Lz4 V4uv0r en
Lz4 V4uv0r en
Lz4 V4uv0r en
com
L Z4 -V4UV0 R
DATASHEET
LZ4-V4UV0R
Datasheet
Published by ams-OSRAM AG
Tobelbader Strasse 30, 8141 Premstaetten, Austria
LZ4-V4UV0R
LZ4 Emitter on 4-Channel Star MCPCB
For emitter specification, please refer to the emitter datasheet
LZ4-00UV0R.
Features
- Thermal Resistance: 0.1 K/W (only MCPCB without emitter)
- Diameter of MCPCB: 19.9 mm
Ordering Information
Type
Total radiant flux 1)
IF = 700 mA
ΦE
Ordering Code
Note that binning is only performed on emitter level, and the binning of the emitter on MCPCB products follows the emitter
binning.
Dimensional Drawing 2)
Further Information:
Approximate Weight: 3,412.2 mg
Application Guidelines
Please note that the following diagrams use one of our MCPCB product as a general depiction of
the mounting structure. Refer to “Dimensional Drawing” section in this datasheet for the exact form
factor of the product in this datasheet.
Plastic washers
When optimizing the thermal performance, attention must also be paid to the amount of stress that is
applied on the MCPCB. Too much stress can cause the ceramic emitter to crack. To prevent this, it is
advisable to use plastic washers between the screw head and the MCPCB and to follow the torque range
listed on the next page.
─ For applications where heat sink temperature is 75 - 100 °C, it is recommended to use high
temperature and rigid plastic washers, such as polycarbonate washers.
─
For applications where heat sink temperature is less than 75 °C, nylon washers are acceptable.
The mounting of MCPCB assembly is a critical process step. Excessive mechanical stress build up
in the MCPCB can cause the MCPCB to warp which can lead to emitter substrate cracking and
subsequent cracking of the LED dies.
The following steps are recommended to avoid mechanical stress build up in the MCPCB:
─ Inspect bottom surface of MCPCB and top surface of heat sink for flatness and smoothness.
General flatness spec is 0.10 mm per 25 mm (0.004” per in) or better.
─ Always use M3 or #4-40 machine screws with M3 or #4 plastic washers. Use screws with flat
bottom such as pan head, socket head and rounded head. Do not use screws with conical
bottom, such as flat head screws.
─ For Star MCPCBs, only 3 sets of screws evenly spaced around the board are required and only
3 sets should be used (do not use more than 3 screws). For 50 mm boards (LZ7-Axxxxx,
LZP-Wxxxxx), use 3 screws in LED Engin standard screw holes or 2 screws in Zhaga
compatible screw holes (please refer to the mechanical drawing of respective product for exact
location).
─ Always use plastic washers in combinations with the screws. This avoids high point contact
stress on the screw head to MCPCB interface, in case the screw is not seated perpendicular.
─ When fastening the screws, it is recommended to tighten the screws in multiple small steps. This
method minimizes the chance of introducing unwanted MCPCB bending or tilting during
mounting process. The recommended torque range is 0.14 – 0.18 Nm (20 – 25 oz·in) for
LZP-Dxxxxx and LZP-Wxxxxx; 0.21 – 0.25 Nm (30 – 35 oz·in) for all other LED Engin MCPCB
products.
Wire Soldering
─ To ease the process of soldering wire to MCPCB, it is advised to preheat the MCPCB on a hot
plate of 125-150 °C. Subsequently, apply the solder and additional heat from the solder iron will
initiate a good solder reflow. It is recommended to use a soldering iron of more than 60 W.
─ It is advised to use lead-free, no-clean solder. For example: SN-96.5 AG-3.0 CU 0.5 #58/275
from Kester (pn: 24-7068-7601)
Tray 2)
Barcode-Product-Label (BPL)
2
3
2
#
"#$ %#&'()
'() 2
1
"$ #&'()
"$*+#&'
"(.$./
",$, -(((( !
0 ))
Width
Box
356 ± 5 mm
DATASHEET
L Z4 -V4UV0 R
Length
2)
206 ±5 mm
Barcode label
O
S S
em R
ic AM
(6 on
P)
BA du O
TC ct pto
H or
(1 NO s
T)
:
LO
T
NO
2100
: 12
(X
) 3G
2199
PR
8
OD H
12
NO 34
:
(9
D)
110 0
D/ M
C: ul LS
14 2
01
5
ti Y
44 TO
T6
(Q P 76
)Q LE
TY
:
D Bi Bin1
20 Bi n2 : P-
00 n3 : Q- 1-
ML : 1- 20
2 20
Te
Muster 3
2a
Ad 26 0 C R
22 mp
24 0 ST
R0 dit 0 C
ion C R
PA 77 al RT
Height (G
)
GR
CK
VA
R:
TE
XT
R
OU 18 DE
P: MY
P
-1
+Q
-1
54 ±5 mm
OHA02886
Original packing label
L Z4 -V4UV0 R
DATASHEET
Notes
The evaluation of eye safety occurs according to the standard IEC 62471:2006 (photo biological safety of
lamps and lamp systems). Within the risk grouping system of this IEC standard, the device specified in this
data sheet fall into the class high risk (exposure time less then 0.25 s). Under real circumstances (for ex-
posure time, conditions of the eye pupils, observation distance), it is assumed that no endangerment to the
eye exists from these devices. As a matter of principle, however, it should be mentioned that intense light
sources have a high secondary exposure potential due to their blinding effect. When looking at bright light
sources (e.g. headlights), temporary reduction in visual acuity and afterimages can occur, leading to irrita-
tion, annoyance, visual impairment, and even accidents, depending on the situation.
Subcomponents of this device contain, in addition to other substances, metal filled materials including silver.
Metal filled materials can be affected by environments that contain traces of aggressive substances. There-
fore, we recommend that customers minimize device exposure to aggressive substances during storage,
production, and use. Devices that showed visible discoloration when tested using the described tests above
did show no performance deviations within failure limits during the stated test duration. Respective failure
limits are described in the IEC60810.
Changes to the content of this datasheet may occur without further notification. JEDEC 46C constitutes the
guideline of the change management for the device specified in this document.
For further application related information please visit www.osram-os.com/appnotes
Disclaimer
Attention please!
The information describes the type of component and shall not be considered as assured characteristics.
Terms of delivery and rights to change design reserved. Due to technical requirements components may
contain dangerous substances.
For information on the types in question please contact our Sales Organization.
If printed or downloaded, please find the latest version on our website.
Packing
Please use the recycling operators known to you. We can also help you – get in touch with your nearest
sales office. By agreement we will take packing material back, if it is sorted. You must bear the costs of
transport. For packing material that is returned to us unsorted or which we are not obliged to accept, we
shall have to invoice you for any costs incurred.
In case buyer – or customer supplied by buyer – considers using our components in product safety devices/
applications or medical devices/applications, buyer and/or customer has to inform our local sales partner
immediately and we and buyer and /or customer will analyze and coordinate the customer-specific request
between us and buyer and/or customer.
Glossary
1)
Brightness: Brightness groups are tested at a current pulse duration of 10 ms and a tolerance of
±10 %.
2)
Tolerance of Measure: Unless otherwise noted in drawing, tolerances are specified with ±0.1 and
dimensions are specified in mm.
Revision History
Version Date Change
Published by ams-OSRAM AG
Tobelbader Strasse 30, 8141 Premstaetten, Austria
Phone +43 3136 500-0
ams-osram.com
© All rights reserved
14 | Version 1.1 | 2022-05-19