Mo Slurry Hose Systems - Brochure en 4868 03 23 en MNG

Integrated solution with extensive application expertise
Slurry hose systems

SLURRY HOSE SYSTEMS
Table of contents
The System……............................................................................................................................ 3
Rubber Hoses…. ................................................................................................................. .........3
Coupling & Gaskets ..................................................................................................................... 3
Material Handling Slurry Hose T40.............................................................................................. 4
Material Handling Slurry/Bulk Hose T60 ..................................................................................... 5
3xD Bends 90° .............................................................................................................................. 6
3xD Bends 45°…… ....................................................................................................................... 7
Couplings…… .............................................................................................................................. 8
Coated couplings ......................................................................................................................... 9
Gaskets….……... ........................................................................................................................ 10
Rubber Lined Steel Pipe ............................................................................................................ 11
Branch Pipes S45....................................................................................................................... 12
Branch Pipes K45 ...................................................................................................................... 13
Branch Pipes T90 ....................................................................................................................... 14
Branch Pipes TX90..................................................................................................................... 15
Clamps…..…............................................................................................................................... 16
Sliding Clamps… ....................................................................................................................... 17
Concentric Rubber Lined Steel Reducer .................................................................................. 18
Rubber Compensators............................................................................................................... 20
Flange standard EN1092-1 ……………………………………………………………………………... 21
Flange standard ANSI 150 ……………………………………………………………………………… 22
Connection type: Trellex coupling – TO – Trellex coupling ……………………………………… 23
Connection type: Trellex coupling – TO – Flange type 01 …………………………………...…... 24
Connection type: Trellex coupling – TO – Flange type 02/32 ……………………………………. 25
Connection type: Flange type 01 – TO – Flange type 02/32 ……………………………………… 26
© 2023 Metso Outotec
4868-03-23-EN-MNG
SLURRY HOSE SYSTEMS
The System
Metso Outotec Slurry Hose Systems are based on easily
exchangeable standard components: hoses, couplings and
gaskets of varying diameters. The figure to the right shows the
principle for Metso Outotec Slurry Hose Systems with support
beams. The beam is used as a support for hoses, bends and
couplings and is fixed to a steel frame and is screwed to the
floor. The hose is fixed to the beam using clamps, sized in
relation to the hose dimensions.
Metso Outotec slurry hose systems with support beams.
Rubber Hoses
Rubber slurry hoses are used for sections of slurry hose systems containing bends, differences in
levels and unevenness. The rubber hose is flexible and can be easily adjusted to different lengths,
to a certain degree, or bent to requirements. For the recommended bend radius, contact your local
Metso Outotec representative today.
Rubber Lined Steel Pipes
The rubber lined steel pipe is an alternative to the rubber hose for the straighter sections of the slurry
hose system. The rubber lined steel pipe is available in 3m &6m lengths. The rubber lined steel pipe
doesn’t need a support beam, it only requires support at each end. For other lengths contact your
local Metso Outotec representative.
Coupling & Gaskets

Aluminum couplings are placed between the hose lengths for fully tight joints and are reinforced with
rubber gaskets. The rubber seals compensate for the unevenness in the joints, while also protecting
the couplings from direct contact with the slurry. The same type of couplings and seals are used for
both rubber hoses and rubber3xD bends.
3xD Bends
Bends are used in tight spaces, where the smallest bend radius of the hose is not enough. It also is
possible to adjust bending angle to a certain degree.
Standards Specifications / Painting
According to PED EN 13480 Surface preparation blasting grade: Sa 2.5
According to EN3834. Primary Coat: EP (Zn (R)) 60/1
Flanges according to -EN1092-1 and ASME Top Coat: Pur 120/2

B16.5
Painting and surface treatment according to Painting system: EP (Zn (R)) PUR 180/3
EN ISO 12944-4, ISO 8501-1 and EN ISO
12944-5
4868-03-23-EN-MNG
SLURRY HOSE SYSTEMS
Material Handling Slurry Hose T40

Material handling hoses are used for slurry handling in the mineral processing industry, coal
refinement plants, power plants in the steel and cement industries and other applications where high
wear resistance, flexibility and vibration reduction are required.
Product description: Trellex Material Handling Slurry Hose for hydraulic applications. It has a wear
tube of natural rubber T40 marked with a green label.
Areas of use: Transport of extremely abrasive materials and slurries containing particles up to
10mm in size.
Characteristics: Thick, wear resistant tubes with smooth walls and low flow resistance. Together
with Trellex couplings and gaskets, these hoses form an extremely reliable system which retains the
free flow area without turbulence at the couplings.
Technical description: The hoses are reinforced with cord and have embedded galvanized steel
wire spirals for managing dynamic pressure and under pressure. Test pressure is 1.5 times the
working pressure and peak pressure against bursting 3.2 times working pressure. The hose can
withstand operating temperatures up to 60-70°C.
Installation: Trellex Material Handling Slurry Hoses are cut to length on site.
Part No. ID mm/ OD mm Standard length Wear tube Working Vacuum Bend radius Weight
inch m/ft mm inch pressure Rec. 10xID Min. kg/ lbs/
Mpa/psi
mm mm m ft
SH-27748 51/2 72 20/66 6 1/4 1.0/150 90 % 500 300 2.4 1.6
SH-27771 76/3 99.5 20/66 6 1/4 1.0/150 90 % 750 450 4.1 2.8
SH-27805 102/4 125 20/66 6 1/4 1.0/150 90 % 1000 600 5.4 3.7
SH-27821 127/5 154 20/66 6 1/4 1.0/150 90 % 1250 750 7.5 5.1
SH-227847 152/6 178 10/33 6 1/4 1.0/150 90 % 1500 900 8.9 6.1
SH-227888 204/8 238 10/33 7.5 5/16 1.0/150 90 % 2000 1300 16 11
SH-227904 254/10 291 10/33 7.5 5/16 1.0/150 50 % 2500 1600 21 15
SH-27912 305/12 341 10/33 7.5 5/16 1.0/150 50 % 3000 1800 27 18
SH-228162 355/14 403 10/33 12 1/2 0.5/75 50 % 3500 2200 41 28
SH-473538 405/16 456 10/33 12 1/2 0.5/75 50 % 4000 2500 46 32
SH-728170 457/18 507 10/33 10.5 7/16 0.5/75 50 % 4500 2900 55 38
SH-728188 508/20 558 10/33 12 1/2 0.5/75 50 % 5000 3100 64 44
SH-728196 610/24 664 10/33 12 1/2 0.5/75 50 % 6000 3700 88 60
4868-03-23-EN-MNG
SLURRY HOSE SYSTEMS
Material Handling Slurry/Bulk Hose T60

Material handling hoses are used for slurry and bulk handling in the mineral processing industry,
coal refinement plants, power plants in the steel and cement industries and other applications where
high wear resistance, flexibility and vibration reduction are required.
Product description: Trellex Material Handling Slurry/Bulk Hose T60 are made of SBR rubber T60
marked with a yellow label.
Areas of use: Pneumatic transport of dry bulk material or abrasive material over 10mm in size.
Characteristics: Thick, wear resistant tube with smooth walls and low flow resistance. Together
with Trellex couplings and gaskets, these hoses form an extremely reliable system which retains the
free flow area without turbulence at the couplings.
Technical description: The hoses are reinforced with cord and have embedded galvanized steel
wire spirals for managing dynamic pressure and under pressure. Test pressure is 1.5 times the
working pressure and peak pressure against bursting 3.2 times working pressure. The hose can
withstand operating temperatures up to 70-80°C.
Installation: Trellex Material Handling Slurry/Bulk Hoses are cut to length on site.
Part No. ID mm/ OD mm Standard length Wear tube Working Vacuum Bend radius Weight
inch m/ft mm inch pressure Rec 10xID Min kg/m lbs/ft
Mpa/psi mm mm
SH-509380 51/2 72 20/66 6 1/4 1.0/150 90 % 500 300 2.4 1.6
SH-509406 76/3 99.5 20/66 6 1/4 1.0/150 90 % 750 450 4.1 2.8
SH-509430 102/4 125 20/66 6 1/4 1.0/150 90 % 1000 600 5.4 3.7
SH-371278 127/5 154 20/66 6 1/4 1.0/150 90 % 1250 750 7.5 5.1
SH-373134 152/6 178 10/33 6 1/4 1.0/150 90 % 1500 900 8.9 6.1
SH-371260 204/8 238 10/33 7.5 5/16 1.0/150 90 % 2000 1300 16 11
SH-602318 254/10 291 10/33 7.5 5/16 1.0/150 50 % 2500 1600 21 15
SH-602300 305/12 341 10/33 7.5 5/16 1.0/150 50 % 3000 1800 27 18
SH-1625340 355/14 403 10/33 12 1/2 0.5/75 50 % 3500 2200 41 28
SH-489255 405/16 456 10/33 12 1/2 0.5/75 50 % 4000 2500 46 32
SH-489256 457/18 507 10/33 10.5 7/16 0.5/75 50 % 4500 2900 55 38
SH-489257 508/20 558 10/33 12 1/2 0.5/75 50 % 5000 3100 64 44
SH-602319 610/24 664 10/33 12 1/2 0.5/75 50 % 6000 3700 88 60
4868-03-23-EN-MNG
SLURRY HOSE SYSTEMS
3xD Bends 90°

3xD Bends 90° are used for slurry handling in heavy wear applications in the mining processing
industry, coal refinement plants, power plants in the steel and cement industries and other
applications where high wear resistance is required.
Product description: Trellex 3xD Bends are made completely of rubber, cord reinforcement and a
fully embedded galvanized steel wire spiral.
Areas of use: Intended for use in tight spaces where ordinary hoses cannot be bent enough. For
optimum wear economy, the outer bend has a >30 % thicker wear tube than the inner bend. Can be
bent between 60°-110°.
Characteristics: Thick rubber bends with smooth walls and low flow resistance.
Technical description: Test pressure is 1.5 times the working pressure and peak pressure against
bursting 3.2 times working pressure. Straight sections outside the 3xD bend allows connection with
couplings.
Installation: Quick & easy installation without special tools. Couplings & gaskets are not included.
Part No. ID OD Wear tube Operating pressure AxB C R Weight

Outer radius
mm inch mm mm inch MPa psi kg lbs
SH-179903 51 2 72 8 5/16 1.0 150 260 x 260 105 155 1.1 2.4
SH-35956 76 3 100 8 5/16 1.0 150 335 x 335 105 230 2.3 5.1
SH-35972 102 4 125 8 5/16 1.0 150 455 x 455 150 305 4.3 9.5
SH-371245 127 5 154 8 5/16 1.0 150 570 x 570 190 380 8.1 17.9
SH-36004 152 6 178 8 5/16 1.0 150 670 x 670 215 455 10.8 24
SH-36020 204 8 238 10 7/16 1.0 150 890 x 890 275 615 25.2 56
SH-588665 254 10 291 10 7/16 1.0 150 980 x 980 215 765 32.2 71
SH-371286 305 12 341 10 7/16 1.0 150 1170 x 1170 255 915 51 112
SH-2070150 355 14 403 16 5/8 0.5 75 1360 x 1360 295 1065 56.5 125
SH-1717550 405 16 456 16 5/8 0.5 75 1615 x 1615 400 1215 60 132
SH-371290 457 18 507 16 5/8 0.5 75 1871 x 1871 500 1371 80 176
SH-2880440 508 20 558 16 5/8 0.5 75 2020 x 2020 500 1520 110 242
SH-489184 610 24 664 16 5/8 0.5 75 2440 x 2440 605 1835 265 584
4868-03-23-EN-MNG
SLURRY HOSE SYSTEMS
3xD Bends 45°

3xD Bends 45° are used for slurry handling in heavy wear applications in the mining processing
industry, coal refinement plants, power plants in the steel and cement industries and other
applications where high wear resistance is required.
Product description: Trellex 3xD Bends are made completely of rubber, cord reinforcement and a
fully embedded galvanized steel wire spiral.
Areas of use: Intended for use in tight spaces where ordinary hoses can’t be bent enough. For
optimum wear economy, the outer bend has a >30 % thicker wear tube than the inner bend and can
be bent between 30°- 60°.
Characteristics: Thick bends with smooth walls and low flow resistance.
Technical description: Test pressure is 1.5 times the working pressure and peak pressure against
bursting 3.2 times working pressure. Straight sections outside the 3xD bend allows for connection
with couplings.
Installation: Quick & easy installation without special tools. Couplings & gaskets are not included.
Part No. ID OD Wear tube Operating pressure AxB C R Weight

Outer radius
mm inch mm mm inch MPa psi kg lbs
SH-179895 51 2 72 8 5/16 1.0 150 120 x 290 105 155 0.7 1.6
SH-35840 76 3 100 8 5/16 1.0 150 140 x 340 105 230 1.5 3.3
SH-35865 102 4 125 8 5/16 1.0 150 195 x 475 150 305 2.8 6.2
SH-371252 127 5 154 8 5/16 1.0 150 245 x 595 190 380 5.3 11.6
SH-35899 152 6 178 8 5/16 1.0 150 285 x 690 215 455 7 15.5
SH-35915 204 8 238 10 7/16 1.0 150 375 x 905 275 615 16.4 36
SH-588640 254 10 291 10 7/16 1.0 150 375 x 905 215 765 20.9 46
SH-588657 305 12 341 10 7/16 1.0 150 445 x 1075 255 915 33.2 73
SH-489185 355 14 403 16 5/8 0.5 75 520 x 1255 295 1065 36.7 81
SH-489186 405 16 456 16 5/8 0.5 75 640 x 1540 400 1215 39 86
SH-489187 457 18 507 16 5/8 0.5 75 755 x 1823 500 1371 52 115
SH-489188 508 20 558 16 5/8 0.5 75 800 x 1930 500 1520 71.5 158
SH-489189 610 24 664 16 5/8 0.5 75 965 x 2330 605 1835 172.3 380
4868-03-23-EN-MNG
SLURRY HOSE SYSTEMS
Couplings
Couplings are designed for use with hoses, bends and rubber lined steel pipes for slurry handling in
heavy wear applications.
Product description: Trellex split flange couplings are made of high strength aluminum alloys. They
consist of 2 or 4 identical segments which are mounted mechanically on the smooth hose.
Areas of use: Pumping of extremely abrasive materials.
Characteristics: The couplings are reusable after replacing hoses since they do not come into
contact with the transported materials.
Technical description: Trellex Couplings comply with DIN and ANSI flange standard.
Installation: The couplings don’t need to be suited to any special pattern on the hose cover. It is
simply twisted around the hose until it fits into the connected flange.
Part No. Coupling Dimension ExF mm Holes per Sections Matches flange Operating Weight
size mm/ joint per pressure
A B C G EN1092-1 ANSI B16.5 kg lbs
inch segment PN 10 150 lbs mpa / psi
mm mm mm mm
SH-27946 51/2 165 124 91 18 18x20 2 2 50 2” 1.0/150 1.8 4.0
SH-27961 76/3 200 158 91 20 18x24 2 2 80 3” 1.0/150 2.4 5.5
SH-27995 102/4 220 184 133 20 18x24 3 2 100 4” 1.0/150 3.5 7.7
SH-28019 127/5 250 213 165 22 23x26 3 2 125 5” 1.0/150 4.8 10.6
SH-28035 152/6 285 238 197 22 23x27 3 2 150 6” 1.0/150 6.2 13.6
SH-28076 204/8 340 295 257 24 23x26 3 2 200 8” 1.0/150 10.6 23
SH-228092 254/10 405 353 197 25 25x33 5 2 250 10” 1.0/150 11 24
SH-228100 305/12 495 418 237 25 25x47 5 2 300 12” 1.0/150 21 47
SH-28118 355/14 530 455 277 25 27x40 3 4 350 - 0.5/75 26 56
SH-657536 1355/14* 530 466 277 25 28x41 2 4 - 14” 0.5/75 27 59
SH-28126 405/16 600 521 400 25 27x51 3 4 400 16” 0.5/75 45 100
SH-657544 457/18 634 556 450 25 27x36 4 4 450 - 0.5/75 50 110
SH-657551 1457/18* 634 569 450 25 27x36 3 4 - 18” 0.5/75 51 113
SH-657569 508/20 698 621 500 25 27x44 4 4 500 20” 0.5/75 62 136
SH-657577 610/24 820 731 600 30 30x52 4 4 600 24” 0.5/75 80 175
4868-03-23-EN-MNG
SLURRY HOSE SYSTEMS
Coated couplings
Coated Couplings are designed for use with hoses, bends and rubber lined steel pipes for slurry
handling in a corrosive environment like salt mines.
Product description: Trellex split flange coated couplings are made of high strength aluminum
alloys and a thermoplastic coating. The couplings consist of two or four identical segments which
are mounted mechanically on the smooth hose.
Areas of use: Pumping of extremely abrasive materials in a corrosive environment like salt
production and diluted acid.
Characteristics: The couplings are reusable after replacing hoses, since they do not come into
contact with the transported materials.
Technical description: Trellex Couplings comply with DIN and ANSI flange standard.
Thermoplastic coating that protects the aluminum from corrosion in hazard environment. Fasteners
and grater plate comes in stainless steel.
Installation: The couplings do not need to be suited to any special pattern on the hose cover. It is
simply twisted around the hose until it fits into the flange connected.
Part No. Coupling Dimension ExF mm Holes per Sections Matches flange Operating Weight
size mm/ A B C G joint per EN1092-1 ANSI B16.5 pressure kg lbs
inch segment PN 10 150 lbsMPa/ psi
mm mm mm mm
SH-27946-C 51/2 165 124 91 18 18x20 2 2 50 2” 1.0/150 1.8 4.0
SH-27961-C 76/3 200 158 91 20 18x24 2 2 80 3” 1.0/150 2.4 5.5
SH-27995-C 102/4 220 184 133 20 18x24 3 2 100 4” 1.0/150 3.5 7.7
SH-28019-C 127/5 250 213 165 22 23x26 3 2 125 5” 1.0/150 4.8 10.6
SH-28035-C 152/6 285 238 197 22 23x27 3 2 150 6” 1.0/150 6.2 13.6
SH-28076-C 204/8 340 295 257 24 23x26 3 2 200 8” 1.0/150 10.6 23
SH-228092-C 254/10 405 353 197 25 25x33 5 2 250 10” 1.0/150 11 24
SH-228100-C 305/12 495 418 237 25 25x47 5 2 300 12” 1.0/150 21 47
SH-28118-C 355/14 530 455 277 25 27x40 3 4 350 - 0.5/75 26 56
SH-657536-C 1355/14* 530 466 277 25 28x41 2 4 - 14” 0.5/75 27 59
SH-28126-C 405/16 600 521 400 25 27x51 3 4 400 16” 0.5/75 45 100
SH-657544-C 457/18 634 556 450 25 27x36 4 4 450 - 0.5/75 50 110
SH-657551-C 1457/18* 634 569 450 25 27x36 3 4 - 18” 0.5/75 51 113
SH-657569-C 508/20 698 621 500 25 27x44 4 4 500 20” 0.5/75 62 136
SH-657577-C 610/24 820 731 600 30 30x52 4 4 600 24” 0.5/75 80 175
4868-03-23-EN-MNG
SLURRY HOSE SYSTEMS
Gaskets
Gaskets are designed for use with couplings, together with hoses, bends and rubber lined steel pipes
for slurry handling in heavy wear applications.
Product description: The conical Trellex Gasket is designed for use together with Trellex hoses,
bends and rubber lined steel pipes. Together with the Trellex Coupling, the gasket ensures
completely sealed couplings while retaining full inner diameter.
Characteristics: Steel reinforced gaskets that allows for turbulence free passage. The inner
diameter is the same size as the hose and the conical shape compensates for irregularities in the
hose ends. Grooves at the front eliminate the risk of leaks.
Other information: Two couplings and two gaskets are required to form a complete link between
two hoses. Secure sealing band for an easy installation and as a leak proof solution.
Part No. For internal hose diameter Weight

mm inch kg lbs
SH-373977 51 2” 0.06 0.15

SH-373951 76 3” 0.10 0.20
SH-373928 102 4” 0.15 0.30
SH-373902 127 5” 0.20 0.40

SH-373886 152 6” 0.25 0.60
SH-373852 204 8” 0.40 0.90
SH-373837 254 10” 0.60 1.30
SH-373829 305 12” 0.70 1.50

SH-373811 355 14” 0.75 1.60
SH-373803 405 16” 0.90 1.90
SH-373795 457 18” 1.00 2.20

SH-373787 508 20” 1.20 2.80
SH-373779 610 24” 1.70 3.80
4868-03-23-EN-MNG
SLURRY HOSE SYSTEMS
Rubber Lined Steel Pipe

Rubber lined steel pipes are used in the mining processing industry, coal refinement plants, power
plants in the steel, cement industries & other applications where high wear resistance is required.
Product description: Trellex Rubber Lined Steel Pipes for hydraulic applications are lined with a
natural rubber of quality Trellex T50.
Characteristics: Rigid steel pipes with smooth rubber

lined walls and low flow resistance. One fixed and one
rotating flange with inbuilt gasket. It forms a reliable
system that retains the free flow area without turbulence.
Technical description: Steel pipes lined with natural

rubber. The safety factor is 1.5 times the working
pressure.
ID Length Wear Tube Flange drilling Operating Pressure Weight

Part No. EN1092-1/
mm inch m ft mm inch MPa psi kg lbs
ANSI B.16.5
DIN PN10 Flange
489933-102-3000 102 4 3 10 5 0.2 100 1.0 150 45 99
489933-102-6000 102 4 6 20 5 0.2 100 1.0 150 79 175
489933-127-3000 127 5 3 10 5 0.2 125 1.0 150 59 131
489933-127-6000 127 5 6 20 5 0.2 125 1.0 150 106 233
489933-152-3000 152 6 3 10 5 0.2 150 1.0 150 79 175
489933-152-6000 152 6 6 20 5 0.2 150 1.0 150 141 311
489933-204-3000 204 8 3 10 5 0.2 200 1.0 150 104 228
489933-204-6000 204 8 6 20 5 0.2 200 1.0 150 185 408
489933-254-3000 254 10 3 10 5 0.2 254 1.0 150 140 309
489933-254-6000 254 10 6 20 5 0.2 250 1.0 150 252 555
489933-305-3000 305 12 3 10 5 0.2 300 1.0 150 168 370
489933-305-6000 305 12 6 20 5 0.2 300 1.0 150 326 719
ASME B16.5 150lbs Flange

489934-102-3000 102 4 3 10 5 0.2 4’’ 1.0 150 45 99
489934-102-6000 102 4 6 20 5 0.2 4’’ 1.0 150 79 175
489934-127-3000 127 5 3 10 5 0.2 5’’ 1.0 150 59 131
489934-127-6000 127 5 6 20 5 0.2 5’’ 1.0 150 106 233
489934-152-3000 152 6 3 10 5 0.2 6’’ 1.0 150 79 175
489934-152-6000 152 6 6 20 5 0.2 6’’ 1.0 150 141 311
489934-204-3000 204 8 3 10 5 0.2 8’’ 1.0 150 104 228
489934-204-6000 204 8 6 20 5 0.2 8’’ 1.0 150 185 408
489934-254-3000 254 10 3 10 5 0.2 10’’ 1.0 150 140 309
489934-254-6000 254 10 6 20 5 0.2 10’’ 1.0 150 252 555
489934-305-3000 305 12 3 10 5 0.2 12’’ 1.0 150 168 370
489934-305-6000 305 12 6 20 5 0.2 12’’ 1.0 150 326 719
Installation: Trellex Rubber Lined Steel Pipe have fixed lengths & are designed to be used together
with Slurry Hose System on straight sections. Gasket included in flange.
4868-03-23-EN-MNG
SLURRY HOSE SYSTEMS
Branch Pipes S45

Branch pipes are used in the mining processing industry, coal refinement plants, power plants in the
steel and cement industries and other applications where high wear resistance is required.
Product description: Trellex Branch Pipes S45 are lined with a natural rubber of Trellex T50.
Characteristics: Rigid steel pipes with smooth rubber lined walls and low flow resistance. It forms
a reliable system that retains the free flow area without turbulence at the couplings.
Technical description: High strength steel pipes lined with natural rubber. The safety factor is 1.5
times the working pressure. Wear tube up to 10mm depending on dimension. Combined Flange
drilling according to DIN PN10 and ASME 150lbs flange standard.
Installation: Trellex Branch Pipes S45 are available in dimensions according to the table below.
Gasket included in flange
ID Wear Tube A B Operating pressure Combined flange Weight Y45

mm inch mm inch mm mm MPa psi drilling Kg lbs
Part No
EN 1092 PN10 / ANSI
B16. 150lbs
SH-574943 51 2 3 0.12” 146.4 53.0 1.0 150 50 / 2” 10 22
SH-968198 76 3 3 0.12” 146.4 72.0 1.0 150 80 / 3” 14 31
SH-574947 102 4 10 0.4’’ 148.4 74.0 1.0 150 100 / 4” 16 35
SH-574954 127 5 10 0.4’’ 173.8 88.0 1.0 150 125 / 5” 25 55
SH-574962 152 6 10 0.4’’ 195.0 98.0 1.0 150 150 / 6” 30 66
SH-574970 204 8 10 0.4’’ 261.5 133.0 1.0 150 200 / 8” 49 108
SH-574988 254 10 10 0.4’’ 317.7 159.0 1.0 150 250 / 10” 68 150
SH-574996 305 12 10 0.4’’ 374.1 190.0 1.0 150 300 / 12” 115 253
SH-1533120 355 14 10 0.4’’ 447.6 225.0 1.0 150 350 / 14” 120 264
SH-489936-405 405 16 10 0.4’’ 474.3 250.0 1.0 150 400 / 16” 150 330
SH-489936-457 457 18 10 0.4’’ 495.0 300.0 1.0 150 450 / 18” 175 385
SH-489936-508 508 20 10 0.4’’ 565.7 350.0 1.0 150 500 / 20” 199 439
SH-489936-610 610 24 10 0.4’’ 636.4 350.0 1.0 150 600 / 24” 224 493
4868-03-23-EN-MNG
SLURRY HOSE SYSTEMS
Branch Pipes K45

Product description: Trellex Branch Pipes K45 are lined with a natural rubber of Trellex T50. The
pipes are customized to fit Trellex couplings.
Areas of use: Pumping of extremely abrasive materials
Characteristics: Rigid steel pipes with smooth rubber lined walls and low flow resistance. The
special components are based on Trellex pipes together with Trellex couplings and sealings. It forms
a reliable system that retains the free flow area without turbulence at the couplings.
Technical description: High strength steel pipes lined with natural rubber. The safety factor is 1.5
times the working pressure. 5mm wear tube up to inner diameter 305mm, and 10mm wear tube from
355 to 610mm. Combined Flange drilling according to DIN PN10 and ANSI 150lbs flange standard.
Installation: Trellex Branch Pipes K45 are available in dimensions according to table below. For
diameter change, use rubber lined reducers. Gasket included in flange.
Part No. ID D1 A B Wear Operating Combined flange Weight
tube Pressure drilling
mm inch mm mm mm MPa EN 1092 PN10 / kg lbs
ANSI B16 150lbs
SH-489871-51-51 51 2 300 250 3 1.0 50 / 2” 10.6 23.5
SH-489871-76-76 76 3 400 300 3 1.0 80 / 3” 15.9 35.1
SH-489871-102-102 102 4 400 300 10 1.0 100 / 4” 17.4 38.3
SH-489871-127-127 127 5 450 350 10 1.0 125 / 5” 27.1 59.8
SH-489871-152-152 152 6 500 400 10 1.0 150 / 6” 34.3 75.7
SH-489871-204-204 204 8 650 500 10 1.0 200 / 8” 61.2 135.0
SH-489871-254-254 254 10 550 550 10 1.0 250 / 10” 93.5 206.1
SH-489871-305-305 305 12 800 650 10 1.0 300 / 12” 130.3 287.2
SH-489871-355-355 355 14 900 700 10 1.0 350 / 14” 144.0 317.4
SH-489871-405-405 405 16 1000 800 10 1.0 400 / 16” 178.3 393.1
SH-489871-457-457 457 18 1200 900 10 1.0 450 / 18” 288.4 635.9
SH-489871-508-508 508 20 1350 1000 10 1.0 500 / 20” 348.9 769.2
SH-489871-610-610 610 24 1600 1200 10 1.0 600 / 24” 550.6 1213.9
For other size combinations, please contact your local Metso Outotec representative.
4868-03-23-EN-MNG
SLURRY HOSE SYSTEMS
Branch Pipes T90

Product description: Trellex Branch Pipes T90 are lined with a natural rubber of Trellex T50.
Characteristics: Rigid steel pipes with smooth rubber lined walls and low flow resistance. The
special components are based on Trellex Pipes with split steel flanges. The branch pipes form a
reliable system which retains the free flow area without turbulence at the flanges.
Technical description: High strength steel pipes lined with natural rubber. Fixed steel flanges with
inbuilt rubber gasket. The safety factor is 1.5 times the working pressure. 10 mm wear tube from ID
102mm. Combined Flange drilling according to DIN PN10 and ANSI 150lbs flange standard.
Installation: Trellex Branch Pipes are available in dimensions according to table below.
Item code: SH-489818-D1-D2
T1 T2 Combined Flange Drilling

Operating
Part no. D1 L1 Wear D2 L2 Wear EN 1092 PN10 / ANSI B16. 150 Weight
Pressure
tube tube lbs
mm mm mm mm mm mm mpa psi D1 D2 kg lbs
SH-489818-51-51 51 380 3 51 105 3 1.0 150 50 / 2” 50 / 2” 10.6 23.4
SH-489818-76-76 76 380 3 76 120 3 1.0 150 80 / 3” 80 / 3” 14.9 33.1
SH-489818-102-76 102 380 10 76 139 3 1.0 150 100 / 4” 80 / 3” 16.1 35.5
SH-489818-127-76 127 380 10 76 152 3 1.0 150 125 / 5” 80 / 3” 18.7 41.2
SH-489818-152-76 152 380 10 76 166 3 1.0 150 150 / 6” 80 / 3” 25.8 56.9
SH-489818-204-102 204 380 10 102 192 10 1.0 150 200 / 8” 100 / 4” 35.6 78.6
SH-489818-254-102 254 380 10 102 217 10 1.0 150 250 / 10” 100 / 4” 42.9 94.7
SH-489818-305-102 305 380 10 102 243 10 1.0 150 300 / 12” 100 / 4” 56.1 123.7
SH-489818-355-102 355 380 10 102 268 10 1.0 150 350 / 14” 100 / 4” 70.6 155.7
SH-489818-405-152 405 570 10 152 318 10 1.0 150 400 / 16” 150 / 6” 96.1 211.9
SH-489818-457-152 457 570 10 152 344 10 1.0 150 450 / 18” 150 / 6” 124.9 275.3
SH-489818-508-152 508 570 10 152 369 10 1.0 150 500 / 20” 150 / 6” 142.4 313.9
SH-489818-610-204 610 570 10 204 420 10 1.0 150 600 / 24” 200 / 8” 179.9 396.6
4868-03-23-EN-MNG
SLURRY HOSE SYSTEMS
Branch Pipes TX90

Branch pipes are used in the mining processing industry, coal refinement plants, power plants in
the steel and cement industries and other applications where high wear resistance is required.
Product description: Trellex Branch Pipes TX90 are lined with a natural rubber of Trellex T50.
Characteristics: Rigid steel pipes lined with long-life wear rubber with smooth walls and low flow
resistance. These branch pipes form an extremely reliable system which retains the free flow area
without turbulence at the flanges.
Technical description: High strength steel pipes lined with natural rubber. Fixed steel flanges with
inbuilt rubber gasket. The safety factor is 1.5□times the working pressure. 10 mm wear tube from ID
102mm. Combined Flange drilling according to DIN PN10 and ASME 150lbs flange standard.
Installation: Trellex Branch Pipes are available in dimensions according to the table below.
Item code: SH-489797-D1-D2
T1 T2
Operating Combined Flange Drilling
D1 L1 Wear D2 L2 Wear D3 L3 Weight
Part no. Pressure EN 1092 PN10 / ANSI B16. 150 lbs
tube tube
mm mm mm mm mm mm mm mm mpa psi D1 D2 D3 kg lbs
SH-489797-51-51 51 380 3 51 105 3 51 105 1.0 150 50 / 2” 50 / 2” 50 / 2” 13,8 30,5
SH-489797-76-76 76 380 3 76 120 3 51 120 1.0 150 80 / 3” 80 / 3” 50 / 2” 18,2 40,2
SH-489797-102-76 102 380 10 76 139 3 51 139 1.0 150 100 / 4” 80 / 3” 50 / 2” 19,1 42,2
SH-489797-127-76 127 380 10 76 152 3 51 152 1.0 150 125 / 5” 80 / 3” 50 / 2” 21,6 47,6
SH-489797-152-76 152 380 10 76 166 3 51 166 1.0 150 150 / 6” 80 / 3” 50 / 2” 27,9 61,5
SH-489797-204-102 204 380 10 102 192 10 76 192 1.0 150 200 / 8” 100 / 4” 80 / 3” 40,5 89,2
SH-489797-254-102 254 380 10 102 217 10 76 217 1.0 150 250 / 10” 100 / 4” 80 / 3” 47,3 104,8
SH-489797-305-102 305 380 10 102 243 10 76 243 1.0 150 300 / 12” 100 / 4” 80 / 3” 60,2 132,8
SH-489797-355-102 355 380 10 102 268 10 102 268 1.0 150 350 / 14” 100 / 4” 100 / 4” 72,5 160,3
SH-489797-405-152 405 570 10 152 318 10 102 293 1.0 150 400 / 16” 150 / 6” 100 / 4” 98.2 215,3
SH-489797-457-152 457 570 10 152 344 10 102 319 1.0 150 450 / 18” 150 / 6” 100 / 4” 125,7 277,2
SH-489797-508-152 508 570 10 152 369 10 102 344 1.0 150 500 / 20” 150 / 6” 100 / 4” 142,6 314,5
SH-489797-610-204 610 570 10 204 420 10 152 420 1.0 150 600 / 24” 200 / 8” 150 / 6” 183.0 403,5
For other size combinations, please contact your local Metso Outotec representative.
4868-03-23-EN-MNG
SLURRY HOSE SYSTEMS
Clamps
Clamps are used to mount material handling hoses and rubber lined steel pipes in the mineral
processing industry, coal refinement plants, power plants and cement factories.
Product description: Clamps are made of galvanized steel.
Area of use: Steel clamps are used to fix hoses or pipes to the support beam. It is important for the
hose to be fixed to the supporting beam at bends & wherever long lengths of hoses are used.
Characteristics: Clamping is done every 1000 to 1500 mm in a straight line on both vertical and
horizontal layouts. In curved sections, tighter clamping is recommended.
Technical description: Clamps are made of galvanized steel & correspond to SSG 7075 standard.
Installation: Clamps are available in sizes Hose / Pipe ID Spacing Hose Distance to
pipe end
matching the size of hoses and pipes, see table mm / inch mm / ft mm / ft
below left. The following spacing between each 51-127 / 2-5 1000 / 3 300 / 1
152-355 / 6-14 1250 / 4 500 / 1.5
clamp is recommended: 405-610 / 16-24 1500 / 5 1000 / 3
Rubber Strip (SH-489245): To clamp rubber lined steel pipes use Rubber Strip (SH-489245) as
spacer. Strip needs to be ordered separately. Needed length for each clamp, see tables below:
Part no. Hose / Pipe ID Clamp Width Total Weight Screw Dim. (not included) Pipe ID Length (rubber strip)
mm inch mm inch kg lbs Metric inch mm inch mm inch
SH-596551 51 2 40 1.6 0.5 1.1 M10x40 3/8 x 1.6” 51 2 250 10
SH-596577 76 3 50 2 1.4 3.1 M10x40 3/8 x 1.6” 76 3 350 14
SH-575043 102 4 50 2 1.6 3.5 M16x60 5/8 x 2.4” 102 4 450 18
SH-575050 127 5 50 2 1.8 4 M16x60 5/8 x 2.4” 127 5 500 20
SH-575068 152 6 50 2 2 4.4 M16x80 5/8 x 2.4” 152 6 650 26
SH-575076 204 8 60 2.4 4.2 9.3 M20x80 3/4 x 3.2” 204 8 800 32
SH-575084 254 10 60 2.4 4.9 10.8 M20x80 3/4 x 3.2” 254 10 1000 39
SH-575092 305 12 60 2.4 5.5 12.1 M20x80 3/4 x 3.2” 305 12 1200 47
SH-602904 355 14 70 2.8 9.3 20.5 M20x80 3/4 x 3.2” 355 14 1300 51
SH-602896 405 16 70 2.8 10.1 22.3 M20x80 3/4 x 3.2” 405 16 1500 59
SH-602888 457 18 70 2.8 11 24.3 M20x80 3/4 x 3.2” 457 18 1600 63
SH-602870 508 20 100 4 20.2 44.5 M24x100 1 x 4” 508 20 2x1800 2x71
SH-602862 610 24 100 4 23.4 51.6 M24x100 1 x 4” 610 24 2x2100 2x83
4868-03-23-EN-MNG
SLURRY HOSE SYSTEMS
Sliding Clamps
Sliding clamps are used to mount rubber lined steel pipes in the mineral processing industry, coal
refinement plants, power plants and cement factories.
Product description: Sliding clamps are made of galvanized steel.
Area of use: Sliding clamps are used to fix pipes to the support beam. It is important that rubber
lined steel pipes have the ability to move due to temperature variations.
Characteristics: Clamping should be done at each pipe end. For 10m pipes three sliding clamps
might be necessary for high density media transportation.
Technical description: Sliding clamps are made of galvanized steel and correspond to SSG
standards.
Pipe ID Distance to pipe end
Installation: Mount sliding clamps at the distances mm / inch mm / ft
recommended below to the pipe end due to space 51-127 / 2-5 300/1
needed for couplings. Sliding clamps come without 152-355 / 6-14 500/1.5
405-610 / 16-24 1000/3
mounting screws, see recommended dimensions:
Rubber Strip (SH-489245): To clamp rubber lined steel pipes

use Rubber Strip (SH-489245) as spacer. Strip needs to be
ordered separately. Needed length for each clamp, see tables
below:
Clamps Rubber Strip

Part no. Hose/ Length Height Clamp Total Weight Screw Dim. Pipe Length
Pipe ID Width (not included) ID (rubber strip)
mm inch L h H b kg lbs Metric UNC mm inch mm inch
SH-489348-102 102 4 200 86 152 50 3.2 7 M16x60 5/8 x 2.4” 102 4 450 18
SH-489348-127 127 5 200 86 164 50 3.6 8 M16x60 5/8 x 2.4” 127 5 500 20
SH-489348-152 152 6 200 86 176 50 4 8.8 M16x80 5/8 x 2.4” 152 6 650 26
SH-489348-204 204 8 300 82 205 60 8.4 18.6 M20x80 3/4 x 3.2” 204 8 800 32
SH-489348-254 254 10 300 82 227 60 9.8 21.6 M20x80 3/4 x 3.2” 254 10 1000 39
SH-489348-305 305 12 300 83 253 60 11 24.2 M20x80 3/4 x 3.2” 305 12 1200 47
SH-489348-355 355 14 400 85 290 70 18.6 41 M20x80 3/4 x 3.2” 355 14 1300 51
SH-489348-405 405 16 400 85 315 70 20.2 44.6 M20x80 3/4 x 3.2” 405 16 1500 59
SH-489348-457 457 18 400 85 340 70 22 48.6 M20x80 3/4 x 3.2” 457 18 1600 63
SH-489348-508 508 20 400 85 366 100 40.4 89 M24x100 1 x 4” 508 20 2 x 1800 2 x 71
SH-489348-610 610 24 400 85 415 100 46.8 103.2 M24x100 1 x 4” 610 24 2 x 2100 2 x 83
4868-03-23-EN-MNG
SLURRY HOSE SYSTEMS
Concentric Rubber Lined Steel Reducer

Rubber lined steel reducers provide a transition between pipes or hoses of different diameters to
compensate for changes in flow velocity.
Product description: Trellex Rubber Lined Steel Reducers are fabricated from rolled and welded
steel sheets, lined with T50 rubber.
Characteristics: Steel reducers lined with 10 mm smooth rubber walls and low flow resistance.
Technical description: The safety factor is 1.5 times the working pressure. Taper of less than 2x8°
ensures smooth flow with no turbulence. Working pressure of 1.0 Mpa.
Installation: Combined flanges according to EN1092-1 PN10 and ANSI B16.5 150 lbs. Gasket
included in flange.
For Special Pump Reducers that fit pump flange drilling and are made to order, please contact your
local Metso Outotec representative.
4868-03-23-EN-MNG
SLURRY HOSE SYSTEMS
ID id Dy HC dy hc Length Weight
EN1092-1 ANSI B16.5 EN1092-1 ANSI B16.5
Item code
mm PN10, 150 lbs, mm PN10 , 150 lbs, mm kg lbs
mm mm mm mm
SH-489922 65 51 185 125 121 165 125 121 380 8 18
SH-489929 76 51 200 160 152 165 125 121 380 8 18
SH-489345 76 65 200 160 152 185 145 140 380 9 20
SH-489948 102 51 220 180 191 165 125 121 380 11 24
SH-489361 102 65 220 180 191 185 145 140 380 12 26
SH-489132 102 76 220 180 191 200 160 152 380 13 29
SH-489420 127 76 250 210 216 200 160 152 380 15 33
SH-489133 127 102 250 210 216 220 180 191 380 16 36
SH-489134 152 102 285 240 241 220 180 191 380 18 40
SH-489847 152 76 285 240 241 200 160 152 380 17 37
SH-489135 152 127 285 240 241 250 210 216 380 20 45
SH-489421 204 102 340 295 299 220 180 191 380 22 49
SH-489136 204 127 340 295 299 250 210 216 380 24 54
SH-489137 204 152 340 295 299 285 240 241 380 26 58
SH-489138 254 152 395 350 362 285 240 241 380 31 67
SH-489139 254 204 395 350 362 340 295 299 380 34 76
SH-489140 305 204 470 400 432 340 295 299 380 38 83
SH-489141 305 254 470 400 432 395 350 362 380 42 92
SH-489681 355 204 520 460 476 340 295 299 570 55 121
SH-489142 355 254 520 460 476 395 350 362 380 48 105
SH-489143 355 305 520 460 476 470 400 432 380 51 112
SH-489144 405 305 580 515 540 470 400 432 380 59 130
SH-489145 405 355 580 515 540 520 460 476 380 64 142
SH-489146 457 355 630 565 578 520 460 476 380 73 161
SH-489147 457 405 630 565 578 580 515 540 380 80 177
SH-489148 508 405 690 620 635 580 515 540 380 87 191
SH-489149 508 457 690 620 635 630 565 578 380 94 207
SH-489896 610 457 805 725 749 630 565 578 570 101 222
SH-489150 610 508 805 725 749 690 620 635 380 116 256
4868-03-23-EN-MNG
SLURRY HOSE SYSTEMS
Rubber Compensators
Rubber compensators are used to eliminate vibrations, noise, compensate for misalignments and
length deviations when rubber hose or rubber reducers are not used.
Product description: Trellex Rubber Compensators are made all of rubber reinforced with cord and
a steel spiral.
Areas of use: Typically used for flexibility between sump and pump. Flexibility is necessary at
suction side of pump for disassembly during maintenance.
Characteristics: A rubber compensator with split steel flanges that combines elastic properties of
rubber with various types of reinforcements to provide a flexible pipe joint.
Technical description: Working pressure is 10 bar/150 Psi & the safety factor is 1.5 times working
pressure. Lateral movement is 5 mm up to ID 102mm and 10mm for ID 127 to ID 610mm. Angular
movement is 3° for all dimensions.
Installation: Combined Flange drilling according to DIN PN10 and ASME 150lbs flange standard.
Two exceptions are for ID355 and ID457 where flanges are different.
Permissible Operating
ID Length Weight inc. Flanges
movements (mm) pressure
Item code Vacuum
mm inch mm Comp- Elon-
Lateral Angular MPa psi kg lbs
ression gation
SH-489299-51-F 51 2 200 2 2 5 3° 90 % 1.0 150 4.3 9.5
SH-489299-76-F 76 3 200 2 2 5 3° 90 % 1.0 150 4.3 9.5
SH-489299-102-F 102 4 200 2 2 5 3° 90 % 1.0 150 4.3 9.5
SH-489299-127-F 127 5 200 2 2 10 3° 90 % 1.0 150 5.8 12.8
SH-489299-152-F 152 6 250 2.5 2.5 10 3° 90 % 1.0 150 7.3 16.1
SH-489299-204-F 204 8 250 2.5 2.5 10 3° 90 % 1.0 150 10.0 22.0
SH-489299-254-F 254 10 250 2.5 2.5 10 3° 50 % 1.0 150 13.9 30.6
SH-489299-305-F 305 12 250 2.5 2.5 10 3° 50 % 1.0 150 16.0 35.3
SH-489299-355-F - 14 250 2.5 2.5 10 3° 50 % 1.0 150 20.9 46.1
SH-489299-1355-F 355 14 250 2.5 2.5 10 3° 50 % 1.0 150 20.9 46.1
SH-489299-405-F 405 16 250 2.5 2.5 10 3° 50 % 1.0 150 29.3 64.6
SH-489299-457-F 457 18 300 3 3 10 3° 50 % 1.0 150 33.7 74.3
SH-489299-1457-F - 18 300 3 3 10 3° 50 % 1.0 150 33.7 74.3
SH-489299-508-F 508 20 300 3 3 10 3° 50 % 1.0 150 42.8 94.4
SH-489299-610-F 610 24 300 3 3 10 3° 50 % 1.0 150 56.0 124
4868-03-23-EN-MNG
SLURRY HOSE SYSTEMS
Flange standard EN1092-1
Matching flange drilling according to EN1092-1 PN10
Flange size Bolting

ØK ØL ØD
mm Number Size
50 125 18 4 M16 165
80 160 18 8 M16 200
100 180 18 8 M16 220
125 210 18 8 M16 250
150 240 22 8 M20 285
200 295 22 8 M20 340
250 350 22 12 M20 395
300 400 22 12 M20 445
350 460 22 16 M20 505
400 515 26 16 M24 565
450 565 26 20 M24 615
500 620 26 20 M24 670
600 725 30 20 M27 780
4868-03-23-EN-MNG
SLURRY HOSE SYSTEMS
Flange standard ANSI 150
Matching flange drilling according to ANSI/ ASME B16.5 Class 150
Flange size Bolting

ØK ØL ØD
inch Number Size
2´´ 120,7 ¾´´ 4 5/8´´ 150
3´´ 152,4 ¾´´ 4 5/8´´ 190
4´´ 190,5 ¾´´ 8 5/8´´ 230
5´´ 215,9 7/8´´ 8 ¾´´ 255
6´´ 241,3 7/8´´ 8 ¾´´ 280
8´´ 298,5 7/8´´ 8 ¾´´ 345
10´´ 362,0 1´´ 12 7/8´´ 405
12´´ 431,8 1´´ 12 7/8´´ 485
14’’ 476,3 1 1/8´´ 12 1´´ 535
16´´ 539,8 1 1/8´´ 16 1´´ 595
18´´ 577,9 1 ¼´´ 16 1 1/8´´ 635
20´´ 635,0 1 ¼´´ 20 1 1/8´´ 700
24´´ 749,3 1 3/8´´ 20 1 ¼´´ 815
4868-03-23-EN-MNG
SLURRY HOSE SYSTEMS
Connection type: Trellex coupling – TO – Trellex coupling
Recommended fasteners Metric

Screw: SCREW HEX ISO4017-DIM x L-8.8-TZN HEX Screw Fully Threaded Hot dip Galvanized
Nut: NUT HEX ISO4032-DIM-8-A3A Nut Hot dip Galvanized
Washer: PLAIN WASHER ISO7089-DIM-200HV-A3A Washer Hot dip Galvanized
Recommended fasteners UNC

Screw: STUD BOLT ASME B18.2.1 DIM - L, A193 B7, Zinc plated Stud Bolt, ASTM A193, GR B7, Fully Threaded, Zinc plated
Nut: NUT HEX ASME B18.2.2 DIM, A194 2H, Zinc plated Hex Nut, ASTM A194, GR 2H, Zinc plated
Washer: PLAIN WASHER ASME B18.21.1-DIM-200HV, Zinc plated Plain Washer, Hardness 200HV, Zinc plated
ID Totally Dim Bolt Minimum Dim Minimum Stud Bolt ASME

mm fasteners per ISO 4017 Hex ISO 4017 Stud Bolt B18.2.1 length
joint, bolt length, ASME B18.2.1 mm
ISO/ASME mm
51 4 M16 120 5/8" 120
76 4 M16 120 5/8" 120
102 6 M16 120 5/8" 120
127 6 M16 120 3/4" 140
152 6 M20 120 3/4" 140
204 6 M20 120 3/4" 140
254 10 M20 120 7/8" 140
305 10 M20 120 7/8" 140
355 12/8 M20 120 1" 140
405 12 M24 140 1" 140
457 16/12 M24 140 1" 140
508 16 M24 140 1" 140
610 16 M27 140 1 1/8'' 160
4868-03-23-EN-MNG
SLURRY HOSE SYSTEMS
Connection type: Trellex coupling – TO – Flange Type 01


Totally fasteners Minimum Dim Minimum Stud Bolt

ID Dim Bolt
per joint, Hex ISO 4017 Stud Bolt ASME B18.2.1 length
mm ISO 4017
ISO/ASME bolt length, mm ASME B18.2.1 mm
51 4 M16 100 5/8" 100
76 4 M16 100 5/8" 100
102 6 M16 100 5/8" 100
127 6 M16 100 3/4" 100
152 6 M20 100 3/4" 120
204 6 M20 120 3/4" 120
254 10 M20 120 7/8" 120
305 10 M20 120 7/8" 120
355 12/8 M20 120 1" 120
405 12 M24 120 1" 140
457 16/12 M24 120 1" 140
508 16 M24 120 1" 140
610 16 M27 140 1 1/8'' 160
4868-03-23-EN-MNG
SLURRY HOSE SYSTEMS [Date]
Connection type: Trellex coupling – TO – Flange type 02/32

(E.G. Trellex hose – TO – Trellex steel rubber lines pipe)



ID Dim Bolt
mm ISO 4017
51 4 M16 120 5/8" 140
76 4 M16 120 5/8" 140
102 6 M16 140 5/8" 140
127 6 M16 140 3/4" 140
152 6 M20 140 3/4" 160
204 6 M20 140 3/4" 160
254 10 M20 140 7/8" 160
305 10 M20 160 7/8" 180
355 12/8 M20 160 1" 180
405 12 M24 160 1" 180
457 16/12 M24 180 1" 200
508 16 M24 120 1" 140
610 16 M27 140 1 1/8'' 160
4868-03-23-EN-MNG
SLURRY HOSE SYSTEMS [Date]
Connection type: Flange type 01 – TO – Flange type 02/32

(E.G. Trellex steel rubber lined pipe – Trellex steel rubber lines pipe)



ID Dim Bolt
mm ISO 4017
102 8 M16 140 5/8" 120
127 8 M16 140 3/4" 120
152 8 M20 140 3/4" 140
204 8 M20 140 3/4" 140
254 12 M20 140 7/8" 160
305 12 M20 160 7/8" 160
355 16/12 M20 160 1" 160
405 16 M24 180 1" 180
457 20/16 M24 180 1 1/8'' 200
508 20 M24 120 1 1/8'' 200
610 20 M27 120 1 1/4'' 200
4868-03-23-EN-MNG
Metso Outotec is a frontrunner in sustainable technologies, end-to-end solutions
and services for the aggregates, minerals processing and metals refining industries
globally. By improving our customers’ energy and water efficiency, increasing
their productivity, and reducing environmental risks with our product and
process expertise, we are the partner for positive change.
Metso Outotec, Töölönlahdenkatu 2, FI-00100, Helsinki, Finland

tel. +358 20 484 100
mogroup.com

Mo Slurry Hose Systems - Brochure en 4868 03 23 en MNG

Uploaded by

Copyright:

Available Formats

Mo Slurry Hose Systems - Brochure en 4868 03 23 en MNG

Uploaded by

Document Information

Original Description:

Original Title

Copyright

Available Formats

Share this document

Share or Embed Document

Sharing Options

Did you find this document useful?

Is this content inappropriate?

Copyright:

Available Formats

Mo Slurry Hose Systems - Brochure en 4868 03 23 en MNG

Uploaded by

Copyright:

Available Formats

Integrated solution with extensive application expertise

Slurry hose systems

Rubber Hoses…. ................................................................................................................. .........3

Coupling & Gaskets ..................................................................................................................... 3

Material Handling Slurry Hose T40.............................................................................................. 4

Material Handling Slurry/Bulk Hose T60 ..................................................................................... 5

3xD Bends 90° .............................................................................................................................. 6

3xD Bends 45°…… ....................................................................................................................... 7

Coated couplings ......................................................................................................................... 9

Rubber Lined Steel Pipe ............................................................................................................ 11

Branch Pipes S45....................................................................................................................... 12

Branch Pipes K45 ...................................................................................................................... 13

Branch Pipes T90 ....................................................................................................................... 14

Branch Pipes TX90..................................................................................................................... 15

Sliding Clamps… ....................................................................................................................... 17

Concentric Rubber Lined Steel Reducer .................................................................................. 18

Flange standard EN1092-1 ……………………………………………………………………………... 21

Flange standard ANSI 150 ……………………………………………………………………………… 22

Connection type: Trellex coupling – TO – Trellex coupling ……………………………………… 23

Connection type: Trellex coupling – TO – Flange type 01 …………………………………...…... 24

Connection type: Trellex coupling – TO – Flange type 02/32 ……………………………………. 25

Connection type: Flange type 01 – TO – Flange type 02/32 ……………………………………… 26

© 2023 Metso Outotec

Rubber Lined Steel Pipes

Coupling & Gaskets

Standards Specifications / Painting

According to PED EN 13480 Surface preparation blasting grade: Sa 2.5

According to EN3834. Primary Coat: EP (Zn (R)) 60/1

Flanges according to -EN1092-1 and ASME Top Coat: Pur 120/2

© 2023 Metso Outotec

Material Handling Slurry Hose T40

© 2023 Metso Outotec

Material Handling Slurry/Bulk Hose T60

© 2023 Metso Outotec

3xD Bends 90°

Part No. ID OD Wear tube Operating pressure AxB C R Weight

© 2023 Metso Outotec

3xD Bends 45°

Part No. ID OD Wear tube Operating pressure AxB C R Weight

© 2023 Metso Outotec

Areas of use: Pumping of extremely abrasive materials.

© 2023 Metso Outotec

© 2023 Metso Outotec

Areas of use: Pumping of extremely abrasive materials.

Part No. For internal hose diameter Weight

SH-373977 51 2” 0.06 0.15

SH-373902 127 5” 0.20 0.40

SH-373829 305 12” 0.70 1.50

SH-373795 457 18” 1.00 2.20

© 2023 Metso Outotec

Rubber Lined Steel Pipe

Areas of use: Pumping of extremely abrasive materials.

Characteristics: Rigid steel pipes with smooth rubber

Technical description: Steel pipes lined with natural

ID Length Wear Tube Flange drilling Operating Pressure Weight

ASME B16.5 150lbs Flange

© 2023 Metso Outotec

Branch Pipes S45