Professional Documents
Culture Documents
Yadav AdBlue
Yadav AdBlue
AdBlue: An Overview
Yadav Indrajit N.
Dept. of Chemical Engineering, Bharati Vidyapeeth Deemed University, Pune, (MS) India
indrajit.yadav@bharatividyapeeth.edu
ABSTRACT
AdBlue is an ultra pure solution of urea in demineralised water, used in the latest generation
of commercial diesel vehicles for the removal of Nitrous Oxide, an environmental pollutant.
It consists of high purity urea dissolved and suspended within deionized water. The ratio of
the mix is approximately 32.5% urea and 67.5% deionized water. It is used by modern diesel
engines which are equipped with an SCR, AdBlue never comes into contact with the fuel, and
it is a common misconception that it is an additive. AdBlue is carried onboard the vehicle in a
separate vessel to the fuel storage tank. It is injected into the exhaust gases as a post
combustion process through an SCR where it breaks harmful Nitrous Oxide emissions down
into mostly Nitrogen and Oxygen. The use of AdBlue benefits everyone it helps the
environment by reducing the number of harmful emissions created by diesel engines and it
helps fleet operators and drivers reduce fuel costs. It is likely that further savings will be
made in the future as governments are anticipated to introduce new carbon taxes and
penalties for individuals who do not take necessary action to reduce damage impacted on the
environment.
1. Introduction
AdBlue is the international name given to a newly created additive for selective catalytic
reduction. The name was created by joint agreement by the mineral oil industry, the chemical
industry and the automobile industry and their suppliers. AdBlue is such an additive. They
are stored as a concentration in a separate tank prior to mixing with the exhaust gases as they
leave the engine. In order to maintain efficiency and to be sure that systems are not
compromised, it is essential that the concentration is accurately maintained. Measuring
devices such as refractometers and hydrometers may perform such checks and depending on
the location and accuracy required. In an effort to reduce environmental pollution, has certain
rules established about emissions from heavy and light goods vehicles. One method adopted
by vehicle manufacturers to allow compliance is SCR (Selective Catalytic Reduction), which
chemically reduces NOx emissions using a urea additive in the exhaust flow.
With the industry focus placed on selective catalytic reduction (SCR) systems that require
urea dosing to reduce NOx, how urea is delivered and dosed has many system and engine
manufacturers considering sealing, pumping and environmental resilience of dosing systems.
Urea dosing systems require both a high dispense accuracy as well as low pressure. While a
dosing system solution is predicated on these exacting parameters, the technology to address
those needs is currently scarce. With everincreasing emissions regulatory restrictions,
precise and accurate dispensing in both infrastructure distribution as well as onvehicle
dosing remains a focus of concern, following attempts to address and allay some of these
concerns.
The guideline for this tightening of exhaust gas limits is the guideline for air quality which
aims further reduction of air pollution by industrial plants and motor vehicles. Therefore new
limits of euro 4 and euro 5 for exhaust gas emissions shall reduce the emission of pollutants.
A requirement for reduction in NOx emissions by diesel engines is influenced by Euro 4 and
Euro 5 legislation. Initial targets for emission reduction are Public Transport and the
Commercial Sector. According to new standards, NOx emissions have to be reduced in two
steps in 2005 (Euro 4) and 2008 (Euro 5), respectively, each time by 30 % visàvis the
current limits of Euro 3. Significantly tighter limits apply to the other pollutants, as well: for
carbon monoxide (CO), unburned hydrocarbons (HC) and most importantly for particulate
matter (PM) which is shown in table 1
2.1 AdBlue
Content Limit
Density at 20°C 1.0870 1.0920 g/cm³
Refractive index at 20°C 1.3817 1.3840
Melting enthalpy +270 J/g
Melting range (2 K/min) (20°C) to (6°C)
Specific heat capacity Cp(T) at 25.04°C 3.51 J/g*K
Vapor pressure above liquid at 20.08°C 23.0 hPa
Thermal conductivity at 25°C approx. 0.570 W/m∙K
Viscosity at 25°C approx. 1.4 mPa∙s
Surface tension at 20 °C min. 65 mN/m
pH slightly alkaline, approx. 9.0
To further reduce pollution and Greenhouse gases, countries around the world are introducing
ever more stringent exhaust emission regulations have developed different methods of
exhaust treatment, these are:
1. Internal measures to the engine: shape of the cylinder, mixing of the fuel/ignition,
valve timing
2. Catalytic converter for the reduction of CO, HC and NOx emissions while operating
the gasoline engine in a stoichiometric proportion of λ = 1
3. Converter plus operation of the engine with excess air (λ> 1) for reduction of NOx
emissions
4. Oxidation catalyst for decreasing CO, HC and also particulate matter emissions to a
certain extent
5. Exhaust gas recycling (EGR) for the reduction of NOx emissions
6. Storage catalyst with separate control for reduction of NOx emissions
7. Selective catalytic reduction (SCR) to decrease NOx emissions (with an additive as
a reducing agent)
8. Particle filter with continuous or discontinuous regeneration (with or without
additive as a regeneration aid)
The above methods can also be used in various combinations. However, there is a dilemma
when trying to reduce particle and NOx emissions simultaneously, because there is a
correlation between the formation of NOx on one hand and of the remaining pollutants on the
other: It is possible to reduce NOx emissions by internal measures, such as EGR, which
lowers the temperature in the cylinder of the engine.
However, emissions of particles, unburnt hydrocarbons and carbon monoxide would then
increase. In addition, efficiency and effectiveness of the diesel engine would be impaired and
therefore fuel consumption and carbon dioxide emissions will increase. If, however, the
combustion in the engine is optimized with regard to efficiency and performance, then
formation of particulate matter and NOx will increase to such an extent that the imminent
Euro standards cannot be met. Whereas the limit values of Euro 4 can still be met with
various methods, such as exhaust gas recirculation in combination with a particle filter, the
simultaneous reduction of NOx and particle emissions to the values of Euro 5 poses a
technical problem, which, according to current knowledge, can only be solved with one
specific method described such as selective catalytic reduction as follows.
An SCR system injects a product known as AdBlue into the hot exhaust gas where it
decomposes into ammonia, which then reacts with the surface of catalyst to produce nitrogen
and water vapor.
Ammonia (NH3) is used as a reducing agent; however, due to its aggressiveness and
toxicity, it is not applied as such, but in the form of an innocuous substance, which
releases NH3 in the exhaust gas stream, the engine can be operated under optimal
conditions, thus minimizing fuel consumption and therefore CO emissions as well as
the discharge of all pollutants except NOx. After the combustion gases have left the
engine, they first run through a preoxidation catalyst where hydrocarbons, carbon
monoxide and particulate matter unburned are oxidized as completely as possible. NO
is oxidized partly to NO, because the subsequent reduction proceeds fastest at a
mixing ratio of NO: NO2 of 1:1. Then a pump, which is controlled by a monitoring
unit, injects AdBlue from a separate tank into the hot exhaust gas stream, where it
hydrolyses to NH3 and CO2. In the actual selective reduction, NH3 reacts with the
NO/NO2 mixture to form nitrogen and water (steam), which with 80 % constitutes the
main natural component of the atmosphere. (Figure 1)
Figure 1: Scheme of a combined deNOx system for exhaust gas treatment on the basis of the
SCR method
The chemical reaction in the exhaust gas stream behind the engine at the ceramic catalyst
causes a reduction of the nitrogen oxides NO and NO by ammonia (NH3), according to the
following reactions
1. Partial oxidation:
2 NO + O2 → 2 NO2
2 CO + O2 → 2 CO2
4 HC + 3O2 → 2 CO2+ 2H2O
2. Urea hydrolysis
(NH2)2CO + H2O → 2 NH2 + CO2
4. Oxidation catalyst
3 O2 + 4 NH3 → 2 N2 + 6 H2O
3. Discussion
Consumption of AdBlue will be from 4 to 6% of the diesel consumption has been issued. To
meet these standards the automotive industry has adopted several technologies; one such is
Selective Catalytic Reduction (SCR), where harmful exhaust gases are converted to nitrogen
and water by catalytic conversion. AdBlue is the trade name for a catalytic reduction agent
used for this process. It stored at refueling sites and will become a common feature at filling
stations for commercial diesel vehicles and private depots. Vehicles will have an AdBlue tank,
from which it is injected into the engine exhaust stream immediately after the combustion
chamber.
AdBlue is stored in containers that are specifically designed and manufactured from materials
that are suitable for use with urea. The same applies to all storage ancillary equipment, such
as valves, dispensing nozzles and pipe work. AdBlue is soluble in water and should be kept
out of surface water drainage systems discharging to the environment. It will not be removed
in an oil separator so it’s important to isolate dispensing area drainage from the surface water
system to reduce the possibility of spills and drips causing pollution. AdBlue poses no serious
risk to humans, animals or the environment. However, it should be stored separately from
nitrates and nitrites. Thus these are following factors discussed in brief:
Stability tests
1. Storage stability
2. Thermal stability
Field tests
1. Concrete
2. Metals and plastic material
3. Seals
Emulsion test
A number of committees of the automobile and mineral oil industry as well as their
associations, scientific societies, accessories industry, urea manufacturers, shipping agencies,
environmental authorities and universities are engaged on a national or international level in
the issue of reducing NOx emissions from diesel engines and more specifically in the
SCR/urea technology. The activities of the main committees are described
4. Conclusion
1. Due to its excellent solubility in water (1,080 g/l) urea will tend to stay in the aqueous
phase in an oil separator, and from there it will get into the public sewage system and
eventually into the public waste water treatment plants. There it will be completely
catabolized within a few days. However, the question of permits for release of urea
solutions into the public sewage systems still needs to be investigated.
2. As SCR is a chemical process, the exhaust gas can smell different to a conventional
diesel vehicle. In addition, some “white smoke” might be seen from the exhaust pipe
when the engine is started, this is only water vapor. Do not touch this vapor as it may
be slightly acidic. If it makes contact with skin, or clothes, flush the area well with
water.
1. Cleaner Emissions
2. The engine can be operated at optimal conditions
3. The optimal engine adjustment results in a better efficiency (about 5 % less fuel
consumption) and therefore in less CO2 emissions.
4. The discharge of all pollutants (NOx, PM, CO and CH) is minimized, thereby
complying with the stringent requirements of Euro 4 and 5.
5. The SCR/urea technology is applicable to all types of engines and functions with
diesel fuels of varying qualities.
6. The SCR method is maintenancefree and designed for the entire lifespan of the
vehicle.
7. SCR has no influence on service and oil change intervals of the vehicles.
5. References
2. DGMK Research Report 6162 (2005), “, AdBlue as a Reducing Agent for the
Decrease of NOx Emissions from Diesel Engines of Commercial Vehicles”,
Hamburg, pp 127
3. Technical Leaflet BASF the chemical Company (2005), “AdBlue, ECAL/L, Rev.
1, pp 16
4. AdBlue Material Data Safety Sheet, Liquid Management Solutions Ltd, Creative
Industries Centre, Wolverhampton Science Park, Glaisher Drive, Wolverhampton
WV10 9TG, pp 14
6. Safety Data Sheet, Air1, Conforms to Regulation (EC) No. 1907/2006 (REACH),
Annex II United Kingdom (UK)
7. José María López, Felipe Jiménez, Francisco Aparicio and Nuria Flores (2009),
“Onroad emissions from urban buses with SCR + Urea and EGR + DPF systems
using diesel and biodiesel”, Transportation Research Part D: Transport and
Environment, 14(1), pp 15
10. Lei Jiang, Yunshan Ge, Asad Naeem Shah, Chao He and Zhihua Liu (2010),
“Unregulated emissions from a diesel engine equipped with vanadiumbased urea
SCR catalyst”, Journal of Environmental Sciences, 22(4), pp 575581