PZR KV 1 - Operation Manual

LIYU PZR-KV-1 Series High Speed
Inkjet Printer
First edition September 15th, 2015
Second edition March 3rd, 2016
Copyright © 2015 All rights reserved for LIYU DMS GmbH
LIYU DMS GmbH has the right to revise the technical specification and various contents in the
manual without any notice and shall not be liable for any damages (including causal damages)
due to reliance on the contents in the manual (including such mistakes as misprints,
miscalculation and list errors).
Introduction
Thank you very much for purchasing our LIYU PZR-KV-1 series high speed inkjet printer
(hereinafter referred to as printer). Please carefully read the manual before using the printer and
put the manual at the place within easy reach at any time.
The operational manual describes the features of the printer, parts name, information that should
be known before using the equipment and the basic operation, for instance, how to switch on and
off and how to set various parameters of the printer.
Please carefully read the following contents before reading Chapter One:
Standard accessories
Safety precautions
Operation precautions
Technical Specifications
PZR-KV-1series high speed inkjet printer uses KONICA KM512iLNB type print head, with the
following main categories:
List of machine models:

Model Description Features
Adopts KM512iLNB type print head, with 4 Maximum Resolution: 1440dpi,

PZR3204-KV-1 with fast printing speed and
colors and 4 print heads wider range of print media.
Adopts KM512iLNB type print head, with 4 Maximum Resolution: 1440dpi,

PZR3208-KV-1 with faster printing speed and
colors and 8 print heads wider range of print media.
LIYU-PZR-KV-1-Series Manual www.liyu-dms.com -2-

List of main technical specifications:

Basic specification
Machine Model PZR3208-KV-1 PZR3204-KV-1
Print Tech. Piezo continuous drop-on demand(DOD)
Print Head KM512iLNB (30pl)
Head Quantity 8 4
Maximum Printing
3.2m/126in
Size
Resolution 30pl:720 x 1440. Note 1
Ink Type Eco-solvent ink
Color Profile KCMY
Ink Supply System Automatic continuous ink supply with vacuum negative pressure
Flexible roll medium (ordinary light box cloth, post-it note, vehicle body
Media Type
transparent sticker and so on)
Take-up and feeding Automatic take-up and feeding system, double-roller feeding system for
system standard configuration.
Media Absorption Table vacuum absorption, segmented control and adjustable suction
Table Pressure 50kg/m2
Packing Size(w×d×
5.00m x 1.08m x 1.77m
h)
Gross Weight of
750kg
Equipment
Interface USB2.0
Power Requirement 110V / 220±10%, ＞30A, 50 / 60Hz
Environmental
Temperature 15 0C ~ 28 0C Relative humidity 40% ~ 80%
Requirements
Durability Two years outdoor

Note 1：
The control software can add resolution for the equipment according to certain rules and the
above maximum resolution is tested by our company to fully meet the customers’ needs.

Printing efficiency list
The printing efficiency of PZR-KV-1series high speed inkjet printer only relates to the print head
type and head quantity in theory. However, other reasons may also lead to decline of actual
printing efficiency, such as low operation speed of computer, small width of printing materials
etc.
Print head KM512iLNB (30pl)
Head Quantity 4 8
Draft Mode
(2PASS)
135m2/h 240m2/h
Production Mode
(3PASS)
100m2/h 170m2/h
Quality Mode
(4pass)
80m2/h 130m2/h

Machine optional components
Optional Components Functional Description Configuration Method
Automatic Measuring It can automatically measure the medium width Upgradeable

Device and feeding position under command and
arrange simple composition of printing image
according to measuring results (page margin
print or centering print can be set).
Single Roller Feeding Double-roller feeding system is applied to Configure to Order

Device standard configuration, while single roller
feeding system can also be optional.
Heating Function of Print Heating function of print head bottom plate is Configure to Order
head Bottom Plate not applied to standard configuration, while it
can also be optional.
Black cloth detecting function is not applied to Configure to Order

Black Cloth detecting
Function standard configuration, while it is optional.
Note:
Upgradeable: The components can be upgraded for customers afterwards.
Configure to Order: Since the upgrading of the device requires grate working quantity or could
not be done in future, these devices shall be determined when placing the order.

Standard accessories
Standard accessories include the essential accessories for the machine and additional fittings.
Please refer to the attachment Packing List for detailed information.

Important particulars
The negligence of precautions mentioned below may seriously affect the working conditions of
the equipment, equipment service life or the service life of relevant parts, or even cause the
permanent damages of relevant parts, and may endanger staff’s physical and mental health in
some cases. Please operate in strict accordance with instructions.
1. Keep ink and ink route system away from water or any water-based liquid.
2. Please use the ink designated by the manufacturer and ensure that the ink is within the
guarantee period, otherwise, it may affect the printing effects or even cause the permanent
damage of print head.
3. Please carefully read the requirements for working space and working environment of the
machine in this manual and strictly abide by the requirements,. Otherwise, it will affect the
working state of the machine, machine service life or service life of parts, or even endanger
staff’s physical health.
4. During the operation and maintenance process of the machine, please be sure to avoid the
contact of ink and non-cleaning fluid, so as to prevent the ink from any chemical reaction
which may cause machine damage.
5. Since the waste fluid generated from the machine will pollute the environment, please
properly dispose of the waste fluid in accordance with the requirements of local
environmental protection department.
6. The auxiliary ink box, filter, ink pump, air pump, liquid pump, refill tube and print head of
the machine all belong to wearing parts and shall be replaced periodically as per the service
condition.

Safety precautions
To ensure that operators will properly use the equipment and prevent equipment damages and
unnecessary casualties, please carefully read the following safety precautions:
Please use the voltage as specified on the nameplate and never plug several devices into
one
power outlet at the same time to avoid fire disaster.
Please check and ensure the equipment has been grounded reliably. There is a grounding
identification at the bottom-left corner of the equipment. Otherwise, disturbance
may be caused and lead to abnormal image printing of the machine.
Never dismantle or transform the equipment by yourself, otherwise, such accidents as fire
disaster, electric shock and other accidents may be caused.
Keep the circuit control section of the equipment away from metal objects or liquid,
otherwise, it will cause circuit board damage, fire disaster or other accidents.
Never connect the power line of the equipment with wet hands, otherwise electric shock
may occur.
In the event of the following situations, please switch off the equipment and contact the
local dealer if necessary:
1. The switch is insensitive or doesn’t work.
2. When the inkjet printer makes abnormal sound or produces smoke.
3. When any metal object or liquid splashes into the electric control part of the
equipment.
4. When problems that operators fail to settle arise.

Operation precautions
Power supply
1. Inkjet printer shall be installed near the power source convenient to use and the
connecting outlet must be solid and reliable.
2. Relatively stable power supply in accordance with technical specification of
inkjet printer shall be used.
3. Connect the power line to a separate outlet and never share the same power
outlet with other equipment.
4. Pay attention to the order of power on and off so as to avoid damages to print
head.
5. In case of unstable local voltage, please use voltage stabilizer to guarantee the
stable voltage and choose the famous brand products, because inferior products
may cause equipment fault or damage electrical component of the equipment
(including print head).
Inkjet printer
1. Don’t place anything on the platform of the inkjet printer so as to avoid damages
to print head.
2. In case of any maintenance for the machine as regards electrical control, please
be sure to disconnect the power of inkjet printer. otherwise, personal injury or
machine damage may occur.
3. Never touch the surface of print head with hands or hard objects so as to prevent
damages to print head or printing quality reduction of print head.
Regular inspection and maintenance
1. Fill lithium base grease in mechanical parts with grease gun on a regular basis,
in circumstances of normal printing, fill in the ink carriage linear guide once for
every five shifts.
LIYU-PZR-KV-1-Series Manual www.liyu-dms.com - 10 -

2. See contents in Chapter 3 for maintenance method of ink and print head.

Contents
INTRODUCTION ............................................................................................................................. 2
TECHNICAL SPECIFICATIONS................................................................................................... 3
LIST OF MACHINE MODELS: ........................................................................................................... 3

LIST OF MAIN TECHNICAL
SPECIFICATIONS:..............................................................................................................................4
BASIC SPECIFICATION ................................................................................................................ 4
PRINTING EFFICIENCY LIST ....................................................................................................... 6
MACHINE OPTIONAL COMPONENTS .......................................................................................... 7
STANDARD ACCESSORIES .......................................................................................................... 8
IMPORTANT PARTICULARS ...................................................................................................... 9
SAFETY PRECAUTIONS ............................................................................................................. 10
OPERATION PRECAUTIONS ..................................................................................................... 11
CONTENTS ......................................................................................................................................13
CHAPTER 1: INTRODUCTION TO BASIC KNOWLEDGE .................................................. 15
WORKING CONDITIONS .............................................................................................................. 16

Working space ...................................................................................................................... 16
Environmental requirements ............................................................................................... 16
Computer configuration requirements ...................................................................... 17
MACHINE UNPACKING AND FLOOR INSTALLATION ............................................................17
APPEARANCE, NAME AND FUNCTIONS OF PARTS ........................................................................ 21
Carriage view ........................................................................................................................ 24
Auxiliary ink tank view ......................................................................................................... 26
Accessories figure ................................................................................................................. 28
Moisturizing tray .................................................................................................................. 28
Roll paper tray ...................................................................................................................... 28
Liquid Receiver Tank ........................................................................................................... 29
Waste liquor bottle .......................................................................................................30
CONSUMABLES .......................................................................................................................... 31
Printing media .......................................................................................................................31
Ink and cleaning fluid .......................................................................................................... 31
Maintenance tools ............................................................................................................... 32
CHAPTER 2: BASIC OPERATION .............................................................................................33
MACHINE INSTALLATION ................................................................................................34

SWITCH ON AND OFF .................................................................................................................35
Switch on .................................................................................................................................35
Switch off .................................................................................................................................36
COMPUTER CONNECTION ................................................................................................37
INSTALLATION AND ADJUSTMENT OF PRINT HEAD ..............................................................39
Print head description ....................................................................................................... 39
Print head installation .......................................................................................................40
Electrical connection ..................................................................................................... 43
Machine with 4 print heads ........................................................................................ 44

Machine with 8 print heads ........................................................................................ 44

Adjustment of print head .............................................................................................46
INSTALLATION OF PRINTING MEDIA ........................................................................................... 47
Single roller take-up and feeding system.............................................................................. 47
Double-roller feeding system ......................................................................................48
FUNCTIONS OF KEYS AND BUTTONS .......................................................................................... 48
Left button panel ................................................................................................................... 49
Right button panel ................................................................................................................ 49
Suction section switch panel ................................................................................................. 50
Button panel behind the right box ........................................................................................ 51
Infra-red heating unit ........................................................................................................... 52
Button panel behind the left box .......................................................................................... 52
Switch of single and double-roller feeding system .................................................... 53
ADD INK AND FILL THE PRINT HEAD WITH INK ........................................................................... 53
Install ink and cleaning fluid ............................................................................................... 54
Inject ink into the auxiliary ink tank .................................................................................... 54
Inject ink into the print head ......................................................................................54
POSITIVE PRESSURE INK ......................................................................................................56
NEGATIVE PRESSURE ADJUSTMENT ................................................................................... 56
Vacuum Negative Pressure Adjustment ................................................................... 56
CHAPTER 3 MAINTENANCE AND SERVICE ........................................................................ 59
DAILY MAINTENANCE INSTRUCTIONS .................................................................................... 60

PRINT HEAD MAINTENANCE INSTRUCTIONS .............................................................................. 60
INK USE GUIDELINES .......................................................................................................... 62
APPENDIX I: DETAILED SETTING OF VACUUM PRESSURE GAUGE .......................... 63
AppendixⅠDetailed setting of vacuum pressure gauge………………….……………54

Chapter 1: Introduction to Basic

Knowledge
This chapter dwells on the necessary information for inkjet printer operation. Please understand
the necessary information before reading other chapters.
Contents of this chapter:
Working conditions
Working space
Environmental requirements
Computer configuration requirements
Machine unpacking and floor installation
Appearance, name and functions of parts
Front view
Back view
Accessories figure
Consumables

Working conditions
Working space
There must be enough space surrounding the inkjet printer so as to facilitate replacement of some
commonly used spare parts and printing media, drawings output and ventilation. In addition,
make room for maintenance (as shown below) with the aim of printer repair or spare parts
replacement.
Installation and maintenance space is shown in the following figure:
1000mm
500mm 500mm
(Front side)
1000mm
Environmental requirements
Operation temperature and humidity:
The optimal working temperature and humidity of the equipment: temperature 150C - 280C,
humidity 40%~80%.
Please try to keep the equipment working under the optimal working temperature and humidity;
otherwise, the printing quality may drop.
Don’t install the machine at the following locations:

In direct sunlight
Location with vibration
Dusty places
Location with drastic temperature variation
Location with great air mobility
Near the air-conditioning or heater
Place likely to be wetted
Place likely to produce other polluting gas
Unstable location
Computer configuration requirements
The minimum configuration requirements for the software operation of the product are as
follows:
CPU: CPU of dual core above 2.0G.
Mother board: High quality brand mother board, with USB2.0 interface.
Display card: Graphic display card with video memory above 256M.
Memory: Memory above 2G.
Other: CD—ROM drive.

Hard disk: Over 40 G room is left, please use NTFS format as the hard disk format.
Operating system: WINDOWS XP, WIN7
Machine unpacking and floor installation
1. Cut the steel strips on the packing box, four in total. The location of steel strips in red mark
is shown in the following figure:

2. Remove the fastening screws of the packing box in turn, 30 in total, take down the side plate
and top cap of the packing box. The location of screws in red mark is shown in the following
figure:
3. Remove the connecting bolts of the packing pressing plate in turn, 4 places in total, take
down the packing pressing plate. The location of packing pressing plate in red mark is
shown in the following figure:

4. Use the forklift above 1.5T to fork the machine to the ground, with the forklift placed in the
middle of the machine to ensure stability. When the machine smoothly lands on the ground,
push the machine in place (pay attention to safety operation while forking the machine).
the forklift is placed as shown in the following figure:
5. Screw out the supporting feet at the corners of the rack (4 places) and make its swivel casters
(8) hang in the air. Screw in other supporting feet and make swivel casters far away from
the ground. as shown in the following figure:

6. Adopt level gauge with sensitivity above 0.05mm/m and place the level gauge in the middle
of printing platform by adjusting the supporting feet of four corners of the rack, and regulate
the level to make the level precision within 0.1mm/m. (Note: ①. During the adjustment
process, the swivel casters shall never touch the ground. ②. If double-roller feeding system
is used together with the level gauge, adjust the left and right supports of double-roller
feeding system to make the level precision of double-roller within 0.1mm/m).
7. Complete.

Appearance, name and functions of parts
Front view
1: Upper Left Box Generally speaking, the carriage stops inside the upper left
box when it is idle.
2: Left Button Panel The button panel includes such buttons as power on,
positive pressure and cleaning.
3: Guide Cover Dust proof, provide protection for carriage parts.
4: Printing Platform The printing platform has such functions as platform

heating and subsection vacuum suction underneath.
5: Guide Beam The cross beam and guide of the machine are the important
components for ensuring smooth running of the carriage.
6: Front Panel Front panel has the function of heating, mainly used for
drying the image printed, enabling the ink take shape on
the media.
7: Right Button Panel The button panel includes regulating switch of platform

absorption fan, electric roller lift switch and print head

high voltage switch etc.
8: Upper Right Box It is used for installation of computer monitor and servo
motor drive etc.
9: Lower Right Box Lower right box mainly contains weak current circuit,
ink supply system, main control circuit board and
computer host etc.
10: Adjusting Seat When installing the machine, make the adjusting seat
touch the ground reliably so as to stabilize the inkjet
printer.
11: Tension Shaft During automatic take-up and feeding process, always
provide stable tension for the media, meanwhile, trigger
the mechanical switch to control the work of take-up
motor through the front-to-back motion of tension shaft.
12: Infra-red Heating Unit Infra-red heating unit contains infrared heating tube and
fan, mainly used for further drying of images printed.
13: Lower Left Box Lower left box mainly contains strong current circuit,
including feeding motor, switching power supply,
various filters, relay and contactor etc.
14: Caster It is used to push the inkjet printer.
. LIYU-PZR-KV-1-Series Handbuch www.liyu-dms.com - 21 -

Back view
1: Right Rear Button Panel The control button and roller lift/fall button of take-up and
feeding system are on the button panel.
2: Feeding Optoelectronic Reflective optoelectronic switch is used for media detection

Switch so as to control the operation of feeding motor.
3: Machine Cover Dust proof. Provide protection for cross beam parts.
4: Back Panel The back panel is equipped with heating unit and used for
preheating of media, so as to achieve better printing effects.
5: Peeling Shaft It is used to peel the sticky entire volume of media not
printed yet.
6: Feeding Shaft It is used to support the entire volume of media not printed
yet.
7: Left Rear Button Panel It is used to control the temperature of infra-red heating
unit, front panel, platform and back panel.
8: Power Input Power interface of heating system and machine power

input port.
9: Take-up Motor Drive the take-up shaft to rotate and complete automatic
take-up process of media printed.
LIYU-PZR-KV-1-Series Handbuch www.liyu-dms.com - 22 -

10: Take-up Shaft Automatic take-up of the media completing printing.
Carriage view
1: Environment Plate Protect carriage plate, auxiliary ink tank, air tube and ink tube etc.
Cover
2: Cover Plate Protect auxiliary ink tank, air tube and ink tube etc.
3: Carriage Cover Protect the print head.

4: Three-way Valve Three-way valve is used to control cleaning fluid or ink into the print
head and has three states: namely close, connected with ink path and
connected with cleaning fluid.
5: Two-way Valve Core Every valve core corresponds to one ink outlet of print head. The valve
core has two states: open and close. mainly used for ink filling of the
print head for the first time and print head venting.
Three-way valve:
Three states for every three-way valve are shown in the following figure:

State 1: Working sta

te State 2: Cleaningstate State 3: Off state Interface of cleaning fluid
State 1: Working state, when the equipment is in normal operation, especially in
printing, the valve shall be in this state.
State 2: Cleaning state, when it’s time to clean the print head with cleaning fluid,
please places the valve in this state.
State 3: Off state, when the equipment is shut down, place the valve in close state.
Print head height adjusting handle
Note: In the above figure, the rotation direction marked in Picture 1 is the rotation
direction of fastening the adjustment rod. Please tighten the lock screw
according to the direction at any time except when you adjust the print head
height.

The rotation direction marked in Picture 2 is the rotation direction of loosening
the adjustment rod.
The rotation direction marked in Picture 3 is the rotation direction of raising the
print head height.
The rotation direction marked in Picture 4 is the rotation direction of reducing the
print head height.
When you need to adjust the print head height, please follow the steps below:
a. Rotate the lock screw as per the rotation direction in Picture 2 and loosen the
adjustment rod.
b. Rotate the adjusting handle as per Picture 3 and Picture 4 (when you raise the print
head height, rotate the handle as per Picture 3. if you reduce the print head height,
rotate the handle as per Picture 4.) and adjust the print head to the proper height.
c. Fasten the adjustment rod as per the rotation direction in Picture 1 and complete the
adjustment of print head height.
Two-way valve core:
Every two-way valve has two taps and two valve cores and is
connected with the ink nozzle of two different print heads through
ink tube. In the state of pressing ink to the print head, use a flat
head screwdriver. The flat head gap in vertical state
stands for open state, then ink and bubble will flow to the
two-way valve through ink nozzle of the print head and
discharge from the ink outlet beneath. the flat head gap in
horizontal state stands for close state and blocks the ink inlet
of two-way valve.

Auxiliary ink tank view
1: Air Tube From safety bottle to auxiliary ink tank.

2: Waste Liquid Tank Safety bottle has two functions, one of which is the air
(Safety Bottle) channel. the other is to send out alarm and stop all the ink
pump work in case that the ink level in the waster liquid tank
reaches a certain height after ink inverse suction, so as to
prevent ink from flowing directly to the electromagnetic
valve of control air channel.
3: Ink Discharge Tube The outlet of waster ink in waste liquid tank (safety bottle).
4: Cleaning Fluid Tube
When you press the cleaning button, cleaning fluid will flow
into the print head from the tube.
5: Liquid Level Sensor Lead It is connected to the carriage plate, detecting the liquid level
Wire in auxiliary ink tank.。
6: Ink Inlet Tube It is connected to the ink inlet of auxiliary ink tank on one
end, and the other end is connected to the ink outlet of ink
pump.

7: Auxiliary Ink Tank Secondary ink box of ink supply system.
8: Ink Tube From auxiliary ink tank to three-way valve.
9: Measuring Sensor It is used to detect the position and width of materials.
Accessories figure
Moisturizing tray Roll paper tray
USB cable Flat cable of print head
Moisturizing tray
Moisturizing tray is used for print head moisturizing. When the print head is
moisturized, place one to two layers of non-woven fabrics on the moisturizing tray and
inject proper amount of cleaning fluid (make sure that the non-woven fabrics on the
moisturizing tray are drenched), then put the moisturizing tray on the print head plate
and tighten the screw, ensuring the sound contact of nozzle surface and cleaning fluid.
Roll paper tray
It is used for fixing the whole volume of printing materials through tightening star
screw.

Single roller feeding system is equipped with four roll paper trays and double-roller
feeding system is equipped with two trays.
Liquid Receiver Tank
Liquid receiver tank is installed in the upper left case, with corresponding pipelines
connected, used to recover waste liquid generated from pressing ink, cleaning and flash
spray. To ensure transportation safety, liquid receiver tank is fixed with screws. Please
remove the screws (two screws marked with red circle) before use, as shown in the
following figure:
Liquid receiver tank can be pushed back and forth after removing the above two screws
and be placed right under the print head during working state, so as to facilitate waste
fluid recovery while pressing ink, cleaning and flash spray. If you need to wipe the
nozzle surface after pressing ink and cleaning, you can push the liquid receiver tank to
the back, as shown in the following figure, and pull it back to the original position after
wiping the print head.

Waste liquor bottle
During machine installation, install the waste ink bottle in the lower left case of the
machine and connect the corresponding pipelines, then open the valve (the specific
position is shown in the following figure). Make sure that the waste ink bottle is always
installed on the machine except when you move the machine or pour out the waste ink.
Please close the valve before taking out the waste ink bottle.
Note Valve state (see above left):
1 valve is close 2 valve is open.

Consumables
Printing media
The common media for the inkjet printer include such commonly used media for advertising
equipment as light box cloth and body paste. Please pay attention to the following matters
as regards media purchase, storage, use and disposal:
Inferior medium may reduce the printing quality, so it is suggested you select the high
quality printing media.
Do not store the media vertically so as to avoid clutter or damaged edge, and the media
are not suitable for stack placement either.
Do not preserve the media in the environment with great temperature and humidity
changes, instead, the media shall be preserved in clean and tidy environment with
proper temperature and humidity.
Do not use the printing media with scratch, wrinkle, curl and surface bulge. If you use
this kind of printing media, paper feeding (printing media) on both sides of the roller
will be affected, which may even result in equipment failure or damage in severe case.
Ensure the clean and tidy printing surface of the media during printing, free from any
dust and clutter, otherwise, equipment failure or damage may occur.
Ink and cleaning fluid
The print head of inkjet printer belongs to high precision equipment. therefore, the ink
quality will greatly affect the printing quality and the service life of print head. Please use
the ink and cleaning fluid recommended by the manufacturer and pay attention to the
following items at the same time:
Failure to use the ink as recommended may cause lowered printing quality or
equipment
damage.
The guarantee period of ink is six months in general (calculated from the production
date), so please use the ink within guarantee period.
Make sure that there is plenty of ink in main ink bottle during the working period of
the machine.

Ink should be kept in a shady and cool place.
Since ink and cleaning fluid are strong acid or alkaline liquid, please store them
properly and try to avoid skin contact, let alone swallow, and keep it away from eyes.
Maintenance tools
Please use the cleaning fluid recommended by the manufacturer to clean the print head,
moreover, use the specialized wiping paper recommended by the manufacturer to wipe the
print head, otherwise, it may lead to the permanent damage to the print head.

Chapter 2: Basic Operation
This chapter illustrates such basic movement as machine installation and operation.
Main contents in this chapter:
Machine installation
Switch on and off
Computer connection
Installation and adjustment of print head
Installation of printing media
Functions of keys and buttons
Add ink and fill the print head with ink
Positive pressure ink
Negative pressure adjustment

Machine installation
1. Please purchase a computer as per computer configuration requirements and install the
necessary software (windows xp operation system, graphic and image processing software,
RIP software, please refer to the software operating instructions or consult after-sales
department of our company regarding the installation of various software).
2. Please carefully check whether the packing list is consistent with articles in the box or the
machine is intact after opening the box. Please contact our company or the local dealer in
time if you have any question.
3. Place the machine according to machine placing requirements and regulate the adjusting
seat of machine, ensuring the sound contact of the adjusting seat of machine and the ground,
stable without shaking.
4. Connect the computer: the machine adopts USB port to connect with the computer,
meanwhile, to ensure the reliability of communication, USB port of the machine is not
extended to the outside of the machine, instead, you have to connect USB port directly to
the motherboard. Please refer to LiyuPrint help file or LiyuPrint operation manual for drive
installation.
5. Connect the ground wire of the machine, with the ground resistance of the ground wire less
than 100 Ohm. Copper core of 4mm2 is recommended, at the same time, ensure the reliable
connection between the ground terminal and the ground.
6. Place the take-up and feeding system, various shafts and roll paper tray according to the
machine view.

Switch on and off
Switch on
1. The machine adopts an AC 220V 50HZ power supply. The specifications and
connection method are described as follows, please be sure to connect them pursuant
to descriptions and specifications. AC 11OV 60HZ power supply needs the
transformer, and our company can equip users with transformer according to
requirements of orders (Please properly connect the transformer equipped along with
the machine as per the instructions of the transformer).
Illustration: In the above picture, 1 refers to the power interface of heating system,
with the power specification of AC220V >16A. 2 refers to the power
interface of the machine, with the power specification of AC220V <10A.

Please select the appropriate power supply, otherwise, it may cause

abnormal conditions and even danger.
2. Put the air switch in control of the machine power in lower left box to the position of
“ON”.
3. Switch on the left and right “EMERGENCY STOP” buttons.
4. Press “POWER” button of the machine (both left button panel and right button panel
have “POWER” button).
5. Then the machine will inspect itself.
6. The carriage will stop at the cleaning position on the left after the machine completes
self-inspection. Now it’s power on.
7. Then you can turn on high voltage, please make sure that you have pressed high voltage
button before printing every time.
Note: Please make sure that you switch on the machine before turning on high voltage of print head.
Switch off
1. Make sure that the print head of the machine is not working.
2. Turn off high voltage of the print head of the machine.
3. Press “EMERGENCY STOP” button of the machine.
4. Put the air switch in control of the machine power in lower left box to the position of
“OFF”.
Note: Please make sure that you turn off high voltage of print head before switching off the machine
power, except in emergency.

Computer connection
1. Connect USB cable reserved on the machine to USB port of computer and start the machine.
If drive is not installed in the computer, users will be prompted to install the drive program.
2. Select “install from the list or designated location” and click next, then you are required to
select drive storage path (suppose the drive storage path is
c:\LiYuPrint_UV\LiYuPrintDriver\LiYuDriver_USB)
3. Click browse and select drive storage directory, click confirm and then next.

4. It starts to install drive program. There may be a prompt window, just click “Continue
Anyway” and the installation will continue.
5. The first phase of installation is completed.

6. After completing the first phase of installation, once again there will be a prompt of finding
new software from the system. Just repeat step1 to step 4 to complete the full installation.
7. After completing the full installation, open the device manager of the system. If you can
find the newly-installed USB device---U_V_USB Transfer Device, it shows the successful
installation.
Installation and adjustment of print head
Some print heads of the machine have not been installed onto the machine. therefore, this
chapter will start from the installation of single print head to the machine. If print heads have
been installed onto the machine, please omit the illustration of print head installation.
Print head description
The machine uses KM512iLNB type print head. Please check whether the model on print
head packing is consistent with the model applied by the machine before unpacking.
The identification and description on the print head packing are as follows:

Print head identification: KM512iLNB-30
30:30pl
N: Without built-in heating of print head (solvent-based print head is
N type print head)
H: With built-in heating of print head (UV type is H type print head).
001957: Print head number
L: 12.6V and R: 12.6V respectively mark the reference voltage of the

left and right row of nozzle.
Print head installation
1. First install the bottom plate of print head onto the machine and place clean non-woven
fabrics under the bottom plate of print head, so as to avoid soiling nozzle panel or
blocking nozzle during print head installation process.
2. Remove the packing of print head according to the order below and take down the
protection cover under print head (the protection cover is used to protect nozzle panel):

3. Place the print head on the bottom plate of printing head as shown in the following
installation diagram.
4. Fix the print head with fastening screw and adjusting screw as shown in the following
figure.
Note: Screw, spring washer and flat washer marked as 1 in the above figure are used
to fix the print head with the specification of M4x16. screw marked as 2 are
used to adjust deflection and front and rear position of the print head.

5. Install all the print heads onto the bottom plate of printing head according to the above
four steps and tighten all the fastening screw and adjusting screw.
6. After installing all the print heads as per the above method, you will install the ink path
of the print head. There are two positions on the print head for connecting with ink tube,
namely ink inlet 2 and ink outlet 1, as shown in the following figure:
Before leaving the factory, the machine has been equipped with ink tubes as needed, as shown in the
following figure:
Valve
body
This is the eight-print machine. The quantity

ink tubes allocated of for machines of other
models may vary.

Note: The mark with H in the above picture is the number of installation position of print head.
The mark with O is the number of ink outlet tube of print head while the mark with I is
the number of ink inlet tube of print head.
During print head installation and ink tube connection, just connect one-to-one
according to the tail number of the mark. For the machine with four print heads, the tail
number of print head installation position mark is odd number. The mark with even
number is not used. You can only remove the black plug right before connecting ink
tube, so as to prevent dust from falling into ink tube.
Electrical connection
1. Installation position and the corresponding colors for print head and driver board of print
head.

Machine with 4 print heads
When high speed machine is equipped with four print heads, the corresponding
relation between print head connection wire and print head on the carriage plate
is shown in the following figure:
Machine with 8 print heads
When high speed machine is equipped with eight print heads, the corresponding relation
between print head connection wire and print head on the carriage plate is shown in the
following figure:

2. The electrical connection of print head is relatively simple. Just connect the driver board of
print head to print head connection wire with 50PIN connection cable attached. Pay attention
to the interface direction during connection.
As shown in the following figure:

Adjustment of print head
To guarantee printing quality, carry out necessary adjustment of the physical location of the
print head before printing image, with the purpose of ensuring verticality between all nozzle
lines and printing direction and that nozzles in the same row are in the same horizontal line
and the last nozzle in the first row has a spacing (of 25.4mm/physical resolution of print
head) with the first nozzle in the second row.
Adjustment of print head mainly refers to adjustment of the physical position of print head
installation with adjusting screw, as shown in the following figure:
Note 1: Adjusting screw 1 is mainly used to adjust the front and rear position of print head,
and adjusting screw 2 is mainly used to adjust the vertical position of print head.
The steps of physical adjustment of print head are as follows:
1. Print head arrangement inspection, observe the adjustment requirements of the print
head in view of the test pattern and adjust the print head number 0 to the best position.
Please refer to LiyuPrint help file or LiyuPrint operation manual for detailed
description of calibration test pattern and calibration order of print head.
2. Printing tilt inspection 1，observe the adjustment requirements of the print head in
view of the test pattern and adjust all the print heads number 0 to the best position.
Please refer to LiyuPrint help file or LiyuPrint operation manual for detailed description
of calibration test pattern and calibration order of print head.
3. Print head arrangement inspection, observe the adjustment requirements of the print
head in view of the test pattern and adjust all the print heads number 1 to the best
position.
4. Printing tilt inspection 1, observe the adjustment requirements of the print head in view
of the test pattern and adjust all the print heads number 1 to the best position.

5. Tighten the fastening screw of print head and print the test pattern for verifying effects
again. If it turns out to be undesirable, return to the first step and continue to adjust,
until you get the satisfactory effects.
Installation of printing media
Single roller take-up and feeding system

Double-roller feeding system
Note: Both single roller and double-roller feeding system can be configured as automatic take-
up device. The above example only stands for two common configuration and our
company can flexibly configure the take-up and feeding system according to customers’
needs.

Functions of keys and buttons
1.Power button 2.Positive pressure button 3.Purge button 4.Emergency stop button
Left button panel
(1) Power button The button is used to start inkjet printer. Switch on the
power of inkjet printer and turn on the air switch in
strong current control cabinet, ensuring the emergency
stop button is in bouncing state, then press the button
to start the device.
(2) Positive pressure The button is used to start positive pressure system. Put
button positive pressure on ink route system to enable ink to
flow out from the valve body or nozzle, achieving the
effect of venting for ink route of print head or cleaning
print head. (This operation shall be completed with the
operation of valve body)
(3) Purge button The button is used to start cleaning fluid pump, which
pumps the cleaning fluid to the carriage from the
container so as to clean the print head. (This operation
shall be completed with the operation of valve body)
(4) Emergency stop button In emergency circumstances, press the button and the
inkjet printer will stop running.

Right button panel
1:Vacuum Pressure Gauge (Negative It is used to display, set and inspect the vacuum pressure
Pressure Meter) in auxiliary ink box.
2: Emergency Stop In emergency circumstances, press the button and the
inkjet printer will stop running.
3:Vacuum Adjustment Button On/Off, and adjust the vacuum of the platform.
4:Pinch Roller Up/Down Button It is used to lift or lower the pinch roller. When the
pinch roller is up, press the button and the pinch roller
will fall automatically. When the pinch roller is down,
press the button and the pinch roller will rise.
5:High Voltage Switch of Print Head Switch on or switch off high voltage of print head.
6: Power button The button is used to start inkjet printer. Switch on the
power of inkjet printer and turn on the air switch in
strong current control cabinet, ensuring the emergency
stop button is in bouncing state, then press the button
to start the device.

Suction section switch panel
Suction Switch SW1
Suction Switch SW2
Suction Switch SW3
Suction Switch SW1 Switch the suction fan on or off from 0 to 1.8m section on the machine
platform (from the right end of the platform).
Suction Switch SW2 Switch the suction fan on or off from 1.8 to 2.5m section on the machine
Suction Switch SW3 Switch the suction fan on or off from 2.5 to 3.2m section on the machine

Button panel behind the right box
1:Manual/Automatic Press the button for manual feeding state. The button
Feeding needs to be used in concert with the second or third
button.
The feeding motor can be started only after pressing

2: Feeding Forward
the button and work after triggering feeding
conditions.
The rotation direction of feeding motor is contrary to

3: Feeding Reverse the original direction after pressing the button.
4: Take-up When the button bounces up, take up automatically in

Forward/Reverse coordination with take-up sensor. Press the button
and release the materials of cloth shaft. If you want to
suspend or stop automatic take-up during take-up
process, just push the tensioning shaft to the highest
position.
It is used for lift or lower the pinch roller. When the

5: Pinch Roller
pinch roller is up, press the button and the pinch roller
Up/Down will fall automatically. When the pinch roller is down,
press the button and the pinch roller will rise.

Infra-red heating unit
1 Switch the fans on or off from 0 to 1.8m section of infra-red heating unit (from the right end of
the infra-red heating unit).
2 Switch the fans on or off from 1.8 to 2.5m section of infra-red heating unit (from the right end
of the infra-red heating unit).
3 Switch the fans on or off from 2.5 to 3.2m section of infra-red heating unit (from the right end
of the infra-red heating unit).
4 Switch the infra-red heating tube on or off from 0 to 1.8m section of infra-red heating tube in
infra-red heating unit (from the right end of the infra-red heating unit) (button at the bottom).
5 Switch the infra-red heating tube on or off from 1.8 to 2.5m section of infra-red heating tube
in infra-red heating unit (from the right end of the infra-red heating unit) (button at the bottom).
6 Switch the infra-red heating tube on or off from 2.5 to 3.2m section of infra-red heating tube
in infra-red heating unit (from the right end of the infra-red heating unit) (button at the bottom).
Button panel behind the left box
. LIYU-PZR-KV-1-Series Manual www.liyu-dms.com - 52 -

1: Infrared Heater Switch on infra-red tube and temperature controller. The

temperature of factory setting is 50℃. Press “set” button,
then the number after decimal point glitters, adjust it by
pressing “∧ ”and “∨ ”. press “set” button for the second time,
the number right before decimal point glitters, adjust it by
pressing “∧ ”and “∨ ”. press “set” button for the third time,
the second number before decimal point
glitters, adjust it by pressing “∧ ”and “∨ ”.customers adjust
the temperature according to actual conditions.
Turn on the rocker switch on the right side and adjust the
2: Front Media
Heater temperature in the same way as 1, with the temperature of
factory setting at 40℃. Customers adjust the temperature
according to actual conditions.
3：Bed Media Turn on the rocker switch on the right side and adjust the
4: Rear Media Turn on the rocker switch on the right side and adjust the
Switch of single and double-roller feeding system
The button
controls single
or double-roller
feeding
Notes: the switch of single and double-roller feeding system is installed in the lower left box of the
machine. only the machine with single and double-roller feeding functions has this button.

Add ink and fill the print head with ink
Install ink and cleaning fluid
Directly place the cleaning fluid bottle and ink bottle with enough ink in the lower right
box of the machine according to the color order marked on filters (placement is shown in
the following figure), and insert the ink tube of corresponding color into the ink bottle.
Note: In the following figure, K, C, M and Y stand for corresonding four colors of ink, and F
is the cleaning agent.
Inject ink into the auxiliary ink tank
Please make sure that there is enough ink in the main ink bottle before injecting ink into the auxiliary
ink tank and the steps are as follows:
Ensure that there is enough ink in the main ink bottle and conduct inspection of the machine
before starting.
Start the inkjet printer. You can either reset the machine or not reset the machine by pressing
motor power button and cutting off motor power line.
After the inkjet printer starts, ink pumps of various colors will set to work and pump ink
from the main ink bottle to the auxiliary ink tank.
When all the ink pumps stop working, it means all the auxiliary ink tanks have been injected
with ink.
The transient buzzer sound during the process may be resulted from rather long ink pump
route and timeout.

In the event of ink pump not working or prolonged alarming of buzzer, please switch off
the machine in time and examine. In case of failure to settle the problem, please contact the
local dealer or after-sales department of our company immediately.
Inject ink into the print head
Since it is a very important operation to inject ink into the print head, please operate in
strict accordance with requirements. There are two critical operations, namely print head
cleaning and venting.
Print head cleaning:
The new print head must be purged with cleaning fluid before being injected with ink
for the first time because protective liquid has been injected into the nozzle of print
head. You must wash off the protective liquid before injecting ink. Otherwise, the
printing quality of print head will decline. Cleaning method of new print head:
a Properly connect all the wires of the machine (including print head wire), start
the machine and press high voltage button of the print head.
b In view of the power of cleaning fluid pump, it is suggested that you clean a
single print head every time. First, put the three-way valve of single print head
at purging state with other print head valves off, then unscrew corresponding
two-way valve, press purging button and make the cleaning fluid flow out from
two-way valve, clean the pipelines of this part. About one or two seconds later,
tighten two-way valve and make the cleaning fluid cascade out from nozzle for
about five seconds. clean other print heads according to the above method. c
Five minutes later, clean all the print heads again as per the above method.
d Wait for five minutes and clean them once again.
Venting of print head:
Inject ink into the print head after cleaning print head. Venting operation shall be conducted
together with ink injection with the specific operation process as follows:
1. It is also suggested that you conduct venting for every single print head, that is
to say, venting operation is conducted for only one print head every time with
valve body of other print heads off.
2. First of all, put the corresponding three-way valve in working state.
3. Unscrew the corresponding two-way valve core to ensure smooth ink outlet.
Press positive pressure button and impress ink from the auxiliary ink tank into
the print head, then ink will flow out from two-way valve core. Observe the ink
tube of ink outlet until there is no bubble in the ink tube, then tighten two-way
valve and make ink flow out from the nozzle. (Tips: it may takes long to impress
ink for the first time with such long pipelines, moreover, there is no sufficient
ink in the auxiliary ink tank, please hold on for a while after positive pressure so
as to enable ink supply system to refill the auxiliary ink tank and then continue
positive pressure).
4. Carry out the above operation for every print head in succession. Place all three-
way valves in working state after completing venting for all print heads. Press
positive pressure button and impress ink for all print heads again, then complete
ink injection of print heads.
5. Meanwhile, in case of bubble found in ink tube leading to print head, which
affects ink out of the print head, the above method can also be adopted to carry
out venting operation.
Positive pressure ink
Positive pressure ink refers to impressing ink of the auxiliary ink tank into the print head by
pressing positive pressure button to eliminate the air in the nozzle and flush through the nozzle
blocked not so seriously, as well as solve some common problems of printing disconnection.
You can impose positive pressure to either a single print head or several or all print heads with the
specific operation steps as follows:
Stop the ink carriage at the cleaning position, namely the far left of the machine, and ensure
that the liquid receiver tank has been put in place under the bottom plate of print head.
Turn the three-way valve of the print head demanding ink to working state, with other valves
off.
Press positive pressure button and hold for a while, observe the ink out status of print head
and release positive pressure button when you feel ink flowing smoothly.
Wait for two seconds and wipe the nozzle surface with clean non-woven fabrics.
Negative Pressure Adjustment
Since negative pressure is an important factor for guarantying print quality, the operation of its
adjustment is crucial. The target of adjustment is to make ink form meniscus in every nozzle
printer. As long as sound meniscus is maintained, we can assure that ink droplets are ejected at
a high speed with few flight drops. Vacuum negative pressure system is applied to this printer.
The adjustment of negative pressure is as follows.
Vacuum Negative Pressure Adjustment
The intensity of vacuum negative pressure can be adjusted by the vacuum pressure gauge.
Panasonic DP - 101 vacuum pressure gauge is selected to control negative pressure for this
printer. The vacuum pressure gauge is operated on the right button panel. The following picture
demonstrates the negative pressure system.
For detail settings, please refer to appendix 1.

Mark Name Function

Number
1 Vacuum pressure system To provide steady negative pressure for print

head in accordance with the settings of the
vacuum pressure gauge.
2 Positive Pressure gauge To maintain pressure within the setting range

when ink is pressed with positive pressure.
1. Calculation of the setting value of negative pressure gauge:
In total, two values are required to be set on the negative pressure gauge, namely,
P_1,P_2，whose unit is Kpa. Among them, p_2 = P_1 - 0.2 . For instance, P_1is set
to be -1.6；-1.6 - 0.2= -1.8；the setting value of p_2 should be -1.8 and the final
negative pressure value lies between P_1 and p_2.
2. Operation to change the setting values of negative pressure gauge:
a: Press “MODE” button to enter the setting state-the minor screen will show Lo_1
for one time-then the value of Lo_1will be displayed- adjust its value through ▲or
▼button.
Press ”MODE” button again to enter the setting state of Hi_1- the minor screen will
show Hi_1 for one time and then shown its value, - adjust the value by pressing ▲or▼
button.
Press ”MODE” again to enter the setting state of P_2- the minor screen will show P_2
for one time - showing its value- adjust by pressing ▲or▼ button.
b: Press “MODE” button to enter the setting state, and the minor screen will show P_1
for one time-and then will show its value-adjust its value through ▲or ▼button.
Press ”MODE” again to enter the setting state of P_2, and the minor screen will shows
P_2 for one time and then show its value– adjust its value by pressing ▲or▼ button.

Caution: When adjusting the setting values of the pressure gauge, the interval between your
settings should not exceed 0.2 at best.
Operation is set as an example as follows to demonstrate the setting process.
The vacuum pressure gauge shows

normal negative pressure
Press “MODE” button
The Pressure gauge shows Lo_1 and

its current setting value. Adjust its
value into the one calculated
following the above -said method by
using the up/ down arrow.
The Pressure gauge shows Hi_1 and

its current setting value. Adjust its
value into the calculated one.
The Pressure gauge shows P_2 and its

current setting value. Adjust its value
into the calculated one.
Setting completed

Chapter 3 Maintenance and Service
Contents of this chapter:
Daily maintenance instructions
Print head maintenance instructions
Ink use guidelines

Daily Maintenance Instructions
1. Keep the working environment of the printer clean and ventilated, and clean dust and
ink on the printer periodically.
2. Keep the work surface clean. Every time before starting it up, check whether the
working board is cleaned, to avoid scatching the print head.
3. Inject lithium base greases into the slider by grease gun every forty hours operation, to
reduce its frictional resistance against the guide rail and extend its service life.
4. Maintain an appropriate belt tightening of the ink carriage timing belt, which can be
adjusted after removing the upper left end cap. After the adjustment, connecting screws
must be fixed tightly.
5. Every time after finishing refilling ink, make sure the cover of the main ink tank is
screwed tightly. Wipe off residual ink on the tank.
6. For positive pressure printing, after wiping the printhead, flash spray for around 20
seconds first before printing pictures, to achieve sound meniscus formed by ink droplets
in the nozzle.
7. During the interval of printing pictures, printer please keep the print head under the
state of flash spray, in order to guarantee a smooth nozzle.
8. The area around the orifice must be maintained clean,. No residual ink, dust or fiber is
allowed. Orifice shall not be scratched.
9. Since the ink and the cleaning fluid contain strong solvent, they mustn’t contact
electrical components and wires. Were ink or cleaning fluid spilled on them accidently,
they would be wiped off cleanly as soon as possible.
10. Clear liquid waste in the liquid waste box in time.
11. When the suck-back phenomenon occurs to the printer and ink appears in the air tube
of the minor ink cartridge, the printer should be stopped immediately to discharge the
ink from the air tube and the waste liquid tank (safety bottle) and replace the air tube
with a new one.
12. Every day before the startup and shutdown, it is recommended to print nozzle test chart
to check whether the nozzle is in normal condition. Provided that ink outflows brokenly,
press the ink or clean the nozzle to make it work properly.
Print head Maintenance Instructions
As the core component, the print head is much expensive and sensitive, which requires good
maintenance. Otherwise, print quality and its service life would be seriously affected. Print head
maintenance instructions are as follows:

1. In using the printer, please use the ink appointed by the manufacturer or authenticated
by KONICA. Do not change the ink at will, or it might lead to malfunction of print head.
2. When the device stops running, maintenance methods of different sorts should be
adopted in accordance with the length of downtime:
If printer downtime is within a working day and you are not willing to turn it off, it
should be set under the state of flash spray. Before the flash work, please confirm the
status of print head. If it is not in a good condition, do the ink press operation first.
If the downtime is over 12 hours to a whole day, it is recommended that the valve
knob be screwed to the closed state, the ink carriage be stopped within the upper left
case, power be switched off, a layer of non-woven fabrics be embedded into the wet
protection tray, a small amount of cleaning liquid be injected into the wet protection
tray (non-woven fabrics should be drenched), and then the print head can be
moisturized with the wet protection tray, during which operation make sure that the
whole nozzle surface is in touch with cleaning liquid.
If the downtime is within two days, the maintenance operations are the same as the
previous one. Meanwhile, non-woven fabrics in the wet protection tray should be
replaced every day, and new cleaning liquid should be injected into it (Cleaning liquid
needs to be changed, because components of moisturizing function within it are easy
to volatilize).
If the downtime is over three days, clean up the ink within the print head following its
cleaning method, inject a little cleaning liquid into it (Leave some cleaning liquid in
the print head when doing the cleaning.)Meanwhile, moisturize the nozzle surface
with the wet protection tray according to method 2. In addition, replace non-woven
fabrics in the wet protection tray every three days and inject new cleaning liquid into
it.
3. Scrubbing the nozzle panel
Every time when pressing ink with positive press or after cleaning the print head,
scrub the nozzle panel. Wipe away residual ink and cleaning liquid on the nozzle
panel, to prevent it droping onto the printer or print media.
When scrubbing the nozzle panel, dedicated non-woven fabrics should be used, and
make sure of its cleanness. Non-woven fabrics contaminated by dust, stain or water,
especially the one which has been used to scrub ink, should not be used to wipe the
nozzle panel, as ink on it can lead to a seriously blocked nozzle.
Scrub the nozzle panel along a single direction rather than back and forth. Do not
scrub it with great strength, but touch it lightly, to avoid damage of nozzle surface.
Dispose the used non-woven fabrics properly. Do not reuse it.
4.
To guarantee print quality, please make sure every nozzle on the print head is in good
condition, whose condition can be improved by pressing ink with positive Negative

pressure or doing the cleaning. The following items are very important to guarantee
the nozzle condition.
The requirement of printer’s working environment shall be maintained well,

especially the temperature. The print head temperature shall be between 150C and
300C.Print quality may be affected if the temperature is below 150C or above 300C.
Make sure the print head exhaust completely, and no bubble remains in it.
Adjust voltage and negative pressure of print head. A higher print head voltage can
improve the accuracy and color saturation of ink droplets, but it can cause the ink
outflow to be frequently broken as well.
Ink Use Guidelines
1. Safety instructions:
Some chemical substances contained in ink are of very low toxicity and irritation, which
will irritate eyes and respiratory system and cause allergic reaction. Contact with ink can
be effectively reduced with sound ventilating device and personal protective devices. When
dealing with ink, acrylic gloves and work clothes should be worn. If ink spills onto the
skin, it should be washed immediately with soap-suds. Eating, drinking and smoking are
forbidden in the workspace.
2. Storage of ink:
Ink should be stored in sealed containers and placed in a cool, dry place with good ventilation
no long-period exposure to light (including indoor sunlight, illumination light, etc ) and with
temperature of 10 ～ 40 . Although ink has a storage duration of 24 months, it
recommended to use it up within 12 months. Pay attention to the production date. Out-of-date
ink cannot be used.
Appendix I: Detailed Setting of Vacuum pressure gauge

Panasonic DP-101 digital Negative pressure switch is specially designed to inspect
and control vacuum, whose range is -100~-100KPa. 4-core interface is applied to
the control signal line and negative pressure gauge, which is completely compatible
with ink plate as well as SMC ZSE 30A. DP-101 Pressure gauge has two display
screens, among which the main display shows real-time value, while the minor
screen shows the setting value.
( A ) Calibration of reference pressure of the pressure gauge ( When setting parameters for the
first time, the method below must be followed) .

The calibration of its reference pressure has already been completed when ex-factory, i.e. standard
atmospheric pressure is set as the datum zero. Normally, calibration is not required.
When reference pressure changes due to some unpredictable factors, pressure calibration is required.
Otherwise, the displayed Negative pressure would deviate from actual pressure.
Calibrating method: 1. Disassemble the air tube behind the pressure gauge,
2. Energize the pressure gauge, and some value will be shown on its screen.
3. Press both ▲and▼ buttons for over 2 seconds at the same time, and the
main display will show the value 0.0.
Calibration of reference pressure has been completed.
( B) Working mode
The negative pressure gauge always display “RUN Mode”, while “Menu Setting Mode” is used
for basic setting, and “PRO Mode” is used for advanced functionalities, .
Under “RUN Mode”, reference values can be adjusted, locked and so on. Under “Menu Setting
Mode”, basic settings, such as setting the output mode and switching between NO and NC, can
be operated. Under “PRO Mode”, advanced functionalities like Hysteresis adjustment and copy
function, can be set.
During the normal operation of “RUN Mode”, by pressing “MODE” button, the mode
switching button, for 2 seconds, it will switch to “Menu Setting Mode”, while by pressing
“MODE” button for 5 seconds, it will switch to “PRO Mode”.
( C) Output mode and setting

As for comparison output 1 and comparison output 2, output mode can be chosen among EASY Mode
as well as Hysteresis Mode and Window Comparator Mode.
1. Long press “MODE” button for 2 seconds to enter Menu Setting, and the main display shows
EASY while the minor screen shows OUT1.
2. Through pressing ▲and▼ button, to set OUT1 output mode and select EASY mode,
Hysteresis mode or Window Comparator mode. It shows EASY for the first energizing.
The picture below shows the display interface of the negative pressure
gauge.
( EASY Mode) (Hysteresis Mode) (Window Comparator Mode )
3. Press “MODE” button to enter OUT2 setting, the main display shows OFF for the first
energizing. Through pressing ▲and▼ button, to set OUT2 output mode. The picture below
demonstrates display interface of the negative pressure gauge.

4. Press “MODE” button to enter NO/NC switching interface, and select NO/NC through
▲and▼ buttons. We set output 1 as NO and output 2 as NC. The picture below shows the
display interface of the negative pressure gauge.
5. Press “MODE” button to enter response time setting, and set default time as 2.5. The picture
below shows the display interface of the negative pressure gauge.
6. Press “MODE” button to enter color conversion setting of the main display, and choose the
color of main display through ▲and▼ buttons. The picture below shows the display interface
of the negative pressure gauge.
7. Press “MODE” button to enter unit setting. The default unit of negative pressure gauge is
shown as KPa, which is the unit we need. Unit could be selected through ▲and▼ buttons. The
interface is shown as the picture.
8. By this time Menu setups have been circled a circle. Press “MODE” button once again to
return. The main display shows actual air pressure values.Or long press “MODE” button for 2
seconds during the setting to return to the home page.
9. Long press for 5 seconds to enter into “PRO Mode” , under which we only need to set
Hysteresis fixed value as 11.With the default value 111, the negative pressure gauge
fluctuates too frequent in the process of control. Operation procedure: Press “MODE”
button three times, and the interface of the Pressure gauge is shown like this
Through ▲and▼ buttons adjust the value to

Long press “MODE” button for 5 seconds and return to the home page.
10. Press“MODE” button to enter P-1 and P-2 value setting, and set the value as the pressure
imposed on the ink-feeding system during normal operation.
Note:
1. Above values are common-used setting values. Specific values may be sort of
different.
2. The instantaneous display of pressure gauge at its being energized is not in measuring
status, but as follows:
It means that the pressure gauge will enter the working state after being energized for 5 seconds.

PZR KV 1 - Operation Manual

Uploaded by

Document Informationclick to expand document information

Document Informationclick to expand document information

Copyright:

Available Formats

PZR KV 1 - Operation Manual

Uploaded by

Document Information

Original Title

Copyright

Available Formats

Share this document

Share or Embed Document

Sharing Options

Did you find this document useful?

Is this content inappropriate?

Copyright:

Available Formats

PZR KV 1 - Operation Manual

Uploaded by

Copyright:

Available Formats

LIYU PZR-KV-1 Series High Speed

First edition September 15th, 2015

Second edition March 3rd, 2016

Copyright © 2015 All rights reserved for LIYU DMS GmbH

off and how to set various parameters of the printer.

following main categories:

List of machine models:

Adopts KM512iLNB type print head, with 4 Maximum Resolution: 1440dpi,

Adopts KM512iLNB type print head, with 4 Maximum Resolution: 1440dpi,

LIYU-PZR-KV-1-Series Manual www.liyu-dms.com -2-

List of main technical specifications:

Print Tech. Piezo continuous drop-on demand(DOD)

Print Head KM512iLNB (30pl)

Resolution 30pl:720 x 1440. Note 1

Ink Type Eco-solvent ink

Color Profile KCMY

Table Pressure 50kg/m2

Power Requirement 110V / 220±10%, ＞30A, 50 / 60Hz

Durability Two years outdoor

LIYU-PZR-KV-1-Series Manual www.liyu-dms.com -3-

LIYU-PZR-KV-1-Series Manual www.liyu-dms.com -4-

Printing efficiency list

Print head KM512iLNB (30pl)

LIYU-PZR-KV-1-Series Manual www.liyu-dms.com -5-

Machine optional components

Optional Components Functional Description Configuration Method

Automatic Measuring It can automatically measure the medium width Upgradeable

Single Roller Feeding Double-roller feeding system is applied to Configure to Order

Black cloth detecting function is not applied to Configure to Order

Upgradeable: The components can be upgraded for customers afterwards.

LIYU-PZR-KV-1-Series Manual www.liyu-dms.com -6-

Please refer to the attachment Packing List for detailed information.

LIYU-PZR-KV-1-Series Manual www.liyu-dms.com -7-

some cases. Please operate in strict accordance with instructions.

damage of print head.

staff’s physical health.

which may cause machine damage.

environmental protection department.

LIYU-PZR-KV-1-Series Manual www.liyu-dms.com -8-

unnecessary casualties, please carefully read the following safety precautions:

power outlet at the same time to avoid fire disaster.

identification at the bottom-left corner of the equipment. Otherwise, disturbance

may be caused and lead to abnormal image printing of the machine.

disaster, electric shock and other accidents may be caused.

local dealer if necessary:

1. The switch is insensitive or doesn’t work.

2. When the inkjet printer makes abnormal sound or produces smoke.

4. When problems that operators fail to settle arise.

LIYU-PZR-KV-1-Series Manual www.liyu-dms.com -9-

connecting outlet must be solid and reliable.

2. Relatively stable power supply in accordance with technical specification of

inkjet printer shall be used.

outlet with other equipment.

may cause equipment fault or damage electrical component of the equipment

(including print head).

be sure to disconnect the power of inkjet printer. otherwise, personal injury or

machine damage may occur.