Location via proxy:   [ UP ]  
[Report a bug]   [Manage cookies]                

CAT 772G Torque Converter Lockup Clutch Leakage - Test

Download as pdf or txt
Download as pdf or txt
You are on page 1of 3

772G Off-Highway Truck LTS00001-UP (MACHINE) POWERED BY C18 Engine(SEB...

Page 1 of 3

Shutdown SIS

Previous Screen

Product: TRUCK
Model: 772G TRUCK LTS
Configuration: 772G Off-Highway Truck LTS00001-UP (MACHINE) POWERED BY C18 Engine

Testing and Adjusting


770G and 772G Off-Highway Truck Power Train
Media Number -UENR1123-02 Publication Date -01/09/2015 Date Updated -15/09/2017

i04254290

Torque Converter Lockup Clutch Leakage - Test


SMCS - 3115-036; 5073-036

Table 1
Tools Needed Qty
6V-3079 Pressure Hose Assembly 1
6V-4143 Coupler Assembly 1

Personal injury or death can result from sudden machine movement.

Sudden movement of the machine or release of air pressure or oil


pressure can cause injury to persons on or near the machine.

To help prevent possible injury before testing and adjusting any air
system or hydraulic system, perform the procedure in the Testing and
Adjusting, "General Information" section.

NOTICE

Care must be taken to ensure that fluids are contained during


performance of inspection, maintenance, testing, adjusting, and repair
of the product. Be prepared to collect the fluid with suitable containers

https://127.0.0.1:444/sisweb/sisweb/techdoc/techdoc_print_page.jsp?returnurl=/sisweb/si... 22/10/2023
772G Off-Highway Truck LTS00001-UP (MACHINE) POWERED BY C18 Engine(SEB... Page 2 of 3

before opening any compartment or disassembling any component


containing fluids.

Refer to Special Publication, NENG2500, "Dealer Service Tool


Catalog" for tools and supplies suitable to collect and contain fluids on
Cat products.

Dispose of all fluids according to local regulations and mandates.

This test will determine if there are bad seals in the lockup clutch.

Illustration 1 g02425238

View of the top of the transmission on the 770G

(1) Pressure tap for the modulating valve (torque converter lockup clutch)

(2) Modulating valve for the torque converter lockup clutch

https://127.0.0.1:444/sisweb/sisweb/techdoc/techdoc_print_page.jsp?returnurl=/sisweb/si... 22/10/2023
772G Off-Highway Truck LTS00001-UP (MACHINE) POWERED BY C18 Engine(SEB... Page 3 of 3

Illustration 2 g02425239

View of the top of the transmission on the 772G

(1) Pressure tap for the modulating valve (torque converter lockup clutch)

(2) Modulating valve for the torque converter lockup clutch

1. Connect the coupler and the hose to pressure tap (1). Place the other end of the hose into a
container.

2. Start the engine. Run the engine at a low idle rpm with the transmission in NEUTRAL.

3. Measure the amount of oil that comes out of pressure tap (1) in 1 minute. Install the fitting
when this check is complete.

Note: More than 3.8 L/min (1 US gpm) from the pressure tap may indicate bad seals in the lockup
clutch.

Copyright 1993 - 2023 Caterpillar Inc. Sun Oct 22 09:42:23 UTC+0400 2023
All Rights Reserved.
Private Network For SIS Licensees.

https://127.0.0.1:444/sisweb/sisweb/techdoc/techdoc_print_page.jsp?returnurl=/sisweb/si... 22/10/2023

You might also like