LX3V 2adi BD

LX3V-2ADI-BD
User manual
Website: http://www.we-con.com.cn/en
Technical Support: support@we-con.com.cn
Skype: fcwkkj
Phone: 86-591-87868869
QQ Group: 465230233
Technical forum: http://wecon.freeforums.net/
LX3V-2ADI-BD
1. Mounting instruction
Make sure to power off the PLC before mounting the LX3V-2ADI-BD module and removing the top
cover of PLC, screwed to the PLC.
Caution:
1) This BD module only support the following firmware versions or later. Users can check the PLC
firmware version in D8001.
 LX3VP:25103;
 LX3VE: 25201;
 LX3V-A2:25014;
 LX3V-A1: 22006;
2) When mounting module to PLC, all the lights are blinking after power ON PLC, it means this PLC
can’t support LX3V-2ADI-BD, please purchased new PLC.
3) Please fixed BD module on the PLC, poor contact may lead to failure.
4) BD module and top cover of PLC’s tightening torque is 0.3 ~ 0.6 N.m.
Warring:
Make sure to power off the PLC before mounting or removing the BD module and put the cover in
right place.
2. Special feature
1) LX3V-2ADI-BD module equips with 2 channels analog input. This module will be mounted in the
PLC.
2) The input current of LX3V-2ADI-BD module between 4 mA to 20mA, and the digital value will be
saved in special system address, but the numerical relationship between input and output value
cannot be changed.
Table 2-1 description of system address
Expansion port 1 (far away from PLC light)
Address Description
The flag of switching Input mode in CH1
M8112
OFF: Current input mode (4mA~20mA, 0~2000) ON: Retain
M8113 The flag of switching Input mode in CH2
1 WECON Technology Co., Ltd.

LX3V-2ADI-BD
OFF: Current input mode (4mA~20mA, 0~2000)

D8112 The digital value of channel 1; (4mA~20mA, 0~2000)
Expansion port 2 (near PLC light)
Address Description
M8116
ON: Retain
M8117
3. Dimension
IN-2ADI input current range: 4-20mA

I1+ Anode of the channel 1 current input
I1- Cathode of the channel 1 current input
• No connection
I2+ Anode of the channel 2 current input
I2- Cathode of the channel 2 current input
LED lights indicating:

1) LED1: power led power on always.
2) LED2: flashes when communications.
3) LED3 (AD 1): On indicates enable, OFF indicates disable, flicker indicates exceeding the
measurement range.
4) LED4 (AD 2): On indicates enable, OFF indicates disable, flicker indicates exceeding the
measurement range.
5) If the BD module plugged into the old firmware version when on the host, all LEDs will
be flashing.

LX3V-2ADI-BD
4. Specification
1) Please refer to the LX3V user manual for the general specification of LX3V-2ADI-BD;
2) LX3V-2ADI-BD is powered supply by LX3V main unit;
3) Performance
Table 4-1
Specification
Item
Current input
Input range DC 4-20mA (Input resistance:250Ω)
Digital output 12 bits binary
Resolution 8uA (4mA-20mA/2000)
Precision ±1% (4-20mA: ± 0.16mA)
AD conversion time One PLC scanning cycle
Characteristic
Insulation No insulation in each PLC channel

Occupied points None
5. Wiring
Caution:
1) Do not put the LX3V-2ADI-BD module near high-voltage power cable. Keep away the power
cable at least 100mm;
2) Do not solder any terminal with the others device;
3) Do not connect any unsuitable cable;
4) Please fix cable;
5) Do not connect any unit to the unused terminal;

LX3V-2ADI-BD
5.1 Suitable cable

Connect to output device with AWG25-16.
Max tighten torque of terminal is 0.5 to 0.6N.m.
Table 5-1
Line type Cross sectional area(mm2) End-of-pipe treatment
AWG26 0.1288 Stranded cable: stripped jacket, rub
...... ...... Conductor, then connect the cable.
Single-core cable: stripped jacket,
AWG16 1.309
Then connect the cable.
5.2 Input
6. Example
The analog value (4~20mA) in each channel will be saved in system address (D8112, D8113). It will
be saved automatically when “END”, and convert into digital value.
6.1 Basic program

Caution:
1) Trigger M8122 and M8113, and set the characteristic of conversion.
2) Do not change the value of D8112 and D8113.
AD conversion:

LX3V-2ADI-BD
Set channel 1 as current input (4~20mA)

Set channel 2 as current input (4~20mA)
Save the value of channel 1 to D0
Save the value of channel 2 to D2
6.2 Application example

LX3V-2ADI-BD has no offset and gain function.
Caution:
1) There are extra program for multiplication and division, so the real accuracy and resolution of
analog-digital conversion are different from product specifications;
2) The range for analog output is constant;
Current input mode

1) In current input mode, it changes the analog value (4-20mA) to digital value (0-2000). If users
need 4000-20000 digital range, it requires a conversion.
2) As following program shows, the digital value is saved in D8112 and D8113, because the digital
range is changed from 0-2000 to 4000-20000, so the resolution of LX3V-2ADI-BD is not 8uA.
3) Suppose the user needs 4000-20000, and save in D0, so D0=8*(D8112 or D8113) +4000, the
program as following shows.

LX3V 2adi BD

Uploaded by

Copyright:

Available Formats

LX3V 2adi BD

Uploaded by

Document Information

Original Title

Copyright

Available Formats

Share this document

Share or Embed Document

Sharing Options

Did you find this document useful?

Is this content inappropriate?

Copyright:

Available Formats

LX3V 2adi BD

Uploaded by

Copyright:

Available Formats

LX3V-2ADI-BD

1 WECON Technology Co., Ltd.

OFF: Current input mode (4mA~20mA, 0~2000)

IN-2ADI input current range: 4-20mA

LED lights indicating:

2 WECON Technology Co., Ltd.

Insulation No insulation in each PLC channel

3 WECON Technology Co., Ltd.

5.1 Suitable cable

6.1 Basic program

4 WECON Technology Co., Ltd.

Set channel 1 as current input (4~20mA)

6.2 Application example

Current input mode

5 WECON Technology Co., Ltd.

You might also like