This addendum provides 14 items that modify the specifications for upgrading the Conrad and Rossanley Control Station. The items include changes such as replacing pumps, adding ground fault protection requirements, updating piping leakage testing procedures, and replacing or adding design details. Sheet drawings are also replaced or added.
This addendum provides 14 items that modify the specifications for upgrading the Conrad and Rossanley Control Station. The items include changes such as replacing pumps, adding ground fault protection requirements, updating piping leakage testing procedures, and replacing or adding design details. Sheet drawings are also replaced or added.
This addendum provides 14 items that modify the specifications for upgrading the Conrad and Rossanley Control Station. The items include changes such as replacing pumps, adding ground fault protection requirements, updating piping leakage testing procedures, and replacing or adding design details. Sheet drawings are also replaced or added.
This addendum provides 14 items that modify the specifications for upgrading the Conrad and Rossanley Control Station. The items include changes such as replacing pumps, adding ground fault protection requirements, updating piping leakage testing procedures, and replacing or adding design details. Sheet drawings are also replaced or added.
Item No. Specification Location and Description of Change
1. Volume II Section 01 11 00 SUMMARY OF WORK:
Technical Specifications Remove: three 500 hp horizontal split case pumps
Add: one (1) 500 hp horizontal split case pumps
2. Volume II Section 26 24 19 LOW-VOLTAGE MOTOR CONTROL, 2.04.F.6 Technical Specifications Add: 6. Ground Fault Protection: a. Suitable for 480-volt, three-phase, three-wire, solidly grounded wye system. b. Ground sensors to encircle phase conductors and neutral conductor where used, and connected to ground relays with adjustable pickup settings and time-current characteristics indicated. c. Circuit breaker shunt trip and relay operating from fused 120-volt ac control source within control center. d. Manufacturers and Products: 1) Cutler-Hammer; GFR. 2) General Electric; GFM.
3. Volume II Section 40 80 01 PROCESS PIPING LEAKAGE TESTING
Technical 3.01.b.3.b; at end of paragraph ad the following line Specifications Add: This may include visual inspection of the joint for leakage under normal system operating pressure during startup.
Technical REQUIREMENTS; DRIVE MOTOR Specifications Remove: Motor nameplate horsepower shall not be exceeded at any head-capacity point on pump curve.
Replace with: The pump maximum power shall not exceed
510 horsepower at any head-capacity on the pump curve. 7. Volume III DWG 503-D-2001 Replace with new sheet 13, Rev. Addendum #2 Sheet 13 8. Volume III DWG 503-D-3001 Replace with new sheet 14, Rev. Addendum #2 Sheet 14 9. Volume III DWG 503-M-2001 Replace with new sheet 15, Rev. Addendum #2 Sheet 15 10. Volume III DWG 503-M-3001 Replace with new sheet 16, Rev. Addendum #2 Sheet 16 11. Volume III DWG 505-M-2001 Replace with new sheet 24, Rev. Addendum #2 Sheet 24 12. Volume III Detail 4091-305B: DWG 999-N-5001 Sheet 33 Remove: ½” V-307 and ½” SST PIPE
Add: ½” V-300 and 1/2" COPPER PIPE
13. Volume III Detail 4022-005: DWG 999-S-5001 Sheet 34 Remove: 3’-0” x 3’-0” MAX OPENING
Replace with: 3’-6” x 3’-6” MAX OPENING
2 Conrad and Rossanley Control Station Upgrade CIP #63-09 (336) Addendum #2
Item No. Specification Location and Description of Change
14. Volume III Add new design details: 0330-061, 1 OF 2 PIPE
Standard Details Refer to supplemental detail SUPPORT – CONCRETE packet SADDLE 0330-061, 2 OF 2 PIPE SUPPORT – CONCRETE SADDLE 0330-105 ADHESIVE DOWEL 0330-143 CONCRETE DEMOLITION 4005-500 PIPE SUPPORT 4005-518 BASE BEND
