Panduit P36E09

Intelligent PDU User Manual v4.
3
2
Table of Contents
Section 1 – System Overview ......................................................................................... 9
PDU Controller ............................................................................................................ 9
Connecting the PDU via Ethernet Port ........................................................................ 9
Connecting the PDU to a Computer Serial Port ......................................................... 10
Section 2 – Web Graphical User Interface (GUI) Configuration .................................... 11
Internet Protocol (IP) Addressing ............................................................................... 11
Connecting to the PDU .............................................................................................. 11
Web Configuration ..................................................................................................... 11
Introduction to the Web GUI ...................................................................................... 15
Screen Resize Due to Multiple PDU Configuration .................................................... 17
Menu Dropdowns ................................................................................................... 18
Introduction to the Dashboard ................................................................................... 18
Network Settings........................................................................................................ 19
System Management Information .............................................................................. 21
Setting Time and Date on the PDU............................................................................ 24
Outlet Power Management ........................................................................................ 27
Outlet Power Sequence Setup .................................................................................. 28
Setting Metering Thresholds ...................................................................................... 30
Email Setup ............................................................................................................... 42
Event Notifications ..................................................................................................... 46
Data Log .................................................................................................................... 48
Web Interface Access ................................................................................................ 50
Setting Up the System for RADIUS Authentication .................................................... 51
Configuring the system with LDAP Server Settings ................................................... 53
Section 3 – Simple Network Management Protocol (SNMP)......................................... 57
SNMP Management Configuration ............................................................................ 57
Configuring Users for SNMP V1/V2c ......................................................................... 59
INTELLIGENT PDU USER MANUAL

3
Configuring Users for SNMP v3 ................................................................................. 61

Configuring SNMP Traps ........................................................................................... 63
Section 4 – Local Display .............................................................................................. 66
Onboard Display and Network Controller .................................................................. 66
Control Buttons ...................................................................................................... 67
Network Controller Menu Structure............................................................................ 68
Main Menu Selections ............................................................................................ 68
Setup Menu ............................................................................................................ 69
Sensors Menu ........................................................................................................... 82
Section 5 – Daisy Chain Configuration .......................................................................... 83
Daisy-Chain Overview ............................................................................................... 83
Daisy-Chain Setup ..................................................................................................... 83
RNA (Redundant Network Access) Functionality ...................................................... 83
RNA Setup ................................................................................................................. 84
Power Share .............................................................................................................. 86
Section 6 – SmartZone Security Handle ....................................................................... 89
Configuring Cabinet Access Control .......................................................................... 91
Adding a User for Local Rack Access........................................................................ 93
Configuring Rack Access Settings. ............................................................................ 94
Configuring Handle Settings. ..................................................................................... 95
Configuring Keypad Settings ..................................................................................... 96
Remote Controlling the Handle. ................................................................................. 97
Controlling the Beacon. ............................................................................................. 99
The Status LED ....................................................................................................... 101
Setting Status LED State ......................................................................................... 102
Handle and Compatible Card Types ........................................................................ 102
Section 7 – SmartZone G5 Accessories...................................................................... 103
Hardware Overview ................................................................................................. 103
Configuring Temperature Scale ............................................................................... 105

4
Configuring Environmental Sensors ........................................................................ 105

Security ....................................................................................................................... 107
Non-volatile Storage ................................................................................................ 107
Authentication Data ................................................................................................. 107
Network Transport Security ..................................................................................... 107
Network Configuration Data ..................................................................................... 107
External Authorization Mechanisms......................................................................... 108
Other Features ........................................................................................................ 108
Warranty and Regulatory Information.......................................................................... 109
Warranty Information ............................................................................................... 109
Regulatory Information ............................................................................................ 109
Panduit Support and Other Resources........................................................................ 110
Accessing Panduit Support ...................................................................................... 110
Acronyms and Abbreviations ....................................................................................... 111
Appendix A: Sensor Configuration .............................................................................. 109
Door Switch Sensor ................................................................................................. 109
Dry Contact Input Sensor (side panel switch) .......................................................... 109
Temperature & Humidity Sensors ............................................................................ 110
Configuring Environmental Sensors ........................................................................ 111
Appendix B: Firmware Upgrade Options ..................................................................... 113
Web Interface Method ............................................................................................. 113
G5 Upgrade Utility (GUT) ........................................................................................ 113
USB Method ............................................................................................................ 114
FTPs Method ........................................................................................................... 114
Appendix C: Bulk Management of PDUs..................................................................... 116
G5 Upgrade Tool (GUT) .......................................................................................... 116
Appendix D: System Reset or Password Recovery .................................................... 119
Appendix E: PDU Alarms ............................................................................................ 120
Trap Codes assigned to Alarms List ........................................................................ 122

5
Appendix F: Panduit Network Controller Replace or Rotate 180° ............................... 129

Appendix G: Direct connect to the PDU by Changing Your PC’s IP Address.............. 131
Appendix H: Command Line Interface (CLI)................................................................ 137
CLI Commands ........................................................................................................ 140
Network Commands ................................................................................................ 143
User Commands ...................................................................................................... 144
Device Commands .................................................................................................. 145
Power Commands ................................................................................................... 146
Appendix I: RADIUS Server Configuration .................................................................. 149
Appendix J: Panduit G5 Accessories .......................................................................... 151
Appendix K: Compliance Model Number Details ......................................................... 152
Appendix L: JSON API Web Service ........................................................................... 153

6
Table of Figures
Figure 1: Ethernet Port for Network Connection .............................................................. 9
Figure 2: Status LED & Serial In Port Identified ............................................................ 10
Figure 3: Changing Your Password............................................................................... 12
Figure 4: After Login ...................................................................................................... 12
Figure 5: Change User Password ................................................................................. 13
Figure 6: Change Password .......................................................................................... 13
Figure 7: Login Page ..................................................................................................... 15
Figure 8: Landing Page/Dashboard .............................................................................. 15
Figure 9 - Resized Dashboard Screen .......................................................................... 17
Figure 10: Power Summary Page ................................................................................. 18
Figure 11: Outlet Monitoring Page ................................................................................ 19
Figure 12: Environmental Monitoring Page ................................................................... 19
Figure 13: Security Monitoring Page ............................................................................. 19
Figure 14: System Management ................................................................................... 21
Figure 15: System Management Configuration ............................................................. 22
Figure 16: Rack Location Configuration ........................................................................ 23
Figure 17: Power Panel & Core Location ...................................................................... 24
Figure 18: NTP Configuration ........................................................................................ 25
Figure 19: Daylight Saving Time Configuration ............................................................. 26
Figure 20: Control & Manage PDU ................................................................................ 28
Figure 21: Outlet Control Enabled ................................................................................. 29
Figure 22: Edit Outlets................................................................................................... 29
Figure 23: One-Delay Time ........................................................................................... 30
Figure 24: Saved Sequence .......................................................................................... 30
Figure 25: Power Threshold .......................................................................................... 31
Figure 26: Energy Threshold ......................................................................................... 33
Figure 27: Phase Current Alarm .................................................................................... 34
Figure 28: Phase Voltage Alarm ................................................................................... 36
Figure 29: Load Segment Breaker ................................................................................ 38
Figure 30: Device Detection Threshold Information ...................................................... 40
Figure 31: Outlet Information ......................................................................................... 41
Figure 32: Email Setup .................................................................................................. 43
Figure 33: SMTP Account Settings ............................................................................... 44
Figure 34: Email Recipients .......................................................................................... 45
Figure 35: Event Notifications ....................................................................................... 46
Figure 36: Data Log....................................................................................................... 49
Figure 37: Data Log Configuration ................................................................................ 49
7
Figure 38: User Settings................................................................................................ 52

Figure 39: RADIUS Configuration ................................................................................. 52
Figure 40: LDAP Configuration ..................................................................................... 54
Figure 41: Enable Role Privileges ................................................................................. 55
Figure 42: Test LDAP Configuration.............................................................................. 56
Figure 43: SNMP Management ..................................................................................... 57
Figure 44: SNMP General ............................................................................................. 58
Figure 45: SNMP Port ................................................................................................... 59
Figure 46: Setup SNMP Port and Trap Port .................................................................. 59
Figure 47: Define SNMP V1/V2c User .......................................................................... 60
Figure 48: Edit V1/2c Manager ...................................................................................... 60
Figure 49: SNMP V3 Manager ...................................................................................... 61
Figure 50: SNMP V3 Edit .............................................................................................. 62
Figure 51: SNMPv2 Configuration Information .............................................................. 63
Figure 52: SNMPv3 Trap Server Information. ............................................................... 64
Figure 53: Network Controller ....................................................................................... 66
Figure 54: Network Controller Menu Structure .............................................................. 68
Figure 55: Main Menu Selections .................................................................................. 69
Figure 56: Setup Menu .................................................................................................. 69
Figure 57: Network Submenu ........................................................................................ 70
Figure 58: Device Submenu .......................................................................................... 71
Figure 59: Screen Submenu ......................................................................................... 72
Figure 60: Language Submenu ..................................................................................... 73
Figure 61: USB Submenu ............................................................................................. 74
Figure 62: Units Submenu............................................................................................. 75
Figure 63: Alarms Menu ................................................................................................ 76
Figure 64: Power Menu ................................................................................................. 77
Figure 65: Device Submenu .......................................................................................... 78
Figure 66: Phase Submenu........................................................................................... 79
Figure 67: Breaker Submenu ........................................................................................ 80
Figure 68: Outlet Submenu ........................................................................................... 81
Figure 69: Sensors ........................................................................................................ 82
Figure 70: Connection Diagram RNA Daisy Chain ........................................................ 84
Figure 71: Connection Diagram Power Share & Daisy Chain ....................................... 87
Figure 72: SmartZone Security Handles ....................................................................... 89
Figure 73: Connection Diagram for SmartZone Security Handle .................................. 90
Figure 74: Rack Access Control Web GUI .................................................................... 92
Figure 75: Rack Access Control Actions Web GUI ....................................................... 92

8
Figure 76: Local Rack Access Web GUI ....................................................................... 94

Figure 77: Rack Access Settings Web GUI ................................................................... 95
Figure 78: Handle Settings Web GUI ............................................................................ 96
Figure 79: Remote Control ............................................................................................ 98
Figure 80: Beacon ......................................................................................................... 99
Figure 81: Beacon Settings Web GUI ......................................................................... 100
Figure 82: Status LED Settings Web GUI ................................................................... 102
Figure 83: Sensor Ports for Vertical PDU .................................................................... 104
Figure 84: Sensor Ports for Horizontal PDU ................................................................ 105
Figure 85: User Settings.............................................................................................. 105
Figure 86: Celsius Setting ........................................................................................... 105
Figure 87: Fahrenheit Setting ...................................................................................... 105
Figure 88: Door Switch Sensor Configuration ............................................................. 109
Figure 89: Dry Contact Cable ...................................................................................... 110
Figure 90: Temperature and Humidity Sensors ........................................................... 111
Figure 91: Sensor Ports on controller .......................................................................... 112
Figure 92: Upload Firmware ........................................................................................ 113
Figure 93: G5 Upgrade Tool Interface ......................................................................... 116
Figure 94: System Management Screen Web GUI ..................................................... 117
Figure 96: Example CSV File ...................................................................................... 118
Figure 98: Screws on Network Controller .................................................................... 129
Figure 99: Ribbon Cable for the Network Controller .................................................... 130
Figure 100: Control Panel ........................................................................................... 131
Figure 101: Network Status and Tasks ....................................................................... 132
Figure 102: Change Adapter Settings ......................................................................... 133
Figure 103: Properties ................................................................................................. 133
Figure 104: Ethernet Properties .................................................................................. 134
Figure 105: Internet Protocol Version 4 ....................................................................... 135
Figure 106: IP Settings for Direct Connection ............................................................. 136
Figure 107: Connect MA017 to the PDU In/Serial port ................................................ 138
Figure 108: Serial Cable Pinout .................................................................................. 139

9
Section 1 – System Overview

PDU Controller
All Panduit G5 Intelligent PDUs feature a Rotatable or Hot Swappable Intelligent
Network Controller (iNC). This centralized piece of intelligent hardware receives an IP
address, contains a Graphical Web Interface and is addressable over the network.
Connecting the PDU via Ethernet Port

Connecting the PDU to a LAN provides communication through an Internet or Intranet
connection enabling monitoring and control over the intelligent power distribution unit.
1. Connect an Ethernet cable to the Ethernet port on the PDU (see Figure 1).
2. Connect the other end of the cable to the Ethernet port on the router (or another
LAN device).
Network
Figure 1: Ethernet Port for Network Connection
From the factory the PDU defaults to DHCP and HTTPS connection. If you are
connected to a network with a DHCP server, the PDU automatically receives an IP
address and will display it on the OLED screen. If there is no DHCP server after several
minutes, the PDU defaults to IP address is 192.168.0.1, which will be displayed on the
PDU OLED screen. If the network cable is unplugged and plugged back in, the PDU
will restart the DHCP server search process.
10
Connecting the PDU to a Computer Serial Port

If unable to connect to network, you can change the network setting using the serial
interface.
To configure the network setting, perform the following steps:
1. Serial connect the PDU to a computer’s serial port. Set baud rate for a terminal
emulation program.
2. Using a CLI command to enable DHCP or set a static IP.
3. Verify access to the Web interface. The Ethernet LED on the PDU front panel
provides communication status by color and display activity (see Figure 2).
Status LED
Serial In
Figure 2: Status LED & Serial In Port Identified

Additional details in Appendix G.
11
Section 2 – Web Graphical User Interface (GUI)

Configuration
Internet Protocol (IP) Addressing
After the PDU receives an IP address, login to the Web interface to configure the PDU
and assign a static IP address (if desired).
Connecting to the PDU

1. Ethernet port on the PDU indicates solid green light on the right and a flashing
yellow light on the left. This indicates successful connectivity to the network.
2. Use the menu buttons to look up the IP address of the device on the OLED display
by selecting Setup > Network > IPv4 or IPv6 as applicable.
3. In a standard web browser, enter the PDU IP address (“https://IP ADDRESS”) and
proceed to configure the PDU as shown in the Web Configuration section.
Web Configuration
Supported Web Browsers
The supported Web browsers are Google Chrome (mobile and desktop), Mozilla
Firefox, Microsoft Edge and Apple Safari (mobile and desktop).
Changing Your Password

At initial login, you are required to change the default password:
1. Enter the current password and new password twice to confirm. By default,
passwords must be between 8 and 32 characters.

12
Figure 3: Changing Your Password

2. Click Change Password to complete the password change.
After the initial login, change the password by the following steps:
1. Go to User Name and select Change Password.
Figure 4: After Login
2. The Change User Password window opens.

13
Figure 5: Change User Password
3. Enter the old password and then new password twice to confirm. By default,
passwords must be between 8 and 32 characters.
Figure 6: Change Password

4. Click Change Password to complete the password change.
Logging in to the Web Interface

• Open a supported web browser and enter the IP address of the PDU (HTTPS)
• If browser displays “refused to connect” please double check that you are using
the “https://” protocol not “http://”

14
o If username and password have NOT been configured, use the default
username: admin and password: 12345678. For security purposes, a
change of password is required upon initial login.
o If admin credentials are lost use Appendix D to factory reset the PDU.

15
Introduction to the Web GUI

Login Page Note: https:// must be used (for initial login)
Figure 7: Login Page

Landing Page/Dashboard
Figure 8: Landing Page/Dashboard

16
Number Icon Description
The home icon provides an

overview of the PDU with
1 access to the Dashboard,
Identification, and Control
& Manage.
The Alarm icon provides
details of the active critical
2 alarms and active warning
alarms.
This icon lets you select a
Language. There are
seven languages available
3 to choose from: English,
Chinese, French, Italian,
German, Spanish, Korean
and Japanese.
This icon provides the logs
of the PDU which can be
viewed and downloaded.
4 • The Data Log is a
log of the Power,
Environmental, and
Security values.
The settings icon allows a
user to setup the Network
Settings, System
Management, SNMP
5
Manager, Email Setup,
Event Notifications, Trap
Receiver, Thresholds, and
Rack Access Control.
The search icon allows you
to input key words and
6 search for the related
results.
Information about the PDU
can be found using this
7 icon. You also can also

17
Number Icon Description
click user guide and

license to ask for help.
This icon shows who is
logged in (user or admin).
Account passwords can be
8
changed, and user
accounts managed
through this page.
Screen Resize Due to Multiple PDU Configuration

Resizing a Screen
Multiple PDUs can now cause the user to resize the screen to fit the information on the
dashboard due to the update.
Figure 9 - Resized Dashboard Screen

18
Menu Dropdowns
Overview Alarms Help Language Logs Settings Admin
Introduction to the Dashboard

Power Summary Page
Figure 10: Power Summary Page

19
Outlet Monitoring Page
Figure 11: Outlet Monitoring Page

Environmental Monitoring Page
Figure 12: Environmental Monitoring Page
Security Monitoring Page
Figure 13: Security Monitoring Page
Network Settings
The Network Settings allow management of IP Configuration, Web RESTapi Access
Configuration, SSH/FTPs Configuration, Network Time Protocol (NTP), Date/Time
Settings and Daylight-Savings Time.

20
IP Configuration:
Web RESTapi Access Configuration can be used to set HTTP, HTTPS or Disable the
onboard Web GUI.

21
SSH/FTP Configuration:
System Management Information

The system management information is a way to distinguish the PDU system’s name
and location inside the data center.
To configure the system management information, select System Management under

the gear icon.
Figure 14: System Management

22
System Info
The system information includes the name of the PDU system and information of the
person to contact in case an issue arises. Follow the steps below to set up the system
information:
1. Select the pencil icon next to System Management.
Figure 15: System Management Configuration
2. Enter the System Name: The “system” is the main PDU and all daisy-chained
PDUs. A system can have 4 PDUs.
3. Enter the name of the person who should be contacted if there is a problem with
the system into the Contact Name section.
4. Enter the email of the contact person into the Contact Email.
5. Enter the phone number of the contact person into Contact Phone.
6. Enter the location of the contact person into the Contact Location.
7. Press Save.
a. Note: If editing ‘system management’ – all fields are required to be filled
to save the information.
Rack Location
The rack location describes the physical location of the rack or cabinet where the PDU

23
system resides. To setup the system information, follow these steps.
1. Select the pencil icon next to Rack Location.
Figure 16: Rack Location Configuration
2. Enter the room location of the rack or cabinet that contains the PDU system into
Room Name.
3. Enter the name of row where the PDU is located in Row Name.
4. Enter the position of the row where the PDU is positioned in Row Position.
5. Enter the ID of the rack/cabinet where the PDU is located into Rack ID.
6. Enter the height of the rack/cabinet where the PDU is located into Rack Height.
7. Press Save.
Power Panel & Core Location

The Power Panel & Core Location describes the name of each PDU that is part of the
PDU system. It also indicates the location of the PDUs inside the rack or cabinet. To
configure, follow these steps:
1. Select the pencil icon next to Power Panel & Core Location.

24
Figure 17: Power Panel & Core Location

2. Enter the name of the PDU in the Power Panel Name.
3. Select Front or Back for the Core Location. The Core Location is the side of
the rack/cabinet where the PDUs are installed. For vertical PDUs, they are
typically installed in the back.
4. Enter the rack unit (RU) location into the Core U Position. Vertical PDUs are
usually installed in the 0 RU space.
5. Press Save.
Note: If editing ‘Power Panel & Core Location’ – all fields are required to be filled to
save the information.
Setting Time and Date on the PDU

You can set the internal clock manually or link to a Network Time Protocol (NTP) server
and set the date and time:
Manually Setting Time and Date

1. Go to Network Settings and select Date/Time Settings.

25
2. Enter the date using the YYYY-MM-DD format or use the calendar icon to select
a date.
3. Enter the time in the three fields provided: the hour in the first field, minutes in the
next field, and seconds in the third field. Time is measured in 24-hour format.
Enter 13 for 1:00pm, 14 for 2:00pm, etc.
4. Press Save.
Link to a Network Time Protocol (NTP)
1. Go to Network Settings and select Network Time Protocol (NTP).
Figure 18: NTP Configuration

26
2. Click Enable to enable NTP.

3. Enter the IP address of the primary NTP server in the Primary NTP Server field.
4. Enter the IP address of the primary NTP server in the Secondary NTP Server
field.
5. Select the appropriate time zone from the Time Zone drop-down list.
6. Press Save.
Note: NTP Server must be online to test and save the settings.
Setting Daylight Saving Time

1. Go to Network Settings and select Daylight Saving Time.
Figure 19: Daylight Saving Time Configuration
2. Ensure Enable is selected.

3. Select the specifics of the Start Month:
• Month
• Week
• Day
• Time

27
4. Select the specifics of the End Month:
• Month
• Week
• Day
• Time
5. Set the Time Offset.
Outlet Power Management

Naming an Outlet
For Panduit PDUs with outlet level control or monitoring, you can customize each outlet
and view all circuit breaker to outlet associations through the Web GUI.
1. In the Control & Manage tab, expand the Outlet Information folder by clicking
the pencil icon.
2. Select the outlet to name. In the data panel, select the value field for the Outlet
Name.
3. Delete the default name and type the new name.
4. Press Enter.
Setting the Outlet Default State

Setting the Outlet Default State on Panduit PDUs with outlet level control allows the
user to determine the initial power status of an individual outlet upon PDU power up.
1. Expand the Outlet Information folder from the Control & Manage tab.
2. In the PDU settings dialog box, choose a selection from the State on Startup
dropdown menu:
• On: this will turn an outlet on upon initial startup
• Off: this will turn an outlet off upon initial startup
• Last Known: this will restore outlets to the last known power states before
the device was shut down
Switching an Outlet On or Off

This is only applicable to outlet-switched PDUs.
• Outlets on the switched PDU models in the Panduit PDU are easily switched
on, switched off, or power cycled. This action requires the user to have

28
Administrator Privileges.
1. Select the Control & Manage folder from the Home icon.
2. In the Power Control panel, select the outlet that must be switched on, switched
off, or reboot.
3. Select the desired Power Control from the dropdown menu.
4. Select Apply.
Setting the Outlet Power On/Off Delay for Panduit PDUs

This is only applicable to outlet-switched PDUs. When the PDU is turned ON, outlets
will consecutively power on from Outlet 1 to the highest available outlet number.
1. Select the Home Icon then Control & Manage from the drop-down menu in the
Web UI.
2. Select the outlet(s) for which to set a delay by clicking on the pencil icon.
3. Configure the length of the delay and/or length of reboot.
4. Select Save.
Outlet Power Sequence Setup

The outlets can be programmed to have a pre-determined on delay or off delay. (E.g.
On Delay can be used to implement power on sequencing to avoid surge spikes or
circuit breaker overload associated with IT equipment all being turned on at the same
time.)
1. From the PDU GUI Home Menu, select Control & Manage.
Figure 20: Control & Manage PDU

29
2. Select Outlet Control Enabled.
Figure 21: Outlet Control Enabled
3. For each Outlet select the Edit pencil.
Figure 22: Edit Outlets
4. In the Edit Outlet window enter the On-Delay time (0-7200 seconds) then select
Save.

30
Figure 23: One-Delay Time
5. Your Outlet Power Sequence has been set.
Figure 24: Saved Sequence

Setting Metering Thresholds
Power Threshold
The PANDUIT PDU will send alert notifications when a power threshold wattage
crosses above or below the settings you specify in the Power Threshold configuration:

31
1. Go to the Thresholds > Input Page.

2. Click the pencil for the Power Threshold to update.
Figure 25: Power Threshold
3. Select and enter the appropriate thresholds in amps and click Save.
• Lower Critical (W)
• Lower Warning (W)
• Upper Warning (W)
• Upper Critical (W)
• Reset Threshold (W)

32
The Reset threshold is the number of watts the reading needs to fall below
the threshold setting for the condition to be cleared.
For example, the current critical threshold for the input phase is set to 19
watts (W). The current draw rises to 20W, triggering a Current Critical alert.
The current then continues to fluctuate between 18.1W and 20W. With the
reset threshold set to 1W, the PDU continues to indicate that the current on
the input phase is above critical. Without a reset threshold (that is, the reset
threshold is set to zero), the PDU would de-assert the condition each time the
current dropped to 18.9W and re-assert the condition each time the current
reached 19W or higher. With the fluctuating current, this could result in
repeating event notifications, such as SNMP traps, SMTP alerts or Syslog
notifications.
• Alarm State Change Delay (samples)

If enabled, the PDU asserts any warning or critical condition only after a
specified number of consecutive samples that cross a threshold are
generated. This prevents several threshold alerts from being generated if the
measurements return to normal immediately after rising above an upper
threshold or dropping below a lower threshold.
4. Repeat steps 1 - 3 for all PDUs.
Energy Threshold
The PANDUIT PDU will send alert notifications when an energy threshold kilowattage
crosses above or below the settings you specify in the Energy Threshold configuration:
1. Go to the Thresholds > Energy Page.

2. Click the pencil for the Energy Threshold to update.

33
Figure 26: Energy Threshold
3. Select and enter the appropriate thresholds in kilowatts and click Save.
• Upper Critical (kWh)
• Upper Warning (kWh)
• Reset Threshold (kWh)

4. Repeat steps 1 - 3 for all PDUs.

34
Phase Current Alarm Threshold

The PANDUIT PDU will send alert notifications when a phase current alarm amp
crosses above or below the settings you specify in the Phase Current Alarm
configuration:
1. Go to the Thresholds > Phase Page.

2. Click the Pencil for the Phase Current Alarm to update.
Figure 27: Phase Current Alarm
• Lower Critical (A)

35
• Lower Warning (A)
• Upper Warning (A)
• Upper Critical (A)
• Reset Threshold (A)
• Alarm State Change Delay (A)

The Reset threshold is the number of amperage the reading needs to fall
below the threshold setting for the condition to be cleared.
amps (A). The current draw rises to 20A, triggering a Current Critical alert.
reset threshold set to 1A, the PDU continues to indicate that the current on
current dropped to 18.9A and re-assert the condition each time the current
reached 19A or higher. With the fluctuating current, this could result in
notifications.

4. Repeat steps 1 - 3 for all phases.
Phase Voltage Alarm Threshold

The PANDUIT PDU will send alert notifications when a phase voltage crosses above or
below the settings you specify in the Phase Voltage Alarm configuration:
1. Go to the Thresholds > Phase Page.

2. Click the pencil for the Phase Voltage to update.

36
Figure 28: Phase Voltage Alarm
3. Select and enter the appropriate thresholds in voltage and click Save.
• Lower Critical (V)
• Lower Warning (V)
• Upper Warning (V)
• Upper Critical (V)
• Reset Threshold (V)

The Reset threshold is the number of amps the reading needs to fall below

37
voltage (V). The current draw rises to 20V, triggering a Current Critical alert.
The current then continues to fluctuate between 18.1V and 20V. With the
reset threshold set to 1V, the PDU continues to indicate that the current on
current dropped to 18.9V, and re-assert the condition each time the current
notifications.

4. Repeat steps 1 - 3 for all phases.
Circuit Breaker Alarm Threshold

The PANDUIT PDU will send alert notifications when a circuit breaker amperage
crosses above or below the settings you specify in the Circuit Breaker Alarms
configuration:
1. Go to the Thresholds > Circuit Breaker Page.

2. Click the pencil for the Circuit Break to update.

38
Figure 29: Load Segment Breaker
• Lower Critical (A)
• Lower Warning (A)
• Upper Warning (A)
• Upper Critical (A)
• Reset Threshold (A)

39
amps (A). The current draw rises to 20A, triggering a Current Critical alert.
The current then continues to fluctuate between 18.1A and 20A. With the
current dropped to 18.9A and re-assert the condition each time the current
notifications.

Repeat steps 1 - 3 for all circuit breakers.
Device Detection Threshold

The Device Detection Threshold is the minimum threshold before current will be
reported. Any detected current below the threshold will be reported as zero. To change
this threshold, follow the following steps:
1. Go to the Thresholds > Outlet Page.
2. Click the pencil next to Device Detection Threshold.

40
Figure 30: Device Detection Threshold Information
3. Change the value for the number of milli-amps to set the threshold.
Outlet Alarm Threshold
The PANDUIT PDU will send alert notifications when an outlet amperage crosses above
or below the settings you specify in the Outlet Alarms configuration:
1. Go to the Thresholds > Outlet Page.

2. Click the pencil for the Outlet to update.

41
Figure 31: Outlet Information
3. Select and enter the appropriate thresholds in amps and then click Save.
• Lower Critical (W)
• Lower Warning (W)
• Upper Warning (W)
• Upper Critical (W)
• Reset Threshold (W)

42
watts (W). The current draw rises to 20W, triggering a Current Critical alert.
current dropped to 18.9W and re-assert the condition each time the current
reached 19W or higher. With the fluctuating current, this could result in
notifications.

Repeat steps 1 - 3 for all outlets.
Email Setup
The Panduit PDU can be configured to send Emails to specific users when an event
occurs. To do this, the information about the SMTP (Simple Mail Transfer Protocol)
server needs to be configured.
Note: SMTP does not support SSL.
1. From the top ribbon of the dashboard, go to the gear settings and select Email
Setup.

43
Figure 32: Email Setup
2. Select the pencil icon next to SMTP Account Settings and begin filling out the
Edit screen.

44
Figure 33: SMTP Account Settings
• Set the Email Server Address. This is the IP address of the SMTP that is
going to accept the messages.
• Set the Sender Address. This is the email address that the email is sent
from. You could use a unique email address on each PDU or the same
email address across all PDUs.
• Configure the Port number. The port number is the communication

endpoint on the server. The default is 25. Other common SMTP ports are
587 and 465
• If the SMTP server requires authentication, enter the username and

password. These will be determined by the configuration on the SMTP
server. If the SMTP does not require authentication, a username and
password will need to be entered, but they will not be used.
• Set Number of Sending Retries. This will be the number of times the

45
PDU will attempt to resend a message if the message fails. The default
setting is 3.
• Set Time Interval Between Sending Retires (In Minutes). This is the
time, in minutes, the PDU will wait before retrying to send a failed
message. The default setting is 6 minutes.
• Choose whether Server Requires Password Authentication is needed

or not. If the SMTP server requires a username and password, this option
needs to be selected.
3. Press Save when done.
Next, fill out the Email Recipients list.
1. Select the pencil icon to display the Email Recipients screen.
Figure 34: Email Recipients
2. Enter the desired email address and press Enable.

3. Press Save.
Note: A maximum of 5 users can be entered to receive email alerts.

46
Event Notifications
The SmartZone G5 iPDU can be configured to provide event notifications.
Figure 35: Event Notifications
Note: Not every Event Notification applies or is supported by every PDU type even
though the toggle switch in the Web GUI may seem like the feature is supported. In that
instance the user is advised to ignore that toggle switch.

47
Below is a table of PDU types and the Event Notifications that particular PDU type
supports.
Event Notifications Monitored Input Monitored Monitored Monitored and
(MI Series) Switched Per Outlet Switched Per
(MPO Outlet (MSPO
(MS Series) Series) Series)
Circuit Breaker X   
Status Changed
User Activity    
Smart Rack    
Access
Outlet Power X  X 
Control Status
Changed
User Status    
Changed
Critical Alarm    
Warning Alarm    
Password/Settings    
Changed
Network Card    
Reset/Start
External Sensor    
Status Changed
PDU    
Configuration File
Imported/Exported
User Role Status    

Changed

48
Firmware Updated    
Communication    
Status Changed
Daisy Chain    
Status Changed
Enter Bootloader    
Mode
LDAP/Radius    
Error
Power Share    
Changed
Data Log
The period visible in the data log at any one time depends on the time between data log
entries. The time range of each record can be configured from 1 to 1440 minutes. (As
an example, if a data log is in an interval of 10 minutes, the entire data log contains
2000 records with up to 13.89 days of data.) Once the data log reaches the maximum of
2000 records, the oldest entries ae overwritten by the newer entries.
1. Go to Logs and select Data Log.

49
Figure 36: Data Log
2. Select the Actions drop-down menu and choose Data Log Configuration.
Figure 37: Data Log Configuration
3. Enable must be selected and enter an interval number in the Log Interval field.
(Valid range is from 1 to 1440 minutes. The default time is 10 minutes.)
4. Select Save.

50
Web Interface Access
Logging Out
Users should logout after each session to prevent unauthorized changes to the system.
1. Click the user name icon in the top right corner of the screen (see Introduction
to the Web Menu).
2. Click Log Out in the drop-down menu.
Access Types
There are two levels of access privileges:
• Administrator Privileges
• Read Only
The PDU comes with a standard Administrator Privileges profile and a standard Read
Only profile. The “Admin Role” is typically the system administrator and has the
Administrator Privileges with full operating permissions. By default, the User Role is a
Read Only profile. All other users must be added by a user with administrator
privileges. Users are defined by their unique login credentials and by their user role. The
level of access privilege determines what the user will see and what actions the user
can perform. The level of access privilege determines which menu items the user can
access, or which fields display on individual setting and configuration dialogs. Before
setting up users, determine the Roles that will be required. Each user must be given
a Role. These Roles define the permissions granted to the user.
Role Default Permissions
admin Full permissions that cannot be modified or deleted.
user Read-only permissions. Can monitor the system but

cannot change any configuration
manager Full permissions that can be modified and deleted
User Accounts
Add a user with the following steps:
1. Go to User Administration and select User Accounts.

51
2. Select Add User to create a new user profile.

3. Use the Settings tab to enter the following information:
• User Name (required)
• Password (required)
• Confirm Password (required)
NOTE: Set password requirements in the required field. By default, passwords

must be 8-32 characters in length, and have at least one numeric character, and
at least one special character.
4. Use the Roles tab to set full or read only privileges.

5. Select Add User to save the new user profile.
Modify user profile:
1. Go to User Administration and select Users.

2. Select the User Name.
3. Select Edit. Make changes to the user profile.
4. Select Update.
Delete user profile with the following steps:
1. Go to User Administration and select Users.

2. Select the red X next to user name.
Setting Up the System for RADIUS Authentication

1. Go to User Settings in the admin menu.

52
Figure 38: User Settings
2. Go to RADIUS Configuration and click the edit pencil.
Figure 39: RADIUS Configuration

53
3. Select the Enable button.

4. Enter Server IP address field, Port number field, and Secret field.
5. Click save and your Radius authentication is complete.
Note: By default, a RADIUS user will have the “user” Role if one is not specified. The
administrator of the RADIUS server may configure a Panduit vendor (19536) dictionary, with a
“User-Role” integer attribute set to User (1) or Admin (2). When this User-Role attribute is the
first attribute for the user, that user will have the admin Role after logging in. For complete
details, see Appendix H: Radius Server Configuration
Configuring the system with LDAP Server Settings
To setup LDAP to access the Active Directory (AD) and provide authentication when
logging into the PDU via the Web Interface:
1. Go to User Settings (under the ADMIN Menu) > LDAP Configuration.
2. Select the LDAP Enable checkbox.
3. Use the drop-down menu to choose the Type of LDAP Server. Choose Microsoft
Active Directory.
4. Enter an IP Address of the domain controller/Active Directory (AD) Server.
i.e.: 192.168.1.101 (example)
5. Enter a Port.
Note: For Microsoft, this is typically 389.
6. In the Base DN field, enter in the account to be used to access AD.
i.e. CN=myuser, CN=Users, DC=EMEA, DC=mydomain, DC=com
7. Enter the password in the Bind Password and Confirm Password fields.
8. In the Search User DN field:
DC=subdomain
DC=mydomain
DC=com 10
9. In the Login Name Attribute field, enter sAMAccountName (typically).
10. In the User Entry Object Class field, enter person.

54
With these LDAP settings configured, the Bind is complete.
Figure 40: LDAP Configuration
Once LDAP is configured, the PDU must understand for which group authentication
occurs. A role must be created on the PDU to reference a group within the Active
Directory (AD).
1. Within the Active Directory, create a group for the users that you wish to be PDU
administrators. i.e. admins
Note: There are no limits to the amounts of admins that the PDU imposes.
However, there may be limits by the LDAP server.

55
2. Within the PANDUIT PDU Web Interface, go to User Settings (under admin
menu) > Roles. Enter the Role Name that was created in AD. i.e. admins
3. Enable role privileges as needed (pictured below).
Figure 41: Enable Role Privileges
4. LDAP authentication is ready to use.

5. Click save to test and click LDAP Configuration again.
6. Type an Active Directory user name/password into the test box.
7. Click Test LDAP Configuration.
• If a box pops up with all green SUCCEEDED (no X’s), the LDAP is
successfully configured.

56
Figure 42: Test LDAP Configuration
Note: Be sure to log in without a domain name.

57
Section 3 – Simple Network Management

Protocol (SNMP)
SNMP Management Configuration
Setup SNMP
1. Access the Web interface and login.
2. Under SNMP Managers, select SNMP General (or type SNMP in the search).
The SNMP General page displays.
Figure 43: SNMP Management

58
3. The SNMP General includes SNMP Access and Version.
Figure 44: SNMP General
Setup SNMP Port

1. Access the Web interface and log in.
2. Under SNMP Managers, select SNMP Port. The SNMP Port page displays.

59
Figure 45: SNMP Port
3. Set up SNMP Port and SNMP Trap Port.
Figure 46: Setup SNMP Port and Trap Port
Configuring Users for SNMP V1/V2c

2. Under SNMP Manager, select SNMP V1/V2c.
3. In the SNMP V1/V2c panel, select the SNMP V1/V2c manager to configure.
Select the pencil icon.

60
Figure 47: Define SNMP V1/V2c User
4. The Edit panel pop up displays.
Figure 48: Edit V1/2c Manager
5. Set the following options:
• IP Address: the IP address of the host for this SNMP V1/V2 manager. Only
requests from this address will be acted upon.

61
Note: An IP address configured to 0.0.0.0 will act as a wildcard and all requests
will be acted upon.
• Read Community: the read-only community string to allow an SNMP V1/V2c

manager to read a SNMMP object.
• Write Community: the write-only community string to allow an SNMP V1/V2c

manager to write an SNMMP object.
6. Click Enable and Save.
Configuring Users for SNMP v3

2. Under SNMP Managers, select SNMP V3.
3. In the SNMP V3 panel, select the SNMP V3 manager to configure. Select the
pencil icon in the last column.
Figure 49: SNMP V3 Manager
4. The Edit panel pop-up displaying the configurable options.

62
Figure 50: SNMP V3 Edit
5. Configure the SNMP username

6. Choose a Security Level from the dropdown menu
• NoAuthNoPriv: No authentication and no privacy. This is the default.
• AuthNoPriv: Authentication and no privacy.
• AuthPriv: Authentication and privacy.

7. Enter a new unique password to be used for authentication
8. Select the desired authentication algorithm.
• MD5
• SHA

63
9. Enter a new unique key for privacy algorithm

10. Select the desired privacy algorithm
• AES-128
• AES-192
• AES-256
11. Click Enable and Save.
Configuring SNMP Traps

The PDU keeps an internal log of all events. These events can be used to send SNMP
traps to a third-party manager. To set up the PDU to send SNMP traps, follow the
following procedure:
Configuring SNMP v1 Trap Settings

1. Go to Device Configuration > Network Services > SNMP
2. Click the Pencil next to SNMPV1 Trap Receiver you want to update.
Figure 51: SNMPv2 Configuration Information
3. Enter the Name, Host, and a community name in the fields provided.
a. The name is a user assigned name to help distinguish the different receivers.
b. The host name is the IP Address to which the traps are sent by the SNMP

64
system agent.
c. Community is the password on the SNMP management stations.
4. Select Enable to enable the receiver.
5. Select Save to save and exit.
Configuring SNMP v3 Trap Settings

1. Go to Device Configuration > Network Services > SNMP
2. Click the Pencil next to SNMPV3 Trap Server you want to update.
Figure 52: SNMPv3 Trap Server Information.
3. Enter the Name, Host, and a community name in the fields provided.
a. The name is a user assigned name to help distinguish the different receivers.
b. The host name is the IP Address to which the traps are sent by the SNMP
system agent.
4. Choose a Security Level from the dropdown menu
• NoAuthNoPriv: No authentication and no privacy. This is the default.

65
• AuthNoPriv: Authentication and no privacy.
• AuthPriv: Authentication and privacy.

5. Enter the password from the SNMP Server to be used for authentication.
6. Select the desired authentication algorithm.
• MD5
• SHA
7. Enter the key from the SNMP Server for privacy algorithm
8. Select the desired privacy algorithm
• AES-128
• AES-192
• AES-256
9. Select Enable to enable the receiver.
10. Select Save to save and exit.

66
Section 4 – Local Display

Onboard Display and Network Controller
The Onboard Display provides information about the PDU and connected devices. The
PDU has a three-button, graphical Network Controller panel (see Figure 22). Use the
buttons to change the screen display and retrieve specific data.
Display
Figure 53: Network Controller
The Network Controller Display has three modes:
1. Menu mode (Network Controller Display main menu): When the PDU is powered
up or when a button is pushed while in Standby Mode or Power Save mode.
2. Standby mode: This happens when a PDU is idle (no buttons pushed) for 30
seconds while in Menu mode.
• In Standby mode, the PDU scrolls through key power values (Frequency, Amps, Volts,
Watts, and kVA) and IP addresses (for both IPv4 and IPv6).

67
3. Power Save mode: The PDU enters Power Save mode when it has been in
Standby mode for an hour. To exit Power Save mode, press any button on the
display.
Control Buttons
The table below summarizes how to use the control buttons on the Network Controller
display.
Button When in Menu Mode When in Screensaver

Mode
Menu Select from the four main Returns to the previous

menus. display screen before
entering the screensaver
mode.
Scroll Scrolls down through the Returns to the previous
list of menu items. display screen before
NOTE: A highlighted menu entering the screensaver
item is ready to be mode.
selected.
Select Opens the selected menu. Returns to the previous
display screen before
entering the screensaver
mode.
Status LED
The LED will change colors depending on the state of the PDU.
LED State Description
Solid Green Normal Operation
Solid Red Critical or Warning Alarm
Flashing Orange No network connection

68
Network Controller Menu Structure
Figure 54: Network Controller Menu Structure
Main Menu Selections

The PDU menu selection hierarchy consists of Setup, Alarms, Power, and Sensors. On
the main menu, scroll down to highlight Setup. Press Select. Scroll down to select a
submenu and press Select to display the submenu options. Press Menu to return to the
previous menu.

69
Figure 55: Main Menu Selections
Setup Menu
The Setup menu provides user configuration options including Network, Device, Screen,
Language, USB, and Units.
Figure 56: Setup Menu
Network Submenu
The Network submenu allows you to view IP address IPv4 or IPv6. On the Setup menu,
scroll down to Network. Press Select to enter the Network Submenu. Scroll down to
highlight the selected option from the menu. Press Select to display the screens that
display the IP address. Press Menu to return to the previous menu.

70
Figure 57: Network Submenu
Device Submenu
The Device submenu provides the SKU number, Serial number, MAC address and
Firmware version. On the Setup menu, scroll down to highlight Device submenu. Press
Select to enter the Device Submenu. Scroll down to the item you wish to display, and
press Select. Press Menu to return to the previous menu.

71
Figure 58: Device Submenu
Screen Submenu
The Screen submenu allows you to customize settings for Contrast, Rotate, and Always
on. In the Setup menu, scroll down to highlight Screen. Press Select to select the
submenu. Press Menu to return to the previous menu.

72
Figure 59: Screen Submenu
Language Submenu
The Language submenu allows you to select the language you need to use. On the
Setup menu, scroll down to highlight Lang. Press Select to display the screens to select
the submenu. After you select the values, press Select to set the values as displayed
on the screen. Press Menu to return to the previous menu.

73
Figure 60: Language Submenu
USB Submenu
The USB submenu allows you to upload firmware file and download event log or data
log. On the Setup menu, scroll down to highlight USB. Press Select to enter the USB
Submenu. The user will be asked to verify the want to the enter the USB operation and
Configuration Mode. After you select Yes, the system will reboot into the USB operation
and Configuration Mode.
Note: If a USB drive is not present in the USB slot the PDU will enter normal operation.
Note: If you are in USB mode and you want to exit USB mode, you must remove the
USB drive before existing USB mode. Otherwise, the PDU will reboot and re-enter USB
mode.

74
Figure 61: USB Submenu

75
Units Submenu
The Units submenu displays the temperature units. On the Setup menu, scroll down to
highlight Units. Press Select to enter the Units Submenu. After you select the values,
press Select to set the values as displayed on the screen. Press Menu to return to the
previous menu.
Note: This can only be done locally at the PDU.
Figure 62: Units Submenu

76
Alarms Menu
The Alarms menu displays active alarms for the PDU. On the Main Menu, scroll down to
highlight Alarms. Press Select to display the Alarm Screen. When you finish your
review, press Menu to return to the main menu.
Figure 63: Alarms Menu

77
Power Menu
The Power menu manages device, phase, breaker and outlet. On the Main Menu, scroll
down to highlight Power. Press Select. Scroll down to select a submenu and press
Select to display the submenu options. Press Menu to return to the previous menu.
Figure 64: Power Menu

78
Device Submenu
The Device submenu is to display current, voltage and power. On the Power menu,
scroll down to highlight Device. Press Select to display the power values for the entire
PDU. Press Menu to return to the previous menu.
Figure 65: Device Submenu

79
Phase Submenu
The Phase submenu is to display the status of 3-Phase. On the Power menu, scroll
down to highlight Phase. Press Select to display the screens to set the values for the
submenu. After you select the phase, press Select to display the values for that phase
on the screen. Press Menu to return to the previous menu.
Figure 66: Phase Submenu

80
Breaker Submenu
The Breaker submenu is to display power values for the breakers. Press Select to
display the values of the first breaker. To go to the next breaker, Select next. Press
Menu to return to the previous menu.
Figure 67: Breaker Submenu

81
Outlet Submenu
The Outlet submenu is to display voltage, current and power from outlet number 1 to
number n. On the Power menu, scroll down to highlight Outlet. Press Select to display
values for the first outlet. To go to the next outlet, Select next. Press Menu to return to
the previous menu.
Figure 68: Outlet Submenu

Note: Custom outlet names noted in the Web GUI do not make changes to the local
display. This is done to make it easier to map to outlet numbers which can locally be
seen on the outlets themselves.

82
Sensors Menu
The Sensor menu is to display temperature, humidity, door switch, fluid leak etc. On the
Main Menu, scroll down to highlight Sensor. Press Select. This will display the sensor
data for the first sensor. To go to the next sensor, Select next. Press Menu to return to
the previous menu.
Figure 69: Sensors
NOTE: Maximum of 8 sensors are configured per PDU.

83
Section 5 – Daisy Chain Configuration

Daisy-Chain Overview
In daisy chain mode, up to (4) PDUs of the same SKU number, and on the same
Firmware version, can be connected via one IP address. This allows users to gather
information and data on all daisy-chained PDUs from the main PDU. The daisy chain
functionality reduces network cost for PDUs. For example, a standard network switch
used in a data center may contain 24 ports. Without using the daisy chain function, each
port would supply a network connection to one PDU. However, if using the daisy chain
features, a typical network switch with 24 ports can supply network connections for up
to 96 PDUs.
Note: When replacing a Daisy Chained PDU or Accessory, please ‘RESTART’ the
Primary (main) PDU1 controller to re-synchronize the daisy chained PDUs sequence.
This action will not disrupt operations (or outlet states) and can be completed remotely
via Web GUI, SNMP or CLI or physically by pressing and holding the reset button on
the primary controller for 10 seconds (but not more than 15 seconds).
Daisy-Chain Setup
1. After the initial PDU is configured (parent), connect an Ethernet cord from the
PDU Out port on the configured PDU to the PDU In/Serial port on the second
PDU in the daisy chain line.
2. Repeat step 2, connecting PDUs from the PDU Out port to the PDU In/Serial
port for up to 4 PDUs.
Note: The total length of the Ethernet cords connecting the PDUs must be less
than 15m (49 ft.).
3. Go to the Web interface (or management software) to manage and control the
PDUs in the daisy chain.
RNA (Redundant Network Access) Functionality

RNA allows secure access of PDU data and statistics on two separate, private
networks. RNA must be used with a redundant power delivery design including two rack
PDUs for each IT rack. PDUs used in RNA applications must be the same SKU/Part
Number. A maximum of (2) PDU can be used in the RNA convention. See the below
figure for a connection diagram when deploying RNA.

84
Figure 70: Connection Diagram RNA Daisy Chain

How it works:
• Using RNA, the main and expansion unit maintain two separate private networks
that do not overlap.
• RNA works using a redundant power delivery design (two rack PDUs for each IT
rack).
• Each PDU is separately connected to the expansion and main unit’s private
communications network.
• The two PDUs relate to a data communications bus to allow PDUs to share user-
defined information.
Each PDU acts like a main PDU to report PDU data to both networks.
RNA Setup
To set up RNA mode on two PDUs, the user must (1) configure the PDUs for RNA
Mode (using CLI) and then (2) connect the LAN Network cords and Ethernet cords
between PDUs.
To Configure RNA Mode in the CLI

85
1. Log in to the CLI and enter the command ‘dev daisy rna.’
2. The following message will appear:
• Reboot Required for change to take effort.
• System Reboot now, Are you sure? (Y/N).

3. Enter Y to confirm reboot.
4. After reboot, the PDU will be setup to RNA Mode.
5. Repeat this process for the second PDU.
To Connect the PDUs for RNA Setup (see Figure 69)
After the PDUs are configured for RNA:
1. Connect an Ethernet cable from the Landlord LAN Network to the Ethernet port
of the first PDU. This will have limited access/permissions.
2. Connect an Ethernet cable from the Tenant LAN Network to the Ethernet port of
the second PDU. This will have full access to both PDUs.
3. Connect an Ethernet cable from the PDU In/Serial port on first PDU to the PDU
Out port on the second PDU.
4. Connect another Ethernet cable from the PDU Out port on the first PDU to the
PDU In/Serial port on the second PDU.
5. In RNA mode, the default account username is ‘landlord’ and password is
‘12345678’. This account is configured for proper access and control in RNA
mode.
6. To enable this account, login to the CLI with admin credentials.
7. Enter the command ‘dev daisy rna init’.
8. The following message will appear to confirm the landlord account is enabled:
SUCCESS.
9. RNA is now configured and enabled.

86
Power Share
Power Share is designed to allow for continual sensor monitoring and electronic rack
access if one of the 2 power feeds is lost. This feature is available for vertical (0U)
PDUs only. However, due to limited available power from the Panduit iPDU Controller,
power share was designed and tested under the following conditions:
ACF05 or AC06 SmartZone Security Handle, ACF10 (T+D), ACF11 (3T+D).
Care must be taken to not overload the system with accessories as this may cause
instability or power share to become unavailable. Additionally, power share is only
supported by Firmware version 3.x or higher on PDUs with a serial number:
COO: China S/N: > (greater than) CN213N6480

PDU’s manufactured in China after March 22nd, 2021
COO: India S/N: > (greater than) IN21536039

PDU’s manufactured in India after May 3rd, 2021
For complete details on the Serial number please use the Following Guide:
The linked image cannot be displayed. The file may have been moved, renamed, or deleted. Verify that the link points to the correct file and location.

87
The iPDU controller has a maximum output power capacity of 800mA @ 5V = 4 watts.
Based on this, DO NOT deploy the Automatic Light Bar (PN: ACD01) when deploying
solutions leveraging Power Share.
Figure 71: Connection Diagram Power Share & Daisy Chain

To confirm that your controller has Power Share from the Web GUI
Home → Control & Manage → Power Share

88
Enable power share under the edit menu.

89
Section 6 – SmartZone Security Handle

The Panduit Intelligent PDUs allow users to electronically secure and control access to
cabinets. G5 PDU Firmware v3.3.1 (or higher is required). For the latest firmware
please visit: panduit.com → Support → Download Center → PDUs
Note: For security, verify that the handle is seated prior to engaging locking
mechanism. If handle locks prior to handle being properly seated, unlock handle, seat
properly, then lock again. Only users with admin privileges are allowed to make
configuration level changes to the PDU (including Rack Access Security).
Figure 72: SmartZone Security Handles

90
Figure 73: Connection Diagram for SmartZone Security Handle
Note: Specialized sensors were developed for attaching directly to the SmartZone
Security Handle optimizing cable routing.
Use the below table to help count total sensors being deployed.
Part Number Number onboard Device connects to

Sensors
ACF05 2 Panduit G5 PDU
ACF06 2 Panduit G5 PDU
ACF11 4 Panduit G5 Handle
ACF10 2 Panduit G5 Handle
ED001 1 Panduit G5 PDU
EE001 1 Panduit G5 PDU

91
ACA01 1 Panduit G5 PDU
ACC01 1 Panduit G5 PDU
EA001 1 Panduit G5 PDU
EB001 2 Panduit G5 PDU
EC001 4 Panduit G5 PDU
Note: A maximum of 8 sensors can be managed by the Panduit SmartZone G5 PDU

controller.
Configuring Cabinet Access Control

All Rack Access Control configuration can be done under the Rack Access Control
Page from the Web GUI. To access the Rack Access Control Page from the Web GUI,
perform the following steps.
Note: The Hot Aisle or Cold Aisle is selected directly on the electronic handle through a
DIP Switch. This is not a configuration item in the Web Interface.
1. Log into the PDU.

2. Go to the Gear icon > Rack Access Control.

92
Figure 74: Rack Access Control Web GUI
3. The Actions Menu on the right side of the page will allow the user to Add Card,
Rack Access Settings, Handle Settings, Keypad Settings, Remote Control,
Beacon Settings, and Status LED Settings.
Figure 75: Rack Access Control Actions Web GUI

93
Adding a User for Local Rack Access

Every user that needs access to the cabinet needs to have their access card added into
the PDU. Each card (or user) must have a username and either a card ID or keypad
PIN code.
Note: A maximum of 200 cards can be programmed per cabinet. When a user is
added to 1 side of the cabinet, the system automatically allows them access to the
other side (if applicable).
Determining Card ID
To determine the card ID, follow these steps:
1. Place the card near the reader (top of the handle).
2. Go to the event logs on the PDU →
3. Look for the most recent message about an unauthorized card swipe.
Example:
4. The number in the message is the card ID.

Adding a Local access user
1. To add a new card (or user), select Add Card from the Actions menu.

94
Figure 76: Local Rack Access Web GUI
2. Enter a username to identify the user.

3. If the system is configured for RFID Only or Dual Auth, enter the determined card
ID.
Note: In the above example, the card ID is 258563
4. If the system is configured for Keypad Only or Dual Auth, enter the pin.
Note: users must be assigned unique PIN codes in ‘Keypad Only’ mode.
5. If you want to have the card access expire:

a. Select Temporary User
b. Add a Start and Expire time
6. Click Save.
Configuring Rack Access Settings.

The Rack Access Setting are common to the entire system. These include Aisle
Control, AutoLock Time, Door Open Time, and Max Door Open Time.
95
1. To update the rack access settings, select Rack Access Settings from the
Actions menu.
Figure 77: Rack Access Settings Web GUI
2. Select from two options in the Aisle Control.

a. Hot/Cold Combined – Operating hot or cold causes both handles to
open.
b. Hot/Cold Standalone – Operates hot or cold independently
3. The AutoLock Time is the number of seconds after the handle will automatically
lock.
4. The Door Open Time is the number of seconds after the handle alerts door open
5. The Max. Door Open Time is the number of seconds before a critical alarm
announces, door open.
Configuring Handle Settings.

Handle settings and information relate to a specific handle. These include the
Access Control Unit (ACU) name.
1. To update the handle settings, select Handle Settings from the Actions menu.

96
Figure 78: Handle Settings Web GUI
2. Select the handle to edit or get information about.

a. Select the handle you are interested in, Under the PDU section.
3. Enter in the ACU Name. The ACU name is a name to help distinguish the
different handles. This field is alphanumeric and accepts special characters.
4. Work Mode will tell the type of handle connected. For example, RFID only
means the handle has a card reader and no keypad.
5. The Firmware Version, Hardware Version and Serial are read-only attributes
about the handle.
a. Firmware Version is the firmware version running on the handle.
b. Hardware Version is the version of hardware of the handle
c. Serial is the serial number of the handle.
Configuring Keypad Settings

If a SmartZone Security handle with Keypad is deployed; the user has the following
options:

97
1. Card Only: Gain access to cabinet through swiping an authorized card

2. Keypad Only: Gain access to the cabinet through depressing an authorized
secret pin into the keypad:
a. PIN Mode turned on hides the user PIN in the web gui
b. All users must adhere to the same PIN length
c. Users must select unique PIN codes in ‘Keypad Only’ mode.
3. Dual Authentication (Card + Keypad): First swipe an authorized card than within
5 seconds begin depressing an authorized secret PIN into the keypad.
Remote Controlling the Handle.

The remote control will allow you to remotely open and close a handle.
1. To remotely control a handle, select Remote Control from the Actions menu.

98
Figure 79: Remote Control

2. Select the handle to control:
a. Under the PDU section, Select the handle
3. Select the action you wish to perform.
a. Lock remotely locks the handle
b. Unlock remotely unlocks the handle.
4. When finished, click Close.

99
Controlling the Beacon.

The beacon is a visual indicator to give you status of the cabinet at a glance. The
beacon will flash yellow when the cabinet is in a minor alarm or flash red when the
cabinet has a critical alarm. You can also use the beacon’s locate function to flash
the beacon a certain color to easily locate the cabinet. The default state of the
beacon LED is on solid green.
Beacon
Figure 80: Beacon

Beacon LED Table:
Function State Color Purpose

Blue, Green,
Locate Blinking Yellow, Red, Identifies rack location. (customizable)
White, Magenta
Critical
Blinking Red Any critical alarm in the system. (not customizable)
Alarm
Warning
Blinking Yellow Any warning alarm in the system (not customizable)
Alarm
Blue, Green,
Normal
Solid Yellow, Red, Visual indicator on the handle. (customizable)
State
White, Magenta

100
1. To control a handle beacon, select Beacon Settings Control from the Actions
menu.
Figure 81: Beacon Settings Web GUI
2. Select the function of the beacon:

a. Standby –beacon color no alarms
b. Locate –flash beacon
3. Select color for Standby or Locate.
4. Select Save.

101
The Status LED

The SmartZone Security Handle is equipped with a status LED to give a visual
indication of the handle and security status. A summary of all the status LED states can
be seen in the follow table. The default state of the status LED is on solid green.
Status
Status LED Table in Order of Priority:
Status LED Color Description
Standby – Solid (or off) Customer selectable color in standby state. (customizable)
Red - Blinking Blinks three times signaling authentication error (not customizable)
Green - Blinking Lock Open (not customizable)
Key used to unlock

Magenta – Blinking or
Mechanical handle lifted away from base
(not customizable)
Yellow – Blinking Handle open past Door Open Time (not customizable)
Red - Solid Lock open for longer than Autolock Time. (look for obstruction)
(not customizable)
Red - Solid Door open for longer than Door Open Time (door sensor)
(not customizable)

102
Setting Status LED State
1. To set the standby state of the status LED state, select Status LED Settings
from the Actions menu.
Figure 82: Status LED Settings Web GUI
2. Select the color of Status LED when the handle is in standby state.
3. Select Save.
Handle and Compatible Card Types
The table below lists which cards are supported on the different swing handles.
MIFARE® MIFARE MIFARE® HID® HID® EM Output

Classic Plus® DESFire® iCLASS 125kHz 125kHz
1k 2k 4k Prox Prox
ACF05 UID UID UID - CSN CSN Wiegand
ACF06
CSN = Card Serial Number / UID = Unique Identifier

103
Section 7 – SmartZone G5 Accessories

Hardware Overview
The SmartZone G5 accessories are specially designed to interoperate SmartZone G5
iPDU controller. Connecting unapproved sensors to the G5 iPDU controller or
connecting SmartZone G5 Sensors to 3rd party controllers may result in damage.
Monitoring critical attributes (such as temperature, humidity, leak detection, and

intrusion) are all vital aspects of maintaining an efficient-working data center or IT room
atmosphere.
Note: A maximum of 8 sensors can be managed by the Panduit SmartZone G5 PDU

controller. Sensors may be installed with PDUs powered on.
The following table lists available sensors as well as sensor count:
Sensor Description Sensor Count
Temperature Sensor Monitors the temperature in 1

(EA001) the rack.
Temperature + Humidity Monitors the temperature and 2
Sensor (EB001) relative humidity in the rack.
Three Temperature + Monitors the temperature in 4
Humidity Sensor (EC001) three areas using three
separate probes and the
relative humidity using one
probe.
Door Sensor (ACA01) Monitors intrusion when a door 1
on which the sensor is
installed has been opened
greater than 10 mm.
Water - Rope Sensor Monitors leak detection of 1
(ED001) liquid with a resistivity of less
than 2 megaohms (including
distilled water).
Water – Spot Sensor Monitors leak detection of 1
(EE001) liquid with a resistivity of less
than 2 megaohms (including
distilled water) in the
monitored area.

104
Sensor Description Sensor Count
Sensor Port Hub (EF001) Passive hub allowing for three N/A
additional sensors to be
connected.
Leak Detection Sensor Extends the Rope type leak N/A
Extension (EG001) detector by an additional 6m. A
total of four extensions can be
added to the leak detection
sensor for a total length of
30m.
SmartZone G5 Dry Input to the G5 iPDU and 1
Contact Sensor (ACC01) designed to monitor a change
in contact state.
Sensor Sensor
Figure 83: Sensor Ports for Vertical PDU

105
Figure 84: Sensor Ports for Horizontal PDU
Configuring Temperature Scale

To configure the temperature scale (Celsius or Fahrenheit) of the temperature sensors:
1. Go to User Accounts.
b.
Figure 85: User Settings
2. The button at the top of the screen can be used to select Celsius or Fahrenheit.
c.
Figure 86: Celsius Setting
d.
Figure 87: Fahrenheit Setting
Configuring Environmental Sensors
To configure the sensor location, alarms, notifications, and details, open the WEB
Interface:

106
3. Open the Settings.

4. View the Threshold section on the Settings page. Select Threshold to configure
sensors.
5. Go to External Sensors.
6. Select Edit button to configure the desired sensors.
7. In the Edit dialog box, type value of up critical, up warning, low warning, and low
critical.
Select Save to exit the sensor setup.

107
Security
This product contains software that stores user entered data. All data entered by the
user is stored in non-volatile storage on the system running the software.
Non-volatile Storage
• The G5 iNC Controller uses non-volatile storage on the G5 PDU to store all
configuration information.
Authentication Data
• Usernames are stored in non-volatile memory and are available to ‘administrator’
role users, for the purpose of managing access to the system.
• Passwords used for managing the software are stored in non-volatile storage.
• SNMP v1/v2c community strings are stored in non-volatile storage.
• SNMP v3 usernames and passwords are stored in non-volatile storage.
Network Transport Security

• The product comes with a default SSH RSA 1024-bit private host key.
• The product comes with a default RSA 2048-bit private key and certificate.
• The user may upload a custom HTTPS certificate and private key.
o The HTTPS certificate should use a SHA-256 signature.
o The private key should be RSA 2048-bit.
o Other private key types may work, but performance may be negatively
impacted if greater private key sizes are used: RSA 3072-bit, RSA 4096-
bit.
• The product uses TLS 1.2 to communicate with HTTPS web browser clients.
• The product provides a SSH server with these algorithms to communicate with
SSH clients:
o Key exchange algorithms: diffie-hellman-group14-sha1
o Host key algorithms: ssh-rsa
o Encryption algorithms: aes256-ctr
o MAC algorithms: hmac-sha1
Network Configuration Data

• Network Configuration, including Static IP addresses and addresses obtained by
DHCP are exposed on an “Identification” page and on a Network Configuration
page, to aid in network management of the product.

108
• The product implements an internal authentication mechanism, authorization

events generate “Event Logs” containing the IP address and username of
successful logins, and the IP address of failed logins for valid usernames.
External Authorization Mechanisms

• LDAP & Radius – username & password are stored in non-volatile storage.
• LDAP is not encrypted over the network.
• The remote LDAP server authenticity (fingerprint) is not validated.
• The Radius protocol is designed to only transmit hashed and obfuscated
passwords over the network.
Other Features
• The product includes a real-time clock and a capacitor that maintains time for a
short amount of time when no power is applied. When combined with NTP,
accurate timestamps on logs are provided.

109
Warranty and Regulatory Information

Warranty Information
(http://www.Panduit.com)
Regulatory Information
Safety and regulatory compliance
For important safety, environmental, and regulatory information, see Safety and
Compliance Information at the Panduit website (http://www.Panduit.com)

110
Panduit Support and Other Resources

Majority of your support needs can be met by visiting Panduit.com and navigating to the
respective product page. If you require additional assistance; we are here to help.
Accessing Panduit Support
North America Europe / Middle East
Customer Service Customer Service

• Price & Availability • Price & Availability
• Expedites • Expedites
800-777-3300 or cs@panduit.com 0044-(0)208-6017219 or EMEA-
CustomerServices@panduit.com
PDU Technical Support: PDU Technical Support:

• PDU Selection
• PDU Selection
• Competitor Cross references
• Competitor Cross references
• Product Documentation
• Product Documentation
Email: TechSupportEMEA@panduit com
E il T hS t@ d it
https://www.panduit.com/en/support/contact-us.html
Global PDU System Support:

• Firmware Updates
• Bulk Configuration
DCIM Software Support
Email: systemsupport@panduit.com
Phone: 1-866-721-5302

111
Acronyms and Abbreviations

A LCD Liquid-Crystal Display
Amps/Amperes LDAP
AC Lightweight Directory Access Protocol
Alternating Current OLED
AES Organic Light-Emitting Diode
Advanced Encryption Standard PDU
CLI Power Distribution Unit
Command Line Interface QNA
DHCP Quad-Network Interface
Dynamic Host Configuration Protocol RNA
Gb Redundant Network Interface
Gigabyte SHA
GUI Secure Hash Algorithms
Graphical User Interface SNMP
IP Simple Network Management Protocol
Internet Protocol TCP/IP
kVA Transmission Control Protocol/Internet

Protocol
Kilo-Volt-Ampere
USB Universal Serial Bus
kW
V Volts
Kilowatts
W
kWH Kilowatt Hour
Watts
LAN Local Area Network

109
Appendix A: Sensor Configuration

Door Switch Sensor
Door Switch Sensor is designed to send an alarm or notification signal when the door
on which it is installed had been opened more than 10mm. This provides added
security. The door switch can be configured to alert when the door is opened, alert
when the door is closed, or the alerts can be disabled.
Figure 88: Door Switch Sensor Configuration
Note: The Door Switch Sensor is only designed to connect to a Panduit PDU.
Connecting it to another device may result in damage.
Dry Contact Input Sensor (side panel switch)

The dry contact sensor can be configured to alert when the when the contact is opened,
alert when the contact is closed, or the alerts can be disabled.

110
Figure 89: Dry Contact Cable
Note: The dry contact cable is only designed to connect to a Panduit PDU. Connecting
it to another device may result in damage.
Temperature & Humidity Sensors

Temperature and humidity sensors are designed to add comprehensive
environmental monitoring to any Panduit PDU. The temperature and humidity sensors
can be configured with upper critical, upper warning, lower warning and lower critical
threshold levels. Each alarm can also be disabled.
SMARTZONE UPS USER MANUAL

111
Figure 90: Temperature and Humidity Sensors

Configuring Environmental Sensors
Each SmartZone G5 Intelligent PDU features an onboard controller capable of
managing a maximum of 8 sensors.
To configure the sensor location, alarms, notifications, and details, open the WEB
Interface:
8. Open the Settings.

9. View the Threshold section on the Settings page. Select Threshold to configure
sensors.
10. Go to External Sensors.

112
11. Select Edit button to configure the desired sensors.

12. In the Edit dialog box, type value of up critical, up warning, low warning, and low
critical.
13. Select Save to exit the sensor setup. Repeat this process for additional sensors.
Sensor Port
Sensor Port
Figure 91: Sensor Ports on controller

113
Appendix B: Firmware Upgrade Options

The firmware upgrade procedure verifies the image by validating the signature of the
images. If the signature does not match, the firmware upgrade procedure will ignore the
image and remain on the current version. Updating the firmware does not affect the
configuration or outlet state of the intelligent PDU.
Web Interface Method

1. Open the User interface in a web browser by entering the PDU IP address.
2. Login to with Administration credentials.
3. Go to Settings > System Management > Actions > Update Firmware.
4. In the Firmware Update dialog box, browse to (*.FW) firmware file.
Figure 92: Upload Firmware
NOTE: the firmware file name must be retained AS IS.
5. Select Upload. The system will update the newest firmware to the Intelligent
Network Controller.
6. When the upload is finished, the system will reboot automatically.
G5 Upgrade Utility (GUT)

Bulk management of PDU is available using the G5 Upgrade Utility. See Appendix
C for details.

114
NOTE: the firmware file name must be retained AS IS.
1. Select Upload. The system will update the newest firmware to the Intelligent
Network Controller.
USB Method
Note: Verified to work with ToshibaTM or SandiskTM up to 16GB USB Drives. Others
USB drives may work as well.
1. Save the Firmware file (‘*.FW’) to a USB drive.

2. Insert the USB drive into the USB port of the Network Controller.
3. Enter USB mode on the PDU: Press Select. Go to Setup>USB>Yes. Select Yes
to confirm entering USB mode.
4. Select F/W Up>Yes to upload the new Firmware.
5. The OLED will show the Firmware update progress.
6. When the update is complete, remove the USB.
7. From the USB Menu, select Quit to exit USB mode. Select Yes to confirm exit.
8. The PDU will automatically reboot.
9. To confirm that the Firmware was uploaded successfully, go to
Setup>Device>Firmware.
FTPs Method
To access a PDU using a FTPs program, FTPs must be enabled through the PDU Web
Interface or CLI. In the Web Interface, go to Network Settings >SSH/FTPs
Configuration. Select the check box to enable FTPs Access. In the CLI, login as an
administrator and use the command net tcpip FTPs open
1. Login to a FTPs program with a role with administration privileges.

2. Transfer the updated *FW file to the root directory. Close the FTPs.

115
3. Connect to the PDU via SSH using a program such as HyperTerm or PuTTY.
4. Login using a role with administration privileges.
5. Enter the command sys upd all.
6. It will show the message: System will enter upgrade mode after reboot, System
Reboot now, Are you sure? (Y/N).
7. Enter Y.

116
Appendix C: Bulk Management of PDUs

A dedicated G5 Upgrade Tool (GUT) is included with every firmware release. This
utility enables a user to bulk manage PDUs. This utility features Firmware Upgrading,
Configuration Replication (common parameters) and management of uncommon
parameters (.csv) file. Requires Windows OS.
G5 Upgrade Tool (GUT)

1. Firmware Upgrade
a. Insert IP address or IP address range in the Scan Network Tab
b. Insert admin credentials
c. Click ‘Start Upgrade’
Figure 93: G5 Upgrade Tool Interface
Note: Simplify firmware upgrade from 2.x to 3.x using this utility down to a
single click.
2. Configuration Replication of Common Parameters
a. Pre-set the common parameters (e.g. thresholds, rack access control,
etc..) via the Web GUI and download configuration (conf.ini) from the
System Management menu.

117
Figure 94: System Management Screen Web GUI
b. Insert IP Address or Range of the target PDU(s)

c. Insert admin credentials
d. Load the confi.ini file to the G5 Upgrade Utility and click Start Conf.ini
3. Configuration Replication of Un-Common Parameters

a. Insert IP Address or Range of the target PDU(s)
b. Insert admin credentials
c. Edit and Save the .csv file.

118
Figure 96: Example CSV File

d. Load the Config.csv file to the G5 Upgrade Utility and click Start
Config.csv

119
Appendix D: System Reset or Password Recovery

Use Reset Button on Controller
Press and hold the Reset Button for 8 seconds to recover from an Intelligent Network
Controller communication failure. This will cause a reset of the iNC controller, all
configuration(s) will be retained.
To Default the controller to factory settings, press and hold the Reset Button for at least
20 seconds. This will cause a reset of the iNC controller erasing all existing
configurations, including username(s) and password(s). It does not change the Energy
(kWh) value and does not affect the outlet state.

120
Appendix E: PDU Alarms

PDU Unit Active Power Above upper
critical
PDU Unit Active Power Above upper
warning
PDU Unit
PDU Unit Active Power Below lower
warning
PDU Unit Active Power Below Lower
critical
Input Phase X Voltage Above upper
critical
Input Phase X Voltage Above upper
warning
Input Phase X Voltage Below lower
warning
Input Phase Input Phase X Voltage Below lower critical
Input Phase X Current Above upper critical
Input Phase X Current Above upper
warning
Input Phase X Current Below lower
warning
Input Phase X Current Below lower critical
Circuit Breaker X Current Above upper
critical
Circuit Breaker X Current Above upper
warning
Circuit Breaker X Current Below lower
Circuit Breaker warning
Circuit Breaker X Current Below lower
critical
Circuit Breaker Status ON
Circuit Breaker Status OFF
Outlet X Active Power Above upper critical
Outlet X Active Power Above upper
warning
Outlet
Outlet X Active Power Below lower
warning
Outlet X Active Power Below lower critical

121
Outlet X Immediate ON
Outlet X Delayed ON
Outlet X Immediate OFF
Outlet X Delayed OFF
Outlet X Immediate REBOOT
Outlet X Delayed REBOOT
Outlet X Cancel Pending Command
External Sensor X (numerical) Above
upper critical
External Sensor X (numerical) Above
upper warning
External Sensor X (numerical) Below
External Sensor lower warning
External Sensor X (numerical) Below
lower critical
External Sensor X (state) Alarmed
External Sensor X (state) Communication
Lost
System Event log Cleared
System Data log Cleared
System PDU configuration file Imported
System PDU configuration file Exported
System Firmware update completed
System Firmware update failed
System Firmware update started
System Firmware Validation failed
System
System an LDAP error occurred
System Network interface link state is up
System Sending SMTP message failed
System Intelligent Network Controller reset
System Intelligent Network Controller start
System Communication Lost
Daisy Chain state changed
USB Port
User Activity User X Authentication failure
User Activity User X User logged in
User Activity
User Activity User X Session timeout
User Activity User X User blocked

122
User Administration Password changed

User Administration Password settings
changed
User Administration
User Administration User added
User Administration User deleted
User Administration User modified
Smart Rack Access Door Open
Smart Rack Access Door Closed
Smart Rack Access
Smart Rack Access User Card Swiped
Smart Rack Access Door Autolocked
Trap Codes assigned to Alarms List
Trap codes assigned for critical alarms:
Trap Class Trap Code Trap Description
Critical 1 The PDU unit active power is ABOVE critical threshold value.
2 The PDU unit active power is BELOW critical threshold value.
3 The Critical Energy Alarm.
4-6 The phase (1-3) voltage is ABOVE critical threshold value.
7-9 The phase (1-3) voltage is BELOW critical threshold value.
10-12 The phase (1-3) current is ABOVE critical threshold value.
13-15 The phase (1-3) current is BELOW critical threshold value
16-27 The circuit breaker (1-12) current is ABOVE critical threshold

value
28-30 The circuit breaker (1-12) current is BELOW critical threshold

value
40-51 The circuit breaker (1-12) is in OFF state
52-99 The outlet (1-48) active power is ABOVE critical threshold

123
value
100-147 The outlet (1-48) active power is BELOW critical threshold

value
148-155 The sensor (1-8) temperature/humidity is ABOVE critical

threshold value
156-163 The sensor (1-8) temperature/humidity is BELOW critical

threshold value
164-171 The sensor (1-8) contact state is in alarm.
172-179 The sensor (1-8) lost communications.
183 User authentication failed.
186 Power or relay communication lost to main board
187-189 Input Phase (1-3) Frequency Asserted below lower critical.
193 Firmware update failed.
194 Failure in sending the SMTP message.
195-197 Input Phase (1-3) Frequency Asserted above upper critical
Trap codes assigned for warning alarms:
Trap Class Trap Trap Description

Code
Warning 200 The PDU unit active power is ABOVE warning threshold
value.
201 The PDU unit active power is BELOW warning threshold

value.
202 The PDU warning energy alarm.

124
203-205 The phase (1-3) voltage is ABOVE warning threshold value.
206-208 The phase (1-3) voltage is BELOW warning threshold value.
209-211 The phase (1-3) current is ABOVE warning threshold value.
212-214 The phase 1 current is BELOW warning threshold value.
215-226 The circuit breaker (1-12) current is ABOVE warning

threshold value.
227-238 The circuit breaker (1-12) current is BELOW warning

threshold value.
239-250 The circuit breaker (1-12) is in OFF state.
251-298 The outlet (1-48) active power is ABOVE warning threshold

value.
299-346 The outlet (1-48) active power is BELOW warning threshold

value.
347-354 The sensor (1-8) temperature/humidity is ABOVE warning

threshold value.
355-362 The sensor (1-8) temperature/humidity is BELOW warning

threshold value.
Trap codes assigned for information alarms:

Code
Informational 380-391 The circuit breaker (1-12) is in ON state.
392-439 The outlet (1-48) IMMEDIATE ON occurred.
440-487 The outlet (1-48) DELAYED ON occurred.
488-535 The outlet (1-48) IMMEDIATE OFF occurred.

125
536-583 The outlet (1-48) DELAYED OFF occurred.
584-631 The outlet (1-48) IMMEDIATE REBOOT occurred.
632-679 The outlet (1-48) DELAYED REBOOT occurred.
680-727 The outlet (1-48) Cancel Pending Commands occurred.
728-735 The sensor (1-8) contact state is in cleared.
740 Event log Cleared.
741 Data log Cleared.
742 PDU configuration file Imported.
743 PDU configuration file Exported.
744 Firmware update completed.
745 Firmware update started.
746 An LDAP error occurred.
747 Network interface link state is up.
748 Communication Module reset.
749 Communication Module start.
750 Daisy Chain state changed.
752 User xxx logged in.
753 User xxx session timeout.
754 User xxx blocked.
755 User xxx password changed.
756 User password settings changed.
757 User xxx added.
758 User xxx deleted.

126
759 User xxx modified.
761 Smart Rack Access Door Opened
762 Smart Rack Access Door Closed
763 Smart Rack Access User Card Swiped
764 Smart Rack Access Door Autolocked
765 Smart Rack Mechanical Lock
766 Smart Rack Mechanical Unlock
Trap codes assigned for information alarms:

Code
Clear 770 The PDU unit active power is alarm clear.
771 The PDU energy alarm clear.
772-774 The phase (1-3) voltage alarm cleared
775-777 The phase (1-3) current alarm cleared
778-789 The circuit breaker (1-12) current alarm cleared
790-837 The outlet (1-48) active power current alarm cleared.
838-845 The sensor (1-8) temperature/humidity alarm cleared.
846-853 The sensor (1-8) lost communication alarm cleared.
854-856 Input Phase (1-3) Frequency Deasserted above upper

critical
857-859
Input Phase (1-3) Frequency Deasserted below lower
critical.

127
Trap codes assigned enhanced security alarms:
Trap Class Trap Code Trap Description
Warning 1100 Door Open for longer than configured door time out
Critical 1101 Door Open for longer than configured max door open time
Informational 1102 Door unlocked with authorized pin code
1103 Door accessed with unauthorized pin code.
1104 Door locked because opposite aisle locked.
1105 Door opened because opposite aisle unlocked.
1106 Temporary user expired and was removed.
1108 User added
1109 User modified
1110 User deleted.
Trap codes assigned for Phase Power alarms:
Trap Trap Code Trap Description

Class
1121-1123 Input Phase Measurement Active Power of PHASE (1-3) asserted
Critical above upper critical
1124-1126 Input Phase Measurement Active Power of PHASE (1-3) asserted

below lower critical
Input Phase Measurement Apparent Power of PHASE (1-3)

1127-1129
asserted above upper critical

1130-1132
asserted below lower critical
Warning

128
Input Phase Measurement Active Power of PHASE (1-3) asserted

above upper warning
1133-1135
Input Phase Measurement Active Power of PHASE (1-3) asserted
below lower warning
1136-1138

asserted above upper warning
1139-1141

asserted below lower warning
1142-1144
Cleared Input Phase Measurement Active Power of PHASE (1-3)

1145-1147 deasserted above upper critical/below lower critical/above
upper warning/below lower warning

deasserted above upper critical/below lower critical/above
1148-1150
upper warning/below lower warning
Role Added by Admin User

1151
Role Deleted by Admin User

1152
Role Modified by Admin User

1153

129
Appendix F: Panduit Network Controller Replace

or Rotate 180°
1. Use a T10 Torx screwdriver on the screws as shown in Figure 98. The screws
are held in with retaining washers.
Figure 98: Screws on Network Controller
a. Controller may be rotated to accommodate overhead or underfloor power. If

rotating controller, YOU MUST DISCONNECT the ribbon cable to prevent
damage to the ribbon cable. After rotating the controller, carefully reconnect
the ribbon cable making sure to not pinch any of the ribbon cable.
2. If replacing controller, disconnect the existing ribbon cable from the existing
controller. To reinstall, carefully connect the ribbon cable to the new controller
making sure to not pinch any of the ribbon cable.

130
Ribbon Cable
Figure 99: Ribbon Cable for the Network Controller
3. Replace and tighten the two (T10) screws on the Intelligent Network Controller to
2.2 – 3.1 lbf-in (0.25 – 0.35 N-M). Overtightening the screws may result in metal
deformation.

131
Appendix G: Direct connect to the PDU by

Changing Your PC’s IP Address
Note: Instructions refer specifically to Windows 10. Please refer to your operating
system documentation if you are not using Windows 10.
1. Type control into Windows Search and select Control Panel.
Figure 100: Control Panel

132
2. In the Control Panel window, select View network status and tasks under the
Network and Internet heading.
Figure 101: Network Status and Tasks
3. Select Change adapter settings from the menu on the left.

133
Figure 102: Change Adapter Settings
4. Right-click Ethernet and select Properties.
Figure 103: Properties

134
Figure 104: Ethernet Properties
5. Select Internet Protocol (TCP/IP) Version 4 (you may need to scroll down).
Then click the Properties button.

135
Figure 105: Internet Protocol Version 4
6. Select the Use the following IP address radio button. The Use the following
DNS server addresses radio button then selects automatically.

136
Figure 106: IP Settings for Direct Connection
Enter the following details into the appropriate boxes:
• IP address: 192.168.0.10
• Subnet mask: 255.255.255.0
• Default gateway: 192.168.01
• Preferred SNS server: 192.168.0.1
7. Click OK to accept the entries.

8. Connect the PDU network connection directly to the PC’s Ethernet card using a
patch cable.
9. Power the PDU unit.
10. Open a web browser on the PC.
11. Enter the address bar http://192.168.0.1 into your browser.

137
Appendix H: Command Line Interface (CLI)

The Command Line Interface (CLI) is an alternate method used to manage and control
the PDU status and parameters, as well as basic admin functions. Through the CLI a
user can:
• Reset the PDU
• Display PDU and network properties
• Configure the PDU and network settings
• Switch outlets on/off
• View user information
Connecting to the CLI requires a terminal emulation program such as HyperTerminal or

PuTTY
Supported Commands
The PDU CLI command set for managing and monitoring the PDU includes the
following commands:
• ? command: PDU help query
• sys command: PDU system configure and setting
• net command: PDU net application configure and setting
• usr command: PDU user operation
• dev command: PDU device setting
• pwr command: PDU power setting

NOTE: Command variables are represented in command input syntax surrounded by
angle braces (< >). Optional parameters are represented in command input syntax
surrounded by straight brackets ([ ]). For data of type array, the 'x' character as index of
array in command input syntax means all indexes. You must be logged into the PDU
before commands can be sent. See below for a list of all CLI commands.

138
Connecting to the CLI through the serial interface

An option to communicating through the serial interface is to use the specialized YOST
Serial Data Cable Panduit Part Number: MA017. This cable Remaps Panduit G5 Serial
Interface to a YOST interface.
PDU In/Serial for CLI
Figure 107: Connect MA017 to the PDU In/Serial port
To connect the PDU to a computer (via Serial Interface):

Using a MA017 YOST Remap cable and a Cisco Compatible Console Cable (USB to
RJ45) insert the USB End to an available port of the computer.
Logging in with HyperTerminal

To login through HyperTerminal, set the COM settings to the following parameters:
• Bits per second: 115200

139
• Data bits: 8
• Parity: None
• Stop bits: 1
• Flow control: None
Serial Cable Pinout to Create Your Own Cable

Optionally if you prefer to make your own RJ45-to-DB9 Serial cable, the connections
are wired as shown:
Figure 108: Serial Cable Pinout

Logging in with SSH via PuTTY
1. Ensure SSH has been enabled: On GUI, go to Device Configuration > Network
Service > SSH. Select the Enable SSH Access checkbox. Select OK.
2. Open an SSH client (PuTTY).
3. Enter the IP address in the Host Name field. Select the connection type: SSH
• For SSH, enter 22 in the Port field.

4. Select Open.
5. Enter your Username. Press Enter.
6. Enter your password. Press Enter.
7. You are now logged into the SSH. Refer to the CLI Commands table below for
available commands.
NOTE: SSH connection is not available when serial connection is enabled.

140
CLI Commands
Help Commands
Command Description Example
Panduit>?
sys PDU system

Panduit>? List all available PDU CLI configure and setting.
commands.
net PDU net application
configure and setting.
usr PDU user operation.
dev PDU device setting.
pwr PDU power setting.
System Commands
sys date [year-month-day] Query or set system’s Panduit>sys date 2013-09-

date. 19
SUCCESS
Panduit>sys date
SUCCESS
Date: 2013-09-19
Time: 03:49:46
sys time [hour:min:sec] Query or set system’s Panduit>sys time
time. Panduit>sys time 14:35:34
sys ntp <IP Address> Synchronize system date >sys ntp 69.25.96.13
and time, with ntp server NOTE: IP Address must be a
you set. valid ntp, server address
otherwise, executes, failed

141
sys ver Query system’s version Panduit>sys ver

information including SUCCESS
firmware, bootloader, and Firmware version: 3.19
Web. Bootloader version: 2.10
LANGUAGE version: 3.01
WEB version: 6.30
sys def Recover PDU to default Panduit>sys def
configuration. SUCCESS
Recover
Press any key to cancel
sys rst Reset system. Panduit>sys rst
Reboot required for change
to take effort.
System Reboot now, Are you
sure? (Y/N):Y
sys upd all Update system’s firmware Panduit>sys upd lan
with existing pdu bin file. SUCCESS
system will enter upgrade
mode after reboot
sure? (Y/N):Y
NOTE 1: There must be a

valid file named Panduit.fw
existing in root directory.
NOTE 2: If in daisy chain
configuration, main PDUs will
upgrade all daisy chain
firmware.
sys upd boot Update system’s Panduit>sys upd boot
bootloader. SUCCESS
mode after reboot
sure? (Y/N):Y

142
NOTE 1: There must be a

valid file named boot.bin
existing under directory/fw.
NOTE 2: If in daisy chain
configuration, main PDU will
also upgrade its all PDUs in
daisy chain.
sys upd conf Update system’s Panduit>sys upd conf
configuration. SUCCESS
mode after reboot
sure? (Y/N):Y
NOTE: There must be a valid

file named conf.ini existing
under directory/fw.
sys log del event Delete event log file. Panduit>sys log del event,
SUCCESS
sys log edit data [on Configure data log PANDUIT>sys log edit data
<interval> | off] collection parameters on 1
SUCCESS
PANDUIT>sys log edit data
off
SUCCESS
sys log del data Delete data log file. Panduit>sys log del data,
SUCCESS
Panduit>
sys dualinput set Setting the Region for the Panduit> sys dualinput set
<na | emea> Dual rated PDUs Power na
Capacity. SUCCESS
sure? (Y/N):Y

143
Network Commands
net ssh [on/off] Query or on/off SSH. Panduit>net ssh

SUCCESS,
SSH Port: 22
SSH Server is running
Panduit>net ssh on
SUCCESS
Panduit>net ssh off
SUCCESS
net ftps [on/off] Query or on/off FTPs. Net ftps
SUCCESS
FTPS Port: 21
Service is running
Is Ftps
net http [on/off] Query or on/off net http. Panduit>net http
SUCCESS,
HTTP Port: 80
HTTPS Port: 443
WEB Protocol: HTTP
Panduit>net http off
E801
WEB protocol is changed,
Please reboot to validate
System Reboot now, Are
you sure? (Y/N):Y
net mac Query MAC address. Panduit>net mac
SUCCESS
MAC Addr: C8-45-44-66-
2B-26
net tcpip Query network's IP Panduit>net tcpip
information. SUCCESS
IPv4 Addr: 192.168.30.39
net tcpip <dhcp> Set network to dhcp mode. Panduit>net tcpip dhcp
SUCCESS
Network is reconfigured,

144

you sure? (Y/N): Y
net tcpip <static ip, mask, Set static IP, mask and Panduit>net tcpip static
gateway> gateway. 192.168.30.39
255.255.255.0
192.168.30.1
SUCCESS
Network is reconfigured,
you sure? (Y/N): Y
User Commands
User List List all users account Panduit>usr list
existing. SUCCESS
Usr Role
-------------------------
admin admin
user user
User unlock<username> Unlock specified user. Panduit>usr unlock user
SUCCESS
Panduit>usr unlock admin
SUCCESS
NOTE: 1. Account would

be locked temporarily if
login failure excess
“Maximum number of
failed logins”. Use this
command to unlock it.

145
Device Commands
dev usb [on|off] Query or on/off USB. Panduit>dev usb

Panduit>dev usb off
Panduit>dev usb on
dev daisy [rna|qna] Query or set daisy chain Panduit>dev daisy
mode. SUCCESS
daisy chain unit number: 1
daisy chain address list:
000
Daisy Mode: RNA
Panduit>dev daisy qna
SUCCESS
you sure? (Y/N): N
dev daisy <rna|qna> init Initialize daisychain. Panduit>dev daisy qna init
SUCESS
you sure? (Y/N):N
dev hid <PDUID> <hot | Remote locking and PANDUIT>dev hid 1 cold
cold> <lock | unlock> unlocking the cabinet. unlock
SUCCESS
dev outlet <PDUID> status Query all outlets' status Panduit>Dev outlet 1
with specified PDUID. status
SUCCESS
Relay Outlet Status
Outlet#1: Close Outlet#2:
Close Outlet#3: Close
Outlet#4: Close
Outlet#8: Close
Outlet#12: Close
NOTE 1: For M pdu, this

command is in valid.

146
NOTE 2: PDUID index

from 1; if in daisy chain,
the master's PDUID is 1,
others is ,2,3,
dev outlet <PDUID> Query or set specified Panduit> dev outlet 1 1 off
<outlet index> [on|off] PDUID and outlet-index's SUCCESS
outlet status.
NOTE: For Monitored
PDUs, this command is
invalid.
dev sensor List all sensors equipped. Panduit> dev sensor
SUCCESS
Sensor count 4
------------------------
Name Type, SN Value
-------------------------
T1,TEMP 012345678 27.5
T3,TEMP 012345678 27.2
T2,TEMP 012345678 27.3
RH HUMI 012345678 44
dev ver <slipaddr> Query Panduit> dev ver 1
sensor/power/delay's Panduit> dev ver 15
firmware version. Panduit> dev ver 35
NOTE: relay: start from 1

power: start from 15
sensor: start from 35
Power Commands
pwr unit [idx] Query device information, Panduit> pwr unit

Query specified index SKU: P9S20A , , , ,
unit’s electric information. Serial: , , , , ,
FuncType: PDU Monitored

147
Rating :220-240V, 16A,

3.5-3.8kVA, 50/60Hz
Mac :C8:45:44:66:2B:26
Tcpip :192:168:30:38
Panduit>pwr unit 1
SUCCESS
PDU UNIT 1 power
Feature
voltage: 0V
current : 0.0A
active power: 0W
apparent power: 0W
power factor: 0.00
energy: 0.000kWh
pwr phase <idx> Query specified phase’s Panduit> pwr phase 1
electric information. SUCCESS
PDU PHASE 1 power
Feature
voltage: 0V
current : 0.0A
active power: 0W
apparent power: 0W
power factor: 0.00
energy: 0.000kWh
pwr cb <idx> Query specified circuit Panduit> pwr cb 1
breaker’s SUCCESS
Electric information. PDU CB 1 power Feature
voltage: 0V
current : 0.0A
active power: 0W
apparent power: 0W
power factor: 0.00
energy: 0.000kWh
pwr outlet <idx> Query specified outlet’s Panduit> pwr outlet 1
electric information. SUCCESS
PDU OUTLET 1 power
Feature

148
voltage: 0V
current : 0.0A
active power: 0W
apparent power: 0W
NOTE: For Monitored

PDUs, this command is
invalid.

149
Appendix I: RADIUS Server Configuration

To allow users to login as the admin User-Role
This example demonstrates how to configure freeradius with users that can login as the
admin User-Role. It assumes a clean installation of freeradius on Ubuntu or and
equivalent installation.
1. Install freeradius or start with a pre-existing installation.
2. Create authorized client configuration statements in
/etc/freeradius/3.0/clients.conf that are configured for your security
requirements.
3. Create a dictionary at /usr/share/freeradius/dictionary.Panduit containing:
# -*- text -*-
VENDOR Panduit 19536
BEGIN-VENDOR Panduit
ATTRIBUTE User-Role 1 integer
VALUE User-Role User 1
VALUE User-Role Admin 2
END-VENDOR Panduit
4. Load dictionary.Panduit by appending the following line to
/etc/freeradius/3.0/dictionary:
$INCLUDE /usr/share/freeradius/dictionary.Panduit
5. Add authorized users to /etc/freeradius/3.0/mods-config/files/authorize with the

desired role. (Note: the ‘users’ file location may vary based on unique
customizations or different package managers.) When specified, the User-Role
MUST be the first attribute of the user. Use passwords that are configured for
your security requirements.
a. User-Role is not specified: (This user logs in as the default “user” Role)
raduser Cleartext-Password := "23456789"
Service-Type = 1
b. User-Role is set to Admin: (This user logs in as the “admin” Role)

radroleadmin Cleartext-Password := "34567890"
User-Role = Admin,
Service-Type = 1
c. User-Role is set to User: (This user logs in as the “user” Role)

radroleuser Cleartext-Password := "45678901"
User-Role = User,
Service-Type = 1
6. If you started with a clean install of freeradius, you may need to configure these

150
options to enable authentication in /etc/freeradius/3.0/radiusd.conf: (make sure

they are configured for your security requirements)
auth_badpass = yes
auth_goodpass = yes
auth = yes
7. Restart the RADIUS server for the configuration changes to take effect.
systemctl stop freeradius
systemctl start freeradius
8. Verify the server is able to perform authentication and returns the configured
User-Role. Note: You may need to change this example based on any client
restrictions that are enforced.
Usage: radtest [OPTS] user passwd radius-server[:port] nas-port-number secret
# radtest 'radroleadmin' '34567890’ 192.0.2.1 0 'panduit#1' ''

Sending Access-Request of id 212 to 192.0.2.1 port 1812
User-Name = "radroleadmin"
User-Password = "34567890"
NAS-IP-Address = 127.0.1.1
NAS-Port = 0
Message-Authenticator = 0x00000000000000000000000000000000
rad_recv: Access-Accept packet from host 192.0.2.1 port 1812, id=212, length=38
User-Role = Admin
Service-Type = Framed-User

151
Appendix J: Panduit G5 Accessories

Accessory P/N Accessory Description
EA001 SmartZone G5 Temperature Sensor
EB001 SmartZone G5 Temperature + Humidity Sensor
EC001 SmartZone G5 (3) Temperature + Humidity Sensor
ED001 SmartZone G5 Liquid Rope Sensor
EE001 SmartZone G5 Liquid Spot Sensor
EF001 SmartZone G5 (3) Sensor Hub
EG001 SmartZone G5 Liquid Rope Extension
ACA01 SmartZone G5 Door Switch (magnetic 2 piece)
ACC01 SmartZone G5 Dry Contact Input
ACD01 SmartZone G5 USB Light Strip
ACF05 SmartZone Security Handle with Integral Humidity Sensor
ACF06 SmartZone Security Handle with Integral Humidity Sensor and Keypad
ACF10 Temperature and Door Sensor; connects to SmartZone Security Handle. (Rear)
(3) Temperature and Door Sensor, connects to SmartZone Security Handle
ACF11 (Front)
ACF20 SmartZone Security Handle Patch Cord (JST to RJ45 Male)
MA030 SmartZone Security Handle Patch Cord (RJ45 Female to RJ45 Male)
MA031 Panduit PDU Power Share Patch Cord (RJ45 Male to RJ45 Male)
MA005 Panduit PDU Controller
MA017 Category 6, PDU YOST Serial Data Cable Assembly
CRD-02-10PK SmartZone Security Handle HID CARDS 125 KHZ (10 PACK)
CRD-03-10PK SmartZone Security Handle HID CARDS 13.56 MHZ (10 PACK)
TU020X Base Tumbler for Key KE020X, for ACF05, ACF06
TU021X Option 1 Tumbler for Key KE021X, FOR ACF05, ACF06
KE020X Base Key for Tumbler TU020X
KE021X Option 1 Key for Tumbler TU021X
Note: Panduit SmartZone G5 PDU Controller can handle a maximum of 8 sensors. Some part numbers
have multiple sensors built in (e.g. EC001 has 4 sensors, ACF05 or ACF06 has 2 sensors).

152
Appendix K: Compliance Model Number Details

PP#&*%%-XXXX, where:
XXXX: Series number. Shown different outlet combination
%%: Input Current. 16 means 16A
*: Form 0:0U 1:1U 2:2U
&: Power Input: 1: 200-240Vac, 1 phase
2: 200-240/346-415 Vac (Wye), 3 phase
3: 100-120Vac, 1 phase
4: 200-240Vac (Delta), 3 phase
5: 100-240Vac, 1 phase
6: 120-208Vac (Wye), 3 phase
#: Different management feature.
0: Basic PDU
1: Metered iPDU
2: Metered, Outlet switched iPDU
5: Outlet Metered iPDU
6: Outlet Metered, Outlet switched iPDU

153
Appendix L: JSON API Web Service

This API enforces constraints on certain JSON types:
• Objects: may only be nested one level in a resource or 2 levels in a resource

collection.
• Numbers: must be within the range and precision defined by the property.
• Strings: must not exceed the maximum (encoded) length defined by the
property AND must contain only ASCII printable characters, except where
noted. Some strings have a no space requirement or special format
requirement.
• Arrays: must not be nested and must contain delimited strings or primitive
numbers.
General PDU Limitations:
• String encoded tabs, backspaces, form feeds and Unicode are not supported.
• Exponential numbers are not supported.
• Nested arrays or arrays of objects are not supported.
• Maximum object depth is 2.
Method Supported URLs

GET Response /redfish/v1/SessionService
/redfish/v1/SessionService/Sessions
/redfish/v1/SessionService/Sessions/{session_ids}
/redfish/v1/AccountService
/redfish/v1/AccountService/Accounts
/redfish/v1/AccountService/Accounts/{username}
/redfish/v1/AccountService/Roles
/redfish/v1/AccountService/Roles/{rolename}
/redfish/v1/Managers

154
/redfish/v1/Managers/manager
/redfish/v1/Managers/1/NetworkService
/redfish/v1/RackPower/PowerDistribution
/redfish/v1/PowerDistribution/{pdu_id}<1>
/redfish/v1/PowerDistribution/{pdu_id}/PowerMeasurement/Loadsegment/{loadsegment_id}
/OutletMeasurement
/redfish/v1/PowerDistribution/{pdu_id}/PowerMeasurement/LoadsegmentMeasurement
/redfish/v1/EventService
POST Response /redfish/v1/AccountService/Accounts
/redfish/v1/SessionService/Sessions
DELETE /redfish/v1/AccountService/Accounts/{username}
Response
/redfish/v1/SessionService/Sessions/{session_id}
For the code on any of the above listed interfaces – please refer to Panduit TR128-SZ G5 RestfulAPI.pdf
For a copy of this document send a request to systemsupport@panduit.com

Panduit P36E09

Uploaded by

Copyright:

Available Formats

Panduit P36E09

Uploaded by

Document Information

Original Title

Copyright

Available Formats

Share this document

Share or Embed Document

Sharing Options

Did you find this document useful?

Is this content inappropriate?

Copyright:

Available Formats

Panduit P36E09

Uploaded by

Copyright:

Available Formats

Intelligent PDU User Manual v4.

INTELLIGENT PDU USER MANUAL

Configuring Users for SNMP v3 ................................................................................. 61

INTELLIGENT PDU USER MANUAL

Configuring Environmental Sensors ........................................................................ 105

INTELLIGENT PDU USER MANUAL

Appendix F: Panduit Network Controller Replace or Rotate 180° ............................... 129

INTELLIGENT PDU USER MANUAL

Figure 38: User Settings................................................................................................ 52

INTELLIGENT PDU USER MANUAL

Figure 76: Local Rack Access Web GUI ....................................................................... 94

INTELLIGENT PDU USER MANUAL

Section 1 – System Overview

Connecting the PDU via Ethernet Port

Figure 1: Ethernet Port for Network Connection

Connecting the PDU to a Computer Serial Port

To configure the network setting, perform the following steps:

Figure 2: Status LED & Serial In Port Identified

Section 2 – Web Graphical User Interface (GUI)

Connecting to the PDU

Changing Your Password

INTELLIGENT PDU USER MANUAL

Figure 3: Changing Your Password

1. Go to User Name and select Change Password.

Figure 4: After Login

2. The Change User Password window opens.

INTELLIGENT PDU USER MANUAL

Figure 5: Change User Password

Figure 6: Change Password

Logging in to the Web Interface

INTELLIGENT PDU USER MANUAL

INTELLIGENT PDU USER MANUAL

Introduction to the Web GUI

Figure 7: Login Page

Figure 8: Landing Page/Dashboard

INTELLIGENT PDU USER MANUAL

Number Icon Description

The home icon provides an

INTELLIGENT PDU USER MANUAL

Number Icon Description

click user guide and

Screen Resize Due to Multiple PDU Configuration

Figure 9 - Resized Dashboard Screen

INTELLIGENT PDU USER MANUAL

Introduction to the Dashboard

Figure 10: Power Summary Page

INTELLIGENT PDU USER MANUAL

Outlet Monitoring Page

Figure 11: Outlet Monitoring Page

Figure 12: Environmental Monitoring Page

Security Monitoring Page

Figure 13: Security Monitoring Page

INTELLIGENT PDU USER MANUAL

INTELLIGENT PDU USER MANUAL

System Management Information

To configure the system management information, select System Management under

Figure 14: System Management

INTELLIGENT PDU USER MANUAL

1. Select the pencil icon next to System Management.