DP8600C LINEAR INTEGRATED CIRCUIT

VOLTAGE MODE PWM CONTROL

CIRCUITS

DESCRIPTION
The DP8600C incorporate on a single monolithic chip all
the functions required in the construction of a pulse-width
modulation control circuit.Designed primarily for power DIP-16
supply control, the device offers the systems engineer the
flexibility to tailor the power supply control circuitry to its
application.
The DP8600C contains an error amplifier,current-limiting
amplifier, an on-chip adjustable oscillator, a dead time
control comparator,pulse-steering control flip-flop,a 5-
volt ,1% precision supply regulator,and output control
circuits. SOP-16
The error amplifier exhibits a common-mode Voltage
range from -0.3V to VCC-2V.The current-limit amplifier
exhibits a common-mode Voltage range from -0.3V to 3V
with an offset Voltage of approximately 80 mV in series FEATURES
with the inverting input to ease circuit design requirements. * Complete PWM Power Control Circuitry
The dead-time control comparator has a fixed offset that * Uncommitted Outputs for 200 mA Sink or
provides approximately 5% dead time when externally Source Current
altered. The on-chip oscillator may be bypassed by * Output Control Selects single-Ended or
terminating RT(pin 6) to the reference output and providing Push-
a sawtooth Input to CT(pin 5),or it may be used to drive the Pull Operation
common circuits in synchronous multiple-rail power * Internal Circuitry Prohibits Double control
supplies. Over
The Uncommitted output transistors provide either Total Range
common-emitter or emitter-follower output capability.Each * Circuit architecture Allows easy Synchron -
device provides for push-pull or single-ended output Ization
operation,which may be selected through the output-control * Undervoltage Lockout
function. the architecture of these devices prohibits the
possibility of either being pulsed twice during push-pull
operation.

ABSOLUTE MAXIMUM RATINGS

(Unless otherwise noted ,all is over operating free-air temperature Range)
Characteristic Symbol Value Unit
Supply Voltage(note 1) Vcc 40 V
Amplifier Input Voltage Vi Vcc+0.3 V
Collector Output Voltage Vo 41 V
Collector Output Current Ico 250 mA
Continuous total dissipation at(or for below) 25 free air PD 1000 mW
temperature(note 2)
Operating Temperature Range Topr -20 to 85 °C
Storage Temperature Range Tstg -65 to 150 °C
lead Temperature 1.6mm from case for 60 sec. Tcase 300 °C

note1: All voltage values,except differential voltages are with respect to the network ground terminal.
note 2:For operation above 25°C free-air temperature,The dissipation derates with 9.2mW/°C.

YOUWANG ELECTRONICS CO.LTD 2011.09.09 V1.1

1
DP8600C LINEAR INTEGRATED CIRCUIT
BLOCK DIAGRAM

RECOMMENDED OPERATING CONDITIONS

Values
Characteristic Symbol Unit
min max
Supply Voltage Vcc 7 36 V
Amplifier Input Voltage Vi -0.3 Vcc-2 V
Collector Output Voltage Vo 40 V
Collector Output Current(each Transistor) Ic 200 mA
Current into feedback If 0.3 mA
Timing capacitor CT 0.47 10000 nF
Timing Resistor RT 1.8 500 kΩ
Oscillator frequency fosc 1 300 kHz
Operating free-air temperature Ta 0 70 °C

YOUWANG ELECTRONICS CO.LTD 2011.09.09 V1.1

2
DP8600C LINEAR INTEGRATED CIRCUIT
ELECTRICAL CHARACTERISTICS
(Over recommended operating free-air temperature range,VCC=15V,f=1kHz,Unless otherwise specified)
Characteristic Test Conditions Min Typ Max Unit
Reference Section
Output voltage Io=1mA 4.9 5 5.1 V
Input regulation Vcc=7V to 36V 2 25 mV
Output Regulation Io=1 to 10mA 1 15 mV
Output Voltage change with
∆TA=MIN to MAX(note 2) 0.2 1 %
Temperature
Short-circuit output Current Vref=0 35 mA
Characteristic Test Conditions Min Typ Max Unit
Oscillator section
Frequency CT=0.01µF,RT=120kΩ 10 kHz
All Values of Vcc CT,RT,TA
Standard Deviation of Frequency 10 %
constant
Frequency Change with Voltage Vcc=7V to 36V,Ta=25°C 0.1 %
CT=0.01µF,RT=12kΩ,∆TA=
Frequency Change with temperature 12 %
MIN to MAX
Amplifier Section
Input offset Voltage Error Vo(pin 3)=2.5V 2 10 mV
Input offset Current Vo(pin 3)=2.5V 25 250 nA
Input bias Current Vo(pin 3)=2.5V 0.2 1 µA
-0.3
Common-mode Input Voltage Range Error Vcc=7V to 36 V to V
Vcc-2
Open-Loop Voltage Amplification ∆Vo=3V, Vo=0.5V to 3.5V 70 95 dB
Unity-Gain Bandwidth 800 kHz
Common-Mode Rejection ratio Error Vcc=36V,TA=25°C 65 80 dB
VID=-15mV to -5V
output sink current(pin 3) 0.3 0.7 mA
V(pin 3)=0.5V
VID=15mV to -5V V(pin
Output source Current(pin 3) -2 mA
3)=3.5V
Output Section
Collector off-state current VCE=40V,Vcc=36V 2 100 µA
Emitter off-state Current VCC=VC=36V,VE=0 -100 µA
Common
Collector -emitter Saturation Voltage VE=0,Ic=200mA 1.1 1.3 V
-emitter
Emitter-
Vc=15V,IE=-200mA 1.5 2.5
Follower
Output Control input Current Vi=Vref 3.5 mA

YOUWANG ELECTRONICS CO.LTD 2011.09.09 V1.1

3
DP8600C LINEAR INTEGRATED CIRCUIT

Dead Time Control Section

Input bias (pin 4) Vi=0 to 5.25V -2 -10 µA
Maximum duty cycle,each output VI(pin 40=0 45 %
Input threshold Voltage(pin 4) Zero duty Cycle 3 3.3 V
Maximum duty cycle 0
PWM comparator Section
Input Threshold Voltage(pin 3) Zero Duty cycle 4 4.5 V
Input sink current (pin 3) Vpin 3= 0.7V 0.3 0.7 mA
Total Device
pin 6 at Vref,all other Inputs
Standby supply current Vcc=15V 6 10 mA
and outputs open
Vcc=40V 9 15
Average supply current Vpin 4=2V 7.5 mA
Switching Characteristics,Ta=25°C
Common-emitter
Output Voltage rise time 100 200 ns
configuration
Output Voltage fall time 25 100 ns
Emitter-follower
Output Voltage rise time 100 200 ns
configuration
Output Voltage fall time 40 100 ns

note 1:All typical Values except for temperature coefficient are at Ta=25°C.
note 2:For conditions shown as MIN or MAX, use appropriate value under recommended operating
conditions.
note 3:Duration of the short-circuit should not exceed one second.
note 4:Standard deviation is a measure of the statistical distribution the mean as derived from the formula :
N
2
(xn-x)
= n=1
N-1

YOUWANG ELECTRONICS CO.LTD 2011.09.09 V1.1

4
DP8600C LINEAR INTEGRATED CIRCUIT

PIN CONFIGURATIONS

NONINV NONINV
1 16
INPUT INPUT

INV INPUT 2 15 INV INPUT

FEEDBACK 3 14 Vref

DEAD-TIME OUTPUT
4 13
CONTROL CONTROL

CT 5 12 Vcc

RT 6 11 C2

GND 7 10 E2

C1 8 9 E1

TYPICAL APPLICATION CIRCUIT

YOUWANG ELECTRONICS CO.LTD 2011.09.09 V1.1

5
DP8600C LINEAR INTEGRATED CIRCUIT
TEST CIRCUIT

Vcc=15V

2W 2W
12 150 150
TEST
INPUTS 4 Vcc 8
DEAD-TIME C1
3 9 OUTPUT 1
FEEDBACK E1
12k
6
RT
5 11
CT C2
0.01 F 1
OUTPUT 2
E2 10
2
ERROR
16 AMPLIFIER
15
Vref
13 OUTPUT OUTPUT 14
CONTROL
50k
7

VOLTAGE
at C1

VOLTAGE
at C2

VOLTAGE
at CT

DEAD-TIME THRESHOLD VOLTAGE

CONTROL INPUT

THRESHOLD VOLTAGE
FEEDBACK

FIG 1. OPERATIONAL TEST CIRCUIT AND WAVEFORMS

ERROR
AMPLIFIER
1

Vin
FEEDBACK
2 TERMINAL

16

Vref
15
ERROR
AMPLIFIER
FIG 2. AMPLIFIER CHARACTERISTICS

YOUWANG ELECTRONICS CO.LTD 2011.09.09 V1.1

6
DP8600C LINEAR INTEGRATED CIRCUIT

FIG. 3 COMMON-EMITTER CONFIGURATION

Vcc
EACH
OUTPUT 90% 90%
CIRCUIT Q
Ve

10% 10%
68¦¸ 15pF tr tf

FIG. 4 EMITTER -FOLLOWER CONFIGURATION

YOUWANG ELECTRONICS CO.LTD 2011.09.09 V1.1

7
DP8600C LINEAR INTEGRATED CIRCUIT
TYPICAL PERFORMANCE CHARACTERISTICS

FIG 5.

100

Vcc=15V
¡÷V=3V
80 Ta=25¡æ

60

40

20

0
2 3 4 5 6
10 10 10 10 10
Frequency (Hz)

Fig.6

YOUWANG ELECTRONICS CO.LTD 2011.09.09 V1.1

8
DP8600C LINEAR INTEGRATED CIRCUIT
PACKAGE DIMENSIONS
DIP-16-300-2.54 Unit: mm

SOP-16-225-1.27 Unit: mm

YOUWANG ELECTRONICS CO.LTD 2011.09.09 V1.1

9