only be
initiated/canceled by the companion device set
as "Master".
3. Press [Cancel] in the fourth page of Observation

mode to terminate the connection.
A connection can also be terminated by tapping
in the status bar.
46
9.3 Connection via RS232C Cable
RS232C communication is possible, connecting instrument and a data collector with the cable.
PROCEDURE Basic cable settings
1. Power OFF the instrument and connect the

instrument and a data collector with a interface
cable.
C Cables: "24. OPPTIONAL ACCESSORIES"
2. Select "Comms" in Config mode.

Set communication conditions in the "Comms
setup" tab. Set "Comms mode" to "RS232C".
3. Set options in the "RS232C" tab according to the

selection made in the "Comms setup" tab.

(1) Baud rate: 1200/2400/4800/9600*/19200/
38400bps
(2) Data bits: 7/8* bits
(3) Parity : Not set*/Odd/Even
(4) Stop bit : 1*/ 2 bits
4. Press [OK] to finish settings.
47
9.4 Connecting via USB Cable
Using USB port 2, the instrument and a computer can be communicated. There are USB mode and
Mobile mode.
& USB port

The instrument has two different USB ports. Each port is used for connection to different types
of devices.
Port name Device type

USB port 1 USB memory device.
USB port 2 (mini-B) computers etc.
USB port 1
USB port 2 (mini-B)
G
• TOPCON CORPORATION cannot guarantee that all USB devices are compatible with the DS USB
ports.
• Use a computer WindowsXP/Vista/7 is based and USB connection is capable.
• Remove the USB cable from USB port 2 carefully to avoid damaging the cable.
$
• As for the download and install of "exFat file system driver"/ActiveSync/Windows Mobile Device
Center, please access to Microsoft support site.
48
PROCEDURE Connecting the instrument to a computer to transfer data from instrument in

USB mode
When connecting Windows XP, "exFat file system driver" needs to be installed to the computer.
1. Open the external interface hatch by sliding its

button.
External interface
hatch
2. Power OFF the instrument. Connect the USB port

2 on the instrument and computer using the USB
cable.
C "8. POWER ON/OFF"
$
• The computer does not need to be turned OFF
before connection.
USB port 2
3. Press { } while pressing {ENT} to display a
message box asking whether to boot USB mode,
then press [YES].
The screen of the instrument will be <USB Mode>.
$
• instrument may not be displayed as
<Removable Disk>. It depends on Windows
settings.
G
Follow the instructions below to ensure that the
instrument continues to operate normally during
USB transfer.
• Do not change the folder hierarchy or folder
names in <Removable Disk>.
• Do not format the "removable disk" on the
computer.
49
4. Perform "Safely Remove Hardware" in the

task bar and disconnect the USB cable.
5. Press { } and hold (about 1sec) to turn off the

instrument to exit USB mode connection.
PROCEDURE Connecting the instrument to a computer to transfer data from instrument in

Mobile mode
A synchronous software needs to be installed to the computer depending on the Windows version.
Computer to connect Synchronous software

Windows XP ActiveSync
Windows vista/7 Windows Mobile Device Center
1. Slide up the catch on the external interface hatch

to open.
2. Power OFF the instrument. Connect the

instrument and computer using the USB cable.
C "8. POWER ON/OFF"
$
• The computer does not need to be turned OFF
before connection.
3. Press { } while pressing {ENT} to display a

message box asking whether to boot USB mode,
then press [NO].
The synchronous software is effective.
$
• instrument may not be displayed as
<Removable Disk>. It depends on Windows
settings.
G
Follow the instructions below to ensure that the
instrument continues to operate normally during
USB transfer.
• Do not change the folder hierarchy or folder
names in <Removable Disk>.
• Do not format the "removable disk" on the
computer.
50
4. If synchronous software displays a partner setting

screen on the computer and asks whether to set a
partner device, press [NO].
$
• A partner setting screen may not be displayed
depending on the synchronous software
settings.
5. Disconnect the USB cable to exit mobile mode

connection.
9.5 Inserting USB Memory
Saving data in a USB memory or importing data from a memory is possible using the particular
program on program mode.
C USB ports: "9.4 Connecting via USB Cable"
G
• When reading/writing data, do not remove the USB memory.
PROCEDURE
1. Slide up the catch on the external interface hatch
to open.
C "9.4 Connecting via USB Cable"
2. Insert the USB memory into the USB port 1.

USB Port 1
G
• When using a USB memory with 4 metal
terminals on the surface, insert it with the
terminal facing backwards to avoid damaging
the USB port.
3. Close the external interface hatch until a click is

heard.
4. Save data in the USB memory or import data from

the memory.
C Program Explanations of each program
51
10.TARGET SIGHTING
A target can be automatically sighted using the Auto Pointing function or manually sighted by the
operator using the sighting collimatorand telescope.
When Auto Pointing is performed, the image sensor on the
Offset
of Y direction
instrument detects the light beam reflected from the target (prism
of X direction
or reflective sheet target), the offset between the target and
telescope reticle is calculated by image processing, then the angle
Offset
measurement value obtained from the encoder is compensated.
There is a possibility that the target and telescope reticle are not
aligned.
C Caution
• The instrument emits a laser beam until the prism is sighted.
G
• Auto Pointing can only be performed when a prism or sheet is used as the target. For reflectorless
measurement, the target must be sighted manually.
• Use designated reflective prisms/reflective sheets for higher precision measurement. Make sure
reflector type and aperture/sheet size are set correctly in <EDM configurations>.
• Detach the handle if the prism is located at the zenith.
C"4.1 Parts of the Instrument Handle L Detaching/attaching the Handle"
• Auto Pointing may take long time if the prism is located at the zenith. In this case, use optional
accessory diagonal eyepiece (DE27) and manually sight the target.
C"10.3 Manually Sighting the Target"
• If more than one prism is located in the field of sight during Auto Pointing, an operation error will
occur and the instrument will not be able to find the target.
• A prism beyond glass cannot be searched because a measurement error occurs.
• If an obstacle blocks the laser beam path between the instrument and the prism, instrument cannot
find the target correctly.
• If strong light shines directly into the objective lens, measurement cannot be performed correctly.
• Position every target in alignment with the objective lens to eliminate the error caused by tilted
target.
C(Facing the 360° prism toward the instrument: "26.1 High Accuracy with the 360° Prism"
• The following table suggests what size target to use for different distances when performing Auto
Pointing with a reflective sheet target.
Distance Target size
5 to 15m RS10 (10mm)
5 to 30m RS30 (30mm)
5 to 40m RS50 (50mm)
10 to 50m RS90 (90mm)
52
10. TARGET SIGHTING
10.1 Auto Pointing Settings
PROCEDURE
1. Select "Motor" in <Configuration>.
Set Auto Pointing functions in the Configuration
tab.
Set "Search Setting" to "Search".

(1) AUTO AIM & : Fine/Rapid*
(2) Search Setting : None/Search*
(3) TURN & : 5"/10"*/20"/30"/60"
& AUTO AIM

When the target enters the field-of-view within the set limit for Auto Pointing completion (the limit
differs between "Fine" and "Rapid"), the instrument starts acquiring data (the amount of data
differs between "Fine" and "Rapid") then completes the Auto Pointing by calculating the data.
Set to "Fine" for greater accuracy during Auto Pointing. Make sure that the prism is securely
mounted on a tripod etc.
Set to "Rapid" when supporting the pole by hand.
When "Fine" is set the instrument checks that the prism position is stable, then searches for the
prism direction. Once the instrument confirms that the prism is sighted at the approximate center
of the field-of-view, Auto Pointing is complete. Although this setting provides greater accuracy,
when supporting the pole by hand, hand movements will result in Auto Pointing taking too long
to complete and a "Time out" error will occur.
When "Rapid" is set however, Auto Pointing can be performed even with slight instability of prism
position or minor shifts of target position in the field-of-view. The instrument will use the data
obtained to determine the direction of the target.
Auto Pointing performed using the "Rapid" setting can be completed in a much quicker time than
the "Fine" setting.
"Fine" is recommended when a high level of measurement accuracy is needed. The range for
the offset between the target and reticle after Auto Pointing completed changes as shown below
depending on the Srch. accuracy setting.
53
10. TARGET SIGHTING
& TURN
This option allows the user to set a tolerance range for setting accuracy (after rotation to a
specified angle). For example, when this option is set to 30" and [INV], [H.ANG], or [ROTATE]
is pressed, the instrument will stop rotation within 30" of the specified rotation angle.
& Search operation during Auto Pointing

When the target enters the field-of-view within the set limit (setting of "Auto AIM" and "Measure
Acc.") for Auto Pointing completion, the instrument stops moving, calculates the offset between
the target and telescope reticle by image processing, then compensates the angle measurement
value obtained from the encoder. This compensation enables accurate sighting in a short time.
Even though the target and telescope reticle may appear to be misaligned, actual angle value
of center of the target is displayed. Compensated values are displayed in blue.
If the instrument is rotated (manually or using the Jogs) more than 10", compensation will be
canceled, the angle reverts to that obtained from the encoder, and the angle values are once
again displayed in black. Powering OFF the instrument will cancel the compensation function.
2. Set the area in which to perform target sighting in

the Search area tab.
Angle values can only be specified in 1°steps.
Input values not conforming to this format will be
automatically rounded up.

(1) Vertical : 0 to 90° (15*)
(2) Horizontal : 0 to 180° (15*)
3. Set the Jog turning speed for vertical and

horizontal rotation of the telescope. The "Shift"
point signifies the Jog turning speed at which
telescope rotation switches from the Lo speed
setting to the Hi speed setting.The higher the
"Shift" point setting, the faster the Jog turning
speed needed to activate the Hi speed setting.

(1) Lo : 1 to 4 (3*) (steps. 4 is fastest)
(2) Hi : 1 to 7 (4*) (steps. 7 is fastest)
(3) Shift : 1 to 6 (2*) (steps)
Press [INIT] to return JOG Setting tab settings

only to their factory settings.
4. Press [OK].
54
10. TARGET SIGHTING
10.2 Auto-Pointing Function for Target Sighting
PROCEDURE
1. Use the sighting collimator to aim the objective

lens in the general direction of the target. The
vertical and horizontal Jogs can be used for
precise adjustments of the instrument and
telescope
C JOG Setting tab: "10.1 Auto Pointing
Settings" step 3.
2. Press [SRCH] in any Observation mode screen.

The telescope and top half of the instrument
rotate and target auto-search begins. When the
target is found, the instrument sights the prism
and stops.
CAllocating the [SRCH] softkey:
"19.6 Allocating Key Functions"
55
10. TARGET SIGHTING
10.3 Manually Sighting the Target
G
• When sighting the target, strong light shining directly into the objective lens may cause the
instrument to malfunction. Protect the objective lens from direct light by attaching the lens hood.
Observe to the same point of the reticle when the telescope face is changed.
PROCEDURE
1. Focus on the reticle

Look through the telescope eyepiece at a bright
and featureless background.
Turn the eyepiece screw clockwise, then
counterclockwise little by little until just before
the reticle image becomes focussed.
Using these procedures, frequent reticle
refocussing is not necessary since your eye is
focussed at infinity.
2. Sight the target

Use the Sighting collimator to bring the target
into the field of view. Turn the vertical and
horizontal Jogs for fine sighting adjusting.
3. Focus on the target

Turn the telescope focussing ring to focus on
the target.
Turn the vertical and horizontal fine motion
screws to align the target with the reticle.
The last adjustment of each fine motion screw
should be in the clockwise direction.
4. Readjust the focus until there is no parallax

Readjust the focus with the focussing ring until
there is no parallax between the target image
and the reticle.
& Eliminating parallax

This is the relative displacement of the target image with respect to the reticle when the
observer’s head is moved slightly before the eyepiece.
Parallax will introduce reading errors and must be removed before observations are taken.
Parallax can be removed by refocussing the reticle.
56
10. TARGET SIGHTING
& Sighting manually

When sighting manually, set "Search Setting" to "None" in <Motor Configuration> Configuration
tab, then use the Sighting collimator to bring the target into the field of view. When the target is
in the field-of-view, use the Jogs to make fine adjustments and accurately sight the center of the
prism.
It is recommended that a slow Jog turning speed is used for greater stability when performing
fine adjustments.
57
11.ANGLE MEASUREMENT
This section explains the procedures for basic angle measurement in Observation mode.
• It is possible to allocate softkeys in measurement menus to suit various applications and the ways
that different operators handle the instrument.
C"19.6 Allocating Key Functions"
11.1 Measuring the Horizontal Angle between Two Points

(Horizontal Angle 0°)
Use the “0SET” function to measure the included angle between two points. The horizontal angle can
be set to 0 at any direction.
PROCEDURE
1. Sight the first target as at right.

C"10. TARGET SIGHTING"
2. In the first page of Observation mode, press

[0SET].
[0SET] will flash, so press [0SET] again.
The horizontal angle at the first target becomes 0°.
3. Sight the second target.
The displayed horizontal angle (HA-R) is the

included angle between two points.
58
11. ANGLE MEASUREMENT
11.2 Setting the Horizontal Angle to a Required Value (Horizontal

Angle Hold)
You can reset the horizontal angle to a required value and use this value to find the horizontal angle
of a new target.
PROCEDURE
1. Sight the first target.
2. In the second page of Observation mode, press

[H-SET]. <Set H angle> is displayed.
3. Enter the angle you wish to set, then press [OK]. Current angle
The value that is input as the horizontal angle is
displayed.
• The same setting can also be performed with

coordinate and azimuth input.
C "13.2 Azimuth Angle Setting"
4. Press [OK] to confirm the input value and display

the new horizontal angle.
5. Sight the second target.

The horizontal angle from the second target to the
value set as the horizontal angle is displayed.
$
• Pressing [HOLD] performs the same function as above.
• Press [HOLD] to set the displayed horizontal angle. Then, set the angle that is in hold status to the
direction you require.
CAllocating [HOLD]: "19.6 Allocating Key Functions"
59
11.3 Turning the Instrument from the Reference Angle to a

Specified Angle
The instrument automatically turns from the reference direction to the specified angle (target).
• instrument also turns to the target coordinates when reference angle is omitted.
G
• Rotation may not be completed correctly when specifiying an angle near the zenith or nadir if "Tilt
crn." or "Coll. crn" is set to "Yes" in "Obs.condition".
PROCEDURE
1. Sight the point you will use as the reference angle

and set it as the reference angle.
Sight the reference point and press [0SET], or
input the reference point angle.
C"11.1 Measuring the Horizontal Angle
between Two Points (Horizontal Angle 0°)"/
"11.2 Setting the Horizontal Angle to a
Required Value (Horizontal Angle Hold)"
2. Press [MOTOR] in the first page of Observation

mode and enter the vertical and horizontal angles
in the Motor tab.
• Desired angle can be calculated by inputting the

coordinates of station point and target point.
Press [COORD] in the second page and set
station point. Press [OK] to calculate the angle.
3. After confirming the angle, press [ROTATE]. The

instrument moves to the point (target) entered in
step 2.
• The following operation can be select in the

second page.
[COORD] : set the angle by coordinates
[INV]: : rotate the top of the instrument
and telescope 180°
[CNFG]: : set motor settings
C"10.1 Auto Pointing Settings"
60
& Fixed velocity rotation

The instrument horizontal angle and telescope can be rotated using the controls in the Fixed
velocity rotation tab. Speed settings are from 1 to 16. Allocate [Fix Vel] in Observation mode to
use this function.
Tap the touch panel in the desired rotation direction.
Tap the red center circle/ in the status bar or to press {ESC} to stop rotation.
11.4 Angle measurement and Outputting the Data
The following explains angle measurement and the features used to output measurement results to a
computer or other external devices.
C"9. CONNECTING TO EXTERNAL DEVICES", Cables: "24. OPPTIONAL ACCESSORIES",
Output format and command operations: "Communication manual"
PROCEDURE
1. Connect instrument and external device.
2. Allocate the [HVOUT-T] or [HVOUT-S] softkey to

the OBS mode screen.
$
• Pressing the softkey outputs data in the following
format.
[HVOUT-T] : GTS format
[HVOUT-S] : SET format
3. Sight the target point.
4. Press [HVOUT-T] or [HVOUT-S].

Output measurement data to peripheral
equipment.
61
12.DISTANCE MEASUREMENT
Perform the following settings as preparation for distance measurement in Observation mode.
• Distance measurement mode
• Target type
• Prism constant correction value
• (Target) Aperture
• ppm
• Search area
• Auto Pointing
C"10.1 Auto Pointing Settings", "19.3 EDM Settings"
C Caution
• When using the laser-pointer function, be sure to turn OFF the output laser after distance
measurement is completed. Even if distance measurement is canceled, the laser-pointer function is
still operating and the laser beam continues to be emitted.
G
• Make sure that the target setting on the instrument matches the type of target used. The instrument
automatically adjusts the intensity of the laser beam and switches the distance measurement
display range to match the type of target used. If the target does not correspond to the target
settings, accurate measurement results cannot be obtained.
• Accurate measurement results cannot be obtained if the objective lens is dirty. Dust it off with the
lens brush first, to remove minute particles. Then, after providing a little condensation by breathing
on the lens, wipe it off with the wiping cloth.
• During reflectorless measurement, if an object obstructs the light beam used for measurement or an
object with a high reflective factor (metal or white surface) is positioned behind the target, accurate
measurement results may not be received.
• Scintillation may affect the accuracy of distance measurement results. Should this occur, repeat
measurement several times and use the averaged value of the obtained results.
12.1 Returned Signal Checking
Check to make sure that sufficient reflected light is returned by the target sighted by the telescope.
Checking the returned signal is particularly useful when performing long distance measurements.
C Caution
• The laser beam is emitted during returned signal checking.
G
• When the light intensity is sufficient even though the center of the reflective prism and the reticle are
slightly misaligned (short distance etc.), “I” will be displayed in some cases, but in fact, accurate
measurement is impossible. Therefore make sure that the target center is sighted correctly.
62
12. DISTANCE MEASUREMENT
PROCEDURE
1. Accurately sight the target.
2. Press [S-LEV] in observation mode.

<Aiming> is displayed.
CAllocating [S-LEV]: "19.6 Allocating Key
Functions"
When [S-LEV] is pressed, a gauge indicating light

intensity is displayed.
• The more displayed, the greater the
quantity of reflected light.
• If “I” is displayed, only enough light for the
measurement is returned.
• When “I” is not displayed, accurately resight the
target.
[BEEP]/[OFF] : Sets a buzzer sound when
measurement is possible.
Press to switch on and off.
[MEAS] : Returns to Observation
mode and starts angle and
distance measurement
regardless of "Search
Setting" setting.
3. Press [OFF] to finish signal checking.

Press {ESC} or tap the cross in the top-right
corner to return to the previous screen.
$
• When is displayed persistently, but “I” is not, contact your local dealer.
• If no key operations are performed for two minutes, the display automatically returns to the previous
screen.
63
12.2 Using the Guide Light in Distance Measurement
The color and flashing speed of the guide light indicates the status of the instrument and can be known
when the user is located at a distance from the instrument.
CSwitching the guide light ON/OFF "5.1 Basic Key Operation"
• The pattern of the guide light can be changed.

G
• Even if the guide light is set to ON, the guide light is OFF during distance measurement with the
target type "N-Prism" or returned signal checking.
I Guide light status and meaning

Status of the instrument
simultaneously)
Searching in progress
Fast flashing (Red and green
Measuring (continuous measurement)
simultaneously)
Distance measurement error (no signal, sighting error)
Green and red alternate flashing
Search error (error screen only)
64
12.3 Distance and Angle Measurement
An angle can be measured at the same time as distance.
• The search range can be set.

C Caution
• The laser beam is emitted during Auto Pointing.
PROCEDURE
1. Face the instrument in the direction of the target

Use the sighting collimator to aim the instrument
and telescope toward the target.
C"10. TARGET SIGHTING"
2. Start measurement.
Press [MEAS] in the first page of Observation
mode to start measurement.
The measured distance data (SD), vertical angle

(ZA), and horizontal angle (HA-R) are displayed.
3. Press [STOP] to quit distance measurement.
$
• If the single measurement mode is selected, measurement automatically stops after a single
measurement.
65
• During fine average measurement, the distance data is displayed as SD1, SD2,... to SD9. When the
designated number of measurements has been completed, the average value of the distance is
displayed in the "SDA" line.
• If the tracking measurement is conducted with the target type "N-Prism", the measured data for a
distance exceeding 250m is not displayed.
• The distance and angle that are most recently measured remain stored in the memory until the
power is off and can be displayed at any time by pressing [CALL].
C Allocating [CALL]: "19.6 Allocating Key Functions"
12.4 Distance Measurement and Outputting the Data
The following explains distance measurement and the features used to output measurement data to
a computer or external devices.
C"9. CONNECTING TO EXTERNAL DEVICES", Communication cables: "24. OPPTIONAL
ACCESSORIES". Output format and command operations: "Communication manual"
PROCEDURE
1. Connect instrument and external device.
2. Sight the target point.
3. Press [HVDOUT-T] or [HVDOUT-S] to measure

the distance and output the data to the external
device.
4. Press [STOP] to stop outputting data and return

to Obs Mode.
66
12.5 REM Measurement
An REM measurement is a function used to measure the height to a point where a target cannot be
directly installed such as power lines, overhead cables and bridges, etc.
The height of the target is calculated using the following formula.
Ht = h1 + h2
h2 = S sin z1 x cot z2 - S cos z1
Zenith
Zenith
PROCEDURE
1. Set the target directly under or directly over the

object and measure the target height with a tape
measure etc.
Press [HT] and enter the target height.
2. Select "REM" in <Menu>.
67
3. Sight the target and press [MEAS] to start

measurement. Press [STOP] to stop the
measurement.
The measured distance data, vertical angle and

horizontal angle are displayed.
4. Sight the object, then press [REM] to start REM

measurement is started. The height from the
ground to the object is displayed in "Ht.".
Press [STOP] to stop the measurement.
• To re-observe the target, sight the target then

press [MEAS].
• To continue REM measurement, press [REM].
$
• When measurement data already exists, select "REM" in <Menu> as in step 2 to proceed to step 4
and start REM measurement. Press [STOP] to stop the measurement.
68
13.COORDINATE MEASUREMENT
By performing coordinate measurements it is possible to find the 3-dimensional coordinates of the
target based on station point coordinates, instrument height, target height, and azimuth angles of the
backsight station which are entered in advance.
13.1 Entering Instrument Station Data
Before performing coordinate measurement, enter instrument station coordinates and instrument
height.
$
• "Occupy" on the software represents instrument station.
PROCEDURE
1. First measure the instrument height with a tape

measure, etc.
2. Select "Coord." in <Menu>.
69
13. COORDINATE MEASUREMENT
3. Select "Occupy setup" and enter instrument

station coordinates,instrument height (HI) and
target height (HR).
4. Press [OK] to set the input values. <Set H angle>

is displayed again.
13.2 Azimuth Angle Setting
Based on the instrument station coordinates and backsight station coordinates which have already
been set, the azimuth angle of the backsight station is calculated.
70
PROCEDURE Entering coordinates
1. Select "Backsight setup" in <Coordinate>. <Set H

angle> is displayed.
• <Set H angle> can also be displayed from the

screen in step 4 of "13.1 Entering Instrument
Station Data".
2. Select the "Key in coord" tab and enter the

backsight station coordinates.
• [SRCH]: Performs Auto Pointing. Rotates the

instrument in the direction of the backsight.
• [Azimuth] /[H.ANG]/[None]/[0 SET] (in the
second page): Switches horizontal angle setting
method.
C "&Horizontal angle settings"
• Sight the backsight station and press [MEAS].

Press [STOP] to display the distance calculated
from coordinates, the measured distance, and
the difference between the two. Press [YES] to
set the azimuth angle and display <Coord.
measurement>.
3. Press [OK] to set the azimuth angle. <Coord.

measurement> is displayed.
71
PROCEDURE Entering angle


Station Data".
2. Select the "Key in angle" tab and enter the

desired angle in "H.ang".

3. Press [OK] to set the input values. <Coord.

PROCEDURE Entering azimuth


Station Data".
2. Select the "Key in azimuth" tab and enter the

desired angle in "Azimuth".

• [Azimuth] /[H.ANG]/[None]/[0 SET] (in the
second page): Switches horizontal angle setting
method.
C "&Horizontal angle settings"
3. Press [OK] to set the input values. <Coord.

72
& Horizontal angle settings

Azimuth (set both horizontal and azimuth angles to the same value)/H.ang (input both horizontal
and azimuth angles)/None (input azimuth angle only)/0 SET (horizontal angle set to 0°)
13.3 3-D Coordinate Measurement
The coordinate values of the target can be found by measuring the target based on the settings of the
instrument station and backsight station.
The coordinate values of the target are calculated using the following formulae.
N1 Coordinate = N0 + S x sinZ x cosAz
E1 Coordinate = E0 + S x sinZ x sinAz
Z1 Coordinate = Z0 + S x cosZ + ih - th
N0: Station point N coordinate S: Slope distance ih: Instrument height

E0: Station point E coordinate Z: Zenith angle th: Target height
Z0: Station point Z coordinate Az: Direction angle
"Null" coordinates will not be included in calculations. "Null" is not the same as zero.
PROCEDURE
1. Sight the target at the target point.
73
2. Select "Coord." in <Coordinate>.
Press [MEAS] to start measurement. Press

[STOP] to stop the measurement. The
coordinates of the target point are displayed.
Select the "Graphic" tab to display coordinates on
a graph.
3. Sight the next target and press [MEAS] to begin

measurement. Continue until all targets have
been measured.
4. When coordinate measurement is completed,

press {ESC} or tap the cross in the top-right
corner to return to <Coordinate>.
74
14.RESECTION MEASUREMENT
Resection is used to determine the coordinates of an instrument station by performing multiple
measurements of points whose coordinate values are known. Registered coordinate data can be
recalled and set as known point data. Residual of each point can be checked, if necessary.
Entry Output
Coordinates of : (Ni, Ei, Zi) Station point coordinates : (N0,E0, Z0)
known point
Observed : Hi
horizontal angle
Observed vertical : Vi
angle
Observed : Di
distance
• Between 2 and 10 known points can be measured by distance measurement, and between 3 and
10 known points by angle measurement.
• The more known points there are and the more points there are whose distance can be measured,
the higher the precision of the coordinate value calculation.
75
14. RESECTION MEASUREMENT
14.1 Coordinate Resection Measurement
N, E, Z of an instrument station is determined by the measurement.
PROCEDURE
1. Select "Resection" in <Menu>.
2. Select "NEZ" to display <Resection/Known

point>.
3. Input the known point.

After setting the coordinates and target height for
the first known point press [NEXT] to move to the
second point.
• Press [PREV] to return to settings for the

previous point.
When all required known points have been set,

press [OK].
76
4. Sight the first known point and press [MEAS] to

begin measurement.
The measurement results are displayed on the
screen.
• When [ANGLE] has been selected, the distance

cannot be displayed.
5. Press [YES] to use the measurement results of

the first known point.
• You can also input target height here.

• Press [NO] to return to the screen in step 4 and
perform measurement again.
6. Repeat procedures 4 to 5 in the same way from

subsequent points.
When the minimum quantity of observation data
required for the calculation is present, [CALC] is
displayed.
77
7. Press [CALC] or [YES] to automatically start

calculations after observations of all known points
are completed.
• Instrument station coordinates, station elevation,

and standard deviation, which describes the
measurement accuracy, are displayed.
Standard deviation for the northing, easting and

elevation coordinates of each point are displayed
in the "Detail" tab.
8. If there are problems with the results of a point,

align the cursor with that point and press [OMIT].
“OMIT” is displayed to the right of the point.
Repeat for all results that include problems.
2nd
9. Press [RE_CALC] to perform calculation again

without the point designated in step 8. The result
is displayed.
If there are no problems with the result, go to step
10.
If problems with the result occur again, perform
the resection measurement from step 4.
• Press [RE OBS] to measure the point

designated in step 8.
If no points are designated in step 8, all the
points or only the final point can be observed
again.
78
• Press [ADD] in the second page when there is a

known point that has not been observed or when
a new known point is added.
10. Press [OK] in <Resection/result> to display

<Resection/Set h angle>.
11. Select an angle mode and press [YES] to set the

azimuth angle of the first known point as the
backsight point and return to <Resection/Menu>.
12. Press [NO] to return to <Resection/Menu>

without setting the azimuth angle.
& Horizontal angle settings

H (set horizontal angle to measured value)/H=Az (set horizontal angle to the same value as
azimuth angle)/Az (set azimuth angle only)
$
• It is also possible to perform resection measurement by pressing [RESEC] in the third page of
Observation mode.
79
14.2 Height Resection Measurement
Only Z (height) of an instrument station is determined by the measurement.
• Known points must be measured by distance measurement only.

• Between 1 and 10 known points can be measured.
PROCEDURE
1. Select "Resection" in <Menu>.
2. Select "Elevation" to display <Resection/Known

point>.
3. Input the known point.

After setting the elevation and target height for the
first known point press [NEXT] to move to the
second point.
• Press [PREV] to return to settings for the

previous point.
When all required known points have been set,

press [OK].
80
4. Sight the first known point and press [MEAS] to

begin measurement.
The measurement results are displayed on the
screen.
5. If measuring two or more known points, repeat

procedures 4 in the same way from the second
point.
6. Press [CALC] or [YES] to automatically start

calculations after observations of all known points
are completed.
• Instrument station elevation and standard
deviation, which describes the measurement
accuracy, are displayed in the "Result" tab.
Standard deviation values for each point are

displayed in the "Detail" tab.
81
7. If there are problems with the results of a point,

align the cursor with that point and press [OMIT].
“OMIT” is displayed to the right of the point.
Repeat for all results that include problems.
8. Press [RE CALC] to perform calculation again

without the point designated in step 7 The result
is displayed.
If there are no problems with the result, go to step
9.
If problems with the result occur again, perform
the resection measurement from step 4.
• Press [RE_OBS] to measure the point

designated in step 7.
• Press [ADD] in the second page when there is a
known point that has not been observed or when
a new known point is added.
If no points are designated in step 7, all the points

or only the final point can be observed again.
9. Press [OK] to finish resection measurement and

return to <Resection/Menu>. Only Z (elevation) of
the instrument station coordinate is set. N and E
values are not overwritten.
82
& Resection calculation process

The NE coordinates are found using angle and distance observation equations, and the
instrument station coordinates are found using the method of least squares. The Z coordinate is
found by treating the average value as the instrument station coordinates.
Calculated instrument
station coordinates set
as hypothetical coordinates
83
& Precaution when performing resection

In some cases it is impossible to calculate the coordinates of an unknown point (instrument
station) if the unknown point and three or more known points are arranged on the edge of a
single circle.
An arrangement such as that shown below is desirable.
: Unknown point
: Known point
It is sometimes impossible to perform a correct calculation in a case such as the one below.
When they are on the edge of a single circle, take one of the following measures.
(1) Move the instrument station as close as possible

to the center of the triangle.
(2) Observe one more known point which is not on the

circle.
(3) Perform a distance measurement on at least one

of the three points.
G
• In some cases it is impossible to calculate the coordinates of the instrument station if the
included angle between the known points is too small. It is difficult to imagine that the longer
the distance between the instrument station and the known points, the narrower the included
angle between the known points. Be careful because the points can easily be aligned on the
edge of a single circle.
84
15.SETTING-OUT MEASUREMENT
Setting-out measurement is used to set out the required point.
The difference between the previously input data to the instrument (the setting-out data) and the
measured value can be displayed by measuring the horizontal angle, distance or coordinates of the
sighted point.
The horizontal angle difference distance difference, and coordinate difference are calculated and
displayed using the following formulae.
Horizontal difference
Displayed value (angle) = Horizontal angle of setting-out data - measured horizontal angle
Displayed value (distance) = measured horizontal distance x tan (horizontal angle of setting out data
- measured horizontal angle)
Slope distance difference

Displayed value (slope distance) * = measured slope distance - slope distance setting-out data
* Horizontal distance or height difference can be input in the above formula.
Coordinate difference
Displayed value (coordinates)* measured N setting-out coordinates - N coordinates of setting-out data
* E or Z coordinates can be input in the above formula
Height difference (REM setting out measurement)

Displayed value (height) = measured REM data - REM data of setting out data
• Setting out data can be input in various modes: slope distance, horizontal distance, height
difference, coordinates and REM measurement.
• It is possible to allocate softkeys in the Setting-out measurement menu to suit various applications
and the ways that different operators handle the instrument.
C "19.6 Allocating Key Functions"
15.1 Using the Guide Light in Setting-out Measurement
When the guide light is set to ON, the flashing speed of the light indicates the status of the instrument
and can be known when the user is located at a distance from the instrument. Also, the flashing colors
relative to the target indicate the direction of the instrument and allow the user to reposition the target.
CTurning the Guide light ON/OFF: "5.1 Basic Key Operation"
• The pattern of the guide light can be changed.

85
15. SETTING-OUT MEASUREMENT
I Guide light status and meaning

Status of instrument

simultaneously)
Searching in progress
Fast flashing (Red and green
Measuring (continuous measurement)
simultaneously)
Distance measurement error (no signal, sighting error)
Green and red alternate flashing Search error (error screen only)
Indication for positioning target during setting-out measurement

Increased flashing speed (From position of poleman) Move target toward instrument
Decreased flashing speed (From position of poleman) Move target away from
instrument
Fast flashing Target is at correct distance
Red (From position of poleman) Move target left
Green (From position of poleman) Move target right
Red and Green Target is at correct horizontal position
15.2 Distance Setting-out Measurement
The point is to be found based on the horizontal angle from the reference direction and the distance
from the instrument station.
86
PROCEDURE
1. Select "Setting out" in <Menu> to display <Setting

out>.
2. Select "Occupy setup" to display <Occupy

setup>. Enter data for the instrument station and
press [OK] to move to Backsight setup.
C"13.1 Entering Instrument Station Data"
3. Set the azimuth angle for the backsight station.

Press [OK] to return to <Setting out>.
87
4. Select "SO data setting" In <Setting out> to

display <SO data setting>. In the distance mode
that conforms to your measurement
requirements, enter the included angle between
the reference point and the setting-out point in
"SO.H.ang", and the distance (slope distance,
horizontal distance or height difference) from the
instrument station to the position to be set out in
"SO.Sdist".
• Each time [Shvr] is pressed, the distance mode

changes from "SD" (slope distance), "HD"
(horizontal distance), "VD" (height difference),
and "Ht." (REM).
• Press [COORD] in the second page and input
coordinates in <Key in coord>. The angle and
distance from these coordinates to the position
to be set out will be calculated.
5. Enter values and press [OK] to display the screen

at right.
Press [H.TURN] to automatically rotate the
instrument until the difference in horizontal angle
to the setting out point reads 0°.
88
• Press [CNFG] in the second page to set setting

out accuracy. When the position of the target is
within this range both arrows will be displayed to
indicate that the target position is correct.
6. Position the target on the line of sight and press Arrows indicate direction to move
[MEAS] to begin distance measurement.
The distance and direction to move the target until
the setting out point is located is displayed on the
instrument. The sighting point measurement
results (currently installed position of the target)
are displayed.
• Movement indicator (Red indicates that target

position is correct)
Y : (Viewed from instrument) Move target to
the left
Z : (Viewed from instrument) Move target to
the right
YZ : Target position is correct
G : (Viewed from instrument) Move target
closer
O : (Viewed from instrument) Move target
away
OG : (Viewed from instrument) Target position
is correct
Q : Move target upward
H : Move target downward
QH : Target position is correct
• Each time [Shvr] is pressed, the distance mode

changes from "SD" (slope distance), "HD"
(horizontal distance), "VD" (height difference),
and "Ht." (REM).
• Press [CNFG] in the second page to set setting
out accuracy. When the position of the target is
within this range both arrows will be displayed to
indicate that the target position is correct.
89
7. Move the target until the distance to the setting-

out point reads 0m. When the target is moved
within the allowed range, all distance and position
arrows are displayed.
8. Press {ESC} to return to <Setting out>. Set the

next setting out point to continue setting out
measurement.
15.3 Coordinates Setting-out Measurement
After setting the coordinates for the point to be set out, the instrument calculates the setting-out
horizontal angle and horizontal distance. By selecting the horizontal angle and then the horizontal
distance setting-out functions, the required coordinate location can be set out.
• Previously recorded setting-out points can be placed in order. Up to 50 points can be recorded.
• To find the Z coordinate, attach the target to a pole etc. with the same target height.
90
PROCEDURE
1. Select "Setting out" in <Menu> to display <Setting

out>.

setup>. If necessary, enter data for Backsight
setup.
C"15.2 Distance Setting-out Measurement"
steps 2 to 3
3. Select "Key in coord" in <Setting out>. Record all

the setting-out points (includes setting-out points
you will measure from now).
Press [ADD] to record new data.
• Press [DEL] in the second page to delete the

selected setting out point.
• Press [DELALL] in the second page to delete all
setting out points.
4. Select a setting-out point in the first screen of step

3 and press [OK] to display <Set out Coords>.
91
5. Position the target on the line of sight and press

instrument until the angle of the setting out point
reads 0°.
[MEAS] to begin distance measurement.
The distance and direction to move the target until
the setting out point is located is displayed on the
instrument. The sighting point measurement
results (currently installed position of the target)
are displayed.
• Switch between the tabs to display different sets

Height difference direction
of information. Position of poleman
The Graph 1 tab shows the current position of
the mirror and the direction to the setting out
point from this position.
The Graph 2 tab shows the position of the setting
out point (square) and the current location of the
mirror (circle).
92
Move the target to find the correct distance (0 is

displayed) to the setting out point.
CMovement indicators: "15.2 Distance Setting-
out Measurement" step 6
6. Press [OK] to return to <Key in coord>. Set the

next setting out point to continue setting out
measurement.
93
15.4 REM Setting-out Measurement
To find a point where a target cannot be directly installed, perform REM setting-out measurement.
C"12.5 REM Measurement"
PROCEDURE
1. Install a target directly below or directly above the

point to be found. Then use a measuring tape etc.
to measure the target height (height from the
survey point to the target).
2. Select "Occupy setup" in <Setting out> to display

<Occupy setup>. If necessary, enter data for
Backsight setup.
C"15.2 Distance Setting-out Measurement"
steps 2 to 3
3. Select "SO data setting" In <Setting out> to

display <SO data setting>. Press [Shvr] until the
distance input mode is "SO.Height.". Input height
from the surveying point to the position to be set
out in "SO.Height". If necessary, input the angle to
the point to be set out.
4. Enter values and press [OK] in step 3 to display

the screen at right.
instrument until the angle of the setting out point
reads 0°.
94
5. Sight the target and press [MEAS]. Measurement

begins and the measurement results are
displayed.
6. Press [REM] to start REM measurement. Arrows indicate direction to move

The distance (height difference) and direction to
move the target until the sighting point and setting
out point are located is displayed on the
instrument.
Press [STOP] to stop measuring.
Find the setting-out point by moving the telescope

until the distance to the setting-out point reads 0m.
• Movement indicator (Red indicates that target

position is correct)
Q : Move the telescope near the zenith

H : Move the telescope near the nadir
HQ : Telescope direction is correct
CFor details of other movement indicators:
"15.2 Distance Setting-out Measurement"
step 6
• Press [CNFG] to set setting out accuracy. When

the position of the target is within this range both
arrows will be displayed to indicate that the
target position is correct.
7. Press {ESC} to return to <SO data setting>.
95
16.OFFSET MEASUREMENT
Offset measurements are performed in order to find a point where a target cannot be installed directly
or to find the distance and angle to a point which cannot be sighted.
• It is possible to find the distance and angle to a point you wish to measure (target point) by installing
the target at a location (offset point) a little distance from the target point and measuring the distance
and angle from the survey point to the offset point.
• The target point can be found in the three ways explained in this chapter.
• The instrument station and backsight must be set before the coordinates of an offset point can be
found. Station and backsight setup can be performed in the Offset menu.
C Occupy setup: "13.1 Entering Instrument Station Data", Backsight setup: "13.2 Azimuth Angle
Setting".
16.1 Offset Single-distance Measurement
Finding it by entering the horizontal distance from the target point to the offset point.
• When the offset point is positioned to the left or right of the target point, make sure the angle formed
by lines connecting the offset point to the target point and to the instrument station is almost 90°.
• When the offset point is positioned in front of or behind the target point, install the offset point on a
line linking the instrument station with the target point.
PROCEDURE
1. Set the offset point close to the target point and

measure the distance between them, then set up
a prism on the offset point.
96
16. OFFSET MEASUREMENT
2. Select "Offset" in <Menu> to display <Offset>.

setup>. Enter data for the instrument station and
press [OK] to move to Backsight setup.
C"13.1 Entering Instrument Station Data"
4. Set the azimuth angle for the backsight station.

Press [OK] to return to <Offset>.
5. Select “OffsetDIST”.
Input the following items.
(1) Direction of the offset point.
(2) Horizontal distance from the target point to
the offset point.
• Direction of offset point

← : On the left of the target point.
→ : On the right of the target point.
↓ : Closer than the target point.
↑ : Beyond the target point.
97
6. Sight the offset point and press [MEAS] in the

Results for target point
screen of step 3 to start measurement.
The measurement results are displayed.
• Press [HVD/nez] to switch results for the

target point between distance/angle values
and coordinate/elevation values.
Results for offset point
16.2 Offset Angle Measurement
Sighting the direction of the target point to find it from the included angle.
Install offset points for the target point on the right and left sides of and as close as possible to the
target point and measure the distance to the offset points and the horizontal angle of the target point.
PROCEDURE
1. Set the offset points close to the target point

(making sure the distance from the instrument
station to the target point and the height of the
offset points and the target point are the same),
then use the offset points as the target.
98
Select "OffsetANG.".
3. Sight the offset point and press [MEAS] to start

measurement.
4. Sight the target point and press [H.ANG]. Results for target point
• Press [HVD/nez] to switch results for the

target point between distance/angle values
and coordinate/elevation values.
5. Press [OK] in the screen in step 4 to return to

<Offset>.
99
16.3 Offset Two-distance Measurement
By measuring the distances between the target point and the two offset points.
Install two offset points (1st target and 2nd target) on a straight line from the target point, observe the
1st target and 2nd target, then enter the distance between the 2nd target and the target point to find
the target point.
• It is possible to make this measurement easily using the optional equipment: the 2-point target
(2RT500-K). When using this 2-point target, be sure to set prism constant correction value to 0.
C"24. OPPTIONAL ACCESSORIES"
How to use 2-point target (2RT500-K)
• Install the 2-point target with its tip at the target point.
• Face the targets toward the instrument.
• Measure the distance from the target point to the 2nd target.
• Set the prism constant correction value to 0mm.
$
• The target should be sighted manually when performing two-distance offset measurement.
Multiple prisms in the field will mean that Auto Pointing may not operate correctly, or the
instrument may not be able to judge which is the desired target.
100
PROCEDURE
1. Install two offset points (1st target, 2nd target) on

a straight line from the target point and use the
offset points as the target.
Select "5.Offset2D".
3. Press [CNFG] and input the distance from the

2nd target to the target point in "Offset dist.". Set
reflector settings and press [OK] to confirm.
• Press [LIST] to edit the prism constant

correction value and aperture in <Reflector
setting>.
4. Sight the 1st target and press [MEAS] to start

measurement.
Press [STOP] to stop the measurement. The
measurement results are displayed. Press [YES]
to confirm.
101
5. Sight the 2nd target and press [MEAS] to start

measurement.
Press [STOP] to stop the measurement. The
measurement results are displayed.
6. Press [YES] to display results for the target point.
Press [HVD/nez] to switch results for the target

point between distance/angle values and
coordinate/elevation values.
102
17.MISSING LINE MEASUREMENT
Missing line measurement is used to measure the slope distance, horizontal distance, and horizontal
angle to a target from the target which is the reference (starting point) without moving the instrument.
• It is possible to change the last measured point to the next starting position.
• Measurement results can be displayed as the gradient between two points.
17.1 Measuring the Distance between 2 or more Points
PROCEDURE
1. Select "MLM" in <Menu>.
103
17. MISSING LINE MEASUREMENT
2. Sight the starting position, and press [MEAS] to

start measurement.
Press [STOP] to stop measurement.
$
• When measurement data already exists the
screen of step 3 is displayed and measurement
starts.
3. Sight the next target and press [MLM] to Results for measurement between starting
begin observation. Slope distance, grade, position and second target
horizontal distance and height difference
between multiple points and the starting
position can be measured this way.
• Press [MEAS] to re-observe the starting

position. Sight the starting position and
press [MEAS].
• When [MOVE] is pressed, the last target
measured becomes the new starting
position to perform missing line
measurement of the next target.
C"17.2 Changing the Starting Point"
Results for current point
4. Press {ESC} or tap the cross in the top-right

corner to end missing line measurement.
104
17.2 Changing the Starting Point
It is possible to change the last measured point to the next starting position.
PROCEDURE
1. Observe the starting position and target following

steps 1 to 3 in "17.1 Measuring the Distance
between 2 or more Points".
2. After measuring the targets, press [MOVE].
105
Press [YES] in the confirmation message window.
• Press [NO] to cancel measurement.
3. The last target measured is changed to the new

starting position.
4. Perform missing line measurement following

steps 3 to 4 in "17.1 Measuring the Distance
between 2 or more Points".
106
18.SURFACE AREA CALCULATION
You can calculate the area of land (slope area and horizontal area) enclosed by three or more known
points on a line by inputting the coordinates of the points
Input Output
Coordinates: P1 (N1, E1, Z1) Surface area: S (horizontal area and slope
area)
...
P5 (N5, E5, Z5)
• Number of specified coordinate points: 3 or more, 30 or less

• Surface area is calculated by observing in order the points on a line enclosing an area.
G
• An error will occur if only two points (or less) are entered when specifying an enclosed area.
• Be sure to observe points on an enclosed area in a clockwise or counterclockwise direction. For
example, the area specified by entering point numbers 1, 2, 3, 4, 5 or 5, 4, 3, 2, 1 implies the same
shape. However, if points are not entered in numerical order, the surface area will not be calculated
correctly.
& Slope area

The first three points specified (measured) are used to create the surface of the slope area.
Subsequent points are projected vertically onto this surface and the slope area calculated.
107
18. SURFACE AREA CALCULATION
PROCEDURE Surface area calculation by measuring points
1. Select "Area calc." in <Menu>
2. Press [OBS] to display <Area calculation/

measurement>. Sight the first point on the line
enclosing the area, and press [MEAS].
Measurement begins and the measured values
are displayed. Press [STOP] to stop measuring.
108
3. The measurement results are displayed. Press

[YES] to confirm.The value of point 1 is set in
"Pt_01".
4. Repeat steps 2 to 3 until all points have been

measured. Points on an enclosed area are
observed in a clockwise or counterclockwise
direction.
For example, the area specified by entering point
numbers 1, 2, 3, 4, 5 or 5, 4, 3, 2, 1 implies the
same shape.
109
5. Press [CALC] to display the calculated area.
6. Press [OK] to return to <Area/key in coord.>.

Press {ESC} or tap the cross in the top-right
corner to quit area calculation.
110
19.CHANGING THE SETTINGS
This section explains the contents of parameter settings in Basic mode and how to change these
settings.
Each item can be changed to meet your measurement requirements.
<Configuration> can be accessed by pressing the "CONFIG" icon in <Top>.
The following chapters provide details of items in Configuration mode.

• Communication settings C"9. CONNECTING TO EXTERNAL DEVICES"
• Motor settings C"10.1 Auto Pointing Settings"
• Instrument configurations C"21.2 Tilt Sensor", "21.3 Collimation", "21.5 Image Sensor Reticle"
19.1 Observation Conditions
111
19. CHANGING THE SETTINGS

Distance mode : Sdist (slope distance)*, Hdist (horizontal distance),
V.dist (height difference)
Hdist & : Ground*, Grid
Tilt crn (tilt correction) & : Yes (H,V)*, No, Yes (V)
Tilt error : No action*/Go to <Tilt> (electric circular level is
displayed)
Coll.crn. (collimation correction) & : No, Yes*
C&R crn. : No, Yes(K=0.142),Yes(K=0.20)*
V manual : No*, Yes
V.obs (vertical angle display method) & : Zenith*, Horiz., Horiz ±90
Coordinates : N-E-Z*, E-N-Z
Sea level crn. (Sea level correction) & : Yes, No*
Ang.reso. (Angle resolution) : DS-101AC/102AC: 0.5", 1"*
DS-103AC/105AC: 1"*, 5"
Dist.reso. (Distance resolution) : DS-101AC/102AC: 0.1mm, 1mm*
DS-103AC/105AC: 1mm*
ppm setting : Press, Temp.*, +Humidity
CSetting "V manual" to "Yes": "26.2 Manually Indexing the Vertical Circle by Face Left, Face Right
Measurement"
& Hdist
The instrument calculates horizontal distance using slope distance values. Horizontal distance
display can be selected from the following methods.
Ground: Distance without sea level correction
Grid: Distance on the rectangular coordinates system calculated by sea level correction
(When "Sea level crn." is set to "No", Distance on the rectangular coordinates
system without correction)
Slope distance
Ground
Projection
distance
Plane rectangular
coordinates system
Grid
Mean sea level
112
& Automatic tilt angle compensation mechanism

The vertical and horizontal angles are automatically compensated for small tilt errors using the
2-axis tilt sensor.
• Read the automatically compensated angles when the display has stabilized.
• The horizontal angle error (vertical axis error) fluctuates according to the vertical axis, so when
the instrument is not completely leveled, changing the vertical angle by rotating the telescope
will cause the displayed horizontal angle value to change.
• Compensated horizontal angle = Measured horizontal angle + Tilt in angle/tan (Vertical angle)
• When the telescope is directed close to the zenith or nadir angle, tilt compensation is not
applied to the horizontal angle.
& Collimation correction

The instrument has a collimation correction function that automatically corrects horizontal angle
errors caused by horizontal axis and leveling axis errors.
& V mode (vertical angle display method)

Zenith Horiz Horiz 90°
& Sea level correction

The instrument calculates horizontal distance using slope distance values. As this horizontal
distance does not take height above sea level into consideration, performing spherical correction
is recommended when measuring at high altitudes. Spherical distance is calculated as follows.
Spherical distance
R – Ha
= ------------------ × d 1
R
Where: R = radius of the spheroid (6372.000m)

Ha = averaged elevation of the instrument point and target point
d1 = horizontal distance
113
19.2 Instrument Configuration

Power off & : No/5min./10min./15min./30min.*
Power off (Remote)& : No*/5min./10min./15min./30min.
Backlight (Reticle On) & : 0 to 8 (1*) (Brightness level on pressing {J})
Backlight (Normal) & : 0 to 8 / Auto (Auto*)
Backlight Off & : No*/30sec/1min./5min./10min.
Key backlight & : Off/On*
Reticle lev & : 0 to 5 level (3*)
EDM ALC & : Free*/Hold
Guide pattern : 1* (simultaneous)/2 (alternating)
Laser-pointer off & : No/1min./5min.*/10min./30min.
Beep : On*/Off
Remote PWR-On : Yes/No*
Color & : 1/2 (monochrome) / Auto (Auto*)
Touch panel : On (fixed)
$
• Press [PNL CAL] to display the touch panel calibration screen.
C"8.1 Configuring the Touch Panel"
114
& Adjusting backlight brightness/turning the reticle illumination and key backlight ON/OFF
Pressing {J} switches the brightness level of the backlight in conjunction with the ON/OFF
status of the reticle illumination/key backlight.
When the instrument is powered ON the brightness level is set to "Backlight (Normal)".
"Backlight (Normal)" was set to a higher brightness level than "Backlight (Reticle ON)" when the
instrument was shipped but these values can be modified according to user preferences.
Power ON
Backlight (Normal) Time set in

brightness "Backlight Off" elapses
{J} {J}
Reticle backlight OFF Reticle backlight ON
Backlight
(Reticle ON)
brightness
Key backlight ON
Only when "Key
backlight" set to "ON"
Key pressed
Touch panel operated Backlight OFF
$
• When "Backlight (Normal)" is set to "Auto" the instrument light sensor gauges the level of
ambient brightness and automatically sets backlight brightness accordingly. Depending on
ambient light conditions, performance of this function may be sub-optimal, or the display may
flicker between brightness settings.
& Power-saving automatic cut-off/Backlight Off

To save power, power to the instrument is automatically cut off if it is not operated for the set
time.
The backlight will similarly be turned off if the instrument is not operated for the selected time.
However, the backlight will not be turned off when "Backlight" is set to "ON".
& Power-saving automatic cut-off (Power on command)

When turned on using a Power on command, power to the instrument is automatically cut off if
it is not operated for the set time.
115
& Key backlight

The key backlight can be set to "ON" or "OFF". When "ON" the keys will be illuminated when
"Backlight (Bright)" is active.
& EDM ALC

Set the light receiving status of the EDM. While carrying out continuous measurement, set this
item according to the measurement conditions.
• When EDM ALC is set to "Free," the instrument’s ALC will be automatically adjusted if an error
occurs as a result of the amount of light received. Set to "Free" when the target is moved during
measurement or different targets are used.
• When "Hold" is set, the amount of light received will not be adjusted until continuous
measurement is completed.
• If an obstacle intermittently obstructs the light beam during continuous measurement and the
"Signal off" error occurs, each time the obstruction occurs it takes some time for the amount of
light received to be adjusted and the measurement value displayed. Set to "Hold" when the light
beam used for measurement is stable but is frequently obstructed by obstacles such as people,
cars, or tree branches etc. preventing measurement from being performed.
$
• When the distance measurement mode is set to "Tracking" (target is moved during distance
measurement) the EDM ALC will be adjusted regardless of the EDM ALC setting.
& Laser-pointer off

To save power, the laser-pointer is automatically turned off after the set time has elapsed.
& Color setting

Set "Color" to "2" (monochrome) when strong sunlight reduces visibility of the display. When
"Auto" is selected, the instrument detects the ambient brightness level and automatically sets
the appropriate color setting accordingly. C"5.2 Display Functions"
G
• Do not block the instrument light sensor when "Color" is set to "Auto". The instrument will be
unable to gauge ambient brightness and the display will flicker as a result.
19.3 EDM Settings
I "EDM" tab
116
Items set, options, and input range (*: Factory setting)

Dist. mode (Distance measurement mode): Fine “R”*, Fine AVG n= 1(Setting: 1 to 9 times), Fine
“S”, Rapid "R", Rapid “S”, Tracking
Reflector : Prism*/360° Prism/Sheet/N-Prism
Prism constant value : -99 to 99 mm ("Prism" is selected: 0*, "360° Prism" is
selected: -7, "Sheet" is selected: 0)
Aperture : 1 to 999mm ("Prism" is selected: 58*, "360° Prism" is
selected: 34, "Sheet" is selected: 50)
Illum. hold ({J} function) : Laser-pointer*/Guide light
Guide light (Bright) : 1 to 3 (3*)
• The setting for "Fine AVG" distance measurement mode can be increased/decreased using the
[ + ]/[ - ] softkeys.
• Target information can be edited and recorded.
C"PROCEDURE Recording and editing target information"
• "Prism const." and "Aperture" will not be displayed when "N-Prism" is selected in "Reflector".
• Recommended values of "Aperture" are: 58 for Prism-2, 32 for Prism-5, 34 for ATP1/ATP1S and
actual size for reflective sheets.
• When "prism const." (prism constant values) are changed and [OK] is pressed, these changes
are reflected in the status bar/Starkey mode target type display temporarily. This display will also
change to reflect changes in target information settings made using a data collector temporarily.
In both of the above cases, changes will not be recorded in <Reflector setting>.
CStatus bar: "5.2 Display Functions", Starkey mode: "5.4 Starkey Mode",<Reflector setting>:
"PROCEDURE Recording and editing target information", Cold boot: "8.2 Resolving
Software Issues & Cold boot"
• The Guide light brightness item ("Guide light (Bright)") will be displayed only when "Illum. hold"
is set to "Guide light".
& prism constant correction value

Reflective prisms each have their prism constant.
Set the prism constant correction value of the reflective prism you are using. When selecting "N-
Prism" in "Reflector", prism constant correction value is set to "0" automatically.
I "ppm" tab
• [0ppm]: Atmospheric correction factor returns to 0 and temperature and air pressure are set to
the factory settings.
117
• Atmospheric correction factor is calculated and set using the entered values of the temperature
and air pressure. Atmospheric correction factor can also be entered directly.
• When the settings here are different between basic mode and program mode, program mode
settings are prior for use.
Items set, options, and input range (*: Factory setting)

Temperature : -30 to 60°C (15*), -22 to +140°F (59*)
Pressure : 500 to 1400hPa (1013*), 375 to 1050mmHg (760*),
14.8 to 41.3 (inchHg) (29.9*)
Humidity : 0 to 100% (50*)
ppm (Atmospheric correction factor) : -499 to 499 (0*)
• The "Humidity" item is displayed only when the "ppm setting" in "Obs. condition" is set to
"+Humidity".
• When 0.1mm is selected in "Dist.reso", values can be input to the first decimal place.
& Atmospheric correction factor

The velocity of the light beam used for measurement varies according atmospheric conditions
such as temperature and air pressure. Set the atmospheric correction factor when you wish to
take this influence into account when measuring.
• The instrument is designed so that the correction factor is 0 ppm at an air pressure of 1013
hPa, a temperature of 15°C, and a humidity of 50%.
• By inputting the temperature, air pressure values and humidity, the atmospheric correction
value is calculated using the following formula and set into the memory.
Atmospheric Correction Factor (ppm) =
0.294362 × p 0.04127 × e
282.324 – ------------------------------------------ + ------------------------------------------
1 + 0.003661 × t 1 + 0.003661 × t
t: Air temperature (°C)
p: Pressure (hPa)
e: Water vapor pressure (hPa)
h: Relative humidity (%)
E : Saturated water vapor pressure
• e (water vapor pressure) can be calculated using the following formula.

E
e = h × ----------
100 ( 7.5 × t )
----------------------------
( t + 237.3 )
E = 6.11 × 10
• The instrument measures the distance with a beam of light, but the velocity of this light varies
according to the index of refraction of light in the atmosphere. This index of refraction varies
according to the temperature and pressure. Near normal temperature and pressure
conditions:
With constant pressure, a temperature change of 1°C: an index change of 1 ppm.
With constant temperature, a pressure change of 3.6 hPa: an index change of 1 ppm.
To perform high accuracy measurements, it is necessary to find the atmospheric correction
factor from even more accurate temperature and pressure measurements and perform an
atmospheric correction.
118
It is recommended that extremely precise instruments be used to monitor the air temperature
and pressure.
• Enter the average temperature, air pressure and humidity along the measurement beam route
in "Temperature", "Pressure" and "Humidity".
Flat terrain:Use the temperature, pressure and humidity at the midpoint of the line.
Mountainous terrain:Use the temperature, pressure and humidity at the intermediate point (C).
If it is not possible to measure the temperature, pressure and humidity at the midpoint, take such
measurements at the instrument station (A) and the target station (B), then calculate the average
value.
Average air temperature : (t1 + t2)/2
Average air pressure : (p1 + p2)/2
Average humidity : (h1 + h2)/2
Humidity h1
Humidity h2
• If the weather correction is not required, set the ppm value to 0.
PROCEDURE Recording and editing target information
The [LIST] softkey is displayed when either "Reflector" or "Prism const." is selected in the "EDM" tab
of <EDM configurations>.
119
1. Press [LIST] to display a list of all recorded

targets.
• [ADD]: Displays <Reflector list>. Select the

desired target from this list and press [OK] to
register in the list in <Reflector setting>. Up to a
maximum of 6 targets can be recorded.
• [DEL]: Deletes the selected target.
2. To edit a target, select the desired target and

press [EDIT]. <Reflector/edit> is displayed.
Select/input relevant information for the target.
Reflector : Prism/Sheet/N-Prism/360° Prism

Const. : -99 to 99 mm
Aperture : 1 to 999 mm
• When selecting "N-Prism" in "Reflector", prism

constant correction values and aperture are set
to "0" automatically.
3. Press [OK] in the screen of step 2 to save edited

information and return to <Reflector setting>.
Press [OK] to return to <EDM configurations>.
19.4 Allocating User-defined Tabs
It is possible to allocate tabs in Observation mode and Menu mode to suit the measurement
conditions. It is possible to operate the instrument efficiently because unique tab allocations can be
preset to suit various applications and the ways that different operators handle the instrument.
• The current tab allocations are retained until they are revised again, even when the power is cut off.
• Press [CLEAR] in <Customize/Select screen> to return all customized configurations including
screen controls, status bar settings, and softkey allocations to their previous settings.
• One screen can contain a maximum of 5 tabs.
G
• When tab allocations are recorded and registered, the previously recorded tab settings are cleared.
I Tab allocations
The following are tabs allocated when the instrument was shipped and tabs that can be defined
by the user.
120
• "Basic observation"
Factory settings User-definable tabs

SHV SHV
SHVdist SHVdist
Graphic SHV + Coord.
• Setting out
Obs. Obs.
Graphic
• Setting out Coord.

SHV SHV
NEZ NEZ
Graph1
Graph2
G
• Graphic tab cannot be deleted.
PROCEDURE Allocating tabs
1. Select "Customize" to display <Customize/Select

screen>.
Select the measurement mode in which you want
to allocate a tab.
121
Select "Tab page".
2. Use the softkeys ([ADD], [DEL] etc.) in

<Customize tab page> to allocate the desired tab
page layout.
• Press [ADD] to add the selected tab at the right-

hand side of the screen.
• Press [INS] in the second page to insert the
selected tab in front of the current tab.
• Press [CNFG] in the second page to replace the
current tab with the selected tab.
• Press [DEL] to delete the current tab.
G
• Tabs, once deleted, cannot be retrieved.
Select a tab type from the "Type" drop-down list.
3. Repeat step 2 to perform further tab allocations.
4. Press [OK] to finish allocating tabs. The allocated

tabs are stored in memory and <Customize> is
displayed. The newly allocated tabs appear in the
relevant measurement screen.
122
19.5 Customizing Screen Controls
It is possible to customize screen controls in Observation mode to suit the measurement conditions
and the different methods employed by different operators.
• The current screen control settings are retained until they are revised again, even when the power
is cut off.
• Press [CLEAR] in <Customize/Select screen> to return all customized configurations including tab
pages, status bar settings, and softkey allocations to their previous settings.
• Screen controls cannot be set for the "Graphic" tab.
G
• When screen control settings are recorded and registered, the previously recorded settings are
cleared.
PROCEDURE Customizing screen controls

screen>.
to customize screen controls.
Select "Control".
123
2. Press [ADD] to add a control drop-down list.

• Press [DEL] to delete the selected control.
G
• Controls, once deleted, cannot be retrieved.
3. Select a screen control from the list.
4. Press [CNFG] to set the size, thickness, color

and spacing of the font.
5. Repeat steps 2 to 4 to customize more screen

controls.
6. Press [OK] to finish customizing screen controls.

The modifications are stored in memory and
<Customize> is displayed.
The modifications are reflected in the relevant
screens.
124
19.6 Allocating Key Functions
It is possible to allocate the softkeys in Observation mode to suit the measurement conditions. It is
possible to operate the instrument efficiently because unique softkey allocations can be preset to suit
various applications and the ways that different operators handle the instrument.
• The current softkey allocations are retained until they are revised again, even when the instrument
is powered OFF.
pages, status bar/starkey mode settings, and screen controls to their previous settings.
G
• When softkey allocations are recorded and registered, the previously recorded key settings are
cleared.
• Softkeys cannot be allocated to "Graphic" tabs.
I Screens that can be customized and softkey allocations when shipped

1. "SHV" and "SHVdist" tabs of <Basic observation>
Page 1 [SRCH] [MOTOR] [0SET] [MEAS]
Page 2 [MENU] [EDM] [H-SET] [COORD]
Page 3 [OFFSET] [RESEC] [REM] [S-O]
2. "Obs." tab of <Setting out>

Page 1 [ --- ] [SHVR] [H.TURN] [MEAS]
Page 2 [CNFG] [ --- ] [ --- ][REM]
Page 3 [ --- ] [ --- ] [ --- ] [ --- ]
3. "SHV" and "NEZ" tabs of <Set out Coords>

Page 1 [OK] [CNFG][H.TURN] [MEAS]
Page 2 [ --- ] [ --- ] [ --- ] [ --- ]
Page 3 [ --- ] [ --- ] [ --- ] [ --- ]
I Functions that can be allocated to the softkeys

[ --- ] : No functions set
[MEAS] : Distance and angle measurement
[0SET] : Set horizontal angle to 0°
[H-SET] : Set required horizontal angle
[SHV] : Switch the "SHV" tab and "SHVdist" tab (can only be allocated to 1
above)
[R/L] : Select horizontal angle right/left. The capitalized letter in the softkey
indicates the currently selected mode.
[ZA / %] : Switch between zenith angle/slope in %. The capitalized letter in the
softkey indicates the currently selected mode.
[HOLD] : Hold horizontal angle/release horizontal angle
[CALL] : Display final measurement data
[HVOUT-S] : Output angle measurement results to an external device (SET format)
125
[HVDOUT-S] : Output distance and angle measurement results to an external device

(SET format)
[NEZOUT-S] : Output coordinates data to an external device (SET format)
[HVOUT-T] : Output angle measurement results to an external device (GTS format)
(can only be allocated to 1 above)
[HVDOUT-T] : Output distance and angle measurement results to an external device
(GTS format) (can only be allocated to 1 above)
[NEZOUT-T] : Output coordinates data to an external device (GTS format) (can only
be allocated to 1 above)
[F/M] : Switch distance units between meters/feet
[HT] : Set the instrument station, coordinates and instrument height
[S-LEV] : Return signal
[TILT] : Display tilt angle
[MOTOR] : Display <Motor>
[INV] : Rotates the instrument 180°
[SRCH] : Automatically sights the center of the target
[Fix Vel] : Fixed velocity rotation around vertical and horizontal axes
[EDM] : EDM settings
[MENU] : Display <Menu> (coordinate measurement, setting out measurement,
offset measurement, REM measurement, missing line measurement,
resection, area calculation)
[COORD] : Coordinates measurement
[S-O] : Setting-out measurement
[OFFSET] : Offset measurement
[A-OFS] : Angle offset menu
[D-OFS] : Distance offset menu
[2D-OFS] : Offset/2D menu
[MLM] : Missing line measurement
[REM] : REM measurement
[RESEC] : Resection measurement
[AREA] : Surface area measurement
[CNFG] : Set setting out accuracy (can only be allocated to 2 and 3 above)
[H.TURN] : Rotate the instrument to the entered horizontal angle. Rotate
horizontally to the angle for the setting out point when performing
setting out (can only be allocated to 2 and 3 above).
[SHVR] : Switch distance mode between slope distance (SD)/horizontal
distance (HD)/height difference (VD)/REM (R) in setting out screens.
The capitalized letter in the softkey indicates the currently selected
mode (can only be allocated to 2 above).
[OK] : Terminate setting out measurement for the selected setting out point
and return to <Key in coord>. This setting out point will be removed
from the list (can only be allocated to 3 above).
126
PROCEDURE Allocating a softkey

screen>.
to allocate a softkey.
Select "Softkey".
2. Select the desired tab. All softkeys currently

allocated to each page of that tab are displayed.
3. Select the softkey whose allocation you want to

change. Tapping a softkey, or pressing {SPACE}
when the cursor is aligned with a softkey, will
display <Softkey list>.
127
4. Select the desired softkey from <Softkey list> to

allocate to the position specified in step 3.
5. Repeat steps 3 to 4 to perform further key

allocations.
6. Press [OK] to finish allocating keys. The allocated

keys are stored in memory and <Customize> is
displayed. The newly allocated keys appear in the
relevant measurement screen.
19.7 Changing Starkey Mode Icons
It is possible to preset icon allocations of the Starkey mode to suit various applications and the ways
• The current icon allocations are retained until they are revised again, even when the power is turned
off.
pages, screen controls and softkey allocations to their previous settings.
G
• When icon allocations are recorded and registered, the previously recorded settings are cleared.
• When icon allocations are recorded and registered, the setting reflects to Status bar.
I Icons that can be allocated to the status bar

Remaining battery power
Target display
Motor
Laser-pointer/guide light
Tilt angle compensation
Communication status
Input mode
SIP (Input panel)
ppm (atmospheric correction factor)
Touch panel
Disk
No icon
128
PROCEDURE Changing icon allocations

screen>.
Select "Starkey".
2. Select the icon (in the Starkey mode) you wish to

re-allocate. Tap the icon to display <Starkey list>.
3. Select the new icon from <Starkey list>.

The icon is allocated in the selected icon position.
4. Repeat steps 2 to 3 to perform further icon

allocations.
5. Press {ENT} to finish allocating icons. The

allocated icons are stored in memory and
<Customize/Select screen> is restored. The
newly allocated icons appear in the Starkey
mode.
129
19.8 Units

Temperature : Celsius*/Fahrenheit
Pressure : hPa*/mmHg/InchHg
Angle : Degree (DDD.MMSS)*/Gon/Mil
Distance : Meter*/Feet/Inch
Feet (only displayed when "Feet" or "Inch" selected above):
International*/US
$
• OS rounds off the value input by the digit of less than 0.004 feet/0.017 inch.
& Inch (Fraction of an inch)

“Fraction of an inch” is the unit used in the United States and expressed like the following
example.
G
• Even if “inch” is selected in this setting, all the data including the result of area calculation are
output in “feet” and all the distance values must be input in “feet”. In addition, when the “inch”
display exceeds the range, it is displayed in “feet”.
130
19.9 Changing Password
Setting a password allows you to protect important information such as measurement data.
No password was set when the instrument was shipped. When setting a password for the first time,
leave the "Old password" box blank.
When a password has been set, the password screen will appear when the instrument is powered ON.
Input the password to continue.
• Password can be up to 16 characters in length. Input characters will be displayed as asterisks.

• To deactivate the password function, perform the new password setting procedure but enter a
"space" in the "New password" box.
G
• The password function will not be canceled when a cold boot is performed.
• The password must be input after powering ON the instrument from an external device when a
password has been set.
Items set
Old password : Input current password
New password : Input the new password
New password again : Input the new password again
131
19.10 Date and Time
Items set
Date : Manually input date or select from the drop-down calendar by tapping
G.
Time : Manually input time or set using [O]/[G].
Pressing {SPACE} will increment the selected section by 1.
& Date and Time

The instrument includes a clock/calendar function.
19.11 Restoring Default Settings
Perform a cold boot to return all items to factory settings. A cold boot will not erase surveying data in
instrument. However, if the data in the memory is important, BE SURE TO TRANSFER IT TO A
PERSONAL COMPUTER BEFORE PERFORMING A COLD BOOT.
G
• The password function will not be canceled.
• Resume function will be canceled.
PROCEDURE
1. "To perform a cold boot, while holding { } and {S.P.}, press { }.

"All Settings will be cleared. Are you sure?" is displayed.
2. Press [YES] to continue.
• Select [NO] and press {ENT}, or press {ESC} to cancel.
3. When the power is ON after the a cold boot, the screen for configuring the touch panel is
displayed. Configure the touch panel to continue.
C"8.1 Configuring the Touch Panel"
132
20.WARNING AND ERROR MESSAGES
The following is a list of the error messages displayed by the instrument and the meaning of each
message. If the same error message is repeated or if any message not shown below appears, the
instrument has malfunctioned. Contact your local dealer.
Backup battery dead. Clock display may no longer be correct.

The voltage supplied by the lithium battery either declines or is completely discharged.
Ask your local dealer to replace the battery for you.
Bad condition
The air is shimmering a lot, etc., measuring conditions are poor.
The center of the target cannot be sighted.

Resight the target.
Unsuitable distance measurement conditions when reflectorless measurement is set. When

reflectorless measurement is set, distance cannot be measured because the laser beam is
striking at least two surfaces at the same time.
Choose a single surface target for distance measurement.
C Precautions for setting prism: "10. TARGET SIGHTING"
Calculation error
During resection measurement the same point is registered multiple times. Set another known
point so that the known point coordinates do not coincide.
Coordinates identical to the known point coordinates observed during resection exist.
During surface area calculation, conditions necessary for calculations are not met. Check
conditions and try again.
An error occurred during calculation.
Device list is full !!

No more Bluetooth devices can currently be registered.
Delete unnecessary devices from the list and try again.
Disconnect Bluetooth
Wireless connection disconnected. Re-connect and try again.
Error: Read Build Info.

Error: Read JOG Setting
Error: Read OS Parameter
Error: Read sysflg
Error: Self check
Error: Write sysflg
Press [OK] to cancel the message. If this error message appears frequently, contact your local
dealer.
Incorrect password.
Input password does not match set password.
Input correct password.
133
20. WARNING AND ERROR MESSAGES
Input device name !!

Bluetooth device name not input. Input device name and complete device registration.
Input over 3 letters !

The input password consists of less than 3 characters. Input a password at least 3 characters in
length.
Motor error EXXX

A problem has occurred with the motor drive and operation stops.
Power the instrument OFF then ON to correct the problem.
If this error message appears frequently, contact your local dealer.
Need base pt. obs

During REM measurement, the observation of the target was not completed normally.
Reset and sight the prism and perform measurement again.
Need 1st obs

During missing line measurement, the observation of the starting position was not completed
normally.
Sight the starting position accurately and press [MEAS] to perform the measurement again.
New password Diff.

During new password setting, the passwords input twice are different.
Input new password twice correctly.
No solution
The calculation of the instrument station coordinates during resection does not converge.
Access the results and if necessary, perform the observations again.
Out of range
During gradient % display, the display range (less than ± 1000%) has been exceeded.
During REM measurement, either the vertical angle has exceeded horizontal ±89° or the
measured distance is greater than 9999.999m.
Install the instrument station far from the target.
Please input an address consisting of 12 hexadecimal characters (0 to 9, A to F)

The Bluetooth address is not input correctly for Bluetooth communication. Input the Bluetooth
address with 12 characters of 0 to 9 or A to F.
Signal off
The reflected light is not observed when distance measurement begins. Or, during measurement,
the reflected light has weakened or is blocked.
Either sight the target again or, when using a reflective prism, increase the number of reflective
prisms.
Target not found !!

The prism cannot be found within the Search area range.
134
20. WARNING AND ERROR MESSAGES
Temp Rnge OUT

The instrument is outside useable temperature range and accurate measurement cannot be
performed. Repeat measurement within the appropriate temperature range.
Tilt over range !!

The tilt angle exceeds the tilt angle compensation range of the sensor.
Level the instrument again.
Time out !!
Measurement is not carried out in the allotted time.
When designating the angle of rotation or automatically sighting the prism, there is a problem with
the positioning of the prism or the operation of the instrument and measurement is not obtained
within the fixed time.
Check the positioning of the instrument and prism and perform measurement again.
If observation is still not possible, sight the target manually.
When the telescope turns to nadir, it is not possible to search !!

The instrument cannot perform a search during Auto Pointing when the telescope is directed to
the nadir angle.
Set the telescope position within the measuring range and perform measurement again.
135
21.CHECKS AND ADJUSTMENTS
DS is a precision instrument that requires fine adjustments. It must be inspected and adjusted before
use so that it always performs accurate measurements.
• Always perform checking and adjustment in the proper sequence beginning from "21.1 Circular
Level" to "21.8 Laser Plummet (Option)".
• In addition, the instrument should be inspected with special care after it has been stored a long time,
transported, or when it may have been damaged by a strong shock.
• Make sure the instrument is securely set up and stable before performing checks and adjustments.
21.1 Circular Level
The bubble tube is made of glass, so it is sensitive to temperature changes or to shock. Check and
adjust it as outlined below.
G
• Be careful that the tightening tension is identical for all the adjusting screws. Also, do not over-
tighten the adjusting screws as this may damage the circular level.
PROCEDURE Checking and adjusting
1. Level while checking the display.

C"7.2 Levelling"
$
• Tap Tilt angle compensation icon in the
status bar or in Starkey mode to display electric
circular level.
G
• If the tilt sensor is misaligned, the circular level is
not adjusted correctly.
C"21.2 Tilt Sensor"
2. Check the position of the bubble of the circular
level.
If the bubble is not off-center, no adjustment is
necessary.
If the bubble is off-center, perform the following
adjustment.
136
21. CHECKS AND ADJUSTMENTS
3. First confirm the off-center direction.

Use the adjusting pin to loosen the circular level
adjustment screw on the side opposite to the
direction the bubble is displaced to move the
bubble to the center.
4. Adjust the adjusting screws until the tightening

tension of the three screws is the same to align
the bubble in the middle of the circle.
21.2 Tilt Sensor
If the tilt angle shown on the display shifts from tilt angle 0° (zero point), the instrument is not correctly
levelled. This will adversely affect angle measurement.
Perform the following procedure to cancel the tilt zero point error.
PROCEDURE Checking and adjusting
1. Carefully level the instrument. If necessary,

repeat the procedures to check and adjust the
bubble levels.
2. Select "Inst. cons." in <Configuration>
137
3. Select "Tilt offset".
4. Level the instrument until the X/Y tilt angles are

±1’. Wait a few seconds for the display to
stabilize, then read the current tilt angle in the X
(sighting) direction and Y (horizontal axis)
direction.
5. Press [OK]. The top of the instrument and

telescope rotate 180° from the current position.
6. Wait a few seconds for the screen to stabilize,

then read the automatically compensated angles
X2 and Y2.
7. In this state, calculate the following offset values

(tilt zero point error).
Xoffset = (X1+X2)/2
Yoffset = (Y1+Y2)/2
If one of the offset values (Xoffset, Yoffset)

exceeds ±10", adjust the value using the following
procedure.
When the offset value falls within the range ±10",
adjustment is not necessary.
Press {ESC} to return to <Instrument constants>.
8. Press [OK] to automatically rotate the top of the

instrument and telescope through 180°.
138
9. Confirm that the values are in the adjustment Results for target point
range.
If both correction constants are within the
range the current value ±1’, select [YES] to
renew the correction angle. <Instrument
constants> is restored. Continue to step 11.
If the values exceed the adjustment range,
select [NO] to cancel the adjustment and
return to the screen in step 4. Contact your
local dealer to perform the adjustment.

PROCEDURE Recheck
10. Select "Tilt offset".
11. Wait a few seconds for the display to stabilize,

X3 and Y3.
12. Press [OK] to automatically rotate the top of the

instrument and telescope through 180°.
13. Wait a few seconds for the display to stabilize,

X4 and Y4.
14. In this state, the following offset values (tilt zero

point error) are calculated.
Xoffset = (X3+X4)/2
Yoffset = (Y3+Y4)/2
When both offset values fall within the range ±10",
adjustment is completed.
Press {ESC} to return to <Instrument constants>.
If one of the offset values (Xoffset, Yoffset)

exceeds ±10", repeat the check and adjustment
procedures from the beginning. If the difference
continues to exceed ±10" after repeating the
check 2 or 3 times, have your local dealer perform
the adjustment.
139
21.3 Collimation
With this option you can measure collimation error in your instrument so that the instrument can
correct subsequent single face observations. To measure the error, make angular observations using
both faces.
PROCEDURE
1. Carefully level the instrument.
1. Select "Inst. cons." in <Configuration>.
2. Select "Collimation".
3. Sight the reference point in Face 1 and press

[OK]. Telescope rotates and vertical circle is
indexed.
G
• Do not look through the telescope eyepiece
while the motor drive is in operation. An eye
could be struck by the telescope and cause
injury.
140
4. Sight the reference point in Face 2 and press

[OK].
5. Press [YES] to set the constant.
• Press [NO] to discard the data and return to the

screen in step 3.
21.4 Reticle
With this option you can check the perpendicularity of the reticle and the horizontal/vertical positions
of reticle lines.
G
• Check the telescope reticle by sighting the target.
PROCEDURE Check 1: Perpendicularity of the reticle to the horizontal axis
2. Align a clearly visible target (the edge of a roof for

example) on point A of the reticle line.
141
3. Use the fine motion screws to align the target to

point B on a vertical line.
If the target moves parallel to the vertical line,
adjustment is unnecessary. If its movement
deviates from the vertical line, have our service
representative adjust it.
PROCEDURE Check 2: Vertical and horizontal reticle line positions
2. Install a target at a point about 100m in the

horizontal direction from the instrument.
3. While the Observation mode screen is displayed

and the telescope is in face left, sight the center
of the target and read out the horizontal angle A1
and the vertical angle B1.
Example:
Horizontal angle A1 = 18° 34' 00"
Vertical angle B1 = 90° 30' 20"
4. While the telescope is in face right, sight the

center of the target and read out the horizontal
angle A2 and the vertical angle B2.
Example:
Horizontal angle A2 = 198° 34' 20"
Vertical angle B2 = 269° 30' 00"
5. Do the calculations: A2-A1 and B2+B1

If A2-A1 is within 180°±20″and B2+B1 is within
360°±20″, adjustment is unnecessary.
Example:A2-A1 (Horizontal angle)
=198° 34' 20"- 18° 34' 00"
=180° 00' 20"
B2+B1 (Vertical angle)
=269° 30' 00" + 90° 30' 20"
=360° 00' 20"
If the difference is large even after repeating the
check 2 or 3 times, have our service
representative perform the adjustment.
142
21.5 Image Sensor Reticle
The internal image sensor is used for automatic sighting. The offset value is set to correct the position
of the image sensor in relation to the telescope reticle, but if for whatever reason the telescope reticle
and image sensor become misaligned, automatic sighting of the center of the prism cannot be
performed correctly. Check and adjust it as outlined below.
G
• Perform check and adjustment in weak sunlight and no scintillation.
• It may take up to 20 seconds for an offset value based on the measurement results to appear.
• Use Standard prism Prism-2. Using other prism types may result in adjustment inaccuracies.
PROCEDURE Checks and adjustments
2. Position the prism in a horizontal direction

approximately 50 meters from the instrument.
3. Select "Inst.cons." in <Settings>.
4. Select "Image Sensor-Reticle offset".
143
5. Use manual sighting to accurately sight the

target.
C"10.3 Manually Sighting the Target"
6. Press [OK].
7. Offset value (H, V) (New) is obtained from the set

Set offset value
offset value (H, V) (Current) and the
measurement results. The offset value is a
constant value that indicates the number of
degrees of misalignment between the center of
the telescope reticle and the center of the image
sensor. If the offset value obtained from the
measurement result is significantly larger than the
set offset value, press {ESC} and resight the
target.
If the offset value (H, V) obtained from the
measurement results continues to be significantly
large after repeated checks, adjustment is
necessary. Go to step 8.
Offset value obtained from
measurement
If one of the offset values exceeds the range, an
error message appears on the screen. Contact
your local dealer to perform the adjustment.
8. Press [OK] to renew the offset value.
144
21.6 Optical Plummet
G
• Be careful that the tightening tension is identical for all the adjusting screws.
• Also, do not over-tighten the adjusting screws as this may damage the circular level.
PROCEDURE Checking
1. Carefully level the instrument and center a survey

point precisely in the reticle of the optical
plummet.
2. Turn the upper part through 180° and check the

position of the survey point in the reticle.
If the surveying point is still centered, no
adjustment is necessary.
If the survey point is no longer centered in the
optical plummet, perform the following adjustment.
PROCEDURE Adjustment
3. Correct half the deviation with the levelling foot

screw.
4. Remove the optical plummet reticle cover.
5. Use the 4 adjusting screws of the optical plummet

to adjust the remaining half of the deviation as 1 (2)
shown below.
When the survey point is on the lower (upper) part
of the illustration:
Loosen the upper (lower) adjusting screw slightly,
and tighten the upper (lower) adjusting screw the
same amount to move the survey point to a point
directly under the center of the optical plummet.
(It will move to the line in the figure on the right.)
2 (1)
145
If the survey point is on the solid line (dotted line):

Loosen the right (left) adjusting screw slightly and,
tighten the left (right) adjusting screw by the same
amount to move the survey point to a point in the
center of the optical plummet. 4 3
(3) (4)
6. Check to make sure that the survey point remains

centered on the reticle even if the upper part of
the instrument is rotated.
If necessary, perform the adjustment again.
7. Replace the optical plummet reticle cover.
21.7 Additive Distance Constant
The additive distance constant K of the instrument is adjusted to 0 before delivery. Although it almost
never deviates, use a baseline with a known distance precision to check that the additive distance
constant K is close to 0 several times a year and whenever the values measured by the instrument
begin to deviate by a consistent amount. Perform these checks as follows.
G
• Errors in setting up the instrument and reflective prism or in sighting the target will influence the
additive distance constant. Be extremely careful to prevent such errors when performing these
procedures.
• Set up so that the instrument height and the target height are identical. If a flat place is not available,
use an automatic level to make sure the heights are identical.
PROCEDURE Check
1. Find an area of flat ground where two points

100m apart can be selected.
Set up the Instrument at point A and the reflective
prism at point B. Establish a point C half way
between points A and B.
2. Precisely measure the horizontal distance

between point A and point B 10 times and
calculate the average value.
146
3. Place the instrument at point C directly between

points A and B and set up the reflective prism at
point A.
4. Precisely measure the horizontal distances CA

and CB 10 times each and calculate the average
value for each distance.
5. Calculate the additive distance constant K as

follows.
K = AB - (CA+CB)
6. Repeat steps 1 to 5 two or three times.

If the additive distance constant K is within ±3mm
even once, adjustment is unnecessary.
If it always exceeds this range, have our service
representative perform an adjustment.
21.8 Laser Plummet (Option)
Checks and adjustments are performed using an adjustment target. Make an enlarged or reduced
copy of it.
PROCEDURE Check
1. Level the instrument and emit the laser plummet

beam.
C 7.2 Levelling
2. Rotate the upper part horizontally and place a
target so that it is aligned with the center of the
circle created by the rotating laser plummet
beam.
• Laser beam remains centered on the center of 5mm

the target – No adjustment necessary
• Laser beam strays from the center of the target
– Adjustment necessary.
• Laser beam draws a circle outside the target Adjustment target
circle – Contact your local dealer.
147
PROCEDURE Adjustment
1. Turn the laser plummet adjustment cap

anticlockwise and remove.
2. Emit the laser plummet beam.
3. Note the current position (x) of the laser beam.
4. Turn the upper part of the instrument horizontally

through 180° and note the new position (y) of the x y
laser beam. Desired final position
Adjustment will bring the laser beam to a point
midway along a line drawn between these two
positions.
5. Check the position of the desired final position.

Place a target so that its center is aligned with the
desired final position.
The remaining deviation will be adjusted using the Target
4 fine adjustment screws.
G :
• Be extremely careful to adjust all the fine
adjustment screws by the same amount so that
none will be over-tightened.
• Turn screws clockwise to tighten.
Fine adjustment screws

6. When the laser beam is on the upper (lower) part
of Fig. A the up/down adjustment is made as
follows:
c Insert the provided hexagon key wrench into
both the upper and lower screws. Desired final position
Fig. A
148
d Slightly loosen the upper (lower) screw and

tighten the lower (upper) screw. Make sure
that the tightening tension for both screws is
identical. Continue to adjust until the laser
beam is on the horizontal line of the target.
7. When the laser beam is in the right (left) part of

Fig. B the left (right) adjustment is made as
follows:
c Insert a hexagon key wrench into both the
left and right screws.
d Slightly loosen the right (left) screw and
tighten the left (right) screw. Make sure that Fig. B
the tightening tension for both screws is
identical.
Continue to adjust until the laser beam is
aligned with the target center.
8. Turn the upper part of the instrument horizontally

and check that the laser beam is now aligned with
the target center.
9. Re-attach the laser plummet adjustment cap.
$
• Tightening each of the fine adjustment screws moves the laser plummet beam in the directions
shown below.
Up
Tighten "Up" screw
Tighten "Right"
screw Tighten "Left"
Left Right screw
Tighten "Down" screw

Down
Fine adjustment screws Laser plummet adjustment cap
pointing towards user
149
22.POWER SUPPLY SYSTEM
Operate your instrument with the following combinations of power equipment.
G
• When using an external battery, mount the BDC70 in place to maintain the balance of the
instrument.
• Never use any combination other than those indicated below. If you do, the instrument could be
damaged.
Those indicated by * are standard accessories. Others are optional accessories.
Battery* Charger* Power cable*

BDC70 CDC68/68A EDC113A/C
(110 to 240 VAC)
EDC113B
(110 to 125 VAC)
etc.
Interface cable AC/DC converter
<&DEOH ('& ('&

WR9$&
('&
Power cable External battery Charger

('& %74 &'& AC/DC converter
9'&$K ('&
WR9$&
('&
Interface cable
<&DEOH
For car cigarette lighter
('& ('&
9'&
Power cable
('& Car battery
$
• Dedicated power cables differ according to the country or the area where the instrument is used.
Contact your local dealer for the details.
• By using the Y cable the instrument can perform RS232C communication (D-sub 9-pin) at the same
time as connecting to an external power source.
150
23.PRISM SYSTEM
Arrangement according to your needs is possible.
Target pole-2
(not used with 9 prisms)
Prism-2
Tilting prism Tilting prism Single prism Triple prism Tilting triple 9 prism
holder-2 holder-3 holder-2 holder-2 prism holder-1 holder-2
with target
plate-2 Plug-3
Tribrach Tribrach
adaptor-2 adaptor-S2
Pole adaptor- A
Pole adaptor- F2
Tribrach Optical plummet tribrach
Tilt single prism unit Fixed 3 prisms unit Fixed 9 prisms unit
Tripod
360° Prism ATP1 360° Sliding Prism ATP1S
• Use the above prisms after setting them at the same height as the instruments. To adjust the height
of prism set, change the position of fixing screws.
• Plug-3 is necessary for the tribrach adaptor-2, tribrach adaptor-S2 and pole adaptor-F2 to coincide
with the height of this series.
151
24.OPPTIONAL ACCESSORIES
The following are optional accessories which are sold separately from the instrument.
C Power supply and target optional accessories: "22. POWER SUPPLY SYSTEM", "23. PRISM
SYSTEM".
I Plumb bob
The plumb bob can be used to set up and center
the instrument on days when there is little wind. To
use the plumb bob, unwind its cord, pass it through
the cord grip piece as shown in the figure to adjust
its length, then suspend it from the hook attached
to the centering screw.
I Tubular compass (CP7)

Slide the tubular compass into the tubular
compass slot, loosen the clamp screw, then rotate
the top part of the instrument until the compass
needle bisects the index lines. The telescope's Tubular
compass slot
face 1 sighting direction in this position will
indicate magnetic north. After use, tighten the
clamp and remove the compass from the slot.
G
• The tubular compass is susceptible to the
influence of nearby magnets or metal. Such
influence could cause it to fail to accurately
indicate magnetic north. Do not use magnetic
north as indicated by this compass for base line
surveying.
I Telescope eyepiece lens (EL7)

Magnification: 40X
Field of view: 1° 20'
152
24. OPPTIONAL ACCESSORIES
I Diagonal eyepiece (DE27)

The diagonal eyepiece is convenient for DE27
observations near the nadir and in narrow spaces.
Magnification: 30X
After removing the handle from the instrument

loosen the attachment screw to remove the
telescope eyepiece. Then screw the diagonal lens
into place.
CHandle removal method: "4.1 Parts of the
Instrument "Handle""
G
• Do not perform vertical rotation of the telescope
when using the diagonal eyepiece. The diagonal
eyepiece may strike the instrument causing
damage.
I Solar filter (OF3A)

When sighting targets where glare is present,
solar observations for example, attach it to the
objective lens of the instrument to protect its
interior and the eyes of its operator. The filter part
can be flipped up without being removed.
G
• Do not perform vertical rotation of the telescope
when using the solar filter. The solar filter may
strike the instrument causing damage.
I Power cable/Interface cable

Connect the instrument to a host computer using the following cables.
Cable Notes
DOC210 Pin number and signal level : RS232C compatible
EDC211 (Y cable) D-Sub connector : 9 pins (female)
EDC212 (Y cable)
$
• By using the Y cable the instrument can perform RS232C communication (D-Sub 9-pin) at the
same time as connecting to an external power source.
I 2-point target (2RT500-K)

This target is used for two-distance offset
measurement.
Prism constant correction value: 0
153
25.SPECIFICATIONS
Except where stated, the following specifications apply to all DSs.
Telescope
Length 168mm
Aperture 45mm (1.8 inch) (EDM: 50mm (2.0 inch))
Magnification 30X
Image Erect
Resolving power: 2.5"
Field of view 1°30' (26m/1,000m)
Minimum focus 1.3m (4.3ft)
Focussing screw 1 speed
Reticle illumination 5 brightness levels
Angle measurement
Horizontal and Vertical circles type
Rotary absolute encoder
Detecting
DS-101AC/102AC/103AC: 2 sides
DS-105AC: 1 side
Angle units Degree/Gon/Mil (selectable)
Minimum display
DS-101AC/102AC: 0.5"(0.0001gon/0.002mil)/1" (0.0002gon/0.005mil) (selectable)
DS-103AC/105AC: 1" (0.0002gon/0.005mil)/5" (0.0010gon/0.020mil) (selectable)
Accuracy
DS-101AC: 1" (0.0003gon/0.005mil)
DS-102AC: 2" (0.0006gon/0.010mil)
DS-103AC: 3" (0.001gon/0.015mil)
DS-105AC: 5" (0.0015gon/0.025mil)
(ISO 17123-3 : 2001)
Collimation compensation On/Off (selectable)
Measuring mode
Horizontal angle: Right/Left (selectable)
Vertical angle: Zenith/Horizontal/Horizontal ±90°/% (selectable)
Tilt angle compensation

Type Liquid 2-axis tilt sensor
Correction unit 1"
Range of compensation ±6’
Automatic compensator ON (V & H/V)/OFF (selectable)
Tilt offset Can be changed
Distance measurement
Measuring method Coaxial phase-contrast measuring system
Signal source Red laser diode 690nm
Class 3R
(IEC60825-1 Ed. 2.0: 2007/FDA CDRH 21CFR Part1040.10 and
1040.11 (Complies with FDA performance standards for laser
products except for deviations pursuant to Laser Notice No.50, dated
July 26, 2001.))
(When the prism or reflective sheet is selected in Config mode as
target, the output is equivalent to Class 1)
154
25. SPECIFICATIONS
Measuring range*9 (Using the following reflective prism/reflective sheet target during
normal atmospheric conditions*1/ *2 is good atmospheric conditions)
360° Prism ATP1/ATP1S:*2 1.3 to 1,000 m (3,280ft)*3
Prism-5: 1.3 to 500m (1,640ft)*7
Prism-2 X 1: 1.3 to 5,000m (16,400ft)*7
(to 6,000m) (19,680ft)*7
Prism-2 X 3: to 8,000 m (26,240ft)*7
(10,000m) (32,800ft)*7
Reflective sheet RS90N-K: 1.3 to 500m (1,640ft)*4
Reflective sheet RS50N-K: 1.3 to 300m (980ft)*4
Reflective sheet RS10N-K: 1.3 to 100m (320ft)*4
Reflectorless (White) : 0.3 to 800m (2,620ft)*5
(to 1,000m) (3,280ft)*6
Prism (tracking)*3 :1.3 to 1,000m (3,280ft)
Refrective sheet target (tracking)*4
:1.3 to 350m (1,140ft)
Reflectorless (White) (tracking)*5
:0.3 to 300m (980 ft)
Minimum display
Fine measurement: 0.0001m (0.001ft/ 1/16 inch)/0.001 m (0.005ft/ 1/8 inch)
Rapid measurement: 0.001 m (0.005ft/ 1/8 inch)
Tracking measurement: 0.01 m (0.1ft/ 1/2 inch)
Maximum slope distance display (Except for tracking)
12,000.000m (39,370ft) (using prism or reflective sheet target)
1,200.000m (3,930ft) (Reflectorless)
Distance unit m/ft/inch (selectable)
Accuracy (D: measurement distance; Unit: mm) (Under normal atmospheric conditions*1)*7, *9
(Using prism or using 360° Prism ATP1/ATP1S*3)
Fine measurement: ±(1.5 + 2 ppm X D) mm
Rapid measurement: ±(5 + 2 ppm X D) mm
(Using reflective sheet target)*4
Fine measurement: ±(2 + 2 ppm X D) mm
Rapid measurement: ±(5 + 2 ppm X D) mm
(Reflectorless (White))*5
Fine measurement:
±(2 + 2ppm X D) mm (0.3 to 200m)*8
±(5 + 10ppm X D) mm (over 200 to 350m)
±(10 + 10ppm X D) mm (over 350 to 10,00m)
Rapid measurement:
±(6 + 2ppm X D) mm (0.3 to 200m)
±(8 + 10ppm X D) mm (over 200 to 350m)
±(15 + 10ppm X D) mm (over 350 to 10,00m)
(ISO 17123-4 : 2001)
Measurement mode Fine measurement (single/repeat/average)/Rapid measurement
(single/repeat)/Tracking (selectable)
Measuring time (fastest time under good atmospheric conditions*2, no compensation,
EDM ALC at appropriate setting, slope distance)
Fine measurement: less than 1.5 sec + every 0.9 sec or less
Rapid measurement: less than 1.3 sec + every 0.6 sec or less
Tracking measurement: less than 1.3 sec + every 0.4 sec or less
155
25. SPECIFICATIONS
Atmospheric correction
Temperature input range: - 30 to 60°C (in 0.1°C step)/ - 22 to 140°F (in 1°F step)
Pressure input range: 500 to 1,400 hPa (in 1hPa step)
375 to 1,050 mmHg (in 1mmHg step)
14.8 to 41.3 inchHg (in 0.1inchHg step)
ppm input range: -499 to 499 ppm (in 1 ppm step)
Prism constant correction -99 to 99 mm (in 1 mm step)
0mm fixed for reflectorless measurement
Earth curvature and refraction correction
No/Yes K=0.142/Yes K=0.20 (selectable)
Sea level correction No/Yes (selectable)
*1 : Slight haze, visibility about 20 km, sunny periods, weak scintillation.

*2 : No haze, visibility about 40 km, overcast, no scintillation.
*3 : Figures when both the elevation and depression angles of the laser beam are within 15° and
the instrument is facing the 360° Prism.
*4 : Figures when the laser beam strikes within 30° of the reflective sheet target.
*5 : Figures when using Kodak Gray Card White side (reflection factor 90%) and brightness level
is less than 5,000 lx.
*6 : Figures when using Kodak Gray Card White side (reflection factor 90%) and brightness level
is less than 500 lx.
*7 : Face the target toward the prism during the measurement with the distance at 10 m or less.
*8 : Accuracy is (5 + 2 ppm X D) mm for distance range 0.3 to 0.66m.
*9 : Figures will change depending on the target reflection factor, weather conditions and location
conditions.
156
25. SPECIFICATIONS
Auto Pointing
Measuring method Pulse laser transmitter and image sensor with co-axial optics
Signal source (emittted beam) infrared laser diode (980 nm)
Class 1
(IEC60825-1 Ed. 2.0: 2007/FDA CDRH 21 CFR Part 1040.10 and
1040.11 (Complies with FDA performance standards for laser
products except for deviations pursuant to Laser Notice No.50, dated
June 24, 2007.))
Viewing angle ± 45’
Measuring range H: 360° (full transit)
V: Elevation angle 90° (when handle is attached: 70°) ,
Depression angle 41°*10
Auto Pointing measurement range*11
360° Prism ATP1/ATP1S: 2 to 600 m (1,960 ft)*3,14
Prism-5: 1.3 to 600 m (1,960 ft)
Prism-2: 1.3 to 1,000 m (3,280 ft)
Reflective sheet RS10/30/50: 5 to 50 m (160 ft)*12,*13
Reflective sheet RS90: 10 to 50 m (160 ft)*12,*13
Time to completed Auto Pointing*11
(When prism in field-of-view, at 100 m distance)/(using RS90N-K, at
50 m distance)
4 to 8 sec.*15
Sighting accuracy (standard deviation)*11 (fine measurement)
Prism: 1.2 mm or less (equivalent angle) (to 100 m),
(0.3 + 9ppm X D) or less (equivalent angle) (100 m and over)
Reflective sheet RS90N-K: 2 mm or less (equivalent angle)*12,*13
*10 : Measurering time may be longer around elevation angle 90°, because the tilt compensation
is not in operation.
*11 : No haze, visibility over 20 km, slightly overcast (less than 30000 lx), no scintillation.
*12 : When using a reflective sheet for Auto Pointing, the size of sheet (10 to 90 mm) must be
selected to correspond to the distance being measured. Use smaller reflective sheets for
shorter distances.
*13 : Figures when the Auto Pointing beam strikes within 15° of the reflective sheet target.
*14 : Figures when the Auto Pointing beam strikes within elevation and depression angle 15° of the
360° prism.
*15 : Measurering time may be longer when search area is widely set and target is positioned far
from the sighting direction.
Motor
Type DC motor drive
Motion range 360°(Vertical and horizontal)
Rotation speed 70°/sec (at 20°C)
(Rotating time: about 8 sec. (when rotating 180°, tilt compensation
off, at 20°C))
Fine motion Operated by jogs (minimal unit of motion is about 1")
157
25. SPECIFICATIONS
Guide Light
Light source LED (red 626 nm/green 524 nm)
Distance 1.3 to 150m*1
Visible range Right and Left/Upward and Downward:± 4° (7m/100m)
Resolving power at center area (width)
4’ (about 0.12/100m)
Brightness 3 levels (bright/normal/dim)
Internal memory
Capacity 500 MB (includes memory for program files)
External memory
USB flash memory (up to 8 GB)
Data transfer
Data input/output Asynchoronous serial, RS232C compatible
USB USB Ver. 1.1, Host (Type A) and Client (Type miniB)
Bluetooth wireless communication (option)

Transmission method FHSS
Modulation GFSK
Frequency band 2.402 to 2.48GHz
Bluetooth profile SPP, DUN
Power class Class 1
Usable range to 300m*16,17
Authentication Yes/No (selectable)
*16 : No obstacles, few vehicles or sources of radio emissions/interference in the near vicinity of
the instrument, no rain
*17 : Usage range could be shorter depending on specifications of Bluetooth device to
communicate.
158
25. SPECIFICATIONS
Power Supply
Power source Rechargeable Li-ion battery BDC70
Working duration at 20 °C
(Fine distance measurement (single) using Auto Pointing, repeated every 30 sec)
BDC70: about 5hours
BT-73Q (external battery, optional accessory): about 14.5 hours
Battery state indicator 4 levels
Auto power-off 5 levels (5/10/15/30 min/Not set) (selectable)
External power source 6.7 to 12V
Battery (BDC70)
Nominal voltage: 7.2V
Capacity: 5,240 mAh
Dimensions: 40(W) x 70 (D) x 40 (H) mm
Weight: about 197g
Charger (CDC68/68A)
Input voltage: AC100 to 240V
Charging time per battery (at 25°C):
BDC70: about 5.5 hours (Charging can take longer than the times stated
above when temperatures are either especially high or low.)
Charging temperature range: 0 to 40°C
Storage temperature range:-20 to 65°C
Size: 94 (W) X 102 (D) X 36 (H) mm
Weight: about 170g
General
Operating system Windows Embedded CE 6.0
Display 3.5 inch Transmissive TFT QVGA color LCD
Backlight: LED: 9 brightness levels (0 to 8) (selectable)
Touch panel: Resistance-sensitive analog type
Keyboard 26 keys
Key backlight:Yes
Trigger key Yes (right side)
Sensitivity of levels
Circular level: 10'/2 mm
Electronic Circular levels: Graphic display range: 6' (inner circle)
Digital display range:±6' 30"
Optical plummet
Image: Erect
Magnification: 3X
Minimum focus: 0.3 m
Laser plummet (option)
Signal source: Red laser diode 635 ±10nm (Class 2 IEC60825-1 Ed. 2.0:2007/FDA
CDRH 21CFR Part 1040.10 and 1040.11 (Complies with FDA
performance standards for laser products except for deviations
pursuant to Laser Notice No.50, dated June 24, 2007.))
Beam accuracy: 1mm or less (when tripod head height is 1.3m).
Spot diameter: ø3mm or less
Brightness control: 5 levels
Auto power-off: Provided (power cut off after 5 minutes)
159
25. SPECIFICATIONS
Calendar/clock function Yes

Laser-pointer function ON/OFF (selectable)
Operating temperature: -20 to 50 °C (-4 to 122 °F)
Storage temperature range -30 to 60°C (-22 to 158 °F) (no condensation)
Dust and water resistance IP65 (IEC 60529:2001)
Instrument height: 196 mm from levelling base mounting surface
Size (with handle):
Display on one side: 207 (W) X 174 (D) X 372 (H) mm
Display on both sides: 207 (W) X 190 (D) X 372 (H) mm
(when using levelling base TR-101, except for projections)
Weight 6.1kg (13.4lb)
(with BDC70 and levelling base)
160
26.EXPLANATIONS
26.1 High Accuracy with the 360° Prism
Sighting can be more accurately performed by facing the 360° Prism toward the instrument. The 360°
Prism should be set up so that a pair of diametrically-opposed hexagonal points on its rubber flanges
are aligned with the sighting direction of the instrument (see the diagram below).
: Hexagonal points
When using the ATP1S, the 360° Prism should be set up so that a pair of diametrically-opposed marks
on top of the prism are aligned with the sighting direction of the instrument.
: Prism sighting direction
161
26. EXPLANATIONS
26.2 Manually Indexing the Vertical Circle by Face Left, Face Right
Measurement
The 0 index of the vertical circle of your instrument is almost 100% accurate, but when it is necessary
to perform particularly high precision angle measurements, you can eliminate any inaccuracy of the 0
index as follows.
G
• If the power is cut off, the vertical circle indexing is ineffective. Do it again every time the power is
turned on.
PROCEDURE
1. Select “Obs.condition” in <Configuration>. Set “V

manual” (vertical circle indexing method) to “Yes”.
C"19.1 Observation Conditions"
<V manual 0 set> is displayed.
3. Accurately sight a clear target with a distance of

about 30m in the horizontal direction with the
telescope in face left.
Press [OK]. The vertical angle V2 is displayed
under "Take F2".
4. Turn the upper part through 180° and clamp it.

Then set the telescope in the face right position
and accurately sight the same target.
Press [OK].
The vertical and horizontal angles are displayed.
This concludes the vertical circle indexing
procedure.
162
27.REGULATIONS
Region/ Directives/
Labels/Declarations
Country Regulations
U.S.A. FCC-Class A FCC Compliance

WARNING:
Changes or modifications to this unit not expressly approved by the
party responsible for compliance could void the user's authority to
operate the equipment.
NOTE:
This equipment has been tested and found to comply with the limits
for a Class A digital device pursuant to Part 15 of the FCC Rules.
These limits are designed to provide reasonable protection against
harmful inter-ference when the equipment is operated in a commercial
environment. This equipment generates, uses, and can radiate radio
frequency energy and, if not installed and used in accordance with the
operator’s manual, may cause harmful interference to radio
communications. Operation of this equipment in a residential area is
likely to cause harmful interference in which case the user will be
required to correct the interference at his own expense.
Means of conformity
This device complies with part 15 of the FCC Rules, Operation is
subject to the following two conditions: (1) This device may not cause
harmful interference, and (2) this device must accept any interference
received, including interference that may cause undesired operation.
This transmitter must not be co-located or operated in conjunction

with any other antenna or transmitter.
This equipment complies with FCC radiation exposure limits set forth
for uncontrolled equipment and meets the FCC radio frequency (RF)
Exposure Guidelines in Supplement C to OET65. This equipment has
very low levels of RF energy that is deemed to comply without
maximum permissive exposure evaluation (MPE). But it is desirable
that it should be installed and operated with at least 20cm and more
between the radiator and person’s body (excluding extremeties:
hands, wrists, feet and ankles).
Declaration of Conformity
Model Number: DS series
Trade Name: TOPCON CORPORATION
Manufacture
Name: TOPCON CORPORATION
Address: 75-1, Hasunuma-cho, Itabashi-ku, Tokyo,
174-8580 JAPAN
Country: JAPAN
U.S.A. Representative
Responsible party: TOPCON POSITIONING SYSTEMS,INC.
Address 7400 National Drive Livermore, CA94551, U.S.A
Telephone number: 925-245-8300
163
27. REGULATIONS
Region/ Directives/
Labels/Declarations
Country Regulations
Californi Proposition
a, 65
U.S.A.
Californi Perchlorate
a, Material
U.S.A. (CR Lithium
Battery)
Californi Recycling
a and Batteries
NY,
U.S.A.
164
27. REGULATIONS
Region/ Directives/
Labels/Declarations
Country Regulations
Canada ICES-Class A This Class A digital apparatus meets all requirements of Canadian
Interference-Causing Equipment Regulations.
Cet appareil numérique de la Class A respecte toutes les exigences
du Règlement sur le matériel brouilleur du Canada.
This class A digital apparatus complies with Canadian ICES-003.

Cet appareil numerique de la classe A est conforme a la norme
NMB-003 du Canada.
Operation is subject to the following two conditions: (1) this device

may not cause interference, and (2) this device must accept any
interference, including interference that may cause undesired
operation of this device.
This equipment complies with IC radiation exposure limits set forth

for uncontrolled equipment and meets RSS-102 of the IC radio
frequency (RF) Exposure rules. This equipment should be installed
and operated with at least 20cm and more between the radiator and
person’s body (excluding extremeties: hands, wrists, feet and
ankles).
EU EMC-Class
B
R&TTE-
Class 2
EU R&TTE- R&TTE Directive

Class 2
DS series
Hereby, TOPCON CORP., declares that the above-mentioned
equipment is in compliance with the essential requirements and
other relevant provisions of Directive 1999/5/EC.
Please inquire below if you wish to receive a copy of Topcon's

Declaration of Conformity.
Topcon Europe Positioning B.V.

Essebaan 11, 2908 LJ Capelle a/d IJssel,
The Netherlands
Tel:+31-10-4585077 Fax:+31-10-2844949
http://www.topcon-positioning.eu/index.asp
165
27. REGULATIONS
Region/ Directives/
Labels/Declarations
Country Regulations
EU WEEE
Directive
EU EU Battery
Directive
Australi C-Tick
a
166
28.INDEX
A
ACK mode .................................................................................................................................. 43
Adjusting backlight brightness/turning the reticle illumination and key backlight ON/OFF ...... 115
Atmospheric correction factor .................................................................................................. 118
AUTO AIM .................................................................................................................................. 53
Automatic tilt angle compensation mechanism ........................................................................ 113
B
Bluetooth connections ................................................................................................................ 42
Bluetooth device address ........................................................................................................... 45
C
Cold boot .................................................................................................................................... 40
Collimation correction .............................................................................................................. 113
Color setting ............................................................................................................................. 116
D
Date and Time ......................................................................................................................... 132
E
EDM ALC ................................................................................................................................. 116
Eliminating parallax .................................................................................................................... 56
F
Fixed velocity rotation ................................................................................................................ 61
G
Guide light .................................................................................................................................. 10
H
Hdist ......................................................................................................................................... 112
Horizontal angle settings ...................................................................................................... 73, 79
Horizontal jog ............................................................................................................................. 11
I
Inch (Fraction of an inch) ......................................................................................................... 130
Instrument height mark .............................................................................................................. 10
K
Key backlight ............................................................................................................................ 116
L
Laser-pointer function ................................................................................................................ 10
Laser-pointer off ....................................................................................................................... 116
P
Power-saving automatic cut-off/Backlight Off .......................................................................... 115
Precaution when performing resection ...................................................................................... 84
Prism constant correction value ............................................................................................... 117
Problems Powering OFF ............................................................................................................ 41
Power-saving automatic cut-off (Power on command) ............................................................ 115
R
Resection calculation process ................................................................................................... 83
Resume function ........................................................................................................................ 39
S
Sea level correction ................................................................................................................. 113
Search operation during Auto pointing ....................................................................................... 54
Sighting collimator ...................................................................................................................... 11
Sighting manually ....................................................................................................................... 57
Slope area ................................................................................................................................ 107
167
28. INDEX
T
Terminate ...................................................................................................................................43
Trigger key .................................................................................................................................11
TURN .........................................................................................................................................54
V
V mode (vertical angle display method) ...................................................................................113
Vertical Jog .................................................................................................................................11
168
http://www.topcon.co.jp
Please see the attached address list or the following website for contact addresses.
GLOBAL GATEWAY http://global.topcon.com/
©2013 TOPCON CORPORATION

ALL RIGHTS RESERVED

DS Series: DS-101AC DS-102AC DS-103AC DS-105AC

Uploaded by

Copyright:

Available Formats

DS Series: DS-101AC DS-102AC DS-103AC DS-105AC

Uploaded by

Document Information

Original Title

Copyright

Available Formats

Share this document

Share or Embed Document

Sharing Options

Did you find this document useful?

Is this content inappropriate?

Copyright:

Available Formats

DS Series: DS-101AC DS-102AC DS-103AC DS-105AC

Uploaded by

Copyright:

Available Formats

SURVEYING INSTRUMENTS

The following conventions are used in this manual.

G : Indicates precautions and important items which should be read before

C : Indicates the chapter title to refer to for additional information.

$ : Indicates supplementary explanation.

& : Indicates an explanation for a particular term or operation.

{Key} etc. : Indicates keys on the operation panel.

<Screen title> etc. : Indicates screen titles.

• Except where stated, “DS” means DS-101AC/102AC/103AC/105AC in this manual.

• KODAK is a registered trademark of Eastman Kodak Company.

This is the mark of the Japan Surveying

Ignoring this indication and making an operation error could possibly

Ignoring this indication and making an operation error could possibly

Do not perform disassembly or rebuilding. Fire, electric shock, burns, or hazardous

D Do not short circuit. Heat or ignition could result.

Bluetooth wireless technology

Use the instrument at a distance of at least 22 cm from anyone with a cardiac

Tribrach Clamp and Handle

• When the instrument is shipped, the tribrach clamp is held

Precautions concerning water and dust resistance

The Lithium Battery

The Levelling Base

Exporting this product

Exceptions from responsibility

• EDM device in objective lens: Class 3R Laser Product

Laser beam emitted

(only when laser plummet

Parts and functions of the instrument

19 Tubular compass slot

& Instrument height mark

& Laser-pointer function

& Guide light

(When seen from the objective lens side

I Guide light status

& Vertical and Horizontal Jogs

& Trigger key

& Sighting collimator

The Bluetooth antenna allows communication via

Detaching/attaching the Handle

Detaching the instrument from the levelling base

1. Loosen the levelling base locking screw by

2. Turn the tribrach clamp counterclockwise to

3. Lift the instrument to detach.

Attaching the instrument to the levelling base

1. Check that the levelling base locking screw

2. Align (1) and (2) and lower the instrument onto

4. Turn the levelling base locking screw

4.2 Mode Structure

Observation mode (switching by tab)

C“19.Changing the settings”

]PRG_ ●Starkey mode

4.3 Bluetooth Wireless Technology

Radio interference when using Bluetooth technology

I When using the DS in proximity to IEEE802.11b or IEEE802.11g standard wireless LAN

I Do not use the DS in proximity to microwaves.

I Refrain from using the DS in proximity to televisions and radios.

• Televisions and radios use a different frequency band to Bluetooth communications.

Precautions regarding transmission

I For best results