Location via proxy:   [ UP ]  
[Report a bug]   [Manage cookies]                

WS2812B Mini Worldsemi

Download as pdf or txt
Download as pdf or txt
You are on page 1of 10

WS2812B-Mini LED

Intelligent control LED integrated light source

WORLDSEMI CO.,LIMITED
WS2812B-Mini Datasheet and Specifications

Intelligent control LED integrated light source

Jan,2016
V1.0

www.world-semi.com/en 1 /10
WS2812B-Mini LED
Intelligent control LED integrated light source
Main Benefits
 The control circuit and the LED share the only power source.
 Control circuit and RGB chip are integrated in a package of 3535 components, form a complete
control of pixel point.
 Built-in signal reshaping circuit, after wave reshaping to the next driver, ensure wave-form distortion
not accumulate.
 Built-in electric reset circuit and power lost reset circuit.
 Each pixel of the three primary color can achieve 256 brightness display, completed 16777216 color
full color display, and scan frequency not less than 400Hz/s.
 Cascading port transmission signal by single line.
 Any two point the distance more than 5m transmission signal without any increase circuit.
 When the refresh rate is 30fps, cascade number are not less than1024 points.
 Send data at speeds of 800Kbps.
 The color of the light were highly consistent, cost-effective.

Main Applications
 LED Pixel light,LED Rigid Strip,LED Flexible Strip,LED Guardrail Tube,
 LED Point Light,LED Panel Screen,LED decorative lighting, Indoor/outdoor LED video irregular
screen.
 Small volume DIY Products.

www.world-semi.com/en 2 /10
WS2812B-Mini LED
Intelligent control LED integrated light source

General description
WS2812B-Mini is a intelligent control LED light source that the control circuit and RGB chip ar
e integrated in a package of 3535 components.So we named it as MINI WS2812B.
It internal include intelligent digital port data latch and signal reshaping amplification drive circ
uit. Also include a precision internal oscillator and a 12V voltage programmable constant current
control part, effectively ensuring the pixel point light color height consistent.
The data transfer protocol use single NZR communication mode. After the pixel power-on reset, t
he DIN port receive data from controller, the first pixel collect initial 24bit data then sent to th
e internal data latch, the other data which reshaping by the internal signal reshaping amplificati
on circuit sent to the next cascade pixel through the DO port. After transmission for each pixe
l,the signal to reduce 24bit. pixel adopt auto reshaping transmit technology, making the pixel ca
scade number is not limited the signal transmission, only depend on the speed of signal transmis
sion.

Mechanical Dimensions

www.world-semi.com/en 3 /10
WS2812B-Mini LED
Intelligent control LED integrated light source
PIN configuration

PIN function

NO. Symbol Function description


1 VDD Power supply LED
2 DOUT Control data signal output
3 VSS Ground
4 DIN Control data signal input

Absolute Maximum Ratings(TA=-25℃,VSS=0V,unless otherwise specified)


Parameter Symbol Ratings Unit
Power supply voltage VDD +3.5~+5.3 V
Input voltage VI -0.5~VDD+0.5 V
Operation junction
Topt -25~+85 ℃
temperature
Storage temperature range Tstg -40~+120 ℃

www.world-semi.com/en 4 /10
WS2812B-Mini LED
Intelligent control LED integrated light source
Electrical Characteristics
(TA=-20~+70℃,VDD=4.5~5.5V,VSS=0V,unless otherwise specified)
Parameter Symbol conditions Min Tpy Max Unit
Input current II VI=VDD/VSS —— —— ±1 µA
High voltage input VIH DIN,SET 0.7VDD —— —— V
Low voltage input VIL DIN,SET —— —— 0.3 VDD V

Hysteresis voltage VH DIN,SET —— 0.35 —— V

Switching characteristics

(TA=-20~+70℃,VDD=4.5~5.5V,VSS=0V,unless otherwise specified)


Parameter Symbol Condition Min Tpy Max Unit

Transmission delay time tPLZ CL=15pF,DIN→DOUT,RL=10KΩ —— —— 300 ns

Fall time tTHZ CL=300pF,OUTR/OUTG/OUTB —— —— 120 µs

Input capcity CI —— —— —— 15 pF

RGB Chip characteristic parameter

Emitting color Wavelength(nm) Lumen(mcd) Working Current(mA) Voltage(V)

Red 620-630 550-700 15 1.8-2.2


Green 526-527 1100-1400 15 3.5-3.7
Blue 465-467 200-400 15 3.5-3.7

www.world-semi.com/en 5 /10
WS2812B-Mini LED
Intelligent control LED integrated light source
Data transfer time( TH+TL=1.25µs±600ns)
T0H 0 code ,high voltage time 0.40us ±150ns

T1H 1 code ,high voltage time 0.85us ±150ns

T0L 0 code , low voltage time 0.85us ±150ns

T1L 1 code ,low voltage time 0.40us ±150ns

RES low voltage time Above 50µs

Sequential waveform

Sequence chart:

T0L
0 code
T0H

T1L
1 code
T1H

Treset
RET code

Cascade method:

D1 D2 D3 D4
DIN DO DIN DO DIN DO

PIX1 PIX2 PIX3

www.world-semi.com/en 6 /10
WS2812B-Mini LED
Intelligent control LED integrated light source
Data transmission method:

reset code
>=50us reset
code

Data refresh cycle 1 Data refresh cycle 2


seco n d seco n d
first 2 4 b it th ird 2 4 b it first 2 4 b it th ird 2 4 b it
D1 2 4 b it 2 4 b it

seco n d seco n d
th ird 2 4 b it th ird 2 4 b it
D2 2 4 b it 2 4 b it

th ird 2 4 b it th ird 2 4 b it
D3

D4

Note: The data of D1 is send by MCU,and D2, D3, D4 through pixel internal reshaping amplification to
transmit.

Composition of 24bit data:

G7 G6 G5 G4 G3 G2 G1 G0 R7 R6 R5 R4 R3 R2 R1 R0 B7 B6 B5 B4 B3 B2 B1 B0

Note: Follow the order of GRB to sent data and the high bit send at first.

www.world-semi.com/en 7 /10
WS2812B-Mini LED
Intelligent control LED integrated light source
Typical application circuit:

WS2812B-Mini Products Using Instructions


MSL=5A Level
1. Purpose:
WS2812B-Mini LED lamp’s surface use the high hardness silicone resin,can ensure that no
matter customers use PU glue or epoxy resin to do the silicone drop rubber
processing,won’t lead the LED to die;also has a very good anti sulfide capacity. Good
compatibility with bracket, but the silicon resin has a higher requirements on the humidity
and dehumidification process, especially pay attention during wet season,ensure the
production safety.
2. Transport and application area:
All WS2812S/B products during the transportation process, need to maintain a positive
upward, moisture-proof, during the transport process,shall avoid the extrusion, collision
and vibration.
3. Product storage and deadline:
Sealed storage at room temperature: 20 ℃ ~ 30 ℃, 40% ~ 60%RH, the product is valid
for 3 months;
Moisture seal storage: 20 ℃ ~ 30 ℃, 25% ~ 60%RH, the product is valid for 6 months;
After opening the product packaging , suggest using them within 1 hours,(environmental
conditions of temperature <30 ℃, humidity <60%).

4. Dehumidification process:
LED products which is beyond the prescribed time limit,or for getting damp for some other
reasons,we recommend the customer first do the dehumidification process,then use
them.Dehumidification method:under 75 ℃ / 22 ±2 hours.

5. Electrostatic protection:

www.world-semi.com/en 8 /10
WS2812B-Mini LED
Intelligent control LED integrated light source
LED is the electrostatic sensitive devices, although the LED product has excellent
anti-static ability, but after each ESD impact, will cause a certain degree of damage to LED.
Thus in using process of LED products, must do the electrostatic protection measures, such
as anti-static gloves, anti-static Bracelet etc..

6. Manual welding operation instruction


Suggest using the Electric soldering iron whose power is less than 30W, then control the
electric soldering iron’s temperature being not higher than 350 ℃ , every time when
welding electric iron in the bracket pin,stay time shall be no more than 3 seconds,if
requiring repeat welding,then interval time shall be no less than 2 seconds.Please don’t
touch or extrusion the LED’s surface,in order to avoid damage to the internal LED, at the
same time, please pay attention to avoid the electric iron burns the colloid on the surface of
LED and other injuries.

7. Reflow instructions
Set the reflow parameters, check the following drawing and table for reference.,
recommend using Senju, Alfa, Henkel loctite brand solder paste, recommends customers do
the necessary adjustments according to foundation of material properties provided by the
solder materials suppliers.

Curve description Lead in solder reflow SMT LINE

The lowest preheat temperature(Tsmin) 100℃ 150℃

The highest preheat temperature(Tsmax) 150℃ 200℃

Preheating time (Tsmin to Tsmax)(ts) 60-120 S 60-180 S

Average rate of temperature rise(Tsmax to Tp) <3℃/S <3℃/S

liquid phase temperature (TL) 183℃ 217℃

Holding time liquid region (tL) 60-150 S 60-150 S

peak temperature(Tp) 235 ℃ 250℃

High temperature region (the peak temperature <10 S <10 S


-5 ℃) residence time (tp)

Decreasing temperature rate <6℃/S <6℃/S

Stay time from room temperature to the peak <6 min <6 min
temperature

www.world-semi.com/en 9 /10
WS2812B-Mini LED
Intelligent control LED integrated light source

8.Notice of Production
1.All products ,during SMT, please carefully check, if the vacuum packaging intact, no
leakage phenomenon,Please use directly, can don’t do the bake dehumidification.
2. During use, please open a bag and use a bag,please don’t open many bags at one-time
which shall lead the LEDs absorb moisture in the air since you don’t use them at once.
3. After SMT,please do the reflow soldering furnace immediately,please don’t leave them in
in the pre-reflow for a long time which absorb moisture.Especially
when off work,please use out the LEDs which is out of packaging,please SMT and
reflow,do not let them stay in the air for a long time.
4. Dehumidification process,please under 70-75 ℃ , bake for 24 hours. Also note during
using, use the LEDs immediately after taking out of the bake box,please don’t take many
reels at one-time, since it is very hot when taking out,LED in the cooling process more
easily absorb the moisture in the air into the inside of the LED ,which shall cause led dead
during reflow.
5.Please pay attention that it is forbidden to secondary reflow soldering.

www.world-semi.com/en 10 /10

You might also like