NCP1050, NCP1051,

NCP1052, NCP1053,
NCP1054, NCP1055

Monolithic High Voltage

Gated Oscillator Power
Switching Regulator http://onsemi.com

The NCP1050 through NCP1055 are monolithic high voltage

MARKING
regulators that enable end product equipment to be compliant with low DIAGRAMS
standby power requirements. This device series combines the required
converter functions allowing a simple and economical power system 8
solution for office automation, consumer, and industrial products.
PDIP−8 NCP105XZ
These devices are designed to operate directly from a rectified AC line P SUFFIX
8 AWL
source. In flyback converter applications they are capable of providing CASE 626A YYWWG
an output power that ranges from 6.0 W to 40 W with a fixed AC input
1
of 100 V, 115 V, or 230 V, and 3.0 W to 20 W with a variable AC input 1
Pin: 1. VCC
that ranges from 85 V to 265 V. 2. Control Input
This device series features an active startup regulator circuit that 3, 7−8. Ground
eliminates the need for an auxiliary bias winding on the converter 4. No Connection
5. Power Switch Drain
transformer, fault detector and a programmable timer for converter
overload protection, unique gated oscillator configuration for extremely
fast loop response with double pulse suppression, power switch current
limiting, input undervoltage lockout with hysteresis, thermal shutdown,
and auto restart fault detection. These devices are available in SOT−223
AWW
economical 8−pin dual−in−line and 4−pin SOT−223 packages. ST SUFFIX N5XZG
CASE 318E G
Features 1
• Startup Circuit Eliminates the Need for Transformer Auxiliary Bias Pin: 1.VCC
2.Control Input
Winding 3.Power Switch Drain
• Optional Auxiliary Bias Winding Override for Lowest Standby 4.Ground
Power Applications
• Converter Output Overload and Open Loop Protection
• Auto Restart Fault Protection
X = Current Limit (0, 1, 2, 3, 4, 5)
• IC Thermal Fault Protection Z = Oscillator Frequency
• Unique, Dual Edge, Gated Oscillator Configuration for Extremely A = 44 kHz, B = 100 kHz, C = 136 kHz
Fast Loop Response A = Assembly Location
WL, L = Wafer Lot
• Oscillator Frequency Dithering with Controlled Slew Rate Driver for YY, Y = Year
Reduced EMI WW, W = Work Week
• Low Power Consumption Allowing European Blue Angel Compliance G or G = Pb−Free Package
(Note: Microdot may be in either location)
• On−Chip 700 V Power Switch Circuit and Active Startup Circuit
• Rectified AC Line Source Operation from 85 V to 265 V
ORDERING INFORMATION
• Input Undervoltage Lockout with Hysteresis See detailed ordering and shipping information on page 22 of
• Oscillator Frequency Options of 44 kHz, 100 kHz, 136 kHz this data sheet.

• Pb−Free Packages are Available

Typical Applications
• AC−DC Converters
• Wall Adapters
• Portable Electronic Chargers
• Low Power Standby and Keep−Alive Supplies

© Semiconductor Components Industries, LLC, 2006 1 Publication Order Number:

February, 2006 − Rev. 9 NCP1050/D
 NCP1050, NCP1051, NCP1052, NCP1053, NCP1054, NCP1055

+
AC Line + Snubber +
Input Converter
DC Output

−
Power Switch Circuit Output 5

VCC
Startup & VCC
+ Regulator Circuit
1
Power
Fault Detector Switch
Circuit
Control Input 2 Oscillator &
Gating Logic

Ground 3, 7−8

Figure 1. Typical Application

Pin Function Description

Pin Pin
(SOT−223) (PDIP−8) Function Description
1 1 VCC This is the positive supply voltage input. During startup, power is supplied to this input
from Pin 5. When VCC reaches VCC(on), the Startup Circuit turns off and the output is
allowed to begin switching with 1.0 V hysteresis on the VCC pin. The capacitance con-
nected to this pin programs fault timing and frequency modulation rate.
2 2 Control Input The Power Switch Circuit is turned off when a current greater than approximately 50 A
is drawn out of or applied to this pin. A 10 V clamp is built onto the chip to protect the
device from ESD damage or overvoltage conditions.
4 3, 7, 8 Ground This pin is the control circuit and Power Switch Circuit ground. It is part of the integrated
circuit lead frame.

− 4 No Connection
3 5 Power Switch This pin is designed to directly drive the converter transformer primary, and internally
Drain connects to Power Switch and Startup Circuit.

http://onsemi.com
2
 NCP1050, NCP1051, NCP1052, NCP1053, NCP1054, NCP1055

+
AC Line + Snubber +
Input Converter
DC Output

Power Switch Circuit Output

VCC Startup
Circuit
+ Startup/V CC Reg
10 V
+
− Fault Internal
+ Detector Bias
VCC Bypass/ 7.5/8.5 V
Fault Timing/ Fault
VCO Sweep S Latch
Undervoltage Thermal Power
Control Switch
Lockout Shutdown Q Circuit
−
+ R Driver
+
4.5 V
VCC
Oscillator
IH = 10 A Turn On
48 A
Latch
Turn Off
R Latch

Q Ck
+
2.6 V S Q
Control
Input R

10 V Leading Edge
+
+ Blanking
−
3.3 V Current Limit +
Comparator

RSENSE
IH = 10 A
48 A

Ground

Figure 2. Representative Block Diagram

http://onsemi.com
3
 NCP1050, NCP1051, NCP1052, NCP1053, NCP1054, NCP1055

fOSC (high)
8.5 V

VCC fOSC (low)

7.5 V

Oscillator Duty
Cycle

Oscillator Clock

47.5 A
37.5 A
ICONTROL, SINK
0 A

Leading Edge On Leading Edge On

Feedback Off Duty Cycle Off
Leading Edge On Leading Edge On
Duty Cycle Off Delay On No Second Current Limit Off
Duty Cycle Off Pulse

Power Switch
Circuit Gate Drive

Current Limit
Threshold
Primary Current

Current Limit
Propagation
Delay

Figure 3. Timing Diagram for Gated Oscillator with Dual Edge PWM

http://onsemi.com
4
 NCP1050, NCP1051, NCP1052, NCP1053, NCP1054, NCP1055

ICC1, Current Measurement

ICC2, Current Measurement

VCC(on)
Hysteretic Regulation
VCC(off)
VCC
VCC(reset)
ICC3, Current Measurement

0V
6.3 mA
I(start)

0 mA

ICC1
ICC2
ICC
ICC3

0 mA

I(start)

47.5 A
37.5 A
ICONTROL, SINK
0 A

V(pin 5)

Fault Applied Fault Removed

Figure 4. Non−Latching Fault Condition Timing Diagram

http://onsemi.com
5
 NCP1050, NCP1051, NCP1052, NCP1053, NCP1054, NCP1055

MAXIMUM RATINGS
Rating Symbol Value Unit
Power Switch and Startup Circuit
Drain Voltage Range VDS *0.3 to 700 V
Drain Current Peak During Transformer Saturation IDS(pk) 2.0 Ilim Max A
Power Supply/VCC Bypass and Control Input
Voltage Range VIR *0.3 to 10 V
Current Imax 100 mA
Thermal Characteristics °C/W
P Suffix, Plastic Package Case 626A−01
Junction−to−Lead RJL 9.0
Junction−to−Air, 2.0 Oz. Printed Circuit Copper Clad RJA
0.36 Sq. Inch 77
1.0 Sq. Inch 60
ST Suffix, Plastic Package Case 318E−04
Junction−to−Lead RJL 14
Junction−to−Air, 2.0 Oz. Printed Circuit Copper Clad RJA
0.36 Sq. Inch 74
1.0 Sq. Inch 55
Operating Junction Temperature TJ *40 to +150 °C
Storage Temperature Tstg *65 to +150 °C
Maximum ratings are those values beyond which device damage can occur. Maximum ratings applied to the device are individual stress limit
values (not normal operating conditions) and are not valid simultaneously. If these limits are exceeded, device functional operation is not implied,
damage may occur and reliability may be affected.
A. This device series contains ESD protection and exceeds the following tests:
Pins 1−3: Human Body Model 2000 V per MIL−STD−883, Method 3015.
Machine Model Method 400 V.
Pin 5: Human Body Model 1000 V per MIL−STD−883, Method 3015.
Machine Model Method 400 V.
Pin 5 is connected to the power switch and start−up circuits, and is rated only to the max voltage of the part, or 700 V.
B. This device contains Latch−up protection and exceeds $100 mA per JEDEC Standard JESD78.

http://onsemi.com
6
 NCP1050, NCP1051, NCP1052, NCP1053, NCP1054, NCP1055

ELECTRICAL CHARACTERISTICS (VCC = 8.0 V, for typical values TJ = 25°C, for min/max values, TJ is the operating junction
temperature range that applies (Note 1), unless otherwise noted.)
Characteristics Symbol Min Typ Max Unit
OSCILLATOR
Frequency (VCC = 7.5 V) fOSC(low) kHz
TJ = 25°C:
44 kHz Version 38 42.5 47
100 kHz Version 87 97 107
136 kHz Version 119 132 145
TJ = Tlow to Thigh
44 kHz Version 37 − 47
100 kHz Version 84 − 107
136 kHz Version 113 − 145
Frequency (VCC = 8.5 V) fOSC(high) kHz
TJ = 25°C:
44 kHz Version 41 45.5 50
100 kHz Version 93 103 113
136 kHz Version 126 140 154
TJ = Tlow to Thigh
44 kHz Version 39 − 50
100 kHz Version 90 − 113
136 kHz Version 120 − 154
Frequency Sweep (VCC = 7.5 V to 8.5 V, TJ = 25°C) %fOSC − 5.0 − %
Maximum Duty Cycle D(max) 74 77 80 %
CONTROL INPUT
Lower Window Input Current Threshold A
Switching Enabled, Sink Current Increasing Ioff(low) −58 −47.5 −37
Switching Disabled, Sink Current Decreasing Ion(low) −50 −37.5 −25
Upper Window Input Current Threshold
Switching Enabled, Source Current Increasing Ioff(high) 37 47.5 58
Switching Disabled, Source Current Decreasing Ion(high) 25 37.5 50
Control Window Input Voltage V
Lower (Isink = 25 A) Vlow 1.1 1.35 1.6
Upper (Isource = 25 A) 4.2 4.6 5.0
Vhigh
1. Tested junction temperature range for the NCP105X series:
Tlow = −40°C Thigh = +125°C

http://onsemi.com
7
 NCP1050, NCP1051, NCP1052, NCP1053, NCP1054, NCP1055

ELECTRICAL CHARACTERISTICS (VCC = 8.0 V, for typical values TJ = 25°C, for min/max values, TJ is the operating junction
temperature range that applies (Note 2), unless otherwise noted.)
Characteristics Symbol Min Typ Max Unit
POWER SWITCH CIRCUIT
Power Switch Circuit On−State Resistance RDS(on) 
NCP1050, NCP1051, NCP1052 (ID = 50 mA)
TJ = 25°C − 22 30
TJ = 125°C − 42 55
NCP1053, NCP1054, NCP1055 (ID = 100 mA)
TJ = 25°C − 10 15
TJ = 125°C − 23 28
Power Switch Circuit & Startup Breakdown Voltage V(BR)DS 700 − − V
(ID(off) = 100 A, TA = 25°C)
Power Switch Circuit & Startup Circuit Off−State Leakage Current IDS(off) A
(VDS = 650 V) TJ = 25°C − 25 40
(VDS = 650 V) TJ = 125°C − 15 80
Switching Characteristics (RL = 50 , VDS set for ID = 0.7 IIim) ns
Turn−on Time (90% to 10%) ton − 20 −
Turn−off Time (10% to 90%) − 10 −
toff

CURRENT LIMIT AND THERMAL PROTECTION

Current Limit Threshold (TJ = 25°C) (Note 5) Ilim mA
NCP1050 93 100 107
NCP1051 186 200 214
NCP1052 279 300 321
NCP1053 372 400 428
NCP1054 493 530 567
NCP1055 632 680 728
Conversion Power Deviation (TJ = 25°C) (Note 6) I2fOSC − 0 10 %A2Hz
Propagation Delay, Current Limit Threshold to Power Switch Circuit Output tPLH ns
NCP1050, NCP1051, NCP1052 − 135 −
NCP1053, NCP1054, NCP1055 − 160 −
Thermal Protection (VCC = 8.6 V) (Note 2, 3, 4) °C
Shutdown (Junction Temperature Increasing) Tsd 140 160 −
Hysteresis (Junction Temperature Decreasing) − 75 −
TH

STARTUP CONTROL
Startup/V CC Regulation V
Startup Threshold/VCC Regulation Peak (VCC Increasing) VCC(on) 8.0 8.5 9.0
Minimum Operating/VCC Valley Voltage After Turn−On VCC(off) 7.0 7.5 8.0
Hysteresis VH − 1.0 −
Undervoltage Lockout Threshold Voltage, VCC Decreasing VCC(reset) 4.0 4.5 5.0 V
Startup Circuit Output Current (Power Switch Circuit Output = 40 V) Istart mA
VCC = 0 V
TJ = 25°C 5.4 6.3 7.2
TJ = −40 to 125°C 4.5 − 8.0
VCC = VCC(on) − 0.2 V
TJ = 25°C 4.6 5.6 6.6
TJ = −40 to 125°C 3.5 − 7.0

Minimum Start−up Drain Voltage (Istart = 0.5 mA, VCC = VCC(on) − 0.2 V) Vstart(min) − 13.4 20 V
Output Fault Condition Auto Restart
(VCC Capacitor = 10 F, Power Switch Circuit Output = 40 V)
Average Switching Duty Cycle Drst − 6.0 − %
Frequency frst − 3.5 − Hz
2. Tested junction temperature range for the NCP105X series:
Tlow = −40°C Thigh = +125°C
3. Maximum package power dissipation limits must be observed.
4. Guaranteed by design only.
5. Adjust di/dt to reach Ilim in 4.0 sec.
6. Consult factory for additional options including test and trim for output power accuracy.

http://onsemi.com
8
 NCP1050, NCP1051, NCP1052, NCP1053, NCP1054, NCP1055

ELECTRICAL CHARACTERISTICS (VCC = 8.0 V, for typical values TJ = 25°C, for min/max values, TJ is the operating junction
temperature range that applies (Note 7), unless otherwise noted.)
Characteristics Symbol Min Typ Max Unit
TOTAL DEVICE
Power Supply Current After UVLO Turn−On (Note 8) mA
Power Switch Circuit Enabled ICC1
NCP1050, NCP1051, NCP1052
44 kHz Version 0.35 0.45 0.55
100 kHz Version 0.40 0.50 0.60
136 kHz Version 0.40 0.525 0.65
NCP1053, NCP1054, NCP1055
44 kHz Version 0.40 0.50 0.60
100 kHz Version 0.45 0.575 0.70
136 kHz Version 0.50 0.65 0.80
Power Switch Circuit Disabled
Non−Fault Condition ICC2 0.35 0.45 0.55
Fault Condition ICC3 0.10 0.175 0.25
7. Tested junction temperature range for the NCP105X series:
Tlow = −40°C Thigh = +125°C
8. See Non−Latching Fault Condition Timing Diagram in Figure 4.

http://onsemi.com
9
 NCP1050, NCP1051, NCP1052, NCP1053, NCP1054, NCP1055

46 104
OSCILLATOR FREQUENCY (kHz) VCC = VCC(on)

OSCILLATOR FREQUENCY (kHz)

VCC = VCC(on)
45 102

44 100
VCC = VCC(off)
43 98
VCC = VCC(off)
42 96

41 94

40 92
−50 −25 0 25 50 75 100 125 150 −50 −25 0 25 50 75 100 125 150
TEMPERATURE (°C) TEMPERATURE (°C)

Figure 5. Oscillator Frequency Figure 6. Oscillator Frequency

(44 kHz Version) versus Temperature (100 kHz Version) versus Temperature

142 9
VCC = VCC(on)
OSCILLATOR FREQUENCY (kHz)

140 8

FREQUENCY SWEEP (kHz)

136 kHz
138 7

136 6 100 kHz

134 5
VCC = VCC(off)
132 4

130 3 44 kHz

128 2

126 1
124 0
−50 −25 0 25 50 75 100 125 150 −50 −25 0 25 50 75 100 125 150
TEMPERATURE (°C) TEMPERATURE (°C)

Figure 7. Oscillator Frequency Figure 8. Frequency Sweep versus

(136 kHz Version) versus Temperature Temperature
SINK CONTROL CURRENT THRESHOLD (A)

77.6 55

77.4
MAXIMUM DUTY CYCLE (%)

50 CURRENT RISING
77.2

77.0 45

76.8
40 CURRENT FALLING
76.6
35
76.4

76.2 30
−50 −25 0 25 50 75 100 125 150 −50 −25 0 25 50 75 100 125 150
TEMPERATURE (°C) TEMPERATURE (°C)

Figure 9. Maximum Duty Cycle versus Figure 10. Lower Window Control Input
Temperature Current Thresholds versus Temperature

http://onsemi.com
10
 NCP1050, NCP1051, NCP1052, NCP1053, NCP1054, NCP1055

SOURCE CONTROL CURRENT THRESHOLD (A) 50 1.39

1.38
CURRENT RISING
46 1.37

CLAMP VOLTAGE (V)

1.36
1.35
42
1.34
1.33 ISINK = 25 A
38
CURRENT FALLING 1.32
1.31
34 1.30
1.29
30 1.28
−50 −25 0 25 50 75 100 125 150 −50 −25 0 25 50 75 100 125 150
TEMPERATURE (°C) TEMPERATURE (°C)

Figure 11. Upper Window Control Input Figure 12. Control Input Lower Window Clamp
Current Thresholds versus Temperature Voltage versus Temperature

4.66 45
40
4.64 NCP1050,1,2
35 (ID = 50 mA)
CLAMP VOLTAGE (V)

ON RESISTANCE ()
4.62
30
4.60 25

4.58 ISOURCE = 25 A 20
NCP1053,4,5
15
4.56 (ID = 100 mA)
10
4.54
5
4.52 0
−50 −25 0 25 50 75 100 125 150 −50 −25 0 25 50 75 100 125 150
TEMPERATURE (°C) TEMPERATURE (°C)

Figure 13. Control Input Upper Window Clamp Figure 14. On Resistance versus Temperature
Voltage versus Temperature

120 100
TJ = 25°C
100
LEAKAGE CURRENT (A)

NCP1053,4,5
CAPACITANCE (pF)

80

60 10
TJ = −40°C NCP1050,1,2
40
TJ = 25°C
20
TJ = 125°C
0 1
0 100 200 300 400 500 600 700 800 900 0 100 200 300 400 500 600 700
APPLIED VOLTAGE (V) APPLIED VOLTAGE (V)

Figure 15. Power Switch and Startup Circuit Figure 16. Power Switch and Startup Circuit
Leakage Current versus Voltage Output Capacitance versus Applied Voltage

http://onsemi.com
11
 NCP1050, NCP1051, NCP1052, NCP1053, NCP1054, NCP1055

1.02 8.6
STARTUP
NORMALIZED CURRENT LIMIT
1.00 8.4 THRESHOLD

SUPPLY THRESHOLD (V)

VCC(on)
0.98 8.2

0.96 8.0
MINIMUM
0.94 7.8 OPERATING
THRESHOLD
0.92 7.6 VCC(off)

0.90 7.4

0.88 7.2
−50 −25 0 25 50 75 100 125 150 −50 −25 0 25 50 75 100 125 150
TEMPERATURE (°C) TEMPERATURE (°C)

Figure 17. Normalized Peak Current Limit Figure 18. Supply Voltage Thresholds versus
versus Temperature Temperature

4.56 8
UNDERVOLTAGE THRESHOLD (V)

4.54
7
4.52 VCC = 0 V
START CURRENT (mA) 6
4.50
4.48 5
4.46
4
4.44 VCC = 8.3 V
4.42 3
4.40 2
4.38 VPIN 5 = 20 V
1
4.36
4.34 0
−50 −25 0 25 50 75 100 125 150 −50 −25 0 25 50 75 100 125 150
TEMPERATURE (°C) TEMPERATURE (°C)

Figure 19. Undervoltage Lockout Threshold Figure 20. Start Current versus Temperature
versus Temperature

7 8
VCC = 0 V
6
STARTUP CURRENT (mA)
STARTUP CURRENT (mA)

6
VCC = 8 V
5
4
4

3 2
TJ = 25°C
2
VPIN 5 = 20 V
0
1 TJ = 25°C

0 −2
0 1 2 3 4 5 6 7 8 9 1 10 100 1000
SUPPLY VOLTAGE (V) PIN 5 VOLTAGE (V)

Figure 21. Startup Current versus Supply Figure 22. Startup Current versus Pin 5
Voltage Voltage

http://onsemi.com
12
 NCP1050, NCP1051, NCP1052, NCP1053, NCP1054, NCP1055

0.55 0.70
136 kHz 136 kHz
0.65

SUPPLY CURRENT (mA)

SUPPLY CURRENT (mA)

0.50
0.60
100 kHz
100 kHz
0.55
0.45
44 kHz 0.50
44 kHz
0.45
0.40
0.40

0.35 0.35
−50 −25 0 25 50 75 100 125 150 −50 −25 0 25 50 75 100 125 150
TEMPERATURE (°C) TEMPERATURE (°C)

Figure 23. Supply Current versus Temperature Figure 24. Supply Current versus Temperature
(NCP1050/1/2) (NCP1053/4/5)

0.48 0.21
0.20
0.47
SUPPLY CURRENT (mA)

SUPPLY CURRENT (mA) 0.19

0.46
0.18
0.45 0.17

0.44 0.16
0.15
0.43
0.14
0.42 0.13
0.41 0.12
−50 −25 0 25 50 75 100 125 150 −50 −25 0 25 50 75 100 125 150
TEMPERATURE (°C) TEMPERATURE (°C)

Figure 25. Supply Current When Switching Figure 26. Supply Current in Fault Condition
Disable versus Temperature versus Temperature

14.0
CONDITION:
13.9
VCC pin = 1 F to ground
13.8 Control pin = open
SUPPLY VOLTAGE (V)

13.7 Drain pin = 1 k to Power Supply,

Increase Voltage Until Switching
13.6
13.5
13.4
13.3
13.2
13.1
13.0
−50 −25 0 25 50 75 100 125 150
TEMPERATURE (°C)

Figure 27. Supply Voltage versus Temperature

http://onsemi.com
13
 NCP1050, NCP1051, NCP1052, NCP1053, NCP1054, NCP1055

OPERATING DESCRIPTION
Introduction followers at approximately 47.5 A with 10 A hysteresis.
The NCP105X series represents a new higher level of When a source or sink current in excess of this value is
integration by providing on a single monolithic chip all of applied to this input, a logic signal generated internally
the active power, control, logic, and protection circuitry changes state to block power switch conduction. Since the
required to implement a high voltage flyback converter and output of the Control Input sense is sampled continuously
compliance with very low standby power requirements for during ton (77% duty cycle), it is possible to turn the Power
modern consumer electronic power supplies. This device Switch Circuit on or off at any time within ton. Because it
series is designed for direct operation from a rectified 240 does not have to wait for the next cycle (rising edge of the
VAC line source and requires minimal external components clock signal) to switch on, and because it does not have to
for a complete cost sensitive converter solution. Potential wait for current limit to turn off, the circuit has a very fast
markets include cellular phone chargers, standby power transient response as shown in Figure 3.
supplies for personal computers, secondary bias supplies for In a typical converter application the control input current
microprocessor keep−alive supplies and IR detectors. A is drawn by an optocoupler. The collector of the optocoupler
description of each of the functional blocks is given below, is connected to the Control Input pin and the emitter is
and the representative block diagram is shown in Figure 2. connected to ground. The optocoupler LED is mounted in
This device series features an active startup regulator series with a shunt regulator (typically a TL431) at the DC
circuit that eliminates the need for an auxiliary bias winding output of the converter. When the power supply output is
on the converter transformer, fault logic with a programmable greater than the reference voltage (shunt regulator voltage
timer for converter overload protection, unique gated plus optocoupler diode voltage drop), the optocoupler turns
oscillator configuration for extremely fast loop response with on, pulling down on the Control Input. The control input
double pulse suppression, oscillator frequency dithering with logic is configured for line input sensing as well.
a controlled slew rate driver for reduced EMI,
Turn On Latch
cycle−by−cycle current limiting, input undervoltage lockout
The Oscillator output is typically a 77% positive duty
with hysteresis, thermal shutdown, and auto restart or latched
cycle square waveform. This waveform is inverted and
off fault detect device options. These devices are available in
applied to the reset input of the turn−on latch to prevent any
economical 8−pin PDIP and 4−pin SOT−223 packages.
power switch conduction during the guaranteed off time.
Oscillator This square wave is also gated by the output of the control
The Oscillator is a unique fixed−frequency, duty−cycle− section and applied to the set input of the same latch.
controlled oscillator. It charges and discharges an on chip Because of this gating action, the power switch can be
timing capacitor to generate a precise square wave signal activated when the control input is not asserted and the
used to pulse width modulate the Power Switch Circuit. oscillator output is high.
During the discharge of the timing capacitor, the Oscillator The use of this unique gated Turn On Latch over an
duty cycle output holds one input of the Driver low. This ordinary Gated Oscillator allows a faster load transient
action keeps the Power Switch Circuit off, thus limiting the response. The power switch is allowed to turn on
maximum duty cycle. immediately, within the maximum duty cycle time period,
A frequency modulation feature is incorporated into the when the control input signals a necessary change in state.
IC in order to aide in EMI reduction. Figure 3 illustrates this
Turn Off Latch
frequency modulation feature. The power supply voltage,
A Turn Off Latch feature has been incorporated into this
VCC, acts as the input to the built−in voltage controlled
device series to protect the power switch circuit from
oscillator. As the VCC voltage is swept across its nominal
excessive current, and to reduce the possibility of output
operating range of 7.5 to 8.5 V, the oscillator frequency is
overshoot in reaction to a sudden load removal. If the Power
swept across its corresponding range.
Switch current reaches the specified maximum current limit,
The center oscillator frequency is internally programmed
the Current Limit Comparator resets the Turn Off Latch and
for 44 kHz, 100 kHz, or 136 kHz operation with a controlled
turns the Power Switch Circuit off. The turn off latch is also
charge to discharge current ratio that yields a maximum
reset when the Oscillator output signal goes low or the
Power Switch duty cycle of 77%. The Oscillator
Control Input is asserted, thus terminating output MOSFET
temperature characteristics are shown in Figures 5
conduction. Because of this response to control input
through 9. Contact an ON Semiconductor sales
signals, it provides a very fast transient response and very
representative for further information regarding frequency
tight load regulation. The turn off latch has an edge triggered
options.
set input which ensures that the switch can only be activated
Control Input once during any oscillator period. This is commonly
The Control Input pin circuit has parallel source follower referred to as double pulse suppression.
input stages with voltage clamps set at 1.35 and 4.6 V.
Current sources clamp the input current through the

http://onsemi.com
14
 NCP1050, NCP1051, NCP1052, NCP1053, NCP1054, NCP1055

Current Limit Comparator and Power Switch Circuit Undervoltage Lockout

The Power Switch Circuit is constructed with a An Undervoltage Lockout (UVLO) comparator is
SENSEFET™ in order to monitor the drain current. A included to guarantee that the integrated circuit has
portion of the current flowing through the circuit goes into sufficient voltage to be fully functional. The UVLO
a sense element, Rsense. The current limit comparator detects comparator monitors the supply capacitor input voltage at
if the voltage across Rsense exceeds the reference level that Pin 1 and disables the Power Switch Circuit whenever the
is present at its inverting input. If this level is exceeded, the capacitor voltage drops below the undervoltage lockout
comparator quickly resets the Turn Off Latch, thus threshold. When this level is crossed, the controller enters a
protecting the Power Switch Circuit. new startup phase by turning the current source on. The
A Leading Edge Blanking circuit was placed in the current supply voltage will then have to exceed the startup threshold
sensing signal path to prevent a premature reset of the Turn in order to turn off the startup current source. Startup and
Off Latch. A potential premature reset signal is generated normal operation of the converter are shown in Figure 3.
each time the Power Switch Circuit is driven into conduction
Fault Detector
and appears as a narrow voltage spike across current sense
The NCP105X series has integrated Fault Detector
resistor Rsense. The spike is due to the Power Switch Circuit circuitry for detecting application fault conditions such as
gate to source capacitance, transformer interwinding
open loop, overload or a short circuited output. A timer is
capacitance, and output rectifier recovery time. The Leading generated by driving the supply capacitor with a known
Edge Blanking circuit has a dynamic behavior that masks the current and hysteretically regulating the supply voltage
current signal until the Power Switch Circuit turn−on
between set thresholds. The timer period starts when the
transition is completed. The current limit propagation delay supply voltage reaches the nominal upper threshold of 8.5 V
time is typically 135 to 165 nanoseconds. This time is
and stops when the drain current of the integrated circuit
measured from when an overcurrent appears at the Power
draws the supply capacitor voltage down to the undervoltage
Switch Circuit drain, to the beginning of turn−off. Care must lockout threshold of 7.5 V.
be taken during transformer saturation so that the maximum
If, during this timer period, no feedback has been applied
device current limit rating is not exceeded. to the control input, the fault detect logic is set to indicate an
The high voltage Power Switch Circuit is monolithically abnormal condition. This may occur, for example, when the
integrated with the control logic circuitry and is designed to
optocoupler fails or the output of the application is
directly drive the converter transformer. Because the overloaded or completely shorted. In this case, the part will
characteristics of the power switch circuit are well known,
stop switching, go into a low power mode, and begin to draw
the gate drive has been tailored to control switching
down the supply capacitor to the reset threshold voltage of
transitions to help limit electromagnetic interference (EMI). 4.5 V. At that time, the startup circuit will turn on again to
The Power Switch Circuit is capable of switching 700 V
drive the supply to the turn on threshold. Then the part will
with an associated drain current that ranges nominally from
begin the cycle again, effectively sampling the control input
0.10 to 0.68 Amps. to determine if the fault condition has been removed. This
Startup Circuit mode is commonly referred to as burst mode operation and
Rectified AC line voltage is applied to the Startup Circuit is shown is Figure 4.
on Pin 5, through the primary winding. The circuit is Proper selection of the supply capacitor allows successful
self−biasing and acts as a constant current source, gated by startup with monotonically increasing output voltage,
control logic. Upon application of the AC line voltage, this without falsely sensing a fault condition. Figure 4 shows
circuit routes current into the supply capacitor typically successful startup and the evolution of the signals involved
connected to Pin 1. During normal operation, this capacitor in the presence of a fault.
is hysteretically regulated from 7.5 to 8.5 V by monitoring
Thermal Shutdown
the supply voltage with a comparator and controlling the The internal Thermal Shutdown block protects the device
startup current source accordingly. This Dynamic
in the event that the maximum junction temperature is
Self−Supply (DSS) functionality offers a great deal of
exceeded. When activated, typically at 160°C, one input of
applications flexibility as well. The startup circuit is rated at the Driver is held low to disable the Power Switch Circuit.
a maximum 700 V (maximum power dissipation limits must
The Power Switch is allowed to resume operation when the
be observed). junction temperature falls below 85°C. The thermal
shutdown feature is provided to prevent catastrophic device
failures from accidental overheating. It is not intended to be
used as a substitute for proper heatsinking.

http://onsemi.com
15
 NCP1050, NCP1051, NCP1052, NCP1053, NCP1054, NCP1055

APPLICATIONS

Two application examples have been provided in this to provide a tightly regulated DC output. IC3 is a shunt
document, and they are described in detail in this section. regulator that samples the output voltage by virtue of R5 and
Figure 28 shows a Universal Input, 6 Watt Converter R6 to provide drive to the optocoupler, IC2, Light Emitting
Application as well as a 5.5 Watt Charger Application using Diode (LED). C10 is used to compensate the shunt regulator.
the NCP1053 @ 100 kHz. The Charger consists of the When the application is configured as a Charger, Q1 delivers
additional components Q1, C13, and R7 through R10, as additional drive to the optocoupler LED when in constant
shown. These were constructed and tested using the printed current operation by sampling the output current through R7
circuit board layout shown in Figure 40. The board consists and R8.
of a fiberglass epoxy material (FR4) with a single side of two
ounce per square foot (70 m thick) copper foil. Test data Component Selection Guidelines
from the two applications is given in Figures 29 through 39. Choose snubber components R1, C3, and D5 such that the
Both applications generate a well−regulated output voltage on pin 5 is limited to the range from 0 to 700 volts.
voltage over a wide range of line input voltage and load These components protect the IC from substrate injection if
current values. The charger application transitions to a the voltage was to go below zero volts, and from avalanche
constant current output if the load current is increased if the voltage was to go above 700 volts, at the cost of slightly
beyond a preset range. This can be very effective for battery reduced efficiency. For lower power design, a simple RC
charger application for portable products such as cellular snubber as shown, or connected to ground, can be sufficient.
telephones, personal digital assistants, and pagers. Using the Ensure that these component values are chosen based upon
NCP105X series in applications such as these offers a wide the worst−case transformer leakage inductance and
range of flexibility for the system designer. worst−case applied voltage. Choose R2 and C4 for best
The NCP105X application offers a low cost alternative to performance radiated switching noise.
other applications. It uses a Dynamic Self−Supply (DSS) Capacitor C5 serves multiple purposes. It is used along
function to generate its own operating supply voltage such with the internal startup circuitry to provide power to the IC
that an auxiliary transformer winding is not needed. (It also in lieu of a separate auxiliary winding. It also serves to
offers the flexibility to override this function with an provide timing for the oscillator frequency sweep for
auxiliary winding if ultra−low standby power is the limiting the conducted EMI emissions. The value of C5 will
designer’s main concern.) This product also provides for also determine the response during an output fault (overload
automatic output overload, short circuit, and open loop or short circuit) or open loop condition as shown in Figure 4,
protection by entering a programmable duty cycle burst along with the total output capacitance.
mode of operation. This eliminates the need for expensive Resistors R5 and R6 will determine the regulated output
devices overrated for power dissipation or maximum voltage along with the reference voltage chosen with IC3.
current, or for redundant feedback loops. The base to emitter voltage drop of Q1 along with the
The application shown in Figure 28 can be broken down value of R7 will set the fixed current limit value of the
into sections for the purpose of operating description. Charger application. R9 is used to limit the base current of
Components C1, L1 and C6 provide EMI filtering for the Q1. Component R8 can be selected to keep the current limit
design, although this is very dependent upon board layout, fixed with very low values of output voltage or to provide
component type, etc. D1 through D4 along with C2 provide current limit foldback with results as shown in
the AC to bulk DC rectification. The NCP1053 drives the Figures 29 and 33. A relatively large value of R8 allows for
primary side of the transformer, and the capacitor, C5, is an enough output voltage to effectively drive the optocoupler
integral part of the Dynamic Self−Supply. R1, C3, and D5 LED for fixed current limit. A low value of R8, along with
comprise an RCD snubber and R2 and C4 comprise a ringing resistor R10, provides for a low average output power using
damper both acting together to protect the IC from voltage the fault protection feature when the output voltage is very
transients greater than 700 volts and reduce radiated noise low. C13 provides for output voltage stability when the
from the converter. Diode D6 along with C7−9, L2, C11, and Charger application is in current limit.
C12 rectify the transformer secondary and filter the output

http://onsemi.com
16
 F1 D1 D6 L2
2.0 A 1N4006 1N5822 5 H
T1
C4
50 p 5.25 V
D2 R1 C3 1.2 A
C7 C8 C9
L1 1N4006 91 k 220 p 330 330 330 R3
10 mH
Vin R2 47 R6
85 − 265 VAC C1 2.2 k 2.20 k
0.1 D3
IC2
1N4006
SFH 615A−4
D5
C2 MUR160 C12
R4* C11
D4 33 1.0
1.0 k 220
1N4006

C13* R10*

17
1.0 220 C10
0.22
NCP1053B R9*
22 
(100 kHz)

http://onsemi.com
Q1* IC3
2N3904 TL431 R5
C5 2.00 k
10
C6 R7* R8*
100 p 0.5 /1 W 1.2 /1 W

Figure 28. Universal Input 6/5 Watt Converter/Charger Application

T1: COOPER ELECTRONIC TECHNOLOGIES
PART # CTX22−15348
PRIMARY: 97 turns of #29 AWG, Pin 4 = start, Pin 5 = finish
SECONDARY: 5 turns of 0.40 mm, Pins 2 and 1 = start, Pins 7 and 8 = finish
NCP1050, NCP1051, NCP1052, NCP1053, NCP1054, NCP1055

GAP: Designed for Total 1.24 mH Primary Inductance

CORE: TSF−7070
BOBBIN: Pins 3 and 6 Removed, EE19

* Add Q1, C13, and R7−R10, and Change R4 to 2.0 k for Charger Output
 NCP1050, NCP1051, NCP1052, NCP1053, NCP1054, NCP1055

Test Conditions Converter Results Charger Results

Line Regulation Vin = 85 − 265 VAC; Iout = 120 mA 2 mV
Vin = 85 − 265 VAC; Iout = 600 mA 1 mV
Vin = 85 − 265 VAC; Iout = 1.2 A 2 mV
Vin = 85 − 265 VAC; Iout = 100 mA 11 mV
Vin = 85 − 265 VAC; Iout = 500 mA 24 mV
Vin = 85 − 265 VAC; Iout = 1.00 A 41 mV
Load Regulation Vin = 85 VAC; Iout = 120 mA − 1.2 A 12 mV
Vin = 110 VAC; Iout = 120 mA − 1.2 A 13 mV
Vin = 230 VAC; Iout = 120 mA − 1.2 A 12 mV
Vin = 265 VAC; Iout = 120 mA − 1.2 A 13 mV
Vin = 85 VAC; Iout = 100 mA − 1.00 A 58 mV
Vin = 110 VAC; Iout = 100 mA − 1.00 A 65 mV
Vin = 230 VAC; Iout = 100 mA − 1.00 A 71 mV
Vin = 265 VAC; Iout = 100 mA − 1.00 A 67 mV
Output Ripple Vin = 110 VAC; Iout = 1.2 A 86 mVp−p
Vin = 230 VAC; Iout = 1.2 A 127 mVp−p

Vin = 110 VAC; Iout = 1.00 A 80 mVp−p

Vin = 230 VAC; Iout = 1.00 A 155 mVp−p
Efficiency Vin = 110 VAC; Iout = 1.2 A 72.4%
Vin = 230 VAC; Iout = 1.2 A 69.6%

Vin = 110 VAC; R8 = 1.2 , Iout = 1.00 A 54.6%

Vin = 230 VAC; R8 = 1.2 , Iout = 1.00 A 53.6%

Vin = 110 VAC; R8 = 0 , Iout = 1.00 A 66.1%

Vin = 230 VAC; R8 = 0 , Iout = 1.00 A 63.3%

No Load Input Power Vin = 110 VAC; Iout = 0 A 100 mW 100 mW

Vin = 230 VAC; Iout = 0 A 200 mW 200 mW

Standby Output Power Vin = 110 VAC; Pin = 1 W 680 mW 640 mW

Vin = 230 VAC; Pin = 1 W 630 mW 540 mW
Short Circuit Load Input Power Vin = 110 VAC; Vout = 0 V (Shorted) 400 mW
Vin = 230 VAC; Vout = 0 V (Shorted) 550 mW

Vin = 110 VAC; R8 = 1.2 , Vout = 0 V (Shorted) 750 mW

Vin = 230 VAC; R8 = 1.2 , Vout = 0 V (Shorted) 900 mW

Vin = 110 VAC; R8 = 0 , Vout = 0 V (Shorted) 700 mW

Vin = 230 VAC; R8 = 0 , Vout = 0 V (Shorted) 850 mW

Figure 29. Converter and Charger Test Data Summary

http://onsemi.com
18
 NCP1050, NCP1051, NCP1052, NCP1053, NCP1054, NCP1055

5.224 5.23

5.222 Iout = 120 mA 5.22

OUTPUT VOLTAGE (VDC)

OUTPUT VOLTAGE (VDC)

5.21 Iout = 100 mA
5.220
Iout = 600 mA 5.20
5.218
5.19
5.216
5.18
5.214
5.17 Iout = 500 mA
5.212 5.16
Iout = 1.2 A
5.210 5.15 Iout = 1 A
5.208 5.14
80 130 180 230 280 80 130 180 230 280
LINE INPUT VOLTAGE (VAC) LINE INPUT VOLTAGE (VAC)

Figure 30. Converter Line Regulation Figure 31. Charger Line Regulation

6 6

5 5
Vin = 230 VAC
OUTPUT VOLTAGE (V)

OUTPUT VOLTAGE (V)

Vin = 85 VAC

4 4
Vin = 110 VAC
3 3 Vin = 265 VAC
Vin = 85 VAC
2 2
Vin = 265 VAC
1 Vin = 110 VAC
1
Vin = 230 VAC
0 0
0 0.5 1 1.5 2 0 0.5 1.0 1.5
LOAD CURRENT (A) LOAD CURRENT (A)

Figure 32. Converter Load Regulation Figure 33. Charger Load Regulation

Ch1: Vout
Ch1: Vout
Ch2: Iout = 0.2 A/div
Ch2: Iout = 0.2 A/div
(Vin = 230 VAC)
(Vin = 230 VAC)

Figure 34. Converter Load Transient Response Figure 35. Charger Load Transient Response

http://onsemi.com
19
 NCP1050, NCP1051, NCP1052, NCP1053, NCP1054, NCP1055

75 70
Vin = 110 VAC
Vin = 85 VAC Vin = 85 VAC
70 65
Vin = 230 VAC Vin = 110 VAC
EFFICIENCY (%)

EFFICIENCY (%)
Vin = 265 VAC
65 60

60 55 Vin = 230 VAC

Vin = 265 VAC

55 50

50 45
0 0.5 1.0 1.5 0 0.5 1.0 1.5
LOAD CURRENT (A) LOAD CURRENT (A)

Figure 36. Converter Efficiency Figure 37. Charger Efficiency

Ch1: Vout Ch1: Vout

Ch2: Rectified Vin Ch2: Rectified Vin
(Vin = 230 VAC, (Vin = 230 VAC,
Iout = 0.5 A) Iout = 0.5 A)

Figure 38. Converter On/Off Line Transient Figure 39. Charger On/Off Line Transient
Response Response

http://onsemi.com
20
NCP1050, NCP1051, NCP1052, NCP1053, NCP1054, NCP1055

BOARD GRAPHICS

AC Input DC Output
IC3 + −
F1

R5
R4

R6
C5
C12
C1
− IC2
C10
+
R9
C11
R8 + −
L1
IC1
Q1 L2

D4 R7
D2
C6 R3
C9
+ −
D3

D1

D5
D6
T1
R2 C8
+ −
R1
C2
− +
C3
C7
C4 + −

Top View

2.75″
NCP1050
Series
2.25″

Bottom View

Figure 40. Printed Circuit Board and Component Layout

http://onsemi.com
21
 NCP1050, NCP1051, NCP1052, NCP1053, NCP1054, NCP1055

DEVICE ORDERING INFORMATION (Note 9)

RDS(on) Ipk
Device (W) (mA) Package Shipping †
NCP1050P44 30 100 PDIP−8 50 Units / Rail
NCP1050P44G 30 100 PDIP−8 50 Units / Rail
(Pb−Free)

NCP1050P100 30 100 PDIP−8 50 Units / Rail

NCP1050P100G 30 100 PDIP−8 50 Units / Rail
(Pb−Free)

NCP1050P136 30 100 PDIP−8 50 Units / Rail

NCP1050P136G 30 100 PDIP−8 50 Units / Rail
(Pb−Free)

NCP1050ST44T3 30 100 SOT−223 4000 / Tape & Reel

NCP1050ST44T3G 30 100 SOT−223 4000 / Tape & Reel
(Pb−Free)
NCP1050ST100T3 30 100 SOT−223 4000 / Tape & Reel
NCP1050ST100T3G 30 100 SOT−223 4000 / Tape & Reel
(Pb−Free)

NCP1050ST136T3 30 100 SOT−223 4000 / Tape & Reel

NCP1050ST136T3G 30 100 SOT−223 4000 / Tape & Reel
(Pb−Free)

NCP1051P44 30 200 PDIP−8 50 Units / Rail

NCP1051P44G 30 200 PDIP−8 50 Units / Rail
(Pb−Free)

NCP1051P100 30 200 PDIP−8 50 Units / Rail

NCP1051P100G 30 200 PDIP−8 50 Units / Rail
(Pb−Free)

NCP1051P136 30 200 PDIP−8 50 Units / Rail

NCP1051P136G 30 200 PDIP−8 50 Units / Rail
(Pb−Free)

NCP1051ST44T3 30 200 SOT−223 4000 / Tape & Reel

NCP1051ST44T3G 30 200 SOT−223 4000 / Tape & Reel
(Pb−Free)

NCP1051ST100T3 30 200 SOT−223 4000 / Tape & Reel

NCP1051ST100T3G 30 200 SOT−223 4000 / Tape & Reel
(Pb−Free)
NCP1051ST136T3 30 200 SOT−223 4000 / Tape & Reel
NCP1051ST136T3G 30 200 SOT−223 4000 / Tape & Reel
(Pb−Free)

NCP1052P44 30 300 PDIP−8 50 Units / Rail

NCP1052P44G 30 300 PDIP−8 50 Units / Rail
(Pb−Free)

NCP1052P100 30 300 PDIP−8 50 Units / Rail

NCP1052P100G 30 300 PDIP−8 50 Units / Rail
(Pb−Free)
NCP1052P136 30 300 PDIP−8 50 Units / Rail
†For information on tape and reel specifications, including part orientation and tape sizes, please refer to our Tape and Reel Packaging Specifi-
cations Brochure, BRD8011/D.
9. Consult factory for additional optocoupler fail−safe latching, frequency, current limit and line input options.

http://onsemi.com
22
 NCP1050, NCP1051, NCP1052, NCP1053, NCP1054, NCP1055

DEVICE ORDERING INFORMATION (Note 9)

RDS(on) Ipk
Device (W) (mA) Package Shipping †
NCP1052P136G 30 300 PDIP−8 50 Units / Rail
(Pb−Free)

NCP1052ST44T3 30 300 SOT−223 4000 / Tape & Reel

NCP1052ST44T3G 30 300 SOT−223 4000 / Tape & Reel
(Pb−Free)
NCP1052ST100T3 30 300 SOT−223 4000 / Tape & Reel
NCP1052ST100T3G 30 300 SOT−223 4000 / Tape & Reel
(Pb−Free)

NCP1052ST136T3 30 300 SOT−223 4000 / Tape & Reel

NCP1052ST136T3G 30 300 SOT−223 4000 / Tape & Reel
(Pb−Free)

NCP1053P44 15 400 PDIP−8 50 Units / Rail

NCP1053P44G 15 400 PDIP−8 50 Units / Rail
(Pb−Free)

NCP1053P100 15 400 PDIP−8 50 Units / Rail

NCP1053P100G 15 400 PDIP−8 50 Units / Rail
(Pb−Free)

NCP1053P136 15 400 PDIP−8 50 Units / Rail

NCP1053P136G 15 400 PDIP−8 50 Units / Rail
(Pb−Free)

NCP1053ST44T3 15 400 SOT−223 4000 / Tape & Reel

NCP1053ST44T3G 15 400 SOT−223 4000 / Tape & Reel
(Pb−Free)

NCP1053ST100T3 15 400 SOT−223 4000 / Tape & Reel

NCP1053ST100T3G 15 400 SOT−223 4000 / Tape & Reel
(Pb−Free)
NCP1053ST136T3 15 400 SOT−223 4000 / Tape & Reel
NCP1053ST136T3G 15 400 SOT−223 4000 / Tape & Reel
(Pb−Free)

NCP1054P44 15 530 PDIP−8 50 Units / Rail

NCP1054P44G 15 530 PDIP−8 50 Units / Rail
(Pb−Free)

NCP1054P100 15 530 PDIP−8 50 Units / Rail

NCP1054P100G 15 530 PDIP−8 50 Units / Rail
(Pb−Free)
NCP1054P136 15 530 PDIP−8 50 Units / Rail
NCP1054P136G 15 530 PDIP−8 50 Units / Rail
(Pb−Free)

NCP1054ST44T3 15 530 SOT−223 4000 / Tape & Reel

NCP1054ST44T3G 15 530 SOT−223 4000 / Tape & Reel
(Pb−Free)

NCP1054ST100T3 15 530 SOT−223 4000 / Tape & Reel

NCP1054ST100T3G 15 530 SOT−223 4000 / Tape & Reel
(Pb−Free)
†For information on tape and reel specifications, including part orientation and tape sizes, please refer to our Tape and Reel Packaging Specifi-
cations Brochure, BRD8011/D.
9. Consult factory for additional optocoupler fail−safe latching, frequency, current limit and line input options.

http://onsemi.com
23
 NCP1050, NCP1051, NCP1052, NCP1053, NCP1054, NCP1055

DEVICE ORDERING INFORMATION (Note 9)

RDS(on) Ipk
Device (W) (mA) Package Shipping †
NCP1054ST136T3 15 530 SOT−223 4000 / Tape & Reel
NCP1054ST136T3G 15 530 SOT−223 4000 / Tape & Reel
(Pb−Free)

NCP1055P44 15 680 PDIP−8 50 Units / Rail

NCP1055P44G 15 680 PDIP−8 50 Units / Rail
(Pb−Free)

NCP1055P100 15 680 PDIP−8 50 Units / Rail

NCP1055P100G 15 680 PDIP−8 50 Units / Rail
(Pb−Free)

NCP1055P136 15 680 PDIP−8 50 Units / Rail

NCP1055P136G 15 680 PDIP−8 50 Units / Rail
(Pb−Free)

NCP1055ST44T3 15 680 SOT−223 4000 / Tape & Reel

NCP1055ST44T3G 15 680 SOT−223 4000 / Tape & Reel
(Pb−Free)
NCP1055ST100T3 15 680 SOT−223 4000 / Tape & Reel
NCP1055ST100T3G 15 680 SOT−223 4000 / Tape & Reel
(Pb−Free)

NCP1055ST136T3 15 680 SOT−223 4000 / Tape & Reel

NCP1055ST136T3G 15 680 SOT−223 4000 / Tape & Reel
(Pb−Free)

†For information on tape and reel specifications, including part orientation and tape sizes, please refer to our Tape and Reel Packaging Specifi-
cations Brochure, BRD8011/D.
9. Consult factory for additional optocoupler fail−safe latching, frequency, current limit and line input options.

http://onsemi.com
24
 NCP1050, NCP1051, NCP1052, NCP1053, NCP1054, NCP1055

PACKAGE DIMENSIONS

PDIP−8
P SUFFIX
CASE 626A−01
ISSUE O
NOTES:
1. DIMENSIONING AND TOLERANCING PER ANSI
Y14.5M, 1982.
2. CONTROLLING DIMENSION: MILLIMETER.
8 5 3. PACKAGE CONTOUR OPTIONAL (ROUND OR
SQUARE CORNERS).
4. DIMENSION L TO CENTER OF LEAD WHEN
B L FORMED PARALLEL.
5. DIMENSIONS A AND B ARE DATUMS.
1 4 M
MILLIMETERS INCHES
J DIM MIN MAX MIN MAX
A 9.40 10.16 0.370 0.400
F B 6.10 6.60 0.240 0.260
C 3.94 4.45 0.155 0.175
NOTE 3 A D 0.38 0.51 0.015 0.020
F 1.02 1.78 0.040 0.070
G 2.54 BSC 0.100 BSC
H 0.76 1.27 0.030 0.050
J 0.20 0.30 0.008 0.012
C K 2.92 3.43 0.115 0.135
L 7.62 BSC 0.300 BSC
M −−− 10 _ −−− 10_
−T− N 0.76 1.01 0.030 0.040
SEATING N
PLANE
D K
H G
0.13 (0.005) M T A M B M

http://onsemi.com
25
 NCP1050, NCP1051, NCP1052, NCP1053, NCP1054, NCP1055

SOT−223 (TO−261)
CASE 318E−04
ISSUE L

NOTES:
D C. DIMENSIONING AND TOLERANCING PER ANSI
b1 Y14.5M, 1982.
D. CONTROLLING DIMENSION: INCH.

MILLIMETERS INCHES
4
DIM MIN NOM MAX MIN NOM MAX
HE E A 1.50 1.63 1.75 0.060 0.064 0.068
1 2 3 A1 0.02 0.06 0.10 0.001 0.002 0.004
b 0.60 0.75 0.89 0.024 0.030 0.035
b1 2.90 3.06 3.20 0.115 0.121 0.126
c 0.24 0.29 0.35 0.009 0.012 0.014
D 6.30 6.50 6.70 0.249 0.256 0.263
b E 3.30 3.50 3.70 0.130 0.138 0.145
e1 e 2.20 2.30 2.40 0.087 0.091 0.094
e e1 0.85 0.94 1.05 0.033 0.037 0.041
L1 1.50 1.75 2.00 0.060 0.069 0.078
HE 6.70 7.00 7.30 0.264 0.276 0.287
C
q q 0° − 10° 0° − 10°
A
0.08 (0003)
A1
L1

SOLDERING FOOTPRINT*
3.8
0.15

2.0
0.079

6.3
2.3 2.3
0.248
0.091 0.091

2.0
0.079

1.5 SCALE 6:1 ǒinches

mm Ǔ
0.059

*For additional information on our Pb−Free strategy and soldering

details, please download the ON Semiconductor Soldering and
Mounting Techniques Reference Manual, SOLDERRM/D.

The products described herein (NCP1050, 1051, 1052, 1053, 1054, 1055), may be covered by one or more of the following U.S. patents: 4,553,084; 5,418,410;
5,477,175; 6,137,696; 6,137,702; 6,271,735, 6,480,043, 6,362,067, 6,587,357. There may be other patents pending.
SENSEFET is a trademark of Semiconductor Components Industries, LLC (SCILLC)

ON Semiconductor and are registered trademarks of Semiconductor Components Industries, LLC (SCILLC). SCILLC reserves the right to make changes without further notice
to any products herein. SCILLC makes no warranty, representation or guarantee regarding the suitability of its products for any particular purpose, nor does SCILLC assume any liability
arising out of the application or use of any product or circuit, and specifically disclaims any and all liability, including without limitation special, consequential or incidental damages.
“Typical” parameters which may be provided in SCILLC data sheets and/or specifications can and do vary in different applications and actual performance may vary over time. All
operating parameters, including “Typicals” must be validated for each customer application by customer’s technical experts. SCILLC does not convey any license under its patent rights
nor the rights of others. SCILLC products are not designed, intended, or authorized for use as components in systems intended for surgical implant into the body, or other applications
intended to support or sustain life, or for any other application in which the failure of the SCILLC product could create a situation where personal injury or death may occur. Should
Buyer purchase or use SCILLC products for any such unintended or unauthorized application, Buyer shall indemnify and hold SCILLC and its officers, employees, subsidiaries, affiliates,
and distributors harmless against all claims, costs, damages, and expenses, and reasonable attorney fees arising out of, directly or indirectly, any claim of personal injury or death
associated with such unintended or unauthorized use, even if such claim alleges that SCILLC was negligent regarding the design or manufacture of the part. SCILLC is an Equal
Opportunity/Affirmative Action Employer. This literature is subject to all applicable copyright laws and is not for resale in any manner.

PUBLICATION ORDERING INFORMATION

LITERATURE FULFILLMENT: N. American Technical Support: 800−282−9855 Toll Free ON Semiconductor Website: http://onsemi.com
Literature Distribution Center for ON Semiconductor USA/Canada
P.O. Box 61312, Phoenix, Arizona 85082−1312 USA Order Literature: http://www.onsemi.com/litorder
Phone: 480−829−7710 or 800−344−3860 Toll Free USA/Canada Japan: ON Semiconductor, Japan Customer Focus Center
Fax: 480−829−7709 or 800−344−3867 Toll Free USA/Canada 2−9−1 Kamimeguro, Meguro−ku, Tokyo, Japan 153−0051 For additional information, please contact your
Email: orderlit@onsemi.com Phone: 81−3−5773−3850 local Sales Representative.

http://onsemi.com NCP1050/D
26