CNT 0010357 02

Special Vehicle Series : 06
© Canon Inc. © Keisuke Saka+Kohei Masukawa
Chemical Fire Engine Assembly

Instructions
View of completed model
* This model was designed for

Papercraft and may differ from
the original in some respects.
Tools Assembly tip
Scissors Write the number of each part on the reverse side of the part in pencil
Ruler, set square upon cutting it out, to be sure you can tell which part is which later.
Glue (Wood glue or craft glue recommend) Before gluing, crease the paper along
Exhausted ballpoint pen (out of ink) mountain and valley fold lines. Trace along
Toothpicks (for use in applying glue) the folds with a ruler and an exhausted
Tweezers (useful for handling small parts) ballpoint pen (out of ink) to get a sharper fold.
Pencil Make sure rounded sections are nice and stiff.
Key to symbols
Pattern Assembly instructions

Mountain fold The dots show where to glue Red arrow
Dotted line
Fold so that the printed the pieces together. Glue the Glue
pattern faces outside. pieces together as shown in the
Blue arrow Insert
Dashed and following examples.
dotted line Some parts must be glued (without gluing)
Valley fold
Fold so that the printed together along the cut surfaces.
pattern faces inside. Light blue Glue tab
Red dot
Solid line Cut parts out Glue parts with the same
along this line. number together. (Numbers are Reverse side of
Light grey
not printed on very small parts.) paper
Solid blue line Cut a notch Green dot
Movable part
along this line. Glue areas within the same
part together. This denotes a part
that must be able to
Cut these areas move after the model
Diagonal Blue dot is completed.Be sure
grey lines out. Glue to the reverse side of the to crease these parts
specified part. sufficiently.
Glue, scissors and other tools may be dangerous to young children

so be sure to keep them out of the reach of young children.
Assembly Instructions: Eight A4 sheets (No. 1 to No. 8)

Build this model with careful reference to the Assembly Instructions.
Assembly
Chemical Fire Engine Instructions © Canon Inc. © Keisuke Saka+Kohei Masukawa
Assemble the cab.

Glue flaps a, b, c, and d in order.
Attach parts 6 & 7 to part 5,

and parts 10 & 11 to part 9, and assemble.
Fold mudguard sections

of parts 4 & 8 in two
and attach.
Glue flaps a, b, and c in order.
Refer to for completed image.

Assembly
Glue sections a, b, c, and d of part 17 in order.
Assemble with patterned

surface on the inside.
Front
Front
Front
Attach part 18
to rear.
Rear
Front
Don't forget to glue

rear section.
As seen from rear.
Rear
Rear
On sides, insert and

glue flaps only.
Assembly
Score the fold lines on part 26 and

bend firmly into curved shape.
Confirm position of sections to be glued and

insert between and . Do not glue .
Pull the edge of to open and

close shutter.
Assembly
Assemble front tires. Assemble front pair of Assemble rear pair of

rear wheels. rear wheels.
Attach the tires according to the diagram below.
Front
Rear
Assembly
Attach part 34 by sandwiching

part 35 between glued sections.
Roll and glue to form hose.

Hose is able to move up and down.
Insert nozzle; do not glue.
Glue parts with no glue tabs to

the areas cut out of the paper parts.
Roll part 67, insert in opening in part 66,

and glue to reverse side of paper.
Assemble parts 79 to 86 and glue in order,

beginning with part 79.
Assembly
Assemble parts 89 to 96 and glue in order,

beginning with part 89.
Assemble the hose car. Assemble part 28 with the patterned

surface to the inside, and insert into Glue parts 31 and 32 together.
part 4.
Don't forget to cut out center.
Glue handle section.
Don't forget to cut out

and fold crease.
Assembly
Refer to the finished photo

and attach small parts.
Fold one section each on

parts 41 and 42 and glue
to body.


Spe
cial
Che Veh
mic icle
Ser
al F ies
FO
AM ire E
TE ngin
ND
ER e
Finished!
Hose car can be collapsed Last, assemble the nameplate
for carrying on rear deck. and display it together with
your model.

CNT 0010357 02

Uploaded by

Copyright:

Available Formats

CNT 0010357 02

Uploaded by

Document Information

Original Description:

Original Title

Copyright

Available Formats

Share this document

Share or Embed Document

Sharing Options

Did you find this document useful?

Is this content inappropriate?

Copyright:

Available Formats

CNT 0010357 02

Uploaded by

Copyright:

Available Formats

Special Vehicle Series : 06

© Canon Inc. © Keisuke Saka+Kohei Masukawa

Chemical Fire Engine Assembly

View of completed model

* This model was designed for

Tools Assembly tip

Pattern Assembly instructions

Glue, scissors and other tools may be dangerous to young children

Assembly Instructions: Eight A4 sheets (No. 1 to No. 8)

Assemble the cab.

Attach parts 6 & 7 to part 5,

Fold mudguard sections

Glue flaps a, b, and c in order.

Refer to for completed image.

Glue sections a, b, c, and d of part 17 in order.

Assemble with patterned

Don't forget to glue

On sides, insert and

Score the fold lines on part 26 and

Confirm position of sections to be glued and

Pull the edge of to open and

Assemble front tires. Assemble front pair of Assemble rear pair of

Attach the tires according to the diagram below.

Attach part 34 by sandwiching

Roll and glue to form hose.

Glue parts with no glue tabs to

Roll part 67, insert in opening in part 66,

Assemble parts 79 to 86 and glue in order,

Assemble parts 89 to 96 and glue in order,

Assemble the hose car. Assemble part 28 with the patterned

Don't forget to cut out center.

Glue handle section.

Don't forget to cut out

Refer to the finished photo

Fold one section each on

Glue parts with no glue tabs to

Glue parts with no glue tabs to

You might also like