Location via proxy:   [ UP ]  
[Report a bug]   [Manage cookies]                

UG Academic Handbook - Archit - Final

Download as pdf or txt
Download as pdf or txt
You are on page 1of 34

ACADEMIC REGULATIONS

1. ACADEMIC PROGRAMMES 4.3 Academic Term:


1.1 The institute offers Bachelor of Technology (B.Tech.), Master of 4.3.1 Semester system of 16 weeks duration with continuous and
Technology (M.Tech.) and Master of Computer Applications comprehensive assessment is followed.
(MCA) programmes of Manipal University. 4.3.2 Each semester has a specified course structure.
1.2 Duration of the B.Tech. programme is 8 semesters. 4.3.3 The first year B.Tech. course structure is common to all branches
1.3 Duration of M.Tech. and MCA programme is 4 semesters. of Engineering.
1.4 The maximum duration for a student for complying with the 4.3.4 The medium of instruction for all courses offered is English.
Degree requirement is twice the duration of the academic 4.3.5 Eighth semester of B.Tech. programme, fourth semester of MCA
programme from the date of joining. programme as well as third & fourth semesters of M.Tech.
programme is fully dedicated to project work.
2. ADMISSION PROCEDURE
2.1 Undergraduate Programme (B.Tech.): 4.4 Course Numbering:
Eligible students are admitted on the basis of the rank obtained in 4.4.1 The courses offered by each Department are coded with 3 letters
the All India Manipal University Online Entrance Test. Seats are indicating the department offering the course followed by 4 digits.
reserved for NRI / Foreign students. 4.4.2 First digit indicates the level, second digit indicates semester
2.2 Post Graduate Programmes (M.Tech. / MCA): offered ('1': offered in ODD; '2': offered in EVEN; '0': offered in
Eligible students are admitted on the basis of the rank obtained in BOTH) and the last two digits indicate the serial number.
the All India Manipal University Online Entrance Test. Seats are 4.4.3 The following codes are used for different departments:
reserved for NRI / Foreign students.
DEPARTMENT CODE
3. ELIGIBILITY FOR ADMISSION
3.1 Undergraduate Programme (B.Tech.): Aeronautical and Automobile Engineering AAE
3.1.1 Pass in 10+2 or equivalent with Physics, Mathematics and Bio-medical Engineering BME
English as compulsory subjects along with Chemistry / Bio-Technology BIO
Biotechnology / Biology / any technical vocational subjects as
optional; with a minimum of 50% marks taken together in Chemical Engineering CHE
Physics and Mathematics and any one of the optional subjects. Civil Engineering CIE
3.1.2 Holders of three years Diploma in Engineering awarded by the Computer Science and Engineering CSE
Board of Technical Education in Karnataka or equivalent / B.Sc.
Electronics and Communication Engineering ECE
Degree with Mathematics as one of the subjects; securing an
aggregate of at least 50% marks are eligible to join Third Electrical and Electronics Engineering ELE
semester under lateral entry scheme. Information and Communication Technology ICT
3.1.3 Eligible NRI / Foreign students are admitted based on their Instrumentation and Control Engineering ICE
qualifying examination performance.
Mechanical and Manufacturing Engineering MME
3.2 Post Graduate Programmes: Mechatronics MTE
3.2.1 M.Tech.: Print and Media Engineering PMT
3.2.1.1 BE / B.Tech. / AMIE or equivalent in relevant branch with a
minimum of 50% aggregate marks in qualifying examination Physics PHY
3.2.1.2 Eligible NRI / Foreign students are admitted based on their Chemistry CHM
qualifying examination performance. Mathematics MAT
3.2.2 M.Tech. (Part-time): Humanities and Management HUM
3.2.2.1 Faculty/Staff sponsored from Manipal University only are
eligible to do part-time M.Tech. programme. Computer Applications MCA
3.2.2.2 Duration of M.Tech. (Part time) programme is 6 semesters.
3.2.3 MCA: 4.5 Credit Based System:
3.2.3.1 A bachelor's degree in Computer Applications / Computer 4.5.1 Each course, theory as well as practical, is expressed in terms of a
Science / Information Technology with a minimum of 50% certain number of credits. The credits are determined by the
aggregate marks in the qualifying examination. number of contact hours per week. For theory courses, 1 Hour
3.2.3.2 Eligible NRI / Foreign students are admitted based on their Lecture / Tutorial per week is assigned 1 Credit, where as for
qualifying examination performance. practical courses 3 contact hours per week is assigned 1 Credit.
4.5.2 Course work in each semester is expressed in terms of a specified
4. ACADEMIC PROCESS number of credits. A student successfully completes a particular
4.1 Registration: semester when he/she earns all the credits of that semester. A
4.1.1 Students have to register for the courses with the parent student earns full credits for a subject registered if he/she secures
department at the commencement of each semester on the day letter grade E or higher.
notified in the academic calendar. 4.5.3 Promotion of a student to higher semesters is based on securing a
prescribed minimum number of credits.
4.2 Pre-registration:
4.2.1 Students need to pre-register for elective courses (both program 4.6 Assessment:
& open electives) with their department for the next semester as 4.6.1 The academic performance of a student is assessed by the
notified in the academic calendar. course instructor/s concerned.

05
4.6.2 The student performance in each theory course is evaluated out of 4.8.4.1.3 There will be a mid-semester evaluation of the work done on
100 marks, of which 50 marks are for in-semester assessments the project after 8-10 weeks. This evaluation will be done by
and 50 marks are for end-semester assessments. the department concerned and will be out of 100 marks.
4.6.3 The in-semester assessment in theory courses is based on 4.8.4.1.4 The final evaluation and viva voce will be conducted after the
periodic tests, assignments, quizzes, case presentations, completion of the project work and submission of the project
seminars etc. which shall be defined by the course instructor. report by a panel of examiners including the internal guide.
4.6.4 The student performance in laboratory courses is also evaluated 4.8.4.1.5 In case of external projects, the feedback of the external guide
out of a maximum of 100 marks, and is based on in-semester shall be considered during evaluation.
assessment of 60 marks and examination conducted for 40 4.8.4.1.6 The end-semester evaluation of the project work is out of 300
marks. marks.
4.6.5 Course Instructors are to give the complete course plan approved 4.8.4.1.7 The grade awarded to the student will be on the basis of the
by the HoD, at the beginning of the semester. Course plan includes total marks obtained by him / her out of 400 marks.
lesson plan & evaluation plan of the course offered. 4.8.4.2 Second year M.Tech. / Fourth Semester MCA:
4.6.6 Course instructors are to give regular feedback on the 4.8.4.2.1 A student of M.Tech. shall carry out a Project Work for a
performance of students. minimum of 36 weeks during the second year of the
4.6.7 The performance of a student in a course is reflected in the Letter programme, in the institution/ industry/ research laboratory
Grade awarded. or any other institution where facilities exist with approval of
the parent Department.
4.7 Attendance Requirements: 4.8.4.2.2 There will be a mid-term evaluation of the work after about 18
4.7.1 All students must attend every lecture, tutorial and practical weeks by the department concerned.This evaluation will be
classes. out of 100 marks.
4.7.2 A student with less than 75% attendance in individual courses 4.8.4.2.3 In the case of the Fourth Semester MCA students, the minimum
shall not be permitted to write the end semester examination in that project duration is 16 weeks and there will be a mid-term
course and will be given DT letter grade in the course. evaluation by the department concerned after about 8weeks.
4.7.3 The aggregate percentage of attendance of the student during the 4.8.4.2.4 The final evaluation will be conducted after the completion of
semester will be entered in his/her grade sheet of that semester. the project work and submission of the dissertation by a
panel of examiners consisting of an internal guide.
4.8 Grading System: 4.8.4.2.5 In case of external projects, the feedback of the external guide
4.8.1 10 point grading system shown is used for awarding letter grade in shall be considered during evaluation.
each course. 4.8.4.2.6 The end-semester evaluation of the project work is out of 300
marks.
4.8.4.2.7 The grade awarded to the student will be on the basis of the
Letter Grade A+ A B C D E AP F/I/DT
total marks obtained by him / her out of 400 marks.
Grade Points 10 9 8 7 6 5 0 0
4.9 Class Committee:
AP: Audit Pass F: Failure I: Incomplete DT: Attendance shortage
4.9.1 A class committee headed by the Associate Director
4.8.2 The overall performance of a student in each semester is indicated (Academics) is formed for the first year B.Tech. progamme.
by the Grade Point Average (GPA) which is the weighted average The section coordinators, course coordinators and student
of the grade points expressed as representatives of all sections will be members of this
committee.
where 4.9.2 For III to VIII Semester of B.Tech. progamme and for every
n=Number of courses registered semester of M.Tech. & M.C.A. progamme, separate class
C=Course credits committees are constituted by the Heads of the respective
G=Grade points departments. The committee is formed with a senior faculty of the
Department as Chairman & Course Coordinators/Course
4.8.3The overall performance of the student for the entire programme is Instructors of all courses & student representatives as members.
indicated by the Cumulative Grade Point Average (CGPA) which is 4.9.3 Course Coordinator: If there is more than one section, one of
the senior faculty member is nominated by the HOD as
the weighted average of the GPA of all semesters expressed as
Course Coordinator.
4.9.4 Functions of the Class Committee:
4.9.4.1 The class committee will meet thrice in a semester.
where 4.9.4.2 The first meeting will be held within two weeks from the
N=Number of Semesters commencement of the semester in which the course plan,
evaluation plan etc. are discussed.
4.9.4.3 The second meeting will be held two weeks after the first test
4.8.4 Evaluation of Project Work Dissertation/ Thesis to collect feedback and improve the effectiveness of the
4.8.4.1 Eighth Semester B.Tech.: teaching learning process. Performance of the students in the
4.8.4.1.1 B.Tech. student shall carry out a Project Work for a minimum tests may also be analyzed.
of 16 weeks duration. 4.9.4.4 The Chairman of the class committee should send the
4.8.4.1.2 The Project Work can be carried out in the institution / minutes of the class committee meeting to the Associate
industry / research laboratory or any other institution where Director (Academics) through the Head of the Department
facilities exist with approval of the parent Department. after each class committee meeting.
06
4.9.4.5 The third meeting is to be held to analyse the performance of 4.13.1 A student who is not eligible for promotion from an even
the students in all courses of study and grade finalization. semester to the next higher semester for reasons of not
However the student representatives are exempted from this having earned the prescribed minimum number of credits will
meeting. be required to discontinue the academic programme
4.9.4.6 The Associate Director (Academics) will declare the results temporarily. In such case he/she will be put on academic
after processing. probation for the next academic year and a warning letter shall
be issued.
4.10 Section Committee: 4.13.2 If a student is repeating a semester/s due to poor academic
4.10.1 Each section of the first year will have a Section Committee, performance, he/she will also be put on academic probation.
consisting of the Section Coordinator, faculty members 4.13.3 The student put on academic probation shall be periodically
handling both theory and practical classes for that section monitored and mentored by the faculty advisor. He/she can
and student representatives as members. rejoin the academic programme after fulfilling the academic
4.10.2 The Section Coordinator will be a senior faculty member who requirements as in 4.11 at the end of the academic probation.
teaches at least one subject for that section. The Section 4.13.4 At the end of the academic probation year, if a student fails to
Coordinators will be nominated by the Associate Director acquire the minimum credits to get promoted to next higher
(Academics), who will administer the functioning of all the semester, his/her registration for the academic programme
Section Committees. shall be terminated.
4.10.3 The section committee will meet periodically to review the
overall effectiveness in the conduct of first year classes. 4.14 Rejoining a Programme:
A student who discontinues the academic programme for any
4.11 Faculty Advisors: reason and rejoins the programme at a later date shall be
4.11.1 To help the students in planning their courses of study and for governed by the rules, regulations, courses of study and
general advice regarding academic programmes the Head of syllabi in force at the time of his/her rejoining the programme.
the Department will assign one to two senior faculty
members in the III semester who will be Faculty Advisors for 4.15 End-Semester Examination:
the batch. 4.15.1 The end semester examination will be conducted only in the
4.11.2 Faculty Advisor for a particular batch will continue till the courses offered in the current semester.
regular students complete the programme. 4.15.2 A student should have appeared for the end-semester
examination of the prescribed course of study to be eligible
4.12 Promotion to Higher Semesters: for the award of a passing grade in the course.
4.12.1 B.Tech. Programme: 4.15.3 Only students with attendance ³ 75 % will be permitted to
4.12.1.1 Promotion of a student from an even semester to the next appear for the end semester examination.
higher (odd) semester is subject to securing the minimum 4.15.4 A separate minimum of 35% of marks in the end semester
academic performance specified. examination is essential to be awarded a passing grade in a
4.12.1.2 To be eligible for promotion to the third semester, a student theory course.
should have earned a minimum of 25 credits at the end of the 4.15.5 A student who earns a minimum of 5 grade points (E grade) in
second semester. a course is declared to have successfully completed the
4.12.1.3 To be eligible for promotion to the fifth semester, a student course, and earned the credits assigned to that course.
should have earned a minimum of 70 credits at the end of the 4.15.6 A course successfully completed cannot be repeated for
fourth semester. grade improvement. However in special cases students may
4.12.1.4 To be eligible for promotion to seventh semester, a student be allowed to reject and repeat the entire semester with the
should have earned a minimum of 115 credits at the end of consent of HoD/ Associate Director (Academics).
the sixth semester. 4.15.7 If a student is eligible for but fails to appear in the end-
semester examination due to valid reasons, he/she will be
4.12.2 M.Tech. Courses: awarded an 'I' grade (incomplete) on the grade sheet.
4.12.2.1 A student can start the project work at the beginning of the However, it needs approval of Associate Director
third semester only if she/he has acquired 40 credits at the (Academics).
end of the second semester, and he/she has to earn all the
credits of the first and second semesters, before he /she is
4.16 Make-up examinations:
permitted to submit the project thesis
4.16.1 Make-up examinations will be held at the end of the semester
4.12.2.2 A part-time M.Tech student can start the project work at the
break to help the students who have got F/I grade in the
beginning of the third year, but he/she has to earn all the
courses offered during the semester.
credits of course work, before he/she is permitted to submit
the project thesis 4.16.2 The cut-off marks for grades in the make-up examination will
be same as those in the regular end-semester examination.
4.12.3 M.C.A. Course: 4.16.3 However, for students who have once failed (F grade) in any
4.12.3.1 Promotion of a student from second semester to third course, a maximum of C grade only will be awarded in
semester is subject to securing a minimum of 30 credits at subsequent examinations irrespective of their performance.
the end of the second semester. 4.16.4 Those who miss regular examinations due to valid reasons (I
grade) will be allowed to retain whatever grade they secure in
4.13 Academic Probation and Termination of the registration to the make-up examinations.
programme:

07
4.17 Re-valuation of answer papers: 5.3 Merit list will be prepared based on the CGPA after the
4.17.1 A student may apply for the revaluation of end-semester declaration of second semester results.
examination by submitting an application along with the 5.4 Only students who have passed in all the subjects of I & II
specified fee. semesters are eligible for change of branch.
4.17.2 Those who apply for reevaluation will be able to see their 5.5 Students who have secured seats under any scholarship
answer papers along with the scheme of evaluation on a scheme and have opted for branch change will not be eligible
scheduled date. for the scholarship from the second year.
4.17.3 The fee will be refunded in case of any change in grade after 5.6 Mutual change of branch is not permitted.
revaluation.
6. TRANSFER OF CREDITS
4.18 Re-registration of courses: The courses credited elsewhere, in Indian/Foreign
4.18.1 Students with F/I/DT Grade are allowed to re-register for University/Institutions/Colleges/certified MOOC by students
subjects of lower semester along with their regular term during their study period at MIT Manipal may count towards
subjects by paying the prescribed fees. the credit requirements for the award of degree. The credit
4.18.2 Students may not be permitted to re-register in courses if transferred will reduce the number of courses to be registered
there are clashes in the time table. by the student at MIT. The guidelines of such transfer of
4.18.3 Students are allowed to register for a maximum of 36 credits
credits are as follows:
in a given semester.
4.18.4 Students are eligible to get actual grades in re-registered 6.1 B.Tech student with consistent academic performance and
courses. CGPA > 7 can credit the courses approved by the concerned
Department Curriculum Committee (DCC) and ratified by
4.19 Withholding of Results: Board of Studies (BoS) in Engineering of Manipal University,
Results will be withheld when a student has not paid his/her in other institutions during 3rd and 4th year and during semester
dues or there is a case of disciplinary action pending against breaks.
him/her. 6.2 Credit transferred will not be used for GPA/CGPA
computation. However credit transferred will be considered
4.20 Eligibility for the Award of Degree: for the overall credit requirements of the program.
4.20.1 A student will be eligible for the award of the degree if:
6.3 Students can earn external credits only from Indian/Foreign
4.20.1.1 He/she earns the required number of credits specified for all
Universities/Institutions with which MU/MIT has a MoU for
semesters.
4.20.1.2 He/she has paid all dues to the Institute. the above purpose.
4.20.1.3 No case of disciplinary action is pending against him/her. 6.4 Credit transfer can be considered only for the courses at
4.20.2 Total number of credits required for obtaining: same level or above.
4.20.2.1 B.Tech. - 170 6.5 Student must provide all details for the course which he is
4.20.2.2 M.Tech. - 75 requesting for credit transfer along with the acceptance letter
4.20.2.3 MCA - 80 for the scrutiny of the concerned DCC.
4.20.3 Minimum CGPA for Graduation is 5.0 and the Maximum that
6.6 Maximum number of credits that can be transferred by a
can be earned is 10.
student shall be limited to 20.
4.21 Audit Courses: 6.7 Student has to get minimum passing grades/marks for such
4.21.1 Students have the option of Auditing additional courses with courses for which credits transfer is to be made.
the consent of the course instructor. 6.8 Credit transfer availed by a student shall be properly recorded
4.21.2 On successful completion, the student will be given 'AP' letter on the academic record9s) of the student.
grade.
4.21.3 The grade obtained in an audit course will not be used for
computation of CGPA. 7. TERMINATION FROM THE PROGRAMME
A student shall be required to leave the institute without the
4.22 Minor Specialization: award of the degree, under the following circumstances.
4.22.1 Students have the choice of getting a minor specialization 7.1 If a student fails to acquire minimum number of credits
along with their degrees by earning 12 credits in the required to get promoted to next higher semester at the end of
prescribed set of subjects offered as electives. academic probation year.
4.22.2 Minor specialization shall be mentioned in the VIII semester
7.2 If a student fails to acquire the requirements for the completion
marks card / Transcript along with CGPA.
of the degree within the maximum permissible period.
7.3 If a student is absent for more than 6 weeks at a stretch in a
5. CHANGE OF BRANCH
semester without sanctioned leave.
5.1 Change of branch is allowed on request against vacancies
before commencement of the third semester based on 7.4 Based on disciplinary action, on recommendation of an
academic performance of first year B.Tech. appropriate committee and approved by the vice chancellor.
5.2 Applications for change of branch shall be submitted to the
Associate Director (Academics), at the end of the second
semester.

08
FIRST YEAR B. TECH. (Common for all branches)
(Applicable to students admitted during 2014 and later)

Physics Group
First Semester Second Semester
Year
Subject Code L T P C Subject Code L T P C
MAT 1101 Engineering Mathematics - I 3 1 0 4 MAT 1201 Engineering Mathematics - II 3 1 0 4
PHY 1001 Engineering Physics 2 1 0 3 CHM 1001 Engineering Chemistry 2 1 0 3
CIE 1001 Mechanics of Solids 2 1 0 3 BIO 1001 Biology for Engineers 2 1 0 3
ECE 1001 Basic Electronics 2 1 0 3 ELE 1001 Basic Electrical Technology 2 1 0 3
1 MME 1001 Basic Mechanical Engineering 2 1 0 3 CSE 1001 Problem Solving Using Computers 2 1 0 3
HUM 1001 Communication skills in English 2 1 0 3 CIE 1002 Environmental Studies 3 0 0 3
PHY 1011 Engineering Physics Lab 0 0 3 1 CHM 1011 Engineering Chemistry Lab 0 0 3 1
MME 1011 Workshop Practice 0 0 3 1 CSE 1011 PSUC Lab 0 0 3 1
MME 1111 Engineering Graphics - I 0 0 3 1 MME 1211 Engineering Graphics - II 0 0 3 1

09
Total 13 6 9 22 Total 14 5 9 22

Chemistry Group
First Semester Second Semester
Year
Subject Code L T P C Subject Code L T P C
MAT 1101 Engineering Mathematics - I 3 1 0 4 MAT 1201 Engineering Mathematics - II 3 1 0 4
CHM 1001 Engineering Chemistry 2 1 0 3 PHY 1001 Engineering Physics 2 1 0 3
BIO 1001 Biology for Engineers 2 1 0 3 CIE 1001 Mechanics of Solids 2 1 0 3
ELE 1001 Basic Electrical Technology 2 1 0 3 ECE 1001 Basic Electronics 2 1 0 3
1 CSE 1001 Problem Solving Using Computers 2 1 0 3 MME 1001 Basic Mechanical Engineering 2 1 0 3
CIE 1002 Environmental Studies 3 0 0 3 HUM 1001 Communication skills in English 2 1 0 3
CHM 1011 Engineering Chemistry Lab 0 0 3 1 PHY 1011 Engineering Physics Lab 0 0 3 1
CSE 1011 PSUC Lab 0 0 3 1 MME 1011 Workshop Practice 0 0 3 1
MME 1111 Engineering Graphics - I 0 0 3 1 MME 1211 Engineering Graphics - II 0 0 3 1
Total 14 5 9 22 Total 13 6 9 22
FIRST/SECOND SEMESTER MAT 1201: ENGINEERING MATHEMATICS - II [3 1 0 4]

MAT 1101: ENGINEERING MATHEMATICS - I [3 1 0 4] Partial Differentiation:


Definition, Euler's theorem on homogeneous functions; Total derivative;
Matrix Algebra
Derivatives of composite & implicit functions; Errors and approximations
Matrices, column and row transformations, Inverse of a matrix, Echelon
Taylor's theorem for functions of two variables; Maxima and Minima;
form and rank of a matrix, System of linear equations: Consistency,
Lagrange's method of undetermined multipliers
Solution by Gauss elimination, Gauss Jordon, Gauss Jacobi and Gauss
Mean Value Theorems and Indeterminate Forms:
Seidel methods, Solution of tri-diagonal systems, Eigen values and
Cauchy's mean value theorem, Taylor's mean value theorem. Taylor's
Eigen vectors: Elementary properties, Computation of largest Eigen
and Maclaurin's expansion of functions; indeterminate forms
value by power method.
Infinite Series:
Linear Algebra
Definitions, convergence and divergence of an infinite series; Tests:
Vector concept to higher dimensions, generalized vector operations,
comparison test, ratio test, Cauchy's root test, Raabe's test, Integral test.
Vector spaces and sub spaces, Linear independence, Linear
Alternating series: Leibnitz's theorem, absolute and conditional
transformations.
convergence; Power series
Inner products, Inner product spaces, Orthogonal projections, Gram-
Analytical solid geometry:
Schmidt process of orthogonalization.
Spheres, Right circular cylinders and Right circular cones
Differential equations and applications
Multiple Integrals:
First order differential equations and applications. Review of solution of
first order differential equations. Higher order differential equations: Double and Triple integrals, Evaluation by the change of order of
Solution of homogeneous and nonhomogeneous linear equations. integration, change of variables, Jacobians. Applications to surface area
Cauchy and Legendre's differential equations; Solution of system of and volumes; Beta and Gamma functions
differential equations Laplace transforms:
Numerical Methods Transforms of elementary functions, Shifting theorems, Transforms of
Interpolation: Finite differences and divided differences. Newton-Gregory periodic functions, Unit step function, Transforms of derivatives. Inverse
and Lagrange's interpolation formulae; Newton's divided difference transforms. Solution of differential equations using Laplace transforms.
interpolation formula; Numerical differentiation; Numerical integration:
Trapezoidal rule, Simpson's one third rule and Simpson's three eighth References:
rule. 1. B. S. Grewal, “Higher Engineering Mathematics”, (42e), Khanna
Solution of Algebraic and Transcendental equations: Bisection method, Publishers, 2013
Method of false position, Iteration method, Newton-Raphson method. 2. N. Piskunov, “Differential Calculus”, Vol I and II, Mir Publications,
Solution of System of Non-linear equations using Newton-Raphson Moscow, 1981
method 3. Rainville E. D. and Bedient P. E. , “A short course in differential
Numerical solution of ordinary differential equations: Taylor's series equations”, (4e), Macmillan Publishers, 1969
method, Euler's method, Modified Euler's method, Runge-Kutta methods 4. Kreyzig E, “Advanced Engineering Mathematics”, (10e), Wiley
and Predicator corrector methods. Eastern , Delhi, 2011
5. Shanti Narayan, “Differential Calculus”, (30e), S Chand & Co ltd,
References: 2005
1. B. S. Grewal, “Higher Engineering Mathematics”, (42e), Khanna
Publishers, 2013 PHY 1001: Engineering Physics [2 1 0 3]
2. Kreyzig E., “Advanced Engineering Mathematics”, (10e), Wiley Optics: Two source interference, Double slit interference, Coherence,
Eastern , 2011 Intensity in double slit interference using phasor method, Interference
3. David C. Lay, “Linear Algebra and applications”, (3e), Pearson from thin films, Newton's rings, Diffraction and wave theory of light,
Education, 2009 Single-slit diffraction, Intensity in single-slit diffraction using phasor
4. Sastry S. S., “Introductory methods of Numerical analysis”, (4e), method, Diffraction at a circular aperture, Double-slit interference
PHI, 2007 and diffraction combined- Intensity in double-slit diffraction
5. Rainville E. D. and Bedient P.E. , “A short course in differential (Qualitative approach), qualitative description of multiple slits and
equations”, (4e), Macmillan Publishers, 1969 diffraction grating
Applied Optics: Spontaneous and stimulated transitions, He-Ne and
Ruby laser, Applications of lasers, Optical fiber, Total internal reflection,
angle of acceptance and numerical aperture, types of optical fiber, types
of attenuation, applications of optical fibers.

10
Quantum Physics: Black body radiation and Planck's hypothesis, BIO 1001: BIOLOGY FOR ENGINEERS [2 1 0 3]
Stefan's Law, Wein's displacement law, Photoelectric effect, Compton Chemistry of life: Elements of life and their bonding ability; Introduction
effect, Photons and electromagnetic waves, Wave properties of to biomolecules: water, phospholipid, Energy storage molecule,
particles, de-Broglie hypothesis, Quantum particle (wave packet, phase carbohydrates, Proteins and their structure, Enzymes, bioenergetics,
speed, group speed). The double-slit experiment revisited, the effect of pH on Biological system, structure of DNA & RNA
uncertainty principle Inheritance in life: Principles of biology; Biological Hierarchies;
Quantum Mechanics: An interpretation of quantum mechanics, Wave Introduction to genetic terms using examples of evolution; Introduction
function and its significance, particle in a box (infinite potential well), to Mendelian Genetics- Experiments and terms; Monohybrid, Dihybrid,
Schrodinger equation, Particle in a well of finite height, Tunneling Test cross, chromosomes, genetic diseases
through a potential barrier and its applications, The quantum model of Molecular basis of inheritance: Transformation experiments; DNA-the
the hydrogen atom, The wave functions for hydrogen hereditary material; DNA replication; problems in replication; RNA,
Solid State Physics: Free electron theory of metals, Band theory of trancription, template, non-template, coding and non-coding,
solids, Electrical conduction in metals, Insulators and Semiconductors, Translation- genetic code, start and stop.
Superconductivity-Properties and Applications Biological Diversity and evolution: Principles of biology, Biological
Hierarchies, Modularity and incremental change, Form and function,
References: Symbiosis, coevolution, communal benefit, commensalism, parasitism;
1. Halliday, Resnick, Krane; “PHYSICS: Volume 2”, (5e), John Wiley & Biological control systems, Bioinspiration and biomimetics
Sons, Inc, 2009 Case studies: Nature's number, origin of life, evolution of hemoglobin,
2. Serway & Jewett; “PHYSICS for Scientists and Engineers with sickle cell anemia, bio nano machine, Photosynthesis, circulation and
Modern Physics”, (9e), Thomson, 2013 gas exchange in Biological system, vaccination, Green revolution:
disease resistant plants, Epigenetics: Examples from Human Population
CHM 1001: ENGINEERING CHEMISTRY [2 1 0 3] biotechnology, Seeking clues in DNA, Antibiotic Resistance
Electrochemistry: Galvanic cell and Electrolytic Cells, Nernst equation,
Energetics of Cell Reactions, Determination of E.M.F., Standard Cell, References:
Weston Cadmium Cell, Calomel Electrode, Glass Electrode, 1. Arthur T Johnson, “Biology for Engineers”, CRC Press, 2010
Concentration Cells 2. J.B. Reece, L.A. Urry, M.L. Cain, S.A. Wasserman, P.V. Minorsky,
Battery Technology: Battery Characteristics, Primary and Secondary R.B. Jackson, Benjamin Cummings, “Campbell-Biology”, (9e),
Batteries, Dry cell, Lithium copper sulfide cell, Lead-acid, Nickel- Pearson Global, 2011
cadmium and Lithium ion batteries, Fuel cells, Alkaline fuel cell, Proton 3. David L Nelson & Michael M Cox, “Lehninger - Principles of
exchange membrane fuel cell and Direct methanol fuel cell Biochemistry”, (5e), W.H. Freeman and Company, New York, 2008
Corrosion and its Control: Classification, Electrochemical theory of 4. Alberts, Johnson, Lewis, Raff, Robert, Walter, “Molecular Biology of
corrosion, Galvanic series, Galvanic, pitting, stress and intergranular the Cell”, (5e), Garland Science Publisher, 2008
corrosion, Factors affecting corrosion, Corrosion prevention methods
Metal Finishing: Polarization, Decomposition potential and overvoltage; CIE 1002: ENVIRONMENTAL STUDIES [3 0 0 3]
Characteristics of a good deposit, Factors influencing the nature of Introduction of the subject: Significance and need, Applications of
deposit, Methods of cleaning the metal surface, Hard chromium and environmental science/engineering in various engineering disciplines,
decorative chromium plating, Electroless plating, Electroless plating of environmental ethics, concept of sustainable development
copper Ecosystem: Meaning, structure and functions, food chain, and food
Chemical Fuels: Classification, Calorific value and its determination web, ecological pyramids, energy flow in an ecosystem, types of
Bomb calorimeter and Boys calorimeter, Coal and its analysis -proximate ecosystems.
and ultimate, Brief account of liquid and gaseous fuels Biodiversity and its conservation: Meaning, factors affecting diversity,
Modern Materials: Fundamental Principles, Different types of chemical threats and conservation strategies
bonds, Chemistry and applications of Polymers, Biomaterials, Glass, Natural Resources: Renewable and non-renewable energy sources
Cement, Ceramics, Composite materials, Liquid crystals, Environmental Pollution: Causes, effects, remedies for water, air, solid
Superconducting materials, Thin films, Nanomaterials waste (land), noise, biomedical, nuclear, marine, nuclear, e-wastes &
overview of water supply and sanitation
References: Global environmental issues: Rain water harvesting, watershed
1. P. C. Jain, M. Jain, “Engineering Chemistry”, (15e), Dhanpat Rai & management, global warming, acid rain, ozone layer depletion- causes,
Sons, Delhi, 2006 effects and remedies, green buildings, Interlinking of rivers
2. C. V. Agarwal, “Chemistry of Engineering Materials”, (9e), BS Disaster Management: Meaning, episodes/case studies, Application of
Publications, Delhi, 2006 GIS, role of IT.

11
Environmental legislations: Salient features of water, air, soil and Hooke's law, modulus of elasticity, tension test on ductile and brittle
environmental protection acts. materials, factor of safety, allowable stress, Stresses and deformations
Term work: A field visit to a local polluted site, study of an ecosystem, in tapering bars, stepped bars, Poisson's ratio, shear stress and shear
audio-visual display of current environmental issues. strain, modulus of rigidity, relation between modulus of elasticity,
modulus of rigidity and bulk modulus., application problems.
References: Statically indeterminate members - Compound bars, thermal stress
1. Benny Joseph, “Environmental studies”, McGraw-Hill Education Stresses in thin cylinder: hoop, longitudinal and shear stresses; Change
(India), 2009 in dimensions due to the fluid pressure, joint efficiency and application
2. R. Rajagopalan, “Environmental studies: From Crisis to Cure”, (2e), problems
Oxford Higher Education, 2011 Shear force and bending moment diagrams: SFD and BMD for
3. P. Venugopal Rao, “Principles of Environmental Science and statically determinate beams
Engineering”, PHI, 2006
4. Erach Bharucha, “Text book of Environmental Studies for References:
undergraduate courses”, Universities Press, Hyderabad, 2010 1. Singer F.L., “Engineering Mechanics”, Harper & Row,1994
5. Gupta Harsh K, “Disaster Management”, Orient Blackswan, 2003 2. Bhavikatti & Rajasekharappa, “Engineering Mechanics”, New Age
International, 2006
HUM 1001: COMMUNICATION SKILLS IN ENGLISH [2 1 0 3] 3. Pytel and Singer, “Strength of Materials”, Harper & Collins, 1987
Oral communication: Speech- presentation /Impromptu speeches, 4. Bhavikatti S.S., “Strength of Materials”, Vikas Publishers, 2005
group discussion, interview techniques, formal / informal 5. Basavarajaiah & Mahadevappa, “Strength of Materials”, CBS
communication Publishers, 2001
Listening Audio: Texts/speeches (Test listening skills factual, evaluative
questions and summary ECE 1001: BASIC ELECTRONICS [3 0 0 3]
Reading: Extracts from texts different genres/ styles Analog Electronics: Diode and its application: I-V Characteristic, Static
Writing: Creative writing assignment, academic writing, formal writing and dynamic Resistance, Half and Full Wave Rectifiers with and without
essay, paragraphs, business correspondence, mechanics of writing filter, Zener regulator, 78xx regulator, Special purpose diodes. BJT and its
punctuation, functional grammar, editing (given text- extract) applications: I-V Characteristics, Cut-off, active and saturation mode of
operation, CB, CC and CE configuration, Transistor Biasing: fixed, voltage
References: divider bias and emitter bias. Transistor as an amplifier: RC coupled
1. Strunk, W and White E. B., “The Elements of Style”, Longman, New Amplifier; Transistor as a Switch: Relay Driver Circuit. Operational
York, 1999 Amplifier and its applications: Basic model, virtual ground concept,
inverting amplifier, non-Inverting Amplifier, adder, subtractor, difference
2. Sorby, S. A. and Bulleit W, “An Engineer's Guide to Technical
amplifier, integrator, differentiator, comparator, Square wave generator.
Communication”, Longman , New York, 2006
Digital Electronics: Number systems and Codes, Boolean Algebra;
3. Raman, Meenakshi and Sharma, S., “Technical Communication:
Logic gates: OR, NOT, AND, NOR, NAND, XOR and XNOR. Concept of
Principles and Practice”, Oxford University Press, India, 2011
Universal Logic; Simplification of Boolean functions using K map; Flip-
4. Jones, D., “Cambridge English Pronouncing Dictionary”, Cambridge
flops: JK flip flop and D-flip flop and simple applications. Introduction to
University Press, 2011
ADC&DAC
Principles of Electronic Communication: Fundamentals of Analog
CIE 1001: MECHANICS OF SOLIDS [2 1 0 3]
communication, Introduction to Digital Communication, Communication
Part-A: Mechanics of Rigid bodies networks, Mobile Communication.
Resultant of coplanar concurrent and non-concurrent force system:
Resolution, composition, moment of force, Varignons theorem, couple,
References:
application problems
1. Albert P Malvino, “David J Bates Electronic Principles”, 7e, TMH,
Equilibrium of Coplanar concurrent and noncurrent force system:
2007
Conditions of equilibrium, Space and free body diagram, Lami's theorem
2. George Kennedy, Bernad Davis, “Electronic Communication
- application problems
Systems”, 4e, TMH, 2004
Support reaction, types of loading, friction - application problems.
3. Robert L. Boylestad, Louis Nashelsky, “Electronic Devices & Circuit
Centroid and Moment of Inertia: Simple and composite areas,
Theory”, 11e, PHI, 2012
application problems
4. Malvino and Leach, “Digital Principles & applications”, 7e, TMH,
Part-B: Mechanics of Deformable bodies
2010
Simple Stresses and Strains: Mechanical properties of materials,

12
ELE 1001: BASIC ELECTRICAL TECHNOLOGY [2 1 0 3] efficiency, and Brake thermal efficiency, Working of simple carburetor,
Electric Circuit Elements: Active and passive elements, Source Types and properties of lubricants, Splash lubrication system.
transformation, Resistors in series, Resistors in parallel, Capacitors in Power Transmission: Definition, Belt drives- open and crossed ,Velocity
series and parallel, Inductor in series and parallel, Transient analysis and ratio, Stepped cone pulley, Fast and loose pulley, Length of belt, Tension
energy stored in inductor and capacitor. in the belt, Slip, Creep (No derivations), Introduction to rope drive and
DC circuit Analysis: Star- delta transformations, Mesh current method, chain drives, Gear Drives-Types of gears, Velocity ratio for Gear trains,
Node voltage method. Simple and compound gear trains, Numericals onbelt and gear drives.
Electromagnetism: Magnetic field due to electric current, Faraday's laws Machine Tools: Lathe - Classification, Block diagram of engine lathe,
of Electromagnetic induction, self and mutual inductance, dot rule. Specification of lathe, List of lathe operations. Drilling - Classification of
Magnetic Circuits: MMF, magnetic field strength, permeability, drilling machines, Block diagram of radial drilling machine, List of drilling
reluctance, series and parallel magnetic circuits. operations.
Single-phase AC Circuits: Average value and rms value of periodic Casting and Forging: Types of moulding sand and its desirable
sinusoidal and non- sinusoidal wave forms, form factor, Phasor properties, Patterns- Single piece and split piece pattern, Pattern
representation. Alternating current in pure resistor, inductor and allowances, Steps in the preparation of two box green sand mould,
capacitor, RL, RC, and RLC series circuits, average power, power factor, Defects in casting, Introduction to forging.
parallel AC circuit, analysis of series parallel circuits, complex power and Welding: Classification, Principle of Resistance spot welding, Electric
power triangle, improvement of power factor. arc welding and oxy-acetylene gas welding, Gas flames, Introduction to
Resonance: Series and parallel resonance, Q factor, half- power soldering and brazing
frequencies, bandwidth Introduction to Engineering Materials: Ferrous and Non-ferrous metals
Three-phase AC Circuits: 3- phase system, phase sequence, star and and its properties, Introduction to heat treatment.
delta connections, relationship between line and phase voltage and
current, analysis of 3-phase circuit with balanced and unbalanced loads, References:
three phase power measurement by two wattmeter method. 1. K. R.Gopalakrishna, "Text book of elements of Mechanical
Electrical Power System: Power system components, Overview of Engineering", Subhash Publications, Bangalore, 2005.
Electrical Machines, Energy measurements. 2. Roy & Choudhury, "Elements of Mechanical Engineering", Media
Promoters & Publishers Pvt. Ltd, Mumbai, 2000.
References: 3. Mishra B.K., "Mechanical Engineering Sciences", Kumar & Kumar
1. Kothari D. P. & Nagarath I. J., “Basic Electrical Technology”, (2e), Publishers (P) Ltd, Bangalore, 1999.
TMH, 2009 4. Trymbaka Murthy S., "A text book of elements of Mechanical
2. Nagasarkar T. K. & Sukhija M. S., “Basic Electrical Engineering”, Engineering", I. K. International Publishing House Pvt. Ltd, 2010.
(2e), OUP, 2011 5. Rajput R. K., "Elements of Mechanical Engineering", Fire Wall Media,
3. Hughes E., “Electrical and Electronic Technology”, (10e), Pearson 2005.
Education, 2010 6. B. S. Raghuwanshi, “A Course in Workshop Technology”, Vol 1,
Dhanpat Rai & Sons, New Delhi, 2005.
MME 1001: BASIC MECHANICAL ENGINEERING [2 1 0 3]
Properties of Steam and Boilers: Steam formation, Types of steam, MME 1111 ENGINEERING GRAPHICS I [0 0 3 1]
Steam properties- Enthalpy, Simple numericals for finding enthalpy and Introduction: Geometrical constructions, Dimensioning and
dryness fraction. Steam Boilers: Classification, Working principle of conventions of lines
Babcock & Wilcox Boiler. Projection of points: Orthographic projection, reference planes,
Prime Movers: Classification of Prime movers, Working principle of Quadrants, Types of quadrants, Conventional representation of first angle
steam, gas and water turbines, Concept of impulse and reaction steam projection system. Projection of points
turbines. Projection of straight lines: Line parallel to both reference planes;
Power plants: Working principle of thermal, nuclear, hydel and solar Perpendicular to reference plane; Inclined to one reference plane;
power plants (Illustration with block diagram only) Inclined to both reference planes including locating traces; finding true
length and inclinations.
Refrigeration: Principle and working of vapour compression
refrigeration system, Desirable properties of an ideal refrigerant, Projection of plane surfaces: Simple planes (Triangle, Square,
Definition of COP, Unit of refrigeration Rectangle, Pentagon, Hexagon &Circle), Plane resting on edge and
corner conditions, Surface inclined to HP & perpendicular to VP, Surface
I.C. Engines: Classification, Working of 2-stroke, 4 - stroke C.I and S.I
inclined to VP and perpendicular to HP, Planes inclined to both HP & VP
Engines with P-V diagrams, Definitions and simple numerical for determining
(Change of position method only).
Indicated Power, Brake Power, Mechanical efficiency, Indicated thermal

13
Projection of solids: Simple solids like prisms &pyramids (Triangle, MME 1011: WORKSHOP PRACTICE [0 0 3 1]
Square, Rectangle, Pentagon &Hexagon), Cone and cylinder, Solids Mechanical Engineering Practices: Sheet Metal work, Plumbing
resting on edge and corner conditions, Axis inclined to HP and parallel to Exercises, Study of Automotive systems like steering mechanism,
VP, Inclined to VP & parallel to HP. axis inclined to both HP and VP (Change Transmission System, Suspension, Demonstration of Spur gear, Helical
of position method only) gear, Belt drives, Chain drives, Couplings, Keys, Bearings , Fasteners,
Gear box, Engine parts, Demonstration on the working of Lathe and
References:
Drilling machine.
1. Gopalkrishna K. R. and Sudhir Gopalkrishna , "A textbook of
Civil Engineering Practices: Tensile test, Shear test and Compression
Computer Aided Engineering Drawing", (37e), Subhas Stores,
test, measure and plot the given area using chain and tape, prismatic
Bangalore, 2012.
compass, plot the profile of a ground using dumpy-level and levelling staff.
2. Bhat N. D. and V.M. Panchal, "Engineering Drawing", (50e), Charotar
Electrical and Electronics Engineering Practices: Demonstration of
Publishing House, Anand, India, 2010
wiring tools, types of wires and wiring systems, Wiring rules, Electrical
3. Venugopal K. "Engineering Drawing and Graphics + Auto CAD” safety and precautions, types of electrical lighting sources. Wiring of
Newage International Publishers, Delhi, 2002 lamp controlled by single switch; Staircase wiring; 3-pin plug socket;
4. Narayana K. L. and Kannaiah P, "Text book on Engineering Drawing" Familiarization of fuses, MCB, ELCB, Study of overload protection with
Scitech Publications, Chennai, 2002 fuses. Wiring of a single-phase energy meter with AEH Load, Wiring of 3-
5. Basant Agrawal& Agrawal C M, “Engineering Drawing”, Tata phase energy meter with lighting load and a 3-phase Induction Motor
McGraw Hill, New Delhi, 2010 with DOL starter
Familiarization of electronic components such as Resistors, Capacitors,
MME 1211: ENGINEERING GRAPHICS II [0 0 3 1] diodes, transistors, and Integrated Circuits, Multimeter and testing of
Introduction: Sectioning the object, Development of surfaces of solids, diodes and transistors, Bread-board assembly, Soldering practice on
Isometric projection, Orthographic projection and its applications PCB; assembling simple electronic gadgets such as digital counter, buzzer
Sections of solids: Horizontal vertical and inclined section planes and with a 555 timer, musical doorbell; Building a DC regulated power supply.
true shape of sections; Drawing sectional views with true shape of
section. Simple cases of solids resting on HP or VP with axis References:
perpendicular to reference planes, inclined to one reference plane. 1. Hajra Choudhury S. K and Bose S .K, “Elements of Workshop
Section plane perpendicular to VP, inclined to HP and inclined to VP. Technology”, Volume I, Media Promoters & Publishers Pvt. Ltd.,
Development of surfaces: Parallel line development for prisms Mumbai, 2012.
(Triangle, Rectangle, Square, Pentagon and Hexagon) and cylinders 2. Raghuvanshi S.S, “Workshop Technology”, Dhanpat Rai and Sons,
(Including simple cut solids), Radial line development for pyramids Delhi, 2002.
(Triangle, Square, Rectangle, Pentagon and Hexagon) and cones 3. Punmia B.C, “Surveying”, Laxmi Publications, Bangalore, 2012
(Including simple cut solids) 4. Bhattacharya S.K and Rastogi K.M, “Experiments in Basic Electrical
Isometric projections and views: Simple & cut solids (Prisms, Engineering”, New Age International, Delhi, 2003
Pyramids, Cones, Cylinders), combined solids, Simple machine 5. Maheshwari L.K and Anand M.M.S, “Laboratory manual for
components Introductory Electronics”, New Age International, Delhi, 2008
Orthographic conversions: Simple & cut solids (Prisms, Pyramids,
Cones, Cylinders), combined solids, Simple machine components. CSE-1001: PROBLEM SOLVING USING COMPUTERS [2 1 0 3]
Computer - Hardware and Software; Memory and its types Input /
References: Output Devices; Problem solving using computer: algorithms and
1. Gopalkrishna K. R. and Sudhir Gopalkrishna, “A textbook of Flowcharts; C++ program structure, character set, identifiers and key
Computer Aided Engineering Drawing”, (37e), Subhas Stores, words, Operators and expressions, Operator precedence and
Bangalore, 2012 associativity, type conversions, arithmetic expressions, evaluation of
2. Bhat N. D. and V.M. Panchal, "Engineering Drawing", (50e), Charotar expressions; Control Structures - Statements and blocks, looping
Publishing House, Anand, India. 2010 constructs, Arrays & Strings 1D array, programs on array manipulation,
3. Venugopal K., “Engineering Drawing and Graphics + Auto CAD”, 2-D arrays, matrix manipulation, strings-operation on strings; Coding
Newage International Publishers, Delhi. 2002 exercises on various numerical analysis algorithms; Structured
4. Narayana K. L. and Kannaiah P, “Text book on Engineering Drawing”, Programming Functions; Structures and Pointers; Introduction to object
Scitech Publications, Chennai, 2002 oriented programing - basic concepts, benefits; File Manipulation - File
5. Basant Agrawal& Agrawal C M, “Engineering Drawing”, Tata handling functions, Introduction to cyber security.
McGraw Hill, New Delhi, 2010

14
References: 3. Wavelength of laser using diffraction grating
1. E. Balaguruswamy, “Object Oriented Programming with C++”, 4. Newton's rings
(6e), Tata McGraw Hill, 2013 5. Fermi energy of metals
2. E.Balaguruswamy, “Computing Concept and Programming in C”, 6. Band gap energy
Tata McGraw Hill, 2008. 7. Determination of Boltzmann constant
3. Delores M. Etter, “Engineering Problem Solving with C”, 2013 8. Hall effect
4. Grewal B.S, “Numerical Methods in Engineering and Science with 9. Black body radiation
Programming in C and C++”, Khanna Publishers, 2010
10. Photo electric effect
5. Sastry S.S, “Introductory methods of Numerical analysis”, (4e), PHI,
11. Resistivity of semiconductors using four probe method
2007.
12. Numerical aperture of optical fiber

CSE 1011: PROBLEM SOLVING USING COMPUTERS LAB [0 0 3 1]


CHM 1011: ENGINEERING CHEMISTRY LABORATORY [0 0 3 1]
Programming using C++: Familiarisation of programming environment;
1. Alkalimetric titration
simple programs; Programs on Branching Control Structures; Looping
2. Total hardness of water
Control Structures; 1-D arrays and its manipulation, searching and
sorting; 2-D arrays, matrix manipulations; Strings string handling 3. Estimation of percentage of copper in brass
functions; Implementation of numerical methods, User defined 4. Estimation of weight of iron in haematite
functions; Pointers and Structures; File Manipulations 5. Estimation of percentage of manganese dioxide in pyrolusite
Introduction to MATLAB: Interactive computations, script files, data 6. Estimation of ammonia nitrogen in a fertilizer
visualization, functions, file I/O and GUI, Introduction to SIMULINK. 7. pK value of a weak acid by potentiometric titration
8. Conductometric acid-base titration
References: 9. Determination of concentration of copper using Colorimer
1. Grewal B.S, “Numerical Methods in Engineering and Science with 10. Determination of coefficient of viscosity of liquid.
Programming in C and C++”, Khanna Publishers, 2010 11. Chloride content of water
2. E. Balaguruswamy, “Object Oriented Programming with C++”, 6 th
12. Analysis of lead pigment
edition, Tata McGraw Hill, 2013
3. Rudrapratap, “Getting Started with MATLAB - A Quick introduction References:
for scientists and engineers”, Oxford University Press 2009. 1. Vogel A.I. “Text book of Quantitative Inorganic Analysis”, (5e), ELBS,
1998
PHY 1011: ENGINEERING PHYSICS LAB [0 0 3 1] 2. “Laboratory Manual for Engineering Chemistry Laboratory”, M.I.T.,
1. Ultrasonic Interferometer 2013
2. Series and parallel resonances

15
B. Tech in MECHANICAL ENGINEERING

THIRD SEMESTER FOURTH SEMESTER

Year
Subject Code Subject Name L T P C Subject Code Subject Name L T P C
MAT 2101 Engineering Mathematics – III 2 1 0 3 MAT 2210 Engineering Mathematics – IV 2 1 0 3
MME 2101 Thermodynamics – I 2 1 0 3 MME 2201 Thermodynamics – II 2 1 0 3
MME 2102 Kinematics of Machinery 3 1 0 4 MME 2202 Fluid Mechanics 3 1 0 4
MME 2103 Strength of Materials 2 1 0 3 MME 2203 Dynamics of Machinery 2 1 0 3
MME 2104 Material Science and Metallurgy 3 0 0 3 MME 2204 Automobile Engineering 3 0 0 3
II MME 2105 Manufacturing Technology 4 0 0 4 *** **** Open Elective – I 3 0 0 3
MME 2116 Computer Aided Mechanical Drawing 0 0 6 2 MME 2217 Mechanical Lab – I 0 0 3 1
MME 2118 Workshop Practice – I 0 0 3 1 MME 2218 Workshop Practice – II 0 0 3 1
MME 2219 Strength of Materials Lab 0 0 3 1
16 4 9 23 15 4 9 22
FIFTH SEMESTER SIXTH SEMESTER
MME 3101 Turbo Machines 3 1 0 4 HUM 4001 Essentials of Management 2 1 0 3

205
MME 3102 Mechanical Design – I 3 1 0 4 MME 3201 Heat Transfer 3 1 0 4
MME 3103 CAD-CAM 3 0 0 3 MME 3202 Mechanical Design – II 3 1 0 4
MME 3104 Metrology and Measurements 3 0 0 3 MME **** Program Elective – III 3 0 0 3
III
MME **** Program Elective – I 3 0 0 3 MME **** Program Elective – IV 3 0 0 3
MME **** Program Elective – II 3 0 0 3 *** **** Open Elective – II 3 0 0 3
MME 3117 Mechanical Lab – II 0 0 3 1 MME 3216 CAD Lab 0 0 6 2
MME 3119 Metrology Lab 0 0 3 1 MME 3217 Fluid Mechanics Lab 0 0 3 1
18 2 6 22 17 3 9 23
SEVENTH SEMESTER EIGHTH SEMESTER
HUM 4002 Engg Economics and Financial Management 2 1 0 3 MME 4297 Seminar 1
MME 4101 Mechanical Vibrations 3 1 0 4 MME 4298 Industrial Training 1
MME 4102 Finite Element Methods 2 1 0 3 MME 4299 Project Work / Practice School 12
MME 4103 Production Planning and Control 2 1 0 3
IV
MME **** Program Elective – V 3 0 0 3
MME **** Program Elective – VI 3 0 0 3
MME 4116 FEM Lab 0 0 6 2
MME 4117 Mechanical Lab – III 0 0 3 1
15 4 9 22 14
Minor Specialisations 10. MME 4022: MEMS and Nano Technology
11. MME 4023: Micro Machining
I. Machine Design 12. MME 4024: Non Destructive Testing
1. MME 4001: Design for Manufacture and Assembly 13. MME 4025: Non-Conventional Energy Sources
2. MME 4002: Design of Mechanical Systems 14. MME 4026: Operations Research
3. MME 4003: Fatigue and Fracture 15. MME 4027: Organizational Behavior
4. MME 4004: Tribology 16. MME 4028: Personnel Management and Industrial Relations
17. MME 4029: Plant Engineering and Maintenance
II. Manufacturing 18. MME 4030: Plant Layout and Material Handling
1. MME 4005: Composite Materials 19. MME 4031: Power Plant Engineering
2. MME 4006: Heat Treatment of Metals and Alloys 20. MME 4032: Project Management
3. MME 4007: Lean Manufacturing 21. MME 4033: Statistical Quality Control
4. MME 4008: Machine Tool Technology 22. MME 4034: Supply Chain and Logistics Management
23. MME 4035: Technology Management
III. Thermal Engineering 24. MME 4036: Theory of Internal Combustion Engines and
1. MME 4009: Computational Fluid Dynamics Emissions
2. MME 4010: Design of Thermal Power Plant Systems 25. MME 4037: Total Quality Management
3. MME 4011: Jet Propulsion and Rocket Technology 26. MME 4038: Work Systems Engineering
4. MME 4012: Refrigeration and Air Conditioning Systems
Open Electives
IV. Business Management 1. MME 3281: Corrosion Engineering
1. HUM 4011: Financial Management 2. MME 3282: Energy Engineering
2. HUM 4012: Human Resource Management 3. MME 3283: Industrial Safety Engineering
3. HUM 4013: Marketing Management 4. MME 3284: Internal Combustion Engines
4. HUM 4014: Operations and Systems Management 5. MME 3285: Introduction to Alternative Fuels and Applications
6. MME 3286: Introduction to Composite Materials
Other Programme Electives 7. MME 3287: Introduction to Nano Technology
1. MME 4013: Alternative Fuels for Engines 8. MME 3288: Introduction to Operations Research
2. MME 4014: Automatic Control Engineering 9. MME 3289: Introduction to Quality Control
3. MME 4015: Corrosion Science and Engineering 10. MME 3290: Introduction to Refrigeration
4. MME 4016: Elements of Mechatronics Systems and Air Conditioning Systems
5. MME 4017: Fluid Drives and Control 11. MME 3291: Introduction to Robotics
6. MME 4018: Friction and Wear 12. MME 3292: Personnel Management and Industrial Relations
7. MME 4019: Industrial Robotics 13. MME 3293: Project Management
8. MME 4020: Introduction to Combustion 14. MME 3294: Thermal Treatment of Metals and Alloys
9. MME 4021: Materials Characterization

206
Classification of cams and followers, Cam profile diagrams of disc cam
THIRD SEMESTER
with knife edge follower, roller follower, flat foot mushroom follower and
roller oscillating follower.
MAT 2101: ENGINEERING MATHEMATICS - III [2 1 0 3]
Gradient, divergence and curl, Line, surface and volume integrals. References:
Green's, divergence and Stoke's theorems. Fourier series of periodic 1. Hamilton H. Mabie, Charles F. Reinholtz, “Mechanisms and
functions. Half range expansions. Harmonic analysis.Fourier integrals. Dynamics of Machinery”, (4e), Wiley's Publication, 1987.
Sine and cosine integrals, Fourier transform, Sine and cosine 2. Ballaney P. L., “Theory of Machines and Mechanism”, Khanna
transforms. Partial differential equation-Basic concepts, solutions of Publications, New-Delhi, 2009.
equations involving derivatives with respect to one variable only. 3. Rattan S. S, “Theory of Machines”, Tata Mc-Graw Hill Publishers Pvt.
Solutions by indicated transformations and separation of variables. One- Ltd, New-Delhi, 2009.
dimensional wave equation, one dimensional heat equation and their
4. Singh V. P., “Theory of Machines”, Dhanpat Rai & Co. (P) Ltd, New-
solutions. Numerical solutions of boundary valued problems, Laplace
Delhi, 2010.
and Poisson equations and heat and wave equations by explicit methods.
5. Rao J.S. and Rao V. Dukkipati, “Mechanism and Machine Theory”,
New Age International Publishers, 2012.
References:
1. Erwin Kreyszig, “Advanced Engineering Mathematics”, (5e), Wiley
MME 2103: STRENGTH OF MATERIALS [2 1 0 3]
Eastern, 1985.
Strength, stiffness and stability stresses, Thermal stress, Elastic
2. Sastry S. S., “Introductory Methods of Numerical Analysis”, (2e),
constants, Strain energy, Stress-strain diagrams, Resilience,
Prentice Hall, 1990.
Toughness, Hardness, Types of beams, Shear force and bending
3. Grewal B. S., “Higher Engineering Mathematics”, Khanna moment in beams, Stresses in beams, Theory of simple bending, Stress
Publishers, 1989. variation along the length and beam section, Shear stresses in beams.
4. Murray R. Spiegel, “ Vector Analysis”, Schaum Publishing Co., 1959 Analysis of torsion of circular bars, Shear stress distribution, Bars of
solid and hollow circular section, Twist and torsion stiffness, Elastic
MME 2101: THERMODYNAMICS - I [2 1 0 3] curve of Neutral axis of the beam under normal loads, Evaluation of beam
Introduction, Basic concept and definitions, Zeroth law of deflection and slope, Columns, Equivalent length of a column, Euler
thermodynamics, concept of temperature, temperature scales. equation, Slenderness ratio, Rankine formula for columns, Biaxial state
Thermodynamic definition of work, heat, comparison between heat and of stresses, Thick &thin cylindrical shells and spherical shells.
work. Application of first law to various engineering processes, steady
flow energy equation and its applications. Limitations of First law, References:
statements of second law and its corollaries, Carnot cycle, Statement of 1. Popov E.P., “Engineering Mechanics of Solids”, Prentice-Hall of
third law, thermodynamic temperature scale. Clausius inequality, India, New Delhi, 1997.
entropy - property, principle of increase of entropy, entropy relations to 2. Beer F. P. and Johnston R, “Mechanics of Materials”, (3e),McGraw-
other thermodynamic properties. Introduction to pure substance, Hill Book Co, 2002.
dryness fraction and its measurement, different processes involving
3. Nash W.A, “Theory and Problems in Strength of Materials”, Schaum
pure substance. Thermodynamic processes involving ideal and real
Outline Series, McGraw-Hill Book Co, New York, 1995.
gases, generalized compressibility chart. Available and unavailable
4. Kazimi S.M.A., “Solid Mechanics”, Tata McGraw-Hill Publishing Co,
energy, maximum work in a reversible processes, second law efficiency.
New Delhi, 1981.
5. Ryder G.H, “Strength of Materials”, (3e), Macmillan India Ltd., 2002.
References:
1. Nag P. K., “Engineering Thermodynamics”, McGraw - Hill Education
MME 2104: MATERIAL SCIENCE AND METALLURGY [3 0 0 3]
India Pvt. Ltd, 2013.
Introduction to crystal structure, crystal defects, Solidification-
2. Yunus A. Cengel and Michael A. Boles, “Thermodynamics: An
homogeneous and heterogeneous nucleation, crystal growth. Phases in
Engineering Approach”, Tata McGraw Hill Education, 2011.
solids - single & multi phase, solid solutions, equilibrium diagrams,
3. Gordon J. Van Wylen and Richard E. Sonntag, “Fundamentals of
Isomorphous and Eutectic systems, equilibrium & non-equilibrium
Classical Thermodynamics”, Wiley, 1986.
cooling, Invariant reactions, Lever rule. Iron-Carbon systems - Allotropy
4. Rogers G. F. C. and Yon Mayhew, “Engineering Thermodynamics: and Polymorphism, cooling curve for pure iron, Fe-C equilibrium
Work and Heat Transfer”, Prentice Hall, 1996. diagrams. Heat treatment processes like Annealing, Normalizing,
5. Gupta S. C., “Thermodynamics”, Pearson Education, 2009. Hardening, Tempering and Case hardening. Ferrous alloys - alloy steels
like plain carbon steels, stainless steels, free machining steels, HSS and
MME 2102: KINEMATICS OF MACHINERY [3 1 0 4] Maraging steels, Cast irons. Non-ferrous alloys - Brasses, Bronzes and
Kinematic chain, mechanism, mobility of mechanism, inversions, Al-Cu alloys.
machine. Kinematic chain with three lower pairs, with four lower pairs,
four bar chain, single slider crank chain, double slider crank chain and References:
their inversions, Drag link mechanism. Velocity and acceleration of 1. Avner S.H., “Introduction to Physical Metallurgy”, (3e), McGraw Hill,
mechanisms by relative velocity method. Instantaneous Centers, Klein's 2004.
construction for slider crank mechanism. Law of gearing, cycloidal and 2. William D. Callister, “Materials Science and Engineering”, John Wiley
involute teeth, involutometry, involute function, interference, efficiency & Sons, 2007.
of helical gears, worm & worm wheel. Simple, compound, reverted and
3. Lakhtin Yu., “Engineering Physical Metallurgy and Heat Treatment”,
epicyclic gear trains. Ratio of tensions, Power transmitted, centrifugal
MIR Publishers, 1985.
tension in a belt. Flat Pivot and Collar friction, Power loss due to friction,
4. Gupta K.M., “Material Science, Metallurgy and Engineering

207
Materials”, Umesh Publication, 2012. 3. Peter Smid, CNC Programming Hand book, Industrial Press, New
5. Raghavan V., “Material Science and Engineering”, (4e), Prentice Hall York, 2000.
of India, 1989.
FOURTH SEMESTER
MME 2105: MANUFACTURING TECHNOLOGY [4 0 0 4]
Foundry technology, moulding materials, moulding sand & testing,
Casting-Investment casting, Permanent mould casting, Slush casting, MAT 2210: ENGINEERING MATHEMATICS - IV [2 1 0 3]
Pressure die casting Centrifugal casting and Continuous casting. Special Functions-Series solutions of Bessel and Legendre differential
Advantages, limitations and applications of different types od welding equations, Recurrence formulae, generating functions and Orthogonal
processes. Cold, warm and hot working of metals. Constructions, properties for Jn(x) and Pn(x).. Probability, finite sample space,
accessories & attachments, types and operations of Lathes, Drilling, conditional probability and independence, Bayes' theorem, one
Milling, Planing, Shaping and grinding machines. Drill bits, milling cutters dimensional random variable: mean and variance, Chebyshev's
and grinding wheels. Principles, working, equipment, advantages, inequality. Two and higher dimensional random variables, covariance,
limitations and applications of different Non-conventional machining correlation coefficient, regression, least square principle of curve
processes. Processing of plastics. fitting.Distributions: binomial, Poisson, uniform, normal, gamma, chi-
square and exponential.Moment generating function, Functions of one
References: dimensional and two dimensional random variables, Sampling theory,
1. Rajput R. K., “A Text book of Manufacturing Technology”, Laxmi Central limit theorem and applications
Publications Private Limited, 2011.
2. Khanna O.P., “A Text book of Production Technology”, Dhanpat Rai References:
Publications, 2011. 1. Kreyzig E., “Advanced Engineering Mathematics”, (7e), Wiley
3. Rao P. N., “Manufacturing Technology”, Tata McGraw-Hill Publishing Eastern, 1999.
Company Limited, New Delhi, 2006. 2. Meyer P. L., “Introduction to Probability and Statistical applications”,
4. Paul DeGarmo E., Black J. T. and Ronald Kohser A., “Materials and (2e), American Publishing Co., 1980.
Process in Manufacturing”, John Wiley and Sons, Delhi, 2004. 3. Hogg and Craig, “Introduction of Mathematical Statistics”, (4e),
5. Benedict G. F., “Non Traditional Machining Techniques”, Marcel MacMillan, 1975.
Decker, New York, 1990. 4. Grewal B. S., “Higher Engineering Mathematics”, Khanna
Publishers, 1989.
MME 2116: COMPUTER AIDED MECHANICAL DRAWING [0 0 6 2]
2D drafting-Intersection of Solids, Threaded Fasteners, square bolts & MME 2201: THERMODYNAMICS - II [2 1 0 3]
nuts, foundation bolt, Bearings, Couplings and Joints. 3D part modeling, Carnot, Auto, Diesel and Dual cycles, Performance testing of IC Engines,
assembly and sectional/exploded views-Drawings-Vertical stuffing box, principle of combustion in SI and CI engines. Vapour power cycles like
Simple eccentric, Drill jig, Square tool post, Non-return valve, Screw Rankine, Reheat, Regenerative and Binary vapour cycles. Reciprocating
jack, Swivel bearing, Strap type connecting rod end and Machine vice. air compressor-multistage compression with perfect and imperfect inter
cooling.Refrigeration cycles-Bell-Coleman cycle, vapour compression
References: and vapour absorption cycle, Properties of refrigerants.Gas turbine
1. Gopalkrishna K. R., “Machine Drawing”, Subhas Publications, cycles with inter cooling, reheating and regeneration.Nozzles and
Bangalore, 2002. Diffusers-Isentropic flow, sonic velocity, Mach number, steam nozzles.
Stoichiometry-analysis of products of combustion from boiler and
2. Bhat N. D., “Machine Drawing”, Charotar Publishing House, Anands,
engine exhaust.
2002.
3. Venugopal K., “Engineering Drawing and Graphics + Auto CAD”,
Newage International Publishers, Delhi, 2002. References:
4. Narayana K. L. and Kannaiah P., “Text book on Engineering Drawing”, 1. Nag P.K., “Basic and Applied Thermodynamics”, Tata McGraw Hill,
Scitech Publications, Chennai, 2002. 2006.
5. Sham Tickoo, “CATIA for Engineers and Designers”, Dreamtech 2. Mayhew A. and Rogers B., “Engineering Thermodynamics”,
Press New Delhi, 2005 Longman Green & Co. Ltd. London. E.L.B.S. Edition, 1990.
3. Yunus A. Cengel and Michael A. Boles, “Thermodynamics: An
Engineering Approach”, Tata McGraw - Hill Education, 2011.
MME 2118: WORKSHOP PRACTICE - I [0 0 3 1]
4. Rolle Kurt C., “Thermodynamics and Heat power”, Pearson
Education, 2005.
Preparation of models using Welding techniques, Lathe and CNC Turning
5. Nijaguna and Samaga, “Thermodynamics data handbook”.
Centre. Acceptance tests on machine tools.

MME 2202: FLUID MECHANICS [3 1 0 4]


References:
Fluid properties, Fluid statics, Intensity of pressure, Pascal's law,
1. Hajra Chaudhury S.K., Hajra Choudhury A. K. and Nirjhar Roy, pressure variation in static fluid, pressure measurement by manometers,
Elements of Workshop Technology, Vol. I, Media Promoters and Hydrostatic forces on surfaces, determination of metacentric height,
Publishers Pvt. Ltd., 2003. Stability of floating and submerged bodies, Continuity equation for one
2. Hajra Chaudhury S.K., Hajra Choudhury A. K. and Nirjhar Roy, and three dimensional flow, fluid velocity and acceleration, Energy
Elements of Workshop Technology, Vol. II, Media Promoters and possessed by fluid, Euler's equation of motion along a stream line,
Publishers Pvt. Ltd., 2003. Rayleigh's method and Buckingham's Pi-theorem, similitude, Fluid flow
measurement devices, Viscous flow-critical Reynolds number, laminar

208
flow through circular pipe, laminar flow between fixed parallel plates, 3. Rajput R. K., “Automobile Engineering”, (1e), LaxmiPublication (P)
Flow through pipes - Darcy and Chezy equation, Flow past immersed Ltd, 2010.
bodies - Lift and drag, skin friction drag and form drag, streamlined body, 4. Narang G. B. S., “Automobile Engineering”, Khanna Publishers,
Bluff body, Boundary layer concept, laminar boundary layer thickness, 1990.
Boundary layer separation. 5. Giri N. K., “ Automotive Technology”, Khanna Publication, 2006.

References: MME 2217: MECHANICAL LAB - I [0 0 3 1]


1. Streeter V. L. and Beinzamin E., “Fluid Mechanics”, Willy Intl., New Determination of viscosity, flash & fire point of oil, lower calorific value of
York,1998. gaseous fuel and dryness fraction of steam. Calibration of pressure
2. Modi P. N. and Seth S. M., “Hydraulics and Fluid Mechanics”, gauge and determination of compression ratio. Performance test on
Standard Book House, 2011. different single cylinder, low/high speed four/two stroke petrol & diesel
3. Kumar K. L., “Engineering Fluid Mechanics”, Eurasia Publishing engines. Performance test on IC engine with computerized testing
House, New Delhi, 2000. facility. Area measurement by Planimeter.
4. Bansal R. K., “Fluid Mechanics and Hydraulic Machines”, Laxmi
Publication, New Delhi, 2006. References:
5. Yunus A. Cengel and John M. Cimbala, “Fluid Mechanics”, Tata 1. Ganeshan V., “Internal Combustion Engines”, (3e), Tata McGraw Hill,
McGraw-Hill Publications, 2006. Education Private Limited New Delhi, 2007.
2. Mathur M. L. and Sharma R. P., “Course in Internal Combustion
MME 2203: DYNAMICS OF MACHINERY [2 1 0 3] Engines”, Dhanpath Raj Publishers, New Delhi, 2001
Static force analysis of Bell Crank Lever, Slider crank mechanisms, Four-
bar mechanism, Drag link Mechanism, Toggle mechanism, Stone MME 2218: WORKSHOP PRACTICE - II [0 0 3 1]
Crusher mechanism, Mechanisms involving gears and Cams, Plate Exercises on spur gear and helical gear cutting using milling & gear
links. Determination of inertia forces on various links of four bar hobbing machines. Practice of shaping operations, Exercises on
mechanism and slider crank mechanism. Determination of flywheel size grinding operations. Machining using CNC Vertical Machining Center
for single cylinder, multi-cylinder IC engine and press work. Balancing of and use of Non-conventional machines.
rotating masses in the same and different planes. Balancing of
reciprocating masses, Balancing of multi-cylinder in-line engines & V- References:
engines. Centrifugal governors such as Porter, Proell, Hartnell and 1. Hajra Chaudhury S.K., Hajra Choudhury A. K. and Nirjhar Roy,
Wilson Hartnell governors. Gyroscopic effect on the movements of an
air-craft, ship and automobiles. Elements of Workshop Technology, Vol. II, Media Promoters and
Publishers Pvt. Ltd., 2003.
References: 2. Peter Smid, CNC Programming Hand book, Industrial Press, New
1. Ballaney P. L., “Theory of Machines and Mechanism”, Khanna
York, 2000.
Publications, New-Delhi, 2009.
2. Rattan S. S, “Theory of Machines”, Tata Mc-Graw Hill Publishers Pvt.
MME 2219: STRENGTH OF MATERIALS LAB [0 0 3 1]
Ltd, NewDelhi, 2009.
Tension test on mild steel, Compression test on cast iron, Hardness
3. Singh V. P., “Theory of Machines”, Dhanpat Rai & Co. (P) Ltd,
tests Rockwell, Brinell, Vicker's, Charpy Impact test& Izod test on mild
NewDelhi, 2010.
steel, Shear test, Torsion test, Fatigue test on mild steel, Test on leaf
4. Robert L. Norton, “Design of Machinery: An Introduction to the
spring, Test on Helical spring, Bending and compression test on wood,
Synthesis and Analysis of Mechanisms and Machines”, McGraw-
Heat treatment of steel and microstructure study of metals.
Hill, 2012.
5. Rao J.S. and Rao V. Dukkipati, “Mechanism and Machine Theory”,
References:
New Age International Publishers Year, 2012.
1. Suryanarayana A.V.K., “Testing of Metallic Materials”, PHI, 1990.
2. Khanna and Justo, “Highway Materials Testing”, Nemchand, 1989.
MME 2204: AUTOMOBILE ENGINEERING [3 0 0 3]
3. Technical Teacher's Training Institute, “Laboratory Manual of
Automotive engine classification, Multi cylinder arrangements, engine
Strength of Materials”, Oxford University Press, 1983.
parts, Valve timing diagram. Fuel supply system-pumps, mixture
strength, carburetor, fuel injector, MPFI system. Ignition system, Cooling 4. Davis H.E., Troxell G.E., Wiscocil C.T., “The Testing and Inspection of
system and Lubrication system. Clutch-single plate, multi plate, Engineering Materials”, McGraw Hill Book Company.
centrifugal and semi centrifugal disc clutch, Fluid flywheel. Gear box-
constant mesh gear box, synchromesh gear box, Epicyclic (automatic)
gear box and torque converter, Overdrive mechanism. Drive to wheels-
FIFTH SEMESTER
torque reaction, driving thrust, braking torque, Universal joint, propeller
shaft, differential gear box and rear axle. Tube and tubeless tyres, MME 3101: TURBO MACHINES [3 1 0 4]
Steering system, Suspension system. Brakes-drum, disc, hydraulic, Classification, Dimensional analysis & similitude of incompressible and
servo and air . compressible flow turbo machines. Energy transfer- Euler turbine
equation, Velocity triangles, physical interpretation of components of
References: energy transfer, degree of reaction, concept of utilization factor for a
1. Heinz Heisler, “Vehicle and Engine Technology”, (2e), Butterworth- turbine, theoretical head capacity relationship for pumps and
Heinemann Publication, 1998. compressors. Thermodynamics of turbomachines-isentropic
2. Kirpal Singh, “Automobile Engineering”, Vol. I & II (12e), Standard efficiencies of turbo machines based on stagnation and static
Publishers Distributors, New Delhi, 2011. conditions, infinitesimal polytropic and finite stage efficiencies for

209
turbines and compressors, preheat factor for a compressor and reheat 2. Ibrahim K Zeid, “CAD/CAM Theory and Practice”, Tata McGraw Hill,
factor for a turbine. Analysis of pumps, blowers, fans and compressor- New Delhi, 1998.
working of radial flow pumps, compressors and blowers, centrifugal 3. Groover Mikell P., “Automation, Production Systems, and Computer
compressors and axial flow compressors and fans. Analysis of hydraulic Integrated Manufacturing”, Prentice Hall of India, New Delhi, 2008.
and steam turbines. 4. Rao P. N., “CAD/CAM”, Tata McGraw Hill Publishing Company Ltd.,
New Delhi, 2005.
References: 5. Radhakrishnan P., “Computer Numerical Control Machines”, New
1. Yahya S.M., “Turbomachines”, Satya Prakashana, New Delhi. Central Book Agency (P) Ltd., Kolkata, 2004.
2. Yahya S.M., “Turbines, Compressors and Flans”, TMH, New Delhi,
2005. MME 3104: METROLOGY AND MEASUREMENTS [3 0 0 3]
3. Shepherd. D.G., “Principle of Turbomachinery”, Macmillan Co. New Static characteristics of instruments and measurement systems.
York, 1956. Methods of pressure measurement by Elastic pressure elements and
4. Sayers.A.T., “Hydraulic & Compressible flow Turbomachines”, McLeod gauge. Methods of temperature measurement by pressure
McGraw Hill, 1990. thermometer, Electrical resistance thermometer, Thermocouples and
5. Dixon S. L, “Fluid Mechanics, Thermodynamics of Pyrometer. Strain measurement on static and rotary shaft, orientation of
Turbomachinery”, Pergamon, 2006. strain gauges, gauge factor, strain gauge bridge circuit, calibration
circuit, temperature compensation. Measurement of force, torque and
MME 3102: MECHANICAL DESIGN - I [3 1 0 4] shaft power. Grades of tolerances, letter symbols for tolerances, types of
Ductile and brittle fracture, strain energy, creep & temperature, Hertz fits. Taylor's principle for design of gauges, Gauge Maker's tolerance,
contact stresses. Principal stresses, theories of failure, factor of safety, types of gauges. Straightness measurement using straight edge and
strength under combined axial, bending & torsional loads, stress using Autocollimator. Squareness measurement, Surface texture
concentration. Stresses in curved beams. S-N diagram, Low and high measurement and measurements of screw threads.
cycle fatigue, variables affecting fatigue strength, Goodman & Soderberg
equations. Design of shafts subjected to bending in two planes in References:
addition to axial loads. Design of square, rectangular & taper keys. 1. Beckwith Thomas G., “Mechanical Measurements”, Pearson
Strength and efficiency of riveted joints, structural joints of lap & butt Education, Delhi, 2003.
types, boiler joints, rivets subjected to eccentric loading. Strength of 2. Jain R.K., “Engineering Metrology”, Khanna Publishers, New Delhi,
welds, welded joints subjected to eccentric loading, welded pressure 1997.
vessels. Design of bolts subjected to dynamic and impact and eccentric 3. Sawhney A.K., “Mechanical Measurement & Instrumentation”,
loading. Stresses in power screw, efficiency of power screw, force & Dhanpat Rai & Co, New Delhi, 2002.
torque requirement in screw jack. 4. Nakra B.C. and Chaudry K.K., Instrumentation, Measurement &
Analysis, Tata McGraw Hill, New Delhi, 2002.
References: 5. Gupta I. C., “Engineering Metrology”, Dhanpat Rai Publications,
1. Bhandari V. B., “Design of Machine Elements”, (2e), Tata McGraw- New Delhi, 1997
Hill PublishingCompany Limited, New Delhi, 2007.
2. Norton R. L., “Machine Design - An Integrated Approach”, (2e), MME 3117: MECHANICAL LAB - II [0 0 3 1]
Prentice Hall Inc. New Jersy, 2004. Performance test on rotary air blower, two stage air compressor,
3. Juvinalle R. C. and Marshek K. M., “Fundamentals of Machine refrigeration plant, air conditioning plant, two cylinder 4 Stroke diesel
Component Design”, (3e), John Wiley and Sons Inc., New York, engine and MPFI engine. Valve timing diagram of IC engine, Morse test on
2000. multi cylinder petrol engine. Determination of the properties of green
4. Shigley J. E. and Mischke C. R., “Mechanical Engineering Design”, sand. Experiments on Gyroscope, Governors and Balancing of rotating
(5e), McGraw Hill Inc., New York, 2004. and reciprocating unbalance. Measurement using strain gauges.
5. Mahadevan K. and Balaveera Reddy K., “Machine Design Data Hand
Book”, (4e), CBS Publishers and distributors, New Delhi, 1987. References:
1. Ganeshan V., “Internal Combustion Engines”,(3e), Tata McGraw Hill
MME 3103: CAD-CAM [3 0 0 3] Education Private Limited, New Delhi, 2007.
Introduction to Computer aided design, need, benefits, applications of 2. Mathur M. L. and Sharma R. P., “Course in Internal Combustion
CAD, Graphics hardware and Graphics displays. Techniques for Eengines”, Dhanpath Raj Publishers, New Delhi, 2001.
geometric modeling, Types and representation of curves, Types and 3. Rattan S. S., “Theory of Machines”, Tata Mc-Graw Hill Publishers
representation of surfaces: Analytic surfaces, Synthetic Types and Pvt. Ltd, New-Delhi, 2009.
representation of solids. Numerical control and CNC programming,
Computer numerical control, CNC part programming, Advanced features MME 3119: METROLOGY LAB [0 0 3 1]
in CNC programming, Adaptive control machining systems. Industrial Study of measuring instruments and gauges, Screw thread
Robotics, Robot anatomy, Physical configurations, Basic robot motions, measurements, Measurement of effective diameter of external screw
Motion systems, Robot programming, End effectors, Work cell design, threads, Use of Comparators, Measurement of gear dimensions, Radius
robotic application. Manufacturing systems CIM, flexible manufacturing and angle measurement, Calibration of Micrometer and Vernier caliper,
and distributed manufacturing. Surface texture and straightness measurement, Use of Profile projector,
Coordinate Measuring Machine and Interferometer.
References:
1. Groover Mikell P. and Emory W. Zimmers, “CAD/CAM: Computer- References:
Aided Design and Manufacturing”, Prentice Hall of India, New Delhi, 1. Jain R. K., “Engineering Metrology”, Khanna Publishers, New Delhi,
2001. 1997.

210
2. Gupta I. C., “Engineering Metrology”, Dhanpat Rai Publications, MME 3202: MECHANICAL DESIGN - II [3 1 0 4]
New Delhi, 1997. Coil springs-helical coil springs, design of springs subjected to steady,
3. Raghavendra N. V. and Krishnamurthy L.. “Engineering Metrology fluctuating and impact loads, critical frequency, concentric springs. Leaf
and Measurements, Oxford University Press, 2013. springs-semi elliptic carriage springs, stress equalization, combination
of leaf & coil springs. Design of spur, helical and bevel gears based on
static, dynamic and wear strength considerations. Design of worm
SIXTH SEMESTER gears. Sliding contact bearings-lubricants, mechanism of film
lubrication, temperature rise, heat generation & dissipation. Selection of
HUM 4001: ESSENTIALS OF MANAGEMENT [2 1 0 3] rolling contact bearings. Selection of V belt, timer belt, rope and chain
drive. Torque capacity and heat dissipation in different mechanical
Definition of management and systems approach, Nature & scope, The
brakes like block brake, band brake and pivoted shoe brake.
functions of managers, Corporate social responsibility. Planning: Types
of plans, Steps in planning, Process of MBO, How to set objectives,
Strategies, Policies & planning premises, Strategic planning process and References:
tools. Nature & purpose of organising, Span of management, factors 1. Bhandari V. B., “Design of Machine Elements”, (2e), Tata McGraw-
determining the span, Basic departmentalization, Line & staff concepts, Hill Publishing Company Limited, New Delhi, 2007.
Functional authority, Art of delegation, Decentralisation of authority. HR 2. Norton R. L., “Machine Design - An Integrated Approach”, (2e),
planning, Recruitment, Development and training.Theories of Prentice Hall Inc. New Jersey, 2004.
motivation, Special motivational techniques. Leadership - leadership 3. Juvinall R. C. and Marshek K. M., “Fundamentals of Machine
behaviour & styles, Managerial grid. Basic Control Process, Critical Component Design”, (3e), John Wiley and Sons, Inc, New York,
Control Points & Standards, Budgets, Non-budgetary control 2000.
devices.Profit & loss control, Control through ROI, Direct, Preventive 4. Shigley J. E. and Mischke C. R., “Mechanical Engineering Design”,
control. Managerial practices in Japan & USA & application of Theory Z. (5e), McGraw Hill Inc, New York, 2004.
The nature & purpose of international business & multinational 5. Mahadevan K. and Balaveera Reddy K., “Machine Design Data Hand
corporations, unified global theory of management. Entrepreneurial Book”, (4e), CBS Publishers and distributors' New Delhi, 1987.
traits, Creativity, Innovation management, Market analysis, Business
plan concepts, Development of financial projections MME 3216: CAD LAB [ 0 0 6 2]
Solid modelling - Sketching, Extrude, cut, hole, chamfer, round, shell, rib,
References: draft, revolve, pattern, sweep, blend; Datums-Plane, axis, points; Swept
1. Koontz D., “Essentials of Management”, Mc Graw Hill, New York, blend, variable section sweep, helical sweep; Assembly Drawing-Views,
2004. dimensioning, tolerances. Basics of MATLAB.
2. Peter Drucker, “Management, Task and Responsibility”, Allied
Publishers, 2006. References:
3. Peter Drucker, “The practice of management”, Butterworth Hein 1. Ibrahim K Zeid, “CAD/CAM Theory and Practice”, Tata McGraw Hill,
Mann, 2003. New Delhi, 1998.
2. Sham Tickoo, “Pro/Engineer Wildfire for Designers”, CADCIM
MME 3201: HEAT TRANSFER [3 1 0 4] Technologies, 2008.
Modes of heat transfer, governing laws and its derivatives, thermal 3. Rudra Pratap, “Getting Started with MATLAB”, Oxford University
resistance and conductance, overall heat transfer coefficient, initial and Press, 2006.
boundary conditions. Heat conduction through plane and composite
walls, cylinder and composite cylinders, sphere and composite spheres, MME 3217: FLUID MECHANICS LAB [0 0 3 1]
system with uniform rate of internal heat generation, effect of variable Measurement of flow using Venturimeter and Orifice meter. Calibration of
thermal conductivity. Fin analysis, effectiveness and efficiency. Lumped V notch, rectangular notch and orifice. Measurement of force due to
parameter analysis, time constant and response of temperature impact of jet on vanes, determination of friction factor of pipes.
measuring instruments. Application of dimensional analysis to free and Performance test on hydraulic ram, centrifugal pump, reciprocating
forced convection. Boiling regimes, correlations for boiling, film and pump, gear pump, impulse turbine and impulse- reaction turbine.
dropwise condensation, Nusselt theory. Parallel and counter flow heat
exchanger, heat transfer in evaporators and condensers. Thermal
References:
radiation, absorption, reflection & transmission of radiation, radiation
laws, radiation intensity and total emissive power. 1. Jagadishlal, “Fluid Mechanics & Hydraulic Machines”, Metropolitan
Book Co. Pvt. Ltd New Delhi,1995.
2. Bansal R K., “Fluid Mechanics and Hydraulic Machines”, Laxmi
References:
Publication, New Delhi, 2006.
1. Holman J. P., “Heat Transfer”, (10e), Tata McGraw Hill, 2011.
2. Ozisik M.N., “Heat Transfer: A Basic Approach”, (2e), McGraw Hill,
1985. SEVENTH SEMESTER
3. Yunus A. Cenzel and Afshin J. Ghajar, “Heat and Mass transfer”,
(4e), Tata McGraw Hill, 2013.
4. Thirumaleshwar M., “Fundamentals of Heat and Mass Transfer”, HUM 4002: ENGG ECONOMICS AND FINANCIAL
(1e), Pearson Education, 2006. MANAGEMENT [2 1 0 3]
5. Rajput R.K. “Heat and Mass Transfer”, (4e),S Chand Publishing, Nature and significance, Micro & macro differences, Law of demand and
2008. supply, Elasticity & equilibrium of demand & supply. Time value of
money, Interest factors for discrete compounding, Nominal & effective
interest rates, Present and future worth of single, Uniform gradient cash

211
flow. Bases for comparison of alternatives, Present worth amount, application of structural, thermal & flow problems. Finite element
Capitalized equivalent amount, Annual equivalent amount, Future worth formulation by iso-parametric approach, Finite Element Formulation by
amount, Capital recovery with return, Rate of return method, Incremental the Weighted residual method, Application of the Finite element method
approach for economic analysis of alternatives, Replacement analysis. to structural dynamics.
Break even analysis for single product and multi product firms, Break
even analysis for evaluation of investment alternatives. Physical &
References:
functional depreciation, Straight line depreciation, Declining balance
method of depreciation, Sum-of-the-years digits method of depreciation, 1. Daryl L. Logan, “A First course in Finite Element Method”, (4e),
Sinking fund and service output methods, Costing and its types Job Thompson Ltd, India, 2007.
costing and Process costing, Introduction to balance sheet and profit & 2. David V. Hutton, “Fundamentals of Finite Element Analysis”, Tata
loss statement. Ratio analysis - Financial ratios such as liquidity ratios, McGraw Hill. India, 2005.
Leverage ratios, Turn over ratios, and profitability ratios 3. Chandrupatla T. R. and Belegundu A. D., “Introduction to Finite
Elements in Engineering”, Pearson Education, New York, 2001.
References: 4. Reddy J. N., “An Introduction to Finite Element Method”, (3e),
1. Blank Leland and T. Tarquin Anthony J., “Engineering Economy”, McGraw Hill International Edition, New York, 2006.
McGraw Hill, New Delhi, 2002. 5. Larry J. Segerlind, “Applied Finite Element Analysis”, (2e), John
2. Chan S. Park, “Contemporary Engineering Economics”, Pearson Wiley, New York, 1984.
Education Inc., 2010.
3. Raman B.S., “Advanced accountancy”, United Publications, MME 4103: PRODUCTION PLANNING AND CONTROL [2 1 0 3]
Bangalore, 1993. Introduction to production, planning & control, functions, types of
4. Ramachandran T., “Accounting and Financial Management”, production activities. Forecasting- importance and techniques, forecast
Scitech Publications Pvt. Ltd. India., 2001. control. Aggregate Planning- pure and mixed strategies using trial & error
5. Thuesen G. J. and Thuesen H. G., “Engineering Economics”, approach. Job shop scheduling- index method & sequencing
Prentice Hall of India, New Delhi, 2005. techniques. Inventory Control- introduction, classification, inventory
control models, quantity discount concept, reorder level, ABC analysis.
MRP- introduction and MRP processing logic. Assembly line balancing-
MME 4101: MECHANICAL VIBRATIONS [3 1 0 4]
meaning and techniques. Plant Location- factors affecting and methods
Limits of vibration severity, Natural frequency by Newton's Classical of plant location. Plant Layout- types, factors affecting and techniques of
method &Energy method, Longitudinal, lateral & torsional vibration. plant layout.
Viscous damping - different types of viscous damping, Coulomb
damping. Steady state forced vibration subjected to harmonic excitation,
References:
rotating and reciprocating unbalance, force and displacement
transmissibility and whirling of shafts. Vibration measurement- 1. Monks Joseph G., “Operations Management”, Tata McGraw-Hill
transducers, vibrometer, accelerometer, frequency measuring Publishing Co. Ltd., New Delhi, 2004.
instruments, exciters, Machine condition monitoring using vibration 2. Krajewski Lee J. and Ritzman Larry P, “Operations Management”,
signals. Two degree of freedom system-Classical method and Pearson Education (Singapore) Pte. Ltd., Delhi, 2005.
Lagrange's generalized method, Dynamic vibration absorber, Centrifugal 3. Adam Everett E. Jr. and Ebert Ronald J., “Production and Operations
pendulum absorber. Multi degree freedom system-Classical method, Management”, Prentice Hall of India Pvt. Ltd., New Delhi, 2002.
Influence coefficient method, Matrix iteration method, Rayleigh's 4. Chase Richard B., Aquilano Nicholas J. and Jacobs F. Roberts,
method, Dunkerley's method and Holzer's method. Vibration of “Production and Operations Management”, Tata McGraw-Hill
continuous system. Publishing Co. Ltd., New Delhi, 1999.
5. EilonSamuel, “Elements of Production Planning and Control”,
References: Universal Publishing Corporation, Mumbai, 1991.
1. Singiresu Rao S., “Mechanical Vibration”, Pearson Education, New
Delhi, 2004. MME 4116: FEM LAB [0 0 6 2]
2. Graham Kelly S., “Fundamentals of Mechanical Vibrations”, Finite Element Analysis-Truss analysis, Beam analysis, 2D and 3D
McGraw-Hill, Singapore, 1993. structural analysis, Thermal analysis, Shell analysis, Modal and
3. Graham Kelly S., “Schaum's Outline of Mechanical Vibrations Harmonic analysis and Fluid analysis. MATLAB Programming for truss,
(Schaum's Outline Series)”, McGraw-Hill Publication,1996. 2D beams, plane stress and strain problems.
4. Ramamurthi V., “Mechanical Vibration”, Practice with basic theory,
Narosa Publishing House. New Delhi, 2000. References:
5. Rao J. S. and Gupta K., “Introductory Course on Theory and Practice 1. Daryl L. Logan, “A First Course in Finite Element Method”, (4e),
of Mechanical Vibrations”, Wiley Eastern Ltd, 1984 Thompson Ltd. India, 2007.
2. ANSYS Classic/Workbench Software Manual.
MME 4102: FINITE ELEMENT METHODS [2 1 0 3] 3. Rudra Pratap, “Getting Started with MATLAB”, Oxford University
Review of matrix algebra, Basics of theory of elasticity, Basics concepts Press, 2006.
of the Finite element method-discretization, types of elements, degrees
of freedom, displacement models, convergence, displacement MME 4117: MECHANICAL LAB - III [0 0 3 1]
polynomial, Pascal's triangle, higher order elements, Lagrange & Heat transfer from in forced convection and free convection, through
Serendipity polynomials, sub-parametric, super-parametric &iso- composite wall and cylinders. Thermal conductivity of insulating powder
parametric elements, local and global coordinate systems, shape and different metals, Study of parallel flow, counter flow and shell & tube
functions, Finite element formulation by Direct stiffness method- heat exchanger, Calibration of thermocouples, Determination of Stephen

212
Boltzman constant and emissivity. Vibration experiments- Compound automatic assembly and robot assembly, case studies on DFMA,
pendulum, Bifilar suspension, Torsional vibration, Viscous damping, importance of Fits, tolerance and surface finish in design, production
Forced vibration, Transmissibility ratio, Transverse vibration of beam and drawings.
Whirling of shaft.
References:
References: 1. Geoffrey Boothroyd, Peter Dewhurst and Winston A. Knight,
1. Holman J. P., “Heat Transfer”, (10e), Tata McGraw Hill, 2011. “Product Design for Manufacture and Assembly”, CRC Press, 2011.
2. Yunus A. Cenzel and Afshin J. Ghajar, “Heat and Mass Transfer”, 2. James G. Brala, “Design for Manufacturability Handbook”, McGraw
(4e), Tata McGraw Hill, 2013. Hill, New York, 1999.
3. Singiresu S. Rao, “Mechanical Vibrations”, Pearson Education 3. Kevin Otto and Kristin Wood, “Product Design”, Pearson Education,
(Singapore) Pte. Ltd., Delhi, 2004. Delhi, 2001.
4. Ramamurti V. “Mechanical Vibration Practice with Basic Theory”, 4. Chitale A. K. and Gupta R. C., “Product Design and Manufacturing”,
Narosa Publishing House, New Delhi, 2000. Prentice Hall of India Pvt. Ltd., New Delhi, 2005.
5. George E. Dieter, “Engineering Design”, McGraw Hill Book
Co.,Singapore, 2000.
EIGHTH SEMESTER
MME 4002: DESIGN OF MECHANICAL SYSTEMS [3 0 0 3]
MME 4297: SEMINAR Mechanical design process, design factors, design of mechanical
Each student has to present a seminar individually, on any technical systems - Flange coupling, Screw jack, Piston, Connecting rod,
topic of current interest / latest advancement / topics not covered in Crankshaft-Overhung & Center type, Valve gear mechanism, Single plate
the syllabus. clutch, Passenger lift, Concrete mixer, Automobile chassis &
The topic has to be approved by the Department and a report of the suspension. Johnson's method of optimization. Design for manufacture
same has to be submitted a week before the day of the presentation. of cast, forged, turned, milled, drilled and ground parts, design for heat
treatment, design for assembly.
MME 4298: INDUSTRIAL TRAINING
Each student has to undergo industrial training for a minimum period References:
of 4 weeks. This may be taken in a phased manner during the 1. Bhandari V.B., “Design of Machine Elements”, (3e), Tata McGraw
vacation starting from the end of third semester. Hill Publishing Company, New Delhi, 2010.
Student has to submit to the department a training report in the 2. Trikha S. N., “Machine Design Exercises”, Khanna Publishers, Delhi,
prescribed format and also make a presentation of the same. The 2001.
report should include the certificates issued by the industry. 3. Patil S. P., “Mechanical System Design”, Jaico Publishing House,
Mumbai, 2004.
MME 4299: PROJECT WORK / PRACTICE SCHOOL 4. George E. Dieter, “Engineering Design”, McGraw Hill Book Co.,
The project work may be carried out in the institution/industry/ Singapore, 2000.
research laboratory or any other competent institutions. 5. Mahadevan K. and Balaveera Reddy K., “Machine Design Data Hand
The duration of the project work shall be a minimum of 16 weeks Book”, (4e), CBS Publishers and distributors, New Delhi, 1987.
which may be extended up to 24 weeks.
A mid-semester evaluation of the project work shall be done after MME 4003: FATIGUE AND FRACTURE [3 0 0 3]
about 8 weeks. Structure and deformation of materials, fatigue design philosophies,
An interim project report on the progress of the work shall be fatigue mechanisms and microscopic features, macro aspects of fatigue
submitted to the department during the mid-semester evaluation. of metals. High cycle fatigue - stress-life (S-N) curves, general S-N
The final evaluation and viva-voice will be conducted after behavior, fatigue limits, mean stress effects on S-N behavior, factors
submission of the final project report in the prescribed form. influencing S-N behavior, life estimation using S-N approach, concepts
Student has to make a presentation on the work carried out, before of cumulative damage and life prediction. Low cycle fatigue, cyclic
the department committee as part of project evaluation. stress-strain curve determination, fatigue crack initiation in ductile
solids, cyclic deformation and crack initiation in brittle solids. Strain-life
MINOR SPECIALISATIONS approach, notch strain analysis and the strain-life approach. Linear
Elastic Fracture Mechanics, Griffith's analysis, stress and displacement
I. MACHINE DESIGN field, stress intensity factor(SIF), Plane strain fracture toughness. Fatigue
Fracture Mechanics, Crack closure and Fatigue threshold, Effect of over
load on fatigue crack growth.
MME 4001: DESIGN FOR MANUFACTURE AND ASSEMBLY [3 0 0 3]
Essential factors of product design, morphology of design, producibility
References:
requirements in design, DFMA-History, advantages of DFMA in product
design, selection of materials and processes. Sand casting-design rules 1. Dowling N. E, “Mechanical Behavior of Materials”, (4e), Pearson
for sand castings, Investment casting-design guidelines. Characteristics Education, 2012
of the forging process, design guidelines, Design guidelines for turning, 2. Suresh S., “Fatigue of Materials”, (2e), Cambridge University Press,
drilling, reaming, shaping, slotting, milling, grinding, and design 1998
guidelines for heat treatment. Design for die-casting. Design for sheet 3. Stephens R. I., Fatemi A., Stephens R. R. and Fuchs H. O., “Metal
metal working, Design for injection molding, Design for powder metal Fatigue in Engineering”, (2e), John Wiley & Sons, 2000
processing, assembly methods, importance of DFA, basic DFA 4. Bannantine J. A., Comer J. J. and Handrock J. L., “Fundamentals of
guidelines, product design for manual assembly, design for high-speed Metal Fatigue Analysis”, Prentice Hall, 1990

213
5. Prashant Kumar, “Elements of Fracture Mechanics”, McGraw Hill hardening. Age hardening and Thermo-mechanical treatments for
Education, 2009 Aluminium and Non-Ferrous alloys, Ausforming, Isoforming, Thermo-
mechanical annealing Steel specification, Classification and Application
MME 4004: TRIBOLOGY [3 0 0 3] of steels and Cast iron with heat treatments, commercial steel, stainless
Introduction to tribology, History of tribology, Interdisciplinary Approach, steel, maraging steel, Malleabilization. Heat treatment and Application of
Economic Benefits. Importance of Lubrication, Types & Properties of non-ferrous metals and alloys defects, causes and remedies in heat
Lubricants, Lubricants Additives, Boundary Lubrication, Mixed treatment.
Lubrication. Equation of Continuity & Motion, Generalized Reynolds
Equation with Compressible & Incompressible Lubricant, Hydrodynamic References:
& Hydrostatic lubrication, Elastohydrodynamic lubrication. Causes of 1. Rajan T. V., Sharma C P and Sharma Alok, “Heat treatment
Friction, Adhesion Theory, Abrasive Theory, Junction Growth Theory, principles and techniques”, PHI Publication, 1999.
Laws of Rolling Friction, Friction Instability. Wear Mechanisms and Wear 2. Bolton W., “Engineering Materials Technology”, Heinmann
Analysis. Surface engineering, Rolling Contact Bearings, Gears, Journal Newness, 2001.
Bearings - Finite Bearings, Condition Monitoring. Surface topography 3. Thelning K.E.,”Steel and its Heat Treatment”, Butterworth/
measurements, electron microscope and friction and wear Heinemann, 2000.
measurements laser method, bearing performance measurements, 4. Romesh C Sharma, “Principles of Heat Treatment of Steels”, New
bearing vibration measurement. Age International (P) Limited, 1996.
5. Singh Vijendra, “Heat Treatment of Metals”, Standard Publishers
References: Distributors, 2012.
1. Cameron A., “Basic Lubrication Theory”, Ellis Horwood Ltd,
Chichester, 1983. MME 4007: LEAN MANUFACTURING [3 0 0 3]
2. Majumdar B.C., “Introduction to Tribology of Bearings”, A. H. Framework of Toyota Production System, Introduction to Value Stream
Wheeler & Co. Pvt. Ltd., Allahabad, 1999. Mapping, Characteristics of lean value stream. Introduction to Kanban,
3. Williams J.A., “Engineering Tribology”, Cambridge University Press, Kanban Team Formation, Data Collection, Determining the Kanban Size,
UK, 2005. Supplier Kanban, Finished Goods Kanban, EOQ vs Kanban Quantity,
4. Neale, M.J., “Tribology Hand Book”, Butterworth Heinemann, Production Smoothing, Shortening Production Lead Time, Multifunction
London, 1995. Workers, Shortening Setup Time Concepts And Techniques,
5. Stachowiak G. N., Batchelor A. W. and Stachowick G. B., Organization Structure for Promoting Setup Time Reduction,
“Experimental Methods in Tribology”, Tribology Series 44, Editor D Standardization of Operations, Yo-i-Don System, One Shot Setup,
Dowson, 2004. Determining The Standard Quantity of Work In Progress, Preparing The
Standard Operation Sheet.
II. MANUFACTURING
References:
MME 4005: COMPOSITE MATERIALS [3 0 0 3] 1. Monden Y, “Toyota Production System: An Integrated Approach to
Introduction: Definition, classification, types of matrices & Just-In-Time”, (4e), CRC Press, 2011
reinforcements, characteristics &selection. Micro mechanical analysis 2. Rother M and Shook J, “Learning to See: Value Stream Mapping to
of a lamina: Introduction, derivation of stress, strain, modulus of add Value and Eliminate Muda”, The Lean Enterprise Institute, 1999
elasticity of fiber reinforced composites. Manufacturing of polymer 3. Gross J M and McInnis K R, “Kanban Made Simple: Demystifying
composites: Description of method, advantages, disadvantages and and Applying Toyota's Legendary Manufacturing Process”,
application. Metal matrix composites and ceramic matrix composites: AMACOM books, 2003
reinforcement, matrix materials, base metal characteristics & selection, 4. Feld W M, “Lean Manufacturing: Tools, Techniques and How to Use
manufacturing and applications. Design issues and structural Them”, CRC Press, 2001.
component design process. Application developments in aircrafts, 5. Dailey K W, Wieckhorst D and Welch B, “The Lean Manufacturing
missiles, space, automobile, electrical and electronics, marine, Pocket Handbook”, DW Publishing, 2003
recreational and sports equipment's and construction.
MME 4008: MACHINE TOOL TECHNOLOGY [3 0 0 3]
References: Working and Auxiliary motions in machine Tools, Parameters defining
1. Mein Schwartz, “Composite Materials Handbook”, McGraw Hill working motions of a machine tool, Machine tool drives-individual drive,
Book Company, 1984. Group drive, Mechanical Drives for providing rotational movements
2. Autar K. Kaw, “Mechanics of Composite Materials”, CRC Press, ,Selection of range of spindle speeds, Typical layouts for intermediate
2010. spindle speeds, Construction of speed diagram, Layout of speeds in GP,
3. Mallik P. C., “Fiber Reinforced Composites”, Marcel Decker, 1993. Saw diagram of a GP series, Rules for layout of speed boxes having
4. Rober M. Joness, “Mechanics of Composite Materials”, McGraw sliding clusters, Flow Diagram, Ray diagram, Types of Feed Gear Boxes,
Hill Kogakusha Ltd, 2008. Functions and Requirements of machine tool structures, Profiles,
5. Michael W, Hyer, “Stress Analysis of Fiber Reinforced Composite Factors affecting stiffness of machine tool structures & Methods of
Materials”, McGraw Hill International, 1998. improving it, Commonly used bed and column sections, Antifriction
guide ways, Protecting devices, Spindles, Milling & Drilling machines,
MME 4006: HEAT TREATMENT OF METALS AND ALLOYS [3 0 0 3] Antifriction bearings, Elimination of vibration, Machine tool chatter,
Introduction to Iron-Carbon equilibrium diagram & Fundamentals of heat Vibration isolated tool holders.
treatment, decomposition of austenite, TTT diagram, Conventional case
and Surface hardening treatments, factors affecting hardening, laser

214
References: 3. Sarit Kumar Das, Balakrishan A R, “Process Heat Transfer”, Alpha
1. Mehta N K, “Machine Tool Design & Numerical control”, Tata Science International, 2005.
McGraw Hill Publishing Co. Ltd., New Delhi, 2012.
2. Sen and Bhattacharya, “Principles of Machine Tools”, New Central MME 4011: JET PROPULSION AND ROCKET TECHNOLOGY [3 0 0 3]
Book Agency, Calcutta, 2001. Jet Propulsion, Thrust equation, Efficiencies: Ram efficiency, thermal
3. CMTI., “Machine Tool Design Handbook”, Tata McGraw Hill efficiency, propulsive efficiency, propeller efficiency. Propulsive
Publishing Co. Ltd., New Delhi, 2004. Devices: turbo jet, turbo prop engine, turbo shaft engine, Ram jet, pulse
4. Basu S K, “Design of Machine Tools”, Oxford & IBH, Delhi, 1989. jet, Rocket Propulsion, Principle of rocket propulsion, thrust equation,
5. George Schlesinger, “Testing Machine Tools”, Pergamon Press, Criteria for Rocket-Motor Performance- specific impulse, total impulse,
Oxford, 1982. Chemical Rockets: Solid propellant rockets, types of solid propellant,
burning rate, solid propellant grain configurations. Liquid propellant
III. THERMAL ENGINEERING rockets, Feed systems and injectors. Gaseous propellant rockets,
Developments in Rocket Technology: nuclear propulsion systems,
Electrical propulsion and Hybrid rockets. .
MME 4009: COMPUTATIONAL FLUID DYNAMICS [3 0 0 3]
Models of fluid flow: Continuity, Momentum and Energy equations in
Cartesian coordinate system, General characteristic of the governing References:
equations: The initial and boundary conditions, The format of the 1. Zucrow, “Aircraft and Missile Propulsion”, Vol I and II, John Wiley,
differential equation for the conservation: Discretization Process, New York. 1958.
Methods of deriving the discretized equations, Explicit Taylor series 2. Jain J K, “Gas Turbine Theory and Jet Propulsion”, (7e), Khanna
expansion, Application of the explicit finite difference technique to one Publishers. New Delhi, 1972.
dimensional steady state heat transfer in a rectangular fin, Unsteady 3. Mathur M L and R P Sharma, “Gas Turbines and Jet Propulsion”,
conduction heat transfer: Explicit, Implicit and Crank Nicholson Standard Publishers Distributors, Delhi, 2000.
Methods, Discretization using control volume technique: The Four basic 4. Yahya S M, “Fundamentals of compressible flow with aircraft and
rules in control volume formulation, Discretization of source terms and rocket propulsion”, New Age International Pvt.Ltd. New Delhi, 2004.
linearization, The SIMPLE algorithms to solve flow problems: Staggered 5. Ganesan V, “Gas Turbines”, Tata McGraw-Hill, New Delhi. 2005.
Grid, the derivation of the pressure correction equation as Poisson's
Pressure equation, Implementation of boundary conditions in CFD. MME 4012: REFRIGERATION AND AIR
CONDITIONING SYSTEMS [3 0 0 3]
References: Basic concepts and Air Refrigeration Cycles, Vapor Compression
1. John D Anderson Jr., “Computational Fluid Dynamics - The Basics Refrigeration Systems, Vapor Absorption Refrigeration Systems,
with Applications”, International Edition. McGraw Hill. New York, Compound vapour compression refrigeration system. Multi-evaporator
1995. and cascade systems, Classification of Refrigerants, Comparison of
2. Suhas V Patankar, “Numerical Heat Transfer and Fluid Flow”, thermodynamic properties of refrigerants, Alternate Cooling Methods:
Hemisphere / McGraw Hill, New York, 1980. Desiccant Cooing System, Solar Refrigeration, Thermo Electric
3. Versteeg H K and Malalasekera W, “An Introduction to Refrigeration, Analysis of Steam Jet Ejector Cycle, Refrigeration,
Computational Fluid Dynamics - The Finite Volume Method”, Psychrometry, Psychrometric charts, Process involving Air-Vapour
Longman Scientific & Technical. England, 1995. Mixtures, Air Conditioning Systems, Types of Air Conditioners, Load
4. Ghoshdastidhar, “Computer Simulation of Flow and Heat Transfer”, Estimation for inside and outside design conditions. Different types of
Tata- McGraw-Hill Book Company. New Delhi, 1998. heat loads.
5. Muralidhar K and Sundararajan T, Computational Fluid Flow and
Heat Transfer, Narosa Publishing House, New Delhi, 2003. References:
1. Arora S.C. and Domkundwar S., “Course in Refrigeration and Air-
MME 4010: DESIGN OF THERMAL POWER PLANT conditioning”, Danpath Rai. New Delhi, 1992
SYSTEMS [3 0 0 3] 2. Cook Norman, Refrigeration and Air conditioning, Macmillan
Design of Double Pipe Heat Exchanger, Shell and Tube Heat Exchanger London, 1995
Recuperative Air Pre Heater, Economizer, Boiler furnace design, 3. Stoecker W.F., “Refrigeration and Air conditioning”, Tata McGraw
Estimation of inside heat transfer coefficient using Jens & Lottes Hill,1978
equation and Thom's correlation. Estimation of pressure drop in two 4. Prasad Manohar, “Refrigeration and Air conditioning”, New Age
phase flow using Thom's method, Super heater and Re-heater Design: International Pvt. Limited. New Delhi, 2004
Estimation of flow in each element of a tube assembly. Estimation of 5. Gauger D. C., Shapiro H. N., Pate M. B., “Alternative Technologies for
attenuation factor and direct radiation from furnace, Design of Steam Refrigeration and Air Conditioning Applications”, Springfield,
Condenser-estimation of tube side velocity, surface area and pressure Washigton DC, 2008
drop for various tube sizes & Plot the graph) and estimation of shell
diameter of steam condenser, Design of Cooling Tower. IV. BUSINESS MANAGEMENT

References: HUM 4011: FINANCIAL MANAGEMENT [2 1 0 3]


1. Kern D.Q., “Process Heat Transfer”, McGraw-Hill Publications, Introduction to financial management, Principle of accountancy,
1965. Sources of long term finance, Valuation of securities, Leverages,
2. Ganapathy V., “Applied Heat Transfer”, Penn Well Publishing Working capital management, Capital budgeting, Cost of capital, Cash
Company, Tulsa, Oklahoma, 1982. management, and Dividend decisions.

215
References: References:
1. Prasanna Chandra, “Fundamentals of Financial Management”, Tata 1. Monks Joseph G, “Operations Management”, Tata McGraw-Hill
McGraw Hill, Delhi, 2006. Publishing Co. Ltd., New Delhi, 2004.
2. Pandey I M, “Financial Management”, Vikas Publishing house, Delhi, 2. Krajewski Lee J. and Ritzman Larry P, “Operations Management”,
2007. Pearson Education (Singapore) Pte. Ltd., Delhi, 2005.
3. Subir Kumar Banerjee, “Financial Management”, Sultan Chand & 3. Mieghem J, “Operations Strategy: Principles and Practices,
Co., Delhi,1999. Dynamic Ideas”, ISBN: 0-9759146-6-9, 2008.
4. ICFAI, “Corporate Financial Management”, ICFAI, Hyderabad, 2003. 4. Sterman J D, “Business Dynamics - Systems Thinking and
Modeling for A Complex World”, McGraw Hill, International Edition,
5. Maheshwari S.N, “Financial Management”, Sultan Chand & Co.,
2004.
Delhi, 2002.
5. Senge Peter, “The Fifth Discipline, Currency Doubleday”, New York,
1990.
HUM 4012: HUMAN RESOURCE MANAGEMENT [2 1 0 3]
Evolution and development, HRD Organization and responsibilities.
OTHER PROGRAM ELECTIVES
Evolution of HRM, Theories of HRM. Human resource planning, Human
Resources Inventory, Forecast, Job analysis, Job description, Job
specification, Job evaluation, Employment stability. Human Resource MME 4013: ALTERNATIVE FUELS FOR ENGINES [3 0 0 3]
Planning and Recruiting, Induction, & socialization, Training and Introduction to alternative fuels, Need for alternative fuels - Availability of
development, Performance management and appraisal. different alternative fuels for SI and CI engines. Properties of potential
alternative fuels, Liquid Fuels for SI Engines, Requirements of fuels for SI
References: engines-Different Techniques of utilizing alternative liquid fuels Blends,
Neat form, Reformed fuels - Manufacturing, Storage and Safety-
1. Rao T V and Pereira D F, “Recent experiences in Human Resources
Performance and emission characteristics of alternative liquid fuels,
Development”, Oxford and IBH Publishing,1986.
Liquid Fuels in CI Engines, Requirements of fuels for CI engines- Different
2. Subba Rao A, “Essentials of Human Resource Management and
techniques for their utilization- Blends, Fuel modifications to suit CI
industrial Relations”, Himalaya Publishing House, 1999.
engines, Dual fuelling, Ignition accelerators and other additives, Gaseous
3. Nair N. G. and Latha Nair, “Personnel Management and Industrial Fuels in SI Engines, Gaseous Fuels in CI Engines, Electrical Vehicles.
Relations”, S. Chand Company, 1999.
4. Virmani B R; Rao Kala, “Economic restructuring technology transfer
References:
and human resource development”, Response books,1997.
1. Ramadhas A S, “Alternative Fuels for Transportation”, CRC Press,
5. Pareek Udai et al, “Human Resource Development in Asia: Trends and
Taylor & Francis Group, 2010.
Challenges”, Oxford and IBH Publishing, 2002.
2. Thipse S S, “Alternative Fuels: Concepts, Technologies and
Developments”, Jaico Book Distributors, 2010.
HUM 4013: MARKETING MANAGEMENT [2 1 0 3]
3. Gajendra Babu M K, “Alternative Transportation Fuels: Utilization in
Understanding marketing management, Assessing market opportunities Combustion Engines”, CRC Press, Taylor & Francis Group, 2010.
and customer value, Adapting marketing to the New Economy, Building
4. Michael F. Hordeski, “Alternative Fuels: The Future of Hydrogen”,
Customer Satisfaction, Value, and Retention, Market Demand, Scanning
The Fairmont Press, 2008.
the Marketing Environment, Consumer Markets, Business Markets,
5. James D. Halderman, “Hybrid and Alternative Fuel Vehicles”, (2e),
Dealing with the Competition, Market Segments, Product Life Cycle, New
Prentice Hall, 2010.
Market Offerings, Designing and Managing Services, Price Strategies,
Retailing, Wholesaling, Integrated Marketing Communications.
MME 4014: AUTOMATIC CONTROL ENGINEERING [3 0 0 3]
References: The course Automatic control engineering mainly deals with the
application of automatic control in various systems like temperature
1. Philip Kotler, “Marketing Management Analysis, Planning,
control system, water level control system, flow control system etc.
Implementation and Control”, Prentice Hall of India Private Limited,
These physical systems can mathematically modelled and many
New Delhi, 2000.
physically different systems have the same mathematical model. The
2. ICFAI, “Marketing Management”, ICFAI, Hyderabad, 2003.
advantage of such mathematical models is that these can be solved
3. Varshney R L and Gupta S L, “Marketing Management”, Sultan easily and system stability can be ascertained using mathematical
Chand & Sons, New Delhi, 2004. models. In addition, the selection of proper system parameters for
4. Adrian Palmer, “Principles of Marketing”, Oxford University Press, safety of a control system can be demonstrated through various plots
New York, 2000. like Nyquist and Bode plots. Digital control systems play a very
important role in handling multi variate systems which can be modelled
HUM 4014: OPERATIONS AND SYSTEMS MANAGEMENT [2 1 0 3] using state space representation.
Types of production activities, Production consumption cycle, Functions
of production and operations management, Importance and uses of References:
forecasting, Product development and design: Product life cycle, Process 1. Harrison H. L. and Bollinger J.G., “Automatic controls”, (2e),
design, Process charts, Flow diagrams and Man machine charts, International Text Book Co. U.S.A, 1968.
Capacity planning, Aggregate planning, Scheduling, Operations strategy, 2. Raven,” Automatic Control Engineering”, McGraw Hill, U.S.A,
Operation performance Frontier and productivity, Systems thinking, 1995.
Systems engineering and its management, Systems decision process.
3. Benjamin Kuo.C., “Automatic Control Systems EEE”, (7e), Prentice
Systems thinking, structure, classification, boundaries, visibility, System
Hall of India Ltd. New Delhi, 1995.
life cycle models, System dynamics and its importance in system
4. Verma S. N., “Automatic Control Systems”, Khanna Publishers,
thinking. System dynamics modeling process.
Delhi, 1990.

216
5. Katsuhiko Ogata, “Modern Control Engineering”, Prentice Hall of circuits, control of multiple actuators, structure of electro pneumatics
India Ltd., New Delhi, 2004. circuits, types of sensors, electrically actuated direction control valves,
relay control systems. Design of electro pneumatic circuits, basic
MME 4015: CORROSION SCIENCE AND ENGINEERING [3 0 0 3] concepts of PLC. Structure of hydraulic circuit, Pascal's law, force
transmission in hydraulics, power pack and accessories, hydraulic
Definitions, Corrosive Environments, Consequences of Corrosion, Cost
fluids, filters, hydraulic pumps and actuators. Calculation of force,
of Corrosion, Corrosion Science and Corrosion Engineering,
speed, power developed. Pipes and fittings, accumulators, construction
Fundamental aspects of Corrosion. Corrosion Cell, Cathodic and Anodic
and working of direction, pressure and flow control valves, proportional
Reactions, Types of Corrosion Cells, Reference Electrode, Calomel
and Servo valves. Applications in regenerative meter in, meter out, bleed
Electrode, Pourbaix Diagrams. Corrosion Rate Expressions, Electro-
off, sequencing, pressure reducing circuits, electro hydraulic circuits.
Chemical nature of Aqueous Corrosion, Polarization, Factors influencing
Corrosion Rate. Types of Corrosion, Measuring Polarization, Anodic
Polarization, Cathodic Polarization, Activation Polarization and References:
Concentration Polarization. Corrosion Prevention, Materials Selection, 1. Peter Croser and Frank Ebel, “Pneumatics Basic Level TP 101”,
Alteration of Environments, Design, Cathodic and Anodic Protection, Festo Didactic GMBH & Co, Germany, 2002.
Corrosion Inhibitors, Coatings. Methods used to determine Corrosion 2. Prede G. and Scholz D., “Electropneumatics Basic Level”, Festo
Rate, Weight Loss Measurements, Linear Polarization, Tafel Extrapolation Didactic GMBH & Co, Germany, 2002.
Techniques. 3. Hasebrink J. P. and Kobler R., “Fundamentals of Pneumatic Control
Engineering”, Festo Didactic GMBH & Co, Germany, 2002.
References: 4. Peter Rohner, “Industrial Hydraulic Control”, John Wiley & Sons,
1. Ahmed Zaki, “Principles of corrosion Engineering and corrosion Brisbane, 1989.
control”, Elsevier science and technology Books, 2006. 5. Majumdar S. R., “Oil Hydraulic Systems Principles and
2. Mars G. Fontana, “Corrosion Engineering”, (3e), Tata McGraw Hill, Maintenance”, Tata McGraw Hill, New Delhi, 2005.
2008.
3. Trethewey K. R. and Longman J. Chamberlain, “Corrosion for MME 4018: FRICTION AND WEAR [3 0 0 3]
Students of Science and Engineering”, Scientific and Technical, Influence of material properties, rolling friction, Measurement of friction,
1988. friction coefficient values. Mechanism of adhesive wear, shapes of
4. Schweitzer A Philip, “Fundamentals of corrosion-Mechanisms, transferred and loose wear particles, size distribution of wear
Causes and preventive methods”, CRC Press, Tayler and Francis fragments, quantitative laws of adhesive wear, wear coefficients,
Group, 2010. Abrasive wear, Corrosive wear, Impact wear, Hydrodynamic,
5. Uhlig H. H. and Revie R. W., “Corrosion and Corrosion Control”, hydrostatic and elasto-hydrodynamic lubrication, solid film lubrication,
Wiley, 1985. boundary lubrication single penetration and multiple penetration
models. Effectiveness of liquid lubricant and solid lubricant. Rebuilding
MME 4016: ELEMENTS OF MECHATRONICS SYSTEMS [3 0 0 3] and surfacing cements, wear tiles, electro spark deposition coatings,
fused carbide cloth, thermal/chemical deposited ceramic coatings,
Introduction: Definition, basic concepts and elements of mechatronic
centrifugal cast wear coatings, wear sleeves, wear plates.
systems, needs and benefits of mechatronics in manufacturing,
Sensors, Transducers: Displacement. Piezoelectric actuators, Shape
memory alloys. Hydraulic & Pneumatic devices Power supplies, valves, References:
cylinder sequencing. Data acquisition and translation: Signal 1. Rabinowicz E, “Friction and Wear of Materials”, John Wiley & Sons,
conditioning Operational amplifiers, inverting amplifier, differential Inc., 1995.
amplifier, Protection, comparator, filters, Multiplexer, Pulse width 2. Bharat Bhushan, “Principles and applications of Tribology”, John
Modulation Counters, decoders, ADC, DAC Signal Analysis - Wiley & Sons Inc., 1999.
Linearization of data, Compensation, Signal Averaging, Fourier analysis. 3. Arnell R D, Davies P B, Halling J &Whomes T L, “Tribology:
Data presentation system: Display - Cathode ray oscilloscope, LED, LCD, Principles and design applications”, Macmillan Education Ltd,
Printers, Magnetic Recording, Controllers and Algorithms: 1991.
Microprocessor Applications. 4. Kragelsky I V, “Friction Wear Lubrication Tribology hand book”, vol
1, 2 & 3, MIR Publishers, 1981.
References: 5. Majumdar B. C., “Tribology of Bearings”, Wheeler Publisher, 1990.
1. Alciatore David G & Histand Michael B, “Introduction to
Mechatronics and Measurement systems”, Tata McGraw Hill, 2003. MME 4019: INDUSTRIAL ROBOTICS [3 0 0 3]
2. Boltan W, “Mechatronics”, Addison Wesley Longman Ltd, 1999. Definition of Robots; Types of Robots; Robot Configuration; Selection of
3. Devdas Shetty & Richard Kolk, “Mechatronics System Design”, Robots; factor affecting the control resolution, Spatial resolution,
PWS Publishing, 2001 Accuracy and repeatability, Specification of a robot, Robot
4. Dan Nesculescu, “Mechatronics”, Pearson Education Pvt. Ltd, arm/manipulator Kinematics, Types of Grippers; Force Analysis of
2002. gripper mechanism; Classification of Actuators; Actuators used in
5. Bradley D A and others, “Mechatronics”, Nelson Thornes Chennai, Robots - DC motors, Stepper motors, AC motors and Servo motors,
2004. Robot Transmission Systems; Sensors; Types and classification of
robot sensors, Positional potentiometer, Velocity tachometer, Working
MME 4017: FLUID DRIVES AND CONTROL [3 0 0 3] of resolver, Optical encoder, Magneto resistive skin, Hall generator,
Electro-magnetic & Adhesive end effectors, proximity sensors; Tactile
Structure and signal flow of pneumatic system, basic components,
Sensing; Robot Vision.
pneumatic actuators: direction and flow control valves, symbols of
pneumatic valves, traverse time diagram. Design of manually operated

217
References: assembled monolayers, Experimental techniques- Temperature
1. Janakiraman P. A., “Robotics and Image Processing”, Tata McGraw measurement techniques, Atomic Force Microscopy, Scanning
Hill, 1995. Tunneling Microscopy, Spectroscopy and Diffraction techniques. Micro
2. Groover M.P., “Industrial Robotics”, PHI, 2008. Electro Mechanical Systems, MEMS, Micro and Nanoscale Thermal
3. JainK.C., Aggarwal L.N, “Robotics Principles and Practice”, Khanna Engineering, Nanofluids preparation and Characterization, Properties of
Publishers, 1997. nanofluids, Nanomaterials used in energy and Environmental
4. Fu, Gonzalez and Lee, “Robotics: Control, Sensing, Vision and applications and their Properties. Device applications in hydrogen
Intelligence”, Tata McGrawHill, 2008. storage and Production, Fuel cells, Battery, Solar energy conversion,
5. Hegde Ganesh S, “A textbook on Industrial Robotics”, Laxmi Waste water treatment, Pollution remedies, Nanomaterials in
Publications (P) Ltd, 2006. automobiles. Challenges and Scope.

MME 4020: INTRODUCTION TO COMBUSTION [3 0 0 3] References:


Introduction to combustion deals with the history of combustion modes, 1. Charles P Poole, “Introduction to Nanotechnology”, Wiley-
flames, types of fuels and their properties. The thermo-chemistry of Interscience Publication, 2003.
combustion, property relations, first law of thermodynamics, reactants 2. Guozhong Cao, “Nanostructures & Nanomaterials”, Imperial
and product mixtures, stoichiometry. Adiabatic flame temperature, College Press, 2004.
chemical equilibrium, the products of combustion. Basics of mass 3. Sobhan C B, “Microscale and Nanoscale Heat Transfer”, Taylor and
transfer related law and species conservation. The fundamentals of Francis Publication, 2008.
Chemical kinetics, important chemical mechanisms and Simplified 4. Mohamed Gad-el-Hak, “The MEMS Handbook”, Taylor and Francis
conservation equations for reacting flows, laminar premixed flames, flame Publication, 2005.
velocity thickness of flame, flame stabilization Laminar diffusion flames 5. James J Allen, “MEMS Design”, Taylor and Francis Publication,
and turbulent flames. Droplet evaporation and burning, applications and 2005.
simple models of droplet evaporation burning. The impact on environment
due to combustion, emissions from combustion processes. MME 4023: MICRO MACHINING [3 0 0 3]
Micromachining, Traditional Micromachining Processes, Materials for
References: micromachining, Advanced Micromachining and Nanofinishing,
1. Stephen R. Turns, “An Introduction to Combustion, Concepts and Abrasive Water Jet Micromachining (AWJMM), Ultrasonic
Applications”, (2e), McGraw- Hill, 2000. Micromachining (USMM), Abrasive Jet Micromachining (AJMM),
2. Mishra D.P., “Fundamentals of Combustion”, PHI Learning Private Thermoelectric Advanced Micromachining, Electric Discharge
Limited New Delhi, 2010. Micromachining (EDM), Electric Discharge Grinding (EDG) And Electric
3. Sharma, S.P. and Mohan, C., “Fuels and Combustion”, Tata McGraw- Discharge Diamond Grinding (EDDG), Wire Electric Discharge
Hill, 1987. Micromachining, Laser Beam Micromachining, Electron Beam
4. Sarkar. S., “Fuels and Combustion”, Orient Longman, 2005. Micromachining. Electrochemical and Chemical Advanced Machining,
5. Mukunda H.S., “Understanding of Combustion”, McMillan India Ltd, Chemical Micromachining (ChMM). Wafer bonding- Anodic bonding,
New Delhi 1989. Fusion bonding, CVD and PVD processes, Spin coating, Evaporation
and Epitaxy, Laser ablation technique. Bulk and Surface
Micromachining Techniques, Micromachining Tools.
MME 4021: MATERIALS CHARACTERIZATION [3 0 0 3]
Basic physical and mechanical properties of materials, X-ray Diffraction
References:
Methods, X-ray Radiation, Generation of X-rays, Distortions of Diffraction
Spectra, Wide Angle X-ray Diffraction and Scattering, Microscopic material 1. Jain V. K., “Introduction to Micromachining”, Narosa
characterization, Light Microscopy - Optical Principles, Image Formation, Publishers,New Delhi, 2010.
Resolution, Depth of Field, Aberrations, Instrumentation, illumination 2. Jain V. K., “Advanced Machining Processes”, Allied Publishers
system. Confocal microscopy, Scanning Electron Microscopy. Contrast Private Limited, New Delhi, 2009.
formation, electron specimen Interactions, preparation for micro- 3. Mojtaba Kahrizi, “Micromachining Techniques for Fabrication of
composition examination, Transmission Electron Microscopy, Selected Area Micro and Nano Structures”, Intech, 2012
Diffraction Characteristics, Single-Crystal Diffraction, Multi-Crystal
Diffraction, Kikuchi Lines. Images of Crystal Defects, Wedge Fringe, Bending MME 4024: NON DESTRUCTIVE TESTING [3 0 0 3]
Contours, Dislocations. Differential Thermal Analysis and Differential NDE in Design, Maintenance and Service, Benefits of NDE, Choosing
Scanning Calorimetry, Thermogravimetry, interpretation of TG curves. the NDE technique, Qualifications of NDE personnel, Penetrant
Inspections, penetrant testing materials and processes, penetrant
References: testing methods and systems, sensitivity, standards, Magnetic Particle
1. Yang Leng, “Materials Characterization: Introduction to Microscopic Testing, Ultrasonic Testing, Elastic wave propagation, Ultrasonic
and Spectroscopic Methods”, John Wiley & Sons (Asia) Pvt. Ltd, Transducers, Criteria for probe selection, Inspection techniques,
Singapore, 2008. ultrasonic techniques for stress measurement and material studies,
2. Sam Zhang, Lin Li, Ashok Kumar, “Materials Characterization Radiographic Techniques, electromagnetic radiation sources,
Techniques”, CRC Press, 2008. properties of X- and gamma rays. Radiographic imaging, Radiographic
inspection techniques, radiographic inspection systems, Eddy Current
Testing (ECT), 3D or phased array ECT. Acoustic Emission Testing,
MME 4022: MEMS AND NANO TECHNOLOGY [3 0 0 3]
Thermography, impact echo method of testing, phased array
General methods of preparation of nanoparticles, Carbon nanostructures
techniques, laser testing methods, vibration testing and analysis
and their Applications. Nanosized Structures, Physical chemistry of
methods.
nanosystems, Nanoparticles, Nanowires and Nanorods, Thin films- Self

218
References:
MME 4027: ORGANIZATIONAL BEHAVIOR [3 0 0 3]
1. Don E Bray and Roderic K Stanley, “Nondestructive Evaluation: A Tool
in Design, Manufacturing and Service”, Taylor and Francis Group, Contributing disciplines to OB, Basic OB Model. Learning, Methods of
London, 1997. shaping behavior, Values, Attitudes and Job satisfaction, Personality,
Determinants of Personality, Personality theories, Major personality
2. Paul E Mix, “Introduction to Nondestructive Testing-A training
attributes, Perception Attribution Theory, Selective perception, Halo
Guide”, (2e), John Wiley and Sons, Inc, 2005.
effect, Contrast effect, Stereo-typing. Maslow's hierarchy of needs,
3. Davis Joseph R., “ASM Handbook: Volume 17, Nondestructive
Theory X and Theory Y, Frederick Herzberg's Motivation and Hygiene
Evaluation and Quality Control”, ASM International Materials Park,
Theory, Contemporary Theories, Group Dynamics, Group Behaviour
OH.
Model, Quality of a good leader, types and theories of leadership.
4. ASNT (Edited), “Materials and Processes for NDT Technology”, Conflict, Dimensions of Conflict Handling Intentions, Virtual
ASNT, USA, 1981. Organisation, Boundary less Organisation, Mechanistic and Organic
5. Ensminger Dale, “Ultrasonics: Fundamentals, Technology, Model, Factors influencing organisation structure. Work Design,
Application”, (2e), Marcel Dekker, New York, 1988. Organisational Change and Organisational Development, Lewin's
Three-Step Model and Action research. Organisational Development.
MME 4025: NON - CONVENTIONAL ENERGY SOURCES [3 0 0 3]
Forms of energy, Energy sources, Need for renewable energy sources, References:
Thermal applications of solar energy, Measurement of solar radiation, 1. Luthans Fred, “Organisational Behaviour”, McGraw Hill, New York,
Empirical equations for predicting the availability of solar radiation, solar 1989.
radiations on tilted surface, flat plate collector, Performance analysis, 2. Gupta Rakesh, “Organisational Behaviour”, Kitab Mahal,Allahabad,
Transmissivity of cover systems, Transmissivity - absorptivity product, 1998.
Collector efficiency factor and Heat removal factor, Principles of wind power,
3. Davis Keith and Newstrom J.W., “Organisational Behaviour at
Total power, maximum power (Betz theory), Actual power, Types of windmill,
Work”, Tata-McGraw Hill, New Delhi, 1997.
Ocean energy, Tidal energy, Tidal energy conversion by single pool system and
4. Moorhead Greogery and Griffin Ricky W., “Organisational
two pool system, Principle of OTEC, Small scale Hydel Plant, Geothermal
Behaviour”, AITBS, New Delhi, 1999.
energy conversion, Biomass energy, Influencing factors for the generation of
biogas, Types of biogas plants, Direct energy conversion,Thermo- ionic 5. Carrel Michaell R., Fundamentals of “Organisational Behaviour”,
converters, MHD generators, Types of MHD converters. Prentice Hall, New Jersey, 1997.

References: MME 4028: PERSONNEL MANAGEMENT AND INDUSTRIAL


RELATIONS [3 0 0 3]
1. Sukatme S. P., “Solar Energy Principles of Thermal Collection and
Storage”, Tata Mc Graw Hill, 2005. Objectives of personnel management, Functions of Personnel
Management, Process of Human Resource Planning, Steps in
2. El-Wakil M M, “Power plant Technology”, McGraw Hill International,
recruitment process, Sources of recruitment, methods of
1984.
recruitment.Promotions, Demotions, Transfers, Separation,
3. Rai G. D., “Non-conventional Energy Sources”, Khanna Publications,
Absenteeism and Turn over, Wage and Salary administration,
1997.
Performance Appraisal, Methods of Performance evaluation.Industrial
4. Rao S and Dr. Parulekar B. B., “Energy Technology”, Khanna Relations: Functional Requirements, Employees participation in
Publishers, 2004. management.Grievances and Grievance Handling, Act of Indiscipline/
5. Culp A. W., “Principles of Energy Conversion”, McGraw Hill Misconduct,Principles for maintenance of discipline.Industrial
International, 2001. Disputes, Procedure forthe Settlement of Disputes, Government and
Industrial Relations, Organs of IndustrialPeace. Trade Unions:
MME 4026: OPERATIONS RESEARCH [3 0 0 3] Objectives and Functions, Growth of Trade Union Movement, Factors
The subject covers definition, phases, applications, advantages and Affecting Growth of Trade Unions, Essentials of a Successful Trade
disadvantages of operations research. Linear programming problems Union.
(LPP) are formulated and solved using graphical and simplex methods
and post optimality analysis conducted. The special cases of LPP include References:
transportation and assignment problems along with travelling salesman 1. Mamoria,C.B., “Personnel Management”, Himalaya Publishing
problem. Game theory and various methods, waiting line models and House, 2007
simulation. Poisson arrival rate and Exponential service times, System 2. Megginson,Leon C, “Personnel and Human Resource
characteristics, Problems on the models- (M/M/1): (M/M/1) : (N/FIFO), Administration”, 1977
Simulation of queuing models, Network model analysis using Critical Path
3. Beach,D.S., “Personnel: The Management of People At Work”,
Method (CPM) and Project Evaluation & Review Technique
1977.
(PERT).Determination of probability/expectation of project completion.
4. Yoder and Dale, “Personnel Management and Industrial Relations”,
1972.
References:
1. Taha H. A., “Operations Research”, (7e), Pearson Education, 2002.
MME 4029: PLANT ENGINEERING AND MAINTENANCE [3 0 0 3]
2. Winston W.L., “Operations Research’, Thomson Asia, 2003.
Introduction to Industrial Building, Building maintenance and repairs,
3. Vohra N. D., “Quantitative Techniques in Management”, 2007. Hardener/sealers, Floor paints, Functions of coating, Constituents of
4. Sharma S. D., “Operations Research”, (14e),KedarNathRamnath paint, Ventilation systems and control, Requirement of water, Building
Publications, 2005. services, Water purification processes, Membrane processes,
5. Kanthi Swaroop, Gupta P K and Manmohan, “Operations Research’, Effluents. Measurement of noise, Vibration, Noise and Vibration control,
Sultan Chand and Sons, 2003. Nature of dust and fumes, Legislation on air pollution concern to the

219
plant engineer. Challenges in maintenance, Responsibilities of the Co. Ltd, 2008.
maintenance department, Reliability centered maintenance, Total 3. Nagpal G R, “Power Plant Engineering’, Khanna Publishers, 2008.
productive maintenance, Planning of maintenance function, Estimation 4. Skrotzki and Vopat, ‘Power Station Engineering Economy’, McGraw
of maintenance work, Maintenance control, Maintenance scheduling, Hill Book Co.
Maintenance cost, Maintenance budgeting and cost control. Condition 5. Wrangham D.A., “Theory and Practice of Heat Engines”, ELBS
Monitoring, Condition monitoring levels, Techniques of condition Edition.
monitoring, Future scope of condition monitoring.
MME 4032: PROJECT MANAGEMENT [3 0 0 3]
References:
Concept of project, Project life cycle, organizing projects within the
1. Mobley K. R., “Plant Engineer's Handbook”, Butterworth- functional organization, organizing projects as dedicated teams,
Heinemann, Woburn, 2001. organizing projects within a matrix arrangement, Project manager and
2. Snow A. D., “Plant Engineer's Reference Book”, Butterworth- their attributes.Feasibility study, Pre-feasibility study, Steps of feasibility
Heinemann, Woburn, 2000. study. Estimating project times and costs, Factors influencing the quality
3. Mobley, Higgins and Wikoff, “Maintenance Engineering Handbook”, of estimates, Top-down approaches of estimation, Bottom-up
McGraw-Hill, 2008. approaches of estimation, Hybrid approach of estimation. Risk
4. Mishra and Pathak, “Maintenance Engineering and Management”, management process, Risk Assessment - probability analysis,
PHI Learning Pvt. Ltd., 2012. Contingency planning, Contingency funding and time buffers, Risk
5. Jyoti Mehrotra, “Principles and Practice of Total Productive response control, Project scheduling, Bar charts and Milestone charts,
Maintenance”, Allied Publishers Ltd., 1998. Development of networks, Work Breakdown Structure, Program
Evaluation and Review Technique, Project audit and closure, Audit
MME 4030: PLANT LAYOUT AND MATERIAL HANDLING [3 0 0 3] reporting, Evaluation of project team and members.
Principle of plant layout, product, process and combination layout,
economics of different types of layout. Factors influencing the layout- References:
manpower, movement, service, material, machinery, waiting, building 1. Gray C., Larson E. and Desai G., “Project Management The
and change factors, location of storages & delay point. Layout planning- Managerial Process”, Tata McGraw Hill Pvt. Ltd., New Delhi, 2013.
scientific approach, flow process chart, cross chart, string diagram, line 2. Paneerselvam R. and Senthilkumar P., “Project Management”, PHI
balancing, templates evaluation of layout, installation of layout, Learning Pvt. Ltd., New Delhi, 2010.
computerized layout planning. Material handling- principles of material 3. Chandra P., “Projects Planning, Analysis, Selection, Financing,
handling, factors in selection of material handling equipment, safety in Implementation and Review”, Tata McGraw Hill Pvt. Ltd., New
material handling, types of material handling equipment, modern Delhi, 2009.
material handling equipment. 4. Choudhry S., “Project Management”, Tata McGraw Hill Publishing
Co. Ltd. New Delhi., 1997.
References: 5. Punmia B. and Khandelwal K., “Project Planning and Control with
1. Buffa E. S. and Rakesh S. K., “Modern Production and Operation PERT and CPM”, Laxmi Publications Pvt. Ltd., New Delhi, 2006.
Management”, John Wiley & Sons, New York, 2003.
2. Richard M., “Practical Plant Layout”, McGraw-Hill, New York, 1955. MME 4033: STATISTICAL QUALITY CONTROL [3 0 0 3]
3. James Apple M., “Plant Layout and Material Handling”, John Wiley, Inspection and quality control, Organization for quality, The Normal
New York, 1977. distribution curve, Tchebyeheff's and Camp-Meidells inequality
4. Mathew P. Stephens and Fred E. Meyers, “Manufacturing Facilities theorems, Shewhart's bowl drawing experiments, Control charts for
Design & Material Handling”, (5e), Purdue University Press, 2013. variables, Interpreting patterns of variation on control charts for
5. David E. Mulcahy, “Materials Handling Handbook”, McGraw Hill variables, Type I and Type II Errors, Process capability analysis, Control
Professional, 1998. charts for attributes, Control chart for number of non-conformities per
unit. Acceptance sampling by attributes, Acceptable quality level, Lot
MME 4031: POWER PLANT ENGINEERING [3 0 0 3] tolerance percent defective, AOQ curve, AOQL, Average total
Choice of site for power station, load estimation, load duration curve, Inspection, Average fraction inspected, Producers risk, Consumers risk,
effect of variable load on power plant, Economics of power Acceptance sampling tables. Specifications and Tolerances,
generation.Hydro-Electric plants, Storage and pondage, flow duration Conventional and Statistical tolerancing, Precision, Accuracy and
and mass curves, hydrographs, Different types of fuels used for steam Reproducibility of method of measurements, Quality costs.
generation. Equipmentsfor burning coal in lump form, Equipment for
preparation and burning of pulverized coal, unit system and bin system. References:
Pulverized fuel furnaces, cyclone furnace.Coal and ash handling.Dust 1. Grant E. L and Levenworth R., “Statistical Quality Control”, McGraw
collection systems-Electrostatic Precipitator.Accessories for the steam Hill Publications, New York, 2005.
generator such as super-heaters, de-super-heaters, control of super- 2. Montgomery D.C., “Introduction to Statistical Quality Control”,
heaters, economizers, Air Pre-heaters and re-heaters.Cooling towers John Wieley and Sons, New York,2005.
and ponds, General arrangement of Diesel Power Plant. Gas Turbine 3. Juran J.M. and Gryna F.M., ‘Quality Planning and Analysis”, Tata
Power Plant, Principles of release of nuclear energy. Fusion and fission McGraw Hill Publications, Delhi, 1995.
reactions, Waste disposal. 4. Bertrand L. Hansen, “Quality Control- Theory and Applications”,
Prentice Hall India, Delhi, 1987.
References: 5. Duncan,A.J., “Quality Control and Industrial Statistics”, Irwin
1. Rajput R K, “Power Plant Engineering”, Laxmi Publication (P) Ltd, Press, New York, 1970
2010
2. Nag P K, “Power Plant Engineering”, Tata McGraw Hill Publishing
220
MME 4034: SUPPLY CHAIN AND LOGISTICS abnormal combustion, Principle of combustion chamber design for SI
MANAGEMENT [3 0 0 3] and CI engines. Rotary engine, CRDI, MPFI, TBI and GDI systems, Dual
Objective of a supply chain, Decision phases in a supply chain, Process fuel engines and stratified charge engines. IC engine pollutant formation,
view of a supply chain, Role of distribution in the supply chain, Design evaporative emissions, cranks case emissions and tail pipe emissions,
options for a distribution network, Factors influencing network design Exhaust emission control methods- ammonia injection. EGR and
decisions, Role of IT in network design, Making network design positive crank case ventilation.
decisions in practice, Transportation infrastructures and policies,
Tailored Transportation, Sourcing Decisions, In-house outsource, Third References:
and fourth party logistics providers, Supply scoring and assessment, 1. Ganeshan V., “Internal Combustion Engines”, (3e), Tata McGraw Hill
Supplier selection, Sourcing planning and analysis, Pricing and Revenue Education Private Limited, New Delhi, 2007.
management, Pricing and revenue management for multiple customer 2. Mathur and Sharma, ‘A Course in I C Engines”, Dhanpath Rai
segments, pricing and revenue management for perishable assets, Publishers, New Delhi, 1981.
Information Technology, Customer relationship management, Internal 3. John B. Heywood, “Introduction to Internal Combustion Engines”,
supply chain management, Supplier relationship management, Tata McGraw Hill Education Private Limited, New Delhi, 2011.
Transaction management foundation. 4. Lichty L.C., “International Combustion Engines”, McGraw Hill, New
Delhi, 1951.
References: 5. Edward F. Obert, “Internal Combustion Engines and Air Pollution”,
1. Chopra and Meindl., “Supply Chain Management Strategy, Planning Harper & Row, Publishers. Delhi, 1973.
and Operation”, (3e), Pearson Education, New Delhi, 2009.
2. Raghuram and Rangaraj, “Logistics and Supply Chain Management: MME 4037: TOTAL QUALITY MANAGEMENT [3 0 0 3]
Cases and Concepts”, Macmillan, New Delhi, 2000. Dimensions of Quality, Quality Planning, Quality costs Analysis,
3. Simchi-Levi and Kaminski, “Designing and Managing the Supply Techniques for Quality Costs, Basic concepts of Total Quality
Chain: Concepts, Strategies and Case Studies”, McGraw-Hill, Management. Quality Council, Quality Statements, Strategic Planning,
2003. Deming Philosophy, Barriers to TQM Implementation, TQM
4. Shapiro J., “Modelling the Supply Chain’, Duxbury Thomson Principles,Customer satisfaction and Retention, Employee Involvement -
Learning, U.S.A., 2009. Motivation, Empowerment teams, Continuous Process Improvement -
Juran Trilogy, PDSA Cycle, Kaizen, Supplier Partnership - Partnering,
MME 4035: TECHNOLOGY MANAGEMENT [3 0 0 3] sourcing, Supplier Selection, Supplier Rating, Relationship
Management of technology, system model, integrated and holistic Development, Performance Measures - Basic Concepts, Strategy,
model, Timing and innovation, technology and competition, Performance Measure, TQM Tools, Benchmarking Process, Quality
Entrepreneurs and innovation, entrepreneurship in corporations, Function Deployment, Taguchi Quality Loss Function, Total Productive
entrepreneurship, organizational barriers to innovation, venture team. Maintenance (TPM) - Concept of six sigma, ISO 9000:2000 Quality
Business plans for new ventures, successful product innovation, System - Elements, Implementation, Quality Auditing, QS 9000, ISO
sources of venture capital, Growth of new firms, Dynamics of new firms, 14000.
corporate systems, dynamic factors affecting growth, Innovation
Process, Forecasting Technology, Form of technology change, S-curve References:
jumps from radical to system innovation, Technology life cycle, 1. Besterfield Dale H., “Total Quality Management’, Pearson Education,
economic long cycles, Kondratieff waves, Technology and marketing, Delhi, 2006.
Sources of innovation, market pull and technology push, Corporate 2. James R. Evans & William M. Lindsay, ‘The Management and
research, Project strategy, sales volume and profitability in product life Control o’f Quality, (5e), South-Western Thomson Learning, 2002.
time, R&D projects, production costs, market share, profit margin. 3. Oakland John S, “Total Quality Management text with Cases”,
Elsevier, New Delhi, 2006.
References: 4. Besterfield Dale H, “Total Quality Management”, Pearson Education,
1. Gerard H Gaynor, “Handbook of Technology Management”, McGraw Delhi, 2012.
Hill International Edition, 1996. 5. Zeiri, “Total Quality Management for Engineers’, Aditya Books, Delhi,
2. Betz Frederick,” Managing Technology”, John Wiley & Sons, 2011. 1992.
3. Steele Lowell W and Badaww Michel K.,” Managing Technology,
4. Narayanan V. K., “Managing Technology and Innovation for MME 4038: WORK SYSTEMS ENGINEERING [3 0 0 3]
Competitive Advantage”, Prentice Hall, 2001. Productivity and work study, Productivity in the individual enterprise,
5. Rungachari Krishna, Chari C. P., “Technology Management and Factors tending to reduce productivity, Techniques for reducing excess
Business Development”. work content and ineffective time, Work study, Method study, Flow
process charts, Flow diagram, Multiple activity chart, Travel chart, String
MME 4036: THEORY OF INTERNAL COMBUSTION diagram, motion economy, Two handed process chart, Micro motion
ENGINES AND EMISSIONS [3 0 0 3] study, Therbligs, SIMO chart, Cyclegraph and Chronocyclegraph,. Use
Introduction to IC engines, Idealized cycles, Fuel air cycles and actual and basic procedure of work measurement, Techniques of work
cycles, modes of combustion, Stoichiometry, heat of formation, measurement, Time study, Rating, Introduction to Work sampling, Pre-
adiabatic flame temperature, chemical equilibrium, ignition limits. IC determined time standards (PTS) and Standard Data. Restricted work,
engine fuels: conventional and non-conventional fuels and their analysis. Pump diagram, Multiple machine work, Load factor, Machine
Petroleum refining processes and products, Qualities of SI and CI engine interference, Interference allowance, Working environment and
fuels and their ratings, alternative fuels: Alcohols, LPG, CNG, Hydrogen, Ergonomics, Safety criteria, Lighting, Noise and Vibration, Ventilation,
Vegetable oils. Stages of combustion in SI and CI engines: Normal and Climatic conditions.

221
References: MME 3283: INDUSTRIAL SAFETY ENGINEERING [3 0 0 3]
1. International Labour Office (ILO), “Introduction to work study”, Introduction to Safety Engineering, Industrial Accidents, Theories of
Universal Book Corporation, Geneva, 2001. Accident Causation, Introduction to Health and Toxic Substances,
2. Niebel B.W. and Frievalds, A., “Methods, Standards, and Work Environmental Control and Noise, Ventilation and its Design Principle,
design”, McGraw-Hill, New York, 2003. Personal Protection and First Aid, Fire Protection, Machine Guarding,
3. Barnes R.M., “Motion and Time Study-Design and Measurement of Safeguarding the point of operation, Power presses, Grinding machines,
work”, Willey International, Singapore, 1980. Saws, Belts and Pulleys, Safety consideration regarding material
handling and storage. Safety Requirement for Material Handling and
4. George K., “Work study, Universal Publishing Corporation”,
Storage, Electrical Hazards, Employee Participation in Promoting Safety,
Bombay, 1995.
Safety Training, Safety Committees, Teamwork Approach to Promoting
5. Niebel B.W., “Motion and Time Study”, (5e), Richard D.IrvinInc,
Safety.
Illinois, 1972
References:
OPEN ELECTIVES
1. Asfahl C R and Rieske D W, “Industrial Safety and Health
Management”, (6e), Pearson Education, 2011.
MME 3281: CORROSION ENGINEERING [3 0 0 3]
2. Spellman F R and Whiting N E, “The Handbook of Safety Engineering:
Definitions, corrosive environments, consequences of corrosion, cost of Principles and Applications”, Government Institutes, 2009.
corrosion, corrosion science and corrosion Engineering, fundamental
3. Gupta A., “Industrial Safety and Environment”, (1e), Laxmi
aspects of corrosion. Corrosion cell, cathodic and anodic reactions,
Publications Pvt. Ltd., 2006
types of corrosion cells, reference electrode, calomel electrode,
4. Goetsch D L, “Occupational Safety and Health for Technologists,
pourbaix diagrams. Corrosion rate expressions, electro-chemical nature
Engineers and Managers”, (8e), Pearson Education Limited, 2014.
of aqueous corrosion, polarization, factors influencing corrosion rate.
Types of corrosion, measuring polarization, anodic polarization, cathodic
polarization, activation polarization and concentration polarization. MME 3284: INTERNAL COMBUSTION ENGINES [3 0 0 3]
Corrosion prevention, materials selection, alteration of environments, Introduction to IC engine, Analysis of air standard cycles, fuel air cycles
design, cathodic and anodic protection, corrosion inhibitors, coatings. and actual cycles. Modes of combustion, Stages of combustion in SI &
Methods used to determine corrosion rate, weight loss measurements, CI engines, factors influencing the stages of combustion, normal and
linear polarization, Tafel extrapolation techniques. abnormal combustion, Control of abnormal combustion in SI and CI
engines. Combustion chambers in SI and CI engines. Supercharging &
References: Turbo-charging, Analysis of Modern developments in IC engines like
Wankel engine, Electronic injection systems in SI engines. Common Rail
1. Ahmed Zaki, “Principles of Corrosion Engineering and Corrosion
Direct Injection (CRDI) engines, Multi point fuel injection. (MPFI)
Control”, Elsvier science and Technology Books, 2006.
engines, dual-fuel engines and stratified charge engines. Introduction to
2. Mars G. Fontana, “Corrosion Engineering”, (3e), Tata McGraw Hill,
engine Electronics, typical engine management systems, position,
2008.
displacement and speed sensing, pressure, temperature and air
3. Trethewey K. R. and Longman J. Chamberlain, “Corrosion for measurement systems, exhaust oxygen sensors.
Students of Science and Engineering”, Scientific & Technical, 1988.
4. Schweitzer A Philip, “Fundamentals of corrosion-Mechanisms,
References:
Causes and preventive methods”, CRC Press, Tayler and Francis
1. Ganeshan V., “Internal Combustion Engines”, Tata McGraw Hill,
Group, 2010.
Education Private Limited New Delhi, 2007.
5. Uhlig H. H. and Revie R. W., “Corrosion and Corrosion Control”,
2. Mathur and Sharma, “A Course in I C Engines”, Dhanpath Rai
Wiley, 1985.
Publisher, New Delhi, 1981.
3. John B. Heywood,” Introduction to Internal Combustion Engines”,
MME 3282: ENERGY ENGINEERING [3 0 0 3]
Tata McGraw Hill, Education Private Limited New Delhi,2011.
Steam power plant - Different types of fuels used for steam generation,
4. Lichty L.C., “International Combustion Engines”, McGraw Hill New
Equipment for burning coal in lump form, Stokers, Diesel Engine power
Delhi, 1951.
plant - Method of starting diesel engine, Auxiliaries like cooling and
5. Edward F. Obert, “Internal Combustion Engines and Air Pollution”,
lubrication system, Filters, Centrifuges, Oil heaters, Intake and exhaust
Harper & Row, Publishers. Delhi, 1973.
system, Layout of diesel power plant. Hydro-electric plant:
Hydrographs, Flow duration and mass curves, Storage and pondage,
Pumped storage plants, Low, medium and high head plants, Penstock,
Water hammer, Surge tanks, Gates and valves, Nuclear Power Plant, MME 3285: INTRODUCTION TO ALTERNATIVE FUELS AND
Solar energy, Biomass energy, Wind energy, Ocean energy, Geothermal APPLICATIONS [3 0 0 3]
energy conversion, tidal energy conversion. Introduction to alternative fuels, Need for alternative fuels - Availability of
different alternative fuels for SI and CI engines. Properties of potential
References: alternative fuels, Liquid Fuels for SI Engines, Requirements of fuels for SI
1. Nag P K, “Power Plant Engineering”, Tata McGraw Hill, 2002. engines-Different Techniques of utilizing alternative liquid fuels Blends,
Neat form, Reformed fuels - Manufacturing, Storage and Safety-
2. Domkundwar, “Power Plant Engineering”, Dhanpat Rai Publications,
Performance and emission characteristics of alternative liquid fuels,
2003.
Liquid Fuels in CI Engines, Requirements of fuels for CI engines- Different
3. Rai G D, “Non-Conventional Energy Sources”, Khanna Publishers.
techniques for their utilization- Blends, Fuel modifications to suit CI
4. Rao S and Parulekar B B, “Energy Technology”, Khanna Publishers, engines, Dual fuelling, Ignition accelerators and other additives, Gaseous
2004. Fuels in SI Engines, Gaseous Fuels in CI Engines, Electrical Vehicles.
5. Culp A W, “Principles of Energy Conversion”, McGraw Hill
International, 2001.

222
References: formulated and solved using graphical and simplex methods and post
1. Ramadhas A. S., “Alternative Fuels for Transportation”, CRC Press, optimality analysis conducted. The special cases of LPP include
Taylor & Francis Group, 2010. transportation and assignment problems along with travelling salesman
2. Thipse S. S., “Alternative Fuels: Concepts, Technologies and problem. Game theory and various methods, waiting line models and
Developments”, Jaico Book Distributors, 2010. simulation. Poisson arrival rate and Exponential service times, System
3. GajendraBabu M. K., “Alternative Transportation Fuels: Utilization in characteristics, Problems on the models- (M/M/1): (M/M/1) : (N/FIFO),
Combustion Engines”, CRC Press, Taylor & Francis Group. 2010. Simulation of queuing models, Network model analysis using Critical
4. Michael F. Hordeski, “Alternative Fuels: The Future of Hydrogen”, The Path Method (CPM) and Project Evaluation & Review Technique (PERT).
Fairmont Press, 2008. Determination of probability/expectation of project completion.
5. James D. Halderman, “Hybrid and Alternative Fuel Vehicles”, (2e),
Prentice Hall, 2010. References:
1. Taha H. A., “Operations Research”, (7e), Pearson Education, 2002.
MME 3286: INTRODUCTION TO COMPOSITE MATERIALS [3 0 0 3] 2. Winston W.L., “Operations Research”, Thomson Asia, 2003.
Introduction to composite materials: definition, classification, types of 3. Vohra N. D., “Quantitative Techniques in Management”, 2007.
matrices and reinforcements, characteristics and selection. Micro 4. Sharma S. D., “Operations Research”, (14e),KedarNathRamnath
mechanical analysis of a lamina. Introduction, derivation of stress, Publications, 2005.
strain, modulus of elasticity of fiber reinforced composites. 5. Kanthi Swaroop, Gupta and Manmohan, “Operations Research”,
Manufacturing of polymer composites: method, advantages, Sultan Chand and Sons, 2003.
disadvantages and application. Application developments in aircrafts,
missiles, space, automobile, electrical and electronics, marine, MME 3289: INTRODUCTION TO QUALITY CONTROL [3 0 0 3]
recreational, sports equipment's and construction. Potential future Definitions of quality, Inspection and quality control, Organization for
applications of composites. Metal matrix composites and ceramic matrix quality, General quality control engineering fundamentals, Graphic
composites, reinforcement, matrix materials, characteristics and representation methods of frequency distribution, Measures of central
selection, base metal selection, applications. tendency and dispersion, Normal distribution curve, Inequality
theorems, Shewhart's bowl drawing experiments, Control charts for
References: variables (X, R and S charts), Type I and Type II Errors, Process capability
1. Mein Schwartz, “Composite Materials Handbook”, McGraw Hill analysis, Process capability indexes. Control charts for attributes (p, np,
Book Company, 1984. c and u charts). Acceptance sampling by attributes, Single and Double
2. Autar K. Kaw, “Mechanics of Composite Materials”, CRC Press, sampling plans, Operating characteristic curve, AQL, LTPD, AOQ curve,
2010. AOQL, ATI, AFI, Producer's risk, Consumer's risk, Acceptance sampling
3. Mallik P.C., “Fiber Reinforced Composites”, Marcel Decker, 1993. tables. Conventional and statistical tolerance, Precision, Accuracy and
4. Rober M. Joness, “Mechanics of Composite Materials”, McGraw Reproducibility of method of measurements. Quality costs.
Hill Kogakusha Ltd, 2008.
5. Michael W, Hyer, “Stress analysis of fiber Reinforced Composite References:
Materials”, McGraw Hill International, 1998. 1. Grant E L and Leavenworth R S, “Statistical Quality Control”, (7e),
Tata McGraw Hill Education, 2000.
MME 3287: INTRODUCTION TO NANOTECHNOLOGY [3 0 0 3] 2. Montgomery D C, “Introduction to Statistical Quality Control”, (6e),
Introduction to nanotechnology, Bottom-up and Top-down approaches, John Wiley and Sons Inc., 2009.
Physical and Chemical properties, General methods of preparation of 3. Mahajan M S, “Statistical Quality Control”, Dhanpat Rai Publishing
nanopar ticles, Carbon nanostructures, Characterization of Company Pvt. Limited, 2012.
Nanomaterials, Nanomanipulation, Overview of micro electro 4. Gryna F, Chua R C H, De Feo J A, “Juran's Quality Planning and
mechanical devices and Technologies, Microsensors, MEMS Analysis for Enterprise Quality’, (5e), McGraw Hill Education, 2007.
Fabrication Bonding, Deposition and Etching techniques, Lithography, 5. Hansen B L, “Quality Control: Theory and Applications”, PHI
LIGA technique, MEMS applications, Scope of nanotechnology as a Learning Education, 1987.
multidisciplinary subject, Nanomaterials used in energy and
Environmental applications Nanomaterials in automobiles, Health MME 3290: INTRODUCTION TO REFRIGERATION AND AIR
hazards and other Challenges. CONDITIONING SYSTEMS [3 0 0 3]
Basic concepts and Air Refrigeration Cycles, Vapor Compression
References: Refrigeration Systems, Vapor Absorption Refrigeration Systems,
1. Charles P Poole, “Introduction to Nanotechnology”, Wiley- Compound vapour compression refrigeration system. Multi-evaporator
Interscience, 2003. and cascade systems, Classification of Refrigerants, Comparison of
2. Guozhong Cao, “Nanostructures & Nanomaterials”, Imperial thermodynamic properties of refrigerants, Alternate Cooling Methods:
College Press, 2004. Desiccant Cooing System, Solar Refrigeration, Thermo Electric
3. Mohamed Gad-el-Hak, “The MEMS Handbook”, Taylor and Francis, Refrigeration, Analysis of Steam Jet Ejector Cycle, Refrigeration,
2005. Psychrometry, Psychrometric charts, Process involving Air-Vapour
4. James J Allen, “MEMS Design”, Taylor and Francis, 2005. Mixtures, Air Conditioning Systems, Types of Air Conditioners, Load
Estimation for inside and outside design conditions. Different types of
5. Mur thy B S, Shankar P, Textbook of Nanoscience and
heat loads.
Nanotechnology, Universities Press (India) Private Ltd, 2013.

References:
MME 3288: INTRODUCTION TO OPERATIONS RESEARCH [3 0 0 3]
1. Arora S.C. and Domkundwar S., “Course in Refrigeration and Air-
Definition, phases, applications, advantages and disadvantages of
conditioning”, Danpath Rai. New Delhi, 1992.
operations research. Linear programming problems (LPP) are

223
2. Cook Norman, “Refrigeration and Air conditioning”, Macmillan 3. Beach D S, Personnel: “The Management of the People at Work”,
London, 1995. (3e), Macmillan, 1975.
3. Stoecker. W.F., “Refrigeration and Air conditioning”, Tata McGraw 4. Yoder D, “Handbook of Personnel Management and Labor
Hill,1978. Relations”, Volume 1, McGraw Hill, 1958.
4. Prasad Manohar, “Refrigeration and Air conditioning”, New Age
International Pvt. Limited. New Delhi, 2004. MME 3293: PROJECT MANAGEMENT [3 0 0 3]
5. Jordon Richard C, Priester Gayle B, “Refrigeration and Air Concepts of Project and Project Management, Categories of projects,
conditioning”, Prentice Hall, 2008 Project life cycle phases, Tools and techniques for project management,
the project manager, Roles and responsibilities of a project manager.
MME 3291: INTRODUCTION TO ROBOTICS [3 0 0 3] Project Cost Estimation: Cost estimation, Capital cost, Operation and
Definition of Robot; Types of Robots; Robot Configuration; Selection of Maintenance costs, Cost estimation of a sample project. Feasibility
Robots; factor affecting the control resolution, Spatial resolution, Study: Types of feasibility. Project Network Construction, Critical path
Accuracy and repeatability, Specification of a robot, Robot method (CPM), Program evaluation review technique (PERT), Crashing
arm/manipulator Kinematics, Types of Grippers; Force Analysis of gripper of Project Network, Types of crashing. Resource levelling and Allocation
mechanism; Classification of Actuators; Actuators used in Robots - DC Technique, Project Audit: failures and reasons for audit, Phases of
motors, Stepper motors, AC motors and Servo motors, Robot project audit, Project check list. Project Management Performance:
Transmission Systems; Sensors; Types and classification of robot Performance indicators, Performance improvement, Project
sensors, Positional potentiometer, Velocity tachometer, Working of management environment. Project Management Software: InstaPlan,
resolver, Optical encoder, Magneto resistive skin, Hall generator, Electro- Yojana, Prism project manager, Primavera.
magnetic & Adhesive end effectors, proximity sensors; Tactile Sensing;
Robot Vision. References:
1. Paneerselvam R and Senthilkumar P, “Project Management”, PHI
References: Learning Pvt. Ltd., 2010
1. Janakiraman P. A., “Robotics and Image Processing”, Tata McGraw 2. Choudhury S, “Project Management”, (1e), Tata McGraw Hill
Hill, 1995. Education, 2008
2. Yoram Koren, “Robotics for Engineers”, Tata McGraw Hill, 1992. 3. Lock D, “Project Management”, (10e), Ashgate Publishing Limited,
3. Groover M.P., “Industrial Robotics”, PHI, 2008. 2013
4. Yu Kozyrev, “Industrial Robots Handbook”, MIR Pub, 1985.
5. Jain K.C., Aggarwal L. N, “Robotics Principles and Practice”, MME 3294: THERMAL TREATMENT OF METALS
Khanna Publishers, 1997. AND ALLOYS [3 0 0 3]
Introduction to phase diagrams, invariant reactions, analysis of phase
MME 3292: PERSONNEL MANAGEMENT AND INDUSTRIAL diagrams, Introduction to Iron-Carbon equilibrium diagram &
RELATIONS [3 0 0 3] Fundamentals of heat treatment, decomposition of austenite, TTT
Objectives of personnel management, Functions of Personnel diagram, Conventional case and Surface hardening treatments, factors
Management, Process of Human Resource Planning, Steps in affecting hardening, laser hardening. Age hardening and Thermo-
recruitment process, Sources of recruitment, methods of recruitment. mechanical treatments for Aluminium and Non-Ferrous alloys,
Promotions, Demotions, Transfers, Separation, Absenteeism and Turn Ausforming, Isoforming, Thermo-mechanical annealing Steel
over, Wage and Salary administration, Performance Appraisal, Methods specification, Classification and Application of steels and Cast iron with
of Per formance evaluation. Industrial Relations: Functional heat treatments, commercial steel, stainless steel, maraging steel,
Requirements, Employees participation in management. Grievances and Malleabilization. Heat treatment and Application of non-ferrous metals
Grievance Handling, Act of Indiscipline/Misconduct, Principles for and alloys defects, causes and remedies in heat treatment.
maintenance of discipline. Industrial Disputes, Procedure for the
Settlement of Disputes, Government and Industrial Relations, Organs of References:
Industrial Peace. Trade Unions: Objectives and Functions, Growth of 1. Rajan T. V., Sharma C. P. and Sharma Alok, “Heat Treatment
Trade Union Movement, Factors Affecting Growth of Trade Unions, Principles and Techniques”, PHI Publication, 1999.
Essentials of a Successful Trade Union. 2. Bolton W., “Engineering Materials Technology”, Heinmann
Newness, 2001.
References: 3. T h e l n i n g K . E . , “ S t e e l a n d i t s H e a t Tr e a t m e n t ” ,
1. Mamoria C B and Gankar S V, “Personnel Management”, (23e), Butterworth/Heinemann, 2000.
Himalaya Publishing House, 2003. 4. Singh Vijendra, “Heat Treatment of Metals”, Standard Publishers
2. Megginson L C, “Personnel and Human Resources Administration”, Distributors, 2012.
(3e), R. D. Irwin, 1977. 5. William D. Callister, “Materials Science and Engineering”, John
Wiley and Sons, 2007.

224
CSE 3292: PYTHON PROGRAMMING [3 0 0 3]
Getting started with python scripting, Using the file system, Reading
and writing files, Numerical Computing In Python, SciPy package,
Classes and object-oriented programming, Data types as objects,
Graphical user interfaces, Regular expressions, Network, web, and
database programming: Accessing databases in Python, Network
programming in Python, Creating a Python web application, Sample
project—creating a message wall, Web frameworks creating a model to
add database service – using SQLite; Cloud computing: google app
engine and web services: What is cloud computing, levels of cloud
computing service, what is the app Engine, The sandbox and the App
Engine SDK, Choosing an App Engine framework.

References:
1. Hans Peter Langtangen, Python Scripting for Computational Science,
(3e), Springer Publishers, 2014
2. Naomi R. Ceder, The Quick Python Book, (2e), Manning Publications
Co., 2010
3. Wesley J. Chun, Core Python Applications Programming, (3e),
Prentice Hall Publishers, 2012
4. Bill Lubanovic, Introducing Python - Modern Computing in Simple
Packages, O'Reilly Publication, 2015
5. Allen B. Downey, Think Python-How to think like a computer scientist,
(2e) O'Reilly Publication, 2015

IIE 5202: DIGITAL MEDICINE [3 0 0 3]


Present day practice of medicine. Limitations of scalability in the present
framework. Introduction to computing, algorithms, big data, semantic
web, mobility. Communication-WAN/LAN, 3G/4G and 5G.
Patient/Electronic Health records. Experience with these records
elsewhere Wearables, the physics of data capture. Practical
demonstration of wearables Genomics, an introduction. Computational
genomics including the software. Imaging –an introduction-ionizing and
non-ionizing. Imaging software and science of diagnosis. How all the
four 4 pillars-PHR/EHR, Wearables, Genomics and Imaging come
together with software as the glue to change the world of medicine.
References:
1. David Mount. Bioinformatics: Sequence and Genome Analysis.
CSHL, 2001
2. Durbin, Richard, Sean Eddy, Anders Krogh, and Graeme. Biological
Sequence Analysis: Probabilistic Models of Proteins and Nucleic
Acids. Cambridge University Press, 1999
CRA 4009

Data Scientist’s Toolbox and R Programming


Course: The Data Scientist’s Toolbox

 Data Science Fundamentals


 R and RStudio
 Version Control and GitHub
 R Markdown, Scientific Thinking, and Big Data

Course: R programming

 Background, Getting Started, and Nuts & Bolts


 Programming with R
 Loop functions and debugging
 Simulation and Profiling

Course: Getting and Cleaning data

 Finding Data and Reading Different File Types.


 Data Storage Systems and Extraction of Data
 Organizing, Merging, and Managing the Data
 Text and Date Manipulation in R

CRA 4010

Introduction to Data Science


Course: Exploratory Data Analysis

 Basics of Analytic Graphics and Plotting System in R


 Advanced Graphing Systems in R
 Statistical methods for Exploratory Data Analysis
 Case Studies in Exploratory Data Analysis

Course: Reproducible Research

 Concepts, Ideas, and Structure


 Markdown and KnitR
 Reproducible research Checklist and Evidence Based Data Analysis
 Case Studies and Commentaries
CRA 4011

Fundamental Techniques of Data Science


Course: Statistical Inference

 Probability and Expected Values


 Variability, Distribution, and Asymptotics
 Intervals, Testing, and P Values
 Power, Bootstrapping, and Permutation Tests

Course: Regression Models

 Least Squares and Linear Regression


 Linear Regression and Multivariable Regression
 Multivariable Regression, Residuals, and Diagnostics
 Logistic Regression and Poisson Regression

CRA 4012

Advanced Data Science


Course: Practical Machine Learning

 Prediction, Errors, and Cross validation


 The Caret Package
 Predicting with trees, Random Forests, and Model Based Predictions
 Regularized Regression and Combining predictors

Course: Developing Data Products

 Course Overview, Shiny, GoogleVis, Plotly


 R Markdown and Leaflet
 R Packages
 Swirl and Course Project

You might also like