Queensland Urban Drainage Manual volume 1 second edition 2007

4.00 Catchment hydrology 4.01 Hydrologic methods

The choice of hydrologic method must be appropriate to the type of catchment and the required degree of accuracy. Simplified hydrologic methods such as the Rational Method should not be used whenever a full design hydrograph is required for flood mapping or to assess flood storage issues. Instead the more reliable runoff-routing techniques presented in publications such as Australian Rainfall & Runoff (ARR) should be adopted. Unless otherwise directed, a method that generates a hydrograph must be adopted for the design of those components of the drainage system which are volume dependent, such as detention basins. A detailed description of these methods is not included in this Manual. The Rational Method provides a simplistic methodology for assessing the design peak flow rate to enable the determination of the sizes of drainage systems within urban catchment area less than 500 hectares (5km2) or rural catchment less than 25 km2. Unfortunately the Rational Method has significant limitations, and it is the task of the designer to be familiar with these limitations and to know when an alternative methodology is required. A brief description of some commonly used hydrologic methods is given below: (a) The rational method

The Rational Method provides a simple means for the assessment of the peak discharge rate for design storms, but does not provide a reliable basis for the determination of runoff volume, hydrograph shape, or peak discharge rates from historical (real) storms. Use of the Rational Method is generally not suitable for the following applications: (i) analysis of historical storms; (ii) design of detention basins; (iii) catchments of unusual shaperefer to Section 4.03.2; (iv) catchments with significant, insolated areas of vastly different hydrologic characteristics, such as a catchment with an upper forested sub-catchment and a lower urbanised sub-catchment; (v) catchments with significant floodplain storage, detention basins, or catchments with wide spread use of on-site detention systems; (vi) urban catchments with an area greater than 500 hectares; (vii) catchments with a time of concentration greater than 30 minutes where a high degree of reliability is required.
4-1

Queensland Urban Drainage Manual volume 1 second edition 2007

(b)

Synthetic unit hydrograph procedure

The Clarke-Johnstone Synthetic Unit Hydrograph procedure is described in Australian Rainfall and Runoff (ARR-1998) and involves the construction of a time-area diagram for the catchment, the routing of this through a linear storage and the convolution of the resulting unit hydrograph with the hyetograph to obtain a hydrograph at the point under consideration. (c) RORB, RAFTS, WBNM & URBS

RORB, RAFTS, WBNM and URBS are computer based runoff routing models for calculating flood hydrographs from rainfall, catchment and channel inputs. RORB is more frequently used for rural and sparsely developed catchments. RAFTS, WBNM and URBS have been widely used for both rural and urban catchments. These models use the concept of critical storm duration as opposed to the concept of time of concentration used in the Rational Method. The critical storm duration for a given catchment may be similar in duration to the time of concentration, but the two terms are different and should not be confused. The critical storm duration is determined by testing the model for a range of storm durations. Calibration of these models with actual flow data is recommended, particularly for urban areas. Where this is not possible, guidance on suitable model parameters for rural catchment is given by Weeks (1986) and McMahon and Muller (1986). These model parameters should be used in urban catchments with caution. Suggested procedures for accounting for the degree of urbanisation are given in Section 4.09. Alternatively, model results may be compared with the output from other runoff-routing models. For small catchments less than 500ha, it is common to compare the results to a Rational Method peak discharge. This comparison should be to the satisfaction of the relevant regulating authority. A statement should be prepared providing justification for any differences between the models used. Runoff-routing models such as RORB, RAFTS, WBNM and URBS can produce erroneous results when flows are extracted from the models at Node locations that have just a few contributing sub-areas. This is because there may be insufficient sub-catchments to achieve a suitable balance between the calibrated rainfall runoff and flood routing components of the model. It should be noted, however, that this problem does not always occur. Ideally these models should have at least 5 sub-catchments upstream of the point of interest. Alternatively, refer to the User Guide for the computer program for guidance. RAFTS features an automatic subdivision of each nominated sub-catchment into ten sub-areas which is thought to significantly reduce the risk of
4-2

Queensland Urban Drainage Manual volume 1 second edition 2007

erroneous results when stream flows are extracted from the model at Nodes that have just a few contributing sub-catchments. (d) Time-area runoff routing, e.g. drains & pc-drain

DRAINS and PC-DRAIN are computer-based models which incorporate the routing of the time-area relationship developed for the sub-catchments under consideration. DRAINS was developed from the TRRL Method, ILLUDAS and later, ILSAX. It is suitable for use in urban catchments, but requires calibration with available flow data. Where this is not available it is recommended that the obtained hydrograph be compared with the peak discharge derived for the same catchment using the Rational Methodnoting the issues raised in (c) above.

4.02 Hydrologic assessment

(a) Hydrologic assessment of catchments not fully developed

Traditional drainage standards require design discharge rates to be based on a fully developed catchment in accordance with the current Planning Scheme or Strategic Plan. Unless otherwise directed by the local government, the design discharge rate has traditionally assumed no flow attenuation within future upstream developments. The main benefit of this practice was that it minimised the need for stormwater detention/retention systems within developing catchments. The disadvantages associated with this approach are: (i) accelerated downstream watercourse erosion if runoff from the upstream development is not regulated to avoid increases in discharge; (ii) high cost of trunk drainage systems. Even with current stormwater practices it may not always be appropriate to assume future upstream developments will adequately attenuate flows. For example, parts of the upper catchment may have been approved for development under an old Planning Scheme where flow attenuation was not required. Developers need to obtain guidance from the local government as to what flow conditions should be assumed for the fully developed upstream catchment. (b) Example of catchments where application of the rational method is generally not recommended

The following section provides guidelines on the hydrologic assessment of catchments which contain features that are likely to significantly limit the applicability of the Rational Method. These catchment conditions are

4-3

Queensland Urban Drainage Manual volume 1 second edition 2007

assumed to exist upstream of the location where a design discharge is required. Catchment 1: Overland flow path passing through a low gradient oval or park that provides significant detention storage in major storm events Use of the Rational Method to calculate peak flows downstream of the oval/park is not recommended. Note; it is inappropriate to use the very low flow velocities passing through the flooded oval to determine a time of concentration downstream of the oval. Peak flow should be determined using a routing model that adequately accounts for flood storage, i.e. the oval/park may need to be modelled as a detention system.

Catchment 2: Catchments where travel time for the minor drainage system is significantly different from that of the major drainage (overland flow) system If the Rational Method is used then the time of concentration should be based on the shortest travel time, otherwise use a runoff-routing model. If the assessment of peak discharge is a critical design issue, then an appropriate runoff-routing model should be used.

Catchment 3: Relief drainage works incorporating split pipe flows The assumed flow rate in each pipe should not be based on pipe gradient, but on an appropriate hydraulic gradeline analysis. Alternatively, use an appropriate pipe network or time-area runoff routing model to analyse the drainage system (preferred).

4-4

Queensland Urban Drainage Manual volume 1 second edition 2007

Catchment 4: The upstream Future Urban catchment area is currently undeveloped Design flow rates should be based on ultimate development of the catchment based on the current Planing Scheme or Strategic Plan, whichever results in higher flows. It should be assumed that future upstream development will alter existing flow conditions, unless agreed in principle by the local government. Refer to discussion in Section 4.02 (a).

Catchment 5: Catchments containing significant on-site stormwater detention (OSD) Use of the Rational Method to calculate minor storm flow rates is likely to be inappropriate. The Rational Method may be used if applied in a conservative manner (i.e. OSD systems are ignored). Typically the OSD systems should be ignored when analysing major storm events. For those areas with on-site detention, the local government may agree to the adoption of a runoff coefficient (C) based on an appropriate pre-development land use. Alternatively, use a runoff-routing model with allowance made for the OSD systems.

Catchment 6: Sub-catchments containing one or more large lakes, wetlands, or detention/retention basins

Hydrological analysis should be performed using an appropriate runoff-routing model. Use of the Rational Method to calculate peak flow rates downstream of the water storage is not recommended.

4-5

Queensland Urban Drainage Manual volume 1 second edition 2007

Catchment 7: Catchments containing a major water supply dam or weir Use of the recommended. Rational Method is not

General practice is to assume the dam/weir is full at the start of the design storm.

Catchment 8: Catchments with an upper containing an existing farm dam

rural

area

It should be assumed that the farm dam may one day be removed (even if the area stays rural) therefore, design flows downstream of the dam should consider both the dam and no dam condition. General practice is to assume the dam is full at the start of the design storm.

Catchment 9: Urban catchments with an area greater than 500ha. Use of the recommended. Rational Method is not

Catchments should be analysed using an appropriate runoff-routing model. Runoff-routing models of ungauged urban catchments can be compared to the Rational Method, but only at locations where the upstream catchment areas is less than 500 hectares.

4-6

Queensland Urban Drainage Manual volume 1 second edition 2007

Catchment 10: Catchments developed using the principles of Water Sensitive Urban Design Applicability of the Rational Method will depend on the degree of on-site detention (refer to Catchment 5). The Rational Method may be appropriate for the determination of peak discharge rates for major design storms for catchment less than 500ha. Alternatively, use an appropriate runoffrouting model.

The above discussion does not apply to water quality modelling of WSUD systems.

Catchment 11: Partially urbanised, ungauged catchments Use of the Rational Method may produce highly erroneous results. Catchments should be analysed using an appropriate runoff-routing model. Results from runoff-routing models of ungauged catchments may be compared with results from a Rational Method analysis for catchments less than 500 hectare using the following procedure: (i) compare the results assuming a fully undeveloped catchment (i.e. assuming the lower catchment is undeveloped); compare the results assuming a fully developed catchment (i.e. assuming the upper catchment is developed); adjust the parameters used in the runoffrouting model based on past experience of similar catchments and the results of steps (i) & (ii). Note, output from the runoffrouting model should not be calibrated to match the Rational Method unless there is reasonable and logical justification.

(ii)

(iii)

4-7

Queensland Urban Drainage Manual volume 1 second edition 2007

Catchment 12: Irregular shaped catchments Non-critical design discharge rates may be determined using the Rational Method with appropriate adjustments made to the time of concentration (refer to Section 4.03.2). In critical locations or where an accurate estimation of design discharge is required, use an appropriate runoff-routing model.

Catchment 13: Catchments with a significant change in catchment slope or stream slope Use of the Rational Method can produce highly erroneous results. In some cases, an estimate of design discharge rates may be determined using the procedures presented in Section 4.03.2. Catchments should be analysed using an appropriate runoff-routing model.

4-8

Queensland Urban Drainage Manual volume 1 second edition 2007

4.03 The rational method 4.03.1 General

In its general form the Rational Formula is: Q = C.I.A (4.01)

For design, the formula becomes: Qy = where Qy = Cy = A

t

(2.78 x 10 -3) Cy . tIy . A peak flow rate (m3/s) for average recurrence interval (ARI) of y years coefficient of discharge (dimensionless) for ARI of y years area of catchment (ha)

(4.02)

Iy = =

average rainfall intensity (mm/h) for a design duration of t hours and an ARI of y years. the nominal design storm duration as defined by the time of concentration (tc) refer to Section 4.06

The value of 2.78 x 10 -3 (or 1/360) is a conversion factor to suit the units used. Calculation of the flow at the various inlets and junctions along the drainage line is carried out from the top of the system progressively downstream. The total peak flow at any point is not the sum of the calculated sub-area flows contributing at that point, but is dependent on the time of concentration at that point. The actual flow being the product of the sum of the C.A values of the contributing sub-catchments, multiplied by tIy appropriate for time of concentration at that point. Q peak = (2.78 x 10 -3).[(C.A)]. tIy (m3/s) (4.03)

The time of concentration (tc) is defined as the travel time for flow from the most remote part of the catchment to the outlet, or the time taken from the start of rainfall until all of the catchment is simultaneously contributing flow to the outlet. The Rational Method should not be used to analyse historical (real) storms. For additional explanation of the Rational Method refer to Books 4 and 8 of Australian Rainfall and Runoff (1998).

4-9

Queensland Urban Drainage Manual volume 1 second edition 2007

4.03.2

The partial area effect

In general, the appropriate time of concentration (tc) for calculation of the flow at any point is the longest time of travel to that point. However, in some situations, the maximum flow may occur when only part of the upstream catchment is contributing. Thus the product of a lesser C.A and a higher tIy (resulting from a lower tc) may produce a greater peak discharge than that if the whole upstream catchment is considered. This is known as the "Partial Area Effect". Usually the above effect results from the existence of a sub-catchment of relatively small C.A but a considerably longer than average tc. This can result from differences within a catchment of surface slope, or from catchment shape. Typical cases include a playing field or open space within a residential area, or an elongated catchment. Figure 4.01 shows various examples.

Figure 4.01 Examples of catchments that may be subject to partial area effects

It is important to note that particular sub-catchments may not produce partial area effects when considered individually, but when combined at some downstream point with other sub-catchments, the peak discharge may result when only parts of these sub-catchments are contributing. The onus is on the designer to be aware of the possibility of the "Partial Area Effect" and to check as necessary to ensure that an appropriate peak discharge is obtained. There are two generally accepted Rational Method-based procedures for the calculation of peak flow rates from partial areas as presented below; however, it is generally recommended that the hydrologic assessment of catchments with unusual or widely varying surface features should be undertaken with an appropriate numerical runoff-routing model.
4-10

Queensland Urban Drainage Manual volume 1 second edition 2007

(a)

Simplified procedure

A simplified procedure is given in Section 4.5 of Argue (1986) based upon a comparison between the full area discharge and the partial area peak discharge for the time of concentration of the impervious areas of the critical sub-catchment. Care must be exercised as this procedure can underestimate the peak discharge. The method involves the use of a time of concentration ti corresponding to the flow travel time from the most remote, directly connected, impervious area of the catchment to the point under consideration. Thus, the calculated peak discharge is that from the impervious portion of the catchment plus that from the pervious part of the catchment which has begun to contribute up to time ti since the storm began. Thus,
t C. A = Ci . Ai + i . C p . Ap tc

(4.04)

Care must be used in applying this equation to catchments of irregular shape, and a case by case assessment is recommended. (b) Isochronal method

This is a trial and error method that is applicable where it is possible to identify those sub-catchments likely to have long response times relative to the balance of the catchment. Isochrones are lines drawn on a catchment plan passing through points which have equal travel times to the catchment outlet. Isochrones are drawn for the critical sub-catchments and these are used to assess the contributing area for a range of travel times from which the highest peak discharge is selected. Depending upon the complexity of the sub-catchments it may be necessary to distinguish between pervious and impervious areas both in respect of travel time to the outlet and their effect upon the equivalent impervious area under consideration.

4-11

Queensland Urban Drainage Manual volume 1 second edition 2007

4.04 Catchment area

The boundaries of catchment areas may be determined from contour maps, council records, aerial photographs and field inspection. When selecting the catchment area the following issues and guidelines should be considered: (i) Where the contributing catchment includes existing subdivided areas, the location of existing drainage works needs to be determined, either by field inspection, council records, or from "As Constructed" drainage plans. In urbanised catchments, ridgelines should not automatically be adopted as catchment boundaries because pipe drainage systems may collect and carry stormwater across the natural catchment boundary. The catchment area should take into account likely future road layouts and road drainage patterns if the contributing catchment includes areas subject to future development. In older urban areas where existing roads have a high crown, stormwater runoff may be re-directed by the crown of the road (Figure 4.02). When determining the catchment area, appropriate consideration should be given to the likelihood that the road will one day be resurfaced and re-profiled, causing stormwater to return to its natural flow path (Figure 4.03). In such cases, the design of new drainage works must adopt a conservative catchment area.

(ii)

(iii)

(iv)

Figure 4.02 Kerb flow diverted by road crown

Figure 4.03 Surface flow following re-profiling of the road crown

(v)

When assessing catchment boundaries, allowance should be made of the possible piping of runoff against the natural ground slope, e.g. the connection of roof water drainage to the street. This may be especially significant in Industrial and Commercial areas where factory roofs and surrounding car parks may drain in opposite directions. Roads, fences and pathways may significantly alter catchment boundaries. Property fencing and sound-control fencing can either block or significantly alter the direction of surface runoff. The effective catchment area of the minor drainage system may be different from the catchment area of the major drainage system. In

(vi)

(vii)

4-12

Queensland Urban Drainage Manual volume 1 second edition 2007

some cases the piped drainage system may discharge at a different location to that of the overland flow path. (viii) In small urban catchments, the effective catchment boundary may be governed by the location of allotment boundaries as shown in Figure 4.04.

Figure 4.04 Catchment boundaries showing the difference between the natural contour catchment and the actual urban drainage catchment

4-13

Queensland Urban Drainage Manual volume 1 second edition 2007

4.05 Coefficient of discharge

The coefficient of discharge C is a coefficient used within the Rational Method. The value of C is a statistical composite of infiltration and other losses, and to some degree, channel storage. It should not be confused with the volumetric runoff coefficient CV which is the ratio of total runoff to total rainfall. The coefficient of discharge must account for the future development of the catchment as depicted in the Planning Scheme or zoning maps for the relevant local government, but should not be less than the value determined for the catchment under existing conditions. It is recommended that the coefficient of discharge should be calculated using the method presented in Book 8 of ARR (1998), with the exception of 100% pervious surface. This method is summarised in the following steps: STEP 1 STEP 2 STEP 3 STEP 4 STEP 5 Determine the fraction impervious fi for the catchment under study from Table 4.05.1. Determine the 1 hour rainfall intensity 1I10 for the 10 year ARI at the locality. Refer to Section 4.07. Determine the Frequency Factor Fy for the required design storm from Table 4.05.2. Determine the 10 year C value from Tables 4.05.3 (a) & (b). Multiply the C10 value by the Frequency Factor Fy to determine the coefficient of runoff for the design storm Cy. Cy = Fy . C10 (4.05)

Note, in certain circumstances the resulting value of Cy will be greater than 1.0. In accordance with the recommendations of ARR (1998), a limiting value of Cy = 1.0 should be adopted for urban areas. There is little evidence to support an allowance for either slope or soil type in fully developed (non WSUD) urban areas. If there are significant local effects, and reliable data is available, then adjustments for soil type may be incorporated within the calculations at the discretion of the designer in consultation with the relevant local authority. The relationships shown in Book 8 of ARR (1998) and adopted in this Manual apply to areas that are essentially homogeneous, or where the pervious and impervious portions are so intermixed that an average is appropriate. In cases where separable portions of a catchment are significantly different, they should be divided into sub-catchments and different values of C applied.
4-14

Queensland Urban Drainage Manual volume 1 second edition 2007

Notwithstanding the above notes and limitations, it is the responsibility of the designer to ensure each sub-catchment flow is determined using a suitable coefficient of discharge. The local government may set specific C values to be used within their area.
Table 4.05.1 Fraction impervious vs. development category Fraction Development Category Impervious (i) Central Business Commercial, Local Business, Neighbouring Facilities, Service Industry, General Industry, Home Industry Significant Paved Areas e.g. roads and car parks Urban Residential High Density Urban Residential Low Density (including roads) Urban Residential Low Density (excluding roads) Rural Residential Open Space & Parks etc. 1.00 0.90 0.90 0.70 to 0.90 0.45 to 0.85 0.40 to 0.75 0.10 to 0.20 0.00

Notes: 1. Designer should determine the actual fraction impervious for each development. Local governments may specify default values. 2. Typically for Urban Residential High Density developments: townhouse type development fi = 0.7 multi-unit dwellings > 20 dwellings per hectare fi = 0.85 high-rise residential development fi = 0.9 3. In Urban Residential Low Density areas fi will vary depending upon road width, allotment size, house size and extent of paths, driveways etc. 4. See Table 7.02.2 for the definition of Development Categories. Table 4.05.2 Table of frequency factors

A.R.I. (years) 1 2 5 10 20 50 100

Frequency Factor (Fy) 0.80 0.85 0.95 1.00 1.05 1.15 1.20

Note: Where a coefficient of discharge calculated from Equation 4.5 for an urban catchment exceeds 1.00, it should be arbitrarily set to 1.0 in accordance with the recommendations of Australian Rainfall and Runoff (1998).

4-15

Queensland Urban Drainage Manual volume 1 second edition 2007

Table 4.05.3 (a) Intensity (mm/hr) 1 I10 39-44 45-49 50-54 55-59 60-64 65-69 70-90
1

Table of C10 Values FRACTION IMPERVIOUS i

0.00 Refer to Table 4.05.3(b)

0.20 0.44 0.49 0.55 0.60 0.65 0.71 0.74

0.40 0.55 0.60 0.64 0.68 0.72 0.76 0.78

0.60 0.67 0.70 0.72 0.75 0.78 0.80 0.82

0.80 0.78 0.80 0.81 0.83 0.84 0.85 0.86

0.90 0.84 0.85 0.86 0.86 0.87 0.88 0.88

1.00 0.90 0.90 0.90 0.90 0.90 0.90 0.90

I10 C10 fi

= = =

One hour rainfall intensity for a 1 in 10 year ARI Coefficient of discharge for a 1 in 10 year ARI Fraction impervious C10 values for Zero Fraction Impervious [1]
Medium density bush, or Good grass cover, or High density pasture, or Zero tillage cropping Light cover bushland, or Poor grass cover, or Low density pasture, or Low cover bare fallows

Table 4.05.3 (b)

Land Dense bushland description

Intensity (mm/hr) 1 I10 3944 4549 5054 5559 6064 6569 7090

Soil permeability High 0.08 0.10 0.12 0.13 0.15 0.17 0.18 Med 0.24 0.29 0.35 0.40 0.44 0.50 0.53 Low 0.32 0.39 0.46 0.53 0.59 0.66 0.70

Soil permeability High 0.16 0.20 0.23 0.27 0.30 0.33 0.35 Med 0.32 0.39 0.46 0.53 0.59 0.66 0.70 Low 0.40 0.49 0.58 0.66 0.70 0.70 0.70

Soil permeability High 0.24 0.29 0.35 0.40 0.44 0.50 0.53 Med 0.40 0.49 0.58 0.66 0.70 0.70 0.70 Low 0.48 0.59 0.69 0.70 0.70 0.70 0.70

Note: [1] Developed from Qld. Department of Natural Resources & Mines (2005). Coefficients are not suitable for soils compacted by construction activities.

4-16

Queensland Urban Drainage Manual volume 1 second edition 2007

4.06 Time of concentration (rational method) 4.06.1 General

The time of concentration (tc) of a catchment is defined as the time required from the start of a design storm for surface runoff to collect and flow from the most remote part of the catchment to its outlet. Its significance is in the assumption that for a given design storm frequency, peak flow at the catchment outlet will result from a storm of duration equal to the time of concentration. In reality this is not always the case and it is the task of the designer to be aware of the correct application of the time of concentration. It is noted that the time of concentration as used in the Rational Method is not the same as the critical storm duration or time to peak as determined from runoff-routing models. It is therefore inappropriate to adopt the critical storm duration determined from a runoff-routing model and apply it as the time of concentration for a Rational Method analysis. In certain circumstances, partial area effects need to be considered for a catchment and these are discussed in Section 4.03.2. In determining the time of concentration, the designer should adopt the appropriate catchment conditions in accordance with the required analysis. Ultimate flow conditions should be based on a fully developed catchment in accordance with the allowable land use shown in the relevant Strategic Plan, or as directed by the local authority. The following discussion is relevant to the application of the Rational Method. In a typical urban drainage system a designer will need to calculate time of concentration for two purposes: (i) To allow calculation of the runoff from sub-catchments in order to determine the position and size of inlets required to satisfy criteria such as flow-width (in the case of a Minor Storm) or roadway discharge capacity (in the case of a Major Storm). This time of concentration is known as the inlet time. To size a pipe or channel draining a number of sub-catchments based upon the total area of the sub-catchments contributing to the upstream end of the drain and the time of concentration of that area.

(ii)

4-17

Queensland Urban Drainage Manual volume 1 second edition 2007

4.06.2

Minimum time of concentration

Although travel time from individual elements of a system may be as short as two minutes, the total nominal flow travel time to be adopted from any catchment to its point of entry into the drainage network should not be less than 5 minutes.

4.06.3

Methodology for various urban catchments

By its nature the Rational Method is a very simple hydrologic model that depends on its original development and calibration to achieve reasonable flow estimation values for catchments of typical shape and surface condition. This equation addresses variations in rainfall loss, surface storage, and the rate (speed) of surface runoff in a very simplistic manner. Within the Rational Method both the runoff coefficient and the time of concentration are adjusted to account for typical variations in catchment conditions as described below: (i) The runoff coefficient (C) takes account of variations in catchment porosity, and hence the selection of this coefficient is usually related to the fraction impervious. The runoff coefficient (C) also takes account of variations in rainfall losses relative to the total rainfall intensity/volume, and thus the coefficient is adjusted using the frequency factor (FY). The average rainfall intensity (I) takes account of variations in the average rainfall intensity through the use of time of concentration. Indirectly, the average rainfall intensity (I) may also take account of typical variations in channel storage through variations in the methodology used to calculate the time of concentrationthus the method used to calculate tc varies with the type and size of catchment.

(ii)

(iii) (iv)

To apply the Rational Method in an appropriate and consistent manner, five different methodologies for determination of the time of concentration are presented below for different types of drainage catchments. Those catchment types being: (a) Predominantly piped or channelised urban catchments less than 500ha with the top of the catchment being urbanised. (b) Predominantly piped or channelised urban catchments less than 500ha with the top of the catchment being bushland or a grassed park. (c) Bushland catchments too small to allow the formation of a creek with defined bed and banks. (d) Urban creeks with a catchment area less than 500 ha. (e) Rural catchments less than 500ha.

4-18

Queensland Urban Drainage Manual volume 1 second edition 2007

(a) Predominantly piped or channelised urban catchments less than 500ha with the top of the catchment being urbanised. Components of time of concentration: (i) Standard Inlet Time (preferred) from Section 4.06.4. Alternatively calculate travel time from roof to kerb using Section 4.06.5. The standard inlet time includes the travel time along a typical length of kerb/channel from near the top of the catchment to the first pipe or channel inlet. If the actual length of kerb/channel travel is unusually long, then an additional travel time must be added to the standard inlet time (step (ii) below). If a gully/field inlet does not exist near the top of catchment, then use Sections 4.06.5 and/or 4.06.6 to determine the initial travel time to the start of the kerb/channel, then add the travel time along the kerb/channel. (ii) (iii) Kerb flow time from Figures 4.10 and 4.11 only if the length of kerb exceeds that which would normally exist at the top of a catchment. Pipe flow time using actual flow velocities determined from a pipe network analysis or Manning Equation. Alternatively, if the pipe flow time is not critical, an average pipe flow velocity of 2 m/s and 3 m/s may be adopted for low gradient and medium to steep gradient pipelines respectively. Creek and/or channel flow time using actual flow velocity determined from numerical modelling or the Manning Equation (not values from Table 4.06.5). Alternatively, if the expected travel time in the creek is not critical, an average flow velocity of 1.5 m/s may be adopted (not applicable to constructed channels).

(iv)

(b) Predominantly piped or channelised urban catchments less than 500ha with the top of the catchment being bushland or a grassed park. Components of time of concentration: (i) Estimate the length of sheet runoff at top of catchment using Table 4.06.3 or field observations, then estimate the sheet flow travel time as per Section 4.06.6. Determine the remaining distance of assumed concentrated overland flow from the end of the sheet runoff to the nearest kerb, pipe inlet, open channel or creek. Then determine the travel time for this concentrated overland flow based on the calculated flow velocity. Kerb flow time as per Figures 4.10 and 4.11. Pipe flow time using actual flow velocities determined from a pipe network analysis or Manning Equation. Alternatively, if the pipe flow time is not critical, an average pipe flow velocity of 2 m/s and 3 m/s may be adopted for low gradient and medium to steep gradient pipelines respectively. Creek and/or channel flow time using actual flow velocity determined from numerical modelling or the Manning Equation (not values from
4-19

(ii)

(iii) (v)

(vi)

Queensland Urban Drainage Manual volume 1 second edition 2007

Table 4.06.5). Alternatively, if the expected travel time in the creek is not critical, an average flow velocity of 1.5 m/s may be adopted (not applicable to constructed channels). (c) Bushland catchments too small to allow the formation of a creek with defined bed and banks. Time of concentration determined as for (b) above. (d) Urban creeks with a catchment area less than 500 ha. Time of concentration for an urban catchment containing a watercourse with defined bed and banks may be determined as for rural catchments (Section 4.06.11) but only if the following conditions apply: (i) channel storage along the watercoursefor the catchment condition being analysed is not significantly reduced from the natural (i.e. preurbanisation) conditions; and (ii) less than 20% of the catchment drains to a pipe network. If the above conditions do not apply, then the time of concentration should be based on the procedures outlined in (a) or (b) above as appropriate for the catchment conditions. Technical Note 4.06.1: Use of the Rational Method is generally not recommended for urban catchments greater than 500 hectares, or rural catchment greater than 25 km2. Hydrologic analysis of urban catchments greater than 500 hectares should be performed using a combination of suitable runoff routing modelling, and dynamic hydraulic modelling, using a range of storm durations. (e) Rural catchments less than 500 ha. Recommended procedures for the determination of the time of concentration for rural catchments as outlined in Section 4.06.11.

4-20

Queensland Urban Drainage Manual volume 1 second edition 2007

4.06.4

Standard inlet time

Use of standard inlet times for developed catchments is recommended because of the uncertainty related to the calculation of time of overland flow. The standard inlet time is defined as the travel time from the top of the catchment to a location where the first gully or field inlet would normally be expected as depicted in Figure 4.05.

Application of standard inlet time Figure 4.05

Recommended standard inlet times are presented in Table 4.06.1. These inlet times are considered appropriate for traditional (i.e. non WSUD) low density residential areas where the top of the catchment is low density residential, but not a park or bushland. If the top of the catchment consists of high density residential, then the local government should be consulted for inlet times appropriate for the catchment. In such cases it is recommended that the standard inlet time should not exceed 10 minutes unless demonstrated otherwise by the designer. If the hydrologic analysis is being performed on a development located at the top of the catchment, then use of a standard inlet time will usually not be appropriate because these inlet times are likely to be significantly greater than the actual travel time. If the first gully or field inlet is located further down the catchment slope than would normally be expected, then the standard inlet time shall only account for the travel time down to the location where the first gully or field inlet would normally have been located. If the urban drainage system does not incorporate pipe drainage (i.e. no gully or field inlet exists) then the standard inlet time shall extend down the

4-21

Queensland Urban Drainage Manual volume 1 second edition 2007

catchment to a location where a gully inlet would normally be located in a traditional kerb-&-channel drainage system. A standard inlet time should not be adopted in sub-catchments where detailed overland flow and kerb/channel flow calculations are justified.
Table 4.06.1 Recommended standard inlet times Location Road surfaces and paved areas Urban residential areas where average slope of land at top of catchment is greater than 15%. Urban residential areas where average slope of land at top of catchment is greater than 10% and up to 15%. Urban residential areas where average slope of land at top of catchment is greater than 6%and up to 10%. Urban residential areas where average slope of land at top of catchment is greater than 3% and up to 6%. Urban residential areas where average slope of land at top of catchment is up to 3%. Inlet Time (Minutes) 5 5 8 10 13 15

Note: The average slopes referred to are the slopes along the predominant flow path for the catchment in its developed state.

A local government may determine that the use of standard inlet times shall not apply within their area and may direct designers to use alternative methods. In certain circumstances the use of standard inlet times may result in times of concentration unacceptably short for the catchment under consideration, such as airports, or large flat car parks. In these cases the designer should utilise other methods (e.g. Friends Equation or the Kinematic Wave Equation) to determine the time of initial overland flow (refer to Section 4.06.6 below). Inlet times calculated by these methods should only be adopted for design if the sheet flow length criteria discussed in Section 4.06.6 are met and if due consideration is given to the type and continuity of the surface where overland flow is occurring. Notwithstanding the above, it is recommended that a maximum inlet time of 20 minutes be adopted for urban and residential catchments, including playing fields and park areas.

4-22

Queensland Urban Drainage Manual volume 1 second edition 2007

4.06.5

Roof to main system connection

In cases where use of a standard inlet time is not considered appropriate, the following roof to main system flow travel times are recommended:
Table 4.06.2 Recommended roof drainage system travel times Development Category Rural Residential, Residential Low Density For the roof, downpipes and pipe connection system from the building to the kerb and channel or a rear-of-allotment drainage system (Figure 4.06(a)). Residential Medium and High Density, Commercial, Industrial and Central Business For the roof and downpipe collection pipe to the connection point to the internal allotment drainage system abutting the building (Figure 4.06(b)). Time to point A (minutes) 5

Note: The flow time from point A (Figure 4.06) through the internal allotment pipe system to the kerb and channel, street underground system or rear of allotment system for the more intense developments noted should be calculated separately.

Typical Roof Drainage Systems Figure 4.06 (a) Residential Note: Point A is referred to in Table 4.06.2 Figure 4.06 (b) Industrial

4-23

Queensland Urban Drainage Manual volume 1 second edition 2007

4.06.6
(a)

Overland flow

General

Overland flow at the top of a catchment will initially travel as sheet flow, after which it will move down the catchment as minor concentrated flow. Travel times for the sheet flow and concentrated flow components need to determined separately. The sheet flow travel time is defined as the travel time from the top of a catchment to the point where stormwater runoff begins to concentrate against fences, walls, gardens, or is intercepted by a minor channel, gully or piped drainage. This concentration of flow may also occur in the middle of vegetated areas as the stormwater concentrates in minor drainage depressions. The time required for water to flow over a homogeneous surface such as lawns and gardens is a function of the surface roughness and slope. There are a number of methods available for the determination of sheet flow travel times and a local government may direct which of these methods shall be applied. Two such methods are presented in this section. Irrespective of which method of calculation is adopted, it is the designers responsibility to determine the effective length of this sheet flow. In urban areas, the length of overland sheet flow will typically be 20 to 50 metres, with 50 metres being the recommended maximum. In rural residential areas the length of overland sheet flow should be limited to 200m (Argue 1986), however the actual length is typically between 50 and 200m whereafter the flow will be concentrated in small rills, channels, or tracks. (b) Design steps

To determine the overland flow travel time the following steps should be applied: (i) Where practical, inspect the catchment to determine the length of initial overland sheet flow, or for new developments measure the length of overland flow from the design plans. Where it is not practical to inspect the catchment, determine the likely length of overland sheet flow based on Table 4.06.3. Determine the sheet flow travel time using either the Friends Equation (Equation 4.06 preferred method) or the Kinematic Wave Equation (Equation 4.07). Determine or measure the remaining distance of assumed concentrated overland flow from the end of the adopted sheet flow to the nearest kerb, channel, or pipe inlet. Determine the concentrated flow travel time using either Figure 4.09 or the Manning Equation.
4-24

(ii) (iii)

(iv)

(v)

Queensland Urban Drainage Manual volume 1 second edition 2007

Table 4.06.3 Recommended maximum length of overland sheet flow Surface Condition Steep (say >10%) grassland (Hortons n = 0.045) Steep (say >10%) bushland (Hortons n = 0.035) Medium gradient (approx. 5%) bushland or grassland Flat (01%) bushland or grassland Assumed Maximum Flow Length (m) 20 50 100 200

(c)

Friend's Equation/Nomograph for Overland Sheet Flow Time (Preferred Method for Overland Flow Calculation)

The formula shown below and attributed to Friend (1954) may be used for determination of overland sheet flow times. This was derived from previous work in the form of a nomograph for shallow sheet flow over a plane surface. (Figure 4.07). It is recommended that this procedure be adopted in preference to that given in Section 4.06.6 (d). Friend's Equation t = (107n L 0.333)/S 0.2 where t L n S = = = = overland sheet flow travel time (min) overland sheet flow path length (m) Hortons surface roughness factor slope of surface (%) (4.06)

Note: Values for Hortons n are similar to those for Mannings n for similar surfaces.

Overland Sheet Flow Times Shallow Sheet Flow Only (source: ARR-1977) Figure 4.07

4-25

Queensland Urban Drainage Manual volume 1 second edition 2007

(d)

Kinematic wave equation for overland sheet flow time

The Kinematic Wave Equation for overland travel time developed by Ragan & Duru (1972) may also be used; however, it should only be applied to planes of sheet flow which are homogenous in slope and roughness. Thus, travel times need to be determined separately for areas of different slope or roughness. As shown by McCuen (1984) it cannot be applied to large heterogeneous catchments. The kinematic wave equation is best applied to large paved areas such as car parks and airports. t where t L n* I S = = = = = = 6.94 (L.n*) 0.6 /(I 0.4.S 0.3) overland travel time (min) overland sheet flow path length (m) surface roughness/retardance coefficient rainfall intensity (mm/hr) slope of surface (m/m) (4.07)

Typical values for n* are: (i) As quoted by Argue (1986) p.28. Paved surfaces Lawns Thickly grassed surfaces = 0.015 = 0.25 = 0.50

(ii)

As derived from ARR (1998), Book 8, Table 1.4.

Table 4.06.4 Surface roughness or retardance factors Surface Type Concrete or Asphalt Bare Sand Gravelled Surface Bare Clay-Loam Soil (eroded) Sparse Vegetation Short Grass Paddock Lawns Hortons Roughness Coefficient n* 0.010 0.013 0.010 0.016 0.012 0.030 0.012 0.033 0.053 0.130 0.100 0.200 0.170 0.480

Notes (Table 4.06.4): 1. The surface roughness/retardance coefficient n* is similar but not identical to Mannings n value for surface roughness. 2. For further details of this procedure reference should be made to Technical Note 3, Book 8, ARR (1998). 3. Experience both locally and as quoted by McCuen (1984) indicates that the Kinematic Wave Equation tends to result in excessively long overland sheet flow travel times.

4-26

Queensland Urban Drainage Manual volume 1 second edition 2007

Based on rainfall intensity = 125mm/hr. Note: e.g. The boundary X-X defines the practical limit of SHEET FLOW path length on grass or unpaved surfaces. for 0.20 grassed slopes = 50m for 0.05 grassed slopes = 120m

Pervious surface flow distances exceeding these limits should be treated as natural channel flow. Flow velocity should be determined using the Mannings equation based on expected operating conditions.

Overland sheet flow times using kinematic wave equation (Source: Argue, 1986) Figure 4.08

4-27

Queensland Urban Drainage Manual volume 1 second edition 2007

4.06.7 Initial estimate of kerb, pipe and channel flow time

An initial (trial) estimate of flow time can be determined from Figure 4.09. The chart may be used directly to determine approximate travel times along a range of rigid channel types and, with the application of multiplier for a range of loose-boundary channel forms. Once a trial flow rate has been determined, the travel time determined from Figure 4.09 will need to be checked using either Figures 4.10 or 4.11.

Flow travel time in pipes and channels (Source: Argue, 1986) Figure 4.09
NOTES (Figure 4.09): 1. Flow travel time (approximate) may be obtained directly from this chart for: kerb-and-gutter channels stormwater pipes allotment channels of all types (surface and underground) drainage easement channels (surface and underground) 2. Multiplier , should be applied to values obtained from the chart as per: grassed swales, well maintained and without driveway crossings blade-cut earth table drains, well maintained and no driveway crossings natural channels
4-28

=4 =2 =3

Queensland Urban Drainage Manual volume 1 second edition 2007

4.06.8 Kerb flow

Time of flow in kerb and channel should be determined by dividing the length of kerb and channel flow by the average velocity of the flow. The average velocity of the flow may be determined in either of two ways: (i) Izzards Equationrefer to Technical Note 4, Book 8, ARR (1998). Reference is also made to Section 7.04.2 (c) of this Manual for a more detailed explanation of Izzards Equation. Figure 4.11 provides a quick solution to Izzards Equation, accurate enough for travel time calculations. Using Figure 4.10.

(ii)

FORMULA where

t t

= =

0.025 L / S 0.5

(minutes)

time of gutter flow in minutes length of gutter flow in metres slope of gutter (%)

L = S = EXAMPLE

Length of gutter flow = 100m Average slope of gutter = 3% Time of travel = 1.5 minutes.

Kerb and channel flow time using Mannings equation Figure 4.10

4-29

Queensland Urban Drainage Manual volume 1 second edition 2007

Kerb and channel flow velocity using Izzards equation Figure 4.11

4-30

Queensland Urban Drainage Manual volume 1 second edition 2007

4.06.9 Pipe flow

Wherever practical, pipe travel times should be based on calculated pipe velocities either using a Pipe Flow Chart (e.g. n = 0.013 for concrete pipes), uniform flow calculations using the Manning equation (Equation 4.08), or results from a calibrated numerical drainage model. An initial (trial) assessment of the pipe flow travel time can be determined using Figure 4.09. Alternatively, if the travel time within the pipe is small compared to the overall time of concentration, then an average pipe velocity of 2 m/s and 3 m/s may be adopted for low gradient and medium to steep gradient pipelines respectively.

4.06.10 Channel flow

The time stormwater takes to flow along an open channel may be determined by dividing the length of the channel by the average velocity of the flow. The average velocity of the flow is calculated using the hydraulic characteristics of the open channel. Mannings Equation is suitable for this purpose: V From which where t V n R S L t = = = = = = = = R 2/3. S 1/2/n L/(60.V) = n . L / 60 (R 2/3. S 1/2 ) average velocity (m/s) Mannings roughness coefficient hydraulic radius (m) friction slope (m/m) length of reach (m) travel time (min) (4.08) (4.09)

Where an open channel has varying roughness or depth across its width it may be necessary to sectorise the flow and determine the average flow velocity, to determine the flow time. Grass swales Flow travel times along grassed swales can vary significantly depending on flow depth and swale roughness. The effective swale roughness should be determined from vegetation retardance charts (Department of Main Roads, 2002). For a grass length of 50 to 150mm, typical Mannings roughness values may be interpolated from Table 9.03.4.

4-31

Queensland Urban Drainage Manual volume 1 second edition 2007

4.06.11 Time of concentration for rural catchments

For rural catchments the time of concentration can be found by using (a) Bransby-Williams equation, (b) the Modified Friends equation, or (c) application of the Stream Velocity Method. The local authority should be consulted for acceptability of a particular method. Note; that the initial overland flow travel time is incorporated into the Bransby-Williams and Modified Friends equations, thus an overland flow or standard inlet time should not be added. (a) where: tc = L = A = Se = (b) where: tc = L = Ch = R = = RS = n = A = Se = Bransby-Williams equation (preferred method for ease of use) tc = 58 L /( A 0.1. Se 0.2) (4.10)

the time of concentration (min) length (km) of flow path from catchment divide to outlet catchment area (ha) equal area slope of stream flow path (%) as defined in Figure 4.12. Modified Friends equation (Maximum Catchment Area 25 km2) tc = 800 L /( Ch . A 0.1. Se0.4) (4.11)

time of concentration (min) Length (km) of flow path from catchment divide to outlet Chezys coefficient at the site = R 1/6/n hydraulic radius = 0.75RS where stream slope is fairly uniform 0.65RS where stream slope varies appreciably along the stream hydraulic radius at the initially assumed flood level at the site average Manning roughness coefficient for the entire stream length catchment area (ha ) equal area slope of stream flow path (%) as defined in Figure 4.12.

The calculation of hydraulic radius is based upon the peak level of the design flood at the site in question. If later hydraulic calculations show this level to be in error by more than 0.30.6m, the value should be recalculated. Note; the units used in the above equations are different from those used within the 1992 edition. The adopted coefficients have been rounded down from the exact unit conversion to reflect the accuracy of the equations.

4-32

Queensland Urban Drainage Manual volume 1 second edition 2007

Derivation of the equal area slope (Se) of main stream Figure 4.12

(c)

Stream velocity method

As the catchment area increases, the relative influence of minor surface storage and instream channel storage on the peak discharge typically increases. To account for the flow-attenuating effects of channel/floodplain storage, the adopted or assumed stream velocity is less than the actual stream velocity, especially for low gradient streams where channel and floodplain storage is expected to be significant. For steep gradient or channelised streams with little or no floodplain storage the assumed stream velocity is close to the expected actual stream velocity.
Table 4.06.5 Assumed average stream velocities for catchment areas <500 ha [1] Type of Country Flat Rolling Hilly Steep Very Steep Rocky Mountains Average Slope of Catchment Surface (%) [2] 0 to 1.5 1.5 to 4 4 to 8 8 to 15 > 15 Assumed Stream Velocity (m/s) [3] 0.3 0.7 0.9 1.5 3.0

Notes: [1] Source: Book 4, Australian Rainfall and Runoff (1998). [2] Catchment slope is not the same as stream slope or equal area slope. [3] These are assumed average stream velocities that need to be adopted in order to determine an appropriate time of concentration for use in the Rational Method.

4-33

Queensland Urban Drainage Manual volume 1 second edition 2007

4.07 Intensity-frequency-duration data

This data is required as input to the hydrologic model used for design. There are a number of means by which this data can be obtained. (a) Local authorities may issue IFD curves and/or tables and direct that these be used within specified regions within their local authority area. (b) IFD data may be generated using the procedures given in ARR (1998) Book 2. Book 2 provides both algebraic and graphical procedures that allow the user to determine either complete or selected IFD design rainfall information for any location in Australia. The procedures enable the determination of rainfall intensities for durations of 5 minutes to 72 hours and ARIs from 1 year to 100 years. Book 2 also describes procedures for extrapolation to ARIs up to 500 years. The algebraic and graphical procedures are presented in ARR (1998) Book 2 as a series of eight steps which guide the user to obtain a complete matrix of rainfall intensities for selected durations and ARIs. The determination of design rainfall intensities using the above steps and the maps of ARR (1998) Volume 2 can be summarised as: (i) (ii) select the region of Queensland for the required location using the index to maps; read the log-normal design rainfalls for the basic ARIs of 2 and 50 years and durations of 1, 12 and 72 hours for the required location from MAPs 1 to 6; read the appropriate skewness from the regionalised skewness map (MAPS 7b and 7c); read the short duration geographical factors F2 and F50 from MAPs 8 and 9 and calculate the 6 minute duration log-normal rainfall intensities for ARIs of 2 and 50 years; convert the log-normal rainfalls from (ii) and (iv) to log-Pearson Type III distribution estimates using algebraic or graphical procedures; to determine rainfall intensities for other durations and ARIs, use algebraic or graphical interpolation and extrapolation techniques.

(iii) (iv)

(v) (vi)

4-34

Queensland Urban Drainage Manual volume 1 second edition 2007

The AR&R Volume 2 (1998) maps applicable to Queensland are as follows:

Map No. 1.1 to 6.1 1.2 to 6.2 1.3 to 6.3 1.4 to 6.4 1.5 to 6.5 1.13 to 6.13 1.14 to 6.14 7b 7c 8 Description Design Rainfall Isopleths Design Rainfall Isopleths Design Rainfall Isopleths Design Rainfall Isopleths Design Rainfall Isopleths Design Rainfall Isopleths Design Rainfall Isopleths Regional Map of Average Coefficient of Skewness Regional Map of Average Coefficient of Skewness Region Covered North Coast North Central Coast Central Coast South Central Coast South East West, North West & Far North South West North and West South West and South East

Contours of F2 for determining 6 minute rainfall intensities from 60 minute intensities for an ARI of 2 yrs. Whole State Contours of F50 for determining 6 minute rainfall intensities from 60 minute intensities for an ARI of 50 yrs. Whole State

Computer programs are available to generate IFD tables using the above input data from ARR. (c) IFD Curves for specific locations can be obtained from the Bureau of Meteorology. The Bureau will also provide tabulated data, a polynomial equation and coefficients for this equation. The equation can be used to generate a more detailed IFD table. (d) The shortest duration for which IFD data is normally available is 5 minutes. A procedure for estimating rainfall intensity data for shorter durations has been developed by Kennedy and Minty (1992).

4-35

Queensland Urban Drainage Manual volume 1 second edition 2007

4.08 Estimation of runoff volume

In stormwater design, the estimation of runoff volume is often as important as the estimation of peak discharge. Runoff volume is used for a variety of purposes including: (i) sizing certain construction site sediment basins; (ii) sizing stormwater detention/retention basins; (iii) designing many urban stormwater treatment systems. In some cases it will be necessary to determine an average annual volumetric runoff coefficient (CV), while in other design procedures it will be necessary to determine the volumetric runoff coefficient for a single storm event. The volumetric runoff coefficient for a single storm event can be used to estimate the runoff volume for the design storm. Table 4.08.1 summarises the various applications of these two forms of volumetric runoff estimation.
Table 4.08.1 Application of runoff volume estimation to stormwater design Annual Runoff Design Activity Application or Single Event Temporary construction site sediment basins Permanent sedimentation basins Stormwater detention and retention basins Urban stormwater design Single event storm Sizing temporary construction site (wet) basins. Performance analysis of a basin following an actual storm event. Annual runoff volume Single event storm Annual runoff volume Sizing off-stream sedimentation basins for water quality purposes. Determination of the basins desired peak outflow to avoid increases in downstream flood levels (Chapter 6.04). Design of new land developments to minimise changes in runoff volume so that the risk of downstream creek erosion is minimised. Sizing a stormwater treatment device for a specified design storm.

Single event storm

Estimating the volume of runoff from a single storm requires different procedures to those used to determine the average annual volumetric runoff coefficient.

4-36

Queensland Urban Drainage Manual volume 1 second edition 2007

4.08.1 Use of the volumetric runoff coefficient

The volumetric runoff coefficient (CV) is defined as the ratio of the volume of stormwater runoff to the volume of rainfall that produced the runoff. When reference is made to the volumetric runoff coefficient the following facts should be noted: (i) (ii) The volumetric runoff coefficient is not the same as the Rational Method coefficient of discharge (C). The volumetric runoff coefficient for a single storm event will almost certainly be different from the average annual volumetric runoff coefficientthe latter being a ratio of average annual runoff to average annual rainfall.

Given point (ii) above, if a reference is made to an assessed volumetric runoff coefficient, or a coefficient determined from a design guideline, then it is important to acknowledge whether the coefficient refers to a single storm event, or to an annual average.

4.08.2 Estimation of average annual runoff volume

The average annual runoff volume may be determined from continuous catchment modelling (preferred method), or through the use of a calibrated regional volumetric runoff coefficient. The average annual volumetric runoff coefficient for a given catchment will depend on the following factors: soil permeability; local hydrology; percentage of directly connected impervious area; percentage of indirectly connected impervious surface area; degree of stormwater harvesting, including the use of rainwater tanks. Local hydrology can also affect the volumetric runoff coefficient. In tropical regions high intensity storms can represent a greater percentage of total annual rainfall causing an increase in the coefficient relative to those used in temperate zones. An estimation of the average annual volumetric runoff coefficient may be obtained using one of the following methods: (i) analysis of long-term stream gauging and rainfall records (first option) (ii) continuous water balance modelling using a calibrated catchment yield model (second option); (iii) use of an annual average volumetric runoff coefficient (third option). The annual average volumetric runoff coefficient may also be determined from analysis of continuous stream gauging records, such as the gauging
4-37

Queensland Urban Drainage Manual volume 1 second edition 2007

stations operated by the Department of Natural Resources and Water. Councils are encouraged to establish low-flow gauging stations within their region to assist in the development of local data for model calibration. Guidelines on continuous event modelling may be found in Chapter 14 of ARQ and post-1998 versions of Australian Rainfall and Runoff.

4.08.3 Estimation of runoff volume from a single design storm

An estimation of runoff volume from a single storm event may be obtained using one of the following methods: (i) calibrated runoffrouting model (preferred method); (ii) use of the single storm event volumetric runoff coefficient (Table 4.08.2); (iii) direct extraction of estimated rainfall losses from a given rainfall hyetograph; (iv) estimation of runoff volume based on the Rational Method peak discharge (preliminary design use only). It is noted that the actual runoff volume will be dependent on a number of variables including soil type, depth of soil, land slope, type and density of vegetation cover, and the degree soil moisture at the start of the storm event (i.e. the lasting effects of previous rainfall). (a) Single event volumetric runoff coefficient

The volumetric runoff coefficient (CV) for a single storm event may be estimated using the U.S. Soil Conservation Service (1986) procedures. Volumetric runoff coefficients developed from these procedures are presented in Table 4.08.2. The coefficients presented in Table 4.08.2 apply only to the pervious surfaces, therefore an adjustment must be applied to determine a coefficient for urbanised catchments, as presented in Equation 4.12.

4-38

Queensland Urban Drainage Manual volume 1 second edition 2007

Table 4.08.2 Typical single storm event volumetric runoff coefficients for various soil hydrologic groups Rainfall (mm) 10 20 30 40 50 60 70 80 90 100 Group A Sand 0.02 0.02 0.08 0.16 0.22 0.28 0.33 0.36 0.41 0.45 Soil Hydrologic Group Group B Group C Sandy Loam Loamy Clay 0.10 0.09 0.14 0.24 0.34 0.42 0.48 0.53 0.57 0.60 0.63 0.27 0.42 0.52 0.58 0.63 0.67 0.70 0.73 0.75 Group D Clay 0.20 0.43 0.56 0.63 0.69 0.74 0.77 0.79 0.81 0.83

Source: US Soil Conservation Service (1986) Group A soils: soil with very high infiltration capacity. Usually consist of deep (> 1m), well-drained sandy loams, sands or gravels. Group B soils: soil with moderate to high infiltration capacity. Usually consist of moderately deep (>0.5m), well-drained medium loamy texture sandy loams, loams or clay loam soils. Group C soils: soil with a low to moderate infiltration capacity. Usually consist of moderately fine clay loams, or loamy clays, or more porous soils that are impeded by poor surface conditions, shallow depth or a low porosity subsoil horizon. Group D soils: soil with a low porosity. Usually consists of fine-texture clays, soils with poor structure, surface-sealing (dispersive/sodic) soils, or expansive clays. Included in this group would be soils with a permanent high watertable.

Landcom (2004) provides typical infiltration rates for the various Soil Hydrological Groups (A, B, C, & D) as presented in Table 4.08.3.
Table 4.08.3 Typical infiltrations rates for various soil hydrological groups [1] Soil Hydrological Group A B C D Typical Infiltration Rate (mm/hr) Saturated 25 13 6 3 Dry Soil >250 200 125 75 Ksat (mm/hr) [2] >120 10120 110 <1

Notes: [1] Sourced from Landcom, 2004. [2] Ksat = Saturated hydraulic conductivity

4-39

Queensland Urban Drainage Manual volume 1 second edition 2007

CV ( composite ) =

CV ( pervous ) . A A(imp.) + A(imp.) A

(4.12)

where: CV (composite) = Composite volumetric runoff coefficient CV (pervious) = Volumetric runoff coefficient for pervious surface (Table 4.08.2) A = Total catchment area A (imp.) = Area of directly connected impervious surface, plus a percentage of the indirectly connected impervious surface area (assume 50% unless otherwise directed) If the coefficient is being determined for the design of a temporary construction site sediment basin established within a clayey or loamy soil catchment, then a volumetric runoff coefficient of 1.0 is recommended for all compacted soils and areas exposed to heavy construction traffic (unless otherwise directed within an recognised sediment basin design procedure). Otherwise, use values from Table 4.08.2, or adopt a value of 0.5 for pervious surfaces if the soil texture is not known. (b) Analysis of rainfall hyetograph

If adequate information is known about the effective loss rates (e.g. initial loss and continuing loss rate) for the catchments pervious and impervious areas, then a single storm event volumetric runoff coefficient can be estimated directly from a given rainfall hyetograph. However, it should be noted that design storms are not typical of a complete storm, they are at best a representation of a possible design storm burst likely to be found within a real storm. Thus, extreme care must be taken in the selection of an appropriate initial loss value. Unless otherwise nominated by the local authority, the adopted initial loss rate should reasonably reflect the vegetation density, groundcover/mulch density and soil porosity. Guidelines on the determination of storm losses are provided in Book 2 of ARR (1998). (c) Estimation of runoff volume using the rational method

A preliminary (not design) estimation of the runoff volume may be determined directly from the calculated peak discharge for the nominal design storm using Equation 4.13. This volume must be used with caution. where: Vi = (4/3) tc Qi (4.13)

Vi = runoff volume for the nominated storm event [m3] tc = time of concentration used to calculate Qi [s] Qi = peak discharge for the runoff hydrograph [m3/s]

4-40

Queensland Urban Drainage Manual volume 1 second edition 2007

4.09 Methods for assessing the effects of urbanisation on hydrologic models

Generally, the effects of urbanisation on runoff from a [drainage] basin include higher volume, higher peak discharge and shorter time of concentration. These changes are associated with the increased imperviousness and more efficient drainage that are characteristics of constructed drainage systems, (Hoggan 1989). Whilst it is not possible to provide firm recommendations in this Manual in respect of the effects of urbanisation, it is suggested that designers consider the following alternatives as applicable, and where appropriate refer to the sources. (a) Unit hydrograph methods

After Rao, Delleur and Sarma (1972). Catchment lag where A P D U = = = = = 1275. A 0.458 . D 0.371 . P 0.267 .(1 + U ) 1.662 catchment area (km2) depth of rainfall excess (mm) duration of rainfall excess (h) degree of urbanisation (fraction) (4.14)

Catchment lag is defined as the average time required for all parts of a catchment to contribute to the discharge at the outlet and includes allowance for both catchment storage and channel (or transmission) storage. A catchment where no account is taken of catchment storage effects has a lag time (or catchment lag) of tc/2. Including the effects of catchment storage gives a lag time of approximately 1.33 tc. (b) Runoff routing methods RAFTS After Aitken (1975) B where: B S = = = 0.285. A 0.52 . S 0.50 (1 + U ) 1.97 routing parameter for RAFTS Model modified equal area slope (%) (equivalent m = 0.715) (4.15)

4-41

Queensland Urban Drainage Manual volume 1 second edition 2007

(c) (i)

Runoff routing models RORB After Laurenson and Mein (1990) For use with RORB Model Fi . Li kri = d av

(4.16)

where: kri = relative delay time of storage i Li = reach length represented by storage i (km) Fi = a factor depending upon the type of reach For a natural channel reach Fi = 1.0 For a lined or piped reach Fi = 1/(9Sc 0.5) where (ii) Sc = slope of the channel reach (%) After Brisbane City Council, Carroll (1990) For use with RORB Model (m = 0.8) kc = where kc = dav = (d)

12 d av . (1 + U ) 2.0

(4.17)

empirical coefficient average distance of flow in the channel network of sub-area inflows (km)

Runoff routing models WBNM

After Boyd, Bufill & Knee (1993), Boyd & Milevski (1996) and Boyd, Rigby & VanDrie (1999). Calculates separate hydrographs from pervious and impervious areas. Different rainfall losses are specified for the two surfaces, and the hydrographs are combined at the subarea outlet. Runoff from pervious areas uses the standard WBNM lag equation: Pervious Lag = LagParam . Aper0.57.Q-0.23 (4.18)

where LagParam is the lag parameter for natural catchments, based on recorded flood data, with a recommended value of 1.6. Runoff from impervious areas uses a modified equation, based on recorded flood data from urban catchments: Impervious Lag = ImpLagFactor . LagParam . Aimp0.25
4-42

(4.19)

Queensland Urban Drainage Manual volume 1 second edition 2007

where ImpLagFactor reduces the lag time for runoff from impervious surfaces, with a recommended value of 0.10. The above equations apply to runoff from the pervious and impervious surfaces of the subarea. If the stream channel is itself modified, with increased flow velocities and hence reduced lag times, a reduced lag time can be applied to the watercourse: Stream Channel Lag = StreamLagFactor . LagParam . A0.57.Q-0.23 (4.20)

where StreamLagFactor reduces the lag time in the stream channel, depending on the flow velocity. For example, if the channel remains in essentially natural condition, StreamLagFactor has a value of 1.0, whereas concrete lining which may increase flow velocites 3 times, would have a StreamLagFactor of 0.33. All three equations are built into the model, and the user only has to specify values of LagParam, ImpLagFactor and StreamLagFactor. (e) Other

After Mein and Goyen (1988) This reference provides a useful summary of the effects of urbanisation.

4-43

Queensland Urban Drainage Manual volume 1 second edition 2007

4.10 References
Argue, J.R. 1986, Storm Drainage Design in Small Urban Catchments: A Handbook for Australian Practice. Special Report No. 34, Australian Road Research Board, Vermont South, Vic. Aitken, A.P. 1975, Hydrologic Investigation and Design of Urban Stormwater Drainage Systems, A.W.R.C. Technical Paper No. 10, Department of the Environment and Conservation, A.G.P.S., Canberra, A.C.T. Boyd, M.J., Bufill, M.C. and Knee, R.M.1993, Pervious and impervious runoff in urban catchments. Hydrological sciences Journal, Vol. 38, No. 6, pp. 200-220. Boyd, M.J. and Milevski, P. 1996, Modelling runoff from pervious and impervious surfaces in urban catchments. 7th International Conference on Urban Storm Drainage, Hannover Germany, pp.1055-1060. Boyd, M.J. Rigby, E.H. and VanDrie, R. 1999, Modelling urban catchments with WBNM. Instn. Engineers Australia, Water 99 Joint Congress. 25th Hydrology and Water Resources Symposium and 2nd International Conference on Water Resources and Environmental Research, National Conference Publication, ISBN 185 825 7165, Vol.2, pp.831-835. Carroll, D.G. 1990, Creek Hydraulics Procedure Manual, Brisbane City Council, Internal Report. Department of Main Roads 2002, Road Drainage Design Manual. Queensland Department of Main Roads, Brisbane. Hoggan, D.H. 1989, Computer-Assisted Floodplain Hydrology and Hydraulics, McGraw-Hill, New York. Institution of Engineers, Australia 1977, (ARR) Australian Rainfall and Runoff: Flood Analysis and Design, Canberra, A.C.T. Institution of Engineers, Australia 1998, (ARR) Australian Rainfall and Runoff: A Guide to Flood Estimation, Barton, A.C.T. Kennedy, M.R. and Minty, L.J. 1992, A Method for the Derivation of Rainfall Intensity-Frequency-Duration Data Below 5 Minutes, Proc. Int. Symp. on Urban Stormwater Management, Sydney, N.S.W. Landcom 2004, Managing Urban Stormwater: Soils and Construction Volume-1, Landcom, New South Wales Government, ISBN 0-9752030-3-7. Laurenson, E.M. and Mein, R.G. 1990, RORB - Version 3 Runoff Routing Program User Manual, 2nd Edition, Monash University, Department of Civil
4-44

Queensland Urban Drainage Manual volume 1 second edition 2007

Engineering and Association (A.C.A.D.S.), Melbourne, Vic.

of

Computer

Aided

Design

Studies

McCuen R.J., Wong, S.L. and Rawls, W.J. 1984, Estimating Urban Time of Concentration, Journal of Hydraulic Engineering, A.S.C.E., Vol. 110, No. 7. McMahon, G.M. and Muller, D.K. 1986, The Application of the Peak Flow Parameter Indifference Curve Technique with Ungauged Catchments, Hydrology and Water Resources Symposium, I.E. Aust., Canberra, A.C.T. Mein, R.G. and Goyen, A.G. 1988, Urban Runoff, I.E.Aust., Civil Engineering Transactions, Vol. CE30, No. 4. Natural Resources and Mines 2005, Soil Conservation Measures Design Manual for Queensland. Queensland Government, Department of Natural Resources and Mines, Brisbane. Ragan, R.M. and Duru, J.O. 1972, Kinematic Wave Nomograph for Times of Concentration. Journal of Hydraulics Division, A.S.C.E., Vol. 98 No. HY10. Rao, R.A., Delleur, J.W. and Sarma, B.S.P. 1972, Conceptual Hydrologic Models for Urbanising Basins, Journal of Hydraulics Division, A.S.C.E., Vol. 98, No. HY7. US Soil Conservation Service 1986, Urban Hydrology for Small Watershed. Technical Release 55. US Department of Agriculture. Weeks, W.D. 1986, Flood Estimation by Runoff Routing Model Applications in Queensland, Civil Engineering Trans, I.E. Aust., Canberra, A.C.T.

4-45