P6LU-xxxxE/ZH60ENLF Mainzer Straße 151–153

D-55299 Nackenheim
Tel. +49 6135 7026-0
PML-SERIES Fax: +49 6135 931070
Rev.06-2009
www.peak-electronics.de

1 Watt peak@peak-electronics.de

Unregulated

Single and Dual Output The PML series P6LU-xxxxE/ZH60ENLF is a family of cost effective 1 W
single & dual output DC-DC converters. These converters are in an ultra

SIP7 Case miniature SIP7 case without compromising performance. The bigger case

6 kV DC I/O Isolation ensures the physical clearance of isolation barrier of 2.5mm which
increases the reliability under high pot from 6kV DC. Devices are

Low Coupling Capacity encapsulated. High performance features: 6kV input/output isolation, high
efficiency, output voltage accuracy of ±3%, input range of ±10%, low

Rated Voltage for 250 Vrms output ripple and noise and long term short circuit protection.

All specifications typical at Ta=25°C, nominal input voltage and full load unless otherwise specified
Input Specifications
Voltage Range ± 10%
Input Filter Capacitor
Input Reflected Ripple Current¹ 20 mA pk-pk

Output Specifications
Voltage Accuracy ± 3%
Short Circuit Protection Indefinite (automatic recovery)
Line Regulation ± 1.2% / 1% Vin Change
Load Regulation (10% - 100%) ± 10%
Ripple and Noise (20Mhz bandwidth) 200 mV pk-pk
Temperature Coefficient ± 0.03% / °C

General Specifications
Efficiency See table
I/O Isolation Voltage (3 sec. flash test) 6000 VDC
I/O Isolation Capacity 10 pF, typ.
I/O Isolation Resistance 1000 M Ohm
Switching Frequency 20 - 50 kHz, typ.
Humidity 95% rel H
Reliability Calculated MTBF (MIL-HDBK-217F) >2.39 Mhrs
Safety Standard (designed to meet) IEC 60950-1:2001

Physical Specifications
Clearance Distance (Input to Output) 2.5 mm
Case Material Epoxy encapsulated (UL94V-0 rated)
Potting Material Epoxy (UL94V-0 rated)
Weight ~ 4.2g, typ.

Environment Specifications
Operating Temperature -40 to +85 °C (ambient)
Maximum Case Temperature 100°C
Storage Temperature -40 to +125°C
Cooling Free Air Convection (10 mm distance required)
RoHS Conform Soldering 260°C, max. (1.5 mm from case 10s.)

PML-Series – P6LU-xxxxE/ZH60ENLF – Single and Dual Output – SIP7 - Plastic Case

Specification can change without a notice – We accept no liability for any inaccuracy or printing errors.
Page 1/4
Selection Guide
Single Output

m A)
) o ad (
DC) VD C ul l L uF)²
a ge (V
l t a ge ( rrent F ( % ) L o ad (
t Vo
lt Vo Cu ienc
y
a c it
or
put pu t
Order # Inpu O ut O ut Effic Cap
SINGLE OUTPUT
P6LU-053R3EH60ENLF 5 3.3 303 69 - 75 220
P6LU-0505EH60ENLF 5 5 200 70 - 77 220
P6LU-0509EH60ENLF 5 9 111.1 70 - 80 220
P6LU-0512EH60ENLF 5 12 83.3 70 - 80 220
P6LU-0515EH60ENLF 5 15 66.7 70 - 80 220
P6LU-093R3EH60ENLF 9 3.3 303 69 - 75 220
P6LU-0905EH60ENLF 9 5 200 70 - 77 220
P6LU-0909EH60ENLF 9 9 111.1 70 - 80 220
P6LU-0912EH60ENLF 9 12 83.3 70 - 80 220
P6LU-0915EH60ENLF 9 15 66.7 70 - 80 220
P6LU-123R3EH60ENLF 12 3.3 303 69 - 75 220
P6LU-1205EH60ENLF 12 5 200 70 - 77 220
P6LU-1209EH60ENLF 12 9 111.1 70 - 80 220
P6LU-1212EH60ENLF 12 12 83.3 70 - 80 220
P6LU-1215EH60ENLF 12 15 66.7 70 - 80 220
P6LU-153R3EH60ENLF 15 3.3 303 69 - 75 220
P6LU-1505EH60ENLF 15 5 200 70 - 77 220
P6LU-1509EH60ENLF 15 9 111.1 70 - 80 220
P6LU-1512EH60ENLF 15 12 83.3 70 - 80 220
P6LU-1515EH60ENLF 15 15 66.7 70 - 80 220
P6LU-243R3EH60ENLF 24 3.3 303 69 - 75 220
P6LU-2405EH60ENLF 24 5 200 70 - 77 220
P6LU-2409EH60ENLF 24 9 111.1 70 - 80 220
P6LU-2412EH60ENLF 24 12 83.3 70 - 80 220
P6LU-2415EH60ENLF 24 15 66.7 70 - 80 220

If you need other specifications, please enquire.

PML-Series – P6LU-xxxxE/ZH60ENLF – Single and Dual Output – SIP7 - Plastic Case

Specification can change without a notice – We accept no liability for any inaccuracy or printing errors.
Page 2/4
Selection Guide
Dual Output

m A)
) o ad (
DC) VD C ul l L uF)²
a ge (V
l t a ge ( r re nt F ( % ) L o ad (
t Vo
lt Vo Cu ie n c
y
acit
or
pu t put
Order # Inpu O ut O ut Effic Cap
DUAL OUTPUT
P6LU-053R3ZH60ENLF 5 ± 3.3 ± 151.5 68 - 75 ± 100
P6LU-0505ZH60ENLF 5 ±5 ± 100 70 - 78 ± 100
P6LU-0509ZH60ENLF 5 ±9 ± 55.6 70 - 81 ± 100
P6LU-0512ZH60ENLF 5 ± 12 ± 41.7 72 - 81 ± 100
P6LU-0515ZH60ENLF 5 ± 15 ± 33.3 70 - 81 ± 100
P6LU-093R3ZH60ENLF 9 ± 3.3 ± 151.5 68 - 75 ± 100
P6LU-0905ZH60ENLF 9 ±5 ± 100 70 - 78 ± 100
P6LU-0909ZH60ENLF 9 ±9 ± 55.6 70 - 81 ± 100
P6LU-0912ZH60ENLF 9 ± 12 ± 41.7 72 - 81 ± 100
P6LU-0915ZH60ENLF 9 ± 15 ± 33.3 70 - 81 ± 100
P6LU-123R3ZH60ENLF 12 ± 3.3 ± 151.5 68 - 75 ± 100
P6LU-1205ZH60ENLF 12 ±5 ± 100 70 - 78 ± 100
P6LU-1209ZH60ENLF 12 ±9 ± 55.6 70 - 81 ± 100
P6LU-1212ZH60ENLF 12 ± 12 ± 41.7 72 - 81 ± 100
P6LU-1215ZH60ENLF 12 ± 15 ± 33.3 70 - 81 ± 100
P6LU-153R3ZH60ENLF 15 ± 3.3 ± 151.5 68 - 75 ± 100
P6LU-1505ZH60ENLF 15 ±5 ± 100 70 - 78 ± 100
P6LU-1509ZH60ENLF 15 ±9 ± 55.6 70 - 81 ± 100
P6LU-1512ZH60ENLF 15 ± 12 ± 41.7 72 - 81 ± 100
P6LU-1515ZH60ENLF 15 ± 15 ± 33.3 70 - 81 ± 100
P6LU-243R3ZH60ENLF 24 ± 3.3 ± 151.5 68 - 75 ± 100
P6LU-2405ZH60ENLF 24 ±5 ± 100 70 - 78 ± 100
P6LU-2409ZH60ENLF 24 ±9 ± 55.6 70 - 81 ± 100
P6LU-2412ZH60ENLF 24 ± 12 ± 41.7 72 - 81 ± 100
P6LU-2415ZH60ENLF 24 ± 15 ± 33.3 70 - 81 ± 100

If you need other specifications, please enquire.

PML-Series – P6LU-xxxxE/ZH60ENLF – Single and Dual Output – SIP7 - Plastic Case

Specification can change without a notice – We accept no liability for any inaccuracy or printing errors.
Page 3/4
Package / Pinning / Derating

2.13
(0.08)

All dimensions are typical in millimeters (inches).

- Pin diameter: 0.5 +/-0.05 (0.02 +/-0.002)
- Pin pitch tolerance: +/-0.35 (+/-0.014)
- Case tolerance +/-0.5 (+/-0.02)
Specification may change without notice.
0.50 0.50
(0.02) (0.02)
9.80
19.50 (0.39)
(0.76)

PEAK
Modelcode
Datecode
1 2 5 6 7

2.54
(0.10)
15.24 SIP7 – „ENLF“ PLASTIC CASE
(0.60)

PIN CONNECTIONS
# SINGLE DUAL
1 +Vin +Vin
2 - Vin - Vin
5 - Vout - Vout
6 Omitted Common
7 +Vout +Vout

App Notes:
¹ = Measured Input reflected ripple current with a simulated source inductance of 12uH.
² = Tested by minimal Vin and constant resistive load.

- Operation under no-load conditions will not damage these devices, but they will not observe the listed specifications.

- For reduce converter’s ripple & noise, it is recommended to add a 4.7µF~100µF(±4.7µF~±68µF for dual output) capacitor at
the output. For EMI performance improvement, it is recommended to add a 12µH inductor and a 10µF~100µF capacitor at the
input.

PML-Series – P6LU-xxxxE/ZH60ENLF – Single and Dual Output – SIP7 - Plastic Case

Specification can change without a notice – We accept no liability for any inaccuracy or printing errors.
Page 4/4