Maestro-600 Installation Manual

0$(6752 0$(6752
6 and 10 Zone Alarm Control Panel Installation Instructions
MAESTRO-600 / MAESTRO-1000 CONTROL PANEL
DE5281 1
Table Of Contents
1. INTRODUCTION ................................................ 3 8. EVENT REPORTING ....................................... 13
1.1 About This Manual ........................................................3 8.1 Reporting Options .......................................................13
1.2 Features .......................................................................3 8.2 Central Station Telephone No. 1 ..................................15
2. SPECIFICATIONS.............................................. 3 8.3 Central Station Telephone NO. 2..................................15
3. INSTALLATION ................................................. 3 8.4 System Account Codes ...............................................16
8.5 Communicator Formats ...............................................16
3.1 Location & Mounting......................................................3
8.6 Reporting Event Codes................................................16
3.2 Earth Ground ................................................................3
8.7 Auto Test Report.........................................................17
3.3 Power ...........................................................................4
8.8 Manual Test Report.....................................................17
3.4 Telephone Line Connection............................................4
8.9 Power Failure Report Delay .........................................17
3.5 Bell (Siren) Output ........................................................4
8.10 Recent Close Delay...................................................18
3.6 Programmable Output (PGM).......................................4
8.12 Report Code Disarming Options ................................18
3.7 Keypad & Keyswitch Connections..................................4
3.8 Keypad Zone Connections.............................................5 9. ARM/DISARM & ALARM OPTIONS ................ 18
3.9 Single Zone Input Connections ......................................5 9.1 “Timed” Auto Arming ..................................................18
3.10 Advanced Technology Zone (ATZ) Connections...........6 9.2 “No Movement” Auto Arming .......................................19
3.11 Fire Circuit ..................................................................7 9.3 “One-Key” Regular Arming ..........................................19
4. ACCESS CODES ............................................... 7 9.4 “One-Key” Home / ”System A” Arming.........................19
9.5 Arming Using Keyswitch or Pushbutton .......................19
4.1 Installer Code................................................................7
9.6 Bell Squawk ................................................................19
4.2 Master & User Codes....................................................7
9.7 Exit Delay....................................................................19
4.3 User / Access Code Length...........................................7
9.8 Beep on Exit Delay ......................................................19
4.4 Duress..........................................................................8
9.9 Alarm Transmission Delay...........................................19
4.5 Installer Lock.................................................................8
9.10 Silent Zones & Silent Panics Option ...........................19
5. PROGRAMMING METHODS ............................. 8 9.11 Bell Cut-Off Time.......................................................19
5.1 Hexa Programming .......................................................8 9.12 Code Priority .............................................................19
5.2 Hexa Streamlined Programming ....................................8
5.3 Decimal Programming...................................................9
10. PGM (PROGRAMMABLE OUTPUTS)...................... 20
10.1 PGM Types...............................................................20
5.4 Feature Select Programming .........................................9
10.2 PGM Timer Setting....................................................20
5.5 Key Access Programming .............................................9
10.3 PGM Options ............................................................21
6. PANEL SETTINGS FOR VISLOAD.................... 9
6.1 Panel Answer Options...................................................9
11. OTHER OPTIONS.......................................... 21
11.1 Telephone Line Monitoring (TLM)...............................21
6.2 Panel Identifier ............................................................ 10
11.2 Dialing Options..........................................................21
6.3 PC Password.............................................................. 10
11.3 Dialing Pulse Rates ...................................................21
6.4 Computer Telephone Number...................................... 10
11.4 Keypad Panic Options ...............................................21
6.5 Call Visload ................................................................. 10
11.5 Panel Time................................................................21
6.6 Answer Visload ........................................................... 10
11.6 Time Correction.........................................................21
6.7 Cancel Communication................................................ 10
11.7 Tamper/Wire Fault Recognition Options.....................21
6.8 Call Back .................................................................... 10
11.8 Tamper Bypass Options ............................................22
6.9 Automatic Event Buffer Transmission .......................... 10
11.9 Installer Test Mode....................................................22
7. ZONE DEFINITIONS ........................................ 10 11.10 Exclude Power Failure From Trouble Display............22
7.1 Zone Speed ................................................................ 10 11.11 Audible Trouble Warning .........................................22
7.2 Advanced Technology Zoning (ATZ) ............................ 11 11.12 Power Down Reset..................................................22
7.3 Intellizones .................................................................. 11
7.4 Silent Zones................................................................ 11
12. USER/KEYPAD FUNCTIONS ........................ 22
12.1 Programming Master & User Codes ..........................22
7.5 “24 Hour” & Fire Zones................................................ 11
12.2 Regular Arming .........................................................22
7.6 Instant Zones .............................................................. 11
12.3 Away Arming.............................................................23
7.7 Follow Zones............................................................... 11
12.4 Home Arming ............................................................23
7.8 Entry Delay 1 .............................................................. 11
12.5 Arming/Disarming Partitions ......................................23
7.9 Entry Delay 2 .............................................................. 11
12.6 System Disarming .....................................................23
7.10 Partitioning (Maestro-1000 only) ................................ 13
12.7 Alarm Memory...........................................................24
7.11 Bypass Enabled Zones.............................................. 13
12.8 Keyswitch or Pushbutton Arming / Disarming.............24
7.12 EOL Zones (Enabled/Disabled).................................. 13
12.9 Manual Zone Bypassing ............................................24
7.13 Keypad Zone 1 Supervision ....................................... 13
12.10 Bypass Recall .........................................................24
7.14 Keypad Zone 2 Supervision ....................................... 13
12.11 Keypad Chime Zones ..............................................24
12.12 Trouble Display Monitoring.......................................24
2 DE5281
,1752'8&7,21
Thank you for placing your trust in the MAESTRO-1000 and ATZ simplifies the task of meeting the zone requirements of any
MAESTRO-600 control panels. You have chosen a sophisticated, installation while reducing installation costs.
user-friendly control panel designed to meet all of your
technological, performance and security requirements. $ERXW 7KLV 0DQXDO
The superior capabilities of the MAESTRO-1000 and MAESTRO-600 This manual will provide you with all the information you will need to
control panels are driven by leading edge hardware and software. understand panel operation, features and functions. Even if you are
Use of the most powerful RISC processors on the market, with familiar with other security control panels, we recommend that you
built-in “analog-to-digital” converters and SMD technology, means read this entire manual at least once to familiarize yourself with
our control panel requires 30-40% less components than any panel features and programming. For your convenience a
previous generation. “Programming Guide” is included in order to keep track of which
The reduced number of steps required to program these control addresses were programmed and how.
panels increases the speed of installation and end-users can
access most system features at the touch of just one key. A )HDWXUHV
“streamlined programming” feature further simplifies the MAESTRO-1000: 10 zones (4 onboard inputs w/ATZ = 8 zones + 2
programming process, by saving data automatically and leading the keypad zones)
installer through the programming addresses without the need to MAESTRO-600: 6 zones (4 onboard inputs + 2 keypad zones)
enter them manually. Common features
Important advances have been made in MAESTRO control panel • Powerful 16-bit RISC processor with built-in analog to digital
technology, which guarantee exceptional levels of false alarm converters.
protection. A full range of high-tech features dramatically reduces
• User-friendly programming
the frequency of false alarms. These easy to use tools include
“Intellizone” definition, “Auto Zone Shutdown”, “Beep On Exit Delay”, • “False Alarm Prevention” features such as: Intellizones, Auto
“Programmable Delay before Alarm Transmission” and “Recent Zone Shutdown, Beep on Exit Delay, Programmable Delay
Closing” report. Before Alarm Transmission, and Recent Closing Report.
Each control panel can be used to monitor two distinct security • 2 Flexible Partitions (MAESTRO-1000 only)
systems. Partitioning provides a practical and flexible solution in • High-Speed Pre-Programmed or Programmable Communication
situations where combined systems are a necessity. Zones can be Formats
assigned to “System A”, “System B”, both systems or given no • 256 Event Buffer with time and date stamp
system assignment. MAESTRO panels can reduce set-up and
• Fully Programmable Output (PGM)
reporting time by transmitting pre-programmed event codes and
using high-speed communicator formats. Almost any control panel • 48 User Codes, 1 Master Code, 1 Installer Code
condition or event may be used to activate the MAESTRO’S • Telephone Line Monitoring (TLM)
programmable output (PGM). Once a panel status mode is selected • 3 panic alarms, activated via the keypad
for the PGM to follow, the polarity and duration of the output may
• Regular Arming, “Home” Arming, “Double Home” Arming,
also be programmed.
“Away” Arming, “One-Key Regular Arming”, “One-Key Home
The MAESTRO-1000 control panel includes the Advanced Arm”, “One-Key” Exit & Re-arm, “Timed Auto Arming”, “No
Technology Zoning (ATZ) feature, which was developed to permit Movement Auto Arming”, Keyswitch or Pushbutton Arming
connection of 2 zones on one zone input terminal, as well as
providing wire fault recognition on both zones.
63(&,),&$7,216
Battery Charger: 360mA with dynamic Battery test. AC input: 16.5 VAC, 40VA, 50 - 60Hz
Aux. Power: 400mA, Fuseless electronic shutdown at 1A, PGM output: N.C. or N.O to ground, 50mA Max.
Automatic restore Serial Data Output: (1200, 1, N) for use with accessory modules
Bell Out: 1A, Fuseless electronic shutdown at 3A, Automatic (not UL systems).
restore
,167$//$7,21
/RFDWLRQ 0RXQWLQJ
Before mounting the cabinet, push the five white nylon-mounting
studs into the back of the cabinet. The circuit board should not be
mounted into the back of the cabinet, until all cables are pulled into
the cabinet and prepared for connection. Select an installation site
that is not easily accessible to intruders. Leave at least 2” around
the panel box to permit adequate ventilation and heat dissipation.
The installation site should be dry and close to an AC source,
ground connection and telephone line connection.
(DUWK *URXQG

Connect the zone and dialer ground terminals from the control panel
to the cabinet and cold water pipe or grounding rod as per local
electrical codes.
DE5281 3
3RZHU 7HOHSKRQH /LQH &RQQHFWLRQ
Connect the incoming telephone company wires into the tip and ring
3.3.1 AC Power connections of the control panel. Then run the wires from t1 and r1
NOTE: Initial setup and to the telephone system as shown in figure 4.
power-on must be performed
while AC power is connected.
The system will not operate $&
$&
with backup battery only, during 32:(5
initialization.
Use a 16.5VAC (50-60Hz) 7UDQVIRUPHU
transformer with a minimum 9$& 9$
40VA rating to provide sufficient

AC power.
Do not use any switch-controlled outlets to power the transformer.
Connect the transformer as shown in fig. 2. After applying power to
the control panel, it will perform a hardware verification. Once this is
completed, the auxiliary power terminals will be enabled in order to
power all accessories connected to its terminals, such as keypads
%HOO 6LUHQ 2XWSXW
The BELL+ and BELL- terminals,
and motion detectors. The control panel will then perform a battery
power bells and/or other warning
test and re-instate the last system status (i.e. alarm, system armed,
devices requiring a steady voltage
etc.). The control panel will then begin displaying the current system
output during an alarm. The bell
status (i.e. open/closed zones, troubles, etc.)
output supplies 12VDC upon alarm
Caution: Do not connect the transformer or the back-up battery and can support two 20-watt or two
until all wiring is completed! 30-watt bells output.
3.3.2 Back-up Battery
In case of power loss, connect a Caution: The bell output is microprocessor-controlled and will
back-up battery. Use a 12VDC automatically shut down if the current exceeds 3A.
7Ah rechargeable acid/lead or gel If the load on the bell terminals returns to normal (≤3A), the control
cell battery. Connect the back-up panel will re-instate power to the bell terminals upon generation of
battery after applying the AC another alarm. When connecting sirens (speakers with built-in siren
power. When installing verify drivers) please verify correct polarity. Connect the positive lead to
proper polarity, as reversed the BELL+ terminal and the negative lead to the BELL- terminal of
connections will blow the battery the control panel as shown in figure 5.
fuse. Connect the "RED" battery
lead to the positive battery
terminal, and the "BLACK"
3URJUDPPDEOH 2XWSXW 3*0
The Maestro Control Panel includes a programmable output. When
battery lead to the negative a specific event or condition occurs in the system, the PGM can be
battery terminal of the control used to reset smoke detectors, activate strobe lights, open/close
panel as shown in fig. 3. garage doors and much more. The PGM provides a 50mA output.
If the current draw on the PGM output is to exceed 50mA, we
3.3.3 Auxiliary Power Terminals recommend the use of a relay as show in figure 6. Each PGM is
The AUX+ and AUX- terminals on the control panel can provide a
programmable to toggle on and off from more than a thousand
maximum of 400mA 12VDC. Use the auxiliary power supply to
different events. For example, PGM can open and close an
power the motion detectors, keypads and other accessories in your
automatic garage door by pressing keys [1] and [2] simultaneously
security system. Although, their combined current consumption
on keypad. For details on how to program the PGM, refer to section
should not exceed 400mA. The auxiliary supply is
10 PGM (Programmable Outputs).
microprocessor-protected against current overload and
automatically shuts down if the current exceeds 1A. Auxiliary power
will resume once the overload condition has restored and within
1-60 seconds after performing the battery test.
3.3.4 Battery Test
The Control Panel conducts a dynamic battery test under load every
60 seconds. If the battery is disconnected, or its capacity is too low,
the trouble indicator will illuminate on the keypad (red “1” indicator).
The red “1” indicator also comes “on” if the battery voltage drops to
10.5 volts or less while the control panel is running on the back-up 5HOD\ IRUP &
battery (no AC). At 8.5 volts, the panel shuts down and there is no
outputs.
3.3.5 Keypad Function Test
We recommend conducting a "power-up" test on keypads installed
far from the control panel. To do so temporarily connect the
.H\SDG .H\VZLWFK &RQQHFWLRQV

keypads close to the control panel and connect the transformer.
After 10 seconds, begin entering random commands on the keypad
and verify that the keypad "beeps" in response to these commands.
Connect the four keypad connections labeled red, black, green and
Then open a zone to ensure that the keypad and the control panel
yellow to the corresponding color terminals on the control panel as
are responding to these signals. If the keypad does not respond and
indicated in figure 7. Connect the keyswitch, in series with 220 ohm
indicator lights do not illuminate, verify that approximately 16VAC is
resistor, to the GRN/BLK terminals of the control panel as shown in
present at the “AC” terminals. If AC is present, check the keypad
figure 7. Refer to sections Arming Using Keyswitch and keyswitch
wiring and verify there isn’t a short between the "black" and "red”
or Pushbutton Arming (section 12.8) for more information on
keypad wires. If the keypad does not respond, please contact your
keyswitches.
local distributor.
4 DE5281

RKP
.H\SDG =RQH &RQQHFWLRQV

Each keypad comes with one zone input terminal, allowing you to
connect one detector or door contact directly to the keypad.
Example: A door contact located at the entry point of an
establishment can be wired directly to the zone input terminal of
Figure 10 describes the keypad tamper switch connections.
the entry point keypad instead of wiring the door contact all the
way to the control panel. NOTE: The standard KP-601 does not include a tamper switch. In case
your version includes a tamper switch, see figure 10 for wiring
The keypad will communicate the status of the zone to the control
instructions.
panel as though the input was on the control panel. Therefore,
adding one or two zones to your security system. Regardless of the
number of keypads in the system, the control panel supports a
maximum of two keypad zones.
Example: A security installation is comprised of four keypads. Of
these four keypads only two can have their zone input terminals
enabled (see figure 9). The other two keypads must have their
zone input terminals disabled as described below.
Keypad’s whose zone input terminals are not being used, must be
disabled. To disable the Maestro-601 keypad zone, connect a 1KΩ
resistor short between the ZONE and BLK terminals of the keypad.
On the other hand, if you are using the keypad zones, you must
define them as either Keypad Zone 1 or Keypad Zone 2 as
described below.
Note: if using two keypad zones, one keypad must be defined as
keypad zone 1 while the other must be defined as keypad zone 2.
The control panel will recognize these added zones as shown in
table 1.
Once the keypad zones have been defined, you must enable
Table 1 – Keypad Zone Recognition
“Keypad Zone Supervision” in the control panel (see section 7.13
and 7.14.). Figures 8 and 9 demonstrate typical keypad zone input Zone Select Jumper “OFF” = Keypad Zone 1
Zone Select Jumper “ON” = Keypad Zone 2
installations. Note that keypad zones always use a 1KΩ EOL
resistor. Note: If the zone select jumper is changed, the control panel will only
recognize the change when the keypad is disconnected and re-connected.
MAESTRO-1000 MAESTRO-600
(ATZ Disabled) (ATZ Enabled)
Kpd Zone 1 = Zone “5” Kpd Zone 1 = Zone “9” Kpd Zone 1 = Zone “5”
Kpd Zone 2 = Zone “6” Kpd Zone 2 = Zone “10” Kpd Zone 2 = Zone “6
6LQJOH =RQH ,QSXW &RQQHFWLRQV

The system hardware recognizes the following single zone input
terminal connections. For more information on programming the
options mentioned below refer to ZONE DEFINITIONS, section 7.
DE5281 5
3.9.1 N.C. Contacts, Without EOL Resistor
If your security installation does not require tamper or wire fault
detection, connect the detection devices and program the control
panel as shown in figure 11. This setup will communicate an open
or closed zone to the control panel, illuminating the corresponding
indicator on the keypad when the zone is open. Do not use devices
with normally open contacts in this setup, as this will cause the
control panel to remain in alarm.
3.9.2 N.O. and N.C. Contacts, With EOL Resistor
$GYDQFHG 7HFKQRORJ\ =RQH $7=

recognition but requires the use of normally open and normally
closed contacts, connect all detection devices with a 1KΩ end of
line (EOL) resistor and program the control panel as shown in
figures 12 and 13. This setup will communicate an open or closed &RQQHFWLRQV
zone to the control panel, illuminating the corresponding indicator on Enabling the ATZ feature (see section 7.2) allows you to install two
the keypad when the zone is open. detection devices per input terminal, therefore, doubling zone
capacity of the control panel. Advanced Technology Zoning is a
software-oriented feature, there is no need for extra modules, simply
install the devices as shown in figures 17 to 19. The control panel
will recognize and display the status of the installed devices as
shown in figure 16. The extra zones, function exactly like any other
zone, displaying zone status on the keypad and sending separate
alarm codes for each zone. For more information on programming
the options mentioned in the following sections refer to Zone
Definitions section.
NOTE: This feature is not available on the MAESTRO-600 Control
Panel!
3.9.3 N.C. Contacts, Without EOL Resistor, With

Tamper Recognition
If your security installation requires tamper recognition, all detection
devices must use normally closed contacts. Connect the devices
and program the control panel as shown in figure 14. This setup will
communicate an open or closed zone to the control panel,
illuminating the corresponding indicator on the keypad when the
zone is open. The control panel will also communicate any detected
tampers (cuts) as Tamper/Wire Fault Recognition Options (see 3.10.1 ATZ N.C. Contacts, Without EOL Resistor
section 11.7).
recognition but requires the use of two zones per input, connect the
detection devices and program the control panel as shown in figure
17. Do not use devices with normally open contacts, as this will
cause the system to remain in alarm. This setup will communicate
the status of each device to the control panel (see figure 16), where
an open zone will illuminate the corresponding LED indicator on the
keypad.
3.9.4 N.C. Contacts, With EOL Resistor, With

Tamper and Wire Fault Recognition
If your security installation requires tamper (cut) and wire fault
(short) recognition, all detection devices must use normally closed
contacts. Connect the devices and program the control panel as
shown in figure 15. This setup will communicate an open or closed
zone to the control panel, illuminating the corresponding key on the
keypad when the zone is open. The control panel will also
communicate any detected tampers (cuts) and/or wire faults (short)
as per Tamper/Wire Fault Recognition Options (see section 11.7).
3.10.2 ATZ N.C. Contacts, Without EOL Resistor,
With Tamper Recognition
If your security installation requires tamper recognition and two
zones per input terminal, connect the detection devices and
6 DE5281
program the control panel as shown in figure 18. Do not use devices alarm. If the line is "open", the control panel will send a "fire loop"
with normally open contacts, as this will cause the zone to remain trouble report to the central station and illuminate the “TRBL”
open. This setup will communicate the status of each zone to the indicator on the keypad.
control panel (see figure 16), where an open zone will illuminate the
corresponding LED indicator on the keypad. The control panel will
also communicate any detected tampers (cuts) on the system as
per Tamper/Wire Fault Recognition Options (see section 11.7).
3.11.2 Supervised 4-Wire, Latched, Smoke Detector

Installation
To reset (unlatch) the smoke
3.10.3 ATZ N.C. Contacts, With EOL Resistor, With detectors after an alarm,
momentarily interrupt power to
Tamper & Wire Fault Recognition
the detectors. To do so, verify
If your system requires tamper (cut) and wire fault (short)
that the negative (-) of the smoke
recognition, connect the two detection devices to one input terminal
detectors are connected to the
with a 1KΩ end of line (EOL) resistor and program the control panel
PGM.
as shown in figure 19. Do not use devices with normally open
contacts, as this will cause the zone to remain open. This setup will To supervise the power supply,
communicate the status of each zone to the control panel (see install an “end of line” relay (relay
figure 16), where an open zone will illuminate the corresponding form “C”). Connect the smoke
LED indicator on the keypad. Any tampers (cuts) and/or wire faults detectors and relay as shown in
(shorts) detected on the system are communicated as per figure 21. In the event power is
Tamper/Wire Fault Recognition Options (see section 11.7). interrupted the relay will cause a
)LUH &LUFXLW

fire trouble report (see section
7.5, “24 Hour” & Fire Zones.)
If your security installation requires the use of smoke detectors, you
must define zone 3 as a “24-hour fire” zone; please refer to section
Set the PGM for “Timed N.C.” (normally closed), and program the
7.5.
PGM to “open” when any two keys on the keypad are pressed
3.11.1 Standard Installation simultaneously. For more information on programming the PGM
Connect the smoke detectors to zone 3 as shown in figure 20. Note refer to section 10 PGM (Programmable Outputs)
that a fire zone must use a 1KΩ EOL resistor. If there is a line short EXAMPLE:
or if the smoke detector becomes active, whether the system is To program the PGM to conduct a smoke detector reset when
armed or disarmed the control panel will generate an the [CLR] and [ENT] keys are pressed at the same time.
Address 039 = [BYPASS] [2ND]
Address 040 = [5] [0]
Address 042 = [2ND] [6]
Address 056 = [0] [0] [4]
$&&(66 &2'(6
,QVWDOOHU &RGH 0DVWHU 8VHU &RGHV
Î
Streamline (for description, see Programming Guide) - Section 00 Default Master Code: 0000
Hexa Programming - Addresses 000-002
Please note you can not use the Installer Code to program the
Default = 1111 Master and User codes. Only the Master and User 1 Codes can
Only the installer code provides you with access to program all program these codes. For details on Programming Master & User
settings in the control panel. Only the Master and User access Codes go to section 12.1.
8VHU $FFHVV &RGH /HQJWK

codes can not be programmed using the installer code. To program
any setting in the control panel you must enter the programming
mode by pressing the [ENT] key followed by the Installer Code. The
installer code contains six digits and each digit can be any value
Feature Select Programming Î Address 088, key [9].
Default: 4-digit Access Codes.
from 0 to 9. When programming the installer code, always enter six
digits. When entering an access code into the control panel, the control
panel can grant access after entering all six digits or after entering
[ENT] + [INSTALLER CODE] + [0] [0] [0] + First 2 digits + [0] [0] [1] +
the first four digits of the code.
Next 2 digits + [0] [0] [2] + Final 2 digits + [ENT]
DE5281 7
LED “9” off: 4-digit Access Codes LED “10” on: Duress Enabled
LED “9” on: 6-digit Access Codes [ENT] + [installer code] + [0] [9] [0] + “10” On/Off + [ENT] + [ENT]
[ENT] + [installer code] + [0] [8] [8] + “9” On/Off + [ENT] + [ENT]
,QVWDOOHU /RFN
'XUHVV Decimal Programming Î Address 058
Feature Select Programming Î Address 090, key [0] Default: Address Empty
Default: Duress Disabled Program 147 into address 058 to enable the installer lock. Hence, a
When unwillingly forced to disarm a system, entering User Code hardware reset (see section Power Down Reset) will not affect the
#48 instead of the usual code, will disarm the system and send a current settings. To remove the installer lock, enter any value other
silent alert (Duress Code) to the Central Station. than 147.
LED “10” off: Duress Disabled [ENT] + [installer code] + [0] [5] [8] + [1] [4] [7] + [ENT]
352*5$00,1* 0(7+2'6
When programming, use the supplied “Programming Guide” to keep This makes for quicker programming.
track of which addresses were programmed and how. Before you Note, the keypad will not display the current data in the Hexa
begin programming the control panel, we recommend you read Streamlined Programming method. To program using the Hexa
sections 5 through 11 of this manual in order to acquire a good Streamlined Section method:
understanding of the control panel and its many features. When 1. Press [ENT] + [installer code] + [7].
programming with the keypad, certain addresses are programmed
2. The red “PRG” and “2nd” LED indicators will flash to indicate
using different methods. These methods are described in detail
you are in programming mode.
below. Each section in this manual will reference the appropriate
programming method. 3. Enter [2-digit section] (00-67)
+H[D 3URJUDPPLQJ 4. The red “PRG” indicator will remain on and “2nd” LED indicator will
turn off.
Addresses 000 to 043 and 300 to 527 are programmed using the 5. Enter [8-digit data] to program the section.
Hexa Programming method. In this mode, you can enter any
6. The keypad will sound a confirmation “beep” to indicate that the
hexa-digit from 0-F where keys [1] to [9] represent digits 1 to 9
section has been programmed, data is saved and that the
respectively; the other keys represent hexa digits A to F as shown
software has advanced to the next section.
in figure 22. To program using the Hexa Programming method:
7. Return to step 5 to continue programming at the next address or
1. Press [ENT] + [installer code]
press [CLR] to exit the programming mode.
2. The red “PRG” indicator will flash indicating you are in
programming mode
3. Enter the desired [3-digit address] and the red “PRG” indicator
will remain illuminated.
4. The keypad will display the 2-digit data currently saved at this
address as described in figure 23
5. Enter [2-digit data]; after entering data you do not need to press
[ENT], the software will automatically save the data into the
selected address.
6. Return to step 2 to continue programming or press [CLR] to exit
programming mode.
+H[D 6WUHDPOLQHG 3URJUDPPLQJ

This is an alternate method to Hexa Programming. The addresses
(000-043 and 300-527) programmed in the Hexa Programming
method are grouped into 67 sections where each section contains
four addresses (i.e. section 11 = addresses 300-303). Using this
method allows you to program 8 digits (4 addresses) without having
to exit and re-enter addresses. When entering the final digit, the
software will automatically advance to the next section.
Example: If you complete the “Programming Guide” with the
desired data, you can program the 67 sections by entering all 567
digits without pressing [ENT] or entering any other addresses.
8 DE5281
4. The keypad will now display the 3-digit data currently saved at
this address as described in figure 24
5. Enter [3-digit data] (000-255); after entering data you do not
need to press [ENT], the software will automatically save the
data into the selected address.
programming mode
)HDWXUH 6HOHFW 3URJUDPPLQJ

Addresses 062 to 126 are programmed using the Feature Select
Programming method. In this method, each key in every address
represents an option or feature. Pressing a key will illuminate the
corresponding LED indicator on the keypad and pressing the key
again will extinguish the indicator. The On/Off status of each light
determines the selected features. To program using the Feature
Select Programming method:
2. The red “PRG” indicator will flash to indicate you are in
programming mode
3. Enter [3-digit address] (062-126)
4. After entering the address, the keypad will display the feature
selection status. The On/Off status of the keypad LED indicators
determines the selected features as described in the
“Programming Guide” and in the appropriate sections of this
manual. Turn the LED indicators on/off by pressing the
corresponding key until the desired options are set. Then press
the [ENT] key to accept, there will be a confirmation “beep”
indicating the options have been accepted. The “PRG” indicator
will flash to indicate that the software is awaiting the next
'HFLPDO 3URJUDPPLQJ

address entry
Addresses 044 to 061 are programmed using the Decimal programming mode
Programming method. Values entered must contain three digits
from 000 to 255. .H\ $FFHVV 3URJUDPPLQJ
To program using the Decimal Programming method: This method allows for quick programming of features without
entering addresses or section numbers. The following features are
programmed using the installer code as well as the master and user
2. The red “PRG” indicator will flash to indicate you are in 1 codes.
programming mode • Auto Arm Time: for details see parag. 9.1.1
3. Enter [3-digit address] (044-061) and the “PRG” indicator will • Panel Time: for details see parag. 9.5
remain on • Manual Test Report: for details see parag. 8.8
3$1(/ 6(77,1*6 )25 9,6/2$'

3DQHO $QVZHU 2SWLRQV the panel will pick up the line on the first ring. If it takes more than
40 seconds, the panel will not answer on the first ring and the
Streamline - Section 00 Î Hexa Programming - Address 003 answering machine will answer after three rings.
[ENT] + [installer code] + [0] [0] [3] + 1st digit + 2nd digit (1-15
Default: Answering Machine Override Disabled & Maximum 8 rings.
The following two options will define how the control panels answer rings) + [ENT]
an incoming call from a computer using the Visload software. The second digit represents the number of rings the control panel
In order for the Visload software to remotely communicate with the will wait before picking-up the line. If the line is not answered after
control panel, call the installation site twice using the Visload the number of re-programmed rings, the control panel will answer
Software. To do so, program the first digit in address 003 with any the call. Note the control panel resets the "ring" counter every 64
value from 1-F (see table 2 at the end of this section), this value seconds. Therefore, if someone or an answering machine answers
represents the delay period the control panel will wait between the a call before the number of pre-programmed rings has elapsed, the
first and second call. Using the Visload software, call the installation control panel will keep the number of rings in memory for 64
site and on the second ring press [enter] on the keyboard to seconds. If you hang-up and call the installation site back within 64
hang-up. After hanging up, the Visload software will immediately call seconds, the control panel will continue to count the number of rings
the installation site back. If the installation site is called back within from the first call. After reaching the total number of rings, the
the programmed delay period, the control panel will override the control panel will answer the call. The number of rings can be set
answering machine or service by picking-up on the first ring. To from 1-15 by programming the second digit at address 003 with any
disable this option program [2nd] or [1] as the first digit in address hexa-digit from 1-F. Program the second digit with [2nd] to disable
003. this option.
Example: A security installation is using an answering machine set Example: Address 003 = [2nd] [8]. Using the Visload software, you
to answer after 3 rings, the first digit at address 003 has been call an installation site where there is no answering machine or
programmed with [5] (40 sec.) and the second digit has been service and no one is home. Since there is no one to answer the
programmed with 8. When you call the installation site with the telephone call, the control panel will pick-up the line on the eighth
Visload software the first time, wait two rings and press [enter] on ring. If someone happens to be home and answers the telephone,
the keyboard. The Visload software will immediately call the say, after three rings, the control panel will keep the three rings in
installation site back. If the second call is made within 40 seconds, memory for 64 seconds. If you hang-up and call back the installation
DE5281 9
site within 64 seconds the control panel will answer the call on the By entering the code sequence listed below, you can manually force
fifth ring. If you call back after 64 seconds the "ring" counter will the control panel to answer any incoming calls from the Visload
have been reset and the control panel will answer the call on the software. This option can also be used to perform an on-site
eighth ring. upload/download by connecting your computer directly to the control
NOTE: If you program four or less rings, the control panel will panel using an ADP-1 line adapter (ADP-1 is a module that can be used
always reset the counter! to connect a modem directly to the panel without the phone line) and
manually answering Visload from the control panel. In Visload go to:
Table 2 - Answering Machine Override Options
[2nd] or [1] = Answering Machine Override disabled
Main Menu Î Program Setup Î Setup Î
Modem & Printer
Configuration
[2] = 16 sec. [4] = 32 sec. [6] = 48 sec. [8] to [TRBL] = 60 sec. Set "Dialing Condition" to "Blind Dial". Program the panel telephone
[3] = 24 sec. [5] = 40 sec. [7] = 56 sec. number in Visload and follow the instructions on the ADP-1 adapter.
Note: for more details, refer to the Programming Guide - When the computer has dialed press:
Streamline section “00” and “014”. [ENT] + (Installer, Master, or User 1 Code) + [AWAY]
3DQHO ,GHQWLILHU &DQFHO &RPPXQLFDWLRQ

Streamline - Section 01 Î Hexa Programming - Addresses Key Access Programming Îkey [HOME]
004-005 Use the Installer Code to cancel all communication and erase any
This four-digit code identifies the control panel to the Visload unreported events in the buffer until the next reportable event. Use
software before initiating upload. Program the same 4-digit code into the Master or User 1 code to cancel communication attempts with
the control panel and the Visload software before attempting to Visload.
establish communication. If the codes do not match, the control [ENT] + (Installer, Master & User 1 Code) + [HOME]
&DOO %DFN

panel will not establish communication. Enter any hexa digits from 0
to F.
[ENT] + [installer code] + [0] [0] [4] + First 2 digits + [0] [0] [5] +
Final 2 digits + [ENT]
Feature Select Programming Î Address 086, key [4]
3& 3DVVZRUG

Default: Call Back Disabled
For additional security, when a PC using the Visload software
Streamline - Section 01 Î Hexa Programming - Addresses
attempts to communicate with the control panel, the control panel
can hang-up and call the PC back in order to re-verify identification
006-007
codes and re-establish communication. When the control panel
This four-digit download password identifies the PC to the panel, answers the call, it will verify if the Panel ID and PC Passwords
before beginning the download process. Enter the same password match and if they do, the control panel will hang-up and call the
into the Visload software and the control panel. If the passwords are Visload software back. The Visload software will automatically go
not the same, Visload will not establish communication. Enter any into "wait for dial tone", ready to answer when the control panel calls
hexa digits from 0 to F. back. Please note the Computer Telephone Number (see section
[ENT] + [INSTALLER CODE] + [0] [0] [6] + First 2 digits + [0] [0] [7] + 6.4) must be programmed in order to use the "Call Back" feature.
Final 2 digits + [ENT] LED “4” off: Call Back Disabled
&RPSXWHU 7HOHSKRQH 1XPEHU LED “4” on: Call Back Enabled
Î [ENT] + [INSTALLER CODE] + [0] [8] [6] + “4” On/Off + [ENT] + [ENT]
$XWRPDWLF (YHQW %XIIHU

Streamline Section 02 & 03 Hexa Programming - Address
008-015
The control panel will dial this telephone number when trying to
7UDQVPLVVLRQ
Î
initiate communication with the PC (see section 6.5 Call Visload).
There is no default telephone number and you can enter any Feature Select Programming Address 088, key [2nd]
number from 0-9 up to a maximum of 16 digits. If you would like to Default: Automatic Event Buffer Transmission Disabled
enter any special keys or functions refer to table 3 in section 8.3. If
When the event buffer reaches 50% capacity, the control panel will
the telephone number contains less than 16 digits, press the [TRBL]
make two attempts to establish communication with a PC. The
key to indicate the end of the telephone number.
control panel will call the Computer Telephone Number (see section
[ENT] + [INSTALLER CODE] + [7] + [0] [2] + Telephone Number (if 6.4) programmed at addresses 008 to 015. The Visload software
<16 digits press [TRBL]) + [ENT] must be in "wait for dial tone" mode. When the system establishes
&DOO 9LVORDG communication, it will upload the contents of the event buffer to the
Key Access Programming Î key [TRBL]

Visload software. If communication is interrupted before
transmission of the complete contents of the buffer, or if after two
The control panel will dial the telephone number entered at attempts, communication is not established, the system will wait
addresses 008-015 (see section 6.4) in order to communicate with until the event buffer is full before attempting to re-communicate
the Visload software. The control panel and the computer will verify with Visload. When Event Buffer is full, each subsequent new event
that the Panel Identifier and the PC Password match before will erase the oldest event in the buffer.
establishing communication (see sections 6.2 and 6.3). LED “2nd” off: Automatic Event Buffer Transmission Disabled
Press [ENT] + (Installer, Master, or User 1 Code) + [TRBL] LED “2nd” on: Automatic Event Buffer Transmission Enabled
$QVZHU 9LVORDG [ENT] + [INSTALLER CODE] + [0] [8] [8] + “2ND” On/Off + [ENT] + [ENT]
Key Access Programming Î Key [ AWAY]
=21( '(),1,7,216
Note: When defining zones characteristics, refer to “zone The zone speed applies to all zones whether the system is armed or
definition” table, in the programming guide. disarmed. The zone speed defines how quickly the control panel will
=RQH 6SHHG respond to an open zone. The control panel will not display and/or
Decimal Programming Î Address 053 respond to an open zone until the programmed zone speed elapses.
All other zone definitions and options do not come into effect until
Default: 600mS the zone speed has elapsed.
10 DE5281
Example: The system is armed and the zone speed is set for 1.2 • A trouble indicator, “HOME”, and a fire zone indicator, “3”, will
seconds. A zone opens and closes in less than 1.2 seconds, the flash on the keypad.
control panel will respond as though nothing happened (i.e. no • Alarms will generate an intermittent output signal as
reporting, no alarm and no display on keypad). demonstrated by the figure below, regardless of the system’s
The zone speed can be set from 15ms to 3.8s (001 to 255 X current arming status.
15ms). This feature prevents any momentary glitches in the system • Alarms are always audible, regardless of other settings.
from causing an alarm or unnecessary reporting. %(// 287387 '85,1* ),5( $/$50
[ENT] + [installer code] + [0] [5] [3] + 3 digit decimal value (001-255)
+ [ENT]
$GYDQFHG 7HFKQRORJ\ =RQLQJ
$7=
Default: ATZ Disabled
NOTE: This feature is not available on the Maestro-600 Control 7.5.1 Zone 4 (Enable/Disable)
Panel!
Enabling the ATZ feature allows you to install two detection devices
per zone input. Each detection device will have its own zone and Default: Zone 4 Enabled
each will transmit a separate alarm code that will display on the If the ATZ feature is enabled and zone 3 has been set as a fire
keypad. For information on how to connect the detection devices zone, zone 4 must be disabled if it is not going to be used.
and how the panel recognizes them, please refer to section LED “1“ off: Zone 4 Enabled
Advanced Technology Zone (ATZ) Connections . LED “1“ on: Zone 4 Disabled
LED “8” off: ATZ Disabled [ENT] + [installer code] + [0] [9] [0] + “1” On/Off + [ENT]
LED “8” on: ATZ Enabled
,QVWDQW =RQHV
[ENT] + [installer code] + [0] [9] [0] + “8” On/Off + [ENT]
,QWHOOL]RQHV Feature Select Programming Î Address 104, keys [1] to [0]
Feature Select Programming Î Address 092, keys [1] to [0]

Using the “Feature Select Programming Method”, identify or select
which zones will be defined as Instant Zones. If an “Instant” zone
If an alarm condition occurs on a zone identified as Intellizone, the opens, the control panel will immediately generate an alarm after the
control panel will not trigger an alarm until one of the following “Zone Speed” has elapsed.
conditions occurs within a specified period (see Intellizone Time
)ROORZ =RQHV
Î
Delay, section 7.3.1):
• An alarm condition occurs on another zone. Feature Select Programming Address 108, keys [1] to [0]
• The zone that is in alarm has restored and re-occurred. Using the “Feature Select Programming Method”, identify or select
• The zone that is in alarm remains in alarm the entire period. which zones will be defined as Follow Zones. Follow zones function
Note the Intellizone timer will only begin after the Zone Speed period as follows:
has elapsed (see section 7.1). • If a follow zone opens and no entry delay zones have been
CAUTION: Do not use the Intellizone feature on zones triggered, the control panel will generate an alarm immediately
programmed with any Entry Delay! An alarm may occur when after the zone speed has elapsed.
disarming the system. • If a follow zone opens during another zone's entry delay period,
the control panel will wait until the end of the entry delay period
7.3.1 Intellizone Time Delay
Decimal Programming Î Address 057
before generating an alarm.
• If a follow zone opens when more than one entry delay zone has
Default: 48 seconds been triggered, the control panel will wait until end of the entry
You can set the Intellizone Time Delay between 010 and 255 delay zone that opened first, before generating an alarm.
seconds. This is the period specified for Intellizones to detect one of
(QWU\ 'HOD\
three conditions before generating an alarm (see Intellizones,
section 7.3). Decimal Programming Î Address 050
[ENT] + [installer code] + [0] [5] [7] + 3-digit decimal value Default: 45 seconds
(010-255) + [ENT] Any zone that has not been identified as Instant Zones, Follow
6LOHQW =RQHV Zones, Entry Delay 2 or “24 Hour” & Fire Zones will automatically

default to Delay 1. You can program the Delay 1 period between
001 and 255 seconds into address 050. If a zone defined as Delay 1
Using the “Feature Select Programming Method”, identify or select opens in an armed system, the control panel will wait the
which zones will be defined as Silent Zones. If an alarm occurs on a programmed period before generating an alarm. This allows time
Silent Zone, the control panel will report the alarm (see Event for users to disarm the system when entering the protected area.
Reporting on section 8) to the central station without triggering any [ENT] + [installer code] + [0] [5] [0] + 3-digit decimal value
bells. If zone 3 is defined as a 24 hour (fire zone), the control panel (001-255) + [ENT]
will generate an audible alarm overriding a silent zone definition.
´ +RXUµ )LUH =RQHV (QWU\ 'HOD\
Using the “Feature Select Programming Method”, identify or select
Using the “Feature Select Programming Method”, identify or select which zones will be defined as Entry Delay 2 Zones. If a zone
which zones will be defined as 24 hour zones. Whether the system defined as Delay 2 opens in an armed system, the control panel will
is armed or disarmed, open “24 hour” zones always generate an wait the Entry Time Delay 2 (see section 7.9.1) period before
alarm. However, if zone 3 is defined as “24 hour”, it becomes a generating an alarm. This allows time for users to disarm the
“Fire Zone”. Connect the smoke detectors as described in section system when entering the protected area.
Fire Circuit. An open “Fire Zone” will generate the following:
• The control panel will send a fire loop trouble report (address
500) to the Central Station.
DE5281 11
Sec. 7.1
Sec. 7.12
Sec. 7.2
Sec. 7.10.1
Sec. 7.10
Sec. 7.10.2
Sec. 7.11
Sec. 7.11.1
Sec. 7.3.1
Sec. 7.3
Sec. 7.4
Sec. 7
Sec. 7.6
Sec. 7.7
Sec. 7.13 Sec. 7.9.1

and 7.14
Sec. 7.9
Sec. 7.8
Sec. 7.8
Figure 25 - Zone Related Features
12 DE5281
7.9.1 Entry Time Delay 2 7.11.1 Auto Zone Shutdown
Decimal Programming ÎAddress 051 Feature Select Programming Î Address 086 key [TRBL]
Default: 45 seconds Default: Disabled
This applies to all zones defined as Delay 2 (see Entry Delay 2 The control panel will automatically bypass any “Bypass Enabled
above). You can program the Delay 2 between 001 and 255 Zones” which initiate 5 consecutive alarms in the same-armed
seconds (default 45 seconds). period. Therefore, the zone will no longer generate an alarm. After
[ENT] + [installer code] + [0] [5] [1] + 3-digit decimal value the control panel has bypassed a zone, it will report an event code
(001-255) + [ENT] to the Central Station if programmed at addresses 448-461 (see
3DUWLWLRQLQJ 0DHVWUR RQO\

Reporting Event Codes, section 8.6).
This feature is a function of the Report Zone Restore Options (see
Feature Select Programming Î Address 086, key [8] section Report Zone Restore Options). If this option is set for
Report zone restore on bell cut-off, the zone will only be bypassed
This feature divides the alarm system into two distinct systems,
identified as “System A” and “System B”. You can assign each after the bell or siren has cut-off 5 consecutive times in the same
zone to System A, System B, both systems, or neither system. armed period. While if the option is set for report zone on zone
Partitioning works as follows: closure, the zone will be bypassed when the zone has opened and
• Zones assigned to System A, will arm/disarm when the system is closed 5 consecutive times in one armed period.
“System A Armed/Disarmed”. LED “TRBL” off: Auto Zone Shutdown Disabled
• Zones assigned to System B, will arm/disarm when the system is LED “TRBL” on: Auto Zone Shutdown Enabled
“System B Armed/Disarmed”. [ENT] + [installer code] + [0] [8] [6] + “TRBL” On/Off + [ENT]
• Zones assigned to both systems (“dual area”) will arm when the
(2/ =RQHV (QDEOHG'LVDEOHG
Î
system is either “System A Armed”, “System B Armed” or when
both systems are armed and will disarm only when both systems Feature Select Programming Address 088; key [MEM]
disarm. Default: EOL input enabled
• Zones not identified to any system (“common area”) will arm only If the system is using 1KΩ end of line resistors on zone input
when the system is both “System A Armed” and “System B terminals, enable this feature (see Zone Connections in section 3.8).
Armed” and will only disarm when at least one of the two systems
disarms. LED “MEM” off: Input Zones use EOL Resistors
For more information on arming and disarming partitions, see LED “MEM” on: Input Zones do not use EOL Resistors
section 12.5, Arming/Disarming Partitions. Also, refer to Code [ENT] + [installer code] + [0] [8] [8] + “MEM” On/Off + [ENT]
Priority in section 9.12.
.H\SDG =RQH 6XSHUYLVLRQ
7.10.1 “System A”/Home Zones
Feature Select Programming Î Address 090, key [home]
Default: Disabled
Using the “Feature Select Programming Method”, select which If using a keypad zone defined as keypad zone 1, enable this
zones will be assigned to “System A” or if the system isn’t feature. When enabled, the control panel will verify for the presence
partitioned the zones will be identified as Home Zones. For details of a keypad and the keypad zone. For more information, see
on “System A” zones refer to Partitioning above. For details on Keypad Zone Connections in section Keypad Zone Connections in
Home Arming (see section 12.4). section 3.8.
7.10.2 “System B” Zones
Î
LED “HOME” off: Keypad Zone 1 Disabled
Feature Select Programming Address 120, keys [1] to [0] LED “HOME” on: Keypad Zone 1 Enabled
Using the “Feature Select Programming Method”, select which [ENT] + [installer code] + [0] [9] [0] + “HOME” On/Off + [ENT]
zones will be assigned to “System B”. For details on “System B”
.H\SDG =RQH 6XSHUYLVLRQ
zones refer to Partitioning above.
Î
%\SDVV (QDEOHG =RQHV
Feature Select Programming Address 090, key [away]
Default: Disabled
Feature Select Programming Î
Address 124, keys [1] to [0] If using a keypad zone defined as keypad zone 2, enable this
feature. When enabled, the control panel will verify for the presence
Using the “Feature Select Programming Method”, select which
zones will be defined as Bypass Enabled. Only zones defined as of a keypad and the keypad zone. For more information, see
bypass enabled can be used for Manual Zone Bypassing (see Keypad Zone Connections in section 3.8.
section 12.9, Manual Zone Bypassing) or during Auto Zone LED “AWAY” off: Keypad Zone 2 Disabled
Shutdown (see section 7.11.1). LED “AWAY” on: Keypad Zone 2 Enabled
[ENT] + [installer code] + [0] [9] [0] + “AWAY” On/Off + [ENT]
(9(17 5(3257,1*
5HSRUWLQJ 2SWLRQV transmission, the control panel will dial the next central station
Feature Select Programming Î Address 086, key [HOME] & [AWAY]

telephone number, as defined by the reporting options and report
only those events not reported during the interrupted attempt. For
Default: Reporting Disabled more information on Reporting Event Codes (see section 8.6).
When a specific event occurs in the system, the control panel will [ENT] + [installer code] + [0] [8] [6] + “HOME” & “AWAY” On/Off +
attempt to report the appropriate event code to the Central Station. [ENT]
The Reporting Options define where the event codes are reported. “HOME “AWAY Reporting Feature
In order to establish communication with the Central Station, the ” ”
control panel will first access a telephone line and wait a maximum
of eight seconds for a dial tone. If a dial tone is recognized or if after OFF OFF Reporting Disabled
eight seconds there is no dial tone, the control panel will dial the OFF ON Regular Reporting
appropriate Central Station Telephone Number as defined by the ON OFF Split Reporting
Reporting Options listed in the table below. Once communication is
ON ON Double Reporting
established, the control panel will transmit the events in the event
buffer to the Central Station. If communication fails during
DE5281 13
Sec. 8.4
Sec. 8.2
Sec. 8.3
Sec. 8.1.1
Sec. 8.1.2
Sec. 8
Sec. 8.1
Sec. 8.1.3
Sec. 8.1.4
Sec. 8.5.3
Sec. 8.5
Sec. 8.5.1
Sec. 8.5.2
Sec. 8.5.4
14 DE5281
8.1.1 Reporting Disabled occurs (reportable or non-reportable), the control panel will begin
the dialing sequence again.
The Control Panel will never transmit any event codes to the central
station. When the system is in alarm, the control panel will report all Event
Codes to Central Station Telephone 1. Any ongoing communication
8.1.2 Regular Reporting will stop immediately and the panel will dial Telephone 1. If
Using regular reporting the event codes are reported to the central communication fails, the dialer will hang-up, wait a pre-determined
station using either telephone number 1 or 2. The control panel will period and dial the number again. The control panel will dial the
begin by dialing central station telephone number 1. If number eight times until communication is established (see figure
communication fails, the dialer will hang up, wait a pre-determined 27). After eight unsuccessful dialing attempts, the redial sequence
period and dial central station telephone number 2. This sequence ends and a "communicator report failure" will appear in the keypad’s
will repeat 4 times, switching back and forth between the 1st and trouble display (LED “7” on). When the next event occurs
2nd number (see figure 27) until communication is established. (reportable or non-reportable), the control panel will begin the dialing
After eight unsuccessful dialing attempts, the redial sequence ends sequence again.
and a "communicator report failure" will appear in the keypad’s 8.1.4 Double Reporting
trouble display (LED “7” on). When the next event occurs
(reportable or non-reportable), the control panel will begin the dialing In double reporting, the control panel will report each event code to
sequence again. both central station telephone numbers. The control panel will begin
by attempting communication with central station telephone 1 and if
8.1.3 Split Reporting communication fails, the dialer will hang-up, wait a pre-determined
When the system is not in alarm, the control panel will report all period and dial the number again. The control panel will dial the
Event Codes to Central Station Telephone 2. If communication fails, number eight times until communication is established (see figure
the dialer will hang-up, wait a pre-determined period and dial the 27). After eight unsuccessful dialing attempts, the redial sequence
number again. The control panel will dial the number eight times ends and a "communicator report failure" will appear in the keypad’s
until communication is established (see figure 27). After eight trouble display (key [7] "on"). If communication has been
unsuccessful dialing attempts, the redial sequence ends and a established and the event codes transmitted or if after eight
"communicator report failure" will appear in the keypad’s trouble attempts communication has not been established, the control panel
display (LED “7” on). When the next event will report the same Event Codes to Central Station Telephone 2.
&HQWUDO 6WDWLRQ 7HOHSKRQH 1R &HQWUDO 6WDWLRQ 7HOHSKRQH 12
Streamline - Section 04 & 05 Î Hexa Programming - Addresses Streamline - Section 06 & 07 Î Hexa Programming - Addresses
016-023 024-031
The control panel will dial the programmed telephone number when The control panel can communicate with two central station
reporting an event code to the central station computer (see numbers depending on the selected Reporting Options in section
Reporting Options in section 8.1). For example, if the alarm 8.1. If the central station does not have a second number, enter the
system is armed and a zone with a motion detector opens, the same number as the first. There is no default telephone number and
control panel will dial the telephone number in order to send the you can enter any number from 0-9 up to a maximum of 16 digits. If
programmed event code to the central station computer. There is no you would like to enter any special keys or functions, refer to table 3
default telephone number and you can enter any number from 0-9 below. If the telephone number contains less than 16 digits, press
up to a maximum of 16 digits. If you would like to enter any special the [TRBL] key to indicate the end of the telephone number.
keys or functions, refer to table 3 below. If the telephone number
contains less than 16 digits, press the [TRBL] key to indicate the [ENT] + [installer code] + [7] + [0] [6] + Telephone Number + [ENT]
end of the telephone number. or [TRBL] if number <16 digits then [ENT].
[ENT] + [installer code] + [7] + [0] [4] + Telephone Number + [ENT] Caution: Both Central Station Telephone Numbers must be
or [TRBL] if number <16 digits then [ENT]. programmed in order for event reporting to function properly!
DE5281 15
Low Battery 498 & 506 Low System Battery 302
Table 3 - Telephone # Special Instructions
AC fail 499 & 507 AC loss 301
Enter special instructions in the telephone numbers using these Fire Loop Trouble 500 & 508 Fire Loop Trouble 373
keys:
Timer Loss / Timer 501 & 509 Time/Date Reset 625
TLM Trouble Restore 511 Telco 1 Fault 351
[BYPASS] = switch from pulse to tone while dialing Test Report 512 Periodic Test 602
[HOME] = * [MEM] = pause 4 seconds Panic #1 (1+3) 513 Panic Alarm 120
[AWAY] = # [TRBL] = end of telephone number Panic #2 (4+6) 514 Medical 100
6\VWHP $FFRXQW &RGHV Panic #3 (7+9) 515 Fire Alarm 110
Î
Duress 520 Duress 121
Streamline - Section 08 Hexa Programming - Addresses Late Close or No 516 & 517 Late to Open/Close 404
032-035 Partial Arming 518 Bypass 570
All report codes are preceded by a 3 or 4-digit system account code Recent Close 519 Open/Close 400
to ensure correct identification to the central station. For example, if Program Change 525 Program Changed 306
a zone opens, the control panel will first send the account code
Please note this format must use a 4-digit system account code
followed by the appropriate report code. In a partitioned system, the
(see section 8.4, System Account Codes). Ademco Contact ID is a
control panel can send a separate account code for each system.
fast communicator format that uses tone dialing instead of pulse
This will identify to the central station from which system the report
dialing. This communicator format also uses a pre-defined list of
code originated. To do so, program a different number into each
industry standard messages and event codes that should suit most
account code. Where account code #1 will represent System “A”
of your basic installation needs. The control panel will automatically
and account code #2 will represent System “B”.
generate the Contact ID event codes for every event in addresses
NOTE: If partitioning is disabled, program the same value for 300 to 527 (see table 5). Therefore, you do not have to program
both account numbers. addresses 300 to 527.
There are no defaults and you can enter any hexa digit from 0 to F.
8.5.2 Ademco Contact ID (programmable codes)
The first 4 digits entered represent System Account Code #1. The
Please note this format must use a 4-digit system account code
final 4 digits entered represent System Account Code #2. Please
(see System Account Codes, section 8.4). Ademco Contact ID is a
note if required, system account codes can have 3 digits. To do so,
fast communicator format that uses tone dialing instead of pulse
press the [2nd] key followed by the 3-digit account number.
dialing. Use the Ademco Contact ID event list of industry standard
[ENT] + [installer code] + [7] + [0] [8] + 4-digit Account Code #1 + messages and event codes in the programming guide to program
4-digit Account Code #2 + [ENT] the desired event codes into addresses 300 to 527.
or
8.5.3 Ademco Express
[ENT] + [installer code] + [7] + [0] [8] + [2nd] + 3-digit Account This high-speed reporting format communicates 2-digit (00 to FF)
Code #1 + [2nd] 3-digit Account Code #2 + [ENT] events programmed at addresses 300 to 527 at a speed of 2
&RPPXQLFDWRU )RUPDWV seconds per event. Unlike the other Ademco formats, the Contact
Î
ID Event Codes are not used. Please note this format must use a
Streamline - Section 09 Hexa Programming - Addresses 038 4-digit system account code (see section 8.4)
Default: Ademco Slow for both numbers 8.5.4 DTMF – no handshake
The following option will determine which format the control panel This format is the same as the Ademco contact ID (programmable
will use to communicate with the Central Station. Using table 4 codes) except there is no verification of the report code sent (no
below, select the appropriate communication format for each Central handshake). Use this format in reporting situations where a central
Station Telephone Number. The first digit will represent the station receiver is not connected to the telephone number. It is also
Communication Format for Central Station Telephone Number 1 useful for personal reporting where a "handshake" is not required.
and the second digit will represent the Communication Format for For example, in "double reporting" mode, the first central station
Central Station Telephone Number 2. Below you will find a brief number can be connected to a receiver, while the second can be
description of all available Communicator Formats. used for personal reporting using "no handshake" format. The panel
[ENT] + [INSTALLER CODE] + [0] [3] [8] + First digit = Central will make two attempts to call the "no handshake" number. Please note
Station Telephone #1 + Second digit = Central Station Telephone this format must use a 4-digit system account code (see section 8.4).
#2 + [ENT] 8.5.5 Standard Pulse Formats
The control panel supports the following pulse reporting formats
(see table 4): Ademco slow, Silent Knight, Sescoa, and Radionics.
5HSRUWLQJ (YHQW &RGHV

Streamline - Sections 11 to 67 Î
Hexa Programming - Addresses
300-527.
An Event Code is a 2-digit hexadecimal value, consisting of
numbers from 00-FF. Each address between 300 and 527
represents a specific event, as described below and in the
“Programming Guide”. When an event occurs in the system, the
8.5.1 Ademco Contact ID (all codes) control panel will send the 2-digit Event Code programmed at the
corresponding address to the central station. The method of Event
Table 5 - Contact ID Event Codes
Code transmission is dependent on the Communicator Formats
System Event Event Code Contact ID Contact ID (see section 8.5) and the Reporting Options (see section 8.1). If
Alarms / Restores 400 to 447 Burglary Zone # 130 using the Ademco Contact I.D. (all codes) format, you do not have
Alarms / Restores on Zone 402, 426 Fire Alarm 110 to program any addresses. If you plan to program most of the event
Arm / Disarm 301 to 349 / Open / Close by user # 401 code addresses, we suggest you use the Hexa Streamlined
Zone Shutdown 448 to 471 Burglary Bypass # 573 Programming Method as described in section 5.2. Otherwise, use
the Hexa Programming Method as described in section 5.1.
Zone Tamper 472 to 495 Sensor Tamper 383
8.6.1 Arming Codes
Î Hexa Programming - Addresses
Zone Tamper Reset 510 Sensor Tamper 383
Auxiliary Power Trouble 496 & 504 System Trouble 300 Streamline - Sections 11 to 23
Bell Disconnect / Max 497 & 505 Bell 1 Trouble 321 300-349.
16 DE5281
Whenever the system is armed, the control panel will send the 501 - Timer Loss: The control panel detects a loss in the panel
programmed event code to the Central Station identifying who or timer.
how the system was armed. 509 - Timer Programmed
8.6.2 Disarming Codes 502 to 503 - Reserved for Future Use
Streamline - Sections 23 to 35 Î Hexa Programming - Addresses 510 - All Tamper/Trouble Codes (see section 8.6.6) have returned
350-399 to "normal".
Whenever the system is disarmed, the control panel will send the 511 - TLM Trouble Restore: Telephone line has restored after the
programmed event code to the Central Station identifying who TLM (see section 11.1) has detected the loss of a telephone line.
disarmed the system. Also refer to section 8.12
8.6.8 Special Codes
8.6.3 Alarm Codes
Streamline - Section 36 to 41 Î Hexa Programming - Addresses
Streamline or Hexa Programming ÎSection 64 to 67 - Addresses
512-527
400-423 Each of the addresses represents a special condition in the system.
Whenever a zone opens while the system is armed, the control When one of these special conditions occur, the control panel will
panel will send the programmed event code to the Central Station report the event code associated with the address.
identifying which zone generated an alarm. 512 – Test Report: The test report has been activated either
8.6.4 Restore Codes manually (see section 8.8, Manual Test Report or automatically (see
Streamline - Sections 42 to 47 Î Hexa Programming - Addresses section 8.7, Auto Test Report).
513 – Panic 1: A User presses keys [1] and [3] to activate a Panic 1
424-447
The control panel will send the programmed event code to the alarm
Central Station as soon as the zone closes after generating an 514 – Panic 2: A User presses keys [4] and [6] to activate a Panic 2
alarm or as soon as the zone closes after bell cut-off. For more alarm
information, please see Report Zone Restore Options in section 515 – Panic 3: A User presses keys [7] and [9] to activate a Panic 3
8.11. alarm.
8.6.5 Shutdown Codes For more information on Keypad Panic Options see section 9.4.
Streamline - Sections 48 to 53 Î Hexa Programming - Addresses 516 – Late To Close: “Timed” Auto Arming is enabled (see
448-471 section 9.1) and the system has not automatically armed itself at the
If the Auto Zone Shutdown feature is enabled (see section 7.11), specified time.
the control panel will send the programmed event code to the 517 – No Movement: “No Movement” Auto Arming is enabled
Central Station identifying which zones were shutdown. (see section 9.2) and no movement has occurred for the designated
8.6.6 Tamper/Trouble Codes amount of time.
Streamline - Sections 54 to 59 Î Hexa Programming - Addresses
518 – Partial Arming: Whenever the system is “Away” armed,
“Home” armed, or armed while one or more zones are bypassed.
472-495
519 – Recent Close: An alarm occurs shortly after the system has
If the Tamper/Wire Fault Recognition Options are disabled (see
been armed (see section 8.10, Recent Close Delay).
section 11.7), the control panel will never transmit these event
codes. Otherwise, whenever a tamper occurs on a zone, the control 520 – Duress: The Duress feature is enabled (see section 4.4) and
panel will send the programmed Event Code to the Central Station a User disarms the system using the User Code #48.
where Tamper 1 to Tamper 4 represent tamper report codes for 521 to 523 – Reserved for Future Use
control panel inputs 1 through 4. With Advanced Technology Zoning 525 – Program Change: The installer code is used to enter the
(ATZ) enabled (see section 7.2) each Tamper Code address will programming mode.
represent two zones (as shown below). The control panel will send 526 to 527 – Reserved for Future Use
$XWR 7HVW 5HSRUW

the programmed Event Code when a tamper occurs on either zone.
472 – Tamper 1 = Input 1 / Zones 1 & 2
474 – Tamper 2 = Input 2 / Zones 3 & 4 Decimal Programming Î Addresses 046-048
476 – Tamper 3 = Input 3 / Zones 5 & 6 Default: Auto Test Report Disabled
478 – Tamper 4 = Input 4 / Zones 7 & 8 The report code programmed at address 512 will be reported to the
8.6.7 Trouble/Restore Codes central station after the number of days programmed at address
Streamline or Hexa Programming Î Section 60 to 63 - Addresses
046 have elapsed and at the time programmed at address 047
(hours) and 048 (minutes). To disable this feature, program 000 at
496-511 address 046. Also note that if [2nd][2nd] is programmed at address
Each of the addresses represents a specific trouble condition. The 512 nothing will be reported.
control panel will report the appropriate event code to the central [ENT] + [installer code] + [0] [4] [6] + 2 digits (days) + [0] [4] [7] + 2
station when one of the following conditions occurs or after the digits (hours) + [0] [4] [8] + 2 digits (minutes) + [ENT]
0DQXDO 7HVW 5HSRUW

condition has returned to normal.
496 - Max. Auxiliary Current: is ≥ 1A.
504 - Max. Auxiliary Current Restore Key Access Programming Î key [BYPASS]
497 - Bell Disconnect/Max. Bell Current: Bell is disconnected or bell Activating the manual test report will send the Event Code
current is ≥ 3A. programmed at address 512 to the Central Station.
505 - Bell Disconnect Restore: No restore code for bell current [ENT] + [Installer, Master, or User 1 Code] + [BYPASS]
498 - Battery Disconnect/Low Voltage: Battery disconnected or battery
3RZHU )DLOXUH 5HSRUW 'HOD\
voltage ≤ 10.5V.
506 - Battery Disconnect/Low Voltage Restore
Decimal Programming Î Addresses 054
Default: 30 minutes
499 - Power Failure: Voltage on AC input is ≤ 12.5V. (Also refer to
section 8.9) After a power failure, the control panel will delay transmission of the
event code programmed at address 499 by the period programmed
507 - Power Failure Restore
at this address (001 to 255 minutes).
500 - Fire Loop Trouble: A tamper occurs on a fire zone (Zone
[ENT] + [installer code]+ [0] [5] [4] + 3-digit decimal value (001-255)
3/24hr.).
+ [ENT]
508 - Fire Loop Trouble Restore
DE5281 17
5HFHQW &ORVH 'HOD\ transmit as soon as the zone returns to normal (zone closure).
Decimal Programming Î Addresses 060

LED “bypass” off: Report Zone Restore on Bell Cut-Off
LED “bypass” off: Report Zone Restore on Zone Closure
Default: Disabled
[ENT] + [installer code] + [0] [8] [8] + “bypass” On/Off + [ENT]
The system will transmit the recent close event code programmed
5HSRUW &RGH 'LVDUPLQJ 2SWLRQV
Î
at address 519 if after arming the system, an alarm occurs within
the period programmed at this address (001 to 255 minutes). Feature Select Programming Address 088; key [TRBL]
Program 000 into address 060 to disable this feature. Default: Disarming Codes Transmit on User Disarming
[ENT] + [installer code] + [0] [6] [0] + 3-digit decimal value With the “TRBL” indicator off, the report codes programmed at
(001-255) + [ENT] addresses 350-399 (see Disarming Codes in section 8.6.2) will
8.11 Report Zone Restore Options transmit whenever a User disarms the system. With the “TRBL”
Feature Select Programming ÎAddress 088; key [bypass] indicator on, the control panel will transmit these codes when a User
disarms a system in alarm.
Default: Zone Restore Codes Transmit on Bell Cut-Off
With the “Bypass” indicator off, the report codes programmed at LED “TRBL” off: Always Report Disarm
addresses 424-447 (see Restore Codes in section 8.6.4) will only LED “TRBL” on: Report Disarm only after alarm
transmit if the zone has returned to normal upon bell cut-off (see [ENT] + [installer code] + [0] [8] [8] + “TRBL” On/Off + [ENT]
section 9.11). With the “bypass” indicator on, the codes will
$50
$50',6$50 $/$50 237,216
´7LPHGµ $XWR $UPLQJ
Auto Arm Time
Timed Auto Arming
Addresses 044 & 045
Addresse 086; [5]
Feature Select Programming Î Address 086, key [5] (sec. 9.1)
(sec. 9.1.1)
Default: Disabled Auto Arming Options

The alarm system will automatically arm itself at a specified time No Movement Auto Address 090 [2]
everyday. Note, as with regular arming, the system will not arm if a Arming (sec. 9.1.2)
zone is open and will report a “late to close” to the central station. If Address 086; [6]
this occurs, the system will not arm until the next day. The type of (sec. 9.2) No Movement Time
Address 055
arming is dependent on the Auto Arming Options (see below). (Sec. 9.2.1)
Code Priority Define
Program the Auto Arm Time as described below. which users can System “A”/Home
9.1.1 Auto Arm Time System “A”/Home Arm Priority
Arm, arm System “B” Addresses 062, 064
The control panel will automatically arm itself at the specified time if or Bypass Zones & 066; all keys
“Timed” Auto Arming (see above) is enabled. The time is (sec. 9.12)
programmed using the 24-hour clock (i.e. 8:00PM = 20:00). There System “B” Arm
are two methods of programming the “Auto Arm Time” as described “One-Key” Regular Priority
below. Arming Addresses 068, 070
• Decimal Programming Î Address 044 & 045 Arm/Disarm
Related
Address 088; [7]
(sec. 9.3)
& 072; all keys
Program the “Auto Arm Time” in hours into address 044 and the
Features Bypass Access
“Auto Arm Time” in minutes into address 045. “One-Key” System Addresses 074, 076
[ENT] + [installer code] + [0] [4] [4] + 3-digit decimal value “A”/Home Arming & 078; all keys
(hours) + [0] [4] [5] + 3-digit decimal value (minutes) + [ENT] Address 088; [8]
• Key Access Programming Î key [9]
(sec. 9.4)
Keyswitch Arming
The User 1, Master, or Installer can program the “Auto Arm Time” using
Address 086;
this method. [2] & [3] (sec. 9.5)
[ENT] + [Installer, Master, or User 1 Code] + [9] + 2 digits
representing hours + 2 digits representing minutes + [ENT] Bell Squawk
Address 086; [MEM]
9.1.2 Auto Arming Options
Î
(sec. 9.6)
Feature Select Programming Address 090, key [2] “Beep” on Exit Delay
Exit Delay
Address 088;
Default: Regular Arming Address 049
[AWAY]
(sec. 9.7)
The “Auto Arm” feature will arm the system as described in the (sec. 9.8)
table below. Alarm Transmission
[ENT] + [installer code] + [0] [9] [0] + “2” On/Off + [ENT] Delay
Address 059
LED “2” Partitioning Option (sec. 9.9)
Off Off “Regular Arming” Bell Cut-Off Time

Off On “System A and B Arming” Address 052
(sec. 9.11)
On Off “Home Arming”
On On “System A Arming” Figure 28 - Arming/Disarming Related Features
18 DE5281
´1R 0RYHPHQWµ $XWR $UPLQJ ([LW 'HOD\
Feature Select Programming Î Address 086, key [6] Decimal Programming Î Address 049
Default: Disabled Default: 60 seconds
If the control panel does not detect any zone openings for a The Exit Delay applies to all zones. This option determines how
specified period, the control panel will arm the system and transmit much time the user has to leave the protected area before the
the event code programmed at address 517. Note the type of system arms after entering a valid access code. You can program
arming is dependent on the Auto Arming Options (see the Exit Delay from 001 to 255 seconds.
above). Program the “No Movement” Auto Arm as described below. [ENT] + [installer code] + [0] [4] [9] + 3 digit decimal value (001-255)
LED “6“ off: No Movement Auto Arm Disabled + [ENT]
LED “6” on: No Movement Auto Arm Enabled
%HHS RQ ([LW 'HOD\
[ENT] + [installer code] + [0] [8] [6] + “6” On/Off + [ENT]
Feature Select Programming Î Address 088, key [away]
9.2.1 “No Movement” Auto Arm Time Default: Disabled
Decimal Programming → Address 055 With this feature enabled, the keypad will sound an intermittent
Default: 8 hours “beep” during exit delay (except when in “HOME” arming).
000 = disabled; (001-255) X 15 minutes Frequency of intermittent beeps increases during the last 10
If the “No Movement” Auto Arming (see above) feature is disabled seconds of the exit delay period.
and a time is programmed, the control panel will transmit the event LED “AWAY” off: Beep on Exit Delay Disabled
code programmed at address 517 if no movement is detected LED “AWAY” on: Beep on Exit Delay Enabled
during the programmed period.
[ENT] + [INSTALLER CODE] + [0] [5] [5] + 3-digit decimal value [ENT] + [installer code] + [0] [8] [8] + “AWAY” On/Off + [ENT]
(001-255) + [ENT]
$ODUP 7UDQVPLVVLRQ 'HOD\
´2QH.H\µ 5HJXODU $UPLQJ Decimal Programming Î Address 059
Feature Select Programming → Address 088, key [7]. This time limit, set between 5 and 63 seconds, is the delay period
Default: Disabled. the control panel will wait before reporting an alarm to the central
A user can “regular” arm the system by pressing and holding the station. During this period, disarming the system will cancel all
[QUICK] key for 2 seconds. pending alarms and send the restore codes. Programming 000-004
LED “7” off: “One-Key” Regular Arming Disabled disables this feature.
LED “7” on: “One-Key” Regular Arming Enabled [ENT] + [INSTALLER CODE] + [0] [5] [9] + 3-digit decimal value
[ENT] + [INSTALLER CODE] + [0] [8] [8] + “7” On/Off + [ENT] (005-063) + [ENT]
´2QH.H\µ +RPH µ6\VWHP $µ 6LOHQW =RQHV 6LOHQW 3DQLFV

$UPLQJ 2SWLRQ
Feature Select Programming → Address 088, key [8]. Feature Select Programming Î Address 086, key [9]
Default: Disabled. If the “9” indicator is on, silent zones or silent panics only transmit a
Press and hold the [HOME] key for 2 seconds to “Home” arm the report to the central station. The system will not indicate an alarm
system if partitioning is disabled. If the system is partitioned, the and will not have to be disarmed, nor will the control panel activate
control panel will arm “System A”. the PGM. If a keypad panic has been defined as audible, the control
LED “8” off: “One-Key” Home/“System A” Arming Disabled panel will override this option.
LED “8” on: “One-Key” Home/“System A” Arming Enabled LED “9” off: Silent Zones & Silent Panics generate a silent alarm
[ENT] + [INSTALLER CODE] + [0] [8] [8] + “8” On/Off + [ENT] LED “9” on: Silent Zones & Silent Panics generate a report only
$UPLQJ 8VLQJ .H\VZLWFK RU [ENT] + [installer code] + [0] [8] [6] + “9” On/Off + [ENT]
3XVKEXWWRQ %HOO &XW2II 7LPH

Feature Select Programming → Address 086, key [2] & [3]. Decimal Programming Î
Address 052
Default: Disabled. Default: 5 minutes
The user can use a keyswitch or pushbutton to “Home” and After an audible alarm, the bell or siren will stop after the
“Regular” arm/disarm the system. Refer to sections 3.7 & 12.8. programmed time has elapsed.
[ENT] + [INSTALLER CODE] + [0] [8] [6] + “2” & “3” On/Off + [ENT] + [installer code] + [0] [5] [2] + 3-digit decimal value
[ENT] (001-255) minutes + [ENT]
Table 6 - Keyswitch Arming Table
&RGH 3ULRULW\
LED “2”
Off
LED “3”
Off Disabled
Function
Feature Select Programming Î Address 062-078, [all] keys
In order for a user to arm a partitioned system, to “Home” arm,
On Off Disabled
“Away” arm or to manually bypass zones, the user must be given
Off On “Regular” Arm code priority. Using the “Feature Select Programming Method”,
On On “Home” Arm identify which arming methods each can use. Users not given code
%HOO 6TXDZN priority can only “regular” arm a non-partitioned system. For more
information on arming/disarming methods please refer to section 12,
Feature Select Programming Î Address 086; key [MEM] User/Keypad Functions.
• Partitioning Disabled:
Default: Disabled
Addresses 062-066: Lit LEDs denote which user codes can
With this feature enabled, the bell or siren will sound a half-second
activate "Home" arming.
“squawk” upon arming and two half-second “squawks” upon
disarming. Addresses 068-072: Lit LEDs denote which user codes can
LED “MEM” off: Bell Squawk Disabled activate "Away” arming.
LED “MEM” on: Bell Squawk Enabled Addresses 074-078: Lit LEDs denote which user codes can
"Bypass" zones.
[ENT] + [INSTALLER CODE] + [0] [8] [6] + “MEM” On/Off + [ENT]
DE5281 19
• Partitioning Enabled:
arm “System A".
arm “System B".
"bypass" zones.

3*0 SURJUDPPDEOH RXWSXWV
3*0 7\SHV
Streamline - Sections 09 Î Hexa Programming - Address 039
The MAESTRO control panels have one programmable output
(PGM). When a PGM closes, ground is supplied to activate any
device or relay connected to it, providing up to a maximum of 50mA.
When a PGM opens, the circuit is opened from ground, therefore
not providing any power to devices connected to it. To program a
PGM you must define the PGM state (normally open or normally
closed), the timing (regular or timed) and you must define the type
of logic (“OR”, “AND”, “EQUAL”). To do so, use table 7 to determine [ENT] + [INSTALLER CODE] + [0] [3] [9] + one digit from table 7 +
which hexa digit to program into address 039, where the first hexa [2ND] + [ENT]
digit programmed corresponds to the PGM.
• 3*0 7LPHU 6HWWLQJ
Î
Regular N.O./N.C.
A triggered PGM will switch to its opposite state (i.e. closed to Decimal Programming Address 056
open or opened to closed). The PGM will return to its original Default: 5 seconds
state once the event(s) that triggered it have terminated.
• Timed N.O./N.C You can program the PGM Timer from 1 to 127 seconds or 1 to 127
A triggered PGM will switch to its opposite state (i.e. closed to minutes. To determine the 3-digit decimal value, do the following:
open or opened to closed). The PGM will remain in its • To program in seconds, the required time is respective to the
opposite state for the period programmed at address 056. See decimal value
“PGM Timer Setting” in section 10.2 for details. If the PGM is 1 second = 001, 55 seconds = 055, 127 seconds = 127.
triggered again before the period has elapsed, the PGM will • To program in minutes, add the desired minutes to 128:
remain in its opposite state and the timer will be reset. 5 minutes: 128 + 5 = 133
• “OR” Logic 127 minutes: 128 +127 = 255
Will trigger a PGM when at least one event occurs from a [ENT] + [INSTALLER CODE] + [0] [5] [6] + 3-digit decimal value
specific group of events (e.g. key [1] and/or [2] is pressed on (001-255) + [ENT]
the keypad).
• “AND” Logic
The “AND” logic will trigger a PGM when all events, or more,
occur from a specific group of events (e.g. Keys [1] and [2] are
pressed simultaneously. Note that pressing those two keys in
conjunction with any other key will also trigger the PGM).
• “EQUAL” Logic
The “EQUAL” logic will trigger a PGM only when the events
from a specific group of events occur (e.g. Keys [1] and [2] are
pressed). Note the PGM will only trigger when pressing keys
[1] and [2] simultaneously, if any other key is pressed at the
same time (e.g. [1], [2] & [3]) the PGM will not trigger.
20 DE5281
3*0 2SWLRQV The PGM options define which sequence of events will trigger the
Streamline or Hexa Programming Î Section 10 - Addresses 040 & PGM. The PGM options are virtually endless, therefore, to list them
in the manual is impractical. Table 8, contains a list of the most
042 commonly used PGM options with the required 2-digit data for each
address.

27+(5 237,216
7HOHSKRQH /LQH 0RQLWRULQJ 7/0 LED “3” on = Panic 3 (keys [7] and [9]) enabled
Feature Select Programming Î Address 086, key [2ND] & [1] Keypad panic options:
LED “4” off = Panic 1 silent
Default: TLM Disabled
LED “4” on = Panic 1 audible
When enabled, the system verifies the existence of a telephone line
every 4 seconds. After each successful test, the dialer LED (green LED “5” off = Panic 2 silent
light) on the control panel flashes briefly. If the test fails the led LED “5” on = Panic 2 audible
flashes on and off until the control panel detects the telephone line LED “6” off = Panic 3 silent
again. TLM will activate a trouble when less than 3 volts is detected LED “6” on = Panic 3 fire alarm
in four consecutive tests. Note, when the dialer detects a telephone Silent operation:
ring, the TLM test stops for 1 minute.
When using the panic keys, the control panel will sound a single
There are three TLM options, which are set as indicated in table confirmation beep. The control panel will transmit the event codes
number 9: programmed at addresses 513, 514, and 515. The alarm will latch
1. OFF/ON: Line test failure will generate a trouble indication; “10” (no audible alarm) and the "armed" light on the keypad will flash until
indicator will illuminate on the keypad. the system is disarmed by a valid User code.
2. ON/OFF: Line test failure will generate a trouble indication and Audible operation:
an alarm if the system is armed. Same as silent operation, except the alarm output (bell/siren) will
3. ON/ON: Line test failure will generate a trouble indication and activate until the system is disarmed by a valid User code or until
cause a silent zone or a silent panic alarm to switch to audible the Bell Cut-Off Time (see section 9.11) elapses.
mode. Fire operation:
[ENT] + [INSTALLER CODE]+ [0] [8] [6] + “2ND" & “1” On/Off + Same as audible operation except that bell/siren output will be
[ENT] pulsed (intermittent "on"/"off").
3DQHO 7LPH

Key Access Programming Î
key [MEM]
To program the current time into the control panel press:
[ENT] + [Installer, Master, or User 1 Code] + [MEM] + 2 digits
representing hours (00-23) + 2 digits representing minutes (00-59)
7LPH &RUUHFWLRQ

Streamline - Section 09 Î
Hexa Programming - Address 037
If you notice a gain or loss in the control panel time, calculate the
average gain or loss per day and select the “opposite” amount from
'LDOLQJ 2SWLRQV the Time Correction table in order to automatically correct the time
Feature Select Programming ÎAddress 086, key [7]

setting every 24 hours.
Example: The control panel loses 4 minutes per month,
Default: Pulse Dialing representing an average loss of 8 seconds per day. Therefore,
You can program the control panel to use the pulse dialing or program [2] (plus 8 seconds) as the second digit in address 037 to
tone/DTMF dialing format. compensate for the 8-second loss.
LED “7” off: Pulse Dialing Table 2 - Answering Machine Override Options
LED “7“ on: Tone/DTMF Dialing [2nd] or [1] = Answering Machine Override disabled
[ENT] + [INSTALLER CODE] + [0] [8] [6] + “7” On/Off + [ENT] [2] = 16 sec. [4] = 32 sec. [6] = 48 sec. [8] to [TRBL] = 60 sec.
'LDOLQJ 3XOVH 5DWHV [3] = 24 sec. [5] = 40 sec. [7] = 56 sec.

(address 037 second digit)
Table 10 - Time Correction
Default: Pulse USA 1:1.5 [2nd] - No adjustment [8]- Minus 4 seconds

This selection reflects the ratio between “pulse” time and "quiet" [1]- Plus 4 seconds [9]- Minus 8 seconds
time. Select Pulse Europe for a 1:2 ratio and select Pulse USA for [2]- Plus 8 seconds [0]- Minus 12 seconds
1:1.5. [3]- Plus 12 seconds [HOME] - Minus 16 seconds
LED “10” off: Pulse Europe 1:2 [4]- Plus 16 seconds [AWAY] - Minus 20 seconds
LED “10” on: Pulse USA 1:1.5 [5]- Plus 20 seconds [BYPASS] - Minus 24 seconds
[ENT] + [INSTALLER CODE] + [0] [8] [6] + “10” On/Off + [ENT] [6]- Plus 24 seconds [MEM] - Minus 28 seconds
.H\SDG 3DQLF 2SWLRQV

[7]- Plus 28 seconds [TRBL] - Minus 32 seconds
7DPSHU:LUH )DXOW 5HFRJQLWLRQ

Feature Select Programming Address 088 keys [1] to [6]
2SWLRQV
Î
This feature will generate an alarm when the User presses two
specific keys on the keypad simultaneously for 2 seconds as Feature Select Programming Address 088, keys [0] and [HOME]
described below: When the control panel detects an open or a short on a zone, it will
LED “1” on = Panic 1 (keys [1] and [3]) enabled report this in the following manner. When the system is armed,
LED “2” on = Panic 2 (keys [4] and [6]) enabled regardless of the tamper/wire settings it will always generate an
DE5281 21
alarm and trouble indicator (LED “9”). Alarms will be audible or
,QVWDOOHU 7HVW 0RGH
silent depending on individual zone definitions. If an open or short
occurs on a disarmed system, the control panel will generate an Key Access Programming Î key [8]
incident depending on the following settings: The “Installer Test Mode” will allow you to perform walk tests where
“10” “HOME” Tamper Recognition Option the bell or siren will squawk to indicate opened zones. To enter or
OFF OFF Tamper/Wire Fault Disabled
exit the control panel “Test Mode” press:
[ENT] + [INSTALLER CODE] + [8] to enable; press [8] again to disable
OFF ON Trouble Enabled
ON OFF Silent Alarm Enabled ([FOXGH 3RZHU )DLOXUH )URP
ON ON Audible Alarm Enabled
7URXEOH 'LVSOD\
Tamper/Wire Fault Disabled:
Tamper/wiring failure recognition is disabled. Feature Select Programming Î
Address 090, key [2nd]
Trouble Enabled: Default: disabled
Tamper/wiring failure will generate a trouble indicator (LED “9”) and Excludes the Power Failure, LED “2”, from the Trouble Display (see
a trouble report code (see Tamper/Trouble Codes , in section 8.6.6) section 12.12.2).
when the system is disarmed.
Silent Alarm Enabled $XGLEOH 7URXEOH :DUQLQJ
Tamper/wiring failure will generate a trouble indicator (LED “9”), a Feature Select Programming Address 090, key [9]
trouble report code (see Tamper/Trouble Codes, in section 8.6.6 ) Default: Disabled
and a silent alarm (no bells/sirens) Trouble conditions will sound an intermittent “beep” on the keypad.
Audible Alarm Enabled: To silence the trouble warning, press the [TRBL] key.
Tamper/wiring failure will generate a trouble indicator (LED “9”), a
trouble report code (see Tamper/Trouble Codes , in section 8.6.6) 3RZHU 'RZQ 5HVHW
and an audible alarm. Performing a power down reset will set the installer and master
NOTE: When the zone definition is "24 hour", the tamper definition codes to factory default. Values entered at addresses 008-043,
follows the audible/silent alarm definition of the "24 hour" zone. 062-126, 300-527, as well as all the user codes, will be erased
7DPSHU %\SDVV 2SWLRQV ([2ND], [2ND]). Programmed values of all other addresses do not
Î
change. Note to perform a reset the installer lock must be disabled.
Feature Select Programming Address 090, key [6] To perform a power down reset perform the following:
With this option enabled (LED “6” on), the control panel will not 1. Make sure the installer lock is disabled (see section 4.5)
generate an alarm if a tamper is detected on a bypassed zone while 2. Remove the battery and AC power from the control panel.
the system is armed. With the option disabled, the control panel will 3. Set the “reset” jumper to on. Place a jumper on the “reset” pins
generate an alarm if a tamper or wire fault is detected on bypassed of the control panel.
zone when the system is armed.
4. Re-connect the AC power and the battery to the control panel.
LED “6“ off: Alarm if Tamper on Bypassed Zone
5. Wait 10 seconds and remove the jumper.
LED “6” on: No Alarm if Tamper on Bypassed Zone
[ENT] + [INSTALLER CODE] + [0] [9] [0] + “6” On/Off + [ENT]

86(5
86(5.(<3$' )81&7,216
The innovative Maestro keypad takes a new approach to security
features and functions. Each LED indicator from 1 to 10 on the
5HJXODU $UPLQJ
keypad, respectively, represents each zone on the control panel. “READY” indicator on + [valid access code]
When zone indicator is “off”, the status in the protected zone is This method, commonly used for day-to-day arming, will arm all the
normal. If the zone indicator is “on”, this means the zone is open. zones in the system. To do so, the keypad’s green “READY” light
The green “READY” indicator on the keypad will illuminate when the must be illuminated, indicating that all zones are closed. All doors
status of all the zones is normal (zones are closed). Therefore, all and windows must be closed, and there can be no movement in
windows and doors must be closed and motion detectors must not areas monitored by motion detectors. Once the “READY” light is on,
detect any movement except those zones that have been bypassed. a valid user access code must be entered. If a mistake is made
entering the code or if the “READY” indicator is not on when the
Confirmation Beep: an intermittent series of beeps
code was entered, the keypad will sound a “rejection beep”
(“beep-beep-beep”) indicating a successful keypad entry or system
(beeeeeeeep).
operation.
When the correct user access code is entered, the keypad will
End/Rejection Beep: one long tone (“beeeeeeep”) indicating
sound a “confirmation beep” (beep-beep-beep) and the red "arm"
incorrect keypad entry or unsuccessful system operation.
3URJUDPPLQJ 0DVWHU 8VHU indicator will illuminate. The “READY” light will flash and the keypad
will "beep" during the exit delay period (see section9.7). During the
&RGHV final 10 seconds of the exit delay, the keypad will “beep” and the
“READY” indicator will flash at a faster rate. At the end of the exit
The Maestro control panels have one Master (00) code and up to 48 delay, the keypad will sound a “confirmation beep”, the green
User (01-48) codes. The default Master code is 0000. The Master “READY” indicator will extinguish and the red “ARM” indicator will
code can arm the system using any arming method, can remain illuminated to indicate that the system is armed.
create/modify user codes and can perform Key Access
Programming (see section 12.13). The User 1 code can
12.2.1 “One-Key” Regular Arming
“ready” indicator on + hold the [quick] key for 2 seconds
create/modify access codes and perform key access programming.
The access code consists of either 4 or 6-digits and each digit can To use this feature, enable the “One-Key” Regular Arming option
be any value from 0 to 9. Note, do not enter [2nd] when (see section “One-Key” Regular Arming). When the green "ready"
programming the master code as this will invalidate the master light is on, pressing and holding the [quick] key for 2 seconds will
code. arm all zones in the system. This feature can be used to allow
specific individuals like service personnel (i.e. cleaners,
[ENT] + [Master or User 1 Code] + 2-digit code number (00-48) + 4
maintenance) to arm the system when leaving the protected area,
or 6-digit access code + [ENT]
without giving them access to any other control panel operations.
22 DE5281
The use of a valid access code is still required to disarm the armed premises and keep the system armed.
system. For details on “Regular Arming”, refer to section 12.2. This can be done one of two ways:
$ZD\ $UPLQJ • With the system already “HOME” armed, press and hold the
[HOME] key for 2 seconds. The system will switch to exit delay
[away] + [valid access code] mode (green “READY” indicator flashes). At the end of the exit
To rapidly arm the system without having to wait for the green delay period, the system will return to “HOME” arm mode.
“ready” indicator, simply press the [away] key followed by a valid • With the system already “HOME” armed, press and hold the
access code. Once the exit delay expires, any open zones will be [QUICK] key for 2 seconds. The system will switch to exit delay
considered “deactivated” by the control panel. Therefore, these mode (green “READY” indicator flashes). At the end of the exit
zones will not generate an alarm. If during this period a “deactivated” delay period, the system will “regular” arm the system (see
zone is closed, the control panel will revert that zone to “active” section 12.2).
$UPLQJ'LVDUPLQJ 3DUWLWLRQV

status, hence, will generate an alarm if breached.
If a mistake is made entering the code, the keypad will sound a
“rejection beep” (beeeeeeeep). When the correct user code is • Thanks to Maestro’s partitioning feature, two distinct systems
entered, the keypad will sound a “confirmation beep” (A and B) can be created and controlled by the control panel.
(beep-beep-beep) and the red "arm" indicator will illuminate. The Partitioning can be used in installations where shared security
"ready" light will flash and the keypad will "beep" during the exit systems are more practical, such as office/warehouse buildings,
delay period (see section 9.8). During the final 10 seconds of the or apartment/condominium complexes. Each zone can be
exit delay, the keypad will “beep” and the “READY” indicator will assigned to System A, System B, both systems or given no
flash at a faster rate. At the end of the exit delay, the green system assignment. User access codes can also be
“READY” indicator will stop flashing and the red “ARM” indicator will programmed to arm/disarm one system or both systems
remain illuminated. If programmed at address 518, the control panel simultaneously (see Code Priority in section 9.12). Unlike
will send a “partial arm” report code to the central station. Note, to regular arming, the green “ready” indicator does not have to be
use this method the user must have “AWAY” arming priority, see illuminated. All doors and windows pertaining to the desired
Code Priority in section 9.12. system must be closed, and there can be no movement in areas
+RPH $UPLQJ monitored by motion detectors in the desired system.
1. If a user is not given any code priorities, the user will never be
[home] + [valid access code]
able to arm or disarm the system when partitioned.
“Home” arming allows the user to remain in the protected area while
2. If a user is given code priority to one of the two systems,
partially arming the system. This means that they can stay in and
entering the correct access code will arm or disarm the
move around the establishment, while certain designated zones are
system to which the user was given priority.
armed. For example, entry/exit points like doors or windows, the
basement, or perhaps all the zones on the perimeter of the 3. If a user is given code priority to arm/disarm both systems A & B,
establishment may be armed when going to sleep at night, while the it will function as follows:
other zones remain deactivated. To program which zones will be • If the User enters the correct access code when
activated when “home arming” the system refer to “System systems "A" and "B" are disarmed, it will completely arm
A”/Home Zones in section 7.10.1. Also note that fire zones must be both systems.
programmed as “home zones”; they can not be bypassed. • If the User enters the correct access code when
Unlike regular arming, the green “READY” indicator does not have to systems "A" and "B" are armed, it will completely disarm
be illuminated. Only doors and windows programmed as “home both systems.
zones” must be closed, and there can be no movement in areas • When the system is partially armed, (i.e. only System "A"
monitored by motion detectors in “home zones”. To “HOME” arm or only System "B" is armed) entering the correct access
the system, press the [home] key followed by a valid access code. If code will arm the other system.
a mistake is made entering the code or if a “home zone” is open • To arm/disarm each system separately, do the following:
when entering the code, the keypad will sound a “rejection beep” • Press [HOME] + [VALID ACCESS CODE] to arm/disarm
(beeeeeeeep). After entering the correct user access code, the "System A".
keypad will sound a “confirmation beep” (beep-beep-beep), the red • Press [AWAY] + [VALID ACCESS CODE] to arm/disarm
“HOME” and "arm" indicators will illuminate and the green "ready" "System B".
indicator will flash during the exit delay period. During the final 10 If a mistake is made entering the code or if a zone in the desired
seconds of the exit delay, the “ready” indicator will flash at a faster system is open when entering the code, the keypad will sound a
rate. At the end of the exit delay, the keypad will sound a “rejection beep” (beeeeeeeep). When the access code is correctly
“confirmation beep”, the “ready” indicator will stop flashing and the entered, the keypad will sound a “confirmation beep”
red “HOME” and “arm” indicators will remain illuminated. Note, to (beep-beep-beep). The keypad can display the status of both
use this method the user must be given “HOME” arming priority, systems. When “System A” is armed, the red “HOME” and “arm”
see Code Priority in section 9.12. indicators will remain on. If System B is armed, the red “AWAY” and
12.4.1 “One-Key” Home Arming “arm” indicators will remain on. When both systems are armed, all
hold the [home] key for 2 seconds three lights will remain on.
To use this feature, enable the “One-Key” Home/System Arming 12.5.1 One-Key “System A” Arming
option (see section “One-Key” Home/System Arming). When all This feature allows the user to arm “System A” without the use of an
“homes zones” are closed, pressing and holding the [home] key for access code. To use this feature, enable the “One-Key”
2 seconds will arm only zones programmed as “home zones”. For Home/”System A” option (see section“ One-Key” Home/”System
details on “Home Arming”, refer to section 12.4. A”). When all the zones in “System A” are closed, press and hold
12.4.2 “One-Key” Double Home Arming the [home] key for 2 seconds to arm “System A”. This feature can
After having “HOME” armed the system (see section 12.4), press be used to allow specific individuals like service personnel (i.e.
and hold the [home] key for 2 seconds during the exit delay, until cleaners, maintenance) to arm the system when leaving the
you hear a single “beep”. This will switch all “entry delay” zones to protected area, without giving them access to any other control
“instant” zones (see section 7.6). Therefore, any entry delay zone panel operations. For “System A” Arming details refer to sec. 12.5.
that is breached will immediately generate an alarm instead of
waiting a pre-determined period.
6\VWHP 'LVDUPLQJ
The user must enter the protected area through a designated
12.4.3 Fast Exit entry/exit point. The keypad will "beep" during the entry delay
This feature is only available when the system is “Home” armed reminding the user to disarm the system. Upon entry of a valid
(see section 12.4). This feature will allow you to exit the already access code, the red "arm" indicator will extinguish and the keypad
DE5281 23
will sound a confirmation "beep" (beep-beep-beep) denoting the will be erased. By using the “bypass recall” feature, you can
system has been disarmed. If an incorrect access code is entered, reinstate the previous bypass entries saved in memory. While in the
the keypad will sound a rejection "beep" (beeeeeeeep). Press the “bypass mode”, press the [bypass] + [ENT] keys and the previous
[CLR] key at any time to clear data and re-enter another access bypass status will be re-established. This eliminates the need to
code. If an alarm was generated from a fire or 24-hour zone while re-enter the bypass entries every time the system is armed. If a
the system was armed, entering a valid user code will silence the user is in the process of entering new bypass entries on the
siren. However, you should then check the zone and eliminate the keypad, pressing the [bypass] key will override new information and
cause of the alarm. 24-hour zones that restore and re-alarm will reinstate previous bypass entries.
cause another alarm 30 seconds after an access code is entered to
silence the alarm. If you are unable to pinpoint the reason for the .H\SDG &KLPH =RQHV
alarm, call your installer. A chimed zone "advises" you when a zone is opened by creating a
$ODUP 0HPRU\ rapid intermittent beep tone (beep-beep-beep). Up to six zones plus
the local keypad zone can be programmed as chime zones. To turn
on the "chime zone" feature, press and hold the key corresponding
If an alarm situation occurs when the system is armed, the “MEM”
indicator on the keypad will illuminate. A record of all alarm to the desired zone ([1] to [6]) for three seconds until the intermittent
situations that occur is stored in memory. After disarming the chime beep is heard. This means that the chime feature has been
system, pressing once on the [MEM] key will display which zones activated. If a continuous beep is heard, this means that the chime
were open during the alarm period by illuminating the corresponding beep has been deactivated. To enable the chime feature on the
zone indicator(s). Please note that if the [MEM] key is pressed keypad zone, press and hold the [8] key for three seconds. To mute
again you will enter the event display which can not decoded. To exit the keypad’s alarm sounder, press and hold the [9] key for three
alarm memory display, press the [CLR] key. seconds until the intermittent chime beep is heard. This means that
.H\VZLWFK RU 3XVKEXWWRQ $UPLQJ

the muting feature has been activated. If a continuous beep is
heard, this means that the muting feature has been deactivated. To
'LVDUPLQJ enable chiming when there is no AC power (orange “power” LED

off) press and hold the [7] key for 3 seconds until the intermittent
A keyswitch or push button can be used to “Home” (section 12.4) or chime beep is heard. If there is more than 1 keypad in the system,
“Regular” (section Regular Arming) arm/disarm the system. If the please "chime" program each keypad separately. Keypad chimes
system is ready and the button is pressed, the system will arm. must be reprogrammed if the panel suffers a total power loss.
Pressing the button again will disarm the system. If a “Home” armed Key [1]-[6]: Turns chime "on" or "off" in zones numbered 1-6
system is in entry delay or if an alarm has been generated while Key [7]: Turns chime “on” or “off” when there is no AC power
“Home” armed, the keyswitch or push button can not be used to (orange “power” LED off)
disarm the system. In this case, only a keypad can disarm the Key [8]: Turns chime "on" and "off" for the local keypad zone
system. In a partitioned system the keyswitch or push button will Key [9]: Turns the keypad’s alarm sounder muting "on" or "off"
7URXEOH 'LVSOD\ 0RQLWRULQJ

arm/disarm “System A” regardless of the “System B” status. To
enable this feature and set the options (home or regular arming)
refer to Arming Using Keyswitch in section 9.5. Trouble conditions are continuously monitored by the control panel
0DQXDO =RQH %\SDVVLQJ which are displayed on the keypad. When a trouble condition
occurs, the “TRBL” indicator will illuminate and the keypad will
[bypass] + [valid access code] + [zones to bypass] + [ENT] sound an intermittent beep if the Audible Trouble Warning (see
When a zone is bypassed it will no longer be monitored by the section 11.11) is enabled. Press the [trbl] key to switch to “trouble
control panel, hence, will not generate an alarm. A user may wish to display” mode. The “TRBL” indicator will flash and any illuminated
bypass certain zones when, for example, workers are renovating keys correspond to a trouble condition as described below. Press
part of their establishment or if a component in their system is any key to exit “trouble display” mode.
damaged. Manual bypass arming instructs the control panel to
ignore (“deactivate”) specified zones in order to arm the remainder
12.12.1 No Battery/Low Battery – “1”
The control panel conducts a dynamic battery test under load every
of the system. In order for a user to bypass any zones, verify that
60 seconds. The illumination of the “1” indicator denotes that the
the following options are set in the control panel:
back-up battery is disconnected or that the battery should be
• You must first define which zones are Bypass Enabled Zones
replaced, as it will not provide adequate back-up current in case of
(see section 7.11). Zones not identified as Bypass Enabled can
AC loss. If the control panel is currently running on battery power,
not be bypassed.
the illumination of the “1” indicator denotes that the battery voltage
• Only users with Code Priority (see section 9.12) can bypass
has dropped to 10.5 VDC or lower.
zones.
• Please note, the control panel can not bypass fire zones. 12.12.2 Power Failure – Key “2”
To bypass zones, press the [bypass] key followed by a valid access The control panel conducts a dynamic battery test under load every
code. If the wrong code was entered or a code without bypass 60 seconds. The control panel will detect a power loss if a
priority, the keypad will sound a “rejection beep” (beeeeeeep). If the continuous loss of AC (≤12.5VAC) has occurred during the period
correct code is entered, the yellow “bypass” light will flash to between two AC power tests (64 to 116 seconds). If a power loss
indicate that you are now in “bypass mode”. If there are any remains present throughout the Power Failure Report Delay (see
currently bypassed zones, their respective zone indicators will turn section 8.9), the control panel will transmit the report code
on. Press the key corresponding to the zone you wish to bypass programmed at address 507 and the “TRBL” indicator will flash
until their respective zone indicator turns on. For example, press the rapidly indicating a power failure. The trouble indicator is restored if
[1] key until the red “1” indicator turns on, indicating that zone 1 is AC is detected during the dynamic battery test. You can remove the
bypassed. If the zone you wish to bypass has not been power failure trouble indicator from the trouble display by enabling
programmed as “bypass enabled”, the corresponding zone indicator the Exclude Power Failure From Trouble Display option (see section
will never illuminate. Press the [CLR] key to erase the current zone 11.10).
bypass entries and exit the “bypass mode”. If you have entered the 12.12.3 Bell Disconnected – “4”
correct bypass entries, press the [ENT] key to accept these entries. The illumination of the “4” indicator denotes that there is no bell or
The yellow “bypass” indicator will remain on, denoting that zones in siren connected to the bell output terminals of the control panel.
the system are currently bypassed, hence, the next time the system Please note that when connecting a bell or siren to an optional relay
is armed, certain zones will be bypassed. output the trouble indicator will always be on. To avoid this, connect
%\SDVV 5HFDOO a 1KΩ resistor across the bell output. The control panel only
recognizes bells or siren connected directly to the bell output of the
This feature permits users to reinstate the last zone bypass entries control panel not those connected through a relay.
saved in memory. When the system is disarmed, the bypass entries
24 DE5281
12.12.4 Maximum Bell current – “5” connections must use EOL resistors (see section 3.9, Zone Input
The bell output is microprocessor controlled and will automatically Terminal Connections).
shutdown when the current exceeds 3A upon alarm. If this occurs, 12.12.9 Telephone Line Monitoring – “10”
the “5” indicator will illuminate. After opening the short or reducing If the Telephone Line Monitoring (TLM) feature (see section 11.1) is
the load, the bell current is restored upon the following alarm enabled, the “10” indicator will illuminate to indicate that the control
generation. panel has not detected the presence of a telephone line for 30
12.12.5 Maximum Auxiliary Current – “6” seconds.
The illumination of the “6” indicator denotes that the auxiliary current 12.12.10 Fire Trouble – “HOME”
has exceeded 1A. This will cause automatic shutdown of the The illumination of the “HOME” indicator denotes a tamper on zone
auxiliary output. After opening the short or reducing the load, the 3, if identified as a fire zone (see section 7.5, “24 Hour” & Fire
control panel will restore power to the auxiliary output following the Zones).
dynamic battery test (approximately 60 seconds).
12.13 Key Access Programming
12.12.6 Communicator Report Failure – “7” This method allows for quick programming of features without
If the control panel was unsuccessful at attempting communication entering addresses or section numbers. The following features are
with the central station computer, the “7” indicator will illuminate. programmed using the installer code as well as the master code and
12.12.7 Timer Loss – “8” user 1 codes.
The illumination of the “8” indicator denotes that the timer must be Auto Arm Time: for details see page section 9.1.1
re-programmed. To re-program the timer press: Panel Time: for details see page section 11.5
[ENT] + [Installer, Master or User 1 Code] + [MEM] + 2 digits (00 to Manual Test Report: for details see page section 8.8
23) representing hours + 2 digits (00 to 59) representing minutes. Installer Test Mode: for details see page section 11.9
Cancel Communication Attempts:
12.12.8 Tamper/Zone Wiring Failure – “9” To cancel communication attempts until the next reportable event
If the Tamper/Wire Fault Recognition Options (see section 11.7) are press: [ENT] + [INSTALLER CODE] + [HOME]
enabled, the “9” indicator will illuminate to indicate a short or cut on
a zone input. In order to provide line short recognition the zone
:$55$17<
Visonic Ltd. and/or its subsidiaries and its affiliates ("the Manufacturer") warrants its The Manufacturer does not represent that its Product may not be compromised and/or
products hereinafter referred to as "the Product" or "Products" to be in conformance with circumvented, or that the Product will prevent any death, personal and/or bodily injury
its own plans and specifications and to be free of defects in materials and workmanship and/or damage to property resulting from burglary, robbery, fire or otherwise, or that the
under normal use and service for a period of twelve months from the date of shipment by Product will in all cases provide adequate warning or protection. User understands that a
the Manufacturer. The Manufacturer's obligations shall be limited within the warranty properly installed and maintained alarm may only reduce the risk of events such as
period, at its option, to repair or replace the product or any part thereof. The Manufacturer burglary, robbery, and fire without warning, but it is not insurance or a guarantee that
shall not be responsible for dismantling and/or reinstallation charges. To exercise the such will not occur or that there will be no death, personal damage and/or damage to
warranty the product must be returned to the Manufacturer freight prepaid and insured. property as a result.
This warranty does not apply in the following cases: improper installation, misuse, The Manufacturer shall have no liability for any death, personal and/or bodily injury
failure to follow installation and operating instructions, alteration, abuse, accident or and/or damage to property or other loss whether direct, indirect, incidental,
tampering, and repair by anyone other than the Manufacturer. consequential or otherwise, based on a claim that the Product failed to function.
This warranty is exclusive and expressly in lieu of all other warranties, obligations or However, if the Manufacturer is held liable, whether directly or indirectly, for any loss or
liabilities, whether written, oral, express or implied, including any warranty of damage arising under this limited warranty or otherwise, regardless of cause or origin,
merchantability or fitness for a particular purpose, or otherwise. In no case shall the the Manufacturer's maximum liability shall not in any case exceed the purchase price of
Manufacturer be liable to anyone for any consequential or incidental damages for breach the Product, which shall be fixed as liquidated damages and not as a penalty, and shall
of this warranty or any other warranties whatsoever, as aforesaid. be the complete and exclusive remedy against the Manufacturer.
This warranty shall not be modified, varied or extended, and the Manufacturer does not Warning: The user should follow the installation and operation instructions and among
authorize any person to act on its behalf in the modification, variation or extension of this other things test the Product and the whole system at least once a week. For various
warranty. This warranty shall apply to the Product only. All products, accessories or reasons, including, but not limited to, changes in environmental conditions, electric or
attachments of others used in conjunction with the Product, including batteries, shall be electronic disruptions and tampering, the Product may not perform as expected. The
covered solely by their own warranty, if any. The Manufacturer shall not be liable for any user is advised to take all necessary precautions for his /her safety and the protection of
damage or loss whatsoever, whether directly, indirectly, incidentally, consequentially or his/her property.
otherwise, caused by the malfunction of the Product due to products, accessories, or 6/91
attachments of others, including batteries, used in conjunction with the Products.
VISONIC LTD. (ISRAEL): P.O.B 22020 TEL-AVIV 61220 ISRAEL. PHONE: (972-3) 645-6789, FAX: (972-3) 645-6788
VISONIC INC. (U.S.A.): 10 NORTHWOOD DRIVE, BLOOMFIELD CT. 06002-1911. PHONE: (860) 243-0833, (800) 223-0020 FAX: (860) 242-8094
VISONIC LTD. (UK): UNIT 1, STRATTON PARK, DUNTON LANE, BIGGLESWADE, BEDS. SG18 8QS. PHONE: (01767) 600857 FAX: (01767) 601098
VISONIC LTD. 1998 MAESTRO-600, MAESTRO-1000 DE5281- (REV. 0, 8/98)
DE5281 25

Maestro-600 Installation Manual

Uploaded by

Copyright:

Available Formats

Maestro-600 Installation Manual

Uploaded by

Document Information

Copyright

Available Formats

Share this document

Share or Embed Document

Sharing Options

Did you find this document useful?

Is this content inappropriate?

Copyright:

Available Formats

Maestro-600 Installation Manual

Uploaded by

Copyright:

Available Formats

0$(6752 0$(6752

6 and 10 Zone Alarm Control Panel Installation Instructions

MAESTRO-600 / MAESTRO-1000 CONTROL PANEL

 (DUWK *URXQG

transformer with a minimum 9$& 9$

40VA rating to provide sufficient

 .H\SDG .H\VZLWFK &RQQHFWLRQV

 .H\SDG =RQH &RQQHFWLRQV

 6LQJOH =RQH ,QSXW &RQQHFWLRQV

 $GYDQFHG 7HFKQRORJ\ =RQH $7=

3.9.3 N.C. Contacts, Without EOL Resistor, With

3.9.4 N.C. Contacts, With EOL Resistor, With

3.11.2 Supervised 4-Wire, Latched, Smoke Detector

 )LUH &LUFXLW

 8VHU  $FFHVV &RGH /HQJWK

 +H[D 6WUHDPOLQHG 3URJUDPPLQJ

 )HDWXUH 6HOHFW 3URJUDPPLQJ

 'HFLPDO 3URJUDPPLQJ

 3$1(/ 6(77,1*6 )25 9,6/2$'

 3DQHO ,GHQWLILHU  &DQFHO &RPPXQLFDWLRQ

 &DOO %DFN

 3& 3DVVZRUG

 $XWRPDWLF (YHQW %XIIHU

Key Access Programming Î key [TRBL]

Key Access Programming Î Key [ AWAY]

Feature Select Programming Î Address 092, keys [1] to [0]

Feature Select Programming Î Address 096, keys [1] to [0]

Sec. 7.13 Sec. 7.9.1

Figure 25 - Zone Related Features

 3DUWLWLRQLQJ 0DHVWUR RQO\

Feature Select Programming Î Address 086, key [HOME] & [AWAY]

 5HSRUWLQJ (YHQW &RGHV

 $XWR 7HVW 5HSRUW

 0DQXDO 7HVW 5HSRUW

Decimal Programming Î Addresses 060

Default: Disabled Auto Arming Options

Off Off “Regular Arming” Bell Cut-Off Time

 ´2QH.H\µ +RPH  µ6\VWHP $µ  6LOHQW =RQHV 6LOHQW 3DQLFV

3XVKEXWWRQ  %HOO &XW2II 7LPH

 3DQHO 7LPH

 7LPH &RUUHFWLRQ

Feature Select Programming ÎAddress 086, key [7]

Feature Select Programming Î Address 086, key [0]

Default: Pulse USA 1:1.5 [2nd] - No adjustment [8]- Minus 4 seconds

 .H\SDG 3DQLF 2SWLRQV

 7DPSHU:LUH )DXOW 5HFRJQLWLRQ

 $UPLQJ'LVDUPLQJ 3DUWLWLRQV

 .H\VZLWFK RU 3XVKEXWWRQ $UPLQJ 

'LVDUPLQJ enable chiming when there is no AC power (orange “power” LED

 7URXEOH 'LVSOD\ 0RQLWRULQJ

You might also like

0$(6752 0$(6752

(DUWK *URXQG

transformer with a minimum 9$& 9$

.H\SDG .H\VZLWFK &RQQHFWLRQV

.H\SDG =RQH &RQQHFWLRQV

6LQJOH =RQH ,QSXW &RQQHFWLRQV

$GYDQFHG 7HFKQRORJ\ =RQH $7=

)LUH &LUFXLW

8VHU $FFHVV &RGH /HQJWK

+H[D 6WUHDPOLQHG 3URJUDPPLQJ

)HDWXUH 6HOHFW 3URJUDPPLQJ

'HFLPDO 3URJUDPPLQJ

3$1(/ 6(77,1*6 )25 9,6/2$'

3DQHO ,GHQWLILHU &DQFHO &RPPXQLFDWLRQ

&DOO %DFN

3& 3DVVZRUG

$XWRPDWLF (YHQW %XIIHU

3DUWLWLRQLQJ 0DHVWUR RQO\

5HSRUWLQJ (YHQW &RGHV

$XWR 7HVW 5HSRUW

0DQXDO 7HVW 5HSRUW

´2QH.H\µ +RPH µ6\VWHP $µ 6LOHQW =RQHV 6LOHQW 3DQLFV

3XVKEXWWRQ %HOO &XW2II 7LPH

3DQHO 7LPH

7LPH &RUUHFWLRQ

.H\SDG 3DQLF 2SWLRQV

7DPSHU:LUH )DXOW 5HFRJQLWLRQ

$UPLQJ'LVDUPLQJ 3DUWLWLRQV

.H\VZLWFK RU 3XVKEXWWRQ $UPLQJ

7URXEOH 'LVSOD\ 0RQLWRULQJ