Ijmet 08 11 014

International Journal of Mechanical Engineering and Technology (IJMET)
Volume 8, Issue 11, November 2017, pp. 121–128, Article ID: IJMET_08_11_014
Available online at http:// http://iaeme.com/Home/issue/IJMET?Volume=8&Issue=11
ISSN Print: 0976-6340 and ISSN Online: 0976-6359
© IAEME Publication Scopus Indexed
DETERMINATION OF FLOW
CHARACTERISTICS IN FIRE-TUBE BOILER
USING NUMERICAL SIMULATION
Somya Ranjan Gochhayat, Kunjan Modi, Amrutkar Pranit Sanjay, Satwik
Talegaonkar, Saumen Dutta, Shivam Sanjay Singh
School of Mechanical Engineering, VIT University, Vellore, India
Premkartikkumar SR*
Automotive Research Centre, School of Mechanical Engineering,
VIT University, Vellore, India
ABSTRACT
This paper provides the thermal analysis of fire-tube boilers used in thermal power
plants. For simulation purpose, a small-scale prototype of the original fire-tube boiler
is designed using Solid Works. The numerical simulation of the designed model is
carried out in ANSYS Fluent. The initial section of the paper represents the pressure
and temperature variations along the length of the boiler for different water velocities
(25 m/s, 30 m/s, 35 m/s and 40 m/s). The later section deals by changing the boiler
casing material between steel, brass and stainless steel to study the pressure and
temperature variations at constant water velocity of 30 m/s. Based on the results, the
best boiler shell material among these three has been identified. The results have been
provided in the form of pressure and temperature contours as obtained from the CFD
analysis.
Key words: Fire Tube Boiler, Numerical Analysis, ANSYS Fluent, CFD Analysis,
Negative Heat Flux, Pressure-Velocity Variation.
Cite this Article: Somya Ranjan Gochhayat, Kunjan Modi, Amrutkar Pranit Sanjay,
Satwik Talegaonkar, Saumen Dutta, Shivam Sanjay Singh and Premkartikkumar SR,
Determination of Flow Characteristics In Fire-Tube Boiler Using Numerical
Simulation, International Journal of Mechanical Engineering and Technology 8(11),
2017, pp. 121–128.
http://iaeme.com/Home/issue/IJMET?Volume=8&Issue=11
http://iaeme.com/Home/journal/IJMET 121 editor@iaeme.com

Somya Ranjan Gochhayat, Kunjan Modi, Amrutkar Pranit Sanjay, Satwik Talegaonkar, Saumen
Dutta, Shivam Sanjay Singh and Premkartikkumar SR
1. INTRODUCTION
Boilers are pressure vessels which are used for heating water or generating steam for the heating
facility in industries and to generate electricity through steam turbines. A boiler is an enclosed
vessel which is used to provide heat for the combustion of the fuel in the thermal power plant
[1]. In a fire tube the hot gases or flue gases pass inside the boiler tubes and the water is
transferred outside in the shell. Water gets converted into the high temperature by the heat
transfer from the gases to water [2]. If the boiler is subjected to the high temperature and high
pressure conditions then the walls of boiler are subjected to the high stresses [3]. The main
components of a boiler are fabricated by the high-temperature alloys such as steel, cast iron,
stainless steel etc. The failure in the boiler generally affects the output of the overall power
plant. Identifying the correct failure reason often helps to ensure integrity of the component.
There are many reasons due to which boiler failure occurs such as pitting, stress corrosion
cracking, stress rupture, creep, erosion and thermal fatigue [4].
In the Pulverized coal-fired boiler, the flue gases temperature can reach up to the 1200˚C
and it contains fly ash that induces the erosion [5]. In present, the boilers have to completely
isolated from the external environment for the proper functioning. So, methodologies based in
the computational simulations have been used to analyze effect of velocity on boiler function.
Now a days, the computational analysis is used instead of prototype. It is the advantageous tool
for analyzing the fluid flow and heat transfer problems.
2. FORMULATION AND SOLUTION METHODOLOGY

The small-scale prototype of the fire-tube boiler was designed using Solid Works. The
individual parts, i.e. the boiler shell, water flow domain, fire tubes and exhaust flow domain,
were designed individually and then assembled to get the final model. The assembly of the fire-
tube boiler was saved as .STEP file to import it in ANSYS Fluent. The boiler consisted of two
fire tubes through which hot exhaust gases would flow. The isometric view of the final model
is shown in Fig. 1 along with the geometrical specifications in Table 1.
Figure 1 Isometric view of the 3D fire-tube boiler

Determination of Flow Characteristics In Fire-Tube Boiler Using Numerical Simulation
Table 1 Geometrical Specifications of 3D fire-tube model

Sr. No. Feature Dimension (mm)
1 Length of boiler 550
2 Diameter of boiler casing (inner/outer) 300/350
3 Diameter of fire tube (inner/outer) 35/50
The assembly was imported to ANSYS Fluent and meshing was carried out. The mesh type
was set to Automatic, hence we got triangular cells. The cell count of the mesh was 1, 36, 518.
Named selections were created for various part surface. The meshed model is shown in Fig. 2.
Figure 2 Meshed fire-tube boiler model

The simulation has been performed using ANSYS Fluent 17.2, 3D double precision,
pressure based version and realizable k −  has been solved.
The required materials were selected from the fluent database. The inlets and outlets for the
fire tube and boiler were selected as velocity inlet and pressure outlet respectively. Air is made
to flow through both the fire tubes at a velocity of 5 m/s with a temperature of 1500 K. Water
is made to pass through the fluid domain with varying velocities (25 m/s, 30 m/s, 35 m/s and
40 m/s) at a temperature of 350 K. The boiler shell material and fire tube material is chosen
accordingly and convection coefficient is set to 25 W/m2K along the interface. Simulation is
run to get the results.
3. RESULTS AND DISCUSSIONS

The inlet velocity of the water into the boiler is varied between 25 m/s, 30 m/s, 35 m/s and 40
m/s. The pressure induced inside the boiler is determined by simulation and presented in the
form of contours in Fig.3. Fig.4 and Fig.5 represents the variation of minimum and maximum
pressure with velocity in the form of graph.

Figure 3 Pressure plot for different inlet velocities of water
Figure 4 Minimum pressure (vacuum) variation with velocity

Figure 5 Maximum pressure variation with velocity

It can be seen from Fig.3, Fig.4 and Fig.5 that as the velocity of water increases inside the
boiler, the pressure encountered during the flow also increases. Greater pressure implies greater
stresses on the walls of the boiler. Hence, they are more susceptible to failure under high
pressure condition. As the velocity of the water increases, lesser heat will be transferred from
the hot gases to the water.
On varying the boiler casing material, significant changes can be seen in the amount of heat
that is being lost through the boiler shell. Fig.6. represents the heat flux contours, as obtained
by varying the boiler casing material. Table 2 states the loss of heat flux through the boiler.

Figure 6 Heat flux variation with boiler casing material
Table 2 Heat flux variation with respect to boiler casing material

Boiler Casing Material Negative Heat Flux ( W/m2 )
Steel 15.51
Brass 50.94
Stainless Steel 15.32
While selecting the boiler casing material, the key factor is the loss of heat through the
boiler casing. Greater the loss of heat, lower is the efficiency of the boiler. Among the three
materials tested, brass is having a very high negative heat flux of 50.94 W/m2. Steel and
stainless steel are nearly having the same negative heat flux value. Stainless steel is having the
lowest negative heat flux of 15.32 W/m2.

4. CONCLUSION
Flow of water and hot exhaust gases through the fire-tube boiler has been simulated using
ANSYS Fluent. In the first case, the inlet velocity of the water has been varied and the pressure
distribution across the boiler shell has been studied. In the second case, the boiler casing
material has been varied to identify the loss of heat through the boiler. In order to run the boiler
at greater efficiency, the following points needs to be considered.
1. It is recommended to keep the velocity of the water as low as possible to reduce the induced
pressure and increase the heat transfer.
2. Among the three boiler casing materials, stainless steel has minimum heat loss from the boiler
casing.
3. The preferability order among the three materials is – Stainless Steel > Steel > Brass.
REFERENCES
[1] Saurabh S. Kodak, Arjun M. Kshirsagar, Sagar M. Phadatare, Aniket V. Sawant Kedar,
Dayanand A. Ghatge, Shinghade J. Y, Wayse R. D, Design, Development and Analysis of
Non-IBR Vertical Fire Tube Boiler for Improving the Efficiency, International Journal of
Engineering Trends and Technology, 36, 2016, pp. 144-150.
[2] Gutiérrez Ortiz F.J., “Modeling of fire-tube boilers” Applied Thermal Engineering, 31(16),
2011, pp. 34-63.
[3] Branka Gaćeša, Vesna Milošević Mitić, Taško Maneski, Dražan Kozak, Josip Sertić,
“Numerical and Experimental Strength Analysis of Fire-Tube Boiler Construction”,
Technical Gazette 18(2), 2011, pp. 237-242.
[4] Liu S.W., Wang W.Z., Liu C.J., Failure analysis of the boiler water-wall tube, Case Studies
in Engineering Failure Analysis, 9, 2017, pp. 35–38.
[5] Bhargav Akkinepally, JaesoolShim, KisooYo, Numerical and experimental study on biased
tube temperature problem in tangential firing boiler, Applied Thermal Engineering, 126,
2017, pp. 92-99.
[6] Premkartikkumar SR, Annamalai K, and Pradeepkumar A R, Significance of Inlet Air
Temperature on Reducing Engine-out Emissions of DI Diesel Engine Operating under the
Influence of Oxygen Enriched Hydrogen Gas. Iranian Journal of Science and Technology
- Transactions of Mechanical Engineering, 38, 2014, pp. 57–68.
[7] Premkartikkumar SR, Annamalai K, Pradeepkumar A R, A Renewable Alternative Fuel for
Diesel Engines - Diesohol. Journal of Chemical and Pharmaceutical Sciences, 7, 2015, pp.
212–214.
[8] Premkartikkumar SR, Annamalai K, Pradeepkumar A R, Effectiveness of oxygen enriched
hydrogen-hho gas addition on direct injection diesel engine performance, emission and
combustion characteristics, Therm. Sci., 18(1), 2014 , pp. 259–268.
[9] Senthur N, Pradeep Kumar A R, Annamalai K, Premkartikkumar SR, Effect of emulsified
fuel on performance and emission characteristics in DI diesel engine, Journal of Chemical
and Pharmaceutical Sciences, 7, 2015, pp. 215–218.
[10] Dr. Md. Shamsul Hoque, Mohammad Ahad Ullah and Dr. Hamid Nikraz, Investigation of
Traffic Flow Characteristics of Dhakasylhet Highway (N-2) Of Bangladesh, Volume 4,
Issue 4, July-August (2013), pp. 55-65, International Journal of Civil Engineering and
Technology (IJCIET).

[11] Shahabaz Ahmad, Md.Tanwir Alam, Md. Arif Siddique and Akhter Husain Ansari,
Morphological and Flow Characteristics of Synthesized Polystyrene Composites, Volume
6, Issue 5, May (2015), pp. 17-24, International Journal of Mechanical Engineering and
Technology (IJMET)
[12] Vijaya Kumar Reddy S, Premkartikkumar SR, Radha Krishna Gopidesi and Nitin Uttamrao
Kautkar, A Review on Nano Coatings for IC Engine Applications, International Journal of
Mechanical Engineering and Technology, 8(9), 2017, pp. 70–76.
[13] N.G.Narve and N.K.Sane, Heat Transfer and Fluid Flow Characteristics of Vertical
Symmetrical Triangular Fin Arrays, Volume 4, Issue 2 March – April 2013, pp. 271-281,
International Journal of Advanced Research in Engineering and Technology (IJARET).

Ijmet 08 11 014

Uploaded by

Copyright:

Available Formats

Ijmet 08 11 014

Uploaded by

Document Information

Original Title

Copyright

Available Formats

Share this document

Share or Embed Document

Sharing Options

Did you find this document useful?

Is this content inappropriate?

Copyright:

Available Formats

Ijmet 08 11 014

Uploaded by

Copyright:

Available Formats

International Journal of Mechanical Engineering and Technology (IJMET)

© IAEME Publication Scopus Indexed

http://iaeme.com/Home/journal/IJMET 121 editor@iaeme.com

2. FORMULATION AND SOLUTION METHODOLOGY

Figure 1 Isometric view of the 3D fire-tube boiler

http://iaeme.com/Home/journal/IJMET 122 editor@iaeme.com

Table 1 Geometrical Specifications of 3D fire-tube model

Figure 2 Meshed fire-tube boiler model

3. RESULTS AND DISCUSSIONS

http://iaeme.com/Home/journal/IJMET 123 editor@iaeme.com

Figure 3 Pressure plot for different inlet velocities of water

Figure 4 Minimum pressure (vacuum) variation with velocity

http://iaeme.com/Home/journal/IJMET 124 editor@iaeme.com

Figure 5 Maximum pressure variation with velocity

http://iaeme.com/Home/journal/IJMET 125 editor@iaeme.com

Figure 6 Heat flux variation with boiler casing material

Table 2 Heat flux variation with respect to boiler casing material

http://iaeme.com/Home/journal/IJMET 126 editor@iaeme.com

http://iaeme.com/Home/journal/IJMET 127 editor@iaeme.com

http://iaeme.com/Home/journal/IJMET 128 editor@iaeme.com

You might also like