Ariel Application Manual

Application Manual 12/13/2023
Table of Contents
Introduction . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 7
Copyright . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 7
Disclaimer . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 7
Revision History . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 8
Mission Statement . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 11
Vision Statement . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 11
Mission Statement . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 11
Quality Policy . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 11
General Contact . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 12
After Hours Support. . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 12
Ariel Response Center . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 13
Packager Standards . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 14
Customer Technical Bulletins . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 15
Frame Class Equipment . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 16
JGM:JGP Frames . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 16
JGN:JGQ Frames . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 16
JG:JGA Frames . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 17
JGM:JG:JGSP Cylinders . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 17
JGR:JGJ Frames . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 17
JGR:JGJ:JGE Cylinders . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 18
JGH Frame . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 18
JGE:JGT:JGK Frames. . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 19
KBK:KBT Frames. . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 19
K:T:C:D:Z:U:B:V Cylinders . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 20
JGC:JGD:JGF Frames. . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 20
KBZ:KBU Frames . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 20
KBB:KBV Frames. . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 21
JGI Standard Equipment . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 22
JGI Unbalanced Forces and Moments. . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 22
Tools . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 22
Definitions and Terms . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 23
ARIEL CORPORATION | www.arielcorp.com 1

Adjusted Equivalent Valve Area . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 23

Ambient Temperature. . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 23
Balanced Opposed Design . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 23
Clearance Volume . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 24
Compression Ratio. . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 24
Cylinder Action, Double Acting . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 25
Cylinder Action, Single Acting . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 25
Removing Suction Valves to Single Act . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 25
Suction valve Unloader . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 26
Head End Bypass Unloader . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 26
Cylinder Action, Tandem . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 27
Cylinder Hydro Test . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 27
Discharge Event . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 28
Elevation . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 28
Internal Rod Load, Gas . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 28
Piston Displacement . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 28
Pressure, Absolute . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 29
Pressure, Atmospheric . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 29
Pressure Drop . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 29
Pressure, Gauge . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 29
Pressure, Rated Discharge (RDP) . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 29
Rod Load, Inertia . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 30
Separable Compressor . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 30
Suction Temperature . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 30
Swept Volume . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 30
Thermodynamic Terms . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 31
Valve Lift. . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 33
Valve Velocity . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 34
Calculations . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 35
Ariel Calculation Method . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 35
Definitions / Units . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 37
Compressor Theory . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 37
Ideal P-V Diagram . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 37
Effect of Clearance Volume on Capacity . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 38
Effect of Clearance Volume. . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 38
Clearance Volume - Low Ratio . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 39

Adjusted Equivalent Valve Area. . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 39

Piston Rod Root Stress . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 39
Unit Conversions -Flow. . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 40
Unit Conversions - Volume. . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 40
Unit Conversions - Power . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 41
Unit Conversions - Pressure. . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 41
Unit Conversions - Length . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 41
Unit Conversions - Weight . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 42
Compressor . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 43
Frame . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 43
Crankshafts . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 43
Connecting Rods. . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 43
Crossheads . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 43
Frame Lube Oil System . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 44
Frame Driven Lube Oil Pumps . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 44
Aux End Pump Removal . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 44
Pre-lube Requirements . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 46
Lube Oil Filter . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 46
Lube Oil Cooler . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 46
Maximum Allowable Lube Oil Temperature . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 47
Minimum Allowable Lube Oil Temperature . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 47
Dry Sump . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 47
Maximum Frame Tilt for Offshore Applications . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 48
Distance Piece Arrangements . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 48
Short Single Compartment Distance Piece. . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 48
Long Single Compartment Distance Piece . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 48
Short Two Compartment Distance Piece . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 49
Long Two Compartment Distance Piece (Ariel Design) . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 49
Long Two Compartment Distance Piece (API 618 Type C, API 11P Type 3. . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 50
Balance Crossheads . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 50
Crankcase Relief Doors . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 50
Fan Shaft. . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 51
Frame Lube Oil Heaters. . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 51
Thermostatic Temperature Valve . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 52
Cylinder . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 52
Cylinder, Design Features . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 52
Water Jackets . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 52
Cylinder Liners. . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 53
ASME Section VIII Pressure Vessel Design . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 53
Cylinder Re-Bore Capability . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 53
Cylinder, Design Options. . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 53
Piston Rods . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 53
Piston Rings, Piston/Rider Rings & Wear Bands. . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 54
Water Cooled Packings . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 54
Purged Packings . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 55
Compressor Cylinder Lube Oil System. . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 56
Cylinder Lube Oil Supply. . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 56
Force Feed Lubricator Pump . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 58

Cylinder, Lube Oil Distribution Block System. . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 58

Cylinder lubricator no-flow Switch. . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 59
Tubing . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 60
Ion-nitriding . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 60
Tungsten Carbide Coating . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 61
Cylinder, Side-by-Side Clearance . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 61
Special Flange . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 61
Valves. . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 65
Commissioning and Operation of the Compressor. . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 65
Special Tools . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 66
Hand Tools . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 66
Industry Specification Comments and Exceptions. . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 67
Applications . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 68
Air Service . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 68
Carbon Dioxide . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 69
Carbon Monoxide . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 70
Gas Storage Service . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 71
High Gas Molecular Weight . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 71
Hydrogen Service . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 72
Non Lube Compressor Cylinders . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 72
Offshore Applications . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 73
Oxygen . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 75
Propane . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 75
Sour Gas . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 76
Optional Equipment for Sour Gas Service. . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 79
Wet Gas. . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 80
Gas Method . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 81
Gas Properties - Air . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 82
Gas Properties - Carbon Monoxide. . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 82
Gas Properties - Carbon Dioxide. . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 83
Gas Properties - Ethylene . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 84
Gas Properties - Helium . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 85
Gas Properties - Hydrogen . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 86
Gas Properties - Methane . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 86
Gas Properties - Natural Gas . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 87
Gas Properties - Nitrogen . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 88
Gas Properties - Propane . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 89

Performance Application Limits . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 90

Critical Projects . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 90
Project Reviews . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 91
Torsional Providers . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 91
Acoustical and Mechanical Providers. . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 91
High Discharge Pressure. . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 92
Low Suction Pressure . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 92
Vacuum Suction Pressure . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 92
Maximum Allowable Discharge Temperature . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 93
Maximum Allowable Working Pressure. . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 93
Maximum Allowable Internal Gas Rod Load . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 94
Minimum Allowable Pin Load Reversal . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 94
Maximum Allowable Reciprocating Weight . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 95
Rated Speed (Maximum Allowable Rotating Speed) . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 96
Rated Speed (Minimum Allowable Rotating Speed) . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 96
Maximum Allowable Piston Speed. . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 97
Frame Horsepower Limits . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 97
Minimum Volumetric Efficiency . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 97
Pseudo-Q Value . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 98
Cooled Packings . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 99
Non Intercooled . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 100
Capacity and Load Control . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 101
Variable Volume Clearance Pockets . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 102
High Clearance Valve Assembly . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 103
Pneumatic Fixed Volume Clearance Pockets. . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 104
Suction Valve Unloaders. . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 104
Head End Bypass Unloaders . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 105
Double Deck Volume Pockets . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 106
Deactivated Stage . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 107
Deactivated Cylinder . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 108
Non-Acting Cylinders . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 108
Distance Piece Purge and Vent Arrangements for Sour, Corrosive and Hazardous Gasses. . . . . . . . . 111
Options . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 111
Packing Leakage. . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 111
Purged Pressure Packing Cases . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 112

Purge and Vent Arrangements . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 112

Drivers . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 113
Electric Motor Drive . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 113
Process Application Definition. . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 116
Process Equipment Selection . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 116
Process Frame Cyl Design . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 117
Process Piston. . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 117
Process Rotative Speeds . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 118
Process Motor Sizing . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 118
Quality Assurance Programs . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 119
ISO 9001 Certification . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 119
Materials Certifications and Tests . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 119
Cylinder Leak Test . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 120
Assembly Inspections And Tests. . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 120
Studies and Analyses . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 121
Unbalanced Forces and Couples . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 121
Starting Torque . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 121
Torsional Vibration Analysis . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 122
Cylinder Numbering and Phasing. . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 125

Introduction
Welcome to the Ariel Application Manual. For any Copyright
questions or comments concerning the
DataBook or Application Manual, please contact This computer software and its associated data is
Ariel Applications Engineering at: protected by the Copyright Laws of the United
States. It is owned solely by Ariel Corporation and
E-mail: info@arielcorp.com is considered confidential. It is intended solely
Fax: (740) 397-3856 for use by the authorized recipient. Unauthorized
Voice: (740) 397-0311 modification or reproduction of any portion is
forbidden.
Disclaimer
Technical information changes all the time. Ariel
claims that the information in this document is
the latest at the time of publication. In all cases,
contact Ariel application engineering for issues
regarding specific applications.

Revision History
14 December 2023 • Added references to EN 10204:2004 to Mate-
• Modified the Sour Gas topic to revise flushing rials Certifications and Tests topic
lube recommendations. 8 October 2018
• Modified the Electric Motor Drive topic to
• Included the KBK:T frames.
exclude the Service Factor from the 10%
margin between rated driver power and • Added ability to purge wiper set with purged
maximum horsepower. packing on long single compartment
distance pieces for KBK:KBT and KBZ:KBU
11 January 2022 frames.
• Added maximum allowable inertia limit for 31 October 2016
fan drive shafts
• Added Valve Topic, to include low lift valve
• Converted to Adobe Experience Manager
discussion.
20 April 2021 • Modified Sour Gas topic due to the removal of
• Re-applied the Distance Piece Arrangements the "H2S" designation from forged steel
topic cylinders.
• Expanded the Minimum Allowable Pin • Modified Piston Rod topic for the piston rod
Reversal to help identify configurations to surface finish values.
review closer for acceptable reversal • Modified Tools and Special Tools topics to
remove specific components and refer to the
17 June 2020 Maintenance and Repair Manual.
• Modified the discharge temperature topic to • Modified Cooled Packing topic to better
better define the Application Limit versus the define when to provide a packing cooling
Maximum Shutdown Limit. system.
• Added a topic on Oxygen. 8 July 2016
29 May 2019 • Added Auxiliary End Pump Removal topic.
• Added information on VVCP stem seal vent, • Added reference within Torsional Vibration
which cylinders have the two seal vent. Analysis to ER-83.
• Removed cylinder options / features table, • Modified Ariel Special Flange topic to provide
referring to the Performance Software for the definition of the Taperlok flange ASME Div 1
list of features and options. design basis.
20 February 2019 16 July 2015
• Modified water cooled packing and non-lube • Modified Ariel Special Flange topic to include
topics to be more concise that packing the alloy steel material designation for the
cooling requires the water cooling system higher pressure 2-5/8x10-FS-HE 10,000 psi
applied cylinder.
• Added allowance for non-lubricated cylinder 9 March 2015
construction for Sour Level 1 service (Non-
lube and Sour Gas topics) • Modified ISO-9001 topic to refer to the ISO
statement on the website.
19 November 2018

Application Manual – Revision History 12/13/2023
• Removed unit conversion calculation fields • Removed references for Purge and Vent
from the unit conversions due to instability Systems in favor of the Packager Standards
with various browsers. Section 8 Packing and Distance Piece Vent
Systems.
29 September 2014
• Included a low temperature cautionary note 15 July 2012
to the Suction Temperature and Ambient • Added Air Service topic.
Temperature topics for o-ring sealing below - • Added selection recommendations to the
15 F. Carbon Dioxide Service topic.
17 April 2014 • Added Gas Properties topic.
• Added Crankcase Relief Door topic.
• Modified the Sour Gas topic to further stress
the importance of safety, changing the • Added Selection Recommendations to the
recommendations for purged packing, two Sour Gas topic.
compartment distance pieces (short or long) 11 November 2011
and stainless steel piston rod material to
required options. • Better defined those variables impacted by
speed range on the Minimum Allowable
• Modified the Carbon Dioxide Service topic to
Rotating Speed topic.
allow the use of 400 series stainless steel
valve body material in CO2 service. 400 series • Added the 19BL:VL:BM:VM cylinder to the
stainless steel material is the supplied stan- Ariel Special Flange list for special peanut
dard for the majority of the valves in Ariel type flanges.
cylinders. This allows for the use of standard • Added a Project Engineering Checklist to the
valve material in CO2 service if the standard Electric Motor topic.
material is 400 series stainless steel. 22 December 2010
26 July 2013 • Removed frame lube oil viscosity and
• Updated to re-organize table of contents and temperature information in favor of refer-
function on greater number of web plat- encing the Packager's Standards, for a single
forms. location of information.
• Added gas properties for some of the more 22 October 2009
common gasses encountered in compres-
sion. • Added a watt density limit to the frame lube
oil heater topic.
• Added an FPSO topic
• Added a Carbon Monoxide topic 25 October 2008
• Simplified the Calculation Method discus- • Added a Tools topic discussing the hydraulic
sions torque tools and the SAE hand tools as a
• Added Project Check List to the Torsional performance software option.
topic • Added the discussion of the SG tandem
• Added the JGF frame designation to the cylinder high clearance valve assemblies to
JGC:D:F frame class the High Clearance Valve Assembly topic.
14 September 2012 7 March 2007
• Updated to provide changes in links to a fully • Modified Capacity and Load Control topic to
revised Packager Standards. include a load sequence hierarchy (including
notes and links within the Torsional and

Application Manual – Revision History 12/13/2023
Cylinder Single Acting topics to Capacity and • Added Gas Method page defining the usage of
Load Control topic). VMG and Hall gas methods.
• Removed Frame Thermal Growth topic. • Added the JGJ/4 fan shaft, a new addition to
Please refer to the same topic presented in the line of fan shafts, suitable for 50 hp.
the Packager's Standards, Technical Manuals
and Outline Drawings. 2 November 2006
• Revised Low Suction Temperature Applica- • Various pages: Changed JGB:V frame refer-
tions Topic to be Suction Temperature, ences to KBB:V frames.
discussing low suction temperature, high • Modified frame tilt data for the JGB:V and
suction temperature and high mean cylinder KBB:V frames.
gas temperature. • Sour Gas: Changed recommendations for
• Added Non-Intercooled Topic. S2C guides to allow for Long Single guides at
• Modified Ariel Calculation Method to remove lower levels of H2S when the S2C guide is not
critical temperature and pressure references. made available by Ariel (JGU:Z, KBB:V cylin-
• Removed the No Yellow Metals topic from the ders and some -VS cylinders).
Sour Gas topic.
23 February 2007
• Corrected Frame Driven Lube Oil Pump
discussion for the large frames that have
external pressure relief valves downstream of
the lube oil filter.
28 December 2006
• Modified Deactivated Stage topic, added clar-
ification for the durations of blowthru and
pulling suction valves.
• Added Special Tools topic for Hydraulic
torque tools.
• Modified Helium Leak Test topic, added the
mole weight and hydrogen content requiring
He test.
6 December 2006
• Modified Assembly Inspections and Tests
topic, added "prepared for shipment" in last
bullet point.
• Modified Cylinder Hydro Test topic, changed
ISO reference to match current ISO procedure
numbers.
• Modified Helium Leak Test topic, changed
ISO reference to match current ISO procedure
numbers.
• Packager's Standards topic, added sub-
section links.
6 November 2006

Mission Statement
Vision Statement products that can be manufactured, installed,

and serviced with ease. Our compressors are
Ariel sets the world standard in gas compression, designed to match available drivers, offer
shaping the future of the compression industry – maximum efficiency and value, and continue to
a global company addressing emerging energy be the most reliable compressors attainable.
and environmental challenges. From wellhead
We will maintain our core tradition of standing
to burner, Ariel = compression.
behind our products with fair and generous
warranties, with broad technical and educational
Mission Statement support, and with fairly-priced, rapid spare parts
delivery.
In order to achieve our vision, we will apply our
compression expertise wherever natural gas is Our key processes incorporate the best aspects
found. We will identify opportunities and capture of world class manufacturing practices. Our
market share in every viable compression quality system is certified to the requirements of
market. We will maintain and expand our market ISO 9001. Key performance metrics supporting
share by offering unparalleled products, service, continual improvement will be communicated
and innovative engineering. We will maintain our throughout the organization. Yearly objectives
core tradition of supporting our products with a will be established for performance metrics and
fair and generous warranty policy, with broad reported at the management review of the
technical and educational support, and with quality system.
fairly-priced, fast response replacement parts.
Quality Policy
Ariel people take pride in the company’s world
class manufacturing processes and product
designs. Quality is the foundation of our success. Alex Wright/CEO
Maintaining our reputation as the world standard
compression company requires us to design

General Contact
Phone Fax Email
Main Switchboard (740) 397-0311 (740) 397-3856
Order Entry (740) 397-3602

International
Spare Parts (888) 397-7766 Domestic (740) 393-5054 spareparts@arielcorp.com
Ariel Response Center (740) 397-1060 arc@arielcorp.com
Ariel Field Service (740) 397-0311 (740) 397-3856
Ariel Corporation These numbers are in addition to the general

35 Blackjack Road numbers that are used during regular business
Mount Vernon, OH 43050 USA hours. Regular business hours at Ariel are 8:00
www.arielcorp.com a.m. to 5:00 p.m. for office hours, 8:00 a.m. to 8:00
p.m. for Spare Parts office hours and 8:00 a.m. to
7:00 p.m. for Ariel Response Center hours,
After Hours Support Eastern time, Monday thru Friday, excluding
national holidays.
Ariel 24 Hour, 7 Day a Week, Emergency Help
Phone Lines Emergency Field Service technical assistance
and Emergency Spare Parts service are available
Ariel has available emergency after hour phone
after hours at (740)397-3602 International and
numbers for the Field Service and Spares
(888)397-7766 North America. Emergency Field
Departments.
Service technical assistance and Spare Parts calls
will be handled automatically by an individual
responsible for coverage of emergency situations
when a detailed message is left on the above
phone numbers.

Ariel Response Center

Ariel has developed a staff of experienced • Ariel products and data
personnel who are ready to provide quick, • Assembly questions
accurate information on topics that you face in • Reconfiguration assistance
compressor design, operation, and • Balance and lubrication information
maintenance. • Unit specific as-built information
• Valve selection assistance
Whether you just need a torque value for a
• Recommended spare parts
fastener or assistance in a total reconfiguration,
• Product conversions
you can contact this team during our extended
business hours of 8:00 am to 7:00 p.m. Eastern Phone: 888-397-7766 (North America) / 740-397-
Time. 3602 (International)
Fax: 740-397-1060
Call now for information concerning:
E-mail: ARC@arielcorp.com

Packager Standards
Ariel provides guidance and standards on how to The Ariel Reciprocating Packager Standards can
build a successful reciprocating compressor be found through the Ariel website.
package around the Ariel compressor. These are
minimum requirements for packager quality and
design. Ariel encourages our packagers to exceed
these standards with the finest quality packages.

Customer Technical Bulletins

Current Customer Technical Bulletins are
available through the Internet at
www.arielcorp.com

Frame Class Equipment

• Mechanical running test with cylinders
mounted
JGM:JGP Frames For cylinder information refer to M, P, SP, JG

Cylinders.
ARIEL balanced/opposed, multi cylinder, gas
compressor arranged for clockwise rotation
when facing the drive end of the compressor JGN:JGQ Frames
(standing on the driver looking at the ARIEL balanced/opposed, multi cylinder, gas
compressor). Designed for operation with compressor arranged for clockwise rotation
appropriate engine, electric motor, turbine or when facing the drive end of the compressor
other prime mover. Includes the following (standing on the driver looking at the
standard equipment: compressor). Designed for operation with
• Heavy-duty, horizontal balanced/opposed, appropriate engine, electric motor, turbine or
moisture and dust-proof compressor frame. other prime mover. Includes the following
• Forged steel crankshaft standard equipment:
• Precision insert tri-metal bearings.
• Heavy-duty, horizontal balanced/opposed,
• Strong, H-beam design ductile iron moisture and dust-proof compressor frame.
connecting rods.
• Forged steel crankshaft.
• Short close coupled guide is standard and
• Precision insert tri-metal bearings.
integral with the compressor frame.
• Strong, H-beam design forged steel
• Lubricating oil pump with system relief valve
connecting rods.
for full pressure lubrication to bearings and
• Short close coupled guide is standard and
crossheads. (See Frame Lube Oil System)
integral with the compressor frame.
• Manual lube oil priming pump is available as
an option
• Frame mounted full-flow lube oil filter with
crossheads. (See Frame Lube Oil System )
inlet and outlet pressure gauges
• Manual lube oil priming pump is available as
• Lube oil strainer and stainless steel lube oil
an option
tubing with plated steel fittings
• Crankcase oil breather
• Oil level sightglass
• Lube oil strainer and stainless steel lube oil
• Force-feed lubricator pump(s) with block tubing with plated steel fittings
distribution system, cycle indicator / and no-
• Crankcase oil breather
flow shutdown(s), and stainless steel tubing
• Oil level sightglass
with plated steel fittings for cylinders and
packing. (See Compressor Cylinder Lube Oil • Force-feed lubricator pump(s) with block
System) distribution system, cycle indicator / and no-
flow shutdown(s), and stainless steel tubing
• Special wrenches and tools
with plated steel fittings for cylinders and
• Instruction manual and parts lists in elec-
packing. (See Compressor Cylinder Lube Oil
tronic format
System)

Application Manual – Frame Class Equipment 12/13/2023
• Special wrenches and tools with plated steel fittings for cylinders and
• Instruction manual and parts lists in elec- packing.(See Compressor Cylinder Lube Oil
tronic format System)
• Mechanical running test with cylinders • Special wrenches and tools
mounted • Instruction manual and parts lists in elec-
tronic format
For cylinder information refer to M, P, SP, JG
• Mechanical run test with cylinders mounted
Cylinders.
For cylinder information refer to M, P, SP, JG
Cylinders.
JG:JGA Frames
ARIEL balanced/opposed, multi cylinder, gas JGM:JG:JGSP Cylinders
• Horizontal single or double acting, non-
when facing the drive end of the compressor
cooled compressor cylinders.
(standing on the driver looking at the
• Plugged indicator cock connections on the
compressor). Designed for operation with head-end and crank-end of most cylinders
appropriate engine, electric motor, turbine or • SAE series 4100 steel piston rods, ion-nitrided
other prime mover. Includes the following with rolled threads. 17-4PH stainless steel
standard equipment: piston rods available as an option
• Heavy-duty, horizontal balanced/opposed, • Pistons of scuff-resistant gray iron or ductile
moisture and dust-proof compressor frame. iron
• Forged steel crankshaft • Non-metallic piston rings
• Precision insert tri-metal bearings. • Pistons with piston/rider rings standard for
• Strong, H-beam design forged steel 13-1/2JG and 1-3/4M-FS cylinders, and avail-
connecting rods able as an option on all other M, P and JG
cylinders. (See Piston Rings, Piston/Rider
• Short close coupled guide standard. Short
Rings & Wear Bands )
two compartment and long two compart-
ment distance piece are available as an • Full floating, vented rod and wiper packings
option • Profiled plate type valves with non-metallic
• Built-in crank end cylinder support valve plates.
for full pressure lubrication to bearings and JGR:JGJ Frames
crossheads. (See Frame Lube Oil System )
• Manual lube oil priming pump is available as ARIEL balanced/opposed, multi cylinder, gas
an option compressor arranged for clockwise rotation
• Frame mounted full-flow lube oil filter with when facing the drive end of the compressor
inlet and outlet pressure gauges (standing on the driver looking at the
• Lube oil strainer and stainless steel lube oil compressor). Designed for operation with
tubing with plated steel fittings appropriate engine, electric motor, turbine or
• Crankcase oil breather other prime mover. Includes the following
• Oil level sightglass standard equipment:
• Force-feed lubricator pump(s) with block
distribution system, cycle indicator / and no- • Heavy-duty, horizontal balanced/opposed,
flow shutdown(s), and stainless steel tubing moisture and dust-proof compressor frame

• Forged steel crankshaft • Non-metallic piston/rider rings (Piston Rings,

• Precision insert tri-metal bearings Piston/Rider Rings & Wear Bands)
• Strong, H-beam design forged steel • Full floating, vented rod and wiper packings
connecting rods • Profiled plate type valves with non-metallic
• Short close coupled guide standard. Short valve plates.
two compartment distance piece is available
as an option. Long two compartment (Ariel
design) distance piece, is available for JGW JGH Frame
frames with 8-7/8W or R cylinders.
ARIEL balanced/opposed, multi cylinder, air or
• Full floating, vented rod and wiper packings
gas compressor arranged for clockwise rotation
crossheads. (See Frame Lube Oil System ) (standing on the driver looking at the
• Manual lube oil priming pump is available as compressor). Designed for operation with
an option appropriate engine, electric motor, turbine or
• Frame mounted full-flow lube oil filter with other prime mover. Includes the following
inlet and outlet pressure gauges standard equipment:
• Lube oil strainer and stainless steel lube oil • Heavy-duty, horizontal balanced/opposed,
tubing with plated steel fittings moisture and dust-proof compressor frame
• Crankcase oil breather • Forged steel crankshaft
• Oil level sightglass • Precision insert tri-metal bearings
• Force-feed lubricator pump(s) with block • Strong, H-beam design ductile iron
distribution system, cycle indicator / and no- connecting rods
flow shutdown(s), and stainless steel tubing • Long single compartment distance piece
with plated steel fittings for cylinders and standard. short two compartment and long,
packing. (See Compressor Cylinder Lube Oil two compartment (API-618 Type C) distance
System) pieces are available as options.
• Special wrenches and tools • Lubricating oil pump with system relief valve
• Instruction manual and parts lists in elec- for full pressure lubrication to bearings and
tronic format crossheads. (Frame Lube Oil System)
• Mechanical run test with cylinders mounted • Manual lube oil priming pump is available as
For cylinder information refer to R, RJ Cylinders. an option
JGR:JGJ:JGE Cylinders • Lube oil strainer and stainless steel lube oil
tubing with plated steel fittings
• Horizontal single or double acting, ion-
nitrided, non-cooled compressor cylinders. • Crankcase oil breather
• Plugged indicator cock connections on the • Oil level sightglass
head-end and crank-end of most cylinders. • Force-feed lubricator pump(s) with block
• SAE series 4100 steel piston rods, ion-nitrided distribution system, cycle indicator / and no-
with rolled threads. 17-4PH stainless steel flow shutdown(s), and stainless steel tubing
piston rods available as an option with plated steel fittings for cylinders and
packing. (Compressor Cylinder Lube Oil
• Pistons of scuff-resistant gray iron or ductile
System)
iron

• Special wrenches and tools • Special wrenches and tools

• Instruction manual and parts lists in elec- • Instruction manual and parts lists in elec-
tronic format tronic format.
• Mechanical run test with cylinders mounted • Mechanical run test with cylinders mounted
For cylinder information refer to ET Cylinders. For cylinder information refer to ET Cylinders and
T, K Cylinders.
JGE:JGT:JGK Frames
KBK:KBT Frames
ARIEL balanced/opposed, multi cylinder, air or
gas compressor arranged for clockwise rotation ARIEL balanced/opposed, multi cylinder, air or
when facing the drive end of the compressor gas compressor arranged for clockwise rotation
(standing on the driver looking at the when facing the drive end of the compressor
compressor). Designed for operation with (standing on the driver looking at the
appropriate engine, electric motor, turbine or compressor). Designed for operation with
other prime mover. Includes the following appropriate engine, electric motor, turbine or
standard equipment: other prime mover. Includes the following
• Heavy-duty, horizontal balanced/opposed, standard equipment:
moisture and dust-proof compressor frame • Heavy-duty, horizontal balanced/opposed,
• Forged steel crankshaft moisture and dust-proof compressor frame
• Precision insert tri-metal bearings • Forged steel crankshaft
• Strong, H-beam design forged steel • Precision insert tri-metal bearings
connecting rods • Strong, H-beam design forged steel
• Long single compartment distance piece connecting rods
standard. short two compartment and long, • Long single compartment distance piece
two compartment (API-618 Type C) distance standard. Long, two compartment (API-618
pieces are available as options. Type C) distance piece is available as an
• Lubricating oil pump with system relief valve option.
for full pressure lubrication to bearings and • Lubricating oil pump with system relief valve
crossheads. (Frame Lube Oil System) for full pressure lubrication to bearings and
• Manual lube oil priming pump is available as crossheads. (Frame Lube Oil System)
an option • Frame mounted full-flow lube oil filter with
• Frame mounted full-flow lube oil filter with inlet and outlet pressure gauges
inlet and outlet pressure gauges • Lube oil thermostatic valve integrally
• Lube oil strainer and stainless steel lube oil mounted to frame oil filter header
tubing with plated steel fittings • Lube oil strainer and stainless steel lube oil
• Crankcase oil breather tubing with plated steel fittings
• Oil level sightglass • Crankcase oil breather
• Force-feed lubricator pump(s) with block • Oil level sightglass
distribution system, cycle indicator / and no- • Force-feed lubricator pump(s) with block
flow shutdown(s), and stainless steel tubing distribution system, cycle indicator / and no-
with plated steel fittings for cylinders and flow shutdown(s), and stainless steel tubing
packing. (Compressor Cylinder Lube Oil with plated steel fittings for cylinders and
System)

packing. (Compressor Cylinder Lube Oil • Strong, H-beam design forged steel
System ) connecting rods
• Special wrenches and tools • Long single compartment distance piece
• Instruction manual and parts lists in elec- standard. Short two compartment and long,
tronic format. two compartment (API-618 Type C) distance
• Mechanical run test with cylinders mounted pieces are available as options.
For cylinder information refer to T, K Cylinders. for full pressure lubrication to bearings and
crossheads. (Frame Lube Oil System)
• Frame lube oil priming pump, electric motor
K:T:C:D:Z:U:B:V Cylinders driven, supplied by Packager
• Horizontal single or double acting, ion- • Frame mounted lube oil filter with inlet and
nitrided, non-cooled compressor cylinders. outlet pressure gauges
• Plugged indicator cock connections on the • Lube oil strainer and stainless steel lube oil
head-end and crank-end of most cylinders. tubing with plated steel fittings
• Standard and pipeline cylinders available. • Crankcase oil breather
• SAE series 4100 steel piston rods, ion-nitrided • Oil level sightglass
with rolled threads. 17-4PH stainless steel • Force-feed lubricator pump(s) with block
piston rods available as an option distribution system, cycle indicator / and no-
• Pistons of scuff-resistant gray iron or ductile flow shutdown(s), and stainless steel tubing
iron with plated steel fittings for cylinders and
• Non-metallic piston rings packing. (Compressor Cylinder Lube Oil
• One-piece, angle cut, non-metallic wear System)
bands. (Piston Rings, Piston/Rider Rings & • Special wrenches and tools
Wear Bands) • Instruction manual and parts lists in elec-
• Full floating, vented rod and wiper packings tronic format
• Profiled plate type valves with non-metallic • Mechanical run test with cylinders mounted
valve plates.
For cylinder information refer to C, D, F Cylinders.
JGC:JGD:JGF Frames
KBZ:KBU Frames
compressor arranged for clockwise rotation ARIEL balanced/opposed, multi cylinder, gas
when facing the drive end of the compressor compressor arranged for clockwise rotation
(standing on the driver looking at the when facing the drive end of the compressor
compressor). Designed for operation with (standing on the driver looking at the
appropriate engine, electric motor, turbine or compressor). Designed for operation with
other prime mover. Includes the following appropriate engine, electric motor, turbine or
standard equipment: other prime mover. Includes the following
standard equipment:
• Heavy-duty, horizontal balanced/opposed,
moisture and dust-proof compressor frame • Heavy-duty, horizontal balanced/opposed,
• Forged steel crankshaft moisture and dust-proof compressor frame
• Precision insert tri-metal bearings • Forged steel crankshaft
• Precision insert tri-metal bearings

• Main bearing temperature devices • Heavy-duty, horizontal balanced/opposed,

• Strong, H-beam design forged steel moisture and dust-proof compressor frame
connecting rods • Forged steel crankshaft with integral flanged
• Long single compartment distance piece crankshaft hub
standard. Long two compartment (API-618 • Precision insert tri-metal bearings
Type C) distance pieces are available as an • Main bearing temperature devices
option. • Strong, H-beam design forged steel
• Lubricating oil pump with system relief valve connecting rods
for full pressure lubrication to bearings and • Long single compartment distance piece
crossheads. (Frame Lube Oil System) standard. Long two compartment (API-618
• Frame lube oil priming pump, electric motor Type C) distance pieces are available as an
driven, supplied by Packager option.
• Frame mounted lube oil filter with inlet and • Lubricating oil pump with system relief valve
outlet pressure gauges for full pressure lubrication to bearings and
• Lube oil strainer and stainless steel lube oil crossheads. (Frame Lube Oil System)
tubing with plated steel fittings • Frame lube oil priming pump, electric motor
• Crankcase oil breather driven, supplied by Packager
• Oil level sightglass • Frame mounted lube oil filter with inlet and
• Force-feed lubricator pump(s) with block outlet pressure gauges
distribution system, cycle indicator / and no- • Lube oil strainer and carbon steel lube oil
flow shutdown(s), and stainless steel tubing piping with steel flanges
with plated steel fittings for cylinders and • Crankcase oil breather
packing. (Compressor Cylinder Lube Oil • Oil level sightglass
System) • Force-feed lubricator pump(s) with block
• Special wrenches and tools (Hydraulic tools distribution system, cycle indicator / and no-
and pumps are required and priced sepa- flow shutdown(s), and stainless steel tubing
rately) with plated steel fittings for cylinders and
• Instruction manual and parts lists in elec- packing. (Compressor Cylinder Lube Oil
tronic format System )
• Mechanical run test with cylinders mounted • Special wrenches and tools (Hydraulic
tensioning tools and pumps are required and
For cylinder information refer to Z, U Cylinders.
priced separately)
KBB:KBV Frames tronic format
• Mechanical run test with cylinders mounted
For cylinder information refer to B, V Cylinders.
(standing on the driver looking at the
compressor). Designed for operation with the
appropriate engine, electric motor, turbine, or
other prime mover. Includes the following
standard equipment:

JGI Standard Equipment Primary Secondary
Ariel, vertical single throw air or gas compressor Horizontal 260 0

force, lbs
arranged for counter-clockwise rotation when
facing the drive end of the compressor (looking Horizontal 0 0
couple, lbs
at the compressor crankshaft stub) and designed
for operation with appropriate engine, motor, Vertical force, 1520 380
lbs
belt drive arrangement, with standard
equipment including: Vertical couple, 0 0
lb-ft
• Heavy duty, vertical, moisture and dust proof
compressor frame
• Gray Iron crankshaft Tools
• Strong, H-beam design connecting rods
• Vertical, single or double acting non-cooled Ariel compressors are provided with special
compressor cylinders tools, and have a number of optional tools
• Short, close coupled distance piece available. All available tools are listed in the Ariel
• Lubricating oil pump with system relief valve performance software to allow separate
for full pressure lubrication to bearings and purchase. Details on the special tools, and what
crosshead is included or recommended for each frame or
• Manual lube oil priming pump is available as tool option, can be found on the Ariel website
an option within the Maintenance and Repair Manuals.
• Frame mounted full-flow lubricating oil filter
with in and out pressure gages Ariel compressors are built with some special
• Lube oil strainer and stainless steel lube oil tool requirements. Special tools that are not
tubing with plated steel fittings available through standard tool suppliers are
• Crankcase oil breather provided by Ariel with each compressor.
• Oil level sight glass
Some compressor frames require (or
• Force feed lubricator with distribution block
system, cycle indicator/electric no-flow shut- recommend) the use of hydraulic tensioning
down switch, and stainless steel tubing with devices. As these may be needed for each site,
plated steel fittings for cylinders and packing rather than each compressor frame, they are
• Special wrenches and tools provided as an optional purchase.
Ariel compressors are built using SAE fasteners.
tronic format
As SAE tools are not readily available in all
• Mechanical running test with cylinder
mounted installation locations, an option to provide SAE
tools is available in the Ariel performance
software.
JGI Unbalanced Forces and
Further information on Special Tools can be
Moments found on the Ariel website within the
Based upon 800 rpm operation, largest available Maintenance and Repair Manuals.
cylinder bore:

Definitions and Terms

idle periods. If the gas release is of concern, it is
recommended that the unit be allowed to warm
up in a relatively unloaded state (low or no gas
Adjusted Equivalent Valve pressure and start up bypass line fully open) until
Area the equipment reaches warmer temperatures.
Adjusted equivalent valve area is a measure of

the effective orifice area of the complete valve Balanced Opposed Design
assembly. This is a useful term to compare valve
designs, as a valve with a higher adjusted Ariel compressors (except the JGI) are a
equivalent area will generally have a lower horizontal balanced opposed design. This design
pressure drop and better efficiency. utilizes throws with equal amounts of
reciprocating weight on opposite sides of the
See the compressor theory section for additional frame to minimize horizontal forces. To achieve
information regarding adjusted equivalent valve this balance, a combination of different weight
area as compared to the valve lift area. crossheads and crosshead nut weights are used
to achieve equal weights on opposing throws
with different size / weight pistons. The
Ambient Temperature maximum unbalance of reciprocating weight
Ambient temperature is the surrounding between opposite throws is:
temperature at a compressor installation. The
Maximum Unbalance of
range of ambient temperatures is required for
Reciprocating Weight
the proper application of gas coolers, drivers, Frame
Between Opposite
and auxiliary systems. Throws, lbs
JGM, JGP, JGN, JG, JGQ, 1.0

Ariel does not limit services based upon low
JGA, JGR, JGJ
ambient temperatures. Please refer to Section 6
JGH, JGE, JGK, JGT, KBK, 2.5
of the Packager Standards for frame oil heating
KBT, JGC, JGD, JGF
requirements for starting and loading purposes.
KBZ, KBU, KBB, KBV 5.0
Also see Suction Temperature topic for
information on low gas suction temperatures. Some combinations of larger cylinders opposite
much smaller cylinders may not balance on
Note: There is a potential for o-rings to lose
opposite throws. The Ariel performance software
flexibility while at lower temperatures, at or
will provide these limitations.
below -10 F (-23 C). This temporary loss of
flexibility may result in potential gas release at For balancing opposing throws with the same
the o-ring sealing joints on the cylinders when cylinder size, use the lightest crosshead / nut
under pressure. The lower temperatures occur combination. For balancing opposing throws
with either low inlet gas temperatures during with different piston sizes, pick the heaviest
operation or low ambient temperatures during piston and rod assembly, and use the lightest

Application Manual – Definitions and Terms 12/13/2023
crosshead / balance nut combination. For the Pneumatic Fixed Volume Clearance Pocket
lighter piston and rod assembly, choose the
Double Deck Volume Clearance Pocket
crosshead / balance nut combination that will
match the first throws' reciprocating weight
within the tolerances in the table above. Compression Ratio
For balancing opposite a blank throw a balance Compression ratio is defined as the discharge
crosshead may need to be used if a standard pressure divided by the suction pressure of a
crosshead is not sufficient in weight. It must be given stage of compression. Compression ratio is
noted that a balance crosshead requires a used in the equations for discharge temperature,
balance crosshead guide which is not suitable for volumetric efficiency, discharge event, power
mounting a cylinder. and rod load.
Reciprocating weights are balanced on opposing Compression ratios are typically in the range of 2
throws. Reciprocating weights are not balanced to 4 for gathering applications and typically
end to end, across adjacent throws. below 2 for pipeline applications.
Contact Ariel Application Engineering for any Higher compression ratios will result in higher
questions or problems concerning reciprocating discharge temperatures, lower volumetric
weight balance. efficiencies and lower valve discharge events.
Typically, the upper end of the compression
Clearance Volume ratio is limited by reaching a maximum discharge
temperature or low volumetric efficiency. Some
Cylinder clearance volume is the volume of gas gasses with lower ratio of specific heat values (k
left in the cylinder at the discharge end of the or N) can reach higher compression ratios before
stroke. It includes the space between the piston being limited by discharge temperature. Some
and cylinder head, the volume of the valves, cylinders with lower volumetric clearance can
valve pockets and any added clearance. reach higher compression ratios before being
Clearance volume is generally expressed as a limited by volumetric efficiency. This makes
percentage of the swept volume of a given limiting the upper end of compression ratio
cylinder end. subjective.
The main difficulty with higher compression

ratios is the loss of flexibility of operating
Changes in the clearance volume of a conditions. Higher compression ratios result in a
compressor cylinder will affect the throughput greater sensitivity to changes in suction and
and power requirements of that cylinder. Refer to discharge pressure. This can limit the useful
the compressor theory topic for additional operating range of an application. Higher ratios
information. Additional clearance can be added also have an adverse effect on compressor valve
to Ariel cylinders using the following devices: performance and reliability.
High Clearance Valve Assembly
Variable Volume Clearance Pocket

Rod load is a function of the suction and Figure: Double Acting Cylinder
discharge pressures within a cylinder, so are also
impacted by the compression ratio. High
compression ratios generally result in higher rod
load values. Small changes in pressures at higher
ratios can result in larger changes in rod load.
When compression ratios are in the higher range,

any clearance pocket devices should be checked
for full range use. With higher ratios, clearance Cylinder Action, Single Acting
has a much greater effect on the volumetric
efficiency. If the clearance pockets cannot be A single acting cylinder compresses gas on only
used fully at the higher compression ratios, either the instroke or outstroke of the piston.
considerations should be made to either limit the Double acting cylinders can be operated in a
use of the pockets, or to omit clearance pocket single acting mode by removing the suction
devices from the cylinders. valves from one end, by using valve plate
depressor type suction valve unloaders, or by
When no other flags exist, a good practical limit
using a head end bypass unloader.
for the higher end of the compression ratio range
is 4.5 ratios. A warning has been placed in the All single acting operating cases need special
performance software to flag this ratio to help review. Single acting conditions can create low
draw attention to the possible difficulties. When crosshead pin reversal, torsional resonance
this warning flag occurs, the specific application responses or acoustical resonance responses. A
must be reviewed for the applicability of the full review of the potential operating conditions
compression ratio for the specific operating in single acting mode must be made. This is to
range. include across the entire pressure range and
speed range.
Cylinder Action, Double Acting

Removing Suction Valves to Single
A double acting cylinder compresses gas on the Act
instroke and outstroke of the piston. This
requires suction and discharge valves on both All suction valves on one end of the cylinder can
ends (head end and crank end) of the cylinder. be removed for single acting configuration.
Typically head end suction valves are removed,
As gas is being compressed in the head end on
allowing compression on the crank end of the
the outstroke, gas is entering the cylinder on the
cylinder. Suction valve removal is the most
crank end, with the process reversed on the
efficient method of single acting, but does
instroke.
require the unit to be shutdown and gas pressure
removed to change the configuration. Removal

will include the valve, valve seat gasket and Suction valve unloaders are limited to suction
retainer. Washers can be installed on all of the pressures below 1000 psi. Above this level, valve
cap bolts, under the caps, to allow for easier removal or head end bypass unloaders may be
removal of the valve cap for maintenance, and to applied.
indicate that the valve has been removed
Higher pressure forged steel cylinders may Head End Bypass Unloader
require the suction valves to be in place in order
Head end bypass unloaders are pneumatically
for the gas seal at the valve cap to correctly seal.
actuated ports on the head end of the cylinder
If the gas seal is located between the valve cap
that allows the head end compression to be open
and the valve retainer, the valve body must
to the suction gas pressure. This fully deactivates
remain in place. Single acting in this instance can
the head end of the cylinder for single acting
be done by removing the valve plates and
configuration. The pneumatic actuator is
springs, but reinstalling the "empty" suction
smaller, to fit within the unloader, so requires a
valve body in the cylinder. If the valve cap
higher actuation pressure, often in the few to
includes a pressure activated seal assembly, the
several hundred psi level. Each application and
suction valve, seat gasket, and retainer can be
cylinder size will require a specific actuation
removed to single act.
pressure. These can be found in the Ariel
performance software on the device datasheet.
Suction valve Unloader Most often, process gas can be regulated to the
appropriate pressure and applied as the
Suction valve unloaders are typically applied on
actuation gas. Clean, dry actuation gas is
the head end of the cylinder, allowing
required. Sour actuation gas (greater than 100
compression only on the crank end. Ariel requires
ppm H2S) is NOT to be used as the actuation gas.
installing suction valve unloaders on all suction
valves of a cylinder end to be single acted to If the process gas contains hydrogen sulfide,
reduce horsepower losses. nitrogen may be used for the actuation.
In order to maintain proper rod load reversal, the

head end of the cylinder is usually deactivated.
This will help maintain rod load reversal due to
the differential areas between the crank end and
the head end of the cylinder (due to the rod area
in the crank end). In some cases it is possible to
deactivate the crank end and maintain rod load
reversal due to the inertia load.

Tandem cylinders are used to allow two stages of

compression on a single throw. Since they are
two single acting cylinders, flow rates are smaller
than double acting cylinders.
Tandem Cylinder, High Pressure Cylinder
Outboard
Single acting cylinder operating cases should be

included in the analyses for torsional responses
and acoustical pulsation responses. Single
Acting cylinders can present the worst case
Tandem Cylinder, High Pressure Cylinder Inboard
scenario for a torsional analysis due to a more
dynamic torque effort curve and for an acoustical
pulsation analysis due to a change in the number
of pulses per cycle. High torsional vibration and /
or high acoustically driven vibration can result
from single acting cylinder operation when not
considered in these analyses.
Some restrictions may apply to operating a

cylinder single acting at higher speeds. The
performance software should flag higher speed
single acting conditions that require review and Cylinder Hydro Test
approval.
All Compressor cylinders are hydrostatically
tested prior to shipment. The cylinders are tested
Cylinder Action, Tandem at a minimum of 1 hour at 1.5 times the rated
MAWP of the cylinder (Maximum Allowable
Tandem cylinders are two cylinders on the same
Working Pressure). The hydrostatic test pressure
throw. The inboard cylinder may be the high
is recorded on a pressure test recorder vs time
pressure or low pressure cylinder, and is single
and retained with the permanent unit file.
acting on the crank end only. The outboard
cylinder may also be the high pressure or low Cylinder hydrotests may be observed by the
pressure cylinder, and is single acting on the client if required. Requests for witness must be
head end only. included at the time of order for scheduling
purposes.

For lighter gasses, mole weights below 12 or Elevation

hydrogen content above 50%, cylinders will be
leak tested with helium. Once the cylinder has The elevation is the distance of a compressor
been hydrotested , the cylinder is submerged in a above mean sea level. Elevation affects
water tank and pressurized with Helium to the atmospheric pressure and therefore absolute
cylinder MAWP or 2000 psig , whichever is lower. pressure. This becomes important in the
Pressure must be maintained and no leaks performance calculations in the Ariel
observed for a period of thirty (30) minutes. Performance Software. Elevation can change the
Helium leak tests of compressor cylinders is inlet pressure conversion from gauge to absolute
available as an option. by anywhere up to 30%, greatly affecting flow
and power calculations. This is especially true
Helium testing is required for gasses 12 mole with lower suction pressures and higher
weight and below as well as gasses with 50% or elevations.
more hydrogen by volume.
Internal Rod Load, Gas

Discharge Event
Internal Gas Rod Load is the force imposed on the
Discharge event refers to the time interval in rod, caused by pressure inside the cylinder
milliseconds for the discharge valve plates to against the head end and crank end piston areas.
open, stabilize and close. Should this time Ariel's gas rod load equations apply internal
window become too short, higher valve impact cylinder pressure, accounting for pressure losses
velocities will result, and consequently reduced through valves and cylinder passages.
valve reliability.
Ariel uses internal gas rod loads for a compressor
Ariel has set the limit for the discharge event to frame rating. Combined gas and inertia loads are
be 2.7 milliseconds. Discharge event times of not part of the frame rating, but are used for
between 4.5 and 2.7 milliseconds should be determining the crosshead pin load reversal.
reviewed by Ariel Valve Engineering to select
proper valves for the application. Low lift valves For Internal Gas Rod Load equations, please refer
may be necessary in this discharge event range, to the Ariel Calculation Method topic.
decreasing valve impact velocity.
Discharge event values can be increased by Piston Displacement

lowering compressor speed, decreasing the
compression ratio or decreasing cylinder Piston displacement is expressed in cubic feet
clearance. If discharge event values cannot be per minute and is the product of the swept
improved upon, low lift valves may be necessary volume and compressor speed in revolutions per
in order to decrease valve impact velocity. minute. The following formula would be used to
calculate the displacement of a cylinder;

Pressure, Absolute Flange

Pressure Loss Not To Exceed
Pressure
The absolute pressure is the sum of the
35 psia and 5% 1 psi
atmospheric pressure and the gauge pressure. It
below
is abbreviated "psia".
36 psia to 250 3% 5 psi
psia
Pressure, Atmospheric 251 psia to 1000 2% 10 psi
psia
Atmospheric pressure exerted by the earth's
1001 psia and 1%
atmosphere. The normal pressure measured by a above
barometer at sea level is equivalent to a column
of mercury 29.92 inches high or 14.696 psia. Reference Ariel Calculation Method.
The following formula can be used to calculate

the atmospheric pressure for a given elevation: Pressure, Gauge
For elevation greater than 50 feet: Gauge pressure is the pressure above
atmospheric pressure as shown by a pressure
gauge. It is generally expressed in pounds per
For elevation < 50 ft, use Patm = 14.696 psia
square inch and abbreviated "psig".
Pressure Drop Pressure, Rated Discharge

Ariel performance program utilizes inputs for the (RDP)
pressure at the customer line connection, inlet,
and outlet. Pressure drops for suction, ISO-13631 and API-618 define the Rated
interstage, and discharge equipment should be Discharge Pressure as the "highest pressure
considered while defining the pressures in the required to meet the conditions specified by the
performance program. purchaser for the intended service".
Typical suction and discharge pressures are Rated Discharge Pressure is conditional upon the
defined at the customer's line connections. Any Maximum Allowable Working Pressure based on
pulsation vessels, knock out drums or coolers the guidelines in ISO-13631 and API-618. The
should be accounted for in the pressure loss maximum allowable working pressure shall
section of the performance input. exceed the RDP by at least 10% or 25 psi (1.7 bar),
whichever is greater.
The Ariel performance program will assume
average values for these pressure losses for each
interstage and final discharge pressure, as shown
in the table below. These values can be manually
input if known. The first stage suction pressure
loss is initially set at 0 psi, any equipment
upstream of the cylinder flange should be input.

Ariel does allow for operation above the cylinder • Mean Gas Temperature (suction plus
RDP provided there is ample room for the discharge / 2) above 285 F (140 C)
pressure relief valve range and for a high Ariel compressor applications with suction
pressure shutdown device. Typically, when the temperatures below 0 °F (-18°C) should be
operating pressure is above the RDP, a pilot reviewed by Ariel Applications Engineering. Ariel
operated relief valve must be used (rather than a will review these selections to confirm the gas
spring operated relief valve). The relief valve properties.
must be set no higher than the cylinder MAWP.
Ariel does not limit services based upon low
ambient temperatures.
Rod Load, Inertia
Please refer to the Packager Standards Section 6,
Inertia rod load is the force derived from the Lubrication, for frame oil heating requirements
acceleration and deceleration of the mass of the for starting and loading purposes.
reciprocating components; piston and rod
All low suction temperature applications should
assembly and crosshead assembly. The inertia
be reviewed for gas condensates. Refer to Gas
rod load is a direct function of the amount of
Method. High suction temperature and mean gas
reciprocating mass and the square of the rotating
temperature limitations are applied due to
speed. Inertia rod load always reverses.
limitations on the non-metallic wear materials
Inertia rod load is important for calculating within the cylinder.
crosshead pin reversal. Ariel calculates inertia
rod load solely for the purposes of calculating NOTE: There is a potential for o-rings to lose flexibility
crosshead pin reversal. while at lower temperatures, at or below -10 F (-23 C).
This temporary loss of flexibility may result in poten-
tial gas release at the o-ring sealing joints on the cylin-
Separable Compressor ders when under pressure. The lower temperatures
occur with either low inlet gas temperatures during
A separable compressor package has separate operation or low ambient temperatures during idle
crankshafts for the compressor and driver periods. If the gas release is of concern, it is recom-
mended that the unit be allowed to warm up in a rela-
connected with a flexible coupling. The
tively unloaded state (low or no gas pressure and start
compressor must be packaged with a driver, up bypass line fully open) until the equipment
cooler, and associated liquid separation reaches warmer temperatures.
equipment and gas and utility piping.
Suction Temperature Swept Volume

Ariel Compressor Performance Software flags Swept volume is the volume swept by a
suction temperatures at the following levels: compressor piston during a complete stroke.
Swept volume is expressed in cubic inches and
• Low Suction Temperatures below -40 F (-40 C)
calculated as follows:
• High Suction Temperatures above 250 F (121
C) Head End = Area Piston (in2) * Stroke (in)

Crank End = (Area Piston (in2) - Area Rod (in2)) * BOYLE’S LAW states that if the temperature of a
Stroke (in) gas remains constant, its volume varies inversely
with the absolute pressure. It is expressed by the
Total = [2 x Area Piston (in2) - Area Rod (in2) ] *
Stroke (in) formula:
CHARLES’ LAW states that if the pressure of a gas

Thermodynamic Terms remains constant, its volume varies directly with
the absolute temperature. It is expressed by the
Some definitions given here are not as all-
inclusive as general thermodynamics might
require, but cover the ground necessary for formula:
reciprocating compressor applications. There
IDEAL GAS LAW is created by combining Boyle's
are some items where "authorities" differ in
and Charles' Laws. It is expressed by the formula:
definition and approach. In such cases, a certain
amount of judgment has been applied.
SPT means standard pressure and temperature.

As used herein it is 14.696 psia and 60° F in the
English system of units. COMPRESSIBILITY is a volume ratio that
indicates the deviation (as a multiplier) of the
STANDARD Conditions, in the SI System, are actual volume from that as determined by the
1.01325 barA and 15 C. These conditions are used perfect or ideal gas laws. When compressibility is
in Canada, South America, and New Zealand applied, the equation is the real gas law.
NORMAL Conditions, in the SI System, are Compressibility is designated by the term “z”,
1.01325 barA and 0 C. These conditions are used and is a function of pressure, temperature, and
primarily in Europe.
DENSITY is the weight of a given volume of gas, gas composition.

usually expressed in lb/cu.ft. at SPT conditions.
TEMPERATURE is the property of a substance
SPECIFIC VOLUME is the volume of a given that gauges the potential or driving force for the
weight of the gas, usually expressed as cu. ft./lb flow of heat.
at SPT conditions.
ABSOLUTE TEMPERATURE is a temperature
SPECIFIC GRAVITY is the ratio of the molecular measurement relative to an absolute scale. The
weight of a given gas to the molecular weight of absolute scale in English units is degrees
dry air, both measured at the same specified Rankine; Temp Rankine = T F +460. The absolute
conditions of temperature and pressure usually temperature scale in SI units is degrees Kelvin
14.696 psia and 60° F. It should also take into Temp Kelvin = T C +273. Zero degrees in both
account any compressibility deviation from a absolute temperature scales reference the
perfect gas. temperature when a substance contains no heat.

ISOTHERMAL PROCESS is one during which HEAT is energy transferred because of a

there is no change in the temperature. This is temperature difference. There is no transfer of
impractical, as it would require all heat to be mass.
continuously removed from the process.
WORK is energy in transition and is defined as
ISENTROPIC (ADIABATIC) PROCESS is one Force times Distance. Work cannot be done
during which there is no heat added to or unless there is motion.
removed from the system. All the heat of
ENTHALPY (Heat Content) is the sum of the
compression is contained in the gas and shown
Internal and External energies.
as a temperature increase. Although not attained
in practice, adiabatic compression is a good ENTROPY is a measure of the unavailability of
model for most positive displacement energy in a substance.
compression.
SPECIFIC HEAT (Heat Capacity) is the rate of
ADIABATIC HORSEPOWER is the power required change in Enthalpy with temperature. It may be
to adiabatically compress a gas delivered from measured at constant pressure or at constant
one pressure to a higher one. The power is volume. The values are different and are known
calculated at the face of the compressor piston. as cp, and cv respectively. For a perfect gas, Cp=
Cv + R. R is the universal gas constant.
ADIABATIC EFFICIENCY is the ratio of the
adiabatic horsepower required to compress a RATIO OF SPECIFIC HEATS (k) is the ratio of Cp
given amount of gas to the actual horsepower over Cv. It may vary considerably with
expended in the compressor cylinder The temperature and pressure levels.
adiabatic efficiency is dependent upon factors
SATURATED VAPOR PRESSURE is the pressure
such as gas preheat and valve horsepower losses.
existing at a given temperature in a closed vessel
MECHANICAL EFFICIENCY is the measure of the containing a liquid and the vapor from that liquid
power lost due to mechanical friction of the after equilibrium conditions have been reached.
piston rings, packings, and bearings. A value of It is dependent only on temperature and must be
95% mechanical efficiency is used for the determined experimentally.
compressor cylinders in addition to specific
SATURATED PRESSURE is another term for
frame losses that include bearing and oil pump
Saturated Vapor Pressure.
losses.
SATURATED TEMPERATURE is the temperature
BRAKE HORSEPOWER is the measured
corresponding to a given saturated vapor
horsepower input to the compressor. It is the
pressure for a given vapor.
adiabatic horsepower divided by the adiabatic
efficiency and the mechanical efficiency. DEW POINT of a gas is the temperature at which
the vapor (at a given pressure) will start to
POLYTROPIC PROCESS is one in which changes
condense (or form dew). Dew point of a gas
in gas characteristics and properties are allowed
mixture is the temperature at which the highest
for throughout the process.
boiling point constituent will start to condense.

BUBBLE POINTof a gas is the temperature at CRITICAL PRESSURE is the saturation pressure
which the liquid (at a given pressure) will start to at the critical temperature. It is the highest vapor
boil (or form vapor). Bubble point of a gas pressure the liquid can exert. Note: Critical
mixture is the temperature at which the lowest conditions must be experimentally determined
boiling point constituent will start to boil. for each pure gas. When calculated for a mixture,
they are called pseudo critical conditions.
RELATIVE HUMIDITYis the amount of water
Pseudo critical conditions are a mole % (volume
vapor entrained in a gas, expressed as % of
%) weighted average of critical conditions for
saturation.
each constituent of a mixture.
PARTIAL PRESSURE of a constituent in a mixture
REDUCED TEMPERATURE is the ratio in absolute
is the absolute pressure exerted by that portion
units of the actual gas temperature to the critical
of the mixture. Calculated by multiplying the
temperature. Pseudo - reduced temperature is
absolute pressure of the system by the mole
the ratio in absolute units of a gas mixtures
fraction of the constituent in the mixture.
actual temperature to pseudo - critical
DRY GAS is any gas or gas mixture which contains temperature.
no water vapor and also in which all of the
REDUCED PRESSURE is the ratio in absolute
constituents are substantially above their
units of the actual gas pressure to the critical
respective saturated vapor pressures at the
pressure. Pseudo - reduced pressure is the ratio
existing temperature. Note: In commercial
in absolute units of a gas mixtures actual
compressor work a gas may be considered dry
pressure to its pseudo - critical pressure.
(even though it contains water vapor) if its dew
point is low at the inlet condition (say -50° F to -
60° F.) Note: In commercial compressor work a Valve Lift
gas may be considered dry (even though it
contains water vapor) if its dew point is low at the Valve lift is the distance between the top of the
inlet condition (say -50° F to -60° F.) valve plate and the bottom of the valve guard
when the valve plate is seated against the valve
WET GAS is any gas or gas mixture in which one seat. Valve lift effects lift area, and adjusted
or more of the constituents is at or very close to equivalent area. Higher lift valves are more
its saturated vapor pressure. The constituent at efficient (larger equivalent flow areas), but are
saturation pressure may or may not be water not as durable as lower lift valves due to the
vapor. higher impact forces (more time for acceleration
CRITICAL TEMPERATURE is the highest of the valve plate).
temperature at which a gas can be liquefied. The maximum valve lift for metallic valve plates
is 0.063 inches. The maximum valve lift for non-
metallic valve plates (PEEK, Nylon, MT) is 0.112
inches. Non-metallic valve plates are lighter
weight, and therefore do not generate as much
impact force at higher lift as metallic valve plates.

Figure: Valve Cross Section
Valve Velocity
Average valve velocity is calculated as follows:
V = Valve velocity, ft/min
D = Piston displacement, cfm

A = Product of lift and valve opening periphery,
total for all valves in the cylinder
Velocities calculated by this method should be

treated only as a general indication of valve
performance.

Calculations
Interstage flange pressures are determined by
balancing the flow of gas through each stage
(expressed in standard, not actual volume). Gas
Ariel Calculation Method added through side streams or removed through
The Ariel Performance Software includes side streams or condensate from each stage is
calculations for predicting the flow, power, considered.
temperatures, pressures, gas rod loads, Pressures inside the cylinder consider pressure
crosshead pin load reversals as well as other losses through the cylinder gas passages and
values for the predictions and limitations of the valves. Many of the calculations apply the use if
compressor applications. The following outlines internal pressures rather than flange to flange
the general methods and some of the equations pressures. Cylinder and valve pressure losses are
applied for Ariel reciprocating compressors. a function of the gas density and gas velocity
Pressures: through the cylinder gas passages and valves.
Operating pressures are calculated allowing user Temperatures:

input pressure losses prior to, after and between Discharge temperature after each stage of
stages of compression. Ariel includes a typical compression is a function of the gas properties
pressure loss for the interstage and final (k-value, or N-value), internal compression ratio
discharge pressure losses. Typical values are: and suction temperature. Suction temperature
at each stage is user defined. The internal suction
Flange
Pressure
Pressure Loss Not To Exceed temperature may include a preheat value,
depending upon the inlet gas temperature and
35 psia and 5% 1 psi
below discharge gas temperature.
36 psia to 250 3% 5 psi • Discharge Temperature (initial estimate

psia
251 psia to 1000 2% 10 psi using flange ratio):

psia • Suction Temperature Preheat: Tsph = Ts +
1001 psia and 1% [(0.02 + (0.002 x Cyl bore)) x (Tdi - Ts)]
above • Discharge Temperature: Td = Tsph x (Rint-
ernal)^((k-1)/k)
Operating pressures at each stage are expressed
Flow:
in the term Compression Ratio. Depending upon
the use of this term, it may be defined at the
cylinder flange pressures or the internal
pressures. Compression ratio is the discharge
pressure divided by the suction pressure (in
absolute pressure units).

Application Manual – Calculations 12/13/2023
Flow is a function of the piston displacement and Mechanical Efficiency is near 0.95, offering a 5%
the volumetric efficiency. The piston loss for mechanical inefficiencies of the
displacement is the piston area times the length cylinders. Friction power loss is dependent upon
of stroke times the rpm. Both ends of a double the frame size.
acting cylinder are included in this calculations,
Gas Rod Load:
with the crank end considering the loss of piston
area due to the piston rod. Flow is calculated on Ariel calculates gas rod load based upon internal
a per end basis. cylinder pressures. The equations below are
based upon pressures in gauge units. If absolute
units are applied, then additional terms for Patm
being applied on the piston rod diameter must be
As Q is actual flow, it is often converted to be included.
expressed in standard flow units.
Double Acting Cylinders
Volumetric Efficiency: • RLc = Ahe x Pdi - Ace x Psi
Volumetric efficiency includes many factors that • RLt = Ace x Pdi - Ahe x Psi
help explain the differences between ideal gas Single Acting Crank-End Cylinders
behavior and real gas behavior. In general,
• RLc = Ahe x Pdihe - Ace x Psi
volumetric efficiency depends upon
• RLt = Ace x Pdi - Ahe x Psihe
compression ratio, cylinder clearances, gas
compressibility values and the ratio of specific Tandem Cylinders - (High Pressure Cylinder
heats (k or N value). A common representation of Outboard)
volumetric efficiency is:
Power:
Power is calculated through a power per unit

flow equation, multiplied by the flow. Calculated
power will include the power of compression,
plus mechanical inefficiencies, plus frame
• RLc = Ahe(HP) x Pdi(HP) +[Ahe((LP) - Ahe(HP)]
friction power. Internal power of compression x Psflg(LP) - Ace(LP) x Psi(LP)
equations include: • RLt = Ace(LP) x Pdi(LP) - [Ahe(LP) - Ahe(HP)] x
Psflg(LP) - Ahe(HP) x Psi(HP)
Tandem Cylinders - (High Pressure Cylinder
Inboard)
CHP = Q x (IHP/MM)/ Mech Eff + Friction power.

Definitions / Units
Area units are in square inches.
Diameter and stroke units are in inches.
Gas velocity units are in feet per minute
Pressure units are in psia for ratio calculations

and psig for rod load calculations.
Temperature units are in Rankine.

• RLc = Ahe(LP) x Pdi(LP) - [Ahe(LP) - Ahe(HP)] x
Psflg(LP) - Ace(HP) x Psi(HP) Power units are in hp.
• RLt = Ace(HP) x Pdi(HP) + [Ahe(LP) - Ahe(HP)]
x Psflg(LP) - Ahe(LP) x Psi(LP) Flow units are in MMCFD, actual for Q and
standard for Flow.
Since Gas Rod Load is calculated using internal
pressures, the pressure losses through the Clearance values are in percent.
cylinder gas passages and valves must be applied
Pressure loss is expressed in percent.
to the cylinder flange pressures. Pressure losses
are calculated using the gas velocity at the
suction and discharge. Gas velocities are Compressor Theory
calculated based upon the flow areas of the gas
passages and valves. Flow areas are available
through the Performance Software cylinder data
Ideal P-V Diagram
sheets. Given the laws governing and definitions
Psi = Psflg x ((100 - PLs)/100) describing gas behavior, let us look at how they
are applied to a typical reciprocating compressor
Pdi = Pdflg x ((100 + PLd)/100) cycle. One of the preferred tools for analyzing
Rint = Pdi / Psi compressor performance is the Pressure-Volume
(P-V) diagram. The P-V diagram which is to be
discussed here depicts the relationship of the
pressure and volume of the gas within one end of
a cylinder of a reciprocating compressor to the
displacement of the piston. To start with we will
look at an ideal P-V diagram in which there are no
valve losses and the compression is adiabatic.
1. Suction valve opens and gas is drawn into the
cylinder (1 - 2).
2. Suction valve closes and gas compression
begins (2 - 3).
3. Discharge valve opens and the compressed

gas is discharged from the cylinder (3 - 4).

4. Discharge valve closes. Note that a gap is with different clearance volumes superimposed.
shown in this diagram between zero volume The opening positions of the valves change
and the volume at position 4. This represents dramatically. With the higher clearance volume
the clearance volume in the cylinder. As the the volumetric efficiency is considerably lower
piston begins its return stroke, the gas which but so is the horsepower consumption.
remains in this space re-expands ( 4 -
1).
Pd = discharge pressure [psia]
Ps = suction pressure [psia]
CL% = clearance volume in %
k = effective cylinder isentropic exponent

Figure: PV vs Clearance
Effect of Clearance Volume on

Capacity
Gas is trapped in the clearance volume after each
stroke. This volume of gas must be re-expanded
before gas at suction conditions is admitted into
the cylinder to be compressed. Figure: PV vs Clearance Low Ratio
Effect of Clearance Volume

The re-expansion of the gas trapped at the end of
the discharge cycle does not influence the
horsepower losses but has a direct effect on the
volumetric efficiency of the cylinder. Figure:
Effect of Clearance Volume shows two P-V curves

Clearance Volume - Low Ratio Below is a comparison of lift vs. equivalent area
for several valves.
In applications where the compression ratio is
relatively small, the extra clearance volume has a
lesser effect on the volumetric efficiency. The
reason for this is demonstrated in Figure: Effect
of Clearance Volume and Figure PV vs Clearance
Low Ratio. In Figure: PV vs Clearance Low Ratio
an application with a 2.7:1 compression ratio is
shown with clearance volumes of 10% and 50%.
With more clearance volume, the piston must
travel farther in its compression stroke before the
cylinder pressure exceeds the discharge line
pressure enough to open the discharge valve.
The discharge volumetric efficiency (VEd)
decreases and can be reduced to a point
(especially in high-speed machines) where the
compressed gas cannot be discharged quickly
enough and the valve is forced to close late. A
similar reduction in volumetric efficiency, and
therefore incapacity, can be expected on the
suction valve when the clearance volume is
increased.
Adjusted Equivalent Valve Area

Adjusted equivalent valve area is a measure of
the effective orifice area of the complete valve Piston Rod Root Stress
assembly. The equivalent area is a static measure
Piston rod root stress is used to design the
and does not assure good dynamic behavior of
appropriate piston rod attachment preload
the valve. This is a useful term to compare valve
levels. Ariel piston rod to crosshead nut preload
designs, as a valve with a higher adjusted
levels are 30,000 psi. This is well above 1-1/2
equivalent area will generally have a lower
times the root stress potential from inertia and
pressure drop and better efficiency.
gas loading. Ariel does not publish a limit based
Equivalent area is a function of valve lift and port upon piston rod root stress.
area. Increasing lift or port area increases
Root areas for Ariel frames are below:
equivalent area. However, higher lift valves
generally have a shorter life than lower lift valves-
-thus the trade-off between efficiency and
durability

Frame Model Rod Diameter (in) Crosshead Thread Pitch Thread Root Area (in2)
JGM:N:P:Q 1-1/8 inch 1"-12 0.625 in2

JG / JGA 1-1/8 inch 1"-12 0.625 in2
JGW:R:J 1-1/2 inch 1-3/8"-12 1.260 in2
JGH:E:K:T KBK:T 2 inch 1-3/4"-12 2.120 in2
JGC:D:F 2-1/2 inch 2-1/4"-8 3.420 in2
KBZ:U 2-7/8 inch 2-5/8"-8 4.76 in2
KBB:V 3-1/8 inch 2-7/8"-8 5.780 in2
Unit Conversions -Flow

Multiply units in left column by proper factor
below.
Units of Flow MMSCFD Sm^3/hr Nm^3/hr
1 MMSCFD @14.7 psia & 60oF 1 1179.87 1116.28
1 Sm^3/hr @1.0135 BarA & 0.0008476 1 0.9461

15oC
1 Nm^3/hr @1.0135 BarA & 0oC 0.0008958 1.0569 1
Flow Units: CFM -Cubic feet per minute. Sm3/hr -Standard cubic meters per hour,
ACFM -Actual cubic feet per minute (pressure and measured at standard metric conditions( 1 Atm &
temperature condition must also be stated) 15 °C). Used primarily in Canada, South America,
and New Zealand
ICFM -Inlet cubic feet per minute based upon the
inlet pressure and temperature at the cylinder Nm3/hr -Normal cubic meters per hour,
flange. measured at normal metric conditions (1 Atm & 0
°C). Used primarily in Europe.
SCFM -Standard cubic feet per minute is gas flow
measured at standard conditions (14.7 psia & 60
°F). Unit Conversions - Volume
MMSCFD -Million standard cubic feet per day is Multiply units in left column by proper factor
million cubic feet of gas per day measured at below.
standard conditions (14.7 psia & 60 °F). (not to be
confused with MSCFD, 1000 SCFD)

Units of Volume cu.in. cu.ft. cu.meter liter US.gal Imp. gal
1 cu.inch 1 0.00058 0.0000164 0.0164 0.0043 0.0036
1 cu.foot 1728 1 0.0283 28.32 7.481 6.229
1 cu.meter 61,023 35.31 1 1000 264.2 220
1 liter 61.025 0.0353 0.0010 1 0.2642 0.220
1 US. gal 231 0.1337 0.0038 3.785 1 0.8327
1 Imp. gal 277.4 0.1605 0.0045 4.546 1.201 1
Unit Conversions - Power

below.
Units of Power hp kw
1 horsepower 1 0.7457
1 kilowatt 1.3410 1
Unit Conversions - Pressure

below.
Units of Pressure psi atm kg/sq.cm. kPa bar
1 pound/sq.in. 1 0.06805 0.0703 6.89476 0.06895
1 atmosphere 14.696 1 1.0332 101.325 1.01325
1 kilogram/sq. cm. 14.223 0.9678 1 98.066 0.98066
1 kilopascal 0.14504 0.009869 0.010197 1 0.01
1 bar 14.504 0.9869 1.0197 100 1
Unit Conversions - Length

below.

Units of Length in ft mm cm m
1 inch 1 0.0833 25.4 2.54 0.0254
1 foot 12 1 304.8 30.48 0.3048
1 millimeter 0.394 0.00328 1 0.1 0.001
1 centimeter 0.3937 0.03281 10 1 0.01
1 meter 39.37 3.281 1000 100 1
Unit Conversions - Weight

below.
Units of Weight lbs ton kg metric ton
1 pound 1 0.0005 0.4535 0.00045
1 ton 2000 1 907 0.907
1 kilogram 2.205 0.0011 1 0.001
1 metric ton 2205 1.102 1000 1

Compressor
A compressor is the combination of a frame and Connecting Rods
cylinders. A complete compressor is provided
with a properly sized cylinder lube distribution Ariel Connecting Rods are machined from forged
system and balance components. steel in all frames except for JGM,JGP, and JGH,
which are made of ductile iron.
Frame
The main components of a compressor frame
include the base casting, crankshaft, connecting
rods, crossheads, and crosshead guides. An
example of a four throw Ariel frame would be a
JGK/4.
Crossheads
Crankshafts Ariel uses one piece crossheads with full top and
bottom lubrication. Crossheads are ductile iron
with babbitted sliding surfaces, except for the
JGM and JGP which are gray iron without
babbitted surfaces. Heavier crossheads, used to
balance larger opposing weights, can be
provided in bronze.
Ariel two throw and four throw Compressor

frames utilize integral counterweights to
minimize horizontal couples.
Ariel two throw and four throw Compressor Full floating alloy steel crosshead pins are used in
frames utilize integral counterweights to Ariel frames; all frames except for the JGM, JGP,
minimize horizontal couples. and JGH have bronze crosshead pin bushings.
Ariel Crankshafts are precision machined of Inadequate rod load reversal can result in lack of
forged steel with a keyless shaft end. lubrication to the crosshead pin and consequent
JGE/6, JGK/6, JGT/6, KBB, and KBV frames have failure.
integral flanged crankshafts. Crossheads and crosshead nuts of varying weight
are available to facilitate proper frame balance.
Balance crossheads are available to balance
opposite blank throws.

Application Manual – Compressor 12/13/2023
Frame Lube Oil System Aux End Pump Removal

For frame oil system lubricants, viscosities, Both the frame oil pump and the cylinder force
temperatures, and recommendations refer to the feed lubricator pump(s) are located on the
Ariel Packager Standards Section 6.0. auxiliary end of the compressor frame. These
may be removed, and electric motor driven, for
various reasons.
Frame Driven Lube Oil Pumps
Ariel offers an electric motor driven cylinder force
The frame lube oil pump is driven by the chain
feed lubricator pumps in place of the chain
drive system at the auxiliary end of the frame.
driven cylinder force feed lubricator pumps. This
The lube oil pump sprocket and the crankshaft
option is for two purposes; for customer
sprocket are sized so that the pump is running at
preference and for torsional considerations at
the correct speed when the frame is running at
the auxiliary end of the compressor.
rated speed.
If this is for a torsional consideration, both the
Oil pump discharge pressure is held nearly
cylinder force feed lubricator pump and the
constant by a spring loaded regulating valve
frame oil pump must be removed from the
within the pump head. Lube system pressure can
auxiliary end.
be raised or lowered by adjusting this valve.
Normal pressure on the discharge side of the lube Some frames utilize a single chain for both the
oil filter is set at the factory at 60 PSI when the cylinder force feed lubricator pumps and the
crankshaft speed is greater than half rated speed. frame oil pump. Larger frames utilize a dual
If oil pressure drops below 50 PSI, the reason chain, one for each pump system. When the
should be found. electric motor drive cylinder force feed lubricator
pump option is purchased and the frame uses a
The larger frames, KBU:Z and KBB:V, utilize an
single chain system, a fully functional lube box,
external pressure relief valve located
without lubricator pumps, will remain as a chain
downstream of the lube oil filter. The external
idler where the cylinder force feed lubricator
pressure relief valve is used to set the system
pumps were located.
pressure. The regulating valve located on the
main lube oil pump is to be set fully closed.
If the crankshaft speed is less than 50%, there will

not be enough flow through the pump to
maintain proper lube oil pressure to the frame -
an auxiliary lube oil pump will be needed.
The frame oil pump may require removal due to

torsional vibration concerns. Please refer to the
Auxiliary End Pump Removal topic for further
information.

Single Chain Drive

Chain
Frame Throws
Configuration
JG, All Single

JGM:N:P:Q:A:R:J
JGH:E:K:T 2,4 Single
JGE:K:T 6 Dual
JGC:D:F 2,4 Single
JGC:D:F 6 Dual
KBZ:U:B:V, All Dual

JGZ:U:B:V
Ariel offers an option for Pumps Removed, No

Chain Drive System. This option is for both
customer preference and for torsional
considerations. If the chain drive system is
removed from the auxiliary end of the
Dual Chain Drive compressor, the electric motor driven cylinder
force feed lubricator pump option must be
purchased. The frame oil pump will be removed
along with the chain system and will not be
provided (packager must provide electric driven
frame oil pump assembly).
Operation below half of the frame max rated

speed does not require a separately driven
cylinder force feed lubricator pump. When the
compressor speed is reduced, the cylinder
lubrication demand reduces and matches the
cylinder force feed lubricator pump supply at the
reduced speeds. Operation below half of the
frame max rated speed does require additional
frame oil supply flow, through a separate
auxiliary frame oil pump, provided by the
Packager.
When the cylinder force feed lubricator pumps

are electric motor driven and the compressor is
driven by a VFD motor, consideration should be
given to operating the electric motor driven
cylinder force feed lubricator with a VFD. The
cylinder lubrication demand varies directly with
the operating speed of the compressor.

Pumps can be removed during packaging or after The KBU:Z/2, JGC:D:F:KBZ:U:B:V/4 and
field installation if necessary. Ariel offers blind JGE:K:T:C:D:F:KBZ:U:B:V/6 frames are equipped
cover plates for the different pump locations. For with a simplex, cartridge style, pleated paper
a single chain system, both the cylinder force type filters. The nominal filtration is 1 micron.
feed lubricator pump and frame oil pump must The filter housings are equipped with pressure
be removed as idler sprockets are not available. gauges to determine pressure drop across the
filter. Ariel recommends replacing the filter
element when the differential pressure across
Pre-lube Requirements
the filter reaches 15 psid at normal temperatures
Ariel offers a manual lube oil priming pump for or at six month intervals (or 4000 hours,
the JGI, JGM, JGP, JGN, JG, JGQ, and JGA frames whichever comes first).
(unmounted) as an option and the JGW, JGR,
Duplex lube oil filters with continuous flow
JGJ, JGH, JGE, JGK, and JGT frames (mounted)
transfer valves can be provided as an option.
as an option.
Duplex filters are to be mounted separately (not
JGC, JGD, JGF, KBZ, KBU, KBB, and KBV frames directly attached to the frame by Ariel), the
must be equipped with a motor driven pre-lube original simplex filter must remain on the frame,
pump. A priming pump is not provided by Ariel operating in series downstream of the duplex
for these frames. filter. Duplex filter nominal filtration levels will
match the frame mounted simplex filters noted
Refer to Section 6 of the Packager Standards for
above (5 micron on the smaller frames and 1
information regarding the sizing of the pre-lube
micron on the larger frames)
pump.
Lube Oil Cooler

Lube Oil Filter
Each lube oil system must be equipped with a
All Ariel frames require full flow filtration.
lube oil cooler to maintain the proper
All Ariel frames with exception of KBU:Z/2, temperature of the lube oil before it is supplied to
JGC:D:F:Z:U:KBB:V/4 and the bearings. Maximum allowable oil
JGE:K:T:C:D:F:KBZ:U:B:V/6 are equipped with temperature to the frame is 190°F (88°C).
simplex, spin-on, pleated paper type filters. Thermostat temperature should be set at 170°F
These spin on filters have a nominal filtration of (77°C). The cooler should be as close as possible
5 micron. The filter headers are equipped with to the compressor, and the piping of adequate
pressure gauges to determine pressure drop size to minimize pressure drop below 10 psi.
across the filter. Ariel recommends replacing the
Ariel offers an unmounted shell and tube lube oil
filter element when the differential pressure
cooler as an option. Based on 140 deg F water in
across the filter reaches 10 psid at normal
the tube side at a 2:1 oil to water flow ratio the
temperatures or at six month intervals (or 4000
following coolers can be used. Contact
hours, whichever comes first).
Application Engineering for specific cooler
applications. Less available water flow may
require a larger cooler than specified.

Warmer ambient temperatures, and within Maximum Allowable Lube Oil

enclosed engine rooms, may require a larger Temperature
cooler to help dissipate the heat load. The
compressor frame can account for up to one half The frame lube oil system is designed for a
of the heat transfer when installed in an open maximum allowable lube oil temperature of 190
environment. The coolers specified below are F, with a required thermostat setting of 170 F.
based on an open environment. These temperatures are based upon the viscosity
needs as outlined in the Ariel Packager Standards
When the coolers are provided by others, heat
Section 6 Lubrication. Refer to this section for
load data can be found in the Ariel DataBook or
lube oil viscosity chart for some of the common
Ariel Performance Program. The heat load
lube oil grades to determine suitability for the
numbers are based on an open field
compressor frame oil system.
environment. Shell and tube, radiator style (oil to
air) and plate and frame lube oil cooler types are
acceptable. Minimum Allowable Lube Oil
Temperature
Frame Cooler
The frame oil temperature must meet a specific
JG:A:M:N:P:Q:R:J/2/4,JGH single pass cooler (P/N B-
:E:K:T/2, KBE:K:T/2 1962) minimum prior to starting the compressor. As
well, it must meet a specific minimum
JGJ/6, JGH:E:K:T/4, single pass cooler (P/N B-
JGC:D:F/2/4/6, JGE:K:T/6, 2073) temperature prior to loading the compressor.
KBE/4,KBK:T/4/6, KBU:Z/2 These temperatures are based upon the oil
KBU:Z/4/6, KBB:V/4/6 two pass cooler (P/N B- viscosity since there are some differences in
6250) similar weight oils that may be suitable for the
frame oil system. See the Ariel Packager
Ariel cooler material specifications: Standards Section 6, Compressor Frame
Lubricants, for viscosity and temperature
Shell Steel
information.
Baffles Steel
Mounting Brackets Steel

Dry Sump
Gaskets Nitrile Rubber / Cellulose
Fiber Units that are installed on board ships or floating
Tubes Copper production platforms may require the dry sump
option. This option would be required if the roll
Fins Aluminum
and yaw of the ship would cause the frame lube
End Caps Gray Iron oil pump to lose suction of the oil in the sump or
Nameplate Aluminum any of the running gear to foam the oil from
Oil in the Shell side Water in the tubeside contact with the oil level. Refer to Frame Tilt
Limits for Offshore for allowable tilt with a wet
sump in offshore applications.

If the dry sump is selected, both frame ends are Short Single Compartment Distance
supplied with drains and an additional oil pump Piece
chain oiler is provided. An oil sump strainer is
provided by Ariel to be placed in the pump A short coupled distance piece, described by ISO-
suction line at the outlet of the Packager's wet 13631 as Type 1, is used when mixing of the
sump. The packager is responsible to provide a cylinder lubricant and the crankcase lubricant is
lube oil reservoir sized and located such that the acceptable. Since oil and process gas will enter
oil pump will have suction regardless of the tilt of the crankcase from along the piston rod, the
the ship or floating platform. short, single compartment distance piece is
recommended for use when compressing non-
Refer to the Packager Standards Section 6: corrosive gasses. This distance piece will also
Lubrication for further information and keep the package arrangement at minimum
schematics. width.
Maximum Frame Tilt for Offshore

Applications
Units that are installed on board ships or floating
production platforms may require the use of a
dry sump design. This option would be required if
the pitch and roll of the ship would cause either
the crankshaft counterweights or connecting
rods to contact the oil level and froth the oil.
Excessive tilt can also cause the oil pick-up tube
to lose suction. Serious bearing damage can
result from such conditions. The short coupled distance piece is standard for
Leveling Limits for Stationary Reciprocating the JGI, JGM, JGN, JGP, JGQ, JG, JGA, JGW, JGR
Compressors in the Packager Standards Manual and JGJ frames.
lists the maximum angle from horizontal that
each frame can tolerate assuming the motion is Long Single Compartment Distance
transient like the rocking of a boat. There are two Piece
lists, applying to stationary installations and The long single compartment distance piece
transient installations. meets API-618 Type B and ISO-13631 Type 2. It is
used for separation of the pressure and wiper
Distance Piece Arrangements packings. With the availability of the two
compartment distance piece options, the single
compartment distance piece is recommended
for non-corrosive gas applications.

The long single compartment distance piece is

standard on the JGH, JGE, JGT, JGK, KBE, KBK,
KBT, JGC, JGD, JGF, KBZ, KBU, KBB and KBV
frames.
The short, two compartment distance piece is

available as an option on the JG, JGA, JGW, JGR,
JGJ, JGH, JGE, JGT, JGK, JGC, JGD and JGF
frames, and not available on the KBE, KBK, KBT,
KBU, KBZ, KBB and KBV frames.
Short Two Compartment Distance Piece
The short two compartment distance piece may
The short, two compartment distance piece is not be available on all -VS forged steel cylinders.
recommended for use in corrosive applications, Please refer to the performance program for
in order to keep sour or corrosive gasses from availability of the short two compartment
entering the crankcase. It is a modified long distance piece.
single compartment distance piece. The inboard
compartment is suitable for the application of a Refer to the Distance Piece Purge and Vent
purge or buffer gas to maintain a positive Arrangements for notes on a purge system for
pressure on the distance piece. This will assist sour gas.
keeping corrosive process gasses out of the
crankcase. Ariel recommends either sweet Long Two Compartment Distance Piece
natural gas or nitrogen for purge gas, and the (Ariel Design)
distance piece vents must be piped to a safe area. The 8-7/8W:R cylinder long two compartment
distance piece option has a long and a short
distance piece, API-618 Type D and ISO-13631
Type 3. The remainder of the Ariel products use a
Type C long two compartment distance piece.
Ariel recommends either sweet natural gas or
nitrogen for purge gas. The distance piece vents
must also be piped to a safe area. No part of the
piston rod alternately enters the wiper packing
and the intermediate seal packing. This distance
piece is recommended for use when
compressing corrosive gasses.

This long two compartment distance piece is Figure: Long Two Compartment Distance Piece
available as an option on all JGR assemblies (API 618 Type C, ISO-13631 Type 3)
(with R cylinders), and on JGW assemblies with 8
7/8” W Class or any R Class cylinder(s).
Figure: Long Two Compartment Distance Piece
JGR:W (Type D)
Long Two Compartment Distance Piece

(API 618 Type C, API 11P Type 3 Refer to the Distance Piece Purge and Vent
The long two compartment distance piece Arrangements for notes on a purge system for
option meets API 618 Type C and ISO-13631 Type sour gas.
3. There are two long compartments, and each of
the three seal sets can be purged (pressure Balance Crossheads
packing, intermediate and wiper seals). This
distance piece option provides the maximum Balance crossheads are used to balance a blank
amount of protection against flammable, throw, when standard crossheads and balance
hazardous, toxic and corrosive gasses entering nuts are not of sufficient weight; this generally
the crankcase. Ariel recommends either sweet happens when the blank throw is opposite from
natural gas or nitrogen for purge gas. The a larger cylinder.
distance piece vents must be piped to a safe area. When a balancing crosshead is used a special
No part of the piston rod alternately enters the balance crosshead guide is also required due to
wiper packing, intermediate partition packing, or the extra length of a balance crosshead. The
pressure packing. When the purged packing balance crosshead guide cannot accommodate
option is selected the intermediate, wiper and mounting a cylinder. Conversion to blank a throw
pressure packing are arranged for purge. or add a cylinder to an already blank throw will
The long two compartment distance piece is require a new crosshead guide when balancing
available as an option on all JG, JGA, JGJ, JGH, guides are involved.
JGE, JGT, JGK, KBT, KBK, JGC, JGD, JGF, KBZ,
KBU, KBB and KBV frames. Crankcase Relief Doors
Crankcase over-pressure relief valves are
available for all Ariel reciprocating compressors.

Crankcase overpressure relief valves include an The JG:A/2 and JGM:P:N:Q fan shafts connect to
internal flame trap and an external downward the crankshaft with a threaded connection. To
deflector. They are designed to immediately re- avoid the threaded fan shaft from backing out
seal to prevent air from rushing back into the due to shutdown deceleration, the fan inertia
crankcase after an uncontrolled expansion of the must be limited.
gas in the crankcase. When using multiple valves
on a frame, use valves of the same manufacturer, Fan Drive
Frame Horsepower Fan Inertia (Max)
design valve area, and relief pressure. (Max)
Crankcase relief doors are mandatory in Air
JGM:P:N:Q 15 hp 28 lb-ft2 (4000 lb-
Service when short coupled distance piece in2) (1.18 kg-m2)
configurations are applied. This includes the
JG:A/2 15 hp 28 lb-ft2 (4000 lb-
standard guide configuration on the JGM:N:P:Q:I, in2) (1.18 kg-m2)
JG:A and JGR:J:W frames. This is due to the
JG:A/4 15 hp
higher potential for crankcase over-pressure
conditions due to possible auto ignition of JGJ/2 30 hp
lubricants the cylinder, creating escaping gas JGJ/4 50 hp
pressure through the pressure packing.
Figure: Fan Drive Shaft Drive End
Ariel offers crankcase relief doors sized per ISO-
13631 and API-618.
Frame Lube Oil Heaters

Fan Shaft
Up to two (2) bayonet style immersion heaters
Ariel can provide a fan drive shaft on the auxiliary can be installed in Ariel frames. The installation
end of the smaller compressor frames. The fan dimensions for the heaters are contained in the
drive shaft is to be used without a side load. The frame outline drawing notes.
shaft should be supported with an outboard
bearing pillow block pair if used with a side The watt density of the oil heaters must be low
loading similar to a belt drive load. The fan drive enough to avoid “coking” the crankcase oil, 15
shaft can be used up to the power limitations watts per square inch maximum. The oil heater
listed below. should be interlocked with the compressor
instrumentation panel to function only when an
The JGJ/2 shaft will require a pillow block oil circulation pump is operating. Refer to the
arrangement for all applications to limit the axial Ariel Packager Standards Section 6.0 for
thrust on the frame bearings. recommendations on heater watt density.

Thermostatic Temperature Valve Cylinder, Design Features

Each lube oil system should be equipped with a Ariel cast cylinders are single and double wall
temperature control valve to regulate the oil castings. Materials include nodular iron for the
temperature into the frame. The valve should be greater majority of cylinders, cast iron for a very
installed in the “mixing” mode. few of the smaller models and forged steel for the
higher pressure ratings. The cylinders on the mid
A thermostatic valve with a cast iron housing is
and larger frame classes are ion nitrided to
available as an option for all units. The standard
harden the bore for wear resistance. The case
temperature setting of the valve is 170 °F. Valves
cylinders on the smaller frame classes are made
can be provided mounted or unmounted.
from 80-55-06 ductile iron for the harder surface
Information on particular thermostatic valves for wear resistance.
can be found within the Ariel website under
Vendor Literature. Valve sizing for the various Water Jackets
frames is:
• 3/4" NPT Valve - JGM through JGR, JGJ/2-4,
JGH/2, JGE/2, JGK/2, JGT/2 Ariel cylinders are provided without water
• 1-1/2" NPT Valve - JGJ/6, JGH/4, JGE/4, jackets. Water jackets were originally used to
JGK/4, JGT/4, JGC/2, JGD/2, JGF/2 maintain the dimensions of cylinder bores with
• 2"-125# Flanged Valve - JGE/6, JGK/6, JGT/6, longer piston strokes and more complicated
JGC/4-6, JGD/4-6, JGF/4-6 casting geometry. Shorter stroke cylinder
• 3"-125# Flanged Valve - KBZ/2-4-6, KBU/2-4- designs combined with casting quality allow the
6, KBB/4-6, KBV/4-6 use of non-jacketed cylinders while maintaining
stable bore geometry. Despite the
Cylinder misconception, water coursing through the
cylinder passages does not have an appreciable
The main components of a cylinder include the effect on the bore temperature and does not
cylinder body, head end head, crank end head, impact wearing component life.
piston rod, piston, packing, suction and
discharge valves, valve retainers and valve caps.
Cylinders can be double acting or two single
acting cylinders can be combined to create a
tandem cylinder. An example of a double acting
cylinder is an 11K and an example of a tandem
cylinder is a 9-5/8K-CE x 5-3/8K-HE-FS.

Figure: Ariel Cylinder Cross-Section Division 1 of the ASME Pressure Vessel Code
provides consistent design and pressure rating
methods. Please contact Ariel Design
Engineering for a description of the methods
applied.
Cylinder Re-Bore Capability

Ariel cylinders may be rebored within limits. A
bore restoration guideline is available from Ariel
upon request.
Cylinder, Design Options

Cylinder, Design Options
There are several features and options across the

Cylinder Liners cylinder line. These include features such as
number of cylinder lubrication points, piston rod
All ASTM A395 ductile iron cylinder bores are material, piston rod hardening process, wear
surface hardened with an ion-nitride process to bands versus rider rings, cylinder bore hardening
increase cylinder bore wear resistance. Ion through ion-nitride process... A full list of the
nitride surface hardening is provided in lieu of features that are provided, and options that are
providing a sacrificial wear part (liner). Should a available, can be found through the Ariel
cylinder bore become damaged beyond the re- Performance Software.
bore capability, a replacement can be provided.
Since Ariel cylinders are non-jacketed (simpler
casting geometry), the downtime and cost of a Piston Rods
replacement cylinder is generally lower than the Piston rods are designed to resist the loading due
downtime and cost of removal and re- to gas and inertia rod loads and wear in the
installation of a cylinder liner. packing travel area. All Ariel piston rods have
rolled threads to take advantage of the cold
ASME Section VIII Pressure Vessel working and reduce the stress concentration of
Design cut threads. The rods are designed with an
Ariel cast cylinders are designed and pressure undercut, or "fail safe" section. It is intended that
rated based on guidelines from Section VIII, a failure of the piston rod would fail in this
Division 1, of the ASME Pressure Vessel Code. section. A failure at this point allows the piston
Although compressor cylinders categorically rod to be supported by the rod packing, and
cannot be ASME Code stamped, Section VIIl, prevents the escape of gas from the compressor
cylinder in to the distance piece/crosshead
guide, preventing further damage.

Piston Rings, Piston/Rider Rings &

Wear Bands
The piston rod material is ETD 150 or 4150 and is

Ion-nitrided in the packing travel area. Ion
nitride results in a surface hardness range of 57 to
63 Rc from the surface to a base material
hardness of 29 Rc at a depth of 0.008 inches. Water Cooled Packings
Tungsten carbide coating can be provided as an
option. Figure: Packing Cooling Application Guidelines
Gases that contain significant amounts of H2S or

CO2 will require piston rods machined from 17-
4PH stainless steel material to reduce the
potential for corrosion, due to the creation of
sulfuric or carbonic acids. Piston rods of 17-4PH
(UNS S17400) are provided in the double H1150
condition with a base hardness of 33 Rc
maximum and chromium nitrided in the packing
travel area. Chromium nitride provides a surface
hardness of 2500 Vickers. The chromium nitride Cooled packing cases are required for
process has a length limitation due to compressor cylinders based upon the average
manufacturing constraints. Longer stainless piston speed and average cylinder pressure.
steel piston rods will be tungsten carbide coated. Cooled packing cases are supplied to help
(When the length of the stainless steel piston rod remove the heat generated as the piston rod/
requires the tungsten carbide coating, the packing friction increases with the higher
performance software will automatically select pressures and piston speed.
the coating.) Please refer to the Packager Standards Section 7:
Ariel piston rods have a surface finish of 7-13 Cooled Packing for further information on this
micro inches Ra for ion nitride and chromium topic. The following chart is an excerpt from the
nitride hardening processes, and 5-10 micro Cooled Packing topic:
inches Ra for tungsten carbide surface
hardening.

Notes:
1. The Ariel Performance Software will indicate
when operating conditions fall within Region
2 or Region 3.
2. All forged steel cylinders have cooled packing
as standard and must be connected to a
cooling system.
3. All non lubricated cylinders have cooled

packing as standard and must be connected
to a cooling system.
4. Any deviation from the packing cooling

requirements must be reviewed and
approved by Ariel Applications Engineering
Purged Packings
or Technical Services. Purge packing refers to a packing case modified
Cooling with oil is not as effective due to the to accept an external purge pressure 15 to 20 psi
lower heat transfer ability and higher pressure above the primary packing vent/drain pressure
losses due to viscosity. In some circumstances, with no more than 5 psi external system back
oil can be used as a coolant in the packing cases. pressure. The purge gas must be sweet natural
This is limited to lower heat load conditions and gas or an inert gas, such as nitrogen. The purpose
smaller compressor frames. The advantage of of purge gas is to block and contain hazardous,
applying oil cooling in the smaller frames, is the toxic, flammable or corrosive gases, and to
ability to use frame oil, making it possible to cool prevent such from entering the compressor
the packing case with the short coupled distance frame where damage to the running gear, or
piece. Oil will be taken from the frame oil system, personnel safety hazards can occur.
and returned internally, directly into the Figure: Compressor Rod Pack 3500-2000 PSIG with
crosshead guide. Purge Two Compartment Guides
If one packing case is oil cooled on the smaller

frames, the oil will be taken from the pressurized
frame oil system. This is a closed loop and all
tubing provided by Ariel. If more than one
packing is oil cooled, a separate oil loop will need
to be provided by the packager. Oil can be taken
from the sump at the drive end of the frame,
through a pump, cooler, and into the packing. Packing case materials are cast iron and steel.
The packing return will be internal, directly into When steel is used, it is heat treated to be in
the crosshead guide. Below is a schematic compliance with NACE. Garter springs are 316
showing oil cooling on more than one packing stainless steel, for both sweet and sour
case. applications (acceptable for sour service based
upon acceptable field experience).

Please refer to the Packager Standards Section 8 Cylinder Lube Oil Supply
Packing and Distance Piece Vent Systems for
further information on this topic. Cylinder and packing lube oil is normally
supplied from the frame lubrication system at
the main oil gallery directly to the suction side of
Compressor Cylinder Lube Oil the cylinder force feed lubricator pump. The oil
System is then pumped through a distribution block
system to individual supply points; cylinder lube
Ariel provides a distribution block cylinder
injection, packing lube, intermediate packing
lubrication system. A distribution block system
lube, and cylinder flushing points. A lubricator
has a single plunger style pump feeding high
no-flow switch is installed at each primary
pressure oil to a distribution block where a
divider block to ensure appropriate and
combination of specifically sized lube blocks
monitored oil flow.
distribute the oil to the individual lube ports,
such as cylinder lube ports, packing lubrication,
intermediate packing lubrication and flushing
lube ports. Some systems require two pumps to
be manifolded to a distribution block for higher
feed rates. Some distribution block systems
require a two tier system, a primary block that
divides the oil flow for each cylinder and a
secondary block that divides the oil flow for each
lube port. A no-flow instrument is located on
each primary block to allow a measurement of
the lube oil flow (through cycle time) and to
ensure a low oil flow shutdown can be provided.
The advantages of the distribution block system

over single pump per point systems is the ability
to ensure lubrication is provided to all lube
points. If one lubrication point is blocked, the no-
flow device will trigger a shutdown. Precise
lubrication distribution for each point is also
ensured.
Cylinder bore and packing oil lubricants and

rates, refer to the Ariel Packager Standards
Section 6.

Figure: Force Feed Lubrication System Common Oil Supply

1 Frame Oil Gallery
2 Single Ball Check Valve
3 Sintered Bronze Filter (if
applicable)
4 Force Feed Lubricator Pump
5 ARV or Rupture Disk
6 Pressure Gauge
7 Divider Valves/Distribution
Block
8 Fluid Flow Monitor No-Flow
Timer Shutdown Switch
9 Double Ball Check Valve
10 Top Cylinder Injection Point
11 Bottom Cylinder Injection
Point
12 Packing Injection Point
The cylinder and packing lube can be supplied positive pressure. Oil filter and piping pressure
from a separate system. Generally, separate lube drop as well as the increased oil viscosity at cold
oil for the cylinders and packings is required for temperatures should be considered when sizing
applications where the required cylinder and the piping between the day tank and the
packing lubricant is not compatible with the compressor.
frame lubricant. These applications include high
An electric motor driven cylinder force feed
discharge pressure applications , or when the
lubricator is available upon request. Please refer
process gas conditions require an oil heavier
to the Auxiliary End Pump Removal topic for
than 40 weight, or a synthetic lubricant, such as
further information.
when heavy hydrocarbons, wet gas or CO2 are
present in the gas stream and would dilute a See section 6 of the Packager Standards for
conventional lubricant. information on cylinder and packing lubricants
and rates.
For applications requiring separate frame and
cylinder/packing lubricant, the packager is
required to provide a separate day tank for the
cylinder and packing lubricant. A line filter is
recommended between the day tank and the
pump inlet. This day tank will need to be elevated
to provide the cylinder lube pump oil at a slight

Force Feed Lubricator Pump Cylinder, Lube Oil Distribution

The force feed lubricator provides oil to the
Block System
cylinder bore for the piston rings and packing The cylinder lube oil distribution blocks system is
case for the piston rod packing seal rings. The a series of hydraulic divider valves that distribute
lubricator plates provides direction for adjusting lube oil to the various lube points (cylinder bores,
the flow of oil. If the plate is missing, please packings, wiper / seal sets). The system is
contact the Ariel Response Center and a applied with predefined divider valves sized to
replacement one can be provided. offer various rates of lube flow. Once these
blocks are applied to each specific compression
application the oil flow proportions insured
proper lubrication to each lube point.
NOTE: The force feed lubricator box contains approx-

imately 1/3 gallons of lubricant. An initial charge to
the sight glass must be provided prior to initial start
up.

Table: Force Feed Lubrication System Common Oil Supply

1 Frame Oil Gallery
2 Single Ball Check Valve
3 Sintered Bronze Filter (if
applicable)
4 Force Feed Lubricator Pump
5 ARV or Rupture Disk
6 Pressure Gauge
7 Divider Valves/Distribution
Block
8 Fluid Flow Monitor No-Flow
Timer Shutdown Switch
9 Double Ball Check Valve
10 Top Cylinder Injection Point
11 Bottom Cylinder Injection
Point
12 Packing Injection Point
The advantages of the distribution block system Cylinder lubricator no-flow Switch
over single pump per point systems is the ability
to ensure lubrication is provided to all lube The cylinder lubricator no-flow switch monitors
points. If one lubrication point is blocked, the no- the cycling of the cylinder lube oil distribution
flow device will trigger a shutdown. Precise block. A magnet in the lubricator no-flow switch
lubrication distribution for each point is also monitors the position of a piston in the cylinder
ensured. lubricant distribution block. If the piston fails to
cycle in a predetermined amount of time,
Given the nature of the distribution block system indicating a loss of lubrication, the lubricator no-
to provide a specified quantity of oil per each flow switch will send a signal to the control logic
stroke of the divider valve the oil provided to of the package to shut down.
each point can be monitored by one lubricator
no-flow switch per distribution block. In this way There are several lubricator no-flow switch
all points can be insured appropriate and models available. These are listed within the
monitored oil flow. Performance Software as well as in the Packager
Standards Section 6: Lubrication. These range
from a proximitor that provides a signal to the
control panel, allowing shutdown logic and flow
calculations to be programmed in the panel, to a
no-flow device with on board programming for
shutdown timing and flow calculations.

See the Cylinder Lube Oil Supply for the location Refer to the Ariel Pricebook for these options.
of a lubricator no-flow switch in the cylinder
lubrication system. Please refer to our Vendor
Ion-nitriding
Literature on the website for literature on the
available lubricator no-flow switches. Ion-nitriding is a thermal process by which
nitrogen ions are diffused onto the surface of a
metal. The process is done in a vessel called an
Tubing
ion-nitrider. The piece to be nitrided is placed
Tubing and Swagelok fittings are used on both inside the vessel. Air in the vessel is pumped out,
the frame lubrication system and the cylinder and replaced with a nitrogen rich atmosphere. A
lubrication system. On larger frame classes, negative charge is applied to the work piece,
some of the frame lubrication system includes which causes nitrogen ions to bombard the work
welded pipe. piece.
Tubing is provided in 304 / 304L stainless steel, Ariel ion-nitrides cylinders, piston rods in the
ASTM A213/A269/A511. A minimum size of 1/4 packing wear area, and variable volume
inch O.D. with 0.035 wall is applied. 0.065 inch clearance pocket stems.
wall tubing is used on higher pressure
Ion-nitriding increases the surface hardness of
applications. Fittings are Swagelok zinc plated
metals to improve wear resistance. The following
steel fittings.
table outlines the effect of ion-nitriding on the
An option to apply 316 / 316L stainless steel surface hardness of Ariel’s piston rods and
tubing and 316 / 316L Swagelok fittings is cylinder bodies.
available.When selected, the 316L stainless steel
tubing and fittings will be applied to all frame
and cylinder lubrication tubing. Tubing is
differentiated from welded piping for the
stainless steel options.
On larger frames welded pipe is required for the

frame oil pump suction pipe (JGC:D:F/4 and
larger) or the oil filter to gallery pipe (KBZ:U/2
and larger). The oil filter to gallery pipe is
downstream of the oil filter. The material for
these piping sections is carbon steel with carbon
steel fittings and flanges. A separate option is
available for these frame classes to provide 316L
welded oil piping.
Items provided in carbon steel despite selecting

the stainless steel tubing or stainless steel piping
options include the frame suction strainer and
the oil gallery pipe. Both of these are internal to
the crankcase and below the normal oil level.

Ion-Nitrided
Base Hardness, Thickness of
Material Component Hardness, Rockwell
Rockwell C Hardened Layer, in
C
ETD-150 piston rods 29 57-63 0.005-0.006
Gray Iron ASTM A278 cylinder bodies <20 57 0.006
Ductile Iron 60-40-18 cylinder bodies <20 57 0.006
416 SST VVCP stems <20 70+ 0.005
Ductile Iron cylinders of 80-55-06 are not ion- Cylinder, Side-by-Side Clearance
nitrided.
Some compressor cylinders will not fit side-by-
17-4PH Piston Rods are chromium nitrided in the side on certain frames. For a listing of such
packing travel area to a hardness level of 2500 cylinders refer to the Ariel DataBook, or the Ariel
Vickers. Performance Program.
Tungsten carbide coating can be applied as an There may be difficulty installing suction valve
option on piston rods for packing travel. unloaders on large cylinders installed side-by-
side on a frame. Contact Ariel Design Engineering
Tungsten Carbide Coating for a determination if suction valve unloaders
can be installed on all valves of adjacent
Tungsten carbide coating can be applied to cylinders.
Ariel's piston rods using a High Pressure High
Velocity Oxygen Fuel process, HVOF. The HVOF
process is a thermal spray process by which fuel, Special Flange
oxygen and hydrogen are burned to produce a Ariel provides special flanges for all cylinders that
hot high pressure gas stream. A tungsten carbide, do not utilize standard Industry flanges. Ariel's
cobalt and chromium powder is injected into the special flanges come in four main types, Dual
high velocity gas stream and is accelerated Nozzle, Racetrack, Peanut, and Taper-Lok.
towards the piston rod. The high energy and hot Special flange outline drawings are available in
powder forms a near pore-free density level of the Ariel Databook listed next to the cylinder
tungsten carbide on the surface of the piston rod. outline drawing. These outline drawings show
For the Ariel piston rods, the HVOF process the flange style, size, and use of orifice plates.
creates a final coating thickness after machining
of 0.003 to 0.005 inches and a hardness level of
68-73 Rc.

Orifice Plate
Cylinder Standard Special "For Orifice"
Flange Type Sealing Thickness
Class Material Bolting Bolting
Required
13-1/2JG:J:M Dual Nozzle O-ring SA-105 Fatigue Option 1/2" with o-

Fighter ring groove
17- Dual Nozzle O-ring SA-105 Fatigue Option 1/2" with o-

1/4R:RJ:H:E Fighter ring groove
19-
1/2R:RJ:H:E
22-1/2H:E Racetrack Gasket SA-516 Gr70 Fatigue Not Avail Not

and SA-53 Fighter Applicable
17- Peanut Flexitallic SA-516 Gr70 Fatigue Option 3/8"

7/8K:T:C:D:Z: Gasket Fighter
U
20-
1/8K:T:C:D:Z:
U
22K:T:C:D:Z:U
24- Peanut Flexitallic SA-516 Gr70 Fatigue Option 3/8"

1/8K:T:C:D:Z: Gasket Fighter
U
26-
1/2K:T:C:D:Z:
U
19BL:VL:BM:V Peanut Flexitallic SA-516 Gr70 Fatigue Included Included

M Gasket Fighter
Higher Taper-Lok Taper-Lok SA350 LF2 Studs and Included Included

Pressure Seal Ring Nuts
Cylinder Class
(refer to
Databook)
1-3/4SG-FS- SAE Straight O-Ring Fitting By None Not Available Not Available
HE Thread Packager
2-1/2SG-FS-
HE
Dual Nozzle Flanges: sizes. The bolting is high strength fatigue fighter
bolts, and the sealing is accomplished with an o-
Dual nozzle flanges are used on medium sized
ring. When orifices are required, Ariel can provide
cylinders where there are two separate nozzles
longer bolting and an extra o-ring ("for orifice"
for suction, and two separate nozzles for
option).
discharge. These nozzles are weld neck flanges
and need to be butt welded to nozzle piping
between the flange and the pulsation vessel
body. These nozzles are not standard ANSI flange

orifice" option). The flanges need to be welded to

the nozzle piping between the flange and the
pulsation vessel body. The Customer must
specify either butt or fillet weld style flanges at
time of order.
Racetrack Flanges:
Racetrack flanges are used on the larger low

pressure cylinders, 22-1/2H and E. The bolting is Taper-Lok:
high strength fatigue fighter bolts, and the
Taper-Lok flanges are used on higher pressure
sealing is accomplished with a gasket. The flange
cylinders. Ariel provides the flange, seal rings,
nozzle is designed to weld directly to the
orifice plate and bolting. The orifice plates ship
pulsation vessel body or to a transition piece.
with a minimum bore and require drilling to the
required orifice bore by the Packager.
Peanut Flanges:
Peanut flanges are used on the larger cylinder

classes. These cylinders have two separate flow
Taper-Lok flanges are designed to ASME Boiler
areas like the dual nozzle cylinders, but the
and Pressure Vessel code Section VIII Div 1. If
flanges are connected together resembling the
design and calculations are required to Div 2, the
shape of a peanut. The flanges are plate material
packager can procure the flanges, seal rings and
ready for welding the pulsation vessel nozzle
orifice plates directly from Taper-Lok.
piping, two nozzles per flange. The bolting is high
strength fatigue fighter bolts, and the sealing is
accomplished with flexitallic gaskets. When
orifices are required, Ariel can provide longer
bolting and an extra flexitallic gasket ("for

When stainless steel Taper-Lok flanges are Flanges are designed to ASME Boiler and
required by the Client or Packager (such as on Pressure Vessel code Section VIII Div 1. Division
carbon dioxide applications) Ariel will provide IIfor Ariel supplied flanges are not available. See
the studs and nuts and a deduct for the carbon Taper-Lok above for special notes on the high
steel flange parts. The Packager can procure the pressure flanges.
stainless steel flange, two seal rings and the
Dual Nozzle Flange SA-105
orifice plate directly from Taper-Lok.
Racetrack Flange SA-516 Gr 70 and SA-53
Taper-Lok flanges include an orifice plate with
minimum bore. Final bore dimensions for all Peanut Flange SA-516 Gr 70
orifice plates to be machined by the Packager.
Taper-Lok SA-350 LF2 suitable for -50 F
Refer to the outline drawings for maximum bore
limits. 304L and 316L stainless steel materials are
available options for the dual nozzle flanges and
SAE Straight Thread (Fitting Provided by
peanut flanges.
Packager)
17-4PH bolting may lower available MAWP on
The 1-3/4SG-FS-HE and 2-1/2SG-FS-HE cylinder
some cylinders, specifically the 17-
classes utilize an SAE o-ring style connection at
7/8K,T,C,D,Z,U Class cylinders and some KBB:V
the cylinder for gas inlet and discharge. These
cylinders. Refer to the Ariel Databook.
cylinders are most commonly fit up with tubing.
The SAE o-ring fittings for tubing fitting can be Orifices:
found at a local Parker Hannifin distributor,
Steel orifice plates for suction or discharge are
Parker Seal-Lok O-Ring Face Seal Tube Fitting
commonly used for pulsation attenuation.
part number 16 F5OLO.
Orifices are to be provided by the Packager.
If piping will be utilized rather than tubing, a Longer bolts and extra o-rings / gaskets are
Grayloc hub to SAE adapter can be found at a available as a "for orifice" option when orifice
local Grayloc distributor, drawing number plates are used (not applicable to welded in
H600307-1310. Care must be taken that an orifice plates).
understanding of the use of Grayloc hubs is
Ariel encourages the use of orifice plates of
known prior to incorporating a Grayloc hub pipe
specific thickness due to the special bolting types
system.
and lengths used in the "for orifice" bolting
Code Calculations: option provided by Ariel. The dual nozzle flanges
require the use of o-rings rather than gaskets.
Code calculations for the special flanges are
The o-ring groove dimensions for the orifice
available on the Ariel website.
plates are defined in the special flange outline
Materials: drawings.
Standard materials of construction for these Dual Nozzle Flanges 1/2" orifice plate with o-ring
special flanges are carbon steel. Flange materials groove
are suitable for NACE construction once suitable
Peanut Flanges 3/8" orifice plate and gasket
bolting is provided.

Taper-Lok flanges include an orifice plate with Commissioning and Operation of the
minimum bore. Final bore dimensions for all Compressor
orifice plates to be machined by the Packager.
Refer to the outline drawings for maximum bore Once the compressor is installed and the
limits. operating conditions confirmed, the valve
configuration should be reviewed. If the current
operating pressures are much different than the
Valves expected operating conditions, contact the Ariel
Response Center (ARC) to confirm the valve
Compressor valves are finely tuned check valves,
configuration. Different springs may be
cycling up to 1800 times per minute. The
necessary to ensure proper valve dynamic
variations in operating pressures, gas
motion.
composition, gas density, operating speed, and
load steps are all designed into the specific valve If the valve life proves shorter than expected,
configuration for a given application. The valve contact Ariel with the unit serial numbers,
design consists of the proper size, plate mass, current valve part numbers and current
plate lift, spring force, and plate and spring operating conditions. The valve configuration
materials. can be confirmed, or altered as necessary.
The valve selection is optimized for the specific Valve Analyses
operating conditions provided within each
A valve dynamic motion analysis can be provided
compressor application. When operating
for the valve design condition upon request. This
conditions vary outside the original parameters,
is a mass spring damped motion review of the
the valve selection should be reviewed to
plate motion, including impact velocities and
confirm appropriate plate motion. This may
motion analysis. Response to the acoustical
mean a change in valve springs, plates, or
pulsations is not included in the valve motion
sometimes entire valve.
study.
Operating across a wide speed range, as with a
Valve Lift
variable speed electric motor driver (VFD), will
require special consideration in the valve The current CP valve type is offered in one valve
selection. The speed range will depend upon lift. This lower lift offers improved valve
several variables. Generally the valve selection reliability, while maintaining or improving upon
will not tolerate a speed range greater than a 2:1 valve efficiency (flow area).
turndown. Further consideration may be needed
below half frame rated speed, as this may impact Older valve styles were offered in varying lift
valve reliability. configurations to accommodate wider, or
varying operating conditions. Low lift valves
improved reliability by reducing impact stresses
or improving closing timing. However, this also
increased power usage, rod loads and discharge
temperatures. The increase may be slight in most
cases, but should be reviewed and considered.

Low lift valves were required when suction Further information on Special Tools can be
pressure, discharge pressure, and / or operating found on the Ariel website within the
speed vary greater than 25%. Contact Ariel with Maintenance and Repair Manuals.
the full range of operating conditions for review
of valve type and lift.
Hand Tools
See Also:
Ariel compressors are provided with special
• Valve Lift tools, and have a number of optional tools
• Pseudo-q Value available. All available tools are listed in the Ariel
• Suction Valve Unloaders performance software to allow separate
• High Clearance Valve Assembly purchase. Details on the special tools, and what
• Adjusted Equivalent Valve Area is included or recommended for each frame or
tool option, can be found on the Ariel website
Special Tools within the Maintenance and Repair Manuals.
Ariel compressors are built with some special

KBB:V & KBU:Z frames require special hydraulic
tool requirements. Special tools that are not
torque tools for disassembly & re-assembly.
available through standard tool suppliers are
These special tools are available as an option and
provided by Ariel with each compressor.
should be included as an option in the proposal.
Special tools are priced and scoped separately to Some compressor frames require (or
allow the purchase of these based upon having recommend) the use of hydraulic tensioning
one set per location. A list of special tools is made devices. As these may be needed for each site,
available in the Ariel performance software. rather than each compressor frame, they are
provided as an optional purchase.
These special tools include:
• Hydraulic Piston Nut torque tool Ariel compressors are built using SAE fasteners.
• Hydraulic Balance Nut torque tool As SAE tools are not readily available in all
• Hydraulic Main / Conn Rod torque tool installation locations, an option to provide SAE
• Hydraulic Stud tensioner (optional) tools is available in the Ariel performance
• Hydraulic pumps, manual, electric or pneu- software.
matic
Further information on Special Tools can be
Hydraulic tools can be used on the smaller found on the Ariel website within the
frames, but are considered optional as manual Maintenance and Repair Manuals.
hand tools can be used. A full list of the optional,
recommended and required tools are listed in
the Ariel performance software for each frame.
We encourage the review and inclusion of any

necessary special tools in the initial purchase of
larger compressor frames.

Industry Specification
Comments and Exceptions
The Ariel Corporation Electronic DataBook and
Ariel Performance Program provides Ariel's
comments and exceptions to the industry
specifications. These can be accessed by
selecting the frame of interest, then right clicking
on the frame.
The industry standard comments include

comments to:
• API 618 Fifth Edition, December 2007
• ISO-13631
• API-11P
• NACE MR0175/ISO 15156-1,-2,-3

Applications
Due to the potential for auto ignition of the lube
oil in air service crank case relief doors are
mandatory on JGJ frames with cylinder working
Air Service pressures greater than 1500 and short coupled
Air service can include applications for distance pieces are provided. Crank case relief
underbalanced drilling, air feed for air doors are highly recommended on all other short
separation, and seismic applications. Many air coupled guide arrangements, such as on
services have high discharge pressures. Air JGM:N:P:Q:I, JG:A and JGR:J:W frames.
compression has a few technical details for When selecting a compressor for air service,
consideration when sizing an air application. lower piston speeds may be necessary in order to
The k-value for air is relatively high, resulting in allow the heavier gas to flow through the valves
gas discharge temperatures being higher at with proper valve dynamics. The lower piston
lower compression ratios. The higher k-value speeds will lower the pseudo-q values as well as
will also result in faster discharge temperature improve the efficiency of the unit (lowering the
rises with changes in pressures. Off conditions power per unit flow value).
need to be reviewed to confirm maximum Package and Operational Recommendations:
operational temperatures are within the Ariel
1. Ariel recommends discharge valve tempera-
discharge temperature limits. Refer to the
ture sensors to detect higher temperatures
Packager Standards for information on
due to leaking or failed valves.
Instrumentation.
2. Deactivation of cylinder ends is discouraged
Mineral oil auto ignition temperatures in Air due to the potential for higher heat build up.
service are relatively low at higher pressures and Discharge temperature devices will not
drop significantly as pressures and temperatures measure internal heat build-up due to end
increase. An ester based lubricant must be used deactivation.
in air service. The lube oil auto ignition
3. Where available, provide water cooling to
temperature must exceed the compressor
packing cases to reduce packing heat.
discharge temperatures at discharge pressure.
The user must confirm the lube oil auto ignition 4. Gas piping systems must be designed to elim-
temperature is well above potential discharge inate low points where lube oil can accumu-
temperatures. Ariel limits air applications to no late. Any low point must be set up for
more than 5000 psi. Above this pressure, nitrogen continuous draining, including (but not
can be applied, with no more than 5% oxygen limited to) low points at each elbow-up and
content. gas cooler sections.
Refer to the Packager Standards for information 5. Separators are to be configured for contin-
on Cylinder and Packing Lubrication. uous draining.

Application Manual – Applications 12/13/2023
Carbon Dioxide For sweet natural gas with a carbon dioxide

concentration less than 5%, or at 5% with a
Carbon Dioxide (CO2) may combine with water to suction pressure less than 1200 psig, or with a
form carbonic acid. Carbonic acid is mildly carbon dioxide concentration up to 50% with a
corrosive and at higher pressures can condense suction pressure less than 400 psig, or with any
into a liquid which will act as a solvent and dilute suction pressure lower than 400 psig, use
the cylinder lubrication. The gas properties of standard piston rod and valve materials.
the CO2 mixture should be reviewed at the
For sweet natural gas with a carbon dioxide
required operating conditions. Gas properties of concentration outside the above limits, use 17-
CO2 can be found under the Gas Properties topic. 4PH stainless steel piston rods and stainless steel
See the chart below for recommended materials compressor valves. Most valve bodies are 416
of construction for piston rods and valves based stainless steel material and will meet the
on suction pressure and CO2 concentration. recommendations for stainless steel in CO2
service. When the standard valve body material is
Figure: Suction Pressure vs. CO2 Concentration carbon steel, the 17-4PH stainless steel valve
option should be chosen. (When changing to the
17-4PH valve material option, it is recommended
that standard valves be used for unit start-up.
Once the system is confirmed clean, the
stainless steel valves should be installed).
CO2 is soluble in mineral oils, thereby reducing

the oil / gas mixture viscosity. Mineral oils are
completely miscible into CO2, which reduces the
Standard or Stainless Piston Rod and Valves Chart
effectiveness of the oil. Compounding mineral
When the standard valve body materials are 416 oils or PAG (poly-alkaline-glycol) synthetic
stainless steel, these are suitable and meet the lubricants are commonly used. See Cylinder and
recommendations of the above chart for CO2 Packing Lubrication Requirements in the Ariel
service. Some valves have carbon steel body Packager Standards and contact Ariel in Mount
material, and would not meet the Vernon for a recommendation.
recommendations for the above chart. The valve
Compression of carbon dioxide often involves
material can be found on the cylinder data
operating conditions that are near or above the
sheets.
critical point of the gas. The gas properties will
The recommendations for compressor piston rod be very sensitive to small changes in pressures
and valve materials are: and temperatures when near and above the
critical point. When a stage suction pressure is
near the critical pressure, allow a greater margin
from the critical temperature for more stable gas
properties. This may mean operating at a
suction temperature of 40 to 50 F (20 to 30 C)
above the critical temperature. When a stage

suction pressure is above the critical pressure, A controlled temperature system can be
allow enough suction temperature to maintain accommodated during higher ambient
proper gas properties. Proper gas properties temperature swings through gas cooler louvers
means maintaining a suction compressibility (Z) and fan control. If this is not enough to control
value above 0.4, and preferably above 0.5. In this the gas temperature out of the cooler, hot air
"dense phase" region above the critical pressure recirculation or heaters may need to be provided
the gas can have properties of either a gas or a in the cooler design. Controlling with a bypass
liquid and the density of the gas will fluctuate around the gas cooler with a temperature control
greatly with small changes in pressure or valve allowing mixing of hot and cold gas may not
temperature. be suitable, if the cooled gas condenses in the
cooler.
When selecting a compressor for carbon dioxide

service, lower piston speeds may be necessary in
order to allow the heavier gas to flow through the
valves with proper valve dynamics. The lower
piston speeds will lower the pseudo-q values as
well as improve the efficiency of the unit
(lowering the power per unit flow value).
Carbon Monoxide
Gas properties of CO can be found under the Gas
Properties topic.
Carbon Monoxide presence in the gas stream will

require a lubricated cylinder construction. Non-
lubricated applications should be avoided. This
is due to the increased risk of Carbon
Due to the sensitivity of the gas properties to
Dissociation. Carbon Dissociation may cause the
small changes in pressure and temperature in
formation of hard carbon deposits and CO2. This
this "dense phase" region, near and above the
critical point, the interstage temperature may process can also result in carbon dust
need to be controlled. If the gas suction accumulating in the piping. This dust may be
temperature is allowed to vary, the gas density pyrophoric, combusting when coming in contact
will fluctuate widely and can cause large changes with air.
in the acoustical response of the gas piping Discharge temperatures should be limited to
system. This can lead to acoustic force driven 255° F (124° C).
shaking of the equipment.
When the combined content of carbon monoxide
Critical pressure and temperature are provided and hydrogen approaches 50%, PRC guidelines
on the phase envelope within the Ariel will govern the selection of equipment.
Performance Program.

Ariel does not provide non-lubricated cylinder Gas storage compressors are often installed in
construction for carbon monoxide applications. highly automated systems. Capacity control
devices are often pneumatically operated rather
than manually operated. This would include
Gas Storage Service pneumatic actuated fixed volume clearance
Gas Storage service includes applications where pockets and suction valve unloaders.
gas is injected at relatively high pressures into
formations, wells, caverns for future use or sale.
High Gas Molecular Weight
Gas storage applications may also include the
compression for withdrawal from these storage It is always recommended to use a gas analysis
sites during periods of demand for the gas. for the highest accuracy for predicted
Discharge gas pressures will swing widely during performance. For the normal natural gas
the injection process, while suction pressure will mixtures with .56 to .80 specific gravity a specific
remain relatively stable. Suction gas pressures gravity entered for performance predictions is
will swing widely during the withdrawal process, acceptable. If the gas contains gas constituents
while the discharge pressure will remain outside the normal pipeline gas mixtures (ie.,
relatively stable. carbon dioxide, nitrogen, hydrogen sulfide,
hydrogen...) a gas analysis will provide more
Due to the wide range of pressures, compressor
accurate performance results.
valves are often required to be low lift for proper
dynamics. When gas mixtures are lighter than .35 specific
gravity (10 mole weight) or heavier than 1.35
The elevated storage pressures often require two
specific gravity (39 mole weight) it is
stages of compression as the storage sites fill.
recommended to contact Ariel Applications
However, much of the injection process and
Engineering. The VMG gas method should be
most of the withdrawal process can be done with
used for gasses outside the use of natural gas.
a single stage of compression. Many gas storage
applications are designed to operate all cylinders When only a specific gravity is specified, the gas
in parallel for a single stage of compression properties (K value and compressibility) are
during the early phase of injection and during based upon a generalized hydrocarbon mixture.
withdrawal. The gas piping is then reconfigured This could lead to inaccurate compressor
through valving to operate with two stages of performance predictions when other gas
compression at the final phase of injection. This constituents are present outside the normal
one stage / two stage operation allows for much natural gas mixture. Air should never be entered
greater use of the installed power and much by a specific gravity.
more flow during the lower ratio phase of the
Heavier gasses will create higher pressure losses
processes.
through the valves. This pressure loss is
calculated through the pseudo-Q values. When
the pseudo-Q values are high, reaching or
exceeding 15, a slower piston speed will be
necessary.

Often times heavy gas applications are also wet

gas or low suction pressure applications.
See the Packager Standards Section 6:

Lubrication for information on applying the
appropriate cylinder lubricant and rates for high
gas molecular weight applications.
Heavier gasses may approach the dew point at

the higher pressure interstages. If so,
temperature controls for the interstage may be
necessary to avoid gas product condensates.
Light gasses, molecular weight less than 12 Hydrogen Service

(specific gravity less than 0.4), are considered low Hydrogen is a diatomic gas used in a number of
molecular weight applications and must be refining and petrochemical processes.
reviewed by Ariel Application Engineering. A
valid gas analysis must be provided for these Hydrogen has a high ratio of specific heats,
applications. The VMG gas method should be therefore will increase in discharge temperature
used for light molecular weight gasses. with smaller increases in compression ratio.
Temperature limitations are 250 F (121 C) for
Special attention will be paid to the selection of selection purposes and no greater than 275 F
compressor valves for low molecular weight (135 C) in operation. Shutdown setting should be
applications. The pseudo-Q-value must exceed no greater than 300 F (149 C). Additional stages of
1.0 for all operating conditions. The application compression may be necessary to maintain these
will be reviewed with the valve supplier to select lower discharge temperatures.
the proper compressor valve. Ariel will also
adjust the expected compressor capacity to PRC cylinders and application guidelines are
account for higher piston ring blow by. It must be necessary for hydrogen applications. The
noted that any changes to the compressor valves application guidelines include lower discharge
that may be required to increase the pseudo-Q- temperatures and lower piston speeds. Helium
value and any capacity adjustments may result in leak testing is required for cylinders used in
an increased HP (kW) requirement. Hydrogen service.
Applications that involve higher than 50% by

volume of hydrogen shall be sized to limit the Non Lube Compressor
internal discharge temperature to 275 °F. Cylinders
Cylinders in these applications must have a
helium leak test and packing cases with lapped Please refer all non-lube applications to the Ariel
cups. Application Engineering Department.
Non lube applications will be limited to the

following compressor frame and cylinder
classes:

• Frames – JGA, JGJ, JGK, JGT, KBK, KBT, JGD, Rubbing speed is a factor that must be
JGF, KBU and KBB considered for all Non-Lube applications. The
• Cylinders - JG, RJ, JGK, JGT, KBK, KBT, JGD, piston speed limit for Non-Lube applications is
JGF, KBU and KBB 750 feet per minute (3.81 meters per second).
Non-lube applications will require that the Refer to Process Rotative Speeds for maximum
following application guidelines be strictly allowable rotative speeds for each frame model.
adhered to:
• Use a long two compartment distance piece Offshore Applications
(API – 618 Fourth edition Type C) with oil
slingers in both compartments; Offshore production applications carry
• Piston rod materials for non lube service will additional considerations for compressor
be as follows: selection, packaging and analytical studies. A
• For non-corrosive applications – ETD 150 conservative approach to the selection will offer
with a Tungsten Carbide coating. the benefit of longer time between maintenance,
• For corrosive applications – 17-4 PH for less maintenance work and replacement
Stainless Steel with a Tungsten Carbide parts in this remote environment. This would
coating.
include reduced speeds, lower discharge
• Limit cylinder internal discharge temperature
temperatures and conservative rod load usage.
to 275°F (135°C) for selection, 325°F (163°C)
for maximum shutdown limit Offshore structures do not carry the immense
• Limit cylinder discharge pressure to 1500 psig mass of earth and concrete to absorb the many
(103 barG) forces and couples associated with reciprocating
• All non lube cylinders are provided with water compressors. Therefore, selecting a compressor
cooled packing and must be connected to a
for offshore installation must keep this in mind.
packing cooling system.
When possible, a four throw compressor will
• Compressor valves, pistons (and piston trim)
are specifically designed for non-lube service. carry lower forces and couples than a two throw
compressor. A six throw compressor will carry
Non lubricated cylinder construction can be even lower forces and couples.
applied for sour gas services, but is limited to
sour level 1, less than 2% H2S content by volume. The forces and couples associated with
NACE Stainless Steel Valves are required along reciprocating compressors can come from a
with the Sour Level 1 trim (stainless steel piston number of sources. The offset distance along the
rods, purged packing, proper purge / vent crank centerline between opposing throws
system, long two compartment distance piece). creates a couple. Different reciprocating weights
on opposing throws, or between pairs of
Internal piston ring blow-by is accounted for in opposing throws creates forces and couples.
the Ariel performance program as a relation to Ariel balances the reciprocating weight on
the gas mole weight. opposing throws to a very tight margin to limit
the unbalance forces. The reaction to the

conversion from rotating to reciprocating motion • Lloyd’s Register of Shipping in United

at the crosshead guide creates vertical forces at Kingdom
the crosshead guides. Torsional vibration forces • Bureau Veritas in France
can resolve into lateral vibration forces on some FPSO documentation as required by all the third
configurations. party certification is termed Design Review by the
A heavier skid structure will be necessary for classification organization.
greater rigidity with offshore packages. This 1. For each compressor, an affidavit is required
includes a "full pedestal width" construction, from the manufacturer stating that design
tying the structure under the crosshead guide and fabrication have fully complied with an
support to the frame supporting structure. applicable API standard, except as noted. All
exceptions shall be listed and if no exceptions
Along with the torsional and acoustical analyses,
are taken to the specifications, then the affi-
a full mechanical analysis of the skid and
davit should indicate as such.
surrounding supporting structure is necessary.
2. Compressor performance runs information
Gathering, vapor recovery, gas lift, gas re- shall be provided indicating maximum allow-
injection and fuel gas booster for gas turbine able suction and discharge pressures and
generator are most common FPSO applications. corresponding temperatures (both
maximum and minimum), as well as
Dry sump is recommended for vessel pitch, roll
maximum rated discharge pressure.
and yaw. Most often, 316SST tubing and fittings
as well as duplex oil filter are specified by end 3. For compressors handling hydrocarbons,
user customers for offshore environments. casing (cylinder) drawings and casing
(cylinder) strength calculations may be
Third party certification is often required for
required. The casing strength calculation
FPSO, or offshore applications. These would
shall include cylinder thickness calculation
include:
and inlet/outlet nozzle reinforcement calcu-
• FPSO - Floating, Production, Storage, lation. If casing drawings cannot be
Offloading Vessels
submitted due to confidentiality, a sketch of
• FSO - Floating, Storage, Offloading vessels,
casing drawing including diameter and thick-
without the processing facilities
ness and inlet/outlet diameter and thickness
• FSRU – Floating, Storage, re-gasification and
offloading vessels information is acceptable.
• FLNG – Floating Liquid Natural Gas Produc- • Ariel requirements to FPSO documentation
tion vessels are compilation and documentation of
• FDPSO – Floating, Drilling, Production, • Compressor configuration with serial
Storage and Offloading vessels numbers and general model ratings
The third party certification requirements for • Compressor frame and cylinders outline
FPSO applications are specified by FPSO drawings
Classification Organizations as listed here. • Compressor frame and cylinders data sheets
• Cylinder casing design data
• ABS ( American Bureau of Shipping) in USA
• Compressor performance data sheets
• DNV (Det Norsk Veritas) in Norway
• Comments and exceptions to API-618 and 11-
P Specifications

• ASME Code Calculations for Special Flanges Propane

Offshore environments can be corrosive due to
Propane (C3H8) applications will typically be
salt water spray. Cylinder and valve cap bolts can
be provided in 17-4PH stainless steel if salt water classified under the application guidelines for
corrosion is a concern. The NACE Cylinder Bolting High gas molecular weight, low suction
option will apply 17-4PH bolting and studs for the temperature applications or low gas suction
cylinder heads and valve caps. pressure (The most stringent of these criteria
shall apply).
There are several special application

Oxygen considerations for propane service. The
Oxygen service requires special cleaning minimum suction temperature for gray and
processes during manufacturing of the ductile iron is -40°F (-40°C). Ariel Application
compression equipment. Ariel does not provide Engineering should review all applications with
compression for oxygen service. suction temperatures below 0 degrees F (-18
degrees C).
Oxygen in a hydrocarbon based gas stream can
be a concern for combustion. Ariel limits the Some applications utilize propane in a closed
oxygen content in a hydrocarbon service to 5% to loop refrigeration service. These applications
ensure the lower explosion limit is not reached. must be reviewed to insure that the settle out
pressure of the system is less than the MAWP of
Oxygen can be introduced into the gas stream
the system or that adequate controls and
when suction pressures are near or below
protection are provided to protect the
atmospheric pressure. When considering suction
compressor cylinders. In closed loop
pressures near atmospheric pressure, an oxygen
refrigeration service, cylinder lube rates should
sensor downstream of the first stage of
be monitored and may require adjustment.
compression is recommended. Oxygen content
will be limited by either the 5% listed above, or High Pseudo-q values are common in Propane
the limits by the gas composition requirements applications. Valve selection is critical in these
by the client, whichever is lower. applications, therefore a valid gas analysis is
required.
In inert gas based compositions, such as
nitrogen, oxygen content will impact the auto Gases with high propane content tend to dilute
ignition temperature and pressure for the standard compressor cylinder lube oils, thereby
lubricating oil. Any composition of inert gas and reducing the gas/oil mixture viscosity. Propane is
oxygen above the oxygen content of air (21% oil soluble and tends to wash the lubrication film
oxygen) should be reviewed for auto ignition away.
temperature and pressure, and lubricating oil
Refer to the Propane Gas Properties for
selection.
information on propane gas.
See Cylinder and Packing Lubrication

Requirements--6 in the Ariel Packager Standards
for guidelines regarding cylinder and packing
lubrication for Propane service.

Sour Gas With higher percentages of H2S in the gas stream,

a review of the phase envelope and dew point of
Hydrogen sulfide is considered corrosive, toxic, the gas constituents (not including water vapor)
and lethal. As such, Ariel has specific is recommended. At higher levels of H2S and
recommendations as to the materials and
higher pressures, the interstage cooling can
compressor configuration options when
easily reach the dew point for the H2S in the gas
compressing gas that contains H2S. Hydrogen
stream. Most often, condensation of the H2S is to
Sulfide (H2S) can embrittle high strength, high
be avoided.
hardness carbon steels, and most martensitic
stainless steels (for a full and specific list of Sour Gas service, Level 1, can be applied with
material compatibility with H2S refer to NACE non-lubricated cylinder construction. NACE SS
MR-0175, ISO-15156). Valves will be required along with the
requirements and recommendations of Sour
Ariel's equipment configuration Level 1 trim below.
recommendations for sour gas service are based
upon field experience and the NACE guidelines Recommendations / Requirements for Sour
for the protection of the equipment. Gas Service:
It is the End Users responsibility to be aware of

the level of H2S present, and to take all necessary
precautions for the protection of personnel from
harmful leakages of gas to the atmosphere.
Selection Recommendations / Requirements

for Sour Gas Service
Several considerations should be made when

selecting compressors in sour gas service. As the
gas is both corrosive and toxic, special safety
requirements are necessary for the maintenance
of the equipment. It may be suitable to provide a
more conservative selection to lengthen the time
between maintenance. This would include
operating at slower piston speeds and allowing
for lower discharge temperatures.
The toxic and lethal nature of the gas dictates the

use of an appropriate purge and vent system to
ensure the gas leakage at the packing case and
distance pieces is not vented to the atmosphere.
Please refer to the Packager Standards Section 8
Packing and Distance Piece Vent Systems for this
topic..

100 ppm to 2% H2S > 2% H2S

Sour Level 1 Sour Level 2
Distance Piece Arrangement S2C / L2C / Single with purge wiper L2C (Recommend)
(Requirement)
Piston Rod Material (Requirement) Stainless Steel Stainless Steel
Purge Packing (Requirement) Purged Purged
Flushing Lube N/A Flushing Lube on Stage 1

(Recommend)
Stainless Steel Valves Standard Valves Stainless Steel
Forged Steel (-VS) Cylinders Use lower strength 22Rc cylinder bodies, or stainless bodies even as low as 5-
(Requirement) 10 ppm of H2S content
Optional Equipment: The long single compartment distance piece with

• Cylinder Bolting Material wiper purge is available on the KBE:K:T, KBU:Z
• Cylinder Body Material and KBB:V frames.
• Lubrication Tubing and Fitting Materials Refer to Packager Standards Section 8 Packing
• Separate Lube Supply and Distance Piece Vent Systems for notes on a
Distance Pieces Arrangement purge system for sour gas.
A two compartment distance piece, or a long Piston Rod Material

single distance piece with wiper seal purge are Ariel standard piston rod material is 4100 series
required for sour gas service. These carbon steel heat treated for strength. These are
configurations offer the ability to create a purge not suitable for sour gas service as defined by
and vent system which segregates the crankcase NACE MR-0175. For sour gas service with 100 ppm
and operator atmosphere from the packing and greater H2S content stainless steel piston
leakage.
rods are required. Ariel stainless steel piston rod
Long two compartment distance piece, "L2C", is material is 17-4PH in the double H1150
recommended above 2% H2S content as this condition, UNS S17400, (per NACE MR-0175), Rc
provides better containment of the gas leakage. 33 maximum, chromium-nitrided in the packing
S2C distance piece and long single compartment travel area for a surface hardness of 2500 Vickers.
distance piece with purged wiper seal can be The chromium nitride process has a length
used above 2% H2S content, but do not offer the limitation due to manufacturing constraints.
same level of protection and flexibility for the Longer stainless steel piston rods will be
vent / purge system design. tungsten carbide coated.
Two compartment distance pieces are available Purge Packing

for all units except for the JGM:N:P:Q and KBE
frames.

Ariel requires the use of "Purge packing" for sour bodies and springs. Flushing oil is available as an
gas services with 100 ppm and greater H2S option on all units. If the first stage flushing
content. The purpose of purge gas is to block and recommendation for Sour Level 2 is not taken,
contain hazardous, toxic, flammable or corrosive provisions for flushing on the pulsation vessel
gases, and to prevent such from entering the nozzle are recommended.
compressor frame where damage to the running Some cylinders have two nozzles at the suction
gear, or personnel safety hazards can occur. The (dual nozzle and peanut flange). Flushing lube
purge gas must be sweet natural gas or an inert for these two nozzle cylinders is configured for
gas, such as nitrogen. Purge packing refers to a one flushing lube point per cylinder. This is
packing case modified to accept an external sufficient, considering the flushing lube
purge pressure 15 to 20 psi above the primary connection is in the suction pulsation vessel
packing vent/drain pressure with no more than 5 nozzle. If a client wants to apply flushing to both
psi external system back pressure. Refer to Ariel's pulsation vessel nozzles, the packager can install
recommendations in Packager Standards a pipe tee to split the single line provided.
Section 8 Packing and Distance Piece Vent
Systems for a purge system for sour gas. See also Stainless Steel Valves
"Packing Leakage". Ariel standard valve body material is 400 series
When the purged packing option is selected on a stainless steel and 1040 carbon steel. These are
long two compartment distance piece, the not suitable for sour gas applications per NACE-
intermediate and wiper seal sets will be MR0175. Ariel recommends the use of NACE
configured for purge along with the pressure compliant stainless steel valves for sour gas
packing case. When the purge packing option is services with 2% and greater H2S
selected on a long single compartment for the content.Stainless steel valves generally consist
KBE:K:T, KBU:Z or KBB:V frames, the wiper seal of:
will be configured for purge along with the • Seats and guards: 17-4PH - H1150
pressure packing case. • Plates: Nylon, MT or PEEK. 17-7PH or 15-7PH
Flushing Lube if metallic plates
• Coil springs: Nimonic 90
Ariel recommends the use of cylinder flushing • Spring plates: stainless steel (equivalent to
lube for first stage cylinders for sour gas services 420)
with 2% and greater H2S content. An atomizer for
It could be prudent to start up a unit with
flushing lube injection can be constructed of standard valves and replace those with the
tubing inserted into the gas stream at the suction stainless steel valves after any start up problems
pulsation cylinder nozzle with the end opened have been solved and piping debris has passed
with a diagonal cut. The Packager would provide through the unit.
the lube lines from the end of the guide to the
suction pulsation vessels cylinder nozzle. NACE Stainless Steel valves are required for Sour
Flushing lube lines will be tubed to the end of the Level 1 service in non-lubricated cylinder
crosshead guide from the distribution construction.
block. Flushing oil is used to ensure corrosion
protection for the suction valves, both the valve

Optional Equipment for Sour Gas Double acting forged steel cylinders that are not
Service suitable for sour gas service, will be flagged in red
in the performance software when H2S is entered
Cylinder bolting into the gas analysis. Most forged steel tandem
Standard cylinder bolting for sweet and sour gas cylinder arrangements are suitable for H2S
services consists of Grade 8 valve cap, head end content due to the controlled hardness of 22 RC
head, crank end head and packing case cap maximum.
screws. Cylinder bolts are outside the gas Lube Tubing
containment and not considered "wetted".Ariel
provides an option to replace these bolts with 17- Ariel standard cylinder and frame oil system is
4PH stainless steel bolts for the valve caps, head 304 / 304L stainless steel tubing with zinc plated
end head, crank end head and packing case carbon steel fittings. An option is available to use
bolting.The 17-4PH fasteners for the heads and 316 / 316L stainless steel tubing and 316 stainless
packing case are bolts. The 17-4PH fasteners for steel fittings. This would encompass the frame
the valve caps are studs. and cylinder tubing and fittings on a unit. A
separate option is available for upgrading
Cylinder Body Materials welded frame oil piping from carbon steel to 316L
Standard cylinder body materials are: stainless steel, both on the pump suction and
downstream of the filter on larger units. Fittings
• ASTM A278 Grade 40 gray iron
and plugs outside the frame and cylinder oil flow
• ASTM A536 Ductile iron 80-55-06
are not included in these stainless steel options.
• ASTM A395 Ductile iron 60-40-18
• AISI 4340 Forged steel Separate Lube Supply
• ASTM A668 Class J forged steel
Provision is made on all units to use a separate oil
Forged Steel Cylinder Body Materials source for the cylinder bores and packing cases.
Attention must be paid to forged steel cylinder Ariel standard is to tube from the main frame oil
selections for hydrogen sulfide content. The header to the inlet of the cylinder lubricator
NACE MR-0175 Stress Cracking Region will be pumps. The packager can remove this tube, plug
used to determine how much H2S is allowed for the connection at the main frame oil header and
connect the separate supply to the inlet of the
AISI 4340 cylinder bodies.Most Ariel forged steel
lubricator pumps. Sour gas services typically
cylinder bodies are manufactured from AISI 4340
require a special lubricant through this separate
high strength carbon steel.This material is not
lube supply. Refer to Section 6 of the Packager
suitable for H2S content, even as low as 5 to 10
Standards for lubrication recommendations.
ppm. When even small amounts of H2S is
present, forged steel cylinders will need to be
either softened to 22 RC or manufactured of 17-
4PH Stainless steel.This will impact most Ariel
double acting forged steel cylinders.

Wet Gas
Wet Gas is any gas or gas mixture in which one or
more of the constituents is at or very close to it’s
saturated vapor pressure. The constituent may
or may not be water vapor. A valid gas analysis is
required to verify gas properties.
Special attention must be paid to the gas

separation and piping upstream of the
compressor. They must be designed such that no
free liquids are permitted to enter the
compressor or accumulate in the piping or
bottles, causing "slugs" of liquid to carry over.
Consideration should be taken for two-phase
flow between the gas cooler and the stage inlet
separator, if liquids are dropping out between
stages. Gas flow rate between stages will also be
lowered by the gas equivalent amount of liquids
dropping out due to interstage cooling.
When gas condensates are to be avoided, it is

appropriate to raise the interstage temperature
to create a separation between the interstage
temperature and the dew point of the gas. A 20 to
30 F (10 to 15 C) separation is recommended.
Wet gas will tend to dilute the cylinder lube oil.

See Cylinder and Packing Lubrication
Requirements--6 in the Ariel Packager Standards
for guidelines regarding cylinder and packing
lubrication in wet gas service.

Gas Method
The gas method refers to the equations of state The VMG method can be used for all applications.
used to calculate the gas properties such as the The advantage of VMG is its accuracy and
ratio of specific heats, or N-value, and the condensate flash calculations when running
compressibility values, or Z-values. performance on heavy gasses or non-
hydrocarbon based gasses. The VMG method
The Ariel performance software allows the use of
performs hydrocarbon liquid drop-out flash
either the Hall equation of state (developed by
calculations as well as water condensate
the Chemical Engineering department at Texas
calculations. The VMG equation of state
A&M University), or the VMG thermal software
supports thousands of gas components.
(developed by Virtual Materials Group). The VMG
software uses an APR, Advanced Peng Robinson, Ariel performance software will flag the user if
equation of state. The VMG software includes a the Hall option is used when the VMG option
larger number of available gas components and should be used due to the potential of non-water
the ability to perform liquid drop-out flash liquid dropout.
calculations.
For assistance or questions regarding either gas
The Hall method can be used when running property calculation method please contact The
"natural gas" based applications. The advantage Ariel Application Engineering Department.
of Hall equation of state is its speed when
running larger multi-run calculations with
natural gas where the speed of the multi-run may
be hampered by the VMG calculation method.
The HALL method includes water condensate
calculations. The Hall equation of state supports
30 gas components.

Application Manual – Gas Method 12/13/2023
Gas Properties - Air

Gas Name Chemical Formula Chemical Family
Air Air Non-Flammable Gases
Synonym(s) Breathing Air, Compressed Air and Medical Air
Molecular Critical Temperature

Critical Pressure (psia) Ratio of Specific Heats
Weight (R)
28.975 547 239 1.406
Physical Characteristics Solubility
Colorless, Odorless Slightly soluble, but main components are higher soluble.
Applications or Uses
Many uses - Combustion, Life Support and Source of Power. Underbalanced Drilling, De-watering.
Hazards
Supports Combustion. Exposure at higher pressure can cause physical problems.
Material Requirements
Slightly oxidizing characteristics. Can be contaminated by corrosive components (CO2, NH3, H2S etc.). Many
applications require non-lube construction. Materials will be designed for continuous duty at 400 F (204 C), however,
applications are to be limited to 350 F (177 C) discharge shutdown temperature.
Lubrication
Standard guidelines for lube or non-lube service. Special lubricants for greater than 500 psi. Typically use mineral oils
when less than 500 psi and a diester when greater than 500 psi. Special precautions should be taken to prevent oil
accumulation in piping and heat exchangers, minimize drops or low points. Prevent excessive lubrication. When
synthetic oils are to be used, they must also be used during the mechanical run test.
Comments (see also Air Service topic)
Proper temperatures must be maintained to prevent carbon build-up (leads to explosive situations) and proper
materials for applicable operating pressure must be used. Materials will be designed for 400 F (204 C) continuous duty,
however discharge temperatures will be limited to 350 F (177 C) max. Standard performance runs are used, however
humidity must be accounted for and when applicable, the inlet filter pressure drops must be accounted for. Sizing
must be based on an entire range of operating conditions. Always request all operating conditions.
Gas Properties - Carbon

Monoxide
Carbon Monoxide CO Non-Metal Oxide Gas
Synonym(s) Carbonic Oxide, Carbon Oxide

Molecular Weight Critical Pressure (psia) Critical Temperature (R) Ratio of Specific Heats
28.010 515 242 1.404
Colorless gas with metallic taste and odor Practically insoluble in water. Soluble in organic solvents
containing Benzene
Fuel. Metallurgy. Chemical Processes. Synthesis Processes.
Hazards
Extremely Toxic. Asphyxiant. Extremely Flammable.
Incompatible with strong oxidizers (Chlorine, Bromine...). At temperatures above 900 F, cast iron is attacked by CO.
Nickel and Cobalt should be avoided due to corrosion. Natural rubber and neoprene are chemically attacked by CO.
Lubrication
Standard lubricating practice recommended for pressures up to 2000 psig. Non-lube applications should be avoided
(see notes below).
Comments
Due to toxicity of gas, purged packing is always required. Two compartment distance pieces are highly recommended,
or long single compartment with a nitrogen buffered packing and purged distance piece. Limit discharge temperature
to 255 F(121 C) if possible.
Non-lubricated applications should be avoided. Cylinders tend to develop "hot spots" which result in Carbon Monoxide
Dissociation. Hard carbon deposits my be formed and CO2 produced. Limit discharge temperatures to 225 F (107 C).
Ariel does not quote carbon monoxide applications non-lubricated.
Gas Properties - Carbon

Dioxide
Carbon Dioxide CO2 Acid Anhydride
Synonym(s) Carbon Anhydride, Carbonic Acid, Dry Ice

44.010 1073 548 1.300
Colorless, Odorless Soluble in water, alcohol and alkalis
Urea Plants, Carbonation, Chilling and Freezing, Fire Protection, Chemical and Synthesis Processes, Re-Injection.
Hazards
Asphyxiant. When mixed with water, produces Carbonic Acid.
Dependent on operating conditions is be corrosive. Please review the guidelines of the Ariel Applications Manual.
Lubrication
Standard guidelines for lube or non-lube service. CO2 may combine with water to produce Carbonic Acid. This acts as a
solvent and tends to dilute cylinder lubricating oil. CO2 is soluble in mineral oils, which reduces oil/gas mix viscosity.
In addition, mineral oils are completely miscible into CO2, thereby reducing the quantity of lubricant at the lube site.
Compounding or PAG synthetics are commonly used. Follow guidelines of Ariel Packager Standards.
Comments (see also Carbon Dioxide Service topic)
When used in Re-injection or Urea plants, the gas is compressed to higher pressures and may reach critical point or
dense phase region at interstage pressures. Due to the critical temperature (88 degrees F) and pressure of 1073 psia, it
is imperative to monitor interstage pressures and temperatures. If interstage pressures are near critical or above, it
may be necessary to control temperatures out of the intercooler to ensure there is a margin above critical temperature
or dense regions.
Gas Properties - Ethylene

Ethylene C2H4 Alkenes, Aliphatic Hydrocarbons
Synonym(s) Bicarburated Hydrogen, Acetene, Elayl, Etherin
28.050 748 509.5 1.255
Flammable, Colorless, Slightly sweet odor Soluble in water and alcohol. Dilutes lube oil.
Manufacture of Ethylene Glycol. Plastics at higher pressures. Food Processing. Also used as an illuminant with other
gasses for lighting. Generally used at relatively higher pressures. .
Hazards

Asphyxiant. Dispersible over a large area and does not dissipate into atmosphere. Long range ignition possible. Handle
in well ventilated area.
Non-corrosive. Standard materials apply.
Lubrication
Standard guidelines for lube or non-lube service. Has a tendency to dissolve into lube oil, thereby reducing oil
viscosity.
Comments
No special problems with compression.

However, in the event ethylene oxide can be formed, extreme care is required. In certain cases, Ethylene Oxide and
copper can combine to form Acetylene. If Ethylene Oxide is present, do not use yellow metals.
Gas Properties - Helium

Helium He Inert Gas
Synonym(s) Helium USP
4.003 33.2 9.47 1.666
Colorless, Odorless, Tasteless Slightly soluble in water. Readily absorbed by oil.
Leak Testing, Zeppelins, Mixed with oxygen for diver breathing tanks. Typically higher pressure applications, greater
than 1000 psi.
Hazards
Asphyxiant. Handle in well ventilated area. Lighter than air, collects in overhead pockets. Difficult to detect leakage.
Non-corrosive. Standard materials. Piston rings, riders and packing ring materials need to be reviewed.
Lubrication
Standard guidelines for lube or non-lube service.
Comments
Requires Helium leak test. Follow guidelines for Low Molecular Weight as detailed in Ariel Applications Manual. Due to
the extremely high Ratio of Specific Heats, closely monitor discharge temperatures. Even though Helium has twice the
molecular weight of Hydrogen, it tends to be more difficult to seal. Elastomer seals are prone to leakage. Special seals
may be required and a double seal arrangement is quite common, if not required.

Gas Properties - Hydrogen

Hydrogen H2 Flammable Gasses
Synonym(s) Molecular Hydrogen
2.016 188 61 1.410
Colorless, Odorless, Lighter than air Slightly soluble in water. Higher solubility in oil.
Hydro-cracking, Hydro-treating and various other industrial uses. General operating ranges: 800 to 1000 PSI for
pipelines and approx. 2500 PSI for Hydrocracking.
Hazards
Explosive, Flammable. Difficult to detect. Lighter than air therefore accumulates in overhead pockets. Asphyxiant.
Should be handled in well ventilated areas. Difficult to detect, flame is invisible in daylight. Leak test by soap bubble.
Non-corrosive. Standard materials are commonly used. Cast iron cylinders are acceptable. At higher pressures >1000
PSI generally use ductile iron or steel. Piston rings, riders and packing ring materials need to be reviewed.
Lubrication
Comments
Requires Helium Leak Test. Follow guidelines for low molecular weight as detailed in Ariel Applications Manual. Limit
discharge temperature to 275 degrees F or less.
Gas Properties - Methane

Methane CH4 Alkane
Synonym(s) Marsh Gas, Natural Gas, Methyl Hydride

16.040 673 343.7 1.310
Colorless, Odorless, Tasteless Slightly soluble in water. Soluble in alcohol and most
petroleum products.
Fuel or Chemical use
Hazards
Flammable. Explosive. Asphyxiant. Lighter than air so collects in overhead pockets. Handle in well-ventilated areas.
Standard materials of construction
Lubrication
Comments
No special considerations for compression.
Gas Properties - Natural Gas

Natural Gas CH4 + HC's Alkane
Synonym(s) Sweet Gas, Marsh Gas, Natural Gas, Methyl Hydride
18.910 670 382 1.288
Colorless, Odorless, Tasteless (See Comments) Slightly soluble in water. Soluble in alcohol and most
petroleum products.
Fuel or Chemical use
Hazards
Flammable. Explosive. Asphyxiant. Lighter than air so collects in overhead pockets. Handle in well-ventilated areas.

Standard materials of construction
Lubrication
Comments
Natural Gas mixtures vary dependent on the where and how it is produced. The mixture used for Physical Properties
shown is a clean, dry, "sweet natural gas" with the following composition: 85% Methane, 10% Ethane, 3% Propane, 1%
Butane, 0.5% Nitrogen and 0.5% CO2. The information is to be used as a guideline. Special care must be taken to
determine the presence of water, H2S and debris.
Residential (and some commercially applied) Natural Gas has an odorant added to aid in leak detection.
Gas Properties - Nitrogen

Nitrogen N2 Inert Gas
Synonym(s) Nitrogen NF
28.010 493 227 1.404
Colorless, Odorless Slightly soluble in water and alcohol.
Fertilizer Production, Purge Gas, Injection
Hazards
Asphyxiant. Titanium will burn in the presence of pure nitrogen.
Non-corrosive. Standard materials of construction. Piston rings, riders and packing rings need to be reviewed.
Lubrication
Standard guidelines for air apply.
Comments
Closely monitor discharge temperature. Bone dry nitrogen can cause problems with packing, rings, and wear bands.
Ensure that materials are selected for the specific moisture content.

Gas Properties - Propane

Propane C3H8 Alkane - Hydrocarbon
Synonym(s) Dimethylmethane, LP-Gas, LPG
44.090 661 666 1.14
Colorless. Liquefied, flammable gas with a Natural Gas Almost insoluble in water, but highly soluble in alcohol
odor. Turns gaseous at atmospheric pressure and and petroleum products.
temperature.
Fuels. Used as a solvent. Refrigerant Applications. Food additive. Aerosol propellant.
Hazards
Asphyxiant. Very heavy gas, collects in low level areas. Dispersible over a large area and does not dissipate into
atmosphere. Long range ignition possible. Handle in well ventilated areas.
Standard materials of construction. Due to typical low temperatures in many applications, must ensure all materials
are acceptable for temperature.
Lubrication
Has a tendency to dissolve into lube oil, thereby reducing oil viscosity.
Comments (see also Propane Service topic)
In propane applications, it is very important to analyze gas mixture to verify properties at actual operating conditions.
In lower suction temperature applications, like refrigeration service, the first interstage may not require cooling.

Performance Application Limits

• Large Two Throw Frames
• Requiring Special Tools for Maintenance
• Pipeline Cylinders
Critical Projects • High Flows with Large Piping
Critical Projects are those projects that are more • High Frequency Components
complex and have a greater potential for • Large, Low Natural Frequency Cylinders
operational issues if special attention is not • VS Forged Steel Cylinders
applied early in the project. Ariel would like to • High Pressure
assist in the review of critical projects and • Lubrication
therefore has included a flag in the performance • Water Cooled Packings
software identifying the projects that fall in this • Available Tailrods
category.
Driver Type;
Critical Projects are defined by a review of:
• Electric Motor
Application Type: • Unique Installations
• Gas Transmission • Shaft Sizing Restrictions (see Packager's
Standards)
• Wide Range of Operating Conditions
• Always Requiring Torsional
• Wide Range of Capacity Control Steps
including Single Acting Cylinders • Often Requiring Torsional Detuning
Devices (flywheels, detuners, special
• Large drivers
couplings...)
• Difficult Valve Selection due to the Wide
• VFD (Variable Frequency Drive)
Operating Range
• Unique Installations
• Complex Acoustic Responses
• Shaft sizing restrictions
• Storage Injection and Withdrawal
• Always Requiring Torsional
• Higher Pressures
• Often Requiring Torsional Detuning
• Attention to Cylinder Lubrication
Devices (flywheels, detuners, special
• Water cooled packing cases couplings...)
• Wide Range of Operating Conditions • Wide range of speeds, often with blackout
• Difficult Valve Selection due to the Wide ranges due to torsional response
Operating Range • Large Gas Engines
• PRC (Petroleum / Refinery / Chemical) • High horsepower - high excitation forces
• Industrial Gasses • Longer drive trains
• More Stringent Specification Limitations • Often Requiring Torsional Detuning
• New Customer base Devices (flywheels, detuners, special
couplings...)
Equipment Type:
• Some larger engines designed for power
• Large Frames generation may require special couplings
• KBU, KBZ, KBB and KBV and attention to torsional results
• Some JGC, JGD and JGF • Gear Boxes

Application Manual – Performance Application Limits 12/13/2023
• Difficult to detune torsionally • Tech Services can provide assistance with

• Most often requiring special couplings installation review, start-up checklist
• Axial and Lateral Alignment Concerns review, review of vibration concerns
including Thrust Limitations
Location: Torsional Providers
• Offshore and FPSO The success of the torsional analysis depends
• Limited Access heavily on the modeling of the equipment and
• Limited Space for Maintenance operating range of the compressor. A torsional
• High Visibility provider must be familiar with moderate to high
• International Destinations speed reciprocating compressors and must be
• Less Support Infrastructure in some provided with the full range of operation of the
Regions compressor. The operating range is to include
part load cases, cases with single acting cylinders
Other:
and speed variations. Familiarity with Ariel
• Sour Gas compressors is quite helpful in understanding
• Proper Materials aux end amplitudes, the availability of the
• Purge and Vent Systems torsional data (mass elastic data, torque effort
• Pneumatic Fixed Volume Clearance Pockets data and fourier coefficient data) and availability
• Supply and vent lines of specific flywheels, detuners and internal
• Complex controls flywheels.
Project Reviews Acoustical and Mechanical

Many Critical Projects can be successful with a Providers
comprehensive review of the system during Familiarity to moderate and high speed
different phases of the project: reciprocating compressors will aid in the
1. Budget and Quotation Phase successful acoustical and mechanical analysis.
• Regional Sales Managers and Applica- Some larger skids and many platform mounted
tions Engineering can provide assistance skids may require a skid analysis to ensure
in selection vibration levels and stress levels of skid, piping
2. Order Phase and vessels are acceptable.
• Order Entry can provide assistance with Torsional and Acoustical analyses may have
scope of supply interfering recommendations. More complex the
• Applications Engineering can provide operating ranges have a greater chance of
assistance with documentation, interference between the torsional, acoustical
including torsional data
and mechanical systems.
• Tech Services can provide assistance with
packaging design for maintenance
support and vibration avoidance
3. Installation and Start-Up Phase

High Discharge Pressure Low Suction Pressure

Applications with high discharge pressures At suction pressures below 10 psig it is difficult
(greater than 1500 psig) have several design for the end user to predict what the actual supply
details to consider: pressure will be within 1 to 2 psi and/or for the
packager to predict pressure drops within a
Higher pressure applications will require special
fraction of a psi. These variations in inlet pressure
review of the cylinder lubrication oil selection as
and pressure drops can result in a significant
well as lubrication rates. Separate lube oil supply
change in horsepower and flow, either upward or
and heavier lube oils will be required. Refer to
downward, depending upon the actual suction
Packager Standards Section 6: Lubrication.
pressure.
Higher pressure applications may have gas
Ariel recommends that compressor cylinders in
condensates between stages, or operate close to
this application be oversized between 5 to 10%
critical points or dense phase regions. This will
and equipped with variable volume clearance
require special considerations for interstage
pockets or high clearance valve assemblies to
temperature controls. The Heavy Gas, CO2 and
produce the desired flow. The effect of the actual
Sour Gas topics can provide further information
suction pressure being 1 to 2 psi higher or lower
on this topic.
should be considered when selecting the driver
Higher pressures may require water cooled horsepower rating.
packing cases, or limitations on piston speed.
The Packager Standards and the performance
Vacuum Suction Pressure
software will help guide the application for water
cooled packings and pressure versus speed Vacuum suction pressures can be applied to Ariel
limitations. cylinders. The sensitivity of changes in suction
pressure should be reviewed, as in the above Low
Much higher pressure applications will utilize
Suction Pressure paragraph. Additionally, the
forged steel cylinders. A closer review for
mean cylinder pressure should be maintained
crosshead pin reversal across the operating
above atmospheric pressure. If the mean
speed range must be made to ensure sufficient
cylinder pressure is less than 5 to 10 psig, air may
reversal.
be pulled into the cylinder and into the gas
The use of the higher pressure forged steel stream through the packing cases. If operating
cylinders will require a closer review of hydrogen below 5 to 10 psig mean cylinder pressure, a
sulfide content. Not all of the forged steel purged packing can be applied, using sweet gas
cylinders are suitable for operation with for the purge gas. This provides process or fuel
hydrogen sulfide content. gas to be drawn into the cylinder across the
packing, rather than air. Consider installing an
oxygen sensor downstream of any negative
suction pressure equipment.

Maximum Allowable Discharge

Temperature
The discharge temperature limits are presented
as both an application limit and a maximum
or
discharge temperature shutdown set point. The
Ariel Performance Software provides a blue and
red flag on discharge temperature. The blue flag
represents a guideline for applying a selection.
The red flag represents the maximum discharge
temperature shutdown set point. The maximum for metric units
discharge temperature shutdown set point is
TD = Discharge Temperature, °F or °C
listed in the instrumentation section of the
Packager Standards. TS = Internal Suction Temperature, °F or °C
Table: Discharge Temperature Flags and R = Internal Compression Ratio , pressure

Limits by Service discharge / pressure suction
Service Application Max Shutdown k = Ratio of Specific Heats
Limit
High discharge gas temperature shutdowns
Lubricated 330 °F (165 °C) 350 °F (177 °C)
should be set as close as practical to the operating
Non-Lubricated 275 °F (135 °C) 325 °F (163 °C) temperature.
PRC 275 °F (135 °C) 325 °F (163 °C)
Hydrogen Rich 275 °F (135 °C) 300 °F (149 °C)

Maximum Allowable Working
The Ariel performance software will provide a red Pressure
flag if the discharge temperature exceeds the
The maximum allowable working pressure is the
maximum allowable discharge temperature
maximum continuous pressure for which Ariel
shutdown limit. A blue flag will be provided when
has designed the cylinder when handling the
the discharge temperature exceeds the
specified fluid at the maximum temperature.
application guideline, a warning as the discharge
Relief valves shall be provided and set to operate
temperature approaches the maximum
at no more than the Maximum Allowable Working
allowable level. A warning will also be displayed
Pressure. The MAWP is based upon the minimum
when the average of the suction temperature and
of the following considerations:
discharge temperature exceeds 285 F (140 C).
• Burst test pressure (adjusted by a safety
The discharge temperature calculated by current factor which is dependent on cylinder body
version of the Ariel Reciprocating Performance material)
Program, is based on suction temperature plus • Allowable bolt loading
cylinder pre-heat and internal compression ratio. • Flange rating
The equation is as follows: • Alternate cylinder bolting (17-4PH bolting).
Current cylinder MAWP are not reduced in

most cases when "Sour Gas" bolting is used. The Ariel DataBook lists gas rod load ratings for
The NACE MAWP are listed in the DataBook both current and inactive frames. Always check
for the exceptions (17-7/8K:T:C:D:Z:U Class the frame nameplate or contact the Ariel
cylinders). Response Center for the maximum allowable
The Ariel DataBook lists only current MAWP internal gas rod load when calculating
ratings. Many cylinders have been uprated over compressor performance for existing equipment.
time. Always check the cylinder nameplate for
the MAWP when calculating compressor
performance for existing equipment. Minimum Allowable Pin Load
Reversal
Maximum Allowable Internal Crosshead pin reversal is a reversal of
Gas Rod Load compression and tension loads at the crosshead
pin to connecting rod bushing. Without proper
Ariel gas rod load ratings are based upon reversing loads, the bushing will not be provided
calculated internal gas rod loads. The maximum with sufficient lubrication and bushing failure
allowable gas rod load of a given frame shall not will occur. Pin reversal is defined by two
be exceeded at any operating point. Refer to Ariel components, degrees and percent. These
Calculation Method for internal gas rod load represent the duration of the reversal and the
equations. magnitude of the reversal. Both of these values
must meet or exceed minimum values. Ariel’s
Gas rod load is best monitored for alarm and
requirements for reversal are 30 degrees of crank
shutdown with the use of a differential pressure
rotation, and 25% magnitude. The percent
switch across each cylinder at the flange
magnitude is defined by the smaller of the
(cylinder discharge pressure minus cylinder
tension or compression force divided by the
suction pressure). The performance software
larger of the two. The combined gas plus inertia
and the rod load charts from the DataBook are
loading at the crosshead pin is used for the
available to assist in determining the differential
reversal calculations. The inertia load
pressure settings.
component includes the weights of the piston
If the operating conditions are to include the and rod assembly, balance nut and crosshead
relief valve set pressure, the compressor gas rod with crosshead bushings.
load must be maintained within the gas rod load
limit, either by not exceeding the gas rod load
limit at relief valve set pressure or by applying a
shutdown switch on differential pressure across Some smaller frames are rated for lower reversal
the cylinder. The relief valve is meant to protect values, 30 degrees and 15%.
the pressure equipment from exceeding system
pressure ratings. Relief valve set pressures are
discussed in the Packager Standards Section 4.

Ariel’s Reciprocating Compressor Performance

Program provides the reversal values and will
flag upon insufficient reversal. A full review for
reversal will need to include the range of speed,
Single acting cylinders:
pressure and any single acting conditions. The
multi-run function is an invaluable tool in Single acting at lower compression ratios results
reviewing reversal values. in longer periods of gas rod load in compression.
At lower speeds reversal can be insufficient to
The ratio of compression to tension gas rod load
offset the gas compression load. Possible
can indicate reversal may be of concern. If
solutions include increasing the balance weight
compression gas rod load is much higher than
or limiting the lower end of the speed range.
the tension gas rod load, reversal may be a
concern and should be reviewed.
There are several specific situations and

configurations that should be reviewed in the
multi-run function across the full range of speed,
pressure, and load steps for sufficient reversal.
These include:
Maximum Allowable
High Pressure Service:
Reciprocating Weight
High pressure on smaller bore cylinders
Each compressor frame has a maximum
operating at lower compression ratios can see a
allowable reciprocating weight limit. This weight
notably higher compression gas rod load than
is based upon the total combined weight of the
that in tension. Possible solutions include
connecting rod assembly, crosshead assembly,
selecting a larger cylinder bore, selecting a tail
crosshead nut and piston / rod assembly. The
rod cylinder configuration, or increasing the
maximum allowable reciprocating weight limits
balance weight (crosshead and balance nut).
are included in the limitations set within the Ariel
performance program.
Reciprocating weight will affect the inertia load,

and therefore the combined rod load. Ariel
Tandem cylinders: publishes internal gas rod load limits, and
maximum allowable reciprocating weights,
Tandem cylinders may see sufficient reversal at
rather than combined rod load limits.
the maximum and minimum speed, while
insufficient reversal somewhere in between. Ariel's performance program will monitor
Adding balance weight will move this dip in the maximum reciprocating weights versus rotative
reversal curve, but not often completely out of speed and provide application limitations within
the operating speed range. Possible solutions the weight balance section.
include selecting a larger crank end cylinder bore
Refer to Ariel Corporation Electronic DataBook
(then add clearance if needed), increasing the
Cylinder Details for rotative speed limitations for
balance weight, or limiting operating speed.
the various frames and cylinder classes.

Rated Speed (Maximum Lack of adequate crosshead pin load reversal can
limit the minimum operating speed. An analysis
Allowable Rotating Speed) of the crosshead pin forces must also be
Each frame has a rated (maximum allowable performed to ensure that the proper amount of
rotating) speed. This is the highest allowable pin force reversal is present at all operating
rotating speed for continuous operation. The speeds and load steps.
driver overspeed shutdown must be set no Compressor valves are selected for a specific
higher than 10% over the rated speed of the operating condition with some flexibility for
compressor. variations for speed and operating conditions. A
Some large bore cylinders are limited to a general rule of thumb for valve selection is that a
maximum operating speed that is less than the single selection can be operated within a 2:1
frame rated speed. See the Ariel Corporation maximum speed range. Varying suction
DataBook cylinder details for rotative speed pressures, discharge pressures and gas analyses
limitations. can further limit this speed range. Low lift valves
may be necessary for speed ranges outside a 25%
See Also Rated Speed (Minimum Allowable variation.
Rotating Speed)
Speed ranges must be considered in the torsional
and acoustical analyses. Wider speed ranges in
Rated Speed (Minimum combination with wide ranges in operating
Allowable Rotating Speed) conditions and load steps may result in black out
speeds due to natural frequency interferences.
Many factors affect how slow the compressor can
All applications requiring rotative speeds that are
be operated. These include oil supply pressure
lower than one half the rated speed of the frame,
to the frame, crosshead pin load reversal, valve
must be reviewed by Ariel Corporation
dynamics, and torsional / acoustical
Applications Engineering.
considerations.
Also See:
Ariel Compressor frames are designed to have
adequate frame oil supply pressure down to one Frame Driven Lube Oil Pumps
half their rated rotating speed. If operation at
Rated Speed (Maximum Allowable Rotating
less than half speed is desired, the addition of a
Speed)
motor driven auxiliary lube oil pump is required
to maintain adequate lube oil pressure and flow.
The additional flow of the auxiliary oil pump will
maintain the frame oil pressure required for
proper operation. Removal of the main frame oil
pump is not necessary.

Maximum Allowable Piston Frame Horsepower Limits

Speed Ariel Compressor frames are not horsepower
limited. Ariel compressor frames are limited by
Ariel compressors are designed to be operated at
internal gas rod load. The published horsepower
full speed for most natural gas applications.
ratings are guidelines to be used in applying each
Slower piston speeds may be necessary based
compressor frame. The horsepower ratings may
upon the application. Factors that affect
be exceeded, as long as other application limits
lowering the operating piston speed include gas
are not exceeded. A torsional analysis should be
mole weight, higher discharge pressures, desire
performed to confirm vibratory torque limits are
for better efficiency and client preferences.
not exceeded.
Piston speed can be calculated with the
Some frames carry a power limit on each throw.
following equation:
This limit is flagged separately, and is speed
dependent. The KBK:T frame includes a power
per throw limit.
PS = Average Piston Speed, feet per minute Minimum Volumetric

This equation calculates average piston speed, Efficiency
which is the basis for piston speed related
ratings. Instantaneous piston speed is different, Volumetric Efficiency (VE) is the ratio of the
since the piston accelerates from zero velocity at actual delivered gas volume to the swept volume
the end of the stroke, and obtains a maximum of the cylinder. For additional information refer
velocity during the stroke. to the compressor theory
Some larger bore cylinders have limited piston The minimum allowable suction volumetric
speeds due to the higher inertia. For maximum efficiency for any cylinder end at a proposed
piston speed see individual cylinders in the operating point is 15%. These limits are set to
DataBook. allow proper valve dynamics.
For non-lube applications, allowable piston It is recommended to allow a usable margin to

speeds are reduced. See application guidelines this minimum VE for operation outside normal
for non-lube applications for more information. operating conditions. A 30% VE at normal
operating conditions will allow some margin for
unforeseen operating conditions or clearance
pocket usage.
Low volumetric efficiencies will result in higher

than expected discharge temperatures, higher
than expected horsepower per million and lower
than expected capacity. Low volumetric
efficiencies will result in poor valve dynamics
leading to possible early valve failure.

Discharge volumetric efficiency must be

measured in time rather than percent. Refer to
Figure: Theoretical vs. Actual VE
Discharge Event
for information and limits on discharge

volumetric efficiencies.
Pseudo-Q Value
(Courtesy Hoerbiger Corporation of America)
The "pseudo-Q value" is a term used at Hoerbiger

which is an indicator of the "adequacy" of a
valve. In other words, is there enough or too little
valve for the application?
The pseudo-Q value is a dimensionless value

developed by Hoerbiger and Ariel to indicate the Ariel and Hoerbiger require Pseudo-Q values
adequacy of a compressor valve. It is defined as between 1% and 15%
the average pressure drop through the valve • Pseudo-Q value less than 1%
divided by flange pressure, expressed as a If Q drops below 1%, it becomes difficult to achieve
percentage. The pseudo-Q value must be good valve dynamics, since the pressure drop which
the valve springs work against is too low and a tenden-
between 1% and 15%. With high and low pseudo- cy towards valve flutter is great. This is what is com-
Q values the compressor calculation model is not monly referred to as having “too much valve”. This can
able to accurately predict the horsepower losses, happen when compressing low molecular weight gas-
es (hydrogen, helium, etc.). The solution is to lower the
preheating of the gas during the intake event or valve lift, lowering lift area and equivalent area, and
the volumetric efficiency (capacity). creating a larger pressure drop across the valve.
• Pseudo-Q value greater than 15%
On the suction valves the Q - value is the pressure
If Q is 15% or higher, the pressure drop across the valve
drop across the valve in percent of line is too high for the cylinder pressure to recover to line
pressure: pressure at the end of the suction stroke. The valve
does not close at the end of the stroke as designed. Gas
backflows through the valve as the piston is beginning
the compression stroke, which slams the valve closed.
Volumetric efficiency is also reduced since the cylinder
does not have a full charge of gas (due to a backflow
out of the cylinder bore), in addition to the high horse-
power losses associated with the large pressure drop
across the valve. High q-values can occur when com-
where Ps = gas density pressing high molecular weight gases(CO2, propane,
etc.). In most cases, lift cannot be added to valve with-
Ps = suction pressure out sacrificing durability. Slower rotating speeds will
lower q-values by decreasing piston speed and gas ve-
V = mean valve velocity (calculated with locity through the valve. Selecting a different cylinder
equivalent area) may result in lowering the pseudo-Q value due to valve
flow areas differences., etc.).

Cooled Packings Cooling with oil is not as effective due to the

lower heat transfer ability and higher pressure
Figure: Packing Cooling Application Guidelines losses due to viscosity. In some circumstances,
oil can be used as a coolant in the packing cases.
This is limited to lower heat load conditions and
smaller compressor frames. The advantage of
applying oil cooling in the smaller frames, is the
ability to use frame oil, making it possible to cool
the packing case with the short coupled distance
piece. Oil will be taken from the frame oil system,
and returned internally, directly into the
crosshead guide.
Cooled packing cases are required for If one packing case is oil cooled on the smaller
compressor cylinders based upon the average frames, the oil will be taken from the pressurized
piston speed and average cylinder pressure. frame oil system. This is a closed loop and all
Cooled packing cases are supplied to help tubing provided by Ariel. If more than one
remove the heat generated as the piston rod/ packing is oil cooled, a separate oil loop will need
packing friction increases with the higher to be provided by the packager. Oil can be taken
pressures and piston speed. from the sump at the drive end of the frame,
through a pump, cooler, and into the packing.
Please refer to the Packager Standards Section 7:
The packing return will be internal, directly into
Cooled Packing for further information on this
the crosshead guide. Below is a schematic
topic. The following chart is an excerpt from the
showing oil cooling on more than one packing
Cooled Packing topic:
case.
Notes:
1. The Ariel Performance Software will indicate
when operating conditions fall within Region
2 or Region 3.
2. All forged steel cylinders have cooled packing
as standard and must be connected to a
cooling system.
3. All non lubricated cylinders have cooled

packing as standard and must be connected
to a cooling system.
4. Any deviation from the packing cooling

requirements must be reviewed and
approved by Ariel Applications Engineering
or Technical Services.

Non Intercooled
At times, more commonly with refrigeration
units, interstage gas cooling may not be
necessary due to low discharge temperatures
from the low gas k-value. Operating without an
interstage gas cooler can be done with special
considerations.
The suction temperatures to each stage, and

mean cylinder gas temperatures must be limited
as noted in the Suction Temperature topic.
All considerations for condensation must be

reviewed and confirmed to avoid condensation
at the interstage. Condensate considerations
include periods of shutdown / cool down and
compressor cylinder lube oil carry over.
Interstage liquid removal should be considered.
A bottom suction cylinder arrangement may be

possible on some applications to allow
interstage piping routing from the top of one
stage to the top of the next stage, avoiding areas
that can trap liquids on the interstage.
All non-intercooled applications must be

reviewed and approved by Ariel Mount Vernon
prior to quotation.

Capacity and Load Control

The pressure and flow conditions for which the lower gas velocities creating lower valve and
compressor is designed and/or operated can cylinder losses.
vary across a wide range. The three primary 2. The addition of clearance will reduce
reasons for changing the capacity of a capacity and required power through a
compressor are process flow requirements, decrease in the volumetric efficiency of the
suction or discharge pressure management, or cylinder. Methods of adding clearance are
load management due to changing pressure the following:
conditions and driver power limitations. Several
• High Clearance Valve Assembly
methods can be used to reduce the effective
capacity of a compressor. The “best practice” • Variable Volume Clearance Pockets
order of the unloading method is included in the • Pneumatic Fixed Volume Clearance
Pockets
table below.
• Double Deck Valve Volume Pockets
Preferred Order of Unloading Method 3. Single acting cylinder operation will reduce
Required Action Method Of Unloading
capacity through cylinder end deactivation.
Cylinder head end deactivation can be
Reduce Flow 1 Reduce Speed
2 Add Clearance
accomplished by removing the head end
3 Single Acting Cylinders suction valves, installing head end Suction
4 Bypass to Suction Valve Unloaders, or installing a head end
5 Throttle Suction
Pressure
bypass unloader. Refer to Single Acting
Cylinder configuration for further informa-
Reduce Torque 1 Add Clearance
2 Single Acting Cylinders
tion.
(speed dependent)
3 Throttle Suction
4. Bypass to suction is the recycling (bypassing)
Pressure of gas from the discharge back to suction.
Maintain Suction or 1 Reduce Speed
This reduces the downstream capacity.
Discharge Pressure 2 Add Clearance Bypassing gas from discharge back to
3 Bypass to Suction suction does not reduce the power consump-
4 Single Acting Cylinders
5 Throttle Suction
tion (unless fully bypasses for zero flow
Pressure downstream).
5. Suction throttling (artificially lowering the

1. The use of driver speed for control can be one
suction pressure) reduces the capacity by
of the most effective methods for capacity
lowering the actual flow into the first stage
reduction and suction and/or discharge pres-
cylinder. Suction throttling can reduce
sure management. The available power of
power consumption, but may have an impact
the driver will decrease as the speed is
on the discharge temperatures and rod loads
decreased. The compressor power efficiency
generated by the higher compression ratio.
increases as the speed decreases due to

Application Manual – Capacity and Load Control 12/13/2023
Capacity control methods can have an impact on

various performance characteristics besides flow
and power. Partial load conditions should be
reviewed for acceptable performance including
valve lift selection and dynamics, volumetric
efficiency, discharge temperatures, rod reversal,
gas rod loads, torsional and acoustical response.
Automated capacity control sequences must be

communicated so that the same set of loading
steps is considered in the acoustical analysis,
torsional analysis and control panel logic.
Compressor valves are selected to have optimum Most compressor cylinders can be equipped with
dynamic motion at one operating condition, and variable volume clearance pockets. The VVCP is
have some flexibility for off conditions. A general mounted in place of the head end cylinder head.
rule of thumb for speed impacts on valve The VVCP includes an adapter, piston, seal ring,
dynamics is that a single valve selection can be stem, Teflon vee packing, turning handle and
operated with a 2:1 maximum speed range. locking wheel.
This may be limited with a minimum speed.
Operation below half frame rated speed may see The expected change in compressor flow and
reduced valve life. Varying suction pressures, absorbed power will depend upon the
discharge pressures and gas analyses can further application compression ratio and the properties
limit this speed range. Low lift valves may be of the gas being compressed. Always check to see
necessary for speed ranges outside a 25% that the head end suction volumetric efficiency
variation. When applying variations in speed and or discharge event are within limit when setting
single acting cylinder configurations the the pocket.
torsional and acoustical response analysis will be To set the VVCP at the desired percentage open,
much simplified by applying single acting fully close the VVCP, and then fully open it,
configuration only at one given speed. counting the number of turns to the full open
position. Fully close the VVCP. Multiply the
Variable Volume Clearance number of turns by the desired percentage open,
and turn the VVCP open the resulting number of
Pockets turns.
A VVCP is used to change the clearance volume of The pocket position can be measured with a ruler
the head end of a cylinder. The amount of on site. A pocket position nameplate is attached
clearance will vary depending upon the position to newer pockets showing the measurements for
of the clearance pocket piston. Clearance is open and closed. This data can also be found in
added to the cylinder by turning the piston / stem the Ariel Performance Software.
assembly counter clockwise (CCW).

Refer to the compressor cylinder DataBook for

available VVCP for each cylinder.
The vent on the VVCP will be one of two

configurations. K, T, C, D, F, U, Z cylinder classes
with models 8-3/8 and larger, will have two seals
on the stem with a vent between. All other
cylinder classes will have a vee packing for the
stem seal and a vent downstream. Refer to the
Packager Standards for information on routing The cylinder DataBook lists the number of high
these vents. clearance assemblies that can be provided with
each cylinder and the percent of added fixed
clearance for each assembly. A new cylinder
purchased with high clearance assemblies will
also be supplied with standard valve retainers.
Cylinders of the class 3SG-CE and 3-5/8SG-CE

show the availability of high clearance valve
assemblies in the performance software. These
cylinder classes do not use the traditional
spacers as shown above, but utilize high
clearance crank end head designs to add the
clearance. The clearance defined for these
cylinder classes are machined as part of the
cranks end head and are not removable valve
spacers.
High Clearance Valve Hanging guard design valves cannot be outfitted
Assembly with high clearance valve assemblies. Gas flows
around the circumference of these valves.
A high clearance valve assembly is used to Installing a spacer would block the gas flow.
increase the fixed clearance volume of a cylinder
end. A high clearance assembly is comprised of a Below is a drawing of a hanging guard design
valve spacer, a special retainer, and a gasket. The valve.
spacer is placed between the cylinder valve seat
and the valve body.

Suction Valve Unloaders

Also see: Clearance Volume
See Cylinder Action, Single Acting for a drawing
of a suction valve unloader installed on a
Pneumatic Fixed Volume cylinder.
Clearance Pockets A valve plate depressor type suction valve
unloader will depress the suction valve plate
A FVCP is used to add clearance volume to the
against the valve guard to hold the valve open,
head end of a cylinder. A plug is pneumatically
therefore deactivating the end of the cylinder by
actuated to either fully open or fully close the
allowing gas to pass through the valve during
pocket. The FVCP assembly is mounted in the
both intake and compression stroke. A valve
head end of a cylinder.
plate depressor type suction valve unloader is
actuated using air or natural gas as actuation gas
(usually 70 to 100 psig). In most cases, the suction
valve unloaders are normally loaded, with air or
gas actuation pressure required to unload the
cylinder end. Suction valve unloaders may be
used only on plate or ring valves (not poppets).
The FVCP requires 80-100 psi of air or gas

pressure to operate. Actuation of the pocket can
be performed by the PLC controlling a solenoid
valve. In most cases, the FVCP is normally
unloaded (FVCP open), requiring air or gas
pressure to load (FVCP closed).
Data regarding FVCP designs and availability for

each compressor cylinder is available in the Ariel
Electronic Databook.

Applications that require suction valve unloaders An alternate method of single acting a cylinder is
must be reviewed by Ariel / Hoerbiger before by removing the head end suction valves on one
quoting. The valve depressors are always in the cylinder end. Suction valve removal will result in
seat flow passages. This will reduce the valve less horsepower loss as the unloading flow area
equivalent area and increase the horsepower is greater. Cylinders with suction pressures
losses of the valve. Temperatures may also be above 750 psi and or small valve sizes may not be
increased due to a recirculation of the gas on the suitable for suction valve unloaders.
deactivated end preheating the active end. It is
important that data regarding the entire range of
suction pressures and gas compositions be Head End Bypass Unloaders
submitted for review. The review will specify the
valve plate materials, lifts and valve equivalent
flow areas to be used for the application. Suction
valve unloaders must be installed on all suction
valves of the end being deactivated.
Ariel recommends using suction valve unloaders

on the head end of cylinders only. Crank end
deactivation may result in a non-rod load
reversal situation. All deactivation
configurations should be analyzed at all
conditions to verify adequate rod load reversal.
Single acting cylinder operating cases should be

considered when analyzing torsional responses
and acoustical pulsation responses. Single
Acting cylinders can present the worst case
scenario for a torsional analysis due to a more
dynamic torque effort curve and for an acoustical
pulsation analysis due to a change in the number
of pulses per cycle. High torsional vibration and /
or high acoustically driven vibration can result
High torsional vibrations can increase coupling

and shaft stresses, driver functionality and
auxiliary driven equipment integrity. High
acoustical pulsations can increase frame,
cylinder, gas piping and equipment vibrations.

Head end bypass unloaders are pneumatically Single acting cylinder operating cases should be
actuated ports on the head end of the cylinder considered when analyzing torsional responses
that allows the head end compression to be open and acoustical pulsation responses. Single
to the suction gas pressure. This fully deactivates Acting cylinders can present the worst case
the head end of the cylinder for single acting scenario for a torsional analysis due to a more
configuration. Head end bypass unloaders are dynamic torque effort curve and for an acoustical
most often applied when the suction pressure is pulsation analysis due to a change in the number
higher than suction valve unloaders can be of pulses per cycle. High torsional vibration and /
applied (near 1000 psi and higher). or high acoustically driven vibration can result
The pneumatic actuator is smaller, to fit within
the unloader, so requires a higher actuation
pressure, often in the few to several hundred psi High torsional vibrations can increase coupling
range. Each application and cylinder size will and shaft stresses, and affect driver functionality
require a specific actuation pressure. These can or auxiliary driven equipment integrity. High
be found in the Ariel performance software on acoustical pulsations can increase frame,
the device datasheet. cylinder, gas piping and equipment vibrations.
Most often, process gas can be regulated from a An alternate method of single acting a cylinder is
higher pressure stage discharge to the by removing the head end suction valves on one
appropriate pressure and applied as the cylinder end. Suction valve removal will result in
actuation gas. The actuation gas must be clean less horsepower loss as the unloaded flow area is
and dry. Sour gas cannot be used as actuation greater. Cylinders with suction pressures above
gas (greater than 100 ppm H2S) for safety 1000 psi and or small valve sizes may not be
reasons. If the process gas contains hydrogen suitable for suction valve unloaders.
sulfide, nitrogen may be used for the actuation
gas.
Double Deck Volume Pockets
Actuation gas must be clean and dry. When
regulating the higher pressure supply stream to
the required actuation pressure, a liquid
collection / separator device must be installed
directly downstream of the regulator.
Head end bypass unloaders may not be as

efficient as suction valve unloaders, but can be
applied at higher suction pressures.
All deactivation configurations should be

analyzed at all conditions to verify adequate rod
load reversal.

A double deck volume pocket is used to add close to allowing full compression on the last
clearance volume to the end of a pipeline stage the valves can flutter during this blowthru
cylinder through the valve port. An unloader condition. Blowthru is acceptable if the unit will
assembly is pneumatically actuated to either not operate at extended periods of time at this
fully open or fully close the pocket. The volume condition.
pocket assembly is mounted in the valve port of
If the unit will operate at this lower ratio for
the cylinder.
extended periods a stage of compression can be
The unloader requires 80-100 psi of air or gas deactivated, or taken out of service. For shorter
pressure to operate. Using a solenoid valve, it can durations the cylinder can be deactivated by
be operated by electronic signals from a flow removing all suction and discharge valves from
computer or PLC. In most cases, the pocket is both ends of all cylinders on the deactivated
normally unloaded with air or gas pressure stage. Extremely short durations may see only all
required to load (close the pocket) the cylinder. suction valves removed to lower valve removal
time, but will result in more power usage and
Contact Ariel Corporation for availability and
higher temperatures. For longer periods the
data regarding double deck volume pocket
stage can be deactivated by removing all valves,
applications.
removing the piston and rod, rerouting the
cylinder and packing lubrication to the frame,
Deactivated Stage replacing the packing with a solid plug and
rebalancing the reciprocating weights.
Every now and then a service changes to lower
pressure ratios and requires fewer stages of Any changes in operating conditions warrants a
compression on existing equipment. review of performance to ensure proper
Deactivating a stage can be accomplished with operation within allowable limits is maintained.
allowing blowthru or by physically deactivating a Changes in conditions requiring deactivating a
stage. Deactivated stage methods are not to be stage can have impacts to rod reversal, rod loads,
confused with deactivating a cylinder within a discharge pressure versus MAWP and potentially
multi cylinder stage (see Deactivated Cylinder torsional responses.
below). These "extended periods of time" should be
Blowthru occurs when the compression ratio defined by the user based upon frequency of re-
across the compressor is not high enough to activating the stage, acceptable maintenance
accommodate compression in all the available and the availability of manpower to change the
stages. The gas is compressed to full discharge unit configuration. In general, blowthru can be
pressure in the first several stages and physically tolerated for days to a few weeks. Deactivating
blows thru the last stage without further by pulling the suction valves can be tolerated for
compression. This blowthru gas flow holds the months. Deactivating by removing the piston
suction and discharge valves open. If the unit is and rod can be used for longer durations in the
terms of half a year and up. The duration of
deactivation by the blowthru and pulling suction
valves are discussed due to the likelihood of
higher maintenance if the durations are longer.

Blowthru conditions can cause the valves to this method, the gas will be recycled from head
open and close, without preferable dynamics, end to crank end through the suction gas
resulting in possible broken valves before the passages and will heat up. In most cases, the
next loading of the stage. Pulling the suction heat generated will be greater than the
valves and leaving the piston and discharge maximum allowable average cylinder
valves in place can also result in failure of the temperature of 285 F (140 C). If this methods is
discharge valves over time and will result in used, cylinder temperature measurements must
continued wear of the piston rings, wearbands be taken at the suction gas passages. The
and packing sealing rings. discharge temperature measurement location
will not read the cylinder gas temperature.
Deactivated Cylinder
Non-Acting Cylinders
Deactivating a cylinder that is part of a stage is
handled differently than deactivating an entire A non-acting cylinder is a cylinder that is
stage. An example would be if there are two first installed, but is not compressing gas. There are
stage cylinders and typical unloading methods several ways a cylinder would be non-acting.
are not enough, one first stage cylinder can be • Blowthru
deactivated while the other first stage cylinder • All Valves Removed
continues to compress. If an entire cylinder • All Suction Valves Removed
within a stage needs to be deactivated, this can • Piston and Rod Removed
be done in one of two ways; Removal of the • Blank Throw
piston and rod, or non-acting the cylinder. • Non-Acting for Startup
Removal of the piston and rod is the preferred Blowthru occurs when the compression ratio
method to deactivate a cylinder. This is across the compressor is not high enough to
accomplished by removing the piston and rod, accommodate compression in all the available
installing blank flange blinds between the stages. The gas is compressed to full discharge
cylinder and pulsation vessels (suction and pressure in the first several stages and physically
discharge), installing a plug in place of the blows thru the last stage without further
packing case, rebalancing and removing the compression. This blowthru gas flow holds the
cylinder lubrication from the deactivated suction and discharge valves open. If the unit is
cylinder. Removing the suction valves from both close to allowing full compression on the last
ends of the cylinder can be done rather than stage the valves can flutter during this blowthru
installing flange blinds. condition. Blowthru is acceptable for short
durations. Longer durations can lead to
An entire single cylinder, when part of a multiple
premature valve failure in the stage with
cylinder stage using a manifolded suction
blowthru.
pulsation vessel, can be deactivated by removing
the suction valves from both ends of the cylinder. All of the cylinder valves can be removed if a
This method is not recommended by Ariel, but stage of compression will need to be disabled for
has been performed successfully on specific an extended period of time. This allows a larger
installations. If this method is successful, it can flow area for the gas to pass through the cylinder
save down time for shorter term deactivation. In valve ports, reducing the pressure losses in the

stage. This also removes the valves from the cylinder. Removing the suction valves from both
wear life equation. Removing all of the cylinder ends of the cylinder can be done rather than
valves must be limited to deactivating an entire installing flange blinds. The definition of
stage, not just one cylinder of a mutli-cylinder "extended period" is determined by the end user
stage. and is a balanced of the time and equipment it
takes to accomplish the removal of the piston
All Suction valves can be removed from a cylinder
and rod against the savings for wear parts and
to disable a stage for much shorter periods.
lubrication.
Some of the benefits of lower pressure loss are
attained, while having a shorter downtime to Removal of the piston and rod is the preferred
remove valves. method to non-act a cylinder within a stage.
All Suction valves can be removed if a single Blank throws are locations on the frame that can
cylinder of a mutli-cylinder stage needs to be accommodate a cylinder, but are not mounted
disabled. Though this method is not with cylinders, ie., placing three cylinders on a
recommended by Ariel, it may be possible to non- four throw compressor. There are two different
act a single cylinder within a stage. In most balancing configurations for a blank throw, an
cases, non-acting a cylinder within a stage will active crosshead guide and a balancing
result in overheating the cylinder beyond the crosshead guide. An active crosshead guide is a
capabilities of the non-metallic components guide that can accommodate the mounting of a
within the cylinder. If this method is to be used cylinder and has standard crossheads and
for non-acting a cylinder within a stage, the balance nuts installed. A balancing crosshead
cylinder nozzle temperatures on the suction side guide, also referred to as a dummy guide, is a
(since suction valves are removed) must be special guide with added length to
closely monitored so as not to exceed 285 F (140 accommodate larger, special, balancing
C). This method has been known to work in some crossheads. Cylinders cannot be mounted on
specific circumstances, while in the greater balancing guides. When applying a blank throw,
majority is not successful. The cylinder to be the reciprocating weight is not offset by gas loads
non-acting must be part of a manifolded suction from compression. Therefore, the weight of the
vessel with the other cylinder(s) active. blank throw should be minimized by mounting
the smaller of the cylinders on the opposing
Removal of the piston and rod to disable a stage
throw. Throws are locations on the frame that
can be done when the unit will operate with a
can accommodate a cylinder, but are not
disabled stage for extended periods of time.
mounted with cylinders, ie., placing three
Removal of the piston and rod allows the
cylinders on a four throw compressor.
wearing components to be removed and the
cylinder lubrication to be shutdown for the Cylinders can be non-acting for start up
cylinder. This is accomplished by removing the purposes. When the available starting torque is
piston and rod, installing blank flange blinds not available for a fully bypassed compressor
between the cylinder and pulsation vessels start, unloading ends of the cylinders will help
(suction and discharge), installing a plug in place reduce some of the starting torque. This will
of the packing case, rebalancing and removing require the use of suction valve unloaders or
the cylinder lubrication from the deactivated head end bypass devices. Actuating suction

valve unloaders on the head end can help reduce

the staring torque. In some cases, the motor
inrush current must be further limited; suction
valve unloaders can be applied to both the head
end and crank end to further reduce the starting
torque. When both ends are non-acting for start
up, a time limit of five (5) minutes should be
applied for the non-acting duration.

Distance Piece Purge and Vent Arrangements for Sour,

Corrosive and Hazardous Gasses
Ariel provides suitable materials options and Packing Leakage
configuration options for a successful packing
vent system. Much of the success of a packing Piston rod packing is designed to seal against
vent system falls on the End User and Packager cylinder pressure, but are dynamic seals and will
for design of the packing vent system and the End have some leakage. This leakage will increase
User for operations and maintenance of the over time due to wear of the non-metallic sealing
system. rings. The packing case is made up of several seal
sets, each seal breaking down the pressure
further than the last. In the new and broken in
Options condition packing rings will leak some gas. The
leakage rate will depend upon the condition of
Materials options are available for key
the packing and to some extent the use of a purge
components in the gas stream for sour and
gas (see purge packing).
corrosive gasses. Materials options for
components such as piston rods, valves, cylinder Packing in the new and broken in condition will
bolting, bearings, tubing and tube fittings are leak 5-10 SCFH through the vent with 2-3 SCFH
discussed in the Ariel Sour Gas topic. entering the distance piece. Prior to break in
leakage will be higher.
Configuration options are available including
purged pressure packing cases, short and long When purged packings are employed the packing
two compartment distance piece arrangements, will leak 8-13 SCFH through the vent due to the
flushing oil system and separate lube oil addition of the purge gas and 3-5 SCFH of purge
arrangements for the cylinders. These are gas entering the distance piece. The purge gas
discussed in the Ariel Sour Gas topic. demand will be roughly 5 SCFH.
When a long two compartment distance piece As the packing wears out vent leakage will
and purge packing is purchased the intermediate increase to as high as 120-180 SCFH (2-3 SCFM)
and wiper packing cases come with purge rings and purge gas may increase up to 30 SCFH to
and purge gas connections. These are available maintain a positive pressure over the vent
for incorporation into the system design. pressure. Likewise, distance piece flows will
increase respectively.
The KBE:K:T and KBZ:U are not offered with a
short two compartment option. The long single Upon shutdown of the compressor packing
compartment design incorporates a purged leakage will continue, and increase, unless
wiper seal set when purged packing is cylinder pressures are relieved.
purchased.
Refer to the Packager Standards Section 8
Refer to the Packager Standards Section 8 Packing and Distance Piece Vent Systems for
Packing and Distance Piece Vent Systems for further information on vent systems.
further information and schematics on this topic.

Application Manual – Distance Piece Purge and Vent Arrangements for Sour, Corrosive and Hazardous Gasses 12/13/2023
Purged Pressure Packing Purge and Vent Arrangements

Cases Ariel provides suitable materials options and
configuration options for a successful packing
Purge packing refers to a packing case modified
vent system. Much of the success of a packing
to accept an external purge pressure 15 to 20 psi
vent system falls on the End User and Packager
above the primary packing vent/drain pressure
for design of the packing vent system and the End
with no more than 5 psi external system back
User for operations and maintenance of the
pressure. The purge gas must be sweet natural
system.
gas or an inert gas, such as nitrogen. The purpose
of purge gas is to block and contain hazardous, Options
toxic, flammable or corrosive gases, and to
prevent such from entering the compressor Materials options are available for key
frame where damage to the running gear, or components in the gas stream for sour and
personnel safety hazards can occur. corrosive gasses. Materials options for
components such as piston rods, valves, cylinder
Figure: Compressor Rod Pack 3500-2000 PSIG with bolting, bearings, tubing and tube fittings are
Purge Two Compartment Guides
discussed in the Ariel Sour Gas topic.
Configuration options are available including

purged pressure packing cases, short and long
two compartment distance piece arrangements,
flushing oil system and separate lube oil
arrangements for the cylinders. These are
discussed in the Ariel Sour Gas topic.
When a long two compartment distance piece

Packing case materials are cast iron and steel. and purge packing is purchased the intermediate
When steel is used, it is heat treated to be in and wiper packing cases come with purge rings
compliance with NACE. Garter springs are 316 and purge gas connections. These are available
stainless steel, for both sweet and sour for incorporation into the system design.
applications (acceptable for sour service based
upon acceptable field experience). The KBE:K:T and KBZ:U are not offered with a
short two compartment option. The long single
Please refer to the Packager Standards Section 8 compartment design incorporates a purged
Packing and Distance Piece Vent Systems for wiper seal set when purged packing is
further information on this topic. purchased.
Refer to the Packager Standards Section 8

Packing and Distance Piece Vent Systems for
further information and schematics on this topic.

Drivers
a JGD frame could be used for an application
were 60Hz electricity is available, an electric
driver could run the JGD at 1200 RPM for a piston
Electric Motor Drive speed of 1100 fpm, or run the JGC at 900 RPM for
Electric motors, direct connected through a a piston speed of 975 fpm. The JGC selection
flexible coupling can be utilized to drive Ariel would be more efficient and would have longer
compressors. Electric motors are available at times between scheduled maintenance due to
various speed depending upon the frequency of the slower piston speed. The JGC will also have
the power supply and the number of motor slightly larger cylinders. Common motor speeds:
poles. • Synchronous rpm = Power Frequency (hz) x
120 / number of motor poles
When the selection permits, it can be beneficial • Induction motor rpm = synchronous rpm x
to match an electric driver with the compressor 0.985 (accounts for 1.5% slip)
frame that will provide a lower piston speed. • Induction motors will operate at less than the
Slower piston speeds can provide higher rated synchronous speed because of “slip”. A
efficiencies and a longer time between typical motor slip is 1.5%. This must be
scheduled maintenance. For example, if a JGC or accounted for in the compressor selection.
Number of Motor
Synch Induction Synch Induction
Poles
50 hz 50 hz 60 hz 60 hz
4 1500 1475 1800 1775
6 1000 985 1200 1185
8 750 740 900 885
10 600 590 720 710
12 500 492 600 590
14 428 422 514 506
Electric motor drives will require a review of Ariel requires an additional 10% margin for
starting torques to ensure the motor has enough selection purposes to be included in the Rated
torque to start the rotation of the compressor. power of the motor. Service factor is not to be
This will most often require a full bypass for considered to cover this 10% margin. This is a
start-up and may require special motor torques. selection and sizing criteria; once installed the
Variable speed drivers have other details to full available driver power may be applied. The
consider, see Minimum Allowable Rotating 10% sizing margin is intended to cover Ariel's
Speed topic. prediction tolerances (+/-3% or +/-6%),
acoustical resonance impacts, motor
efficiencies, power supply cleanliness, and a

Application Manual – Drivers 12/13/2023
small portion of differences in operating • +10% of max horsepower for nameplate

condition (winter gas temperatures, etc). This power (Service Factor is not to be used to
conservative sizing approach is to avoid a meet this 10% margin requirement.)
package that may be restricted due to higher • The motor stub shaft and the section through
than expected electric motor power usage. the drive end bearing should equal or exceed
the compressor drive stub diameter.
Refer to the Ariel Packager Standards Section 5 JGE:K:T/6 and KBB:V frames have flanged
for more details on the drive system. drive end connections on the crankshaft, use
the crankshaft journal diameter for the
Ariel Performance Software provides the minimum motor shaft diameter. Crankshaft
necessary information for motor sizing, such as diameters can be found in ER-83, Frame Data
start up torque, torque effort curve, compressor Sheets and Torsional Supporting Documents.
inertia, and power demand. Studies necessary
Common Project information for motor driven • Motor start up analysis - Does the motor have
applications include: enough torque to reach full speed fast (before
the high inrush current overheats the motor)
Quotation • This is done by the motor supplier and
• Start up torque curve (at highest suction requires the compressor inertia value
pressure) with estimated bypass line pres- from the start up curve or mass elastic
sure losses data, the coupling inertia, inertia from
• Full horsepower torque effort curve any added flywheel or crankshaft detuner
• Part load torque effort curves (highest power • Current pulsation analysis
of each single acting step) • Torsional analysis
• +10% of max horsepower for nameplate • Lateral analysis may be necessary depending
power (Service Factor is not to be used to upon lengths
meet this 10% margin requirement.) Data necessary for Torsional from Motor
• The motor stub shaft and the section through Supplier
the drive end bearing should equal or exceed
the compressor drive stub diameter. • Mass elastic data (inertia and shaft stiffness)
JGE:K:T/6 and KBB:V frames have flanged • Shaft detail drawing for vibratory stress
drive end connections on the crankshaft, use calculations
the crankshaft journal diameter for the • Minimum additional inertia (flywheel) to limit
minimum motor shaft diameter. Crankshaft current pulsations
diameters can be found in ER-83, Frame Data
Sheets and Torsional Supporting Documents. *Generating Final Start Up Torque Curve
• Run start up curve at highest suction pressure
Purchase (confirming quotation data)
(or settle out pressure) and default pressure
• *Start up torque curve (at highest suction loss settings of 25 psi times the number of
pressure) with actual bypass line pressure stages
losses • Load cylinders if manual capacity devices are
• Full horsepower torque effort curve used, and unload cylinders if pneumatic
• Part load torque effort curves (highest power capacity devices are used (suction valve
of each single acting step) unloaders and pneumatic pockets)
• Apply the "flow at startup" value from the
start up torque data to size the bypass line

Application Manual – Drivers 12/13/2023
• Calculate the bypass line pressure drop at the

"flow at startup" (from final stage cylinder
discharge flange through vessels, coolers,
bypass line, bypass valve, suction scrubber,
suction vessel to first stage cylinder suction
flange)
• Provide the final flywheel inertia from the
torsional analysis and current pulsation anal-
ysis for the final start up torque calculation
• Rerun the start up curve with the calculated
bypass line losses
Start up torque is used to determine if an engine
starter, or electric motor driver has enough
torque to start a compressor. Refer to Starting
Torque topic for more specific information on
starting torque curves and data.

Process Application Definition

Process compressors are typically used in Excluded from Process Definition:
petroleum, chemical and gas industry services • Lubricated natural gas services
for handling process gas with either lubricated or • Lubricated fuel gas boosters with up to 50%
non-lubricated cylinders. These are moderate hydrogen
speed compressors meeting the demands of API- • Lubricated refrigeration
618 for critical service. API-618 has defined these • Lubricated air, nitrogen or carbon dioxide
compressor applications as having and expected • Non-lubricated fuel gas boosters
uninterrupted operation of at least 3 years as a
design criteria.
Process Equipment Selection
Process Compressors are separated from Oil and
Gas compressors by function and required Process Frames: JGA: JGJ: JGK: JGT: JGD: JGF:
maintenance intervals. Oil and Gas compressors KBU: KBB
are commonly driven by natural gas fueled Process Cylinders: JG: RJ: K: T: D: F: U: B
engines with major maintenance intervals of up
to 18 months with regular preventative
maintenance at every three months. Process Required Equipment for Process Offerings:
compressors are generally electric motor driven
• Wearbands with a 5 psi piston and rod
and require a target of 3 years between any
loading
maintenance.
• Ion nitrided cylinder bores
Ariel has developed a line of compressors to • Helium leak testing of cylinders in applica-
meet the demands for longevity and reliability tions less than 12 MW
dictated within API-618. This includes moderate • Long two compartment distance pieces (API-
rotating speed application, low average piston 618 Type C)
speeds, low piston wear band loading and • Purged and water cooled packing with
lapped packing cups
process gas emissions control capabilities.
• Purged intermediate and wiper packing
For applications guidelines on the Ariel Process • Indicator taps on cylinders
Compressor refer to the Process Table of
Contents.
Optional Equipment Available for Process
Offerings (typical additions)
These applications generally include any gas • Non-lubricated cylinder design
compressor application in: • Suction valve unloaders
• Refineries • Tungsten carbide piston rod coating
• Petrochemical Plants • BICERA crankcase doors
• Chemical Plants • Stainless steel tubing with stainless steel
• Industrial Gas Facilities fittings
• Material certification

Application Manual – Process Application Definition 12/13/2023
Process Piston
Capacity and Power Guarantee Tolerances The Process piston includes wearbands designed
within the Reciprocating Packager's Standard for a 5 psi loading suitable for both lubricated
Section 2. and non-lubricated services. The piston ring and
wearband materials are chosen to suit the
Process Frame Cyl Design Process gas, pressures and temperatures of each
service.
Ariel Process Frames include the JGA, JGJ, JGK,
Larger class cylinders utilize two wearbands
JGT, JGD, JGF, KBU and KBB. These frames offer:
located outboard of the piston rings while
• Shorter stroke to allow for wearbands for a 5 smaller cylinder classes have one wearband on
psi loading for lube and non-lube services
the outboard end of the piston. The cylinder bore
• Shorter stroke to allow for added piston rings
has been extended to allow for the travel of the
for hydrogen compression and non-lube
services wearbands.
• Forged steel crankshafts Figure: PRC Pistons
• Forged steel connecting rods
• Long two compartment distance pieces per Double Wearband
API-618 Type C
• Piston speed limitations to meet most
Process applications
Ariel Process Cylinders include the JG, RJ, K, T, D,

F, U and B cylinder classes. These cylinders offer:
• Wearbands to meet 5 psi loading for both
lubricated and non-lubricated services
• Wearband overtravel less than 50%
• Piston design to offer ring design and quan-
Single Wearband
tity sufficient for low molecular weight gases
whether lubricated or non-lubricated
• Indicator connections
• Purged packing cases
• Water cooled packing cases
• Application specific valve design
• O-ring sealed valve covers
• Capacity and Load Control devices available
• 4100 series alloy carbon steel piston rods
with ion nitride and optional tungsten
carbide coating
• Ion-nitrided cylinder bore
Piston rod materials for Process Applications are:

Application Manual – Process Application Definition 12/13/2023
Service Material Coating
Non Corrosive Lubricated 4100 Series Carbon Steel Ion Nitride
Non Corrosive Non-Lubricated 4100 Series Carbon Steel Tungsten Carbide
Corrosive 17-4PH Stainless Steel Tungsten Carbide

Lubricated and Non-Lubricated
Process Rotative Speeds

Process rotating speeds are conservatively set to
meet the design philosophy within API-618 for a
target of 3 years uninterrupted operation. The
maximum rotating speeds, and resulting piston
speeds, are listed below.
Process Frame Maximum Speed
Rotative Speed Piston Speed
Frame Stroke rpm fpm m/s
JGA 3.00 1200 600 3.05
JGJ 3.50 1200 700 3.56
JGT 4.50 1000 750 3.81
JGK 5.50 750 688 3.49
JGF 5.00 900 750 3.81
JGD 5.50 750 688 3.49
KBU 5.75 750 719 3.65
KBB 7.25 600 725 3.68
Process Motor Sizing Refer to Electric Motor Drive topic for information
on what information is needed for quoting,
The main motor driver for Process compressors purchasing and performing studies for electric
will typically be a direct coupled electric drive compressors.
induction motor or direct coupled electric
Motor driven reciprocating compressors typically
synchronous motor. Motor nameplate
require a torsional response analysis, current
horsepower must be 10% greater than the
pulsation analysis and starting torque analysis.
maximum operating horsepower or greater than
These studies will determine final coupling
the discharge relief valve set point condition,
selection and if a flywheel is required.
whichever is greater.

Quality Assurance Programs

EN 10204:2004 specifies the different types of
inspection documents supplied to the
purchaser... There are several categories or
ISO 9001 Certification Types referenced within EN 10204:2004. Below
Since 1995, Ariel Corporation has followed ISO's are excerpts from EN 10204:2004 and Ariel's
strategic tools and guidelines to ensure that our position on these categories.
products and services are consistent, safe, and Type 2.1 non-specific inspection: inspection
reliable. carried out by the manufacturer in accordance
Please refer to the Ariel website for further with his own procedures to assess whether
specifics on our ISO 9001 certification. products defined by the same product
specification and made by the same
manufacturing process, are in compliance with
Materials Certifications and the requirements of the order or not.
Tests A type 2.1 requirement would consist of a
certificate of compliance written by Ariel with no
Ariel's compressor components are purchased
inclusion of material test certificates.
and machined in large quantities, often in lot
quantities. Raw materials suppliers are audited Type 2.2 specific inspection: inspection carried
for their quality control and performance. These out, before delivery, according to the product
suppliers provide certain lot sample testing to specification, on the products to be supplied or
verify materials chemical compositions and / or on test units of which the products supplied are
physical properties. With the large quantity of part, in order to verify that these products are in
components purchased each year Ariel does not compliance with the requirements of the order.
require these materials certifications, but rely on
Ariel does not provide certification to Type 2.2.
the suppliers quality control system and the
auditing process. This system maintains supplier Type 3.1 Document issued by the manufacturer
quality while limiting component costs and in which he declares that the products supplied
coordination. are in compliance with the requirements of the
order and in which he supplies test results. ... The
An Inspection and Test Plan has been prepared to
document is validated by the manufacturer's
show what Ariel and Ariel's suppliers provide for
authorized inspection representative,
materials certifications. This list includes those
independent of the manufacturing department.
tests listed as optional in the Ariel Price Book.
Additional testing requests must be reviewed Ariel provides an option for Type 3.1 material
and approved by Ariel. Material certification with certificates for the crankshaft and cylinder body.
traceability are an available option for the These must be requested with the original
crankshaft and cylinder body. equipment purchase order.

Application Manual – Quality Assurance Programs 12/13/2023
Type 3.2 Document prepared by both the Assembly Inspections And

manufacturer's authorized inspection
representative, independent of the Tests
manufacturing department and either the During the assembly process, all units are
purchaser's authorized inspection subjected to a series of inspections to ensure
representative or the inspector designated by mechanical soundness (reference ER-5.3). These
the official regulations and in which they declare include:
that the proucts supplied are in compliance with
• Measurement and recording of critical values
the requirements of the order and in which test
such as crankshaft end clearances,
results are supplied. connecting rod side clearances, rod runout,
Ariel does not provide certification to Type 3.2. and bearing jack clearances.
• Check operation of lubrication system
components including shutdowns, pump(s),
Cylinder Leak Test passages and fittings.
• Verify critical torque values.
All Compressor cylinders are hydrostatically • Check freedom of movement of crankshaft
tested prior to shipment. The cylinders are tested and connecting rod pins.
at a minimum of 1 hour at 1.5 times the rated
All mechanically complete units (excluding
MAWP of the cylinder (Maximum Allowable
valves) are to be run tested for at least 4 hours,
Working Pressure). The hydrostatic test pressure
during which time operating parameters will be
is recorded on a pressure test recorder vs time
monitored and recorded on the Production Test
and retained with the permanent unit file.
Log (ER-5.3.1).
Cylinder hydrotests may be observed by the
After the run test additional inspections are
client if required. Requests for witness must be
performed on the unit including:
included at the time of order for scheduling
purposes. • Measure and record temperatures of main
bearing caps and connecting rods (at split
For lighter gasses, mole weights below 12 or lines), within 5 minutes of completion of run
hydrogen content above 50%, cylinders will be test.
leak tested with helium. Once the cylinder has • Visually inspect bores, piston rods, crosshead
been hydrotested , the cylinder is submerged in a shoes and slides for any scoring or unusual
wear patterns.
water tank and pressurized with Helium to the
• Crankshaft end clearances are measured and
cylinder MAWP or 2000 psig , whichever is lower.
recorded.
Pressure must be maintained and no leaks
• Critical torques and set screws are checked
observed for a period of thirty (30) minutes. and adjusted when required.
Helium leak tests of compressor cylinders is • After passing all previous inspections the unit
available as an option. is prepared for shipment. Final visual checks
of unit and associated paperwork is
Helium testing is required for gasses 12 mole
performed by Quality Control.
weight and below as well as gasses with 50% or
more hydrogen by volume.

Studies and Analyses

Start up torque is characterized by two main
components, break away torque and speed up
torque. The break away torque is the static
Unbalanced Forces and friction and gas load on the piston rod area at
Couples zero rpm. The speed up torque is the dynamic
friction and the pressure load on the cylinders as
Reciprocating compressors develop unbalanced the unit speeds up toward full speed.
forces and couples due to tolerances in the
reciprocating weights at the offset of the Ariel provides start up torque data within the
compressor throws. The unbalance comes in the Ariel Performance Program. All start up torque
form of horizontal and vertical forces and calculations provided assume that a bypass or
horizontal and vertical couples. gas recirculation line is installed and open, sized
to bypass 100% of the compressor flow.
The compressor skid and foundation must be
designed to dampen and transfer these forces. The break away torque is dependent on the
pressure on the unit when the start button is
All Forces and Couples act about the center of the pushed. Higher start up pressures will result in
crankshaft. higher break away torque. If the break away
Related topic: Balanced Opposed Design torque must be reduced for starting, the pressure
on the unit must be reduced. Six throw units are
mostly exempt from this as the phasing of the six
throws offers a cancellation of the individual
throw torques from the pressure on the piston
rod.
The speed up torque can be impacted by both

the starting pressure, as well as the bypass line
pressure loss. Smaller bypass lines will have
higher pressure losses, resulting in higher
torques as the unit approaches full speed.
Starting Torque Start Up Torque Calculations:

Start up torque is used to determine if an engine • Use the highest suction pressure that the unit
starter, or electric motor driver has enough will see when the start button is pushed. This
torque to start a compressor. may be a normal (max) suction pressure, or a
settle out pressure.
• Load all manual capacity devices (close
VVCP’s, remove spacers, double act cylinders
if valves are removed manually for single
acting cases).

Application Manual – Studies and Analyses 12/13/2023
• Unload all panel controlled capacity devices

(open FVCP’s, single act if SVU’s are provided)
• Consider and calculate the bypass line pres-
sure losses for a more accurate torque curve.
• Apply the final flywheel inertia from the
torsional analysis and current pulsation anal-
ysis for the final start up torque calculation
Bypass Line Pressure Losses:

• Ariel provides an entry for the bypass line
pressure loss. This is a value multiplied by the Torsional Vibration Analysis
number of stages, for a total pressure loss.
• The default value is 25 psi times the number Torsional Vibration Analysis is the analysis of the
of stages. This is only a rough value for a torsional dynamic behavior of a rotating shaft
beginning assumption. system as a result of forced vibration. Torsional
• The start up torque calculation will include a vibration, or twisting, is different from lateral
“flow at Start up”. Apply this value when vibration, or shaking. A torsional system,
calculating the bypass line pressure loss. At
compressor, driver, and coupling, are modeled
the lower ratios of start up (bypass line open)
as a mass-elastic system (inertia and stiffness) to
the flow can be much higher than the
compressor design flow. predict stresses in each component. Mass-elastic
properties of the system can be changed by
For electric motor drives, please also refer to adding a flywheel (additional inertia), using a soft
Electric Motor Drives topic. coupling (change in stiffness), or by viscous
damping (absorb natural frequency stimulation).
Not all systems require any modification to the
Typical Starting Torque Data and Curves mass-elastic properties to achieve a torsionally
provided within the Ariel Performance Software: sound system.
Ariel Corporation can provide the data for the

compressor necessary to perform a torsional
vibration analysis. This includes the torque effort
curves (torque versus crank angle), mass elastic
data and fourier coefficients representing the
torsional driving forces. The torsional analysis is
the responsibility of the Packager.
Care must be taken to represent the operating

conditionsthe unit will see, including any partial
load conditions. Any single acting cylinder
operation is important to include as these cases
can represent the more dynamic torque effort
curves.

When applying variations in speed and single When applying an electric motor driver, whether
acting cylinder configurations the torsional and fixed speed or variable speed, specific attention
acoustical response analysis will be much must be made to the motor shaft design. The
simplified by applying single acting configuration motor stub shaft and the section through the
only at one given speed. In order to eliminate drive end bearing should equal or exceed the
over complicating the torsional and acoustical compressor drive stub diameter. JGE:K:T/6 and
systems, specific capacity control methods may KBB:V frames have flanged drive end
be more attractive than others. For a discussion connections on the crankshaft, use the
on these methods, and recommendations on crankshaft journal diameter for the minimum
capacity control methods, refer to the Capacity motor shaft diameter.
and Load Control topic.
ER-83 provides torsional analysis limitations and
Capacity control sequencing can be very guidelines. Ariel provides Vibratory Torque
important when considering single acting Limits rather than allowable stress limits.
operating cases. Sequencing of cylinders for Appropriate safety factor and fatigue method has
unloading can be very important to both the been applied within these vibratory torque
torsional analysis as well as the acoustical limits. Auxiliary end limits and guidelines are
analysis. Single acting provides a much more defined. Flywheel overhung weight limits are
aggressive forcing function for the torsional defined along with the proper calculation
analysis. There is no absolute rule on which method.
cylinders to single act at a time, but a
The torsional analysis should be scheduled as
recommendation is to unload adjacent
early in the process as practical. Changes to the
cylinders before unloading opposing cylinders
system design may be required to satisfy the
(unloading opposing cylinders is much more
torsional analysis. This may include a different
aggressive on the torsional forcing function than
coupling type or model, the addition of a
unloading adjacent cylinders). The opposite is
flywheel, or on rare occasion a change to the
true for acoustical analyses when considering
compressor or driver design.
single stage compressors with symmetrical
pulsation vessels. These are recommendations
for a more polite torsional solution, but not the
Below is a list of data necessary for the different
only sequence that will work. A more aggressive
phases of a project:
load sequence, may just end up with a more
aggressive solution to the torsional (black out Quotation:
speeds, torsionally soft coupling, larger • System definition (compressor type / size,
flywheel...). driver type / size)
• If electric motor, define if fixed speed or vari-
Once a load sequence is chosen, this needs to be
able speed
applied to the torsional analysis, acoustical
• Include 4 to 7 operating points for review to
analysis, and the control panel logic sequence. If characterize the full operational map (condi-
the unloading is to be by manual methods, such tions and load steps) of the compressor
as removing valves, it is recommended to review
Purchase:
load sequences for any possible variation single
acting location.

• Full system layout defining compressor, • Fourier Coefficients

driver, coupling, speed control
Confirmation:
Compressor Load Data:
Confirm Torsional recommendations against
• Define the full range of operating conditions equipment on order or shipped. This includes
• Suction pressure range confirmation of:
• Discharge pressure range
• Flywheel size
• Load step sequence, including pockets and
single acting • Coupling model
• Speed range • Internal flywheel size
• Be sure to define load steps consistently • Detuner quantity and location
throughout the case manager • Driver dampener
• Be sure to provide the same load step Confirm Torsional solution through field
sequence for the acoustical analysis and (if verification at start up for larger, more
pneumatic capacity control devices) control
complicated and new driver compressor
panel logic
combinations, including
Compressor Data necessary for Torsional:
• Large Electric Motor Drives
• Performance run file for the compressor • Variable Frequency Drives
defining the full operating map • New Combinations of Driver / Compressor
• Mass elastic data • Complex Torsional Designs (black out
• Torsional supporting documents speeds, torsionally soft couplings, black out
• Performance report for each peak condition load steps)
• Gas analysis for each peak condition
Documentation:
• Crank effort curve for each peak condition
• Fourier coefficients for each peak condition • Recommend including the Torsional Study
report in the unit records book for the end
To Generate Data: user and jobsite
• Define the full operational map for the
compressor in the Case Manager
• Define the Summary Field Configuration to
include Peak-to-Peak/2 and Vector Sum 1
through 9 from the torsional section
• Run the Performance Summary and select
the cases with the highest Peak-to-Peak/2
and Vector Sum 1 through 9
Run the Report Manager selecting the
following reports:
• Configuration
• Mass Elastic Data
• Torsional Supporting Docs
• Performance
• Gas analysis
• Torque Demand Graph

Cylinder Numbering and

Phasing
* Standard Rotation for the JGI frame is counter-

clockwise

Ariel Application Manual

Uploaded by

Copyright:

Available Formats

Ariel Application Manual

Uploaded by

Document Information

Original Title

Copyright

Available Formats

Share this document

Share or Embed Document

Sharing Options

Did you find this document useful?

Is this content inappropriate?

Copyright:

Available Formats

Ariel Application Manual

Uploaded by

Copyright:

Available Formats

Application Manual 12/13/2023

ARIEL CORPORATION | www.arielcorp.com 1

Adjusted Equivalent Valve Area . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 23

ARIEL CORPORATION | www.arielcorp.com 2

Adjusted Equivalent Valve Area. . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 39

ARIEL CORPORATION | www.arielcorp.com 3

Cylinder, Lube Oil Distribution Block System. . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 58

ARIEL CORPORATION | www.arielcorp.com 4

Performance Application Limits . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 90

ARIEL CORPORATION | www.arielcorp.com 5

Purge and Vent Arrangements . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 112

ARIEL CORPORATION | www.arielcorp.com 6

ARIEL CORPORATION | www.arielcorp.com 7

ARIEL CORPORATION | www.arielcorp.com 8

ARIEL CORPORATION | www.arielcorp.com 9

ARIEL CORPORATION | www.arielcorp.com 10

Vision Statement products that can be manufactured, installed,

ARIEL CORPORATION | www.arielcorp.com 11

Phone Fax Email

Main Switchboard (740) 397-0311 (740) 397-3856

Order Entry (740) 397-3602

Ariel Response Center (740) 397-1060 arc@arielcorp.com

Ariel Field Service (740) 397-0311 (740) 397-3856

Ariel Corporation These numbers are in addition to the general

ARIEL CORPORATION | www.arielcorp.com 12

Ariel Response Center

ARIEL CORPORATION | www.arielcorp.com 13

ARIEL CORPORATION | www.arielcorp.com 14

Customer Technical Bulletins

ARIEL CORPORATION | www.arielcorp.com 15

Frame Class Equipment

JGM:JGP Frames For cylinder information refer to M, P, SP, JG

ARIEL CORPORATION | www.arielcorp.com 16

ARIEL CORPORATION | www.arielcorp.com 17

• Forged steel crankshaft • Non-metallic piston/rider rings (Piston Rings,

ARIEL CORPORATION | www.arielcorp.com 18

• Special wrenches and tools • Special wrenches and tools

ARIEL CORPORATION | www.arielcorp.com 19

ARIEL CORPORATION | www.arielcorp.com 20

• Main bearing temperature devices • Heavy-duty, horizontal balanced/opposed,

ARIEL CORPORATION | www.arielcorp.com 21

JGI Standard Equipment Primary Secondary

Ariel, vertical single throw air or gas compressor Horizontal 260 0

ARIEL CORPORATION | www.arielcorp.com 22

Definitions and Terms

Adjusted equivalent valve area is a measure of

JGM, JGP, JGN, JG, JGQ, 1.0

ARIEL CORPORATION | www.arielcorp.com 23

The main difficulty with higher compression

High Clearance Valve Assembly

Variable Volume Clearance Pocket

ARIEL CORPORATION | www.arielcorp.com 24

When compression ratios are in the higher range,

Cylinder Action, Double Acting

ARIEL CORPORATION | www.arielcorp.com 25

In order to maintain proper rod load reversal, the

ARIEL CORPORATION | www.arielcorp.com 26

Tandem cylinders are used to allow two stages of

Single acting cylinder operating cases should be