This document provides specifications for a sensor faucet including:
- It can operate with cold or hot water between 5-65 degrees Celsius.
- The default water flow rate is 12.17 LPM but can be adjusted down to rates like 1.3 LPM using flow regulators.
- It has a brass composition and uses a 6V battery as a power source.
- Settings like detection range and follow up time can be adjusted via infrared touch.
This document provides specifications for a sensor faucet including:
- It can operate with cold or hot water between 5-65 degrees Celsius.
- The default water flow rate is 12.17 LPM but can be adjusted down to rates like 1.3 LPM using flow regulators.
- It has a brass composition and uses a 6V battery as a power source.
- Settings like detection range and follow up time can be adjusted via infrared touch.
This document provides specifications for a sensor faucet including:
- It can operate with cold or hot water between 5-65 degrees Celsius.
- The default water flow rate is 12.17 LPM but can be adjusted down to rates like 1.3 LPM using flow regulators.
- It has a brass composition and uses a 6V battery as a power source.
- Settings like detection range and follow up time can be adjusted via infrared touch.
This document provides specifications for a sensor faucet including:
- It can operate with cold or hot water between 5-65 degrees Celsius.
- The default water flow rate is 12.17 LPM but can be adjusted down to rates like 1.3 LPM using flow regulators.
- It has a brass composition and uses a 6V battery as a power source.
- Settings like detection range and follow up time can be adjusted via infrared touch.
Sensor Faucet for Wash Basin Wall Mounted Complete with Installation Box (Battery Description Operated) Water Supply Cold and hot water (2 inlets) Water Temperature 5 ºC - 65 ºC Inlet Water Connection 1/2”BSP / 15mm Flow Rate 12.17 LPM @ 3 bar By using flow regulators (Product should be ordered with suffix as G-2.5 LPM, GA-6.0 LPM, Flow regulator GB-8.0 LPM, GD-3.8 LPM & GE-1.3 LPM @ 3.0 Bar pressure) one can regulate the flow rate. Recommended Water 0.5 Bar - 6.0 Bar Pressure Brass Ingots as per IS:1264-1997 Cu (58.0-63.0), Sn (0.0-1.0), Pb (0.5-2.5), Ni (0.0-1.0), Al (0.2-0.8), Mn (0.0-0.5), Total Impurity (0.0-2.0), Zn(Remainder) Material Composition Specification in Brass Rod as per IS:319-1989 Percentage Cu (56.0-59.0), Pb (2.0-3.5), Fe (0.0-0.35), Total Impurity(0.0-0.7), Zn( Remainder)
SS Plate as per AISI: 304
Ni (8.0 -11.0), Ch (18.0 - 20.0), Mn (0.0 - 2.0), Ca (0.0 - 0.08), Fe (Remainder) Operating pressure 0.5 - 6.0 bar Solenoid Valve Nominal Voltage : 6 Volt DC Specification IP67 Protected : Very robust, reliable solenoid valve Low power consumption : Bi-stable pulse controlled
Electronic Parameter Setting Procedure IR Touch ( No need of remote controller )
Detection Range : 1 - 8 level, default : 6,
Adjustable Parameters Follow up Time : 1 - 10 seconds, default : 1-2 Second In line purge feature : (Range - off, 12hrs ,24 hr, 48 hrs), default : off Power Source 6 Volt Battery - Duracel CR-P2 Ultra Lithium 223 , 1400mAh Plating: Nickel-10.0 micron Chromium-0.3 micron Finish Salt Spray (500 hrs + Validated) Adhesion (Pass) Aerator Size WRAS, ACS Approved (M 24X1) Available Color Finishing Satinless Steel (STL) DISCLAIMER: Our every effort has been made to ensure factual accuracy, the information presented subject to changes due to requirements in different sites, markets and/ or countries. 10% variation in flow rate may be possible. Jaquar reserves the right to make the necessary amendments at any time without prior notice.
