1-GENERAL PHYSICS

UNITS OF MEASUREMENT
Measurement means comparing any physical quantity with a standard to determine
its Relationship to standard this standard is called unit all measurable quantity
expressed in
a) Some number or magnitude and
b) Some unit
For example if the distance is 200km, 200 is the number or magnitude and km
(kilometer) is the unit

Standard International Unit

M.K.S. system: meters – kilogram – second system used internationally. This system
is also called SI (system international) unit

kilometer ton
meter kilogram
centimeter gram

hour
minute
second

Powers of prefix
Prefixes are used to give multiples and submultiples. The prefix represents a power
of ten. The standard multiples and submultiples are mostly in steps of 103

1
 Symbol Prefix Value
n Nano 10-9
μ Micro 10-6
m Milli 10-3
C Centi 10-2
K Kilo 103
M Mega 106

Measuring length and Thickness

Length can be measured with a ruler to the nearest 1
mm. But when very small objects are used; we need to
take measurements to the nearest 0.01 mm the
micrometer screw gauge makes this possible.

Zero Error in measurement

Before taking a measurement, check that the reading is zero in measuring length
by ruler as shown in figure or measuring thickness when the jaws are closed. If
reading is not zero, then zero error must be allowed when the reading is taken.

More measurement technique

If you have to measure a small length, such as the thickness of a wire, it may be
better to measure several thicknesses and then calculate the average.

2
Take a stack of 500 sheets and measure its thickness with a
ruler then divide by 500 to find the thickness of one sheet.

Measuring Time
The common devices to measure the time or duration of an
event are clock and stopwatch
The precession of time duration of an event can be improved by
measuring the time for number of events and dividing time by total
number of events.

 For example to measure the time period of a pendulum the

time for ten swings should be recorded and dividing the total
time by ten to get the time for one swing

Period =

Scalar and Vector Quantities

 Scalar quantities: a quantity which has magnitude (size) only and is
described by its numerical value. ( distance, mass, speed, volume, time and
temperature )

 Vector quantities: a quantity which has both magnitude and direction, and
both should be mentioned to describe it ( displacement, weight, velocity and
acceleration)

3
Speed
To calculate speed

distance moved (m)

average speed (m/s) =
time taken (s)
s
v=
t

Questions

1. The runner completes 400 m is a time of 160 seconds. What is her average
speed?

Answer

distance moved 400

average speed = =
time taken 160

So the average speed = 2.5 m/s

2. An athlete completes a 4 km mountain race in at an average speed of 3 m/s.

How long does the race take?

Answer

distance moved 4000

time taken = =
average speed 3

The distance is given in 'km' and needs to be converted to meters

4 km = 4000 m.
So the time taken = 1333 seconds.

4
Acceleration
Is rate of change in velocity

When we speed up - increasing our velocity - we are accelerating , When we slow

down we are decelerating

 u = the initial, or starting velocity. (m/s)

 v = the final velocity (m/s)
 Δv = the change in velocity (m/s)
 t = the time taken (s)
 a = acceleration (m/s2)

change in velocity (m/s)

acceleration (m/s2)=
time taken (s)

v-u Δv
a= or a =
t t

Questions

3. The school bus accelerates from rest to a velocity of 16 m/s in a time of 20

seconds. Calculate the acceleration of the bus.

Answer

We know that the change in velocity (v-u, or Δv) is 16 m/s

Δv 16
a= =
t 20

so the acceleration = 0.8 m/s2

5
4. A cheetah is widely believed to be the fastest animal on Earth. It can
accelerate at 2.5 m/s2. If the cheetah starts at a velocity of 3 m/s, how long will
it take to reach a velocity of 13 m/s?

Answer

In this question, the change in velocity Δv = 13-3 = 10 m/s.

Δv 10
t= =
a 2.5

so the time taken = 4 s.

Motion graphs

There are two main types of graph used:

 Distance - Time graphs

 Velocity - Time graphs

1- Distance - time graphs

6
  Graph ( A ) gradient is speed and graph is straight line so it constant speed
opposite direction of ( D )
 Graph ( B )gradient is speed and graph is increasing ( stepper up ) so
increase in speed
 Graph ( C ) gradient is speed and graph is decreasing (stepper down ) so
decrease in speed
 Graph ( D ) gradient is speed and graph is straight line so constant speed

 Rest or stationary when graph is horizontal as shown on

figure

Questions

1. A man is taking his dog for a walk. When he opens the

front door, the dog runs off in a straight line at a steady speed. It then stops at
a lamp post for some time.

Sketch a distance-time graph for this motion. You do not need to estimate any
values for this question.

Answer

 The distance should be labeled on the y-axis.

 The time should be labeled on the x-axis.
 The first section of the line should be a straight line
sloping upwards showing "a steady speed".
 The next section should be a flat, horizontal line
showing the dog remaining in one spot at the lamp
post.

7
2. A student writes a program to make a small robot move
across the desk. This graph shows the motion of the robot

 a). Describe the motion in part 'X' on the graph.

 b). Describe the motion in part 'Y' on the graph.
 c). Describe the motion in part 'Z' on the graph.
 d) Calculate the speed of the robot when it is moving at
its fastest.

Answer

a) Line 'X' shows the robot moving away from the start at constant velocity.

b) Line 'Y' shows the robot stops / is stationary (100 cm from the start).

c) Line 'Z' shows the robot moving back towards the start at constant velocity.

d) The fastest speed is where the line is the steepest, (the highest gradient), which is
line X. For this section, reading from the graph, the robot covers 100 cm in 5
seconds. As we are using cm, the speed will be given in cm/s.

distance 100 cm
speed = =
time 5s

so the speed, or velocity, is = 20 cm /s.

8
2- Velocity - time graphs

 Graph ( A ) gradient is acceleration and graph is straight line so it constant

deceleration as velocity decrease
 Graph ( B )gradient is acceleration and graph is increasing ( stepper up ) so
increase in acceleration
 Graph ( C ) gradient is acceleration and graph is decreasing (stepper down )
so decrease in acceleration
 Graph ( D ) gradient is acceleration and graph is straight line so constant
acceleration

 when graph is horizontal as shown on figure zero

acceleration or constant velocity

9
Calculations distance using velocity-time graphs
A velocity-time graph is often used to show motion because you can use it to find
other information. The two that we will cover here are how to find
the acceleration and the distance travelled from the graph.

 The distance travelled = the area under the line.

 The acceleration = the gradient of the line.

Area under line

Area of triangle = 0.5 x base x height

Area of rectangle = base x height

Area of trapezium = 0.5 x h x (a + b)

Acceleration

This is the gradient of the line the steeper the line, the higher the acceleration. The
'steepness' of a line is the gradient

'rise' change in y-axis

gradient = or gradient =
'run' change in x-axis

10
Questions

The graph shown in figure gives data on the movement of a city tram moving
away from a station.
Which section or sections of the graph shows the
tram

a) Moving with constant velocity?

b) Decelerating?

c) Accelerating at the highest rate?

Answer

a) A constant velocity will be shown as a flat, horizontal line on a velocity-time

graph.
Therefore the sections showing this are Q and S.
b) Deceleration means slowing down, and this is shown by a sloping line with a
decreasing velocity.
The section showing this is section T.
c) A high acceleration is shown by a sloping line with a high gradient (like a very
steep hill).
This is shown by section R.
(Section P is also showing acceleration, but the tram is not accelerating as much as
in section R).

Using the graph shown in figure for the velocity of a

tram, calculate:

 a) The acceleration of the tram in section R.

 b) The distance travelled between 30 and 40
seconds.

11
  c) The distance travelled in the first 10 seconds.

Answer

a) The acceleration is given by:

change in velocity
acceleration =
time taken

change in y-axis
or by using acceleration = gradient =
change in x-axis

15 - 5 10
acceleration = =
10 10

So the acceleration of section R = 1 m/s2.

b) The distance travelled between 30 and 40 s is given by:

Distance = area under line = rectangle of height 15 (m/s) and length 10 (s).
Therefore the area = distance = 15 x 10 = 150 m.

c) The distance travelled in the first 10 s is given by:

Distance = area under line = area of triangle = ½ base x height,
So area = ½ x 10 x 5,
Area = distance = 25 m.

12
Mass

Mass is a measure of the quantity of matter in an object. In simple terms, it relates to

the number of atoms present, and how big those atoms are. The international unit
for mass is the kilogram (kg).

Weight

Weight is a measure of the pull of gravity on an object. As it is a pull, it is also a force

and is therefore measured in newton (N)

Weight = mass x gravitational field strength

W=mxg

[Newton] = [kilograms] x [N/kg]

 For many of these questions, the mass of an object will remain the
same (assuming it is the same object), but the weight can change as it depends
on the strength of gravity acting on it.
 Take the weight of 1.0kg to be 9.8N (acceleration of free fall = 9.8m/s2)

Questions

1. If we took the 5 kg bag of fruit on a space journey, how much would it weigh
in the following locations?

 a). The Moon. On the Moon, g = 1.6 N/kg

 b). Jupiter. On Jupiter, g = 23 N/kg
 c). Deep Space. Deep space, there is no gravity g = zero.

Answer

 a) W= m x g =5 x 1.6 = 8.0 N
 b) W= m x g =5 x 23 = 115 N

13
  c).In deep space, there is no gravity! g = zero.
Therefore W = 0 N (The bag is 'weightless').

2. On the Moon mission in 1972, the astronauts picked up a rock to bring back
to Earth. The weight of the rock was 32 N on the Moon. Calculate

 a). The mass of the rock.

 b). The weight of the rock when it was returned to Earth.

Answer

a). We know w = m x g. We also know that gmoon = 1.6 N/kg. Therefore

W
m=
g 32
m=
1.6

m = 20 kg.

b) If m = 20 kg, and on the Earth g = 9.8 N/kg,

then W = m x g
W = 20 x 9.8
Therefore W = 196 N

Density
It is defined as the mass per unit volume of a substance. The unit of density is kg/m3
or g/cm3.
It is denoted by Greek symbol ρ (rhoo) and is calculated from the formula

Density = ρ=

14
Measurement of physical quantities

1. The mass of an object is the amount of matter contained in this object. The mass
is usually measured in kilograms/grams using a balance (beam balance or top pan
balance).
2. The volume of an object is the amount of space occupied by this object. The
volume is usually measured in cubic meter (m3), cubic centimeter (cm3), or liter (l).

Determining the density of a regularly shaped object

1 .Use a mass balance to measure the mass m of the object
2 .Use a ruler to measure the dimensions (length and height and width) of the
object and then calculate its volume V = l x h x w
3.Then use the following formula to calculate density

Density =

Questions

A block of plastic is shown here.

 a) State the formula used to calculate density.

 b) Using information from the image, calculate the density
of the block.

Answer

a) m
ρ=
V

b) The volume of the block is length x height x width,

V = 10 x 8 x 8 = 640 cm3
768 g
ρ=
ρ = 1.20 g/cm3 640 cm3

15
Determining the density of a liquid
1- The mass m of the liquid can be measured using a mass balance. To find the mass
of the liquid we subtract the mass of the empty measuring cylinder from the mass of
the liquid and the measuring cylinder.
2- The volume V can be read directly from the measuring cylinder.
3- Then use the following formula to calculate density

Density =

Example

Use information in the diagram to calculate density of

liquid

Answer

Mass of liquid = 50 – 30 = 20

Volume = 10

So density of liquid Density = = 2 g/cm3

Determining the density of an irregularly shaped object

in the procedure below we use the displacement of water method to determine
the volume V.
1- Measure the mass m of the irregularly shaped object, in this case a stone, using a
mass balance
2- Partially fills a measuring cylinder with a known volume X of water.
3- Immerse the stone into
the water.

16
4- Measure the new volume Y
5- The volume of the stone is Y - X.
6- Use the following formula to calculate the density

Density =

Precautions
1. The measuring cylinder should be placed on a flat horizontal surface.

2. Look perpendicular to the scale of the cylinder (eye level) to avoid

parallax error.

3. The object must be completely submerged in water. If the object

floats in water (less dense than water) therefore a metal sinker is used
to submerge it.

4. Tie a string round the object and lower it gently to avoid splashing
of water (which will reduce the volume of water & cause an error).
5. Always measure from the bottom of meniscus when using
measuring cylinder

Questions
A customer orders are large block of aluminum for an art project.

 a) The block must have a length of 1.2 m, a width of 2.0 m, and a height
of 0.8 m. If the density of aluminum is 2700 kg/m3, calculate the mass of
this block.
 b) The customer suggests supplying the block in two halves of length
0.6 m, to make it easier to transport. What is the density of the
aluminum in one of these smaller blocks?

Answer

17
a) The volume of this large block will be:
V = 1.2 x 2 x 0.8 = 1.92 m3

m
The density formula is ρ=
V
So m = ρ x V,

m = 2700 x 1.92 = 5 184 kg

Floating and sinking

The density of pure water is exactly 1.0 g/cm3

If you put an object like a piece of wood on the surface of a pure water lake, then

 It will sink if the density is above 1.0 g/cm3 (the density of water)
 It will float if the density is below 1.0 g/cm3.

Forces

A force is basically a push or a pull on something. There are many different things
that cause forces, but they are all measured in newton’s (N)

Here are a few of the most common types of forces found in nature

 Magnetic - between magnetic materials. This can be a push (repulsion) or a

pull (attraction)
 Gravitational - between any mass. This is always a force of attraction.
 Friction - this is a force that acts against motion.
 Electrostatic - between positive and/or negative charges. This can be
attraction or repulsion, depending on the charge.
 Friction is a general term for any force produced when an object is in contact
with a solid, liquid or gas that pushes against the motion. If a liquid or gas is

18
 involved, we often call this force of friction the 'drag'. If it is an object like a
plane moving through the air, we often call this type of friction air
resistance.

When a force acts on something, many things can

happen
 Change the speed of a body.
 Change the direction of motion (if it is already moving).
 Change the shape of a body. (For example, squashing a rubber ball).

Drawing forces
Force is a vector so can be drawn with an arrow. The length of the arrow can be
used to show the size of the force, and obviously the direction of the arrow shows
the direction of the force.

 If two or more forces are acting in the same direction, we can add them
together to find the total.
 if they act in opposite directions, we need to subtract, as shown here by
two forces acting on a ball

Questions

1. A small van is travelling down a road. The forward force provided by the
engine is 2 kN . The air resistance acting on the van is 600 N, and the friction
between road and tiers is 300 N.

19
 a) What is the resultant force acting on the van?
b) Describe the motion of the van at this point.

Answer

 a) The forward force is 2 kN, which equals 2000 N. Air resistance AND
friction both act to prevent movement so act backwards, and total 900 N.
Therefore there is a resultant force of 1100 N (1.1kN) acting forwards.

b) As there is a resultant forward force, the van will accelerate

Two vectors point in completely different directions

Then the value of the resultant vector can be found graphically parallelogram

Draw a parallelogram to scale, in which two adjacent sides each represent a force.
Try to choose a simple scale, for example 1 cm = 1 N

 two lines representing two vectors ( draw with scale )

 arrow heads to show the direction in which each vector
acts
 complete the parallelogram
 measure the length of the diagonal
 use the same scale to convert this length to the resultant
force
 measure the angle (direction) of the resultant to the
horizontal

Force and acceleration

If there are unbalanced forces acting on the object, the object will accelerate. The
acceleration depends on the size of the unbalanced/net force and the mass of the
object

20
  A force can make an object accelerate. The bigger the force acting on an
object, the bigger the acceleration that it gives to the object 𝑎 ∝ F
(proportional) so, doubling the force acting on an object doubles its
acceleration.
 The mass of an object affects how easily it can be accelerated or decelerated.
The bigger the mass, the smaller the acceleration given by a particular force
𝑎∝ (inversely) so, doubling the mass of the body will halve the

acceleration

Force= mass x acceleration

F=mxa

[newtons] = [kilograms] x [m/s2]

Questions

A mountain bike rider and bike together have a total mass of 80 kg. If the bike
is to accelerate at 1.8 m/s, what force needs to be applied?

Answer
F= m x a
Therefore F = 80 x 1.8 = 144 N

A firework rocket of mass 200 g is set alight, and the force produced at the
start is 5 N.

 a). Calculate the initial acceleration of the rocket.

 b). the rocket burns and releases fuel, making it lose mass. At what
mass will the acceleration be 40 m/s2, assuming the force produced is
still 5 N?

Answer

a). We know F = m x a and also that 200 g = 0.2 kg (the mass MUST be in kg, not g).

21
Rearranging the formula gives:
F
5 a=
a= m
0.2

a = 25 m/s2

b) If a = 40 m/s2 and F = 5 N,
then F = m x a gives:

5 F
m= m=
40 a

Therefore m = 0.125 kg (or 125 g)

The Effect of a Force acting perpendicular to the direction

of motion
Here, the force is neither driving nor resisting, it acts as a centripetal force which is
the inward force needed to make an object move in a circle
As a result Object moves along circular path (or part of a
circular path).
 For this car moving round a circular road, what
provides the centripetal force? The sideway friction
exerted by the road on the tires.
 Object can have a steady speed but a changing
velocity as object moving in a circular path
(acceleration change )

22
 Larger centripetal force
1) if the mass of the object is increased
2) if the speed of the object is increased
3) If the radius of the circle is reduced.

Air Resistance and Terminal Velocity of falling object

There are two main forces which affect a falling object at different stages of its fall:

 The weight of the object - this is a force acting downwards, caused by the
Earth's gravitational field acting on the object’s mass.

 Air resistance - this is a frictional force acting in the opposite direction to

the movement of the object. (Note that in space and other vacuums there is
no air resistance.)

Stages of falling

When an object is dropped, there are three stages before it hits the ground:

1. At the start, the object accelerates downwards because of its weight. There is
very little air resistance. There is a resultant force acting downwards. The
acceleration is constant when the object is close to Earth.

2. As it gains speed, the object's weight stays the same but the air resistance on
it increases. There is a resultant force acting downwards.

3. Eventually, the object's weight is balanced by the air resistance. There is no

resultant force and the object reaches a steady speed – this is known as
the terminal velocity

 in skydiver as he open parachute the air resistance increase because large

surface area of parachute , air resistance is greater than weight so he start
to decelerate

23
24
Questions

1. The diagrams below figure show forces acting on a skydiver who has
jumped out of a plane. There are 3 diagrams, showing different stages of the
descent

 a). Describe the acceleration in diagram A.

 b). Describe the acceleration in diagram B.
 c). Describe the acceleration in diagram C.
 d). State the causes of the forces acting downwards
and upwards on the skydiver.
 e). Complete the velocity time graph shown below
to show each of these stages of the skydiver's fall
from figure. You do not need to include numbers
on the graph.
The initial downwards velocity of the skydiver is zero, as shown by the
line section given at the start of the graph.

Answer

 a). The downwards force in diagram A is larger (by 300 N) and so the
skydiver accelerates downwards.
 b). The forces are balanced, so the skydiver stays at a constant velocity.
Remember the question asks you to describe acceleration - the acceleration
is zero.
 c). There is now a resultant force upwards. Be careful - this does NOT make
the skydiver go back up to the plane. They are falling
downwards, so the unbalanced force just slows them down.
The skydiver decelerates (or has negative acceleration).
 d) The downwards force is gravity, and the upwards force
is air resistance.
 e) See the example here

25
Falling object in vacuum (space)
The graph will be straight line due to absence of air resistance
as shown in figure

Forces and Deformation

If an object is under the effect of a force, that changes its shape, then this object has
experienced deformation. Deformations of objects are either:
1. Elastic deformation
Is when an object (under the effect of a certain force) experiences a change in shape,
then returns to its original shape when the deforming force is removed,
stretching a rubber band
2. Plastic deformation
Is when an object (under the effect of a certain force) experiences a change in shape,
and does not return to its original shape when the deforming force is removed,
squeezing a piece of plastic
Most materials are elastic for a certain range for forces “the Elastic limit”, beyond
which they have plastic behavior.

Hooks experiment
In the opposite figure, a clamp and stands are used to
show a stretched spring supporting some weights at rest.
When the spring extends (increases in length), therefore
the difference between the non-stretched length of the
spring and its stretched length (when loaded) is called
“Extension”.
𝐸𝑥𝑡𝑒𝑛𝑠𝑖𝑜𝑛=𝑆𝑡𝑟𝑒𝑡𝑐𝑕𝑒𝑑 𝑙𝑒𝑛𝑔𝑡𝑕−𝑛𝑜𝑛 𝑠𝑡𝑟𝑒𝑡𝑐𝑕𝑒𝑑 𝑙𝑒𝑛𝑔𝑡𝑕
(original length)

26
  Attach a spring to a clamp or similar support, and measure the upstretched
length with a ruler.
 Add a load to the spring. Remember that a mass of 0.1 kg will have a weight
of 1 N.
 Measure the new, stretched length.
 Repeat this with additional weights, recording the new length.
 Once finished, work out how much the spring has stretched compared to the
original length - this is known as the extension, shown in the diagram as 'x'.

Plot the extension x (cm) against the load (N) applied to see how the spring has
behaved under a force

27
The limit of proportionality
 Is the point beyond which the spring extension will not be proportional to
the load Up to this limit the extension increases by a set amount for every
newton of force applied Above this limit the increase in extension per
newton will be greater.
 The limit of proportionality is an important point.
If the spring is stretched beyond this point, it will no longer
extend proportionally to the load (weight) applied.

Hook’s law
Force (F) is Directly Proportional with extension (X) Until Elastic Limit
F=K xX
Where k is spring constant

Springs connected in series and in parallel

Springs can be connected in different ways; end to end (in series) or side by side (in
parallel).
 When two springs are connected in series, they produce
twice the extension because the two extensions add up.
 When two springs are connected in parallel, they
produce half the extension because each spring is
affected by half the force.

Questions

A wire of length 50 cm stretches to 70 cm under a load of 40 N. What will be

the length of the wire when 60 N is applied?

28
Answer

If the wire extends from 50 cm to 70 cm, the extension for 40 N loads is 20 cm. (0.5
cm per 1 N load).
Therefore for 60 N, the extension will be 30 cm. However this is NOT the final
answer! The question asks for the length, not the extension.
The original length was 50 cm, so the extended length will be 50 + 30 = 80 cm

How is Hooke's Law identified on a graph of the load on a spring against the
spring's extension?

Answer

Hooke's Law behavior is shown by a straight line

section on a load-extension graph.

What do we mean by elastic behavior?

Answer

Elastic behavior means that a material will return to its original shape after being
deformed.

29
Moment (turning effect)
When a force acts on an object which has a pivot a point around which an object
can turn or rotate, it creates a turning effect or moment. When forces are used to
open doors, steer and pedal bicycles or turn a tap; they are causing turning effect
The moment of a force is defined like this

Moment = force x perpendicular distance (from the pivot)

Moment = F x d

 The moment of a force is a vector quantity that can only have one of two
directions; either clockwise or anticlockwise

Combining moments
Questions

In the diagram, there are two forces acting, F1 and F2:

 a) Which of these two forces is trying to rotate the

spanner in a clockwise direction?
 b) Calculate the clockwise moment on the spanner.
 c) Calculate the anticlockwise moment on the
spanner.
 d) Which way will the spanner turn, if at all?
 e) Calculate the total moment acting on the spanner.

Answer

a) Force F2 is pushing upwards on the left hand side, so is trying to turn the spanner
in a clockwise direction.

b) The moment of F2 = force x perpendicular distance to the pivot

So moment = 40 x 0.4 = 16 Nm clockwise

30
c) The moment of F1 = force x perpendicular distance to the pivot
So moment = 30 x 0.6 = 18 Nm anti-clockwise

d) The anti-clockwise moment is larger (18 Nm compared to 16 Nm) so the spanner

will rotate anti-clockwise.

e) The anti-clockwise moment is larger by 2 Nm, so therefore the total resultant

moment is 2 Nm anti-clockwise.

The principle of moments

A system will not rotate (is in equilibrium) if the sum clockwise moments equal the
sum anti-clockwise moments

F1 d1 = F2 d2
or m1 d1 = m2 d2

Conditions for equilibrium

1. The resultant force must be zero. The sum of the forces in one direction must
be equal to the sum of the forces in the opposite direction.
2. There should be no resultant turning effect the sum of the clockwise moments
equals the sum of the anticlockwise moments about any point (so the object is
balanced).

31
Questions

1. Two children (with unusual body shapes) are on a

'seesaw' in a playground. The seesaw is balanced. What
is the weight, W, of the child on the right hand side?

Answer

If the seesaw is balanced, then the anti-clockwise moment = clockwise moment

The child on the left (L) is turning the seesaw anti-clockwise, so we can write:
FL x d L = FR x d R
The weight W of the child on the right is called FR in this formula, so:
300 x 1.5 = W x 1.2
450 = W x 1.2

450
W=
1.2

W = 375 N

2. Two boxes are balanced on a long beam as shown. What is the missing
distance labeled d - the distance
of the center of the right hand
box from the pivot?

Answer

If the system is balanced, then the anti-clockwise moment = clockwise moment, So

FL x d L = FR x d R ,
6 x 30 = 9 x d 180
180 = 9 x d , so d =20 cm (or d = 0.2 m) d=
9

32
Center of Gravity (center of mass)
It is a point where the whole weight of a body may be considered to act.

Center of gravity of a regularly

shaped object
It is easy to find the center of gravity/mass for
regularly shaped objects as it usually lies at the point
you would immediately identify as the middle.

Center of gravity of a irregularly shaped

( lamina )
1. Pin the object from one point so that it rotate
freely
2. Draw vertical line once the object reaches
equilibrium
3. Repeat step 1 & 2
4. The point of intersection is the center of mass

Explanation
 When the lamina is released, its weight causes a turning effect which makes it
swing.
 When the lamina comes to rest, the weight has no turning effect since the line of
action of weight passes through the pivot in each case the center of gravity of the
lamina lies somewhere along the plumb line, so it has to be at the point where
the two lines cross.

33
Center of Gravity and Stability
The stability of a body is increased by
1) Lowering its center or mass
2) Increasing the area of its base (wide)

Momentum
Imagine you work in a sports shop. Some of the equipment is stored on very high
storage platforms. Your job is to catch the equipment as it is
thrown down to you.

Which would you rather catch - the netball or the large punch
bag from the top platform?

This idea of 'how hard it is to stop' is called the momentum of

an object. A heavy, fast object will have a lot of momentum.
A fast car has more momentum -is harder to stop - than a
bicycle because it has more mass and a higher velocity.

The formula for momentum depends on the mass and the velocity of the object

Momentum = mass x velocity

p=mxv

[kg m/s] = [kg] x [m/s]

The units of momentum are simply the units of mass (kg) multiplied by the units for
velocity (m/s), and are therefore kg m/s

For example, a 2 kg rock rolling down a hill at 3 m/s will have a momentum of 6 kg
m/s.

34
Impulse
The impulse of a force is the change in momentum that it causes. Using the concept
of impulse, the second law can be written as
𝑖𝑚𝑝𝑢𝑙𝑠𝑒 = 𝑓𝑜𝑟𝑐𝑒 ×𝑡𝑖𝑚𝑒 = 𝑐𝑕𝑎𝑛𝑔𝑒 𝑖𝑛 𝑚𝑜𝑚𝑒𝑛𝑡𝑢𝑚

change in momentum (kg m/s)

force (N) =
time (s)

Impulse, like momentum, is measured in Ns or Kg m/s.

Questions

1. 100 g toy car accelerates from rest to 2 m/s in 5 seconds.

What force is needed to make the car accelerate?

Answer

Δp (mv - mu)
F= =
t t

 m = 100 g = 0.1 kg (remember to convert units to kg!)

 u = 0 m/s
 v = 2 m/s
 t=5s

(0.1 x 2) - (0.1 x 0)
F=
5

(0.2) - (0) 0.2

F= =
5 5

F = 0.04 N

35
2. On a roller-coaster ride, passengers are held safely in their seats by seat
belts. The belt provides a force that will push backwards on the passengers
and slow them down in an emergency.

The maximum force that the seat belts can apply is 2 kN.
If a 100 kg passenger slows down from 15 m/s to rest, calculate:

a) The change in momentum of the passenger.

b) The shortest time in which the passenger can be stopped safely.

Answer

a) The initial velocity here is 'u' and equals 15 m/s. The final velocity v = 0, so:
Change in momentum Δp = mv - mu,
so Δp = (100 x 0) - (100 x15),
Δp = -1500 kg m/s. (or just 1500 kg m/s - the negative sign tells us that the
momentum is reducing instead of increasing. however the change is momentum is
still 1500 kg m/s, so both answers will be marked as correct).

b) We know that

Δp (mv - mu)
F= or F =
t t

1500
so the maximum force 2000 =
t

1500
t=
2000

t = 0.75 seconds at the shortest.

If the time is shorter than this, the force will exceed 2 kN and the seatbelt may
break.

36
Momentum and safety
 The force on our bodies depends on the change in momentum and also
the time taken to do this. If the time is longer, the force needed will be
smaller.
 seat belt or air bag or crumble zone is safety features on car as it increase
impact time , so reduce force on passenger for less injures since change in
momentum is conserved

Conservation of momentum
The total momentum before any collision is equal to the total momentum after the
collision, as long as no external forces act

Momentum before collision = momentum after collision

 elastic collision ( bounce off )

m1u1 + m2u2 = m1v1 + m2v2

37
 Questions
Use information in the diagram and calculate velocity of van after
collision?

Answers
Momentum before collision = momentum after collision
m1u1 + m2u2 = m1v1 + m2v2
1200 x 10 + 3200 x zero = 1200 x 2 + 3200 x m2
12000 = 2400 + 3200 x V2
12000 – 2400 = 3200 x V2
9600 = 3200 x V2
V2 = 3 m/s

 inelastic collision ( join together )

m1u1 + m2u2 = ( m1 + m2 )v

Questions
Use information in the diagram and calculate velocity of van and car
after collision?
Answers
Momentum before collision = momentum after collision
m1u1 + m2u2 = ( m1 + m2 )v

38
 1500 x 8 + 900 x zero = (1500 + 900) V
12000 = 2400 V
V = 5 m/s

Energy

Physicists say that "work is done when energy is transferred." Work and energy
are both measured in joules (J).

There are a few different classes of energy

1) Potential Energy
Is the type of energy stored in a body and available to do work

a) Gravitational Potential Energy (GPE)

Is the energy of an object due to its position or height (about the Earth’s surface).
The change in GPE of an object depends on the change in its height.
G P E = Mass of Object x Gravity x Height

Questions

A student of mass 60 kg climbs up a long flight of stairs of height 30 m.

Calculate the gain in gravitational energy.

Answer

G.P.E. = m g h
G.P.E. = 60 x 9.8 x 30
so the gain in G.P.E. = 17640 J

39
A farmer has a small hydroelectric scheme that stores water in a large tank
high on a hill when needed, the water flows downhill and through a generator,
transferring the stored gravitational energy to electrical energy. The tank is
50 m above the nearby river.
What mass of water needs to be stored at this height so that the tank stores 2
MJ of gravitational energy?

Answer

G.P.E. must be 2 MJ (2 million joules)

G.P.E. = m g h
2 000 000 = m x 9.8 x 50
2 000 000 = m x 490
rearranging the equation gives

2 000 000
m=
490

So m = 4081 kg

b) Chemical Potential energy

Stored form of energy released by chemical reactions.
 Chemical energy in fuels released by burning them
 Chemical energy in batteries, when in use, it is transferred to electrical energy.
 Chemical energy of food is released by chemical reactions in our body
(respiration).

40
c) Elastic Potential Energy (Strain Energy)
This is the energy stored in a body when it stretch or bend this type of stored
energy is used in rubber band , or spring

d) Nuclear Potential Energy

Energy stored in the nucleus of an atom.
This nuclear energy can be released from the
nuclei of certain elements (radioactive
elements) by either
 Nuclear Fission splitting of a heavy
nucleus into lighter nuclei
 Nuclear Fusion The join of light nuclei to form heavier ones, energy is released
by nuclear fusion in the sun.

2) Kinetic Energy
Is the energy of an object due to its motion the faster the object moves, the more
KE it has.

𝐾𝐸= 𝑚 𝑣2
Where, KE = Kinetic Energy, in Joules
m = mass of object, in kg
v = speed of object, in m/s

Questions

2 kg cat is running across a room at 4 m/s. What is the kinetic energy of the
cat?

41
Answer

K.E. = ½ m v2
K.E. = ½ x 2 x 42
So K.E. = ½ x 2 x 16
so the cat has a K.E. = 16 J

A dog is chasing the cat from question 1. It has mass of 14 kg and a kinetic
energy of 63 J

Answer

K.E. = ½ m v2
Substituting in the values from the question gives
63 = ½ x 14 x v2
63 = 7 x v2
rearranging the equation

63
v2 =
7

v2 = 9 square route of answers giving v = 3 m/s

Conservation of Energy
The Law of conservation of Energy states that
" 𝑬𝒏𝒆𝒓𝒈𝒚 𝒊𝒔 𝒏𝒐𝒕 𝒄𝒓𝒆𝒂𝒕𝒆𝒅 𝒐𝒓 𝒅𝒆𝒔𝒕𝒓𝒐𝒚𝒆𝒅 𝒊𝒏 𝒂𝒏𝒚 𝒑𝒓𝒐𝒄𝒆𝒔𝒔,𝒊𝒕 𝒊𝒔 𝒋𝒖𝒔𝒕 𝒄𝒐𝒏𝒗𝒆𝒓𝒕𝒆𝒅
𝒇𝒓𝒐𝒎 𝒐𝒏𝒆 𝒕𝒚𝒑𝒆 𝒕𝒐 𝒂𝒏𝒐𝒕𝒉𝒆𝒓 ”

42
Some examples of energy conversion
 A light bulb converts electrical energy to light energy;
 A moving car converts chemical energy from petrol to kinetic and heat energy;
 A drill machine converts electrical energy to kinetic energy.

 A mountain climber changes chemical energy from his muscles to potential

energy.

Questions

A ball rolls down a hill. State the energy store at the top and at the bottom of
the hill.

Answer

At the top of the hill the ball will have stored gravitational energy. At the bottom,
the ball will have accelerated and have kinetic energy.

A catapult is used to fire a small stone, using a strong elastic band.

i) State the energy store in the catapult just before, and after firing.

Answer

i) Before firing, there is a store of elastic energy. Afterwards, the stone has a store
of kinetic energy.

43
Kinetic energy to gravitational potential energy and vice
versa
At the top of the board, the diver has gravitational potential energy. When the diver
jumps, this G.P.E. will convert to K.E. However,

G.P.E. of the diver = mgh.

Substituting in the values gives
G.P.E. = 50 x 9.8 x 8
So the G.P.E. = 3920 J

This will convert into kinetic energy.

K.E. = ½ m v2
Substituting in the values from the question gives
3920 = ½ x 50 x v2
3920 = 25 x v2
rearranging the equation gives

3920
v2 =
25

v2 = 156.8
so v = √156.8 giving v = 12.5 m/s

Questions

A 100 g tennis ball is thrown upwards at 20 m/s. If we ignore air resistance,

how high will it go?

Answer

The mass of the ball is 0.1 kg (don't forget to convert 100g to kg)
If the velocity is 20 m/s we can calculate the K.E. of the ball

44
K.E. = ½ m v2, therefore
K.E. = ½ x 0.1 x (20)2
K.E. = 20 J

This is converted to G.P.E., so G.P.E. = 20 J

G.P.E. = m g h
20 = 0.1 x 9.8 x h
so h = 20.4 m

Efficiency
The efficiency of any process that does work by transferring energy

useful energy output

efficiency = x 100%
energy input

Questions

1. A small toy car uses a spring inside to drive the car. The spring can be
wound up using a key, and then the car
released.

This sankey diagram shows the energy

transfers that take place. Some labels are
missing from the diagram.

a) What form of energy is stored in the

spring at the start?

b) What form of energy store does the car have once it is released?

c) How much energy is dissipated as heat into the surroundings?

d) State the formula for efficiency.

e) Calculate the efficiency of the toy car.

45
Answer

a) The spring stores elastic energy.

b) Once the car is released, the energy stored into the spring as elastic energy is
transferred to kinetic energy.

c) The energy lost as wasted thermal energy is dissipated into the surrounds. The
missing value is 24 J - 18 J = 6 j

d) useful energy output

efficiency = x 100%
energy input

18
e)
efficiency = x 100%
24
Efficiency = 75 %

Work
Is the product of the force (F) and the distance (d) in the direction of the force
Work done = force × distance moved in the direction of force
Work = F × d
 The unit of work (and energy) is the joule

Example
 Work is done when you push a car to start it moving: you force
transfers energy to the car; the car’s KE increases (you lose energy
while the car gains)
 Work is not done when you push a car but it doesn’t move; no
energy is transferred because your force does not move the car. The
car’s KE does not change.

46
Questions

A dolphin swims for 1 km in water, producing a forward force of 800 N to

overcome the resistance from the water. Calculate the work done by the
dolphin.

Answer

We know W = F x d, and 1 km is equal to 1000 m

W = 800 N x 1000 m
W= 800 000 J

A small toy boat contains a battery storing 2 kJ of energy. When moving at top
speed, the resistance from the water is 12 N Assuming the boat motor is 100 %
efficient, how far could the boat travel before the batteries run out?

Answer

We know that W = F x d, and the work done will be 2 000 J assuming all the battery
energy is transferred. So:
2 000 = 12 x d

2000
d=
12 d = 167 m

An 8 kg drone is moving upwards at a constant speed to take pictures of a new

building from above. It travels 600 m upwards.

a) What is the weight of the drone?

b) What work has been done getting to this height?

47
Answer

a) The weight of the drone is given by = m g

so weight = 8 x 9.8
Weight = 78.4 N

b) Work done = F d
so Work = 78.4 x 600
Work done = 47040

Power
Is the rate at which energy is transformed from one form to another or the work
done per unit time

Power =
 Unit of power 1 Watt = 1 joule/second

Power can be defined in two ways

 Power is the rate of transfer of energy

 Power is the rate of doing work

Questions

A phone battery needs 28 kJ of electrical energy to be transferred to fully

charge the phone. If the charger supplies 4 W of electrical power, how long
will it take to charge the phone?

Answer

W 28 000
p= 4=
t t

48
rearranging this equation gives

28 000
t=
4

t = 7 000 seconds

Amy is timed running up some stairs. She weighs 550 N, and takes 12.5
seconds to complete the climb. The stairs have a vertical height of 9 m.

Calculate

a) The work done by Amy climbing the stairs.

b) Amy's average power output during this climb.

Answer

a) Amy's weight is the downward force of gravity (F) on her. The work done is given
by
W = F d So W = 550 x 9 = 4 950 J

b) Her power output is given by

W 4 950
p= and therefore:- P =
t 12.5

Her power output is P = 396 W

49
ENERGY SOURCES
Renewable energy source
Renewable energy source is the one that is generated from natural resources such
as sunlight,
Wind, waves, tides and geothermal and hydroelectric heat which means it can be
received from nature forever

Non-renewable energy source:

Non-renewable energy sources are those energy sources that are used up and
cannot be replaced.
One day they are going to be finished. These are fossil fuels like coal, oil and
natural gas and Nuclear fuel like uranium,

 The Sun is the source of energy for all our energy resources except geothermal,
nuclear and tidal.
1) Solar energy
Solar heating systems consist of water-filled black panels. Heat from the Sun
warms the panels, and the hot water can be used directly, for central heating
systems or for hot water at home.

Solar panels work in a different way. They convert

sunlight directly into electricity using silicon crystals.
These panels contain smaller photovoltaic cells which
generate a current.

2) Wind Power
Wind energy turns the turbine blades in a wind turbine. The turbines rotate the
generator. The kinetic energy of the wind is converted into electrical energy by the
generator.

50
3) Water
 hydroelectric power station
Energy stored as G.P.E. transfers to kinetic energy as it flows down through
pipes to turbines and a generator, which convert this to electrical energy.

 A tidal power station uses the rising and falling of water in the sea to generate
electricity. The tides are produced by the gravitational pull of the Moon and Sun
on the seas

 Waves

Generators are driven by the transverse (up and down)

motion of the wave.
The kinetic energy of the wave motion causes water to rise

51
and fall in the air chamber. The air above the water causes the turbine to turn and
electricity is produced by the generator.

4) Geothermal
Geothermal power stations use heat from underground where
hot rocks lie near to the surface. Water is pumped in pipes down
to hot rocks and returns as steam to turbine and a generator
produce electricity.

5) Fossil fuels
Fossil fuel power stations can produce a large power output, 24 hours a day. For this
reason, the majority of the World's electrical energy is still produced in this way.
Fuel (coal, oil, gas) energy stored as chemical energy by burning fuel it converted as
thermal energy which supply in water in boiler water turn into steam kinetic energy
of steam turn turbine and generator produce electricity

52
6) Nuclear power

Nuclear power stations have a huge power output and are also reliable, working 24
hours a day. Nuclear energy stored in nucleus (uranium atom) by fission it release
huge energy thermal energy released which supply in water in boiler water turn
into steam kinetic energy of steam turn turbine and generator produce electricity

Advantages of non-renewable sources Disadvantages of non-renewable

sources

These fuels are far more energy dense Fossil fuels are becoming increasingly
than renewable sources and thus, in expensive to mine (coal) and drill for
many countries, they allow production of (oil), as reserves are running out (being
larger amounts of energy in depleted).
comparison to renewable sources. They They cause global warming due to high
are also relatively easy to transport and carbon dioxide (CO.) emissions when
can be stored ready for use. they are burnt. Some also produce sulfur
dioxide (SO,), which causes acid rain.
Nuclear power stations are expensive to
build and any radiation
leak or explosion may have a
devastating effect on the immediate
population and environment

53
Advantages of renewable sources Disadvantages of renewable sources

They are all regarded as clean Generally all renewable energy sources
(producing little or no pollution) and have high installation costs
will not run out. The fuel itself is cheap
or free.

Solar energy
- When the sun doesn't shine (at night) no electricity is produced.
- Dirty solar panels are inefficient.
- To install panels is an expensive process.
- The panels take up large areas.

Wind energy
- When the wind doesn't blow no electricity is produced.
- Wind farms can destroy the natural beauty of a landscape and are noisy.
- Offshore wind farms are expensive to build and need to be avoided by shipping.

Wave energy
- Waves vary in size and therefore will produce varying quantities (amounts) of
energy. When the sea is calm, no electricity is produced
- Installation is expensive and challenging.
- Boats would have to be careful and be aware of the location of the turbines to
prevent accidents.

Tidal energy
- Many countries do not have suitable locations.
- Might affect local marine life and destroy habitats.

54
Geothermal energy
- There are few locations that are suitable.
- It is often necessary to drill very deep and this makes the energy very expensive to
obtain.

Hydroelectric energy
- The local environment may be destroyed because water needs to be stored behind
a dam, the land behind it flooding.
- Dams are expensive to build.

Pressure

1) Pressure under Solids

Pressure indicates how the force is shared out over the area it acts on, pressure is
defined as the normal force acting per unit area.

Pressure =

 Where, force is measured in Newton (N), area is measured in square meters (m2)
and the unit for pressure is Pascal (Pa).
 1 Pa = 1 N/m2

55
Questions

1. A syringe is used to squeeze a liquid down a tube. A force of 5N is applied to

an area of 0.8 cm2. Calculate the pressure on the liquid

answer

F 5
P= P=
A 0.8

Therefore P = 6.25 N/cm2

2. A classroom stool has a weight of 160 N. Each of the 4 stool legs produces a
pressure of 8.0 N/cm2 on the floor.
Calculate the area of each stool leg that is in contact with the floor.

Answer

Each stool takes ¼ of the weight. This means the force on each leg is ¼ of 160 N, or
40 N each.
We know that:

F F 40
P= A= and therefore A =
A P 8

A = 5.0 cm2 (The pressure was given in N/cm2 so the answer must be in cm2, not
m2).

56
2) Pressure in fluids (liquids & gases)
A liquid held in a container exerts pressure on the inner walls of the container as
well as on any object that is inside the liquid. Following are the properties applied to
any object in a liquid.
1. Pressure of liquid on an object acts equally in all direction,
2. Pressure of liquid increase with the increase of depth,
3. Pressure depends upon the density of the liquid,
4. Pressure does not depend upon the shape of the container.
The pressure due to liquid of density ρ and height h can be expressed by
Pressure = Density x Gravity x Height
P=ρxgxh
Where
 P is the pressure difference between two points in a liquid or a gas.
 h is the depth beneath the surface of the liquid (measured in meters). The
greater the depth, the greater the pressure.
 ρ is the density of the liquid (kg/m3). The greater the density, the greater the
pressure at any depth.
 g is the gravitational field strength (N/kg)

The atmosphere
The Earth's atmosphere is a thick layer of a mixture of gases. This produces a
pressure just like a deep pool of water

When diving in a swimming pool, we are under atmospheric pressure at

the surface and under an additional pressure due to the water as we
swim downwards.

Total pressure = atmosphere pressure + water pressure

57
Questions

A whale is diving for food in sea water of density 1050 kg/m3.

 a) Calculate the water pressure on the whale at a depth of 500 m.

 b) The whale's eye has an area of 0.0015 m2. Calculate the inward force
acting on the eye at this pressure.

Answer

a) We know that P = ρ x g x h.
The value of 'g' on earth can be taken as 10 N/kg.
P = 1050 x 10 x 500
P = 5 250 000 Pa

b) F = P x A,
F = 5 250 000 x 0.0015
F = 7 875 N

The maximum pressure increase for safe recreational diving in water is given
as 400 kPa. In a fresh water lake of density 1000 kg/m3, how deep can a diver
go so that this limit is not exceeded?

Answer

P = ρ x g x h.
So 400 000 = 1000 x 10 x h
400 000 = 10 000 x h

400 000
h=
10 000

h= 40 m

58
 2-Thermal PHYSICS
Thermal Physics
The branch of physics that study the temperature, heat energy and their relation to
the matter
Molecular Model
Matter is made up of atoms and molecules, which may only be seen by electronic
microscope
States of Matter
 All matter is made up of tiny particles (molecules) that are moving. The idea that
molecules have a certain kind of motion is called the Kinetic Theory. The way
that the particles are arranged and the way that they move determine the
properties of a material, such as its state at room temperature or it density.
Therefore, the kinetic theory can explain the existence of solid, liquid and gas
states.

 All substances can exist in any of the three states solid, liquid or gas. The
increase in particle separation during a change of state from solid to liquid is
small, whereas particle separation during change of state from liquid to gas is
large. This particle separation is responsible for the main physical properties
that we observe for any of the three states

Solid
 are tightly packed (dense)
 Are held in a fixed pattern or crystal
 Structure by strong forces between them (have a fixed shape).
 Have fixed volume and are incompressible.
 Vibrate around their fixed positions within the close-packed
regular structure.

59
  As we heat a solid, the particles vibrate more quickly. The increase in the
kinetic energy of the particles is noticed as an increase in the temperature of
the substance.

Liquid
 Are tightly packed (but have slightly smaller densities than
solids).
 Are not held in fixed positions but are still bound together by
strong forces between them. Thus, they have a fixed volume but
not a fixed shape.
 Take up the shape of their container (occupy the lowest part) and are almost
incompressible.
 Move at random with close packed irregular structure.
 As we heat a liquid, the movement of the particles becomes more
energetic.

Gas
 Are very spread out (have much smaller densities than solids and liquids)
 Have no fixed positions and the forces between them are very weak. Thus,
 Have neither a fixed shape nor a fixed volume.
 Can fill up all the space available to them and are compressible.
 Move with a rapid, random motion.
 Bump into anything in the gas or into the walls of the container, and
forces caused by these collisions are responsible for the pressure
the gas exerts.

60
 Summary of the properties of solids, liquids and gases
Property Solids Liquids Gases
Attractive forces Very strong strong attractive Negligible attractive
between molecules attractive forces forces forces
Spacing between molecules are molecules are Molecules are far
molecules closely packed loosely packed apart
Motion of Vibrate about a Move around while Move with rapid,
molecules fixed position sliding past each random motion
other
shape Fixed Not fixed, take up Not fixed
the shape of the
container
Can be easily no no yes
compressed

Heating and change of state

When substances gain or lose energy, one of two things happens to the substance:
its temperature changes OR its state changes. Putting heat energy into a solid does
not necessarily increase its temperature. It may make the solid change into a liquid
and similarly heat may make the liquid change into a gas.

 Melting is the change of state from a solid to a liquid. The melting point of a
substance is the temperature at which the substance changes from a solid to a
liquid. Most substances have a unique melting point that can be used to identify
them.
 Freezing is the reverse process of melting. It is the change of state from a liquid
to a solid (sometimes called solidification). During freezing, some bonds are
formed between the molecules and energy is released to do this.
 Condensation is the change of state from gas to liquid, during which energy is
also released and bonds are formed.

61
Heating curve
If we take an ice cube as an example, and we start heating it, the following curve is
obtained (by plotting temperature against time).

 The graph is horizontal at two places. These are where energy is being used to
break the bonds (against attractive force) between the particles to change the
state, rather than increase the speed of the particles (and so to increase the
temperature).
 The longer the horizontal line, the more energy has been used to cause the
change of state (boiling)

62
 Cooling curve
 during condensing and freezing, internal energy decreases as the motion of
particles decreases and new bonds are formed Horizontal line Freezing
(Solidifying )
 The more stepper Graph the more rate of cooling

Questions

1. Liquid oxygen can be stored in containers for transporting.

 a) Describe the arrangement of oxygen molecules in a liquid.

 b) Describe two changes to this arrangement as the oxygen is released
from the container as a gas.

Answer

a) The molecules are close together, moving past each other, taking the shape of the
(bottom of the) container, moving randomly, have weak forces between them
holding them near to each other

63
b) The molecules move far apart, move faster, have no forces keeping them together,
fill the container they go into or spread through the atmosphere.

2. Some ice cubes are left outside on a sunny day.

 a) Describe the changes that take place to the molecular arrangement

in the ice as it melts.
 b) Explain what is meant by a change of state.
 c) Explain why the temperature of the ice remains constant during this
change of state.

Answer

a) Ice is a solid, so to begin with the molecules are arranged in a fixed pattern and
are held in place by strong forces between them. They vibrate around a fixed point,
and are close together. As the ice melts, heat energy is used to break/weaken the
bonds between the molecules, allowing them to move more freely with only weak
forces between them. They stay close together, moving randomly.

b) A change of state occur when a substance changes between a solid, liquid or gas
state. For example, the ice cube changes state from solid to liquid as it melts.

c) Normally, heating a substance increases the temperature as the K.E. of the

molecules increases. During a change of state, the heat energy supplied is used to
break or weaken the bonds between the molecules with no increase in K.E., and
therefore no change in temperature.

64
Evaporation
Is the escape of more energetic molecule from the surface of liquid, these
molecule will be able to overcome the intermolecular force with neighbor molecule
and escape so reaming molecule of liquid has less kinetic energy and cool

Evaporation Boiling
Surface molecule only Whole the liquid
Any Temperature Specific Temperature
No Bubbles Bubbles

Factors affecting Evaporation

1. Temperature (Heat) as it increases, the rate of evaporation increases. This is
because the molecules move faster, so more of them have enough energy to escape
from the liquid within the same time.

2. Surface area as it increases, the rate of evaporation increases. As this gives the
faster molecules a greater chance of escaping

3. Air currents over the surface of the liquid as it increases

(Increase draught) the rate of evaporation increases. When air moves across a
liquid surface, it carries away molecules escaping from the liquid and reduces their
chances of returning to it.

4. Humidity as it increases, the rate of evaporation decreases. Otherwise, Molecules

escaping from a liquid have lower chances of returning to it if the humidity is low.
 During evaporation, the liquid loses its most energetic molecules, leaving
behind the less energetic ones. Therefore, the average kinetic energy of the
remaining molecules decreases, accordingly, the liquid’s temperature

65
 decreases. This explains the cooling of a body in contact with an evaporating
liquid. This is known as cooling effect due to evaporation.

Brownian motion
Is an evidence for the continual motion of particles in a liquid or a gas
It shows that massive particles may be moved by light, fast moving particles

Procedure
1. Fill the smoke cell (or glass cell) with smoke.
2. Replace the lid on the cell and set it on the microscope
platform.
3. Switch on the lamp; focus the light on the smoke.

Observation
Finding bright specks of light moving about in a random

Conclusion
The air molecules are: very tiny, moving randomly about and their motion is
much faster than that of the smoke particles.

Explanation
The smoke particle in air is being hit by air particle from all direction (as air has
kinetic energy) so smoke particle move in random straight line

 The same experiment can be carried out by sprinkling some pollen grains in
water and observing the motion of the pollen grains.

66
Pressure by Gas

 All moving particles have kinetic energy and momentum Gas molecules have
large energies (because they are moving very fast).

 The average kinetic energy is related to the temperature of the gas.

Increasing the temperature of a gas increases the average kinetic energy of
particles within that gas and they move faster.

 The gas particles exert a force on the walls of a container when they collide
with it. The pressure exerted by the gas particles is the force per unit area.
The total pressure of the gas is the effect of the sum of all the collisions with
the wall.

 When the molecules collide with the walls of the container they change
direction and bounce back. This means that the velocity (a vector quantity)
has changed. If the velocity changes, the momentum changes.

 The force is larger if the particles are moving faster (because the change in
momentum is greater) or if there are more particles colliding with the walls
per second.

 A higher temperature gases more collisions in a given time and causes the
collisions to be harder because the particles are moving faster.
Consequently, a higher temperature causes a larger pressure.

67
Boyles’s Law

Boyle's Law states that

 For a fixed mass of gas at constant temperature, the pressure is inversely

proportional to the volume.

 This means that for a fixed mass of gas at constant temperature, the
pressure multiplied by the volume is constant p× V= constant
 When the pressure increases, the volume decreases and vice versa, as shown
in the graph below.

 By add mass on piston the pressure increases because the gas molecules
are squeezed into a smaller space volume decrease Therefore there are
more collisions per second between the
molecules and the container walls. The
more frequent collisions cause a larger
force on the walls and hence a larger
pressure.

68
  pressure and volume are related by equation

p1 v1 = p2 v2

Questions

1. An aerosol can contain a fluid under pressure. Explain why it is dangerous

to expose the can to high temperatures.

Answer

If you increase the temperature, the pressure inside the can increases further.
This could cause the can to break open or even explode in high temperatures.

2. A diver is deep under the sea. When divers breathe out, they release
bubbles of gas which rises to the surface. Explain what happens to:

 a) The pressure in the water surrounding a bubble as it rises to the

surface.
 b) The volume of a bubble as it rises to the surface.

Answer

a) The pressure in water depends on the height (h) of water above that point due to
the formula P = ρ g h.
Therefore as a bubble rises, h decreases, and so the pressure decreases.

b) If the pressure of the water decreases as a bubble rises, then the pressure on the
gas bubble also decreases. If the pressure decreases, the volume increases.

69
3. A syringe contains 10 cm3 of air at a pressure of 100 kPa.

 a) Calculate the new pressure in the syringe when the gas is

compressed to a volume of 4 cm3.
 b) State one condition required for the calculation above to be true.

Answer

a) P1 x V1 = P2 x V2
Substituting in values for the initial volume (10 cm3) and pressure (100 000 Pa), and
the final volume (4 cm3) gives:
100 000 x 10 = P2 x 4

1 000 000
P2 =
4

So the final pressure P2 = 250 000 Pa

b) This formula only applies if the temperature or mass of gas remains constant.

4. A diver descends to a depth of 40 m, breathing air that is at a pressure of

500 kPa. The diver's lungs have a total volume of 0.006 m3.

a) Calculate the volume the air in the diver's lungs would occupy at the
surface, where the pressure is only 100 kPa.

b) Suggest why it is dangerous for divers to hold their breath whilst swimming
upwards to the surface.

70
Answer

a) P1 x V1 = P2 x V2
Then substituting in values for the initial and final values gives
500 000 x 0.006 = 100 000 x V2

500 000 x 0.006

V2 =
100 000

So the final volume of air at the surface will be V2 = 0.03 m3.

b) This volume is 5 times larger than the volume of the lungs. The diver is in danger
of causing damage to his /her lungs or even rupturing them, as the air expands
outwards.

Temperature and pressure

 The pressure of a fixed volume of gas is related to its temperature. As the

temperature increases, so does the pressure. When the temperature of a
gas is increased the internal energy of its molecules increases. The
molecules move faster because the average kinetic energy of the molecules
increases.

 The pressure of the gas is determined by the force of the particles colliding
with the walls of the container and by the rate of collision. As the
temperature increases, the force increases and so the pressure of a gas
increases with temperature.

71
  As the volume of the container is kept constant, there will also be more
molecules hitting the walls of the container every second and so the
pressure is increased

Decreasing temperature and pressure

When the temperature of a gas is decreased the average kinetic energy of the
particles decreases. The temperature at which particles can be considered to be
stationary is called absolute zero this corresponds to a temperature of -273°

The zero of the Kelvin scale is absolute zero, the lowest possible temperature

𝑡𝑒𝑚𝑝𝑒𝑟𝑎𝑡𝑢𝑟𝑒 𝑖𝑛 𝐾=𝑡𝑒𝑚𝑝𝑒𝑟𝑎𝑡𝑢𝑟𝑒 𝑖𝑛 ℃+273

72
Questions

1. Scientists are studying the conditions found on the planet Mars.

 a) One block of frozen CO2 is at a temperature of 150 K. What is this

temperature in degrees Celsius?
 b) Surface rocks can get as warm as 20 0C in the day time. What is this
temperature in Kelvin?

Answer

a) The temperature will be 150 K - 273 = -123 0C

b) The temperature will be 20 0C +273 = 293 K

Thermal Expansion
When matter is heated, it expands (volume increases). When it is cooled, it
contracts. Higher temperatures of a substance mean greater speed of molecules
and bigger vibrations. Accordingly, spacing between molecules increases causing
expansion.

a) Expansion in solids
When a solid is heated, its atoms vibrate faster about their fixed points. The relative
increase in the size
 For railway tracks Gaps are left between lengths of rail to allow for expansion
in summer.
 For cables: provide sagging between telephone poles to allow for contraction of
cables.

73
 Bimetallic strips: Strips of iron and copper or brass
, brass expands more than the Iron. It is mostly used
in fire alarm and thermostat (metal).

b) Expansion in Liquid
Liquids expand for the same reason, but because the bonds between separate
molecules are usually less tight they expand more than solids. This is the
principle behind liquid-in-glass thermometers. An increase in temperature results in
the expansion of the liquid which means it rises up the glass

c) Expansion in gas
Molecules within gases are further apart and weakly attracted to each other. Heat
causes the molecules to move faster,

“Expansion of a gas more than the volume of liquid and, liquid is more than
solid “

Specific heat capacity

By increasing temperature the internal energy of substance increase, as
temperature increase kinetic energy of molecule increase

Specific heat capacity (c)

It is the amount of energy needed to raise the temperature of 1 kg of a substance by
1 ºC It is measured in J/kgºC

When there is no change of state, the heat lost or gained by an object can be
calculated
𝐸 = 𝑚 𝑐 Δ𝑇

74
Where
 E is the quantity of heat energy, measured in J. note that heat energy supplied by
an electric heater is given by: 𝐸𝑛𝑒𝑟𝑔𝑦=𝑝𝑜𝑤𝑒𝑟 ×𝑡𝑖𝑚𝑒
 m is the mass of the object in g or kg
 c is the specific heat capacity of the material in J/kgºC or J/kgK.
 ΔT is the change in temperature in ºC or K since as the change in temperature of
1 ºC equals the change in temperature of 1 K and is always expressed as (Tf - Ti).

Finding specific heat capacities (solid)

1. Record the power of the electric heater.

2. Find the mass (m) of the aluminum block (1kg)
3. Using a thermometer, measure and record the
initial temperature of water (Ti) before
switching on the heater.
4. Start the stop watch as you switch on the heater.
5. After a certain time, switch off the heater, record
the time (t) on the stop watch and record the
final temperature (Tf).
 if the temperature rise is too large then too much heat will be lost.
6. Calculate the temperature rise Δ𝑇=𝑇𝑓− 𝑇𝑖 and the quantity of energy supplied as
heat
7. The specific heat capacity can be calculated using the following formula

c=

Improvement
 put insulating material around the aluminum block ( to reduce heat lost )
 put oil in the gap of the aluminum block (to ensure thermal conduct
between aluminum and thermometer )

75
Finding specific heat capacities (liquid)
1. put 0.25 kg of water into beaker
2. setup the experiments as shown in figure
3. measure and record the initial temperature(Ti)
of the block
4. turn on power supply and leave until the
temperature change by about 50 Co
5. turn off power supply record final temperature
(Tf)
6. calculate the change in temperature Δ𝑇=𝑇𝑓− 𝑇𝑖
7. record joule meter reading and calculate specific heat capacity by equation

c=

Questions

1. A kettle is filled with 2.5 kg of water of S.H.C. 4180 J/kg 0C. Calculate the
energy needed to heat the water from a room temperature of 25 0C to the
boiling point at 100 0C .

Answer
ΔQ = m x c x ΔT
ΔQ = 2.5 x 4180 x (100-25)
ΔQ = 784 000 J (784 kJ)

2. An investigation is carried out to find the S.H.C. of a 1 kg copper block. The

block increases from 22 0C to 61 0C with 16 400 J of heat energy transferred.

 a) Show that the S.H.C. of copper is about 400 J/kg 0C

76
  b) The heating element has a power output of 48 W. Calculate the time
it takes to heat the copper to 61 0C.

Answer

a) ΔT is 61-22 = 39 0C. Rearranging the formula for S.H.C. gives

ΔQ
c= 16 400
m x ΔT c=
1 x 39

c= 421 J/kg 0C

b) we know that power and energy /work are related by the formula

W 16 400
t= t= t = 341 seconds
P 48

3. Ice cubes of mass 60 g are placed into a glass of 300 g of water. The ice is
initially at -18 0C and warms up to -1 0C over a period of 4 minutes. Ice has a
S.H.C. of 2110 J/kg 0C.

 a) Calculate the heat energy gained by the ice during this time.
 b) Calculate the temperature drop of the water as heat energy is
transferred to the ice. The S.H.C. of water is 4180 J/kg 0C.
 C) Suggest one reason why the answer in (b) may be unrealistic and
incorrect.

Answer

a) ΔQ = m x c x ΔT, and m= 60 g = 0.06 kg

Therefore for the ice,
ΔQ = 0.06 x 2110 x 17= 2150 J

77
b) The heat energy to warm the ice comes from the surrounding water. Therefore
the water cools, losing the same quantity of heat energy.
As ΔQ = m x c x ΔT , then using m = 0.3 kg gives

ΔQ 2150
ΔT= ΔT=
mxc 0.3 x 4180
ΔT = 1.71 0c

c) The water may not cool by 1.71 0C due to any of the following:
Glass cools down as well / heat gain or loss due to surroundings / some ice may
melt / ice may not cool by the same temperature drop across the cubes

Heat / Thermal Energy Transfer

Thermal or heat energy is a form of energy possessed by hot matter. Hot, Thermal
energy travels from a body/place that is hotter (at a higher temperature) to a
body/place that is colder (at a lower temperature). Thus, the cold object warms
up by receiving heat energy and the hot object cools down by losing heat energy till
thermal equilibrium takes place.
The transfer of thermal energy between bodies/places that have different
temperatures can occur in three ways conduction, convection and radiation.

Conduction
Thermal conduction is the transfer of thermal (heat) energy through a substance
without the substance itself moving.

There are 2 methods by which conduction can take place

78
1) Collisions between neighboring particles
When heat is applied to a substance, the kinetic energy of its atoms increases so
their vibrations get bigger. The vibrating atoms bump into neighboring atoms
and pass on their kinetic energy. These atoms then pass on their kinetic energy to
atoms close to them and so on. In such way, the heat energy moves through the
substance. Conduction takes place in solids, liquids and gases, but it works best in
solids as their molecules are closer together.

2) Flow of free electrons (for heat conductors only)

Metals are the best solids for conducting heat since they have free moving
electrons. When a metal is heated these free electrons gain kinetic energy and move
towards the other cooler parts of the metal, accordingly, spreading the energy to
these cooler parts. This process is fast and that’s why all metals are good
conductors of heat.

 Conduction in solids is better than in liquids than in gases.

 Liquids (water) and gases (air) are poor conductors as the spacing between
their molecules is much greater than in solids.
 All Metals are good conductors of heat due to presence of free electron
 Vacuum does not conduct heat, as there are no molecules in vacuum to pass
the kinetic energy on.

79
  During heat transfer by conduction, the molecules do not change their
positions within the substance.

Poor Conductors
 They do not possess free moving electrons. When such substances are heated,
the kinetic energy of the molecules increases and
they move faster and bump into their neighboring
molecules giving them part of their kinetic energy.
Here, this is a much slower process, that’s why
these substances are called poor conductors or
insulators of heat.
 Generally, most non-metal solids, almost all
liquids (except mercury) and gases are poor
conductors of heat.
 This figure shows that water is a poor conductor of heat.

Convection
Convection is the transfer of heat through fluids (liquids and gases) by the upward
movement of warmer, less dense regions of fluid.

 When a mass of liquid (or gas) is heated, the heated liquid expands and become
less dense than the colder surrounding liquid so it floats up to
the top of the container. Colder liquid sinks to take its place,
and is then heated too. At the top, the warm liquid starts to
cool, becomes denser again and will begin to sink, so a
circulating current is set up in the liquid. This is called
convection current




80
 Convection cannot occur in solids as the molecules are not free to move about
within the solid structure.
 Convection cannot occur in vacuum as there are no molecules to transfer heat
by convection.
 Convection cannot occur if the fluid is heated at the top rather than at the
bottom. The warmer, less dense fluid simply stays at the top.

Why heat transfer by convection is possible in liquids and gases?

Because the molecules of liquids or gases are free to move around so they can
transfer the heat through convection currents.

Radiation
Thermal radiation is the transfer of energy by infra-red (IR) waves unlike
conduction and convection (both need matter to occur), radiation can occur in
vacuum. In radiation, heat energy is transferred by infra-red waves – one of the
electromagnetic spectrum. Radiation is emitted by all objects in all directions, at
the speed of light (3×108 m/s). The amount of radiation emitted depends on the
1. Surface temperature
2. Surface area of the body


 Highly polished silvered shiny light
colored surfaces are good reflectors of
thermal radiation
(Are poor emitters and poor absorbers)
 Dull matt black and dark surfaces are poor reflectors of heat radiation
(Are good emitters and good absorbers)

81
Experiment Good and bad absorbers of
radiation
1. Two flasks are used, one covered with dull (matt) black paint
and the other with shiny white paint.
2. Both flasks contain the same amount of water, at the same
Temperature and are placed at equal distances from a radiant
heater.

Results
The temperature of the water in the flask with the dull black surface is found to rise
significantly more than the flask with the light shiny surface.

Conclusion
Dull dark matt surfaces are the best absorbers; shiny mirror-like surfaces are the
poorest.

Applications on Heat Transfer

1) Vacuum flask
A vacuum flask has several features to reduce flow of
thermal energy, and will keep liquids hot (or cold) for
several hours.
 Transfer by conduction is minimized by making the
flask double-walled glass vessel with vacuum
between the walls.
 Heat loss by convection and evaporation is reduced
by using a stopper.
 Radiation is reduced by silvering both walls on the vacuum side.

82
2) Windows are double or triple glazed
Two or three layers of glass with vacuum in between or with a moderate layer of air
trapped in-between this reduces heat loss by conduction, convection and not
radiation

3) Car radiator cools the engine

In a car radiator, the coolant liquid flows through the tubes inside combustion engine and
absorb the engine's heat and in-turn gets heated itself

The heated fluid then makes its way through a rubber hose to the radiator in the front of
the car. As it flows through the thin tubes in the radiator, the hot liquid is cooled by the air
stream entering the engine compartment from the grill in front of the car. Once the fluid is
cooled, it returns to the engine to absorb more heat.

The air picks up heat from the coolant by convection process, heated air is blown away by
the fan, and colder air replaces it.

83
4) A fire burning wood or coal

When coal or wood is burnt the chemical combustion releases infra-red radiation,
in addition the air close to fire heat and rises so thermal energy transfer to
surrounding by convection, energy transfer by conduction to object in contact
with burning fuel

84
 3-Waves
Waves
Waves are a means of transferring energy from one place to another through
vibrations without transferring matter

Types of waves
1) Mechanical waves
These are waves that require a medium to travel through; they cannot travel
through vacuum.
Sound waves ripple waves and slinky spring waves. These waves are either:
transverse or longitudinal.

2) Electromagnetic waves
These are waves that do not require a medium to travel through and can travel
through vacuum.
Radio waves, X-rays, infrared waves… All electromagnetic waves are transverse.

 Waves can be classified according to how the particles vibrate relative to the
direction of wave propagation into two categories transverse or longitudinal

1) Transverse waves
A transverse wave is one that vibrates or oscillates at right angles (perpendicular)
to the direction in which the energy or wave is moving light waves and waves
travelling on the surface of water.

 This can be shown by a slinky spring: give one end a quick wiggle at right angles
to the spring the coils of the slinky are vibrating up and down “across” the
direction

85
2) Longitudinal waves

A longitudinal wave is one in which the vibrations or oscillations are along

(parallel to) the direction in which the energy or wave is moving, sound waves.

Longitudinal waves are recognized by their compressions and rarefactions.

 This can be shown by a slinky spring: push and pull the end of a slinky in a
direction parallel to its axis the coils of the slinky are vibrating in the directions
that are along its length.

Questions

1. A wave produced on a long rope is a transverse wave.

 a) Explain what is meant by a transverse wave.

 b) Give one other example of a transverse wave.
 c) Give one example of a longitudinal wave.

86
Answer

a) A transverse wave is where the particles/disturbance moves at 900 -

perpendicularly - to the wave motion.

b) Water (surface) waves, Light (or any electromagnetic wave) are all transverse
waves.

c) Sound is the most common example of a longitudinal wave.

Wave properties
Amplitude (A)
The amplitude ‘A’ is the maximum height of wave from rest position

Wavelength (λ)
The wavelength of a wave, represented by the Greek letter λ (lambda), is the
distance between the two successive points (crests or troughs).

Frequency (f)
The frequency f is the number of complete waves generated per second. The unit of
frequency is ‘cycle per second’ or hertz (Hz). Where 1 Hz = 1 wave/second

87
Time period (T)
It is the time taken for a wave to complete one cycle or one wave.

The frequency and the period are related by the following equation

𝑓=
Questions

1. Ocean waves hit a wall in a harbor at a rate of 12 waves per minute. What is
the frequency of these waves?

Answer

If there are 12 waves per minute, then we have 12 waves per 60 seconds.
The frequency is defined as the number of waves per second, so we need to divide
12 by 60

12
frequency =
60

Frequency = 0.2 Hz (hertz)

2. A guitar string produces a sound of frequency 1.2 kHz. What is the time
period of this wave?

Answer

1.2 kHz is equal to 1200 Hz. using the formula above, the time period is therefore:

1
time period =
1200

Time period = 0.000833 s

88
Wave fronts
The wave front can generally be thought of as continuous line,
perpendicular to direction of propagation, like view sea waves from
top of cliff (Straight lines and can be thought as the crests or
troughs of the waves)

Wave equation
The higher the frequency (f) of a wave the smaller its wavelength (λ) It is true for all
types of waves and the relation between them is called wave equation which is
Speed of wave = wave length x frequency
v=fxλ

Questions

1. Sound waves have a velocity of 340 m/s in air. A car horn in a stationary car
makes a sound of frequency 500 Hz.

 a) Calculate the wavelength of the sound produced.

 b) Describe how the frequency of the sound changes if the car moves
quickly away from the observer.

Answer

a) We know that v = ƒ x λ, so the wavelength λ is

v 340
λ= λ=
ƒ 500

λ = 0.68 m

89
b) As the car moves away from the observer, the frequency decreases (because the
pitch we hear is lower).

Behavior of waves
1) Reflection
Change in direction of wave when it meets a hard boundary (mirror)
Law of reflection
“The angle of incidence is equal to the angle of reflection”
i=r
Where
The angle of incidence (i) is the angle between the
incident ray and the normal.
The angle of reflection (r) is the angle between the
reflected ray and the normal.
The normal is a line drawn at right angles to the
surface.

 When a wave is reflected, it is still in the same medium so its speed doesn’t
change. Accordingly, its wavelength doesn’t change.

Questions

1. The diagram below shows a mirror angled at 300 to a

flat table. A ray of light is directed vertically down onto
the mirror as shown here:

On the diagram shown above

 a) Draw a normal line to the mirror at the point

where ray hits the mirror.
 b) Draw the reflected ray.

90
  c) Measure or calculate the angle between the incident and reflected
ray.

Answer

a) The normal line should be (approximately) perpendicular

to the mirror.

b) The reflected ray should be above the horizontal. It should

be drawn so that the normal line is (approximately) in the
center of incident and reflected ray.

c) The angle between the incident and reflected rays should be 600. This can be
measured, or you could calculate it by extending the normal line

Reflection of light
When light reflects from a plane mirror, the angle of incidence (i) is equal to the
angle of reflection (r); the law of reflection is applied.
This figure shows how an image is formed behind a plane mirror. Two rays from any
point on the object are sufficient to establish the position of the image of that point.

Properties of the formed image

1. The image is virtual it is formed by the extension of the real (reflected) rays.

 Solid lines represent real rays whereas dashed lines represent virtual rays.
2. The formed image has the same size as the object.

3. The image is as far behind the mirror as the object is in front (same distance)

4. It is laterally inverted.

5. It is upright.

91
Circular waves (reflection)
The reflected waves are also circular and appear to come from a corresponding
image point at the same distance behind the reflector as the point source is in front
of it.

2) Refraction
is the change in both speed and wavelength of a
wave as it travels from one medium to another or
the bending of a wave due to change in its speed as it
moves from one medium to another.

92
Remember this
a) If the incident ray is lying along the normal (the ray is perpendicular to the
boundary or the angle of incidence = zero), then no bending occurs.

b) If the wave comes from a less dense medium to a more dense medium, then its
speed decreases and it bends towards the normal (i>r).

c) If the wave comes from a more dense medium to a less dense medium, then its
speed increases and it bends away from the normal (i<r).

Where,
i is the angle of incidence (the angle between the ray incident to the boundary and the
normal) and r is the angle of refraction (the angle between the refracted ray and the
normal).

 When water waves pass across a boundary, from deep water (less density) to
shallow water (more Density) they move slower in the shallow water

93
3) Diffraction
Is the spreading out of waves as they travel through a gap or round a corner

 If the waves pass through a narrow gap which is equal to or smaller than the
wavelength of the wave, then there are waves to the left and right of the gap
“complete diffraction”.

 If waves pass through a large gap, the majority of the waves passing through
the gap continue in straight line “small/partial diffraction”.

 The narrower the gap, the more the waves spread out “ more diffraction”
 In all diffraction cases, the wavelength and frequency do not change.
Accordingly, the speed does not change.

94
Summary

reflection refraction diffraction

speed Stays the same Increase/ decrease Stays the same

wavelength Stays the same Increase/ decrease Stays the same
Frequency Stays the same Stays the same Stays the same

Refractive index
 It is a ratio that has no unit

Refractive index =

 Speed of light (3×108 m/s).

Experiment to show refraction of light

1-Place a transparent block in the middle of a plain sheet of paper; trace around the
block in pencil.
2-Position a ray box so that the light from it strikes the glass block at an angle.

95
3-Mark the positions where the light meets the glass boundary and where it leaves
the glass boundary with dots
4-Mark two crosses (or place optical pins) on the paper along the incident ray and
the emergent ray approximately 5cm apart.
5-Remove the glass block and switch off the ray box.
6-Using a ruler, complete the lines between the dots and the crosses.
7-Draw in the normal at 90° to where the light strikes the glass boundary.
8-Draw the second normal where the light leaves the glass boundary, again at 90°.
9- Using a protractor, measure the angles of incidence and refraction as shown on
the diagram above.

Critical angle

Waves going from a dense medium to a less dense medium speed up at the
boundary between them. This causes light rays to bend when they pass from glass
to air at an angle other than 90°. This is refraction.

Beyond a certain angle, called the critical angle, all the waves reflect back into the
glass. We say that they are totally internally reflected

96
 critical angle ( I = c ) is the incident angle when the refracted ray at the top of
the prism

n=

Total internal reflection

If the angle of incidence “ I “ is more than critical angle “c” (i>c) all the light is
reflected back at the boundary and no light is refracted. The ray experiences “total
internal reflection”, this takes place only in the denser medium.

Uses

1-communcation

Mobile phones and internet transmit information digitally (0,1) in form of light
pulses by total internal reflection

2-medical

Endoscope is a device used to view inside stomach of a patient

Consist of two fibers:

fibre 1 transfer light from outside of the body to the inside

fibre 2 transfer image from inside to the outside

97
3-periscope

The inside of glass prism can be used as mirror, total

internal reflection take place on the longest face of
prism as shown in figure

Questions

1. A light ray is incident on the surface of a glass of water with an angle of

incidence of 250. If the refractive index of water is 1.33, calculate the angle of
refraction of the light ray.

Answer

We know that n = 1.33, and i = 250. Using Snell's Law we get

sin 250
= 1.33
sin r

rearranging this and finding

0.423
sin r =
1.33

So sin r = 0.318,
r = sin -1 (0.318)
r = 18.50 , or 190

98
2. The diagram below shows a Perspex block with a refractive
index of 1.5.

Calculate the angle of incidence i that produces this refracted

ray with an angle of refraction of 380.

Answer

We know that n = 1.5, and r = 380. Using Snell's Law we get:

sin i
= 1.5
sin 380

sin i = 1.5 x sin 380

sin i = 0.93
i = sin-1 0.93
i = 670

3. Water has a refractive index of 1.33.

 a). Calculate the critical angle of water.

 b). Describe and explain what will happen to a ray of light travelling
upwards through water, hitting the surface with an angle of incidence of
500.

Answer

a) Using the formula above, and n= 1.33 gives

1
sin C =
1.33

99
sin C = 0.75
C = sin-1 (0.75)
C = 48.60

b) At an angle of incidence of 500, the ray will be reflected, because this angle
is greater than the critical angle calculated in part (a).

LENSES
They are divided into two types
1. Convex or converging lens is thicker at the middle than the edges.
2. Concave or diverging lens thicker at the edge than at the center.

Principal axis
The straight line passing through the center of the lens is called principal axis.

Focal point or Focus

A point at which incident rays parallel to the principal axis of a lens converges
Focal length
The distance from the optical center to the focus

100
Drawing ray diagrams

1-Draw a ray from the top of the object through the Centre of the lens, which does
not change direction
2-Draw a ray from the top of the object parallel to the principal axis until it reaches
the central plane of the lens. The ray then passes straight through the principal
focus on the other side of the lens. An image is formed where the rays meet

101
A converging lens can be used as a magnifying glass when an object is placed
between F and the lens , image describe as ( upright , virtual , enlarged )

 real image it can be formed on screen

 virtual image can’t be formed on screen

102
103
104
105
106
107
Eye

The normal human eye has a lens that converges light to form an image on the light-
sensitive membrane at the back of the eyeball called the retina. The image is
converted to an electrical signal, which is relayed to the brain via the optic nerve to
translate the image into something meaningful. The focal length of the eye lens
is very short - less than 20 mm - the distance from the lens to the back of the eyeball.

 If a person has normal sight the image is formed on the retina.

 If a person has short-sight (myopia) the image is formed in front of the
retina
 if a person has long-sight (hypermetropia) the image is formed behind the
retina.
 If the image is not formed on the retina the brain cannot translate the image
into something meaningful and the person sees a blurred image.

108
  short sighted
Can see close object but object faraway are blurred, to
correct short sighted diverging lenses can be placed in
front of eyes

 long sighted
Can see object a long way away but object close by are
blurred, to correct long sighted converging lenses can be
placed in front of the eyes

Dispersion of white light

When white light falls on triangular glass prism a band

of colour called spectrum is obtained. The effect is
called dispersion. It arises because white light is
mixture of seven colours which the prism separates
because the refractive index of glass is different for
each color

 red colour is the lowest frequency , violet is the highest frequency

 monochromatic means single colour , single frequency
 The spectrum of colors can be recombined through the following arrangement

109
Electromagnetic spectrum
A spectrum of different wavelengths this spectrum includes visible light, X-rays and
radio waves. Electromagnetic radiation can be useful as well as hazardous

Properties of E.M. waves

All of these waves have some key identical properties

 They all travel at the same speed (the speed of light) in a vacuum.
 They are all transverse waves.
 They are all electromagnetic waves.

They can all be reflected and refracted

Region of E.M.
Uses Dangers
spectrum

broadcasting,
radio -
communication
cooking, internal heating of body
microwaves
satellite communication tissue
heating,
infrared night vision , remote skin burns
control
photography,
visible skin burns
fiber-optic communication

110
 fluorescent lamps blindness,
ultraviolet
and inks damage to surface cells
observing internal
structures, damage to internal cells
x-rays
for medicine and and organs
materials
sterilizing food mutation of cells,
gamma rays
and medical equipment cancer

Communication

 Communication with artificial satellites usually uses microwaves because

they can pass straight through the atmosphere. An artificial satellite is a
human-made satellite that orbits the Earth. Some satellite phones and
television broadcast systems use microwaves to communicate with low
level artificial satellites.

 Most communications satellites occupy a geostationary orbit, they remain

above the same point on Earth as they orbit. This means that a signal can be
pointed at the artificial satellite and that a link can be established between
that point on Earth and the satellite so that information can be passed
between them.

 mobile phones (cell phones) and wireless internet use microwaves because
microwaves can penetrate some walls and only require a short aerial for
transmission and reception

 Bluetooth uses radio waves because radio waves pass through walls but the
signal is weakened on doing so

111
  optical fibres (visible light or infrared) are used for cable television and
high-speed broadband because glass is transparent to visible light and some
infrared; visible light and short wavelength infrared can carry high rates of
data

Analogue and digital signals

a) Analogue signals
A signal whose properties change continuously with time and can have any value,
thermometers, speedometers and old-fashioned watches

b) Digital signals
A signal that consists of a voltage that can have one of only two values “High and
low” or “On and Off” or “0 and 1” , digital clocks and digital meters

Advantages of using digital signals

1. high quality of video and video file
2. cheaper and more available electronics
3. higher security due to encryption of data
4. extra added bits for error checking

112
Sound
✓ Sounds are produced by objects that
are vibrating.

✓ Sound is a form of kinetic energy

which travels in the form of waves.

 Sound waves is longitudinal consist of a series of :

 compressions (air molecules pushed closer together at a slightly higher
pressure)
 Rarefactions (air molecules are farther apart at a slightly lower
pressure).

Measuring the speed of sound

The speed of sound in air is approximately 340 m/s. In liquids 1500 m/s and solids
5000 m/s the particles are much closer together. This means that they are able to
transfer sound energy more quickly. So sound travels faster in solids more than
liquids more than gases

Speed of sound
gas 340 m/s
liquid 1500 m/s
solid 5000 m/s

 two people (person A and person B) are placed a

distance apart, 100 meters by measuring tape

 person A fires a starter’s pistol

 person B times the difference between seeing the

113
 flash of the gun and hearing the sound - this is measured in seconds

Where,

𝑠𝑝𝑒𝑒𝑑 𝑜𝑓 𝑠𝑜𝑢𝑛𝑑 =

Human Hearing
Humans can hear a wide range of frequencies. The lowest sounds that we can
detect are about 20 Hz. The highest sounds for a healthy young adult are about 20
000 Hz or 20 kHz.

 less 20 Hz is infrasound
 more 20000 Hz ultrasound

Loudness and amplitude

The amplitude of a wave gives us
some idea of the energy it is
transferring. For a sound wave, its
amplitude is a measure of its
loudness.

Pitch and frequency

The frequency of a source is the
number of complete vibrations it
makes each second and is
measured in Hertz (Hz). Objects
vibrate quickly and produce sound
waves with a high frequency. The
sounds are heard as high pitch.

114
Questions

1. The diagram here shows a wave displayed on an oscilloscope

screen. Add a second wave on the diagram to show a wave with a
higher pitch and louder than the original sound.

Answer

 Taller than the original, showing a higher amplitude and

therefore higher volume,
 Closer together than the original (more than 4 peaks in
the box), showing a higher frequency and therefore a
higher pitch.

 Boats use a SONAR (Sound Navigation and Ranging) system to locate objects
such as shipwrecks and shoals of fish beneath the surface of the sea, and to
measure the depth of the ocean. An ultrasound pulse is sent from the boat to the
object and the time taken for the pulse to reach the object and return to the ship,
together with the speed of sound in seawater, enables the distance to be
calculated.

115
 Ultrasound scanning can also be used to diagnose problems with various
organs in the body, such as the heart, liver and kidneys. It is a non-invasive
technique, i.e. doctors do not have to operate on patients to be able to 'see' what
is inside them, and it does not have the same risks as X-rays.

 Ultrasound scanning can also be used to search for defects in metals, pipes and
other materials. If an ultrasonic pulse is aimed through a sheet of metal it
would be expected to send an echo back from the far side, but if there is a crack
within the metal an echo is sent back sooner than expected as shown below.

116
 4-Electricity and Magnetism
Magnetism
Properties of Magnets
 Objects made from magnetic materials called
ferrous materials or ferromagnetic (such as iron,
steel, nickel and cobalt) can be magnetized or
attracted by a magnet.
 Objects made from non-magnetic materials called non-ferrous materials
(such as plastic, wood, paper or rubber) cannot be magnetized or attracted to
magnets.
 The parts of a magnet where the magnetic force is the strongest are called its
poles (as we move Away from the poles, the magnetic force strength decreases).
 The poles of a bar magnet are near its ends and occur in pairs of equal strength
(a north pole and a south pole).
 When a magnet is suspended freely, its north pole will point towards the
north of the Earth and its south pole will point towards the south of the Earth

Magnetic forces

“Similar poles repel and opposite poles attract”

117
Magnetic Fields
The magnetic field is the region around a magnet where magnetic force can be
detected. This region contains the magnetic flux which is represented using lines of
force or flux lines.
Magnetic flux is a vector quantity, so flux lines should represent both magnitude
and direction,
Accordingly they
1. Show the shape of the magnetic field.
2. Show the direction of the magnetic field (field lines travel from north to South
Pole).
3. Show the strength of the magnetic field (the closer the lines the stronger the
field).

To investigate the magnetic field of a bar magnet

1. Place a sheet of paper on top of a bar magnet.
2. Sprinkle iron filings on the paper and tap the paper gently to allow for
redistribution.
 The iron filings align themselves according to the shape of the magnetic
field

118
To investigate Direction of magnetic field of a bar
magnet

1. place the plotting compass near the magnet on a piece of

paper

2. mark the direction the compass needle points

3. move the plotting compass to many different positions in

the magnetic field, marking the needle direction each time

4. join the points to show the field lines

The magnet could be either one of two types

Induced Magnetism
A magnet is placed near a magnetic substance so that the magnetic substance
attracted to the magnet and act as magnet, both iron and steel are magnetized by
induction but there are some differences:

119
 More iron filings cling to iron than to steel so induced magnetism in iron is
stronger than in steel. Therefore, iron is easier to magnetize than steel.
 When the magnet is removed, iron loses its magnetism easily but steel retains its
magnetism.

Questions

1. The south pole of a magnet is used to test a range of materials. Explain what
will happen when the South Pole is placed near to:

 a) Another south pole.

 b) A copper wire.
 c) A steel paper clip.

Answer

a) Like poles repel, so the other South Pole will repel.

b) Copper is a non-magnetic material, so it will not be attracted or repelled.

c) Steel is a magnetic material so will always be attracted to any magnetic pole.

2. A loudspeaker contains a magnetically soft iron core.

Explain what is meant by a soft magnetic material.

120
Answer

A soft magnetic material can be magnetized easily but quickly loses a magnetic field
/ is a temporary magnet.

3. Describe how to produce a uniform magnetic field between two permanent

magnets. You may add a diagram if needed.

Answer

To produce a uniform field you need two magnets,

with opposite poles facing/next to each other. The uniform region will be between
the two poles.

4. A student tries to demonstrate the magnetic field lines around a permanent

magnet by sprinkling salt crystals on a table mat placed over a strong
permanent magnet.

 a) Explain why no magnetic field pattern is seen.

 b) Suggest an improvement to this investigation, so that field lines can
be seen.

Answer

a) Salt is not a magnetic material. The crystals will not be affected by the magnetic
field.

b) Iron filings should be used instead, and sprinkled slowly on the region around the
magnet.

121
Electric charge
According to the ability of a substance to allow electric charges to flow through it,
substances have been classified into
 Electrical conductor these are substances that allow charges (electricity) to
flow through
Them easily this is because they have free charge carriers, all metals are good
conductors as they have free electrons.
 Electrical insulators these are substances that do not allow electric charges to
flow easily through them. This is because they do not have free charge
carriers, most non-metals plastic, rubber, glass and wood. (except graphite and
silicon)

Determine whether material is conductor or an insulator

1- Set up the circuit as shown to connect a dry cell to lamp via steel paper clip
attached with crocodile clips
2- Observe that the lamp is lit, and conclude that the steel paper clips allow the flow
of charge (current)
3- Replace the steel paper clip with various other materials and observe the
appearance of lamp

122
 There are two methods to obtain static electricity, either by friction of an
insulator or By induction of conductor

1. Charging an insulator by friction (rubbing)

When the uncharged plastic rod is rubbed with an uncharged dry piece of cloth,
electrons from the atoms of the rod may move onto the cloth. Now the charges on
each object are imbalanced. The rod becomes positively charged and the cloth
becomes negatively charged (has excess electrons).

 Only negative electrons can move / the positive protons remain fixed.

Before the experiment After rubbing with the cloth

123
Electric forces between charges and electric fields

a) Electric forces
Charged objects can exert forces on other charged objects without
being in contact with them.
The closer the charges, the greater the force
“Like charges repel and unlike charges attract”

 Attraction exists between charged and

Uncharged (neutral) objects therefore, a neutral object can be attracted to a
positively charged rod and also to a negatively charged rod. Accordingly, attraction
is not considered to be a proof that an object carries a charge but repulsion is
considered to be. Because for repulsion to occur, both objects should have the same
type of charge
“Only repulsion can confirm that an object is charged”
b) Electric fields
An electric field is a region where an object experiences a force
due to its charge,
It is the region around a charge where the force of attraction or
repulsion can be observed by another test charge.
Electric fields are represented by imaginary lines showing the direction of the
force (away from a
positive charge and towards a negative charge). The spacing of the lines shows the
strength of the field. The more closely packed field lines, the stronger
the field
 The field lines caused by the parallel plates are parallel are parallel to
each other and equally spaced. The field is uniform. .
 The field of a point charge is called a radial field and is non-uniform

124
125
Electric current
Electron flow and conventional current
Electric current is the flow of charge (carried by electrons)
 If a cell or battery is connected across the conductor (in a closed circuit), the
electrons flow in the direction away from the negative terminal and towards
the positive terminal. This flow of charge is an electric current.
 The free electrons flow from the negative terminal to the positive terminal of the
battery “Direction of electron flow”.
Whereas the “direction of conventional current” is from the positive terminal to
the negative terminal of the battery

Measuring Electric current

Electric current is the rate of flow of charges.
Electric charge (Q) is measured in coulombs (C). One coulomb of charge is the
equivalent of the
charge carried by electrons.
Electric current is measured in amperes where 1 C/s = 1 A

𝐶𝑢𝑟𝑟𝑒𝑛𝑡 (𝐼) =

126
 The size of the current flowing in a circuit is measured using an ammeter which
is connected in Series with the component of the circuit being investigated

 Ammeters have low resistance so that they measure the size of the
current flowing in the circuit without affecting its value.

Questions

1. A 0.3 amp household lamp is left on for 5 minutes. Calculate the charge
flowing through the lamp in this time.

Answer

In 5 minutes, the time in seconds is 5 x 60 = 300 s,

We know that Q = I x t
Therefore Q = 0.3 x 300
Q = 90 coulombs

2. A 30 mA L.E.D. is left on for some time. During this interval, 6 C of charge

flows through it. How long was the L.E.D. on for?

Answer

30 mA = 0.03 A, or if you are using standard form, 30 x 10-3 A (= 3 x 10-2 A).

If Q = I x t

6
Q
t=
t=
3 x 10-2
I

t = 200 s

127
Voltage (potential difference)
 Cells or batteries transfer energy to the charges as they move them around
circuits. If a 1.5V cell is connected into a circuit, it means that 1.5 Joules of energy
is given to each coulomb of charge that passes through the cell.
 So the potential difference (voltage) between two points in a circuit is the
work done to drive one coulomb of charge between these two points. It is the
energy transferred per unit charge which is measured in Volt (V). 1 Volt = 1 J/C.

𝐸𝑛𝑒𝑟𝑔𝑦 𝑇𝑟𝑎𝑛𝑠𝑓𝑒𝑟𝑟𝑒𝑑
𝑃𝑜𝑡𝑒𝑛𝑡𝑖𝑎𝑙 𝑑𝑖𝑓𝑓𝑒𝑟𝑒𝑛𝑐𝑒 (V) =

 The electromotive force (e.m.f.) of an electrical source is the work done (energy
supplied) by the source to drive 1 coulomb of charge round a closed circuit
(energy gained by each coulomb).

 The potential difference (voltage drop) across a component (or between two
points in a circuit) is the drop in electric potential energy experienced by each
coulomb of charge due to resistance between these two points ( difference in
electrical energy )

Measuring the voltage

 To measure the voltage across a component in a circuit we use a voltmeter
which is connected in parallel with this component.
 Voltmeters have a very high resistance (very little
current flows through it) so that they measure the
potential difference across a component without affecting
the value of the current passing through this component.

128
Questions

3. A kettle needs 20 kJ to boil the water inside. If the kettle voltage is 240 V,
calculate the total charge flowing through the kettle.

Answer

20 kJ is equal to 20 000 J.
We know E = Q x V,

20 000
E Q=
Q= 240
V

Q = 83.333 coulombs

4. A small cell is used to run a camping lamp. The cell stores 180 J of energy,
and is rated as 1.5 V.

 a) What is the total charge that can be delivered by the cell before it
runs out? (Assume when running, the cell voltage remains constant and
the cell is 100% efficient).
 b) The lamp needs 20 mA to operate. Using this information and your
answer from part (a), calculate the time for which the lamp can remain
lit.

Answer

a) If E = Q x V
180
E Q=
Q= 1.5
V

Q = 120 C

129
b) If I = 20 mA (0.02 A) and Q = 120 C,
then using Q = I x t

Q 120
t= t=
I 0.02

t = 6000 s

Ohm’s law and Resistance of a conductor

The resistance of a component is what causes a voltage drop “potential difference”
across this component. The resistance of a conductor is “the ratio of the p.d.
applied across it, to the current passing through it”.
Resistance can be calculated by
𝑃 𝑑 𝑎𝑐𝑟𝑜𝑠𝑠 𝑐𝑜𝑛𝑑𝑢𝑐𝑡𝑜𝑟
𝑅𝑒𝑠𝑖𝑠𝑡𝑎𝑛𝑐𝑒 ( R ) =

 Where R is measured in Ohms (Ω), V in volts and I in amperes. Thus,

1 Ohm= 1 Volt/Ampere

Type of resistor
1-fixed resistor
A resistor which have constant value all the time ( obey ohm’s law )

2-variable resistor (rheostat)

A resistor which has range of value which could be change manually
function: vary the current in the circuit by varying
resistance

130
Measuring the resistance of a resistor
Set up the following experiment
 The voltmeter measures the voltage drop across the
resistor.
 The ammeter measures the current through the
resistor.
 The variable resistor allows you to change the size of
the current

Accordingly note the readings of the ammeter and voltmeter.

Then move the variable resistor and take more readings.

Finally, plot a graph of voltage against current using your readings:

The slope of V against I graph gives the resistance of the wire
( R= V/I )

Ohm’s law
The current that flows through a metallic conductor is directly
Proportional to the potential difference across its ends, provided
its temperature remains constant

Questions

1. A 20 Ω resistor is connected to a 6 V battery. What current flows through it?

Answer

We know that V= I x R, So

131
 V
6
I=
I=
R
20

I= 0.3 A

2. A 4 kΩ resistor has a current of 2 mA flowing through it. What is the p.d.

across the resistor?

Answer

As 1 kΩ = 1000 Ω, then 4 kΩ = 4000 Ω

There are 1000 mA in an amp. So 2 mA = 0.002 A ( 2 ÷ 1000)

p.d. means potential difference - the voltage across the component.

Therefore as V = I x R;
V= 0.002 x 4000
V=8V

3. Two identical resistors R are connected to a 6 V cell as shown. The current

flowing from the cell is 4 A. What is the value of the resistor R?

Answer

In a parallel circuit, the current splits, and here both branches of the
circuit are identical. Therefore 2 amps flows down each branch.
Also for a parallel circuit, the voltage across all branches is the same
as the cell, so each resistor has a p.d. of 6V.

V 6
R= R=
I 2

132
R=3Ω

Four factors affecting resistance

1. As the length increases, the resistance increases so
Rαl
2. As cross-sectional area increases, the resistance decreases.
R α 1/A
3. The resistivity (ρ) of the material
Copper is a good conductor “low resistivity” so used for connecting wires, while
nichelcrom has more resistance, so used in the heating elements of electric fires.
4. Temperature

a) I-V characteristics of Ohmic conductors

 The graph is a straight line passing through the origin , the current flowing
through the wire is directly proportional to the voltage applied across its ends.
This is Ohm’s law.
 The steeper the graph, the lower the resistance and vice versa.
 Copper wire and all other metals “metallic resistors” give this shape of graph,
unless they change temperature.
 The -V & -I show what happens when the battery connections are reversed so
current flows in the opposite direction. Accordingly, values of V & I are negative.
 The graph shows that the conductor has a constant resistance (constant slope)
which is the same for both current directions.

133
b) I-V characteristics of a filament lamp:
 The graph is not a straight line, so the lamp is a non-
ohmic
 Conductor. As more current flows, the metal filament
gets hotter and electron in the wire collide with the
particle inside the wire the electron transfer energy to
the particle therefore internal energy of wire increase

Calculating Electrical power & Electrical energy

To calculate the power used up by any electrical component

𝑃 = 𝐼𝑉 & 𝐸 = 𝐼𝑉𝑡
Using this rule and Ohm’s law, 2 other formulae can be obtained

𝑃 = 𝐼²𝑅 & 𝐸 = 𝐼²𝑅𝑡

𝒗 𝒗
p= & E= t

 energy (E) is measured in joules (J) , power (P) is measured in watts (W)

Questions

1. A 240 V toaster uses a current of 2A.

 a) Calculate the power used by the toaster whilst in operation.

 b) When the toast pops up after 1 minute, the toaster turns off.
Calculate the total energy transferred by the toaster.

134
Answer

a) We know that P = I x V, so:

P = 2 x 240
P = 480 W

b) Firstly, remember to use 60 seconds, not 1 minute.

For this part of the question we can use E = I x V x t
E = 2 x 240 x 60
E = 28 800 J

2. The diagram below shows two heating elements connected in series. The
current flowing through the elements is 2.5 amps.

 a) Calculate the power output of 1 heating element.

 b) Calculate the total thermal energy produced from both elements
over a 5 minute interval.
 Answer

a) The p.d. across each element is 6 V, NOT 12 V.

Using P = I x V gives:
P = 2.5 x 6
P = 15 W each.

b) The total energy is given by E = I x V x t, and the total voltage is 12 V.

5 minutes = 300 seconds, so : E = 2.5 x 12 x 300
E = 9000 J

135
3. A 230 V, 2kW mains kettle is used to boil a litre of water. This requires 340
kJ of energy.

 a) State one difference between mains electricity and the electricity

from a 9V cell.
 b) Calculate the current through the heating element of the kettle.
 c) Calculate the time required to boil the water.

Answer

a) Mains is a.c., whereas a cell is a d.c. supply

b) We know P = I x V

2000
P I=
I= 230
V

I = 8.70 amps

c) E = I x V t

E
t= 340 000 340 000
IxV t= =
8.7 x 230 2000
t = 170 seconds

E 340 000
t= =
P 2000

t = 170 seconds

136
Current in series and parallel circuits
Current in series

 The current at all points around a series circuit is always the same

Current in parallel

 The current in a parallel circuit splits between the branches of the circuit.

Voltage in series and parallel circuits

Voltage in series

137
 The voltage in a series circuit is split (or shared) between the components

Voltage in parallel

 The voltage (p.d) across all components in a parallel circuit is the same

Resistors in series and parallel

Series
If we connect two resistors in series, it makes it harder for current to flow - the
total resistance has increased. In fact, we can just add the value of the
resistors together to find the total resistance.

Parallel
If we connect two resistors in parallel, there are now two paths for the current,
and it makes it easier for current to flow round the circuit. The total resistance
is lower and the current is higher.

138
 Summary
Series connection Parallel connection

 IT = I1 = I2  IT = I1 + I2

 VT = v1 + v2  V T = v1 = v2

 RT = R1 + R2
 = +

Questions

1. Two bulbs, X and Y are connected in series to a 6V cell.

 a) Draw a circuit showing the bulbs and cell. Add an ammeter that is
measuring the current in bulb X.
 b) The current through bulb Y is 500 mA.
i) What is this current in amps?
ii) What is the current through bulb X?

Answer

a) The diagram should look something like this, with all the
components in one loop

b) (i) 1 amp = 1000 mA, so 500 mA = 0.5 A

(ii) As the current is the same at all points, bulb X must also
get 0.5 A current.

139
2. What is the current shown on the ammeters labeled P
and Q in the circuit shown here?

Answer

The cell produces a total current of 0.7 A. If 0.3 amps flows

along the bottom branch, then the remainder 0.4 amps flows
through the top branch.
Ammeter P shows 0.4 amps.

Once the current recombines and flows back to the cell, it equals 0.7 amps again.
The current through ammeter Q is 0.7 amps.

3. A buzzer is connected to a cell. Draw a circuit diagram to show how the

current through the buzzer and the potential difference across it can be
measured.

Answer

a) Note that the cell, buzzer and ammeter are all in series (in a single loop),
and the voltmeter is in parallel with the buzzer only.

4. All the bulbs in this circuit are identical. What are the readings on the
ammeter and voltmeter in this diagram?

Answer

Current reading:
The bulbs are all identical. That means the current in both branches
of the parallel circuit must be the same - 0.25 A in each. Therefore
the total current flowing out of the cell and back in to it must be 0.50
A.

140
Voltage reading:
The bottom branch is in parallel with the top branch of the circuit. According to rule
4 in the green box, the voltages must be the same as the cell, 9V for each branch.
The voltage in a series circuit is split between the two components. As the two bulbs
are identical, each gets 4.5 volts, or a p.d of 4.5 V.

Advantages of parallel circuits over series circuits

In series circuit:
 if one component fails to work or blows, then all other components will not
work.
In parallel:
 if one component fails to work, all the other components still work.
 When components are connected in parallel to a power supply, they receive
more power than when connected in series
 also in parallel components can control separately by switch

Other circuit components

Thermistor
Thermistors are used as temperature sensors, for example, in
fire alarms. In the most common type of thermistor,
the resistance decreases as the temperature increases
 at low temperatures, the resistance of a thermistor is
high and little current can flow through them
 at high temperatures, the resistance of a thermistor is
low and more current can flow through them

141
LDRs (light-dependent resistors)

LDRs (light-dependent resistors) are used to detect light

levels, for example, in automatic security lights. Their
resistance decreases as the light intensity increases

 in the dark and at low light levels, the resistance of an LDR is high and little
current can flow through it

 in bright light, the resistance of an LDR is low and more current can flow through
it

Diode

It allow the current to flow in one direction only

A diode has a very high resistance in one direction. This means that
current can only flow in the other direction.

142
This is the graph of current against potential difference for a diode

Light-emitting diodes (LEDs)

Produce light when a current flows through them in the forward

direction.

LEDs and lamps are often used for indicator lights in electrical
equipment, such as computers and television sets

Questions

1. An LED is connected in series with a 6V cell and a thermistor.

 a) Draw a circuit diagram showing the correct symbols for all

components.
 b) Explain what will happen to the brightness of the LED on a hot day, as
the temperature rises.

143
Answer

a) The circuit diagram should look like this. Note that the L.E.D.
arrow must be in the direction of current flow from positive to
negative.
b) As the temperature increases, the resistance of the thermistor
decreases. This means that the current will increase in the
circuit, and the LED will become brighter.

2. The following circuit is constructed with a fixed resistor, an LDR and

various meters:

The light level in the room slowly increases. Explain what

happens to the readings of:

 a) the ammeter
 b) voltmeter 1 (labelled V1)
 c) voltmeter 2 (labelled V2)

Answer

a) As light falls on an LDR, the resistance decreases This means the total resistance
of the two components also decreases (The total is the sum of the two resistors - the
ammeter can be ignored).
If the total resistance decreases, then the current increases as shown on the
ammeter.

b) We know that for the fixed resistor, V = I x R

If the current I round the circuit increases, and R is fixed, then V1 must increase.

144
c) The voltage in a series circuit is shared between the components.
If V1 increases, then V2 must decrease - the LDR gets a smaller share of the voltage
and has a smaller p.d. across it.

 diode have to be forward biased for current to pass

Electrical sources
1. Direct Current D.C
it is the supply which has an e.m.f. of constant polarity
and the
current is always in the same direction. Cells and
batteries provide direct current, which may change in
value but remains in the same direction.

2. Alternating Current A.C

It is the supply which has an e.m.f. of varying
magnitude and alternating polarity. This means that
the voltage is continuously changing in magnitude
and
the direction of the current is reversed continuously.

Electricity generators provide alternating current

145
 A cell is a single component power supply has a value 1.5v or 2.0v
 A battery however is a group of cell connected together to increase voltage or
power supply
 When battery is a group of cell in series the voltage increase , but the positive
terminal has to be followed by a negative terminal and vice versa so that the
current would flow in the same direction
 if the cells are connected so that like terminals face each other’s the current
opposite direction so decrease the current and may cancel current in the circuit

Switches
A switch is used to control the flow of current in a circuit. Current flows in a
circuit when the Switch is closed or on… and does not flow when the switch is
open or off.
1. Normal switch: opens and closes a circuit
2. Parallel switch: A circuit can be switched on and off using either of the two
switches.

Mains electrical plugs

1 = cable grip
2 = neutral pin and wire
3 = earth pin and wire
4 = live pin and wire
5 = fuse

146
  The live wire - this is the wire that is effectively connected to the power
station, pushing and pulling current around the circuit. If you touch the live
wire, you will receive a shock!
 The neutral wire - this is the 'return wire' completing the circuit back to the
power station.
 The earth wire - this is the third wire that is frequently missing in some
plugs, along with the third pin.
 The cable grip - this simply locks the cable in place, preventing someone
pulling on the connections, and possibly disconnecting part of the plug.
Sparks inside the plug can cause fires.
 Fuse - this is another safety feature like the earth wire,

Hazards of electricity

 Damaged insulation ‘ electric shock ‘

 Damaged plug ‘ short circuit ‘
 Damage conditions near socket ‘ short circuit ‘
 Long and tangled cables ‘ injuries

Protection

1. Fuse

It consists of a thin metal wire, mounted inside a short cylinder the fuse is designed
to melt when a specific current passes through it
When the fuse melts, it breaks the circuit and turns the appliance off preventing a
fire or other hazard. The appliance no longer works, so the fault is investigated,
fixed, and the fuse replaced

Choosing the fuse

The fuse used must be chosen carefully to match the appliance. This is because the
fuse should always be rated as just above the current needed for the appliance

147
  This is because the fuse should always be rated as just above the current
needed for the appliance.

Questions:

1. A 2kW hairdryer is connected to the mains supply of 240 V.

 a) Calculate the current used by the hairdryer when in operation.

 b) Fuses of 1 A, 5 A, 8A and 13 A are available. Which of these fuses
should be fitted to the mains plug?

Answer

a) We know that P = I x V, so

P
I=
2000
V
I=
240

I= 8.33 A

b) If the hairdryer uses 8.33 A, then an 8 A fuse will blow, as will anything rated
lower than 8 A. The next one available above 8.33 A is the 13 A fuse.

148
2. Circuit breakers

A circuit breaker is basically a more modern adaptation to the fuse. They work using
electromagnets, which open a switch if the current gets too high, and this breaks
the circuit. Many different current ratings are available.
Although the large circuit breaker box used in many homes is expensive, the
advantage is that the switches can be easily reset.

Electromagnetic induction
If a wire is moved across a magnetic field at right angles (to cut across lines of
flux), voltage is induced or generated in the wire this is called electromagnetic
induction.

149
This can be demonstrated using the following experiment
a) When the magnet is moved into the coil, the galvanometer deflects in one
direction. If the magnet is pulled away from the coil, the galvanometer deflects in
the opposite direction showing that the induced current flows in the opposite
direction.
b) If the magnet is stationary, the galvanometer
point is at zero and there’s no current induced
in the circuit.
c) If you move the magnet slowly, then small
deflection if you move it quickly, then large
deflection.
d) If you move a weak magnet, then small
deflection if you move a strong magnet, then
large deflection.

 cut off or interference between two magnetic field ( magnetic field magnet
and magnetic field of coil ) so change in magnetic field line so induced
voltage or induced current
 if it move parallel to magnetic field (no cut off) no current is induced

150
To increase induced current
1. Using coil with more turns (increases the peak value not the frequency).
2. Using a stronger magnet or a powerful electromagnet or winding the coil round
a soft-iron core so that the field is stronger (increases the peak value not the
frequency).
3. Rotating the coil faster (increases both the peak value and the frequency).

Direction of deflection
Used to determine the direction of the induced current
The direction of induced current is opposite to the change
causing it

 if the south pole is approaching the coil it should be

repelled so a south pole close to the south pole of the
magnet will be induced and vice versa

Fleming right hand rule

This rule is used to indicate the direction of current caused by induced E.M.F

151
A.C. Generator
 The a.c. generator converts kinetic energy into
electrical energy.
 The induced e.m.f. in an a.c. generator varies
with time (alternating) because the rate of
change in magnetic flux around the sides of
the coil varies as the coil rotates within the magnetic field.

To increase induced current

1- Using coil with more turns (increases the peak value not the frequency).
2- Using a stronger magnet or a powerful electromagnet or winding the coil round
a soft-iron core so that the field is stronger (increases the peak value not the
frequency).
3- Rotating the coil faster (increases both the peak value and the frequency).

The diagram shows how the varying voltage corresponds to the

different positions of the coil:
 The voltage is largest when the coil is horizontal (cutting through the field is
maximum as the coil is perpendicular to the field).
 The voltage is zero when the coil is vertical (no cutting through magnetic field
lines as the coil is parallel to the field).
 The direction of the induced current is reversed every half a rotation. This is
because the sides of the coil reverse their direction of motion across the field
every half a rotation.

152
Questions

1. Describe the conditions necessary for induction to occur.

Answer

 Movement
 Of a wire / coil / conductor..
 Through a magnetic field /cutting through field lines / perpendicular to a
magnetic field.

2. An a.c. generator consists of a rotating coil in a magnetic field as shown in

figure

 a) State one way the output voltage from the generator can be
increased.

153
  b) Explain why an alternating voltage is produced.
 c) Explain why there is a point in the rotation where no voltage is
produced.

Answer

a) To make the voltage higher, you can

either increase the strength of the magnets /
magnetic field, rotate the coil faster, or use more
turns on the coil.

b) An a.c. voltage is produced because any one

side of the coil moves up then down through the field as it rotates, making the
direction of the induced voltage change constantly.

c) At one point of the rotation, the sides of the coil are moving parallel to the field, so
no field lines are cut. Therefore, no voltage is induced

Magnetic Effect of a Current (electromagnetism)

When a current flows through a wire a magnetic field is created around the wire.
This is called Electromagnetism.

To make a powerful electromagnet, you need three

things

 A coil, like the solenoid, that will produce a

concentrated field inside.
 A current flowing through the coil.
 A soft magnetic material core inside the coil that
will be magnetized when the current is turned on, and quickly lose its
magnetism when switched off.

154
To make a powerful electromagnet, you need a large number of turns in the coil, a
high current, and a highly magnetic material like a soft iron core, notice the 3 'C's
Remember Coil, Current, Core.

Relay switch
allow a small current to switch on or off a large current
 when small current , usually supplied with a low voltage passes through the coil
( electromagnet ) it is magnetized and attracts the spring metal to close the
second circuit which has separate power supply (high current)

Solenoid
Is basically a long coil of wire When a current passes through it, a strong magnetic
field is produced in the center of the coil as shown in figure Outside the coil, the
field is much weaker.

155
Properties of the magnetic field around a solenoid
1. The magnetic field around a solenoid is the same as that around a bar magnet.
One end of the coil is a north pole and the other is a south pole.
2. The magnetic field inside a solenoid consists of close, equally spaced and parallel
flux lines “it is a strong uniform field”.
3. If the direction of the current flowing through the solenoid is reversed, so too are
the positions of the poles.

The strength of the magnetic field around a solenoid can

be increased by
1. Increasing the current flowing through the solenoid.
2. Increasing the number of turns on the solenoid – this does not mean making the
coil longer but packing more turns into the same space to concentrate the field.
3. Wrapping the solenoid around a magnetically soft core such as iron. Iron is easily
magnetized when current flows and is easily demagnetized when no current flows
in the solenoid

 reversing the direction of the current reverse the direction of the magnetic
field

The right hand grip rule

Hold out your right hand with your thumbs tucked in and your
thumb pointing upwards:

 the thumb is equal to the direction of current

 the fingers are equal to the magnetic field direction

156
DC electric motor
Motor consists of
1. a rectangular coil
2. N-S poles of a permanent magnet,
3. split ring commutators
4. Carbon brushes.
 As current passing to coil by two carbon brushes magnetic field is created
around the coil
 Repulsion Force between magnetic field of coil and magnetic field of permanent
magnet , the coil turn 180 0 half turn
 split ring commutator reverse direction of current every half turn , to reverse
magnetic field of coil to complete rotation of coil ( complete turn )

To increase the rate of motor (the speed of rotation)

1. Increase the number of turns or loops of wire
2. Increase the strength of the magnetic field (use a stronger magnet).
3. Increase the current flowing through the loop of wire.

 If the direction of the current, or the poles of the magnet are reversed,
rotation will proceed in the Opposite direction.

Loudspeaker
The interact of the magnetic field generated by the coil and magnetic field of
permanent magnet apply force on the cone so that it moves in
certain frequency which produce sound

157
Questions

1. A loudspeaker is connected to an a.c. electrical supply and produces a sound

wave. Suggest one way the speaker or supply could be modified or changed to
produce:

 a) A louder sound.
 b) A higher frequency sound.

Answer

a) To make the sound louder, you can increase the current (or voltage) from the
supply, increase the strength of the magnet / field used in the speaker, or use more
turns on the coil.

b) To produce a higher frequency sound, the frequency of the a.c. supply must also
be increase

2. A simple motor rotates due to the 'motor effect' forces acting on the coil.
Suggest two ways of increasing the force on the coil, and hence the speed of
rotation.

Answer

 Increase the current (or supply voltage).

 Increase the magnetic field strength produced by the magnets.
 Increase the length of the wire in the field, by having more turns on the coil.

158
Fleming's left-hand rule
 The Thumb indicates the thrust (a force) on the current carrying
conductor.
 The First finger indicates the magnetic field (remember field lines go from
north to south).
 The second finger indicates the current.
 The magnetic field is always directed from north to south.

 Note that all three fingers in the left-hand rule are perpendicular to each other.
If there is a situation where the current is parallel to the magnetic field, then
there is no force.

Questions

1. A metal wire has a current flowing through it, and

is placed between two permanent magnets as shown
here:

 a) Use the left-hand rule to predict the force on the wire. Draw an arrow
on the diagram to show the direction of this force. Label the arrow 'F'.

159
  b) Describe a method of increasing the size of the force F without
replacing the magnets.

Answer

a) Your first finger on your left hand should point right, from
N to S. Your second finger should point into the 'page'. This
leaves your thumb pointing downwards. Your thumb
indicates the motion and hence the force. Draw an arrow downwards as shown here

b) You can increase the force by increasing the current. Alternatively, wrapping the
wire into a loop or coil with only one edge inside the field will effectively increase
the length of the wire. (Note that the magnets cannot be replaced in the question, so
you cannot increase the field strength).

Summary

Transformers
A transformer is a device that can change the potential difference or voltage of an
alternating current AC

 a step-up transformer increases the voltage

In a step-up transformer,( Vs > Vp ) &( Ns > Np )

160
 a step-down transformer reduces the voltage

In a step-Down transformer ( Vs < Vp ) & ( Ns < Np )

Structure of a transformer
A basic transformer is made from two coils of wire, a primary coil from the
alternating current (ac) input and a secondary coil leading to the ac output. The
coils are not electrically connected. Instead, they are wound around an iron core.
This is easily magnetized and can carry magnetic fields from the primary coil to the
secondary coil

 The alternating voltage causes an alternating magnetic field to be set up

inside the iron core. This in turn induces an alternating voltage in a
secondary coil

161
 input (primary) voltage [V] number of primary turns
=
output (secondary) voltage [V] number of secondary turns

Vp Np
=
Vs Ns

Questions

1. A phone charger uses a transformer with 5 000 turns on the primary coil
and 250 turns on the secondary. It is plugged into the mains supply with an
input voltage of 240 V.

 a) Explain if this is a step-up or step-down transformer.

 b) Calculate the output voltage of the transformer.

Answer

a) There are fewer turns on the secondary coil than the primary, so this is a step-
down transformer.

b)
Vin np
240 5000
= =
Vout ns Vout 250

240 x 250 Vout

=
5000 1

So Vout = 12 V

2. A very high voltage is required for 'spark' plugs that ignite the petrol in any
car engine. The transformer used to do this has an input voltage of 12 V and an
output voltage of 4800 V. The primary coil has only 10 turns.

162
Calculate the number of secondary turns required to produce 4800 V.

Answer

V n 12 10
p p =
= 4800 ns
Vs ns

ns 4800 x 10
=
1 12

So ns = 4000

Transformers and efficiency

The formula for electrical power is P = I x V as We also know that energy cannot be
created Assuming the transformer is 100% efficient and no power is lost, then
the output power must match the input power.

Input power = output power

Vp x Ip = Vs x Is

Questions

3. A school power supply is used to run a heating element for an experiment.

The heating element runs on 12 V, and has a power output of 60 W.

The transformer used in the power supply has 240 V input and 800 turns on
the primary coil.

Calculate:

 a) The number of turns on the secondary coil of the transformer.

 b) The current output to the heating element.
 c) The current input to the transformer.

163
Answer

Vp np
240 800
= =
Vs ns 12 ns

and rearranging this gives

12 x 800
ns =
240

So ns= 40

b) P = I x V,
so 60 = I x 12 Therefore I = 5 A

c) Using the second transformer equation Vp x Ip = Vs x Is gives:

Vp x Ip = Vs x Is
240 x Ip = 12 x 5 (from part b)

Therefore:

12 x 5
Ip =
240

Ip = 0.25 A

The national Grid system

 It is a network of wires and cables that carries electrical energy from power
stations to consumers such as factories and homes. To transfer the energy from
the power station to your home we use A high voltage and a low current.
 Because if the current flowing through the wire is kept to a minimum, the heat
losses are also reduced This is done with transformers at each end of the Grid

164
 system to step-up the voltage and keep the current very low. This is the main
reason for using a.c. in the Grid (transformers do not work with d.c.).
 The step down transformer at the end of the transmission line reduces the
voltage back to safe usable levels at the consumer end

Questions

4. The diagram below shows the main stages in a local power distribution
system:

a) State the name of the type of transformer used at X and Y.

b) Explain why these transformers are required.

Answer

a) X is a step-up transformer, Y is a step-down transformer.

b) A step-up transformer increases the voltage and decreases the current. A lower
current leads to less power loss in the cables. (The high voltage and low current
makes the transmission more efficient).

165
The step-down transformer is required to reduce this high voltage back down to
safe levels for domestic use.

166
 5-Atomic Physics
Atom
All atoms are made of three sub-atomic particles

 Protons - these have a positive charge (of +1) they are

found in the nucleus.
 Neutrons - these have no charge (are neutral) they are also
found in the nucleus.
 Electrons - these have a negative charge (of -1), they orbit
the nucleus.

Subatomic particle Mass Charge Location

Proton 1 +1 Nucleus
Neutron 1 Neutral Nucleus
Electron 1/2000 -1 Outer shell

 You will need to learn the terms atomic

(or proton) number, mass (or nucleon)
number, and what they mean:
 The bottom number is always
the atomic number, and is the number
of protons in the nucleus.
 The top number is always the mass number, and is equal to the mass of the
nucleus. It equals the total number of particles in the nucleus, known as
nucleons.

167
Example
an atom of oxygen is represented by O816
 is the chemical symbol for oxygen
 The atomic number is 8 (the nucleus contains 8 protons )
 The mass number is 16 (so it must have 8 neutrons).
Questions
23
1. The element sodium (Na) is written in notation as: Na
11

State the number of protons and neutrons in this atom of sodium.

Answer

The bottom number represents the proton number, so there are 11 protons.
The top number of 23 gives the total number of protons and neutrons, so there are
23 - 11 = 12 neutrons.

2. Lead is a metal with the symbol Pb. A common atom of lead has 82 protons
and 125 neutrons. Using standard notation (as shown in question 1), give the
notation for this atom of lead.

Answer

If the atom has 82 protons and 125 neutrons, the total mass is 82 + 125 = 207.
Therefore the notation will be:
207
Pb
82

168
Isotopes
Isotopes have the same number of protons, but different numbers of neutrons.

Questions

3. The list below shows the notation for some atoms found in a sample of sea
water. It includes 2 isotopes:

1 4 5 2 9 9
H He Li H B Be
1 2 3 1 5 4

 a) Define the term 'isotopes'.

 b) Identify the two isotopes in the list.

Answer

a) isotopes have the same number of protons but different numbers of neutrons.

b) We are looking for 2 atoms with the same proton number (the bottom number)
and hence the same symbol.

1 2
The two isotopes are: H and H
1 1

169
Alpha scattering experiment
In this experiment, a beam of alpha particles was aimed at a thin sheet of gold foil.
The experiment must be carried out in a vacuum tube to prevent alpha particles
from being stopped by air particles.

Results
1. Most of alpha particles pass straight
through the gold foil, because they do
not pass close to the nucleus

2. Some particles suffer some deflection.

The closer the particles are to the nucleus,
the more they are deflected.

3. Few particles closely approach a gold nucleus so they deflect backwards

Conclusions
 From 1, the volume of the nucleus is small as compared to the volume of the
atom; the atom is mostly empty space.
 From 2, the atom has a positively charged nucleus.
 From 3, the atom has a dense, relatively heavy nucleus; the nucleus carries
most of the atom’s mass.

Radioactivity

1) Stability & radioactivity

Some elements have atoms with unstable nuclei. These unstable nuclei emit high-
energy particles and rays called radiations.

170
Radioactive decay
Is the spontaneous random emission of alpha (α), beta (β) particles or gamma (γ)
rays from the nuclei of unstable atoms to become more stable

Random
Means we cannot predict which particular nucleus will decay next, all nuclei have a
constant probability of decay.

Spontaneous
Means that the decay process is unaffected by environmental conditions such as
temperature, pressure,

2) Types of nuclear radiation

Nuclear radiations are sometimes called ionizing radiations. This is because these
radiations interact with neutral atoms of air, which makes atoms gain or lose
electrons, forming ions.

The three types are

 Alpha (α) particle
 Beta (β) particles
 Gamma (γ) radiation

a) Alpha particles (α)

It is identical to the nucleus of a helium atom (a helium atom without its orbiting
electrons, it’s not a helium atom). Alpha particles make frequent collisions with gas
molecules along their paths, causing intense ionization. Accordingly, they have
strong ionizing
Here’s its nuclear equation

171
Note that
 The mass number reduced by 4 and the atomic number reduced by 2
For example

b) Beta particles (β)

A beta particle is a very fast moving electron that is ejected by a decaying nucleus,
This means that the atomic number increases by 1, while the mass number stays
the same. Beta particles are smaller & carry less charge so they interact less
frequently with matter in their paths. This is why they have weak ionizing
Here’s its nuclear equation

For example

Note that
 the mass number stay the same while the atomic number increase by 1

C) Gamma rays (γ)

Gamma rays is electromagnetic radiation emitted from the nucleus of an unstable
atom so they have a very weak ionizing

Neutron decay
Some isotopes lose neutrons when they decay , A neutron has a mass of 1 and no
1
charge, it is therefore written as:
n
0

172
Again, the decay of an isotope is then quite easy to work out. For example, if
Beryllium-13 decays by emitting a neutron:

13 1 12
Be → n + Be
4 0 4

Penetrating power
The penetrating power of alpha rays, beta rays, and gamma rays varies greatly.
Alpha particles can be blocked by a few pieces of paper. Beta particles pass through
paper but are stopped by aluminum foil. Gamma rays are the most difficult to stop
and require concrete, lead, or other heavy shielding to block them

173
Questions

1. A student is researching the nature of alpha, beta and gamma radiation.

Which of these three:

 a) Has the largest mass?

 b) Has no charge?
 c) Will only pass a few centimeters through air?

Answer

a) Alpha particles have the largest mass.

b) Gamma radiation has no charge.

c) Alpha can only pass through a few cm of air.

2. A radioactive isotope is thought to be a beta emitter, with no alpha or

gamma being emitted. Describe an experiment to prove this result.

Answer

You need a Geiger counter to use as a detector.

First, place paper / tissue in front of the source. If alpha radiation is present, the
detected count rate will drop significantly. If there is no drop, the radiation is beta or
gamma.

Second, place a thin aluminum sheet or two in front of the source. If the count rate
drops, the source is a beta emitter. Gamma rays will not be significantly affected by
the aluminum barrier.

174
3. An alpha particle is given the letter α

 a) State the mass number and atomic number 239 __ __

of an alpha particle. Pu → U + α
 b) Complete the missing numbers in the alpha 94 __ __

decay equation below, for the isotope

plutonium 239:

Answer

a) Alpha particles have a mass of 4 and an atomic number of 2.

b) The missing numbers are shown here

239 235 4
Pu → U + α
94 92 2

4. During beta decay, the mass of the nucleus remains constant, whilst the
atomic number increases by 1.

 a) Explain the change in the nucleus that causes

90 __ __
this result.
Sr → β + Y
 b) Stronium-90 (Sr) is a radioactive isotope
38 __ __
('radioisotope') that decays by emitting a beta
particle. The resulting nucleus is an isotope of yttrium (Y). Complete the
missing numbers in the beta decay equation shown below:

175
Answer

a) During beta decay, a neutron changes into a proton and an electron, causing an
increase in the nuclear proton number of +1 but no change in mass. (The electron is
ejected from the nucleus).

b) The missing numbers - shown i

90 0 90
Sr → β + Y
38 -1 39

a) Deflection in electric fields

Electric field lines represent the direction of an electric field which is from the
positive plate to the negative plate. The positively charged alpha particles are
attracted to the negative plate while the negatively charged beta particles are
attracted to the positive plate.

176
b) Deflection in magnetic fields
Alpha & beta particles are deflected in directions given by Fleming’s left hand rule.
Keep in mind that negative charges traveling to the right counts as a conventional
current to the left

Radiation and half-life

The half-life time of a radioactive sample is the time taken for half the nuclei present
in this sample to decay
(The time taken for the activity of a radioactive sample to decrease to its half)
The half-life is unaffected by temperature or pressure but each radioactive
element has its own definite half-life.

The decay curve

The activity of a sample is the average number of decaying
atoms per unit time. If the activity of a sample is measured at
different times, a decay curve against time can be plotted.
The decay curve of a sample starting with an activity of 200
radiations per hour is shown.
The curve shows that the activity falls by the same fraction in
successive equal intervals of time.
The half-life time of this sample is 1 hr.

177
Questions

1. Radioactive radon gas can be found in caves in high concentrations. The

isotope has a half-life of 3.8 days.

 a) Explain the term 'half-life'.

 b) If the total mass of radon gas found in a cave is found to be 4 grams,
calculate the quantity that should remain after 7.6 days. (Assume no
more radon gas enters the cave).

Answer

a) The half-life of a substance is defined as the time it takes for...

 half the nuclei to decay, or

 the count rate / activity to fall to half the original value

b) After 3.8 days, the mass will have halved, from 4 g to 2 g.

After 7.6 days (a further 3.8 days), it will have halved again down to 1 gram.

2. An isotope used in engineering has a half-life of approximately 10 years and

an activity of 800 kBq.

If the dangerous isotope is buried for 30 years, what will be the activity after
this period?

Answer

For this we will use a table of results to show our working out, halving the activity
each half-life:

number of half-lifes 0 1 2 3

Time (yrs) 0 10 20 30

Activity (kBq) 800 400 200 100

178
From this table we can see that after 30 years, the activity is 100 kBq.

3. A medical sample of technetium-99m has an activity of 20 000 Bq. It has a

half-life of 6.0 hours. What will the activity of the sample be after 24 hours?

Answer

Using a table again gives these results

number of half-lifes 0 1 2 3 4

Time (hours) 0 6 12 18 24

Activity (Bq) 20 000 10 000 5 000 2 500 1 250

From the table we can see that after 24 hrs, the activity is 1250 Bq

Detection of Radiation By
1-photographic film
Become blacked when subject to radioactivity, the darker the film the greater the
radiation dose

2-Geiger-Muller (GM) tube

The main detector used now which is connected to a count rate meter giving reading
in counts per unit time (minute or second)

179
Background radiation
A GM tube will record some count rate even in the absence of a source. This count
rate is due to the ionizing radiation which is always present from the surroundings.
It is called background radiation and should be subtracted from the counts
recorded when a source is present to give the true count rate due to the source.

Sources of background radiation

1. Radon gases in the air
2. Some rocks in the Earth’s crust or in building material
3. Radioisotopes used in certain medical procedures.
4. Cosmic rays from outer space.
5. Emissions from nuclear power stations.

Used of radioactivity
1. Gamma rays are used to kill bacteria specially in sterilizing medical equipment
and in preserving food.
2. Alpha particles are used in smoke alarm for smoke detection. Alpha particles
have high ionization effect and therefore they ionize the air molecules in between
the two metal plates allowing the current to pass through. When smoke enters
between the plates, some of the alpha particles are absorbed causing less ionization
to take place. This means a smaller than normal current flows so the alarm switches
on.
3. Beta particles are used to monitor the thickness of the paper or metal sheets in
manufacturing factory. Some of the radioactivity is absorbed by the foil and some
passes through to the detector. The thicker the foil, the fewer radio activities passes
through it to the detector. The amount of radioactivity arriving at the detector is
monitored by the computer. The thickness of the foil is controlled by the gap
between the rollers.
4. Carbon-14 is used to find the age of living organism or plants. This method is
called radioactive carbon dating. There's a small amount of radioactive carbon-14 in

180
all living organisms. When they die no new carbon 14 is taken in by the dead
organism. The carbon-14 it contained at the time of death decays over a long period
of time. By measuring the amount of carbon-14 left in dead organic material the
approximate time since it died can be worked out
5. Uranium -238 which eventually decays into lead is used to find the age of
igneous rock
6. In radiotherapy the high doses of gamma radiation are used to kill the cancer
cells
7. Find leaks or blockages in underground pipes.

Safety precautions
1. Always use the radioactive symbol where there is a radioactive substance stored
2. Always be stored in a lead-lined container;
3. Be handled only with tongs
4. Never be pointed at anyone
5. Never be put in pockets
6. Only checked by looking at them in a mirror.

181
 6- SPACE PHYSICS
The Earth
 The Earth is a planet, and it orbits the Sun.
 The Earth takes just over 365 days to complete one orbit.
 The Earth also spins on its axis and it takes about 24 hours to
rotate once.
 The Earth's axis (an imaginary line through the Earth from the North pole to
the South pole) is tilted at an angle of about 23.5 degrees
 The Earth is about 150 million kilometers from the Sun, and the Moon is
about 384 thousand kilometers from the Earth

Day and night

 Because the Earth spins on its axis, sometimes you are
facing the Sun and sometimes you are facing away from the
Sun. The Sun only shines on the half of the Earth that is
facing it.
 When you are facing the Sun, you are experiencing day-
time.
 When you face away from the Sun, you are experiencing
night-time.
 The Earth spins towards the East. That is why the Sun appears
to rise in the East and set in the West. At midday in the Northern
Hemisphere it appears to be in the South.
the earth that is rotating not the sun is moving

182
The Seasons
 The Earth moves round the Sun once in approximately 365 days , We
experience different seasons due to the amount of direct sunlight we
receive

 In December the Northern Hemisphere is tilted away from the Sun and in
June it is tilted towards the Sun. In June the Northern Hemisphere receives
more direct sunlight and so it is summer. At the same time, the Southern
Hemisphere is tilted away from the Sun and it is winter.

183
  At the equator the seasons do not vary as much because there is direct
sunlight all year round.
 At the poles during winter there are days when the Sun never rises, and days
during summer when the Sun never sets.

 The maximum height of the Sun in the sky varies according to the seasons.
In summer it is high and casts short shadows. In winter it is low and casts
long shadows. The variation is more pronounced nearer the poles. The
diagram below shows how shadows vary in the Northern Hemisphere.

Phases of moon

 It takes about a month for the Moon to orbit the Earth. It orbits with the
same side of the Moon facing the Earth all the time.
 We can only see the Moon because it is illuminated by (reflects light from
the Sun), which shines on it. It does not produce its own light.

 As the Moon orbits the Earth it reflects different amounts of light towards
Earth. When the Moon is between the Sun and the Earth it does not reflect
any light towards the Earth. We call this a New Moon. As it continues to orbit
we see more and more of the Moon, and we say it is waxing, towards a Full
Moon, and then it wanes again

184
Orbital speed

This formula to give us the speed around a circular orbit:

2 x π x orbital radius
orbital speed =
time period

2xπxr
v=
T

 If a question gives the radius in kilometers (km) and the time in hours (h), then
the speed will be in units of km/h.

185
Questions

1. The moon orbits the Earth in approximately 708 hours, with a radius of
orbit of 385 000 km. Using the formula given above, calculate the orbital
velocity of the Moon.

Answer
2 x π x 385 000
2xπxr v=
v= 708
T

Therefore v = 3 420 km/h (to 3 sig figs) or 0.949 km/s.

2. The Hubble Space Telescope (HST) orbits the earth at a speed of 7.6 km/s
and has an orbital time period of 5700 seconds.

 a) Using the formula given above, calculate the radius of the HST's orbit
from the center of the Earth.
 b) The Earth has a radius of 6400 km. Calculate the distance from the
HST to the Earth's surface.

Answer

a) Both time period and speed include seconds, so we can substitute the numbers
directly into the formula
2xπxr
7.6 =
2xπxr
5700
v=
T

186
 7.6 x 5700
r=
2xπ

Therefore r = 6900 km (to 3 sig figs) .

b) The Earth's radius is 6400 km, so the HST's height above the Earth's surface is
6900 - 6400;
so the distance = 500 km

Space

1. The solar system: Our solar system consists of the Sun at the center, with 8
planets in orbit around it. There are also comets orbiting the Sun, and moons
orbiting the planets. There are similar solar systems around other stars.

 To remember the planets in order “ My Very Educated Mother Just Served Us

Noodles”

2. Galaxies: There are billions of stars in most galaxies. Our Sun is in a huge
galaxy called the Milky Way. It has about 100 billion stars in it. Many probably have
planets. The galaxy nearest to us is called the Andromeda galaxy both of these
galaxies are spiral galaxies, with the outer stars orbiting around a very heavy central
mass of stars.

187
3. The universe: The observable universe is believed to consist of billions of
galaxies

Gravity

The motion of galaxies, stars and planets are all ruled by the force of gravity. This
force between any 2 objects depends on the masses of the objects and also the
distance between them. The pull of gravity makes:

 moons orbit planets

 artificial satellites (like the international space station) orbit the Earth
 the Planets orbit the Sun
 Comets orbit the Sun.

Orbits

Moons generally travel around planets in a circular orbit. This means that they keep
approximately the same distance from the planet at all times. This is also true of
planets as they orbit the Sun. The Earth stays at approximately the same distance
from the Sun all year as it travels around in its orbit.

However, comets are very different. The distance from the Sun and the speed of a
comet varies dramatically, as shown in figure

188
The correct mathematical name for this orbit shape is an ellipse. All comets have an
elliptical orbit, and as they approach the Sun, the pull of gravity makes them travel
faster and faster. The comet is fastest at its closest approach to the Sun

 as the distance from the sun increase the time to complete an orbit for a planet
increase for planet increase because
-the orbital distance increase
-the speed of a planet in its orbit decrease as gravitational field strength
decrease
 in elliptical orbit the distance from the sun change and gravitational potential
energy change because of the conservation of energy
Total energy = Ek + Ep
when the planet is closer to the sun its Ep is smaller and its Ek is greater and
it move faster

Asteroids

 Are made up of metal and rock and are much smaller than planets usually with
irregular shapes
 most of them are found between the planets mars and Jupiter the dwarf planet
ceres is found there

Comets

 comets are lumps of ice and dust which orbit around the sun , many comets
have elliptical orbit

Satellites
A satellite is anything that orbits a celestial body (star, planet, moon ). Both natural
and artificial satellites exist.

189
 Natural satellites
The Moon is the Earth’s natural satellite. Scientists believe that it was formed when
a Mars-sized planet collided with the early Earth, throwing some of the crust into
orbit. However the Moon was formed, it is locked into the Earth’s gravitation field
and circles our planet once every 27.5 days. Many other moons are the natural
satellites for other planets in our solar system and beyond.

Artificial satellites
These have been placed into orbit by man. Among other jobs, artificial satellites
orbiting the Earth are used for:

 telecommunications (transmitting information between distant parts of the

Earth)

 satellite navigation systems

 spying on other countries

 weather forecasts

 Communications satellites occupy a geostationary orbit. They are in orbit

above the equator at just the right distance so that it takes them one day to
complete an orbit. As a result, they always appear in the same position when
seen from the ground. This is why satellite television dishes can be bolted
into position and do not need to move.

Questions

3. A rocket launched from the Earth's surface has to escape from the Earth's
gravitational pull.
Explain why it might be easier to launch a rocket from the surface of Mars.

190
Answer

Mars has a lower mass than the Earth, and therefore lower gravitational field
strength (g). This means it takes less energy to launch the rocket into space.

4. Explain the difference between the orbit of a comet and of a planet.

Answer

Both comets and planets orbit the Sun. However, planets have an
approximately circular orbit, whereas comets have a highly elliptical orbit

Stars
Stars have many different colors, ranging here from red and orange, to white and
blue. This is because the stars all have a different temperature at the surface.

The color of the star indicates the temperature. Red stars are not as hot as orange
stars. Then comes yellow/white, white, and finally blue stars that are extremely hot
at the surface.

191
The evolution of stars

Nebula

All stars begin from a humble cloud of gas and dust, called a nebula. If the mass of a
region of the nebula is large enough, gravity begins to pull the nebula together and
compress it form a hot ball of gas known as protostar

Main sequence stars

The gas has been compressed so much that the temperature reaches millions of
degrees Celsius, enough for a fusion reaction to begin. A star is born! The fusion
reaction lasts for a long time - billions of years for a star like the Sun

Red giant

When stars begin to run out of hydrogen, more complicated fusion reactions can
start. The star begins to swell outwards and cool a little at the surface,
producing red giant stars.

White dwarf

When the last of the fusion reactions stops, the star shrinks. As it does this, the
compressed gases heat up making the star white hot at the surface, but very small

192
Very large stars (Supergiant)

Stars with a mass much higher than the sun will be extremely bright and will
convert hydrogen at a vast rate through fusion reactions when the hydrogen runs
out, they also swell up to make red supergiant stars

Supernova

Once a red supergiant runs out of fuel to sustain the complicated fusion reactions
that occur, the star collapses very rapidly. As it rushes inwards, The star explodes in
a flash releasing so much energy it can out-shine an entire galaxy This explosion is
called a supernova.

Neutron star

The remaining core collapses into a tiny, extremely dense core made of neutrons,
called a neutron star.

Black hole

If the core remnant has a huge mass, it collapses inwards to a point. Nothing can
stop the collapse. This is where things get very weird, as the star is still there, with a
high mass and strong gravity, but it is effectively a point in space. This is called
a black hole.

193
Questions

1. The Sun is currently a main sequence star, in the middle of its evolutionary
path.
Describe the next two stages in the evolution of stars like the Sun.

Answer

 The sun will eventually increase in size, and cool to become a red giant.
 After that, it will shrink to a much smaller size, and heat up to become
a white dwarf.

2. Very large main sequence stars will eventually run out of hydrogen in the
star's core. Describe the next stages in a life cycle of a star.

Answer

A very large main sequence star will

 Eventually increase in size to become a red supergiant.

 It then explodes. This is called a supernova.
 The star remnant then collapses to form a neutron star, or - if it is a huge
remnant - to form a black hole.

3. Explain what is meant by a nebula.

Answer

A nebula is a large cloud containing gases (like hydrogen and helium) / dust.

194
The Big Bang theory

This theory states that the Universe started from extremely hot single point and
began expanding and cooling. In an enormous release of energy (the Big Bang) all
matter was created and moved outward from this point. Eventually the matter
formed dust clouds, stars and the galaxies we see today. However, these galaxies are
still moving outwards - the universe is still expanding.

 Key pieces of evidence led to this being the main theory that is supported today.
The two pieces of evidence are the red-shift of distant galaxies, and CMB
radiation

1-Red-shift

When very distant galaxies were first observed, astrophysicists noticed that
frequencies produced by the hydrogen in stars had been shifted to longer
wavelengths.

 Wavelength red end of the spectrum. This effect is called red shift.

Remember Doppler Effect A source of waves moving away from us produces a

shift in the wavelength of light towards longer wavelengths. That is what is being
observed here - distant galaxies are moving away from us at very high speeds. In
fact, the further the distance to the galaxy, the faster the recession
velocity (recession means 'moving away'). This higher velocity leads to a higher red
shift.

2-cosmic microwave background radiation

If the big bang happened, releasing a vast quantity of matter and radiation, then the
radiation remaining should now be enormously red-shifted into the microwave
region of the EM spectrum. Penzias and Wilson had discovered what we now call

195
the cosmic microwave background radiation (CMB radiation), exactly as
predicted by the Big Bang theory.

The CMB radiation, along with the red shift of distant galaxies has provided
astrophysics with enough evidence for them to be reasonably certain that the Big
Bang theory is correct. The universe did have a starting point

Questions

3. In 1964, CMB radiation was discovered.

 a) State what is meant by CMB radiation.

 b) Explain why CMB radiation supports the Big Bang theory for the
origins of the universe.

Answer

a) CMB radiation is cosmic (from space) microwave background (all around us)
radiation.

b) This radiation is predicted from the big bang theory: Any radiation produced in
the big bang should now be red-shifted to microwave radiation, but should be
observable in all directions.

The Hubble constant

 Hubble's Law states that a galaxy's recessional

velocity (its velocity away from us) is directly
proportional to the galaxy's distance from
Earth.

 A graph of recessional velocity against distance

from Earth is a straight line passing through the
origin.

196
  This graph shows that galaxies that are further away from Earth are
moving away even faster than those closer to Earth. The Hubble constant is
equal to the gradient of the graph

 the time it has taken for the galaxies to reach their current is given by

t= =

 so you can take as an estimate for the age of the universe

This is further evidence that all matter in the universe came from hot dense
point

Questions

A galaxy is found to be moving away with a speed of 2.1 × 107 m s-1. The galaxy
is at a distance of 9.5 × 1024 m from Earth Assuming the speed has remained
constant, what is the age of the universe in years?
Answer
v = H0d

Rearrange for the Hubble constant H0, and calculate

Write the equation for the age of the universe T0, and calculate

197
Convert from seconds into years

Therefore, the age of the universe is estimated to be about 14.3 billion years

198
199
200
201
202
203
204
205
206
207
208
209
210
211
212
213