Analog Circuits (Ecen 2101)

B.
TECH/CSE/ECE/IT/3RD SEM/ECEN 2101/2021

B.TECH/CSE/ECE/IT/3RD SEM/ECEN 2101/2021
ANALOG CIRCUITS
(ECEN 2101)
Time Allotted : 3 hrs Full Marks : 70

Figures out of the right margin indicate full marks.
Candidates are required to answer Group A and
any 5 (five) from Group B to E, taking at least one from each group.
Candidates are required to give answer in their own words as far as practicable.
Group – A
(Multiple Choice Type Questions)
1. Choose the correct alternative for the following: 10 × 1 = 10

(i) The slope of the load line depends on
(a) type of the diode used (b) characteristic curve
(c) load resistor (d) source voltage.
(ii) A circuit that removes positive or negative part of an ac signal is called
(a) Clipper (b) Clamper
(c) Amplifier (d) Oscillator
(iii) Maximum power efficiency that can be achieved by Class A power amplifiers is
(a) 25% (b) 78.5% (c) 50% (d) 30%.
(iv) Which one of the following oscillator is used for the generation of high
frequencies?
(a) R-C phase-shift (b) L-C oscillator
(c) Wien-bridge (d) none of the above.
(v) A zero-crossing detector is an application of a
(a) Differentiator (b) Integrator
(c) Summing Amplifier (d) Comparator.
(vi) The best frequency stability is obtained by using
(a) Colpitts oscillator (b) Hartley oscillator
(c) Wien Bridge oscillator (d) Crystal oscillator.
(vii) In an ideal op-amp, which is not true?
(a) Open loop voltage gain is infinite (b) Input resistance is infinite
(c) Slew rate is infinite (d) CMRR is zero.
(viii) In a Common Base BJT based circuit, for a fixed emitter base junction forward
bias, increase in reverse bias across the collector base junction,
(a) increases emitter current (b) decreases emitter current
(c) keeps emitter current constant (d) makes emitter current zero
ECEN 2101 1
(ix) In an LC oscillator, the frequency of oscillator is ……………. L or C.
(a) Proportional to square of
(b) Directly proportional to
(c) Independent of the values of
(d) Inversely proportional to square root of
(x) Crossover distortion can be observed in
(a) class-AB amplifier (b) class-A amplifier
(c) class-B amplifier (d) class-C amplifier.
Group- B
2. (a) Why is the stability of Q point essential? Derive the stability factor (with respect
to ICO) for a collector to base bias circuit. [(CO2) (Remember/LOCQ)]
(b) In the fixed bias circuit as shown in Fig.1. VCC=15V, RC=2 kΩ, RB=300 kΩ, β=100,
VBE=0.7V. Neglect ICO. Determine
(i) Base current IB
(ii) The quiescent point
Fig.1
[(CO2)(Apply/IOCQ)]
(2 + 4) + (2 + 4) = 12
3. (a) Draw the hybrid parameter model of a bipolar junction transistor. Define the
four hybrid parameters. [(CO2)(Remember/LOCQ)]
(b) The input signal vi is a sinusoid having an amplitude of 10V, VB1=8V and VB2=6V.
Draw the output voltage waveform vo. Diodes D1 and D2 are ideal.
Fig.2
[(CO1) (Evaluate/HOCQ)]
(c) Using the small signal model of BJT, derive expressions of input impedance
Zi, and voltage gain Av of a fixed bias amplifier circuit. [(CO3)(Analyse/IOCQ)]
4 + 4 + 4 = 12
ECEN 2101 2
Group - C
4. (a) A Wien Bridge oscillator has a frequency of oscillation1 kHz and a capacitance of
100pF. Find the value of resistance required. [(CO4) (Create/HOCQ)]
(b) Sketch the circuit diagram of a Phase shift oscillator. Calculate the frequency of
the oscillation and the condition for sustained oscillation.
[(CO4)(Analyse/IOCQ)]
4 + 8 = 12
5. (a) What is the effect of negative feedback on the output impedance of voltage-
series feedback amplifier? [(CO4) (Remember/LOCQ)]
(b) Determine voltage gain, input and output impedance for voltage shunt feedback
having A=-120, Ri=2.2 kΩ, Ro=22 kΩ and β=-0.1. [(CO4) (Analyse/IOCQ)]
(c) Sketch the circuit diagram of a Hartley oscillator. If the parameters of the
oscillator are:
L1=500µH, L2=5mH, M= 300µH, C=150pF. Find the frequency of oscillation.
3 + 3 + (3 + 3) = 12
Group - D
6. (a) Explain the operation of an instrumentation amplifier with proper circuit
diagram. [(CO5) (Remember/LOCQ)]
(b) Design and draw the circuit for following operation using op - amp.:
V0= V1+ V2– 2V3 where V1, V2 , V3are input voltage signals and V0 is the output
voltage signal. [(CO5) (Create/HOCQ)]
(c) Draw the circuit diagram of a Schmitt trigger circuit. [(CO5)(Remember/LOCQ)]
6 + 4 + 2 = 12
7. (a) In the Fig. 3. If V1=0.5V and V2=0.1V, find Vo.
Fig.3
[(CO5) (Apply/IOCQ)]
(b) Draw the circuit diagram of a half wave Precision rectifier circuit.
[(CO5) (Remember/LOCQ)]
(c) What is a current mirror and why is it called so? Explain with proper circuit
diagram the working of current mirror. [(CO5)(Analyse/IOCQ)]
4 + 2 + (2 + 4) = 12
ECEN 2101 3
Group - E
8. (a) A class B push pull power amplifier is supplied with Vcc=50 V. The signal swings
the collector voltage down to Vmin=5V. The total dissipation in both transistors
is 40 W. Find the total power and conversion efficiency. [(CO6) (Apply/IOCQ)]
(b) Draw the circuit diagram of a push pull amplifier. List the advantages of the
circuit. [(CO6) (Remember/LOCQ)]
(c) What is cross over distortion? [(CO6)(Understand/LOCQ)]
4 + (4 + 2) + 2 = 12
9. (a) Draw the circuit diagram and explain the operation of a monostable
multivibrator using a 555 timer IC. Derive the expression for output pulse
width. [(CO4) (Analyse/IOCQ)]
(b) Determine the frequency and duty cycle for 555 Astable multi-vibrator output
for C=0.01 µF, RA=2 kΩ and RB=100 kΩ.
Fig.4
(6 + 2) + 4 = 12
Cognition Level LOCQ IOCQ HOCQ

Percentage distribution 32% 45% 23%
Course Outcome (CO):

After the completion of the course students will be able to
1. Apply the previous knowledge gathered from Basic Electrical and Basic Electronics
papers.
2. Understand the concepts of BJT, MOSFET and biasing techniques of BJT and MOSFET
based amplifier circuits.
3. Analyse frequency response of amplifier circuits.
4. Design different types sinusoidal oscillators and multivibrator circuits.
5. Construct algebraic equation-based amplifier and analog computers using OP-AMP
6. Design stable high-gain amplifier circuits.
*LOCQ: Lower Order Cognitive Question; IOCQ: Intermediate Order Cognitive Question;
HOCQ: Higher Order Cognitive Question
ECEN 2101 4
Department &
Submission Link
Section
CSE A https://classroom.google.com/u/0/w/NDA1MTI0NjA5Mjg0/tc/NDY4MDA0NTc1NzI4
CSE B https://classroom.google.com/u/0/w/NDA0OTUzODA2MDY2/tc/NDc1MTUyODE2MTg0
CSE C https://classroom.google.com/c/NDA1MTk5NjAxMzQz/a/NDc1MTUwNzQxNTU5/details
ECE A https://classroom.google.com/w/NDA1Mjk2MTM3OTI2/tc/NDc0ODUyMTUwODE0
ECE B https://classroom.google.com/c/NDA1MTk2NjIwMTI5/a/NDc0ODU1MDAwNjQy/details
ECE C https://classroom.google.com/c/NDA1MzQyNTU4NDkz/a/NDc1MTUwMzAyMzI4/details
IT https://classroom.google.com/w/NDQyMjEzNzM4MDY1/tc/NDc3MzIyOTM5Njgx
ECEN 2101 5

Analog Circuits (Ecen 2101)

Uploaded by

Copyright:

Available Formats

Analog Circuits (Ecen 2101)

Uploaded by

Document Information

Original Title

Copyright

Available Formats

Share this document

Share or Embed Document

Sharing Options

Did you find this document useful?

Is this content inappropriate?

Copyright:

Available Formats

Analog Circuits (Ecen 2101)

Uploaded by

Copyright:

Available Formats

B.

TECH/CSE/ECE/IT/3RD SEM/ECEN 2101/2021

Time Allotted : 3 hrs Full Marks : 70

1. Choose the correct alternative for the following: 10 × 1 = 10

7. (a) In the Fig. 3. If V1=0.5V and V2=0.1V, find Vo.

Cognition Level LOCQ IOCQ HOCQ

Course Outcome (CO):

You might also like