Lecture#3

‫ قسم الهندسة الميكانيكية‬/ ‫ كلية الهندسة‬/ ‫جامعة الموصل‬
Department of Mechanical
Engineering
Subject: Internal Combustion Engines

The Fuel-Air Cycles
Class: M. Sc. / Thermal Power
Lecturer Dr. Abdulrahman Habbo Mohammed Dr. Ahmed Fouad Al-Neama
The Fuel-Air Cycles

Introduction:
The basic problem in the air-cycle analysis is that it is based on highly simplified
approximations. This is why the results obtained from such analysis are much greater
than the actual performance. For example, an engine with r = 7 has a thermal efficiency
(based on air cycle analysis) equals to 54% while the actual value does not exceed
30%. This is mainly due to the following reasons:
1. Non-instantaneous burning of the fuel.
2. Non-instantaneous operation of the valves.
3. Over simplifications in using the values of the properties of the working fluids.
4. Incomplete combustion of the fuel.
5. Assuming constant specific heat of the working fluid.
6. Assuming the working fluid to be only air.
Fuel-Air cycle: is defined as the theoretical cycle that is based on the actual properties
of cylinder gases.
Fuel-Air cycle approximation:
1. The variation in specific heat of gases with temperature (i.e. C p and Cv are not
constant).
2. The fact that the fuel and air do not completely combine chemically at high
temperature.
abidhabbo20@uomosul.edu.iq :‫عنوان البريد االلكتروني‬ ‫ عبدالرحمن حبو محمد الحبو‬.‫د‬.‫م‬.‫ أ‬:‫اسم التدريسي‬
ahmedfalneama@uomosul.edu.iq ‫ أحمد فؤاد محمود النعمة‬.‫د‬.‫م‬
Page | 22
3. No change in the fuel or air chemical composition before combustion.
4. The variations in the number of molecules present in the cylinder as the
temperature and pressure change (dissociation). The working fluid in a thermal
equilibrium.
Fuel-Air Cycle Assumptions:

The following assumption are considered when dealing with fuel-air cycles
calculations:
1. Fuel is completely vaporized and perfectly mixed with air.
2. Combustion take place at top dead center, i.e. highly idealized.
3. Assume no heat exchange occurs between the gases and cylinder walls.
4. Compression and expansion process are reversible and charge transfer happen
but transfer work may be ignored.
DEFINITIONS:
Approximate method of fuel-air cycle calculation:
If the fuel-air ratio is 𝐹, then for 1 kg of air will be (1 + 𝐹) kg of products formed. This
(1 + 𝐹) kg of combustion products at P1 and T4 undergoes blow down process from P4
to Pexh at constant volume V1 (T4 = constant). Fraction of this combustion products
would be left in the engine cylinder, its volume equal to the clearance volume V 2 and
its temperature is T4 and it is called residual gas and may be expressed as residual
gas fraction 𝑓.
The following definitions are very important to be able to analyse the fuel-air cycle and
for their calculations.
1. Fresh air (𝑚𝑎𝑖𝑟 ): which is the fresh mass of air admitted to the cylinder engine
for each cycle.
𝑚𝑎𝑖𝑟 = 1 − 𝑓 (1 )
2. Fresh fuel (𝑚𝑓 ): may be defined as the new mass of fuel supplied to the cylinder
for each cycle.
𝑚𝑓 = (1 − 𝑓)𝐹 (2 )
where 𝐹 is the fuel-air ratio
𝑚𝑎𝑠𝑠 𝑜𝑓 𝑓𝑢𝑒𝑙
𝐹=
𝑚𝑎𝑠𝑠 𝑜𝑓 𝑎𝑖𝑟
Page | 23
𝑓: is the residual gas fraction, and may be defined as the ratio of mass fraction
remained in an engine cylinder from the previous cycle to the total mixture.
3. Total charge (𝑚𝑡 ): is the total contents of cylinder at any time of the cycle.
𝑚𝑡 = 𝑚𝑎𝑖𝑟 + 𝑚𝑓 + 𝑚𝑟 (3 )
where 𝑚𝑟 is the residual mass
𝑚𝑟
𝑓=
𝑚𝑡
4. Fresh mixture (𝑚𝑖 ): this may be defined according to the type of engine, spark
ignition engine or compression ignition engine.
For spark ignition engines (or carburetted engines), 𝑚𝑖 can be obtained as follows:
𝑚𝑖 = 𝑚𝑎𝑖𝑟 + 𝑚𝑓 (4)
For compression ignition engines (or injection engines), 𝑚𝑖 can be calculated as:
𝑚𝑖 = 𝑚𝑎𝑖𝑟 (5)
Finally, the masses can be summarized as follows:
𝑚𝑎𝑖𝑟 = 1 − 𝑓
𝑚𝑓 = (1 − 𝑓)𝐹
𝑚𝑟 = (1 + 𝐹 )𝑓
𝑚𝑡 = 1 + 𝐹
and 𝑚𝑡 = 𝑚𝑎𝑖𝑟 + 𝑚𝑓 + 𝑚𝑟 at any time of the cycle
Page | 24
Calculation of Residual Gas Fraction ( 𝒇):
The calculation of residual gas fraction ( 𝑓) simply can be calculated by using the
general law of perfect gas at points “o” and “4” as shown in Fig. (1).
For point 4:
𝑃4 𝑉1 = 𝑚4 𝑅𝑇4 [𝑚4 = 𝑚𝑡 & 𝑅 = 𝑅𝑃 ]
𝑃4 𝑉1 = (1 + 𝐹 )𝑅𝑃 𝑇4 (1)
For point o:
𝑃𝑒𝑥ℎ 𝑉2 = 𝑚𝑟 𝑅𝑇4
𝑃𝑒𝑥ℎ 𝑉2 = (1 + 𝐹 )𝑓𝑅𝑃 𝑇4 (2)
Divide Eqs. (1) and (2), we get:
𝑃𝑒𝑥ℎ 𝑉2 (1 + 𝐹 )𝑓
× =
𝑃4 𝑉1 1+𝐹
which gives:
𝑃𝑒𝑥ℎ 1
× =𝑓
𝑃4 𝑟
Fig. 1: P – V diagram of Otto cycle.
Page | 25
Calculation of Trapped Temperature (T1):
In order to calculate the trapped temperature (T1) at state 1 before the compression
process begin, two kinds of cycles are available:
1. Constant volume cycle.
2. Constant pressure cycle.
1- Constant volume cycle:

In this cycle the total mass can be obtained as follows:
𝑚𝑡 = 𝑚𝑚 = 𝑚𝑎𝑖𝑟 + 𝑚𝑓 + 𝑚𝑟
where 𝑚𝑚 is the mass of total mixture. However, the trapped temperature obviously
can be obtained from the enthalpy balance as:
𝐻𝑚 = ∑ 𝐻𝑖 = 𝐻𝑎𝑖𝑟 + 𝐻𝑓 + 𝐻𝑟
where 𝐻𝑚 is the enthalpy of the mixture in the cylinder at state 1

𝐴𝑛𝑑 𝐻𝑚 = 𝑚𝑚 𝐶𝑃𝑚 (𝑇1 − 273)
𝐻𝑎𝑖𝑟 = 𝑚𝑎𝑖𝑟 𝐶𝑃𝑎𝑖𝑟 (𝑇𝑎𝑖𝑟 − 273)
𝐻𝑓 = 𝑚𝑓 𝐶𝑃𝑓 (𝑇𝑓 − 273)
𝐻𝑟 = 𝑚𝑟 𝐶𝑃𝑃 (𝑇𝑒𝑥ℎ − 273)

Which can be written as follows:
𝑚𝑚 𝐶𝑃𝑚 (𝑇1 − 273) = 𝑚𝑎𝑖𝑟 𝐶𝑃𝑎𝑖𝑟 (𝑇𝑎𝑖𝑟 − 273) + 𝑚𝑓 𝐶𝑃𝑓 (𝑇𝑓 − 273) + 𝑚𝑟 𝐶𝑃𝑃 (𝑇𝑒𝑥ℎ − 273)
Referring to constant volume cycle, the enthalpy of fuel 𝐻𝑓 depend on the condition of
the fuel supply at entry, gas or liquid.
1- If the fuel is gas, the 𝐻𝑓 can be obtained as follows:
𝐻𝑓 = 𝑚𝑓 (𝐶𝑃𝑓 ) (𝑇𝑓 − 273)

𝑔
2- If the fuel is liquid, then the enthalpy of fuel depends on the fuel temperature
because the latent heat of evaporation is involved, (i.e. ℎ𝑓𝑔 is available at 25 ºC).
Three cases can be present:
• Case 1: if the temperature of fuel is less than 25 ºC (𝑇𝑓 < 25 ºC), hence 𝐻𝑓
𝐻𝑓 = 𝑚𝑓 [(𝐶𝑃𝑓 ) (𝑇𝑓 − 273) + (𝐶𝑃𝑓 ) (298 − 𝑇𝑓 ) − (ℎ𝑓𝑔 ) ]

𝐿 𝐿 25
Page | 26
• Case 2: if the temperature of fuel is equal 25 ºC (𝑇𝑓 = 25 ºC), hence 𝐻𝑓
𝐻𝑓 = 𝑚𝑓 [(𝐶𝑃𝑓 ) (298 − 273) − (ℎ𝑓𝑔 ) ]

𝐿 25
• Case 3: if the temperature of fuel is higher than 25 ºC (𝑇𝑓 > 25 ºC), hence 𝐻𝑓
𝐻𝑓 = 𝑚𝑓 [(𝐶𝑃𝑓 ) (298 − 273) + (𝐶𝑃𝑓 ) (𝑇𝑓 − 298) − (ℎ𝑓𝑔 ) ]

𝐿 𝑔 25
2. Constant pressure cycle:

Clearly, this is the typical cycle applied for compression ignition engines. At state 1 as
shown in Fig. (2), the total mass (𝑚𝑡 ) can be obtained as follows:
𝑚𝑡 = 𝑚𝑚 = 𝑚𝑎𝑖𝑟 + 𝑚𝑟
Fig. 2: P – V diagram of Diesel cycle.
However, the trapped temperature 𝑇1 also can be calculated in similar manner by

introducing the enthalpy balance:
𝐻𝑚 = ∑ 𝐻𝑖 = 𝐻𝑎𝑖𝑟 + 𝐻𝑟
Or can be written as:

𝑚𝑚 𝐶𝑃𝑚 (𝑇1 − 273) = 𝑚𝑎𝑖𝑟 𝐶𝑃𝑎𝑖𝑟 (𝑇𝑎𝑖𝑟 − 273) + 𝑚𝑟 𝐶𝑃𝑃 (𝑇𝑒𝑥ℎ − 273)
Page | 27
Example 1:
In a constant volume fuel-air cycle with a compression ratio of 9. The mixture
has fuel-air ratio of 0.0785. Fuel is C8H17 of lower calorific value of 44100 kJ/kg.
Mixture pressure and temperature at the beginning of compression is 0.96 bar
and 328 K. Calculate the thermal efficiency, indicated specific fuel consumption
and mean effective pressure.
Assuming residual gas fraction is 0.03, specific heat of gases at average
temperature of 2800 K, and dropping in temperature due to dissociation is 10%.
Also assume incomplete combustion which gives CO and H 2 in products as
𝑛𝐶𝑂 𝑛𝐻2
= 𝟎. 𝟑 and = 𝟎. 𝟏𝟒, relative to CO2 and H2O of complete combustion,
𝑛𝐶𝑂2 𝑛𝐻2 𝑂
and take the index of expansion and compression of (𝛾 = 𝟏. 𝟑).
Example 2:
A constant volume fuel-air cycle of compression ratio of 7, operates on a
hydrocarbon fuel of C8H17. The engine is running at 120% theoretical of air. The
ambient condition is 1.01 bar and 30 ºC. The temperature and pressure before
the exhaust valve opened are 5 bar and 1100 K respectively. Calculate the
maximum temperature in the cycle, the thermal efficiency and mean effective
pressure taking into account the following data:
For reactants: M = 28.5 and Cp = 1.45 kJ/kg.K
For products: M = 30.5 and Cp = 1.15 kJ/kg.K
LCV = 40000 kJ/kg, Tf = 20 ºC and Cpf =1.8 kJ/kg.K.
Example 3:
A constant pressure fuel-air cycle of a compression ratio of 16. The ambient
conditions are 1.0 bar and 25 ºC. The fuel air ratio is given as 0.075, the residual
gas fraction is 5%. If the pressure at the end of expansion stroke is 6 bar and the
exhaust temperature is 1000 K, calculate the cut-off ratio and thermal efficiency
of the cycle if the lower calorific value is 42000 kJ/kg. Assume:
For reactants: M = 28
For products: M = 30 and Cp = 1.2 kJ/kg.K
Page | 28
Home Work:
Q1.
A spark ignition engine of a compression ratio of 8, operates with stoichiometric
fuel-air ratio of hydrocarbon fuel of C8H18. The pressure and temperature inside
the cylinder at the start of compression are 1 atmosphere and 350 K respectively.
Find the temperature and pressure per unit mass of air at the end of compression
stroke. Also find the maximum temperature and pressure in the cycle and
thermal efficiency, assuming the residual gas fraction is 0.08 and the exhaust
temperature is 1800 K.
(Note: LCV = 44300 kJ/kg and 𝐶𝑃𝑓 = 1.979 kJ/kg.K).
Page | 29

Lecture#3

Uploaded by

Copyright:

Available Formats

Lecture#3

Uploaded by

Document Information

Copyright

Available Formats

Share this document

Share or Embed Document

Sharing Options

Did you find this document useful?

Is this content inappropriate?

Copyright:

Available Formats

Lecture#3

Uploaded by

Copyright:

Available Formats

‫ قسم الهندسة الميكانيكية‬/ ‫ كلية الهندسة‬/ ‫جامعة الموصل‬

Subject: Internal Combustion Engines

The Fuel-Air Cycles

Fuel-Air Cycle Assumptions:

Fig. 1: P – V diagram of Otto cycle.

1- Constant volume cycle:

where 𝐻𝑚 is the enthalpy of the mixture in the cylinder at state 1

𝐻𝑓 = 𝑚𝑓 𝐶𝑃𝑓 (𝑇𝑓 − 273)

𝐻𝑟 = 𝑚𝑟 𝐶𝑃𝑃 (𝑇𝑒𝑥ℎ − 273)

𝐻𝑓 = 𝑚𝑓 (𝐶𝑃𝑓 ) (𝑇𝑓 − 273)

𝐻𝑓 = 𝑚𝑓 [(𝐶𝑃𝑓 ) (𝑇𝑓 − 273) + (𝐶𝑃𝑓 ) (298 − 𝑇𝑓 ) − (ℎ𝑓𝑔 ) ]

𝐻𝑓 = 𝑚𝑓 [(𝐶𝑃𝑓 ) (298 − 273) − (ℎ𝑓𝑔 ) ]

𝐻𝑓 = 𝑚𝑓 [(𝐶𝑃𝑓 ) (298 − 273) + (𝐶𝑃𝑓 ) (𝑇𝑓 − 298) − (ℎ𝑓𝑔 ) ]

2. Constant pressure cycle:

Fig. 2: P – V diagram of Diesel cycle.

However, the trapped temperature 𝑇1 also can be calculated in similar manner by

Or can be written as:

You might also like