Materials Research.

2018; 21(1): e20170469

DOI: http://dx.doi.org/10.1590/1980-5373-MR-2017-0469

Effect of Austenitizing Temperature on Mechanical Properties of the Mixed Bainite -

Martensite Microstructure in CrMoV Steel
Parsa Abbaszadeha*, Shahram Kheirandisha, Hassan Saghafiana, Mohammad hossein Goodarzya

a
Center of Excellence for Advanced Materials and processing (CEAMP), School of Metallurgy and
Materials Engineering, Iran University of Science & Technology (IUST), Tehran, Iran

Received: May 05, 2017; Revised: September 23, 2017; Accepted: October 05, 2017

The effect of austenitizing temperature on mechanical properties of the mixed bainite - martensite
microstructure in CrMoV steel was studied in the present work. The result showed that at low austenitizing
temperature (910°C - 1000°C), the mixed microstructures containing 12-28% volume fraction of lower
bainite showed higher yield and tensile strength than fully martensitic microstructure. The partitioning
of the prior austenite grain by lower bainite was found to cause a refinement of the martensite packet
size. In addition the strength of the lower bainite in the mixed microstructure is enhanced by plastic
constraint induced by the surrounding stronger martensite. By increasing the austenitizing temperature
from 1000°C to 1200°C (40min), the YS, UTS, %EL, %RA and CVN impact energy decreased for all
samples. This is attributed mainly to the increase in austenite grain size and width of bainite sheaves.

Keywords: Microstructure, CrMoV, Mechanical properties, lower bainite

1. Introduction presence of the upper bainite in the mixed microstructure in

Ultrahigh strength medium carbon low alloy CrMoV(D6AC) an AISI 4330V led to a significant improvement in toughness
steel has been used as a structural material for several critical without affecting the strength of the fully martensitic
applications such as landing gears, shafts and motor cases, microstructure. However no beneficial effect of the lower
etc. It has good notch toughness and does not exhibit temper bainite on mechanical properties was observed in the lower
embrittlement1. bainite- martensite microstructure. The above survey of
Quenching followed by tempering process is the literature serves to show the complex effects of the mixed
most common heat treatment cycle for the hardening and or multiphase microstructures on mechanical properties
strengthening of ultrahigh strength medium carbon low alloy of ultra high strength low alloy steels. Because of lack of
steels2. However, increase in strength is usually associated any report regarding the effect of austenitizing temperature
with decrease in the ductility values limiting the structural on the mechanical properties of the mixed lower bainite -
applications of these steels3,4. An approach to overcome this martensite microstructure, the current work was undertaken
problem is to develop steels, having mixed or multiphase to study of the effect of austenitizing temperature on the
microstructures5-8. However, inferior mechanical properties mechanical properties of the mixed lower bainite - martensite
have also been reported for these steel compared with those microstructure in CrMoV steel.
having conventional microstructures8.
Salami et al.9,10 reported that the mechanical properties 2. Experimental Procedure
of tempered martensite are more favorable than those of
ferrite - bainite - martensite microstructure in 42CrMo4 The CrMoV steel was received as forged bars which
steel. They demonstrated that the high density of interphase were 85mm in diameter. The chemical composition of the
boundary in ferrite - bainite - martensite microstructure was steel is given in Table 1.
the main reason for the inferior mechanical properties of Test plates of 60mm × 130mm with a thickness of 6 and
such a mixed microstructure. 12mm were cut from the steel bars. The length of the plates
Tomita et al.11 suggested that the lower bainite which was in the longitudinal direction of the bar. Each plate was
appears in acicular form and divides the prior austenite first stress relieved at 650ºC and then fully annealed at 850
grain, which is associated with martensite, provided a better ºC for 2hrs. The austenitizing was carried out in an argon
combination of mechanical properties in AISI 4340 Steel. atmosphere furnace with a temperature accuracy of ±4ºC at
On the other hand the mixed microstructure of upper bainite different temperatures of 910ºC, 1000ºC, 1100ºC and 1200ºC
- martensite significantly lowers mechanical properties for 40min. Following the austenitizing, specimens were either
compared to the martensitic microstructures12-14. Contrary oil quenched to produce martensite, or isothermally held
to the Tomita investigation, Rao et al.15 suggested that the in a salt bath of 330 ºC above the MS for different holding
times (3.5, 5, 7.5, 10, 12.5, 15, 20 and 840 min) then oil
*e-mail: eurak@alumni.iust.ac.ir
2 Abbaszadeh et al. Materials Research

Table 1. Chemical composition of Cr MoV steel (Wt. %).

Element C Si Mn P S Cr Mo Ni V Fe
Wt. % 0.47 0.26 0.76 0.009 0.004 0.99 0.93 0.54 0.11 Bal.

quenched to obtain mixed microstructure of lower bainite surfaces of impact specimens were examined by scanning
- martensite with varying amounts of the lower bainite. A electron microscopy (SEM) in order to characterize the
fully lower bainite microstructure was obtained by quenching impact fracture mode.
the specimens in a salt bath at 330 ºC for 24 hrs. Finally, all
specimens were tempered at 200ºC for 2hrs. 3. Results and Discussion
After heat treatment, the plates were machined and
ground to the final thicknesses of 4 and 10mm to eliminate 3.1. Metallographic observations
any decarburized layer. Sub size tensile specimens which are
4mm thick with a gauge length of 25mm were wire cut from Figure 1 shows typical optical and scanning electron
a plate which is 4mm thick in accordance with ASTM E8M16. micrographs of the mixed lower bainite - martensite
Charpy V - notch impact specimens were wire cut from a microstructures after austenitizing at 910°C. Fig.1a
plate which is 10mm thick in accordance with ASTM E2317. shows optical micrographs of the mixed microstructure
Tensile tests were carried out using a 200KN electromechanical of the lower bainite - martensite, in which the dark etched
universal machine at constant cross- head speed of 5mm/min. regions correspond to lower bainite and the white regions
The charpy V - notch impact properties were determined corresponding to martensite. Micro hardness tests showed
using a 300J metal pendulum impact machine. A minimum that the hardness values of dark regions (lower bainite) and
of seven impact and three tensile specimens were tested in white regions (martensite) are 483 and 745 HV, respectively
each case. The microstructures were examined by optical and and confirm the metallography observation. Corresponding
scanning electron microscopes. Metallography specimens scanning electron micrographs of the mixed microstructure of
were cut from the impact test pieces. The specimens were the lower bainite - martensite (Fig.1b) reveals that the lower
etched with hot (75ºC) supersaturated aqueous solution of bainite associated with martensite appears in acicular form
picric acid to reveal the prior austenite grain size. In order and partitions the prior austenite grains, therefore refines
to reveal the lower bainite in a matrix of martensite, the the martensite packet size. This type of microstructures is
specimens were etched with a solution of 4wt. % picral plus similar to the one reported by Wen et al.20 and Wang et al.21.
1wt. %HCL18. Volume fractions of the lower bainite were Figure 2 shows typical scanning electron micrographs
determined by clemex vision image analysis software based of the mixed lower bainite - martensite microstructures
on the difference in color between lower bainite (dark) and after austenitizing at 910°C - 1200°C. It is evident that by
martensite (white). At least 5 representative areas in each increasing austenitizing temperature both thickness and
sample were studied through metallographic evaluations. length of the bainite sheaves were increased. The variation
The X-Ray diffraction technique was employed by using of microstructural factors as a function of austenitizing
CuKα radiation to detect retained austenite19. The fracture temperature were quantitatively established and shown in

Figure 1. The lower bainite - martensite mixed microstructure, austenitized at 910°C (a) optical and (b) Scanning electron (SEM) micrographs.
 Effect of Austenitizing Temperature on Mechanical Properties of the Mixed Bainite - Martensite 3
Microstructure in CrMoV Steel

figure 3. As expected, during the austenitizing process, the prior 3.2. Mechanical properties
austenite grain size increased with increasing austenitizing
temperature, for example about 18µm at 910°C and nearly In order to study the effect of lower bainite - martensite
235µm at 1200°C. Also the bainite length and width was mixed microstructure on the mechanical properties of the
increased in the range of 16-115µm and 2.5-9µm for samples CrMoV steel, tensile and impact tests were conducted. The
austenitized at 910°C to 1200°C, in which the average error tensile and impact specimens were contained 0 (a fully
for grain size, bainite length and bainite wedth are ±3 µm, martensitic microstructure), 12, 28, 37, 41, 43, 45, 49, 75
±2µm and ±1µm, respectively. and 100 (a fully bainitic microstructure) volume pct lower
Chakraborty et al.22 reported that refinement of the austenite bainite. Variations of yield and tensile strength in terms of the
grains led to enhancement of the heterogeneous nucleation lower bainite volume fraction are shown in figures 4 and 5,
rate of bainite but the extent of the overall transformation in which the average error for yield and ultimate tensile
was limited by a slow growth rate. In other words, lowering strengths are ±10 MPa and ±15 MPa, respectively. According
of the prior austenite grain size may generate additional to the rule of mixtures (equation 1), yield strength of mixed
nucleation sites for bainite and enhance nucleation rate, but lower bainite - martensite microstructure decreases linearly
restrict the growth of ferritic sheaves by grain boundaries. with the increase in the volume fraction of lower bainite,
They have suggested that the growth of bainite is retarded because the yield strength of martensite microstructure is
when austenite grains are finer22. Therefore as shown in Fig.2, higher than the yield strength of bainite microstructure5.
the bainite width increased by increasing the austenitizing
temperature. v yMix = v yM Q1 - VBV + v y BVB
(1)

Figure 2. Scanning electron (SEM) micrographs of mixed lower bainite - martensite microstructures, austenitized at (a) 910°C (b) 1000°C
(c) 1100°C (d) 1200°C.
4 Abbaszadeh et al. Materials Research

the yield strength of the samples austenitized at 910°C and

1000°C increases and attains about 1869MPa and 1807MPa,
respectively and then decreases to the strength level of a
fully lower bainitic samples.
As seen in Fig.1, the formation of lower bainite
partitions the prior austenite grains and therefore, decreases
the martensite packet sizes. According to the Hall - petch
relationship, equation (2), decreasing the martensite packet
size increases the strength of the martensite microstructure.

v y M = v i + kS m -0.5 (2)

Where σyM is yield strength of martensite in the mixed

microstructure, σi is frictional stress, k is constant, and Sm
Figure 3. Variation of microstructural factors as a function of is the distance between the initial grain boundary and the
austenitizing temperature. second phase, e.g. the martensite packet size12. In addition
the strength of lower bainite in mixed microstructure was
increased by plastic constraint induced by the surrounding
stronger martensite. Yong and Behadeshia23 demonstrated
that the yield strength is increased by plastic constraint, upon
which a soft thin layer can be constrained by the hard matrix
surrounding it. For example a weak brazing alloy can be
used effectively to bond much stronger specimens provided
that the brazing material is thin enough to be constrained by
the surrounding stronger matrix. Indeed the strength of the
joint increases as the thickness of the brazing layer decreases.
The same phenomenon occurs when the lower bainite plates
form in the austenite which subsequently transforms to much
stronger martensite. In other words the bainite plate plays the
role of soft layer. On the other word, the presence of a peak
Figure 4. Variation of yield strength with amount of the lower
at about 28 vol. % lower bainite in the curve of strength as a
bainite for various austenitizing temperatures.
function of lower bainite volume fraction can be attributed
to the improvement in the strength of martensite due to the
refinement of its substructure that is caused by partitioning of
the prior austenite grains by the lower bainite. In addition the
strength of lower bainite was increased by plastic constraint
induced by the martensite. However this is not the case for
the samples austenitized at temperatures higher than 1000°C.
Decreasing the mechanical properties with the increase of the
austenitizing temperature may be attributed to the formation
of coarser prior austenite grains as shown in fig.3, and in turn,
formation of coarser martensite packets. However increasing
the austenitizing temperature from 1100°C - 1200°C causes
yield and tensile strength of the mixed microstructure of
lower bainite - martensite to become less than the martesitic
Figure 5. Variation of tensile strength with amount of the lower microstructure. As explained in section 3.1, increasing the
bainite for various austenitizing temperatures.
austenitizing temperature causes increase in bainite width.
According to Eq.3, increasing the bainite width (L3) decreases
Where σyMix is yield strength of lower bainite - martensite the yield and tensile strength of the mixed microstructure of
mixed microstructure, σyM and σyB are yield strength of lower bainite - martensite in comparison with the single phase
martensite and lower bainite microstructure, respectively. martensite microstructure22,24.
On comparison, in the present experimental results, σyMix
deviates more from equation 1. As shown in Fig 4, by v Fe + v C + / v ss + K1 Q L3V-1 + K2 t1d/2 + K3 D -1 (3)
v =
increasing the volume fraction of lower bainite up to 28%,
 Effect of Austenitizing Temperature on Mechanical Properties of the Mixed Bainite - Martensite 5
Microstructure in CrMoV Steel

where σFe is the strength of pure annealed iron, σC is the lower bainite is formed through an isothermal transformation.
contribution of solid solution strengthening due to carbon, The mixed microstructures of bainite - martensite formed by
ΣσSS is the summation of solid solution strengthening due to continious cooling and slack quenching have lower toughness
all substitutional solutes, L3 is the ferrite plate thickness, ρd is than martensitic microstructures8. Howevre, by increasing
the dislocation density, Δ is the distance between the carbide the austenitizing temperature in the range 910°C - 1200°C,
particles (or precipitates) and K1, K2, K3 are constants22,24. elongation, reduction of area and charpy impact energy decreases
The variations of elongation, reduction of area and charpy for all microstructures. Since this decrease is observed for all
impact energy with austenitizing temperature for various microstructures, it is expected that the austenite grain size
microstructures obtained from different heat treatment cycles is primarily responsible for controlling ductility and impact
are shown in figures 6 - 8, respectively. As shown, at constant toughness due to variation in austenitizing temperature26.
austenitizing temperature, ductility and impact toughness
increased by increasing the lower bainite volume fraction. This
improvement in ductility and impact toughness is not because
of retained austenite. X-Ray difraction patterns have not shown
difraction peaks at (200)γ, (220)γ, (113)γ, (222)γ, (004)γ. As
these peaks were not found in XRD patterns of specimens,
it is speculated that the amount of retained austenite was not
sufficient enough to be detected19. Thus, this amount of retained
austenite has no significant effect on the mechanical properties
of various microstructures. Thus, the tensile and impact tests
show that lower bainite is more ductile and tougher than
martensite microstructure. On the other hand, in mixed lower
bainite - martensite microstructure, a crack propagated within Figure 6. Influence of amount of the lower bainite on elongation
the martensite will be blunt when reaching the more flexible of specimens austenitized at different temperatures.
lower bainite plates and therefore the impact energy increases.
This is because lower bainite brings into full play the arresting
effect of the crack and stress - relief, as a result of deformation
in association with martensite. From Figure 9 microcracks
are found behind the fracture surfaces of impact specimens
having mixed lower bainite - martensite microstructure. It can
be seen from Figure 9a and 9b microcracks stoped by dimple
rigions (lower bainite area). This suggests that lower bainite
is responsible for the increased impact toughness. Typical
SEM images of the impact fracture surface of samples after
austenitized at 910°C are shown in Figure 10a - 10e. Figure
10a reveals that a crack in martensitic samples propegated
in a brittle manner, producing cleavage and quasi- cleavage
Figure 7. Influence of amount of the lower bainite on reduction
facets. The results are consistent with low impact toyghness area of specimens austenitized at different temperatures.
of martensitic samples. The impact fracture morfology in
mixed lower bainite - martensite microstructure samples
was a mixed mode of dimple rupture and quasi - cleavage.
However, by increasing the lower bainite volume fraction
(Fig.10b - Fig.10d), the samples exhibited more dimple
rupture. On the other hand, the fracture morphology change
from mixed mode of dimple rupture and quasi - cleavage in
mixed microstructure samples (Fig.10b - Fig.10d) to fully
dimple rupture in fully lower bainitic sample (Fig.10e).
Therefore, as shown in Fig.8, by incresing the lower bainite
volume fraction, the impact toughness is increaesed. Also,
the fully lower bainitic sample has higher impact absorbed
energy than the othere samples. The superior impact toughness
and ductility of the lower bainite compared with martensite
in Q&T condition samples were also found in the earlier Figure 8. Variation of charpy V - notch impact energy with amount
studies25. But, it is noteworthy that this is only observed when of the lower bainite for various austenitizing temperatures.
6 Abbaszadeh et al. Materials Research

Figure 9. Scanning electron micrograph (SEM) of microcrack being initiated during charpy impact testing of specimen having 49%
lower bainite.

Figure 10. Scanning electron micrograph (SEM) of impact fracture surface showing (a) transgranular
cleavage and quasi - cleavage in martensitic sample, (b) mostly quasi - cleavage and some dimple
rupture in mixed 12% lower bainite - martensite microstructure, (c) quasi - cleavage and dimple
rupture in mixed 28% lower bainite - martensite microstructure, (d) mostly dimple rupture and
some quasi - cleavage facets in mixed 49% lower bainite - martensite, (e) dimple rupture in fully
lower bainitic sample.
 Effect of Austenitizing Temperature on Mechanical Properties of the Mixed Bainite - Martensite 7
Microstructure in CrMoV Steel

4. Conclusions 6. Rastegari H, Kermanpur A, Najafizadeh A. Investigating the

effects of short time austenitizing and cooling rate on pearlitic
microstructure and mechanical properties of a hot rolled pain
1. A maximum point was observed in the curve of
eutectoid carbon steel. Materials & Design. 2015;67:217-223.
strength as a function of the lower bainite. This can be
explained on the basis of two factors. The first is an 7. Li Y, Chen X. Microstructure and mechanical properties of
increase in the strength due to the partitioning of the austempered high silicon cast steel. Materials Science and
Engineering: A. 2001;308(1-2):277-282.
prior austenite grains by the lower bainite resulting
in the refinement of martensite substructures. The 8. Zhang XZ, Knott JF. Cleavage fracture in bainitic and martensitic
second is a plastic constraint effect leading to an microstructure. Acta Materialia. 1999;47(12):3483-3495.
enhanced strength of the lower bainite induced by 9. Salemi A, Abdollah-Zadeh A, Mirzaei M, Assadi H. A study on
the surrounding relatively rigid martensite. fracture properties of multiphase microstructures of CrMo steel.
Materials Science and Engineering: A. 2008;492(1-2):45-48.
2. By increasing the volume fraction of lower bainite,
the elongation, reduction area and charpy V - notch 10. Abdollah-Zadeh A, Salemi A, Assadi H. Mechanical behavior
impact energy increased for all austenitizing of CrMo steel with tempered martensite and ferrite-bainite-
martensite microstructure. Materials Science and Engineering:
temperature because of significantly greater ductility
A. 2008;483-484:325-328.
and impact toughness of lower bainite compared
with martensite. 11. Tomita Y. Improved lower temperature fracture toughness of
3. The impact fracture surface of martensitic and lower ultrahigh strength 4340 steel through modified heat treatment.
Metallurgical Transactions A. 1987;18(8):1495-1501.
bainitic samples exhibited cleavage and dimple
rupture, respectively. However the fracture morfology 12. Tomita Y, Okabayashi K. Improvement in lower temperature
in mixed lower bainite - martensite microstructure mechanical properties of 0.40 pct C-Ni-Cr-Mo ultrahigh
strength steel with the second phase lower bainite. Metallurgical
samples was a mixed mode of dimple rupture and
Transactions A. 1983;14(2):485-492.
qusi - cleavage.
4. By increasing austenitizing temperature from 1000°C 13. Tomita Y, Okabayashi K. Heat treatment for improvement
to 1200°C (40min), the YS, UTS, %EL and CVN in lower temperature mechanical properties of 0.4 pct C- Cr-
Mo ultrahigh strength steel. Metallurgical Transactions A.
impact energy decreases for all samples and no
1983;14(11):2387-2393.
peak is observed in the curve of the strength as a
function of the lower bainite volume fraction for 14. Tomita Y, Okabayashi K. Modified heat treatment for lower
samples austenitized at high temperature (1100°C temperature improvement of the mechanical properties of two
ultrahigh strength low alloy steels. Metallurgical Transactions
- 1200°C). This is attributed mainly to the increase
A. 1985;16(1):83-91.
in austenite grain size and width of bainite sheaves.
15. Rao TVLN, Dikshit SN, Malakondaiah G, Rao PR. On mixed
5. References upper bainite-martensite in an AISI 4330 steel exhibiting an
uncommonly improved strength-toughness combination. Scripta
Metallurgica et Materialia. 1990;24(7):1323-1328.
1. Chang TL, Tsay LW, Chen C. Influence of gaseous hydrogen
on the notched tensile strength of D6ac steel. Materials Science 16. ASTM E8 - Test Method for Tension Testing of Metallic
and Engineering: A. 2001;316(1-2):153-160. Material. In: Annual Book of ASTM Standards. Philadelphia:
ASTM International; 1998.
2. Varshney A, Sangal S, Kundu S, Mondul K. Super strong and
highly ductile low alloy multiphase steel consisting of bainite, 17. ASTM E23 - Test Method for Notched Bar Impact Testing
ferrite and retained austenite. Materials & Design. 2016;95:75- of Metallic Material. In: Annual Book of ASTM Standards.
88. Philadelphia: ASTM International; 1998.

3. Huang W, Liu W, Huang Y, Chen H, Huang W. Effect of a 18. Bramfitt BL, Benscoter A. Metallographer's Guide: Practices
quenching-long partitioning treatment on the microstructure and Procedures for Iron and Steels. Materials Park: ASM
and mechanical properties of a 0.2C% bainitic steel. Journal International; 2002.
of Materials Processing Technology. 2015;222:181-187.
19. Magner SH, de Angelis RJ, Weins WN, Makinson JD. A
4. Zhao J, Zhao T, Hou CS, Zhang FC, Wang TS. Improving historical review of retained austenite and its measurement by
impact toughness of high-C-Cr bearing steel by Si-Mo alloying X-ray diffraction. Advances in X-ray Analysis. 2002;45:92-97.
and low-temperature austempering. Materials & Design.
20. Wen J, Li Q, Long Y. Effect of austempering on microstructure
2015;86:215-220.
and mechanical properties of GCr18Mo steel. Materials Science
and Engineering: A. 2006;438-440:251-253.
5. Baradari S, Boutorabi SM. Effects of isothermal transformation
conditions on the microstructure and hardness values of a high- 21. Wang TS, Yang J, Shang CJ, Li XY, Zhang B, Zhang FC.
carbon Al-Si alloyed steel. Materials & Design. 2015;86:603- Microstructures and impact toughness of low-alloy high-carbon
609. steel austempered at low temperature. Scripta Materialia.
2009;61(4):434-437.
8 Abbaszadeh et al. Materials Research

22. Chakraborty J, Bhattacharjee D, Manna I. Development of

ultrafine bainite + martensite duplex microstructure in SAE 25. Tartaglia JM, Lazzari KA, Hui GP, Hayrynen KL. A Comparison
52100 bearing steel by prior cold deformation. Scripta Materialia. of Mechanical Properties And Hydrogen Embrittlement Resistance
2009;61(6):604-607. of Austempered vs Quenched and Tempered 4340 Steel.
Metallurgical and Materials Transactions A. 2008;39(3):559-
23. Yong CH, Bhadeshia HKDH. Strength of mixtures of bainite and 576.
martensite. Materials Science and Technology. 1994;10(3):209-
214.
26. Kishore Babu N, Suresh MR, Sinha PP, Sarma DS. Effect of
24. Chakraborty J, Bhattacharjee D, Manna I. Austempering of austenitizing temperature and cooling rate on the structure and
bearing steel for improved mechanical properties. Scripta properties of an ultrahigh strength low alloy steel. Journal of
Materialia. 2009;59(2):247-250. Materials Science. 2006;41(10):2971-2980.